ASSEMBLY & INSTALLATION INSTRUCTIONS
Fixture
BPD74232
Schonbek, 61 Industrial Blvd, Plattsburg, New York, 12901| Phone: 1-800-836-1892 | Fax: 518-563-4228 www.schonbek.com | JAN 2021 | 4
HARDWARE
Fig. 3 Switch
3500K3000K 4000K
Fig. 2 Wiring
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Schonbek, 61 Industrial Blvd, Plattsburg, New York, 12901
Phone: 1-800-836-1892 | Fax: 518-563-4228 |
www.schonbek.com
A
BCD
Wire Connector
Qty: 3PCS+1 Extra Qty: 3PCS+1 Extra Qty: 3PCS+1 Extra Qty: 3PCS+1 Extra
Mounting screw Wood screw Plastic anchor
Back Plate Dimensions
Canopy
Cable(Cut)
Red +
White - Neutral
Black - Hot
Driver
Input
Output
Purple - Dim+Pink or gray - Dim-
Black -
Red +
White +
Black -
Green-
Black -
brown -
3000K 3500K 4000K
Fig. 4
ASSEMBLY & INSTALLATION INSTRUCTIONS
Fixture
BPD74232
Schonbek, 61 Industrial Blvd, Plattsburg, New York, 12901| Phone: 1-800-836-1892 | Fax: 518-563-4228 www.schonbek.com | JAN 2022 | 3
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE Crystal AND FIXTURE (Fig. 1and Fig.3)
3. Install from the inside, the Cloud crystal against the spring sheet, press hard, the two convex points of the crystal are aligned with the two holes of
the xture, so that the spring can automatically return.
4. Remove the mounting screw (B) from the xture.
5. The lamp can switch between three color temperatures (3000k-3500k-4000k), which can be adjusted to your preference with the switch in the
canopy (Fig.4).
6. Drill holes in the wall aligned with the key holes located in the mounting back plate, insert the plastic anchor (D).
7. Secure the mounting plate to the junction box using junction box screws. fasten it to the wall using wood screws (C).
Note: (i) using any other non-original-manufacturer provided junction box screw may result in safety issue;
(ii) The side of the mounting plate marked “GND” must face out.
8. Adjust the xture wire length by pushing the cable gripper on the canopy and pulling the wire as desired.
a. Retract these wires close to a desirable length to within the canopy before securing the xture in place.Note: retracting or extending excessive
cable length through the cable gripper is not recommended.
b. Warning: Shortening these cables without professional helps or electronic background is not advisable. Any modications to the xture may
result in voiding the warranty of the product.
CONNECTING THE WIRES (Fig. 2)
9. Hook the safety cords to the mounting plate.
10. Connect the driver input/output wires with junction box wires as shown in Fig.2, making sure that all wire connectors (A) are secured. If your outlet
box has a green or bare c opper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
mounting plate usingthe screw provided. After wires are connected, tuck them carefully inside the junction box.
11 Secure the xture by mounting the canopy to the ring of the backplate. Turn and rotate the canopy until it stops. Fasten the canopy to the back plate
using the mounting screw (B).
NOTE: DIMMING WIRING INFORMATION (Fig. 4)
12 This xture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specic dimming wires information.
13 To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground).
14. To utilize 0-10V dimming: use wire purple (dim+), Pink or gray (dim-), black (hot), white (neutral) and bare copper ground wire (ground).
ASSEMBLY & INSTALLATION INSTRUCTIONS
Fixture
BPD74232
Schonbek, 61 Industrial Blvd, Plattsburg, New York, 12901| Phone: 1-800-836-1892 | Fax: 518-563-4228 www.schonbek.com | JAN 2022 | 2
WARNING
IMPORTANT: NEVER attempt any work without shutting off the electricity.
o Read all instructions before installing.
o System is intended for installation in accordance with the National Electrical Code
(NEC), other applicable installation code(s) and local regulations by a licensed
electrician familiar with the operation of the product and the hazards involved.
o Go to the main fuse box, or circuit breaker panel. Place the main power switch in
the “OFF” position and unscrew the fuse (s) or switch ”OFF” the circuit breaker
switch (es) that control the power to the fixture (s) or room that you are working
on.
o Place the wall switch in the “OFF” position.
o FAILURE TO INSTALL THIS FIXTURE IN ACCORDANCE WITH THESE INSTRUCTIONS
MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND/OR PROPERTY
DAMAGE.
CAUTION
o All parts must be used as indicated in these instructions. Do not substitute any
parts, leave parts out, or use any parts that are worn out or broken. Failure to
follow this instruction could invalidate the ETL/CETL Listing of this fixture.
o When handling the fixture, do not apply pressure to the LEDs or bulbs. Hold the
fixture by the base only.
o Do not exceed maximum wattage noted on the fixture. Use only the
recommended LED or standard lamps with the fixture.
ADVERTENCIA
IMPORTANTE: NUNCA trate de hacer ningún trabajo sin desconectar la electricidad.
o Lea todas las instrucciones antes de instalar.
o El sistema tiene por objeto la instalación de acuerdo con el Código Eléctrico
Nacional, y otros códigos de instalación y reglamentos locales aplicables, por
parte de un electricista autorizado que esté familiarizado con el funcionamiento
del producto y los peligros involucrados.
o Vaya a la caja de fusibles o al panel de disyuntores principal. Ponga el
interruptor principal de alimentación en la posición de "APAGADO", y
desenrosque los fusibles o "DESCONECTE" los disyuntores que controlen la
alimentación a los dispositivos o la habitación en los que usted esté trabajando.
o Ponga el interruptor de pared en la posición de "APAGADO".
o EL HECHO DE NO INSTALAR ESTE DISPOSITIVO DE ACUERDO CON ESTAS
INSTRUCCIONES PODRÍA RESULTAR EN UNA LESIÓN PERSONAL GRAVE O LA
MUERTE, Y/O DAÑOS A LA PROPIEDAD.
PRECAUCIÓN
o Todas las piezas deben usarse como se indica en estas instrucciones.No
sustituya ninguna pieza, no deje piezas fuera, ni utilice ninguna pieza que esté
desgastada ni rota. El hecho de no seguir estas instrucciones podría invalidar la
certificación ETL/CETL de este dispositivo.
o Al manipular el dispositivo, no aplique presión a los LED ni las bombillas. Sujete
el dispositivo solo por la base.
o No exceda la potencia máxima indicada en el dispositivo. Use solo los LED o las
bombillas estándar recomendados con el dispositivo.
ADVERTENCIA
IMPORTANTE: NUNCA trate de hacer ningún trabajo sin desconectar la electricidad.
IMPORTANT : Ne JAMAIS entreprendre des travaux sans couper l’électricité.
o Lire toutes les instructions avant l’installation.
o Ce système est conçu pour être installé conformément au Code national de
l’électric
ité ou d’autres codes d’installation et réglementations locales en vigueur
par un électricien agréé connaissant le fonctionnement de ce produit et les
dangers qu’il comporte.
o Aller à la boîte à fusibles ou panneau principal de disjoncteurs. Placer
l’interrupteur d’alimentation principal sur « ARRÊT » et dévisser le ou les fusibles
ou mettre sur « ARRÊT » le ou les disjoncteurs qui contrôlent l’alimentation du
ou des appareils électriques ou de la pièce dans laquelle vous travaillez.
o Mettre l’interrupteur mural sur « ARRÊT » .
o NÉGLIGER D’INSTALLER CET APPAREIL CONFORMÉMENT À CES INSTRUCTIONS
RISQUE D’ENTRAÎNER DE GRAVES BLESSURES PERSONNELLES OU LA MORT
AINSI QUE DES DOMMAGES MATÉRIELS.
o MISE EN GARDE
o Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ne
remplacer aucune pièce, ne laisser aucune pièce de côté ou n’utiliser aucune
pièce usée ou cassée. Le non-respect de cette directive peut invalider
l’homologation ETL/CETL de cet appareil.
o Lors de la manipulation de cet appareil, n’appliquer aucune pression sur les DEL
ou les ampoules. Maintenir l’appareil par la base uniquement.
o Ne pas dépasser le nombre de watts maximum indiqué sur l’appareil. N’utiliser
que les DEL ou ampoules standard recommandées dans cet appareil.
U.L. Approved 200LB.Max.
Outlet Box and Hardware
(Sold Separately)
Mounting Backplate
Mounting Screw
Wire Connector Plastic anchor
Wood Screws
Cloud Crystal
RPL-GLA-74232
Fixture
3CCT Switch
Driver
Safety Cords
Spring sheet
D
A
CB
Junction Box Screw
Adjust the fixture wire length by
pushing the cable gripper on
the canopy and pulling the wire
as desired.
Cable-gripper
Push up
Ground Wire
junction box
Fig. 1
-
1
-
2
dans d''autres langues
- English: Schonbek BPD74232 User manual
- español: Schonbek BPD74232 Manual de usuario
Documents connexes
Autres documents
-
Modern Forms PD-53046 Racetrack Mode d'emploi
-
-
-
-
-
-
-
-