Modern Forms PD-89924 Groovy Mode d'emploi
- Taper
- Mode d'emploi
INSTALLATION INSTRUCTIONS
899-LED Pendants
PD-89924/ PD-89936/ PD-89948
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER
BEFORE BEGINNING.
-Read all instructions before installing.
-System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local
regulations.
-When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
-Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts
and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product
by Modern Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the
manufacturer if any parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in
coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.
-Lisez toutes les instructions avant l’installation.
-Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également
aux règlements locaux.
-Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé
seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou
accessoires non conçus pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également
causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont
endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous
recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes
les deux semaines avec un chiffon humide.
HARDWARE
INSTALLATION INSTRUCTIONS
899-LED Pendants
PD-89924/ PD-89936/ PD-89948
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for
installation.
ASSEMBLING THE FELT SHADE (Fig.1˅
3. Unfold felt assembly with buttons facing up (11 sets assembled by button, 1 set tied up with wire tie).
4. Align the spread felt pieces as shown (Fig. 1), then connect them using the buttons and button posts. Layer the branches before
attaching them. Connect all 11 felt assembly sets. The buttons should be facing up.
NOTE: The felt pieces are flexible and will take shape as they are assembled together. Do not bend the felt pieces.
5. Cut off the wire tie on the last set of felt assembly and connect each piece upon the felt shade. Keep the top five branches open
for light source installation.
NOTE: If the assembled felt ball becomes misshapen due to gravity factors such as long suspension or moisture, it can be
disassembled and ironed piece by piece with an iron. After flatting the felt pieces, assemble them again.
Layer each felt branch
before buttoning up
INSTALLATION INSTRUCTIONS
899-LED Pendants
PD-89924/ PD-89936/ PD-89948
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
ASSEMBLING THE LIGHT SOURCE (Fig.2)
6. Thread the cable through the inner rod (packed with felt assembly). Carefully insert the bracket into the glass, place the cover on
the glass, secure it with the rod nut.
7. Thread the tube onto the inner rod, put the support cover through the tube and inner rod open side facing up. Insert rod
assembly into the felt shade from the top. Insert the wire and tube through the open section of the fabric shade and secure
them with the washer and fixing nut.
ASSEMBLING THE DOWNROD AND CANOPY (Fig.3˅
8. Choose the number of downrods suitable to your application. Thread the fixture wire through the rods, swivel and canopy. Connect
the canopy, rods and fixing nut, making sure all are tightened.
INSTALLATION INSTRUCTIONS
899-LED Pendants
PD-89924/ PD-89936/ PD-89948
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
CONNECTING THE WIRES (Fig. 4)
9. Connect the driver’s input wires to junction box wires as shown (Fig. 4). Make sure that all wire connectors (A) are secure. If your
outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground
wire directly to the back plate using the green screw provided.
NOTE: This fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specific
dimming wiring information.
COMPLETING THE INSTALLATION
10. Remove the mounting plate screw (B) and mounting plate from the fixture.
11. Secure mounting plate to the junction box using the screws provided with the junction box.
NOTE: The side of the mounting plate marked “GND” must face out.
12. Secure the safety cord (E) to the inside of the canopy with the swivel fixed nut, hook the safety cord to the mounting plate (Fig. 5)
(for PD-89936/ PD-89948 only).
13. Secure the fixture to the mounting plate using the mounting plate screw (B).
14. For sloped ceiling applications, rotate swivel at the top of the stem to ensure luminaire is aiming down.
DIMMING WIRING INSTRUCTIONS (Fig. 6)
16. To utilize ELV or TRAIC dimming: use black (hot), white (neutral) and bare copper ground wires (ground).
17. To utilize 0-10V dimming: use purple (dim+), gray (dim-), black (hot), white (neutral) and bare copper ground wires (ground).
NOTE: Make sure to connect 0-10V prior to powering up the fixture in order to allow the 0-10V dimming to function properly.
Fig. 6
Driver
Purple - Dim+
Gray - Dim-
Black - Hot
White - Neutral
Red - Fixt
ur
e+
Black - Fixt
ur
e-
-
1
-
2
-
3
-
4
Modern Forms PD-89924 Groovy Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms WS-93037 Argo Mode d'emploi
-
-
-
-
-
-
-
-
-