INSTALLATION INSTRUCTIONS
Medium Panel Pole Mount
JPP SERIES
JPP SERIES Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, Inc., and its affiliated corporations
and subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the JPP up to (and
including) the display does not exceed 75 lbs (34.02 kg).
•The weight capacity of the JPP mount may be LIMITED
to the lowest weight capacity of any other component
located between the JPP and the supporting structure!
Chief® and Centris™ are trademarks of Milestone AV
Technologies, Inc. All rights reserved.
DIMENSIONS
3.94
100
3.94
100
6.00
152
7.46
189
4.43
112
1.97
50
3.68
CENTER OF PIPE
94
5.03
128
UP-DOWN TILT
15
LEFT-RIGHT SWIVEL
75
MEASUREMENTS IN:
[INCHES]
MILLIMETERS
Installation Instructions JPP SERIES
3
LEGEND Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
JPP SERIES Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
5/32" 3/16"
I/M
Interface Bracket
Kit
(including hardware)
x 1
x 1 A (1)
B (1)
C (3)
1/4-20 x 1-1/4"
Installation Instructions JPP SERIES
5
INSTALLATION
IMPORTANT ! : The following installation instructions
assume that a 1-1/2" NPT pipe has been properly
installed and is in place.
1. Determine approximate location for mount keeping in mind
display size, extension, height adjustment (if applicable),
and pitch/roll requirements.
2. Place mount (A) against pole, with clamp (B) on opposite
side of pole (See Figure 1). Using 5/32" hex key, loosely
assemble with three 1/4-20 x 1-1/4" button head cap
screws (C).
Figure 1
NOTE: Equally tighten screws (C) against clamp (B) and
mount (A). (See Figure 2)
Figure 2
3. Position mount at desired height and orientation. Tighten
screws (C) securely.
Display Installation
1. Determine mounting pattern on display.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY AND DAMAGE TO EQUIPMENT! DO NOT
substitute hardware. Use only hardware supplied by
manufacturer!
WARNING: IMPROPER INSTALLATION CAN LEAD TO
ELECTRIC SHOCK OR DAMAGE TO EQUIPMENT! Screw
length must not exceed the depth of threaded mounting insert
in display.
WARNING: OVERTIGHTENING OF SCREWS CAN
DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL
INJURY AND DAMAGE TO EQUIPMENT! DO NOT over
tighten screws when installing interface bracket.
NOTE: If the display being installed has a 100x100 VESA
mounting pattern, no interface bracket is required and
the display can be mounted directly to the Centris cup
as outlined below.
NOTE: If the display being installed requires an interface
bracket, refer to the interface bracket installation
instructions.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display! Proper screws will
easily and completely thread into display mounting holes.
Ensure that screws are not too long.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread
engagement in display may cause display to fall! Back out
screws ONLY as necessary to allow installation of Centris
cup!
1. Start two M4 x 8mm Phillips pan head screws (included in
hardware kit) into upper mounting holes in display back.
(See Figure 3)
NOTE: Leave at least 1/8" of each screw protruding out back
of display.
Figure 3
(A)
Pole
(B)
(C) x 3
2
Keep equal
distance between
mount and
clamp when
tightening
(C) x 3
(B)
(A)
x2
1
JPP SERIES Installation Instructions
6
2. Align two screws in display back with upper mounting holes
in Centris cup and lower display until screws are seated in
lower area of teardrop mounting holes. (See Figure 4)
3. Install two more of the same screws through lower mounting
holes in Centris cup and into display back. (See Figure 4)
4. Tighten all hardware.
5. Route cables and wires to display.
Figure 4
ADJUSTMENTS
To adjust display Roll, Pitch, and YAW tension:
1. Disconnect all wires and cable from the display.
2. Remove two Lower screws securing display to Centris cup.
3. Loosen two Upper screws securing display.
4. Lift display upward and away from mount.
5. Using a hex head wrench, turn the tension adjustment
screw clockwise to increase tension, or counter-clockwise
to decrease tension. (See Figure 5)
6. Re-install display.
Figure 5
x 2
23
4
Installation Instructions JPP SERIES
7
JPP SERIES Installation Instructions
Chief Manufacturing, a products division
of Milestone AV Technologies
8832-000238 RevC
2009 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
11/09
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief JPP210S Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief JPP210S Installation guide
Documents connexes
-
Chief JWSVB Guide d'installation
-
Chief JWDIWUB Guide d'installation
-
Chief JPP210S Guide d'installation
-
-
-
Chief KSA1024B Guide d'installation
-
Chief PACCS1 Guide d'installation
-
-
-