Yamaha M7CL Guide d'installation

Catégorie
Logiciel
Taper
Guide d'installation

Ce manuel convient également à

Studio Manager Version 2 Installation Guide 1
Studio Manager Version 2
Studio Manager Version 2
Installation Guide
Installation Guide
ATTENTION
PLEASE READ THIS SOFTWARE LICENSE AGREEMENT ("AGREEMENT") CAREFULLY BEFORE USING THIS SOFTWARE. YOU ARE ONLY
PERMITTED TO USE THIS SOFTWARE PURSUANT TO THE TERMS AND CONDITIONS OF THIS AGREEMENT. THIS AGREEMENT IS
BETWEEN YOU (AS AN INDIVIDUAL OR LEGAL ENTITY) AND YAMAHA CORPORATION ("YAMAHA").
BY DOWNLOADING, INSTALLING, COPYING, OR OTHERWISE USING THIS SOFTWARE YOU ARE AGREEING TO BE BOUND BY THE TERMS
OF THIS LICENSE. IF YOU DO NOT AGREE WITH THE TERMS, DO NOT DOWNLOAD, INSTALL, COPY, OR OTHERWISE USE THIS
SOFTWARE. IF YOU HAVE DOWNLOADED OR INSTALLED THE SOFTWARE AND DO NOT AGREE TO THE TERMS, PROMPTLY DELETE THE
SOFTWARE.
1. GRANT OF LICENSE AND COPYRIGHT
Yamaha hereby grants you the right to use one copy of the software program(s) and data ("SOFTWARE") accompanying this Agreement. The
term SOFTWARE shall encompass any updates to the accompanying software and data. The SOFTWARE is owned by Yamaha and/or
Yamaha’s licensor(s), and is protected by relevant copyright laws and all applicable treaty provisions. While you are entitled to claim ownership
of the data created with the use of SOFTWARE, the SOFTWARE will continue to be protected under relevant copyrights.
You may use the SOFTWARE on a single computer.
You may make one copy of the SOFTWARE in machine-readable form for backup purposes only, if the SOFTWARE is on media where
such backup copy is permitted. On the backup copy, you must reproduce Yamaha's copyright notice and any other proprietary legends
that were on the original copy of the SOFTWARE.
You may permanently transfer to a third party all your rights in the SOFTWARE, provided that you do not retain any copies and the
recipient reads and agrees to the terms of this Agreement.
2. RESTRICTIONS
You may not engage in reverse engineering, disassembly, decompilation or otherwise deriving a source code form of the SOFTWARE
by any method whatsoever.
You may not reproduce, modify, change, rent, lease, or distribute the SOFTWARE in whole or in part, or create derivative works of the
SOFTWARE.
You may not electronically transmit the SOFTWARE from one computer to another or share the SOFTWARE in a network with other
computers.
You may not use the SOFTWARE to distribute illegal data or data that violates public policy.
You may not initiate services based on the use of the SOFTWARE without permission by Yamaha Corporation.
Copyrighted data, including but not limited to MIDI data for songs, obtained by means of the SOFTWARE, are subject to the following
restrictions which you must observe.
Data received by means of the SOFTWARE may not be used for any commercial purposes without permission of the copyright owner.
Data received by means of the SOFTWARE may not be duplicated, transferred, or distributed, or played back or performed for listeners
in public without permission of the copyright owner.
The encryption of data received by means of the SOFTWARE may not be removed nor may the electronic watermark be modified
without permission of the copyright owner.
3. TERMINATION
This Agreement becomes effective on the day that you receive the SOFTWARE and remains effective until terminated. If any copyright law or
provisions of this Agreement is violated, the Agreement shall terminate automatically and immediately without notice from Yamaha. Upon such
termination, you must immediately destroy the licensed SOFTWARE, any accompanying written documents and all copies thereof.
4. DISCLAIMER OF WARRANTY ON SOFTWARE
You expressly acknowledge and agree that use of the SOFTWARE is at your sole risk. The SOFTWARE and related documentation are provided
"AS IS" and without warranty of any kind. NOTWITHSTANDING ANY OTHER PROVISION OF THIS AGREEMENT, YAMAHA EXPRESSLY
DISCLAIMS ALL WARRANTIES AS TO THE SOFTWARE, EXPRESS, AND IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS.
SPECIFICALLY, BUT WITHOUT LIMITING THE FOREGOING, YAMAHA DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR
REQUIREMENTS, THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE, OR THAT DEFECTS IN THE
SOFTWARE WILL BE CORRECTED.
SOFTWARE LICENSE AGREEMENT
Studio Manager Version 2 Installation Guide 2
5. LIMITATION OF LIABILITY
YAMAHA’S ENTIRE OBLIGATION HEREUNDER SHALL BE TO PERMIT USE OF THE SOFTWARE UNDER THE TERMS HEREOF. IN NO EVENT
SHALL YAMAHA BE LIABLE TO YOU OR ANY OTHER PERSON FOR ANY DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY DIRECT,
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, EXPENSES, LOST PROFITS, LOST DATA OR OTHER DAMAGES ARISING OUT OF
THE USE, MISUSE OR INABILITY TO USE THE SOFTWARE, EVEN IF YAMAHA OR AN AUTHORIZED DEALER HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. In no event shall Yamaha's total liability to you for all damages, losses and causes of action (whether in
contract, tort or otherwise) exceed the amount paid for the SOFTWARE.
6. THIRD PARTY SOFTWARE
Third party software and data ("THIRD PARTY SOFTWARE") may be attached to the SOFTWARE. If, in the written materials or the electronic data
accompanying the Software, Yamaha identifies any software and data as THIRD PARTY SOFTWARE, you acknowledge and agree that you must
abide by the provisions of any Agreement provided with the THIRD PARTY SOFTWARE and that the party providing the THIRD PARTY
SOFTWARE is responsible for any warranty or liability related to or arising from the THIRD PARTY SOFTWARE. Yamaha is not responsible in any
way for the THIRD PARTY SOFTWARE or your use thereof.
•Yamaha provides no express warranties as to the THIRD PARTY SOFTWARE. IN ADDITION, YAMAHA EXPRESSLY DISCLAIMS ALL
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, as to the THIRD PARTY SOFTWARE.
•Yamaha shall not provide you with any service or maintenance as to the THIRD PARTY SOFTWARE.
•Yamaha is not liable to you or any other person for any damages, including, without limitation, any direct, indirect, incidental or
consequential damages, expenses, lost profits, lost data or other damages arising out of the use, misuse or inability to use the THIRD
PARTY SOFTWARE.
7. GENERAL
This Agreement shall be interpreted according to and governed by Japanese law without reference to principles of conflict of laws. Any dispute
or procedure shall be heard before the Tokyo District Court in Japan. If for any reason a court of competent jurisdiction finds any portion of this
Agreement to be unenforceable, the remainder of this Agreement shall continue in full force and effect.
8. COMPLETE AGREEMENT
This Agreement constitutes the entire agreement between the parties with respect to use of the SOFTWARE and any accompanying written
materials and supersedes all prior or contemporaneous understandings or agreements, written or oral, regarding the subject matter of this
Agreement. No amendment or revision of this Agreement will be binding unless in writing and signed by a fully authorized representative of
Yamaha.
The software and this manual are the exclusive copyrights of Yamaha Corporation.
Please read carefully the Software Licensing Agreement at the front of this manual before installing the application.
Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of
the manufacturer.
•Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for
the results of the use of this manual and the software.
Future upgrades of application and system software and any changes in specifications and functions will be announced at the following
website.
http://www.yamahasynth.com/download/ (Music Production)
http://www.yamahaproaudio.com/ (Professional Audio)
The screen displays as illustrated in this manual are for instructional purposes, and may appear somewhat different from the screens which
appear on your computer.
The illustrations and LCD screens as shown in this owner’s manual are for instructional purposes only, and may appear somewhat different
from those on your instrument.
Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for
your personal use.
Windows is the registered trademarks of Microsoft
®
Corporation.
Apple and Macintosh are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.
The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.
Special Notices
Studio Manager Version 2 Installation Guide 3
Studio Manager is a cross-platform application that enables you to start multiple Editors that control YAMAHA
hardware products remotely, and to save multiple Editor settings.
You can run Studio Manager as a stand-alone application, or as a plug-in within DAW (digital audio workstation)/
sequencer applications that are compatible with Total Recall, such as Cubase SX 3.0.1 or later. In either case, the
basic functionality is the same. For the latest information on compatible DAW applications, refer to the following
website.
http://www.studioconnections.org/
The actual installation steps and the use of the software itself differs depending on the operating system that you
are using. Please refer to the appropriate installation instructions.
For subsequent operations, refer to the PDF manual from the [HELP] menu in each software program.
Precautions when using the USB TO HOST connector
When connecting the computer to the USB TO HOST connector, make sure to observe the following points. Failing to do so
risks freezing the computer and corrupting or even losing the data. If the computer or the instrument freezes, turn the power
to the instrument off or restart the computer.
Before connecting the computer to the USB TO HOST connector, exit from any power-saving mode
(such as suspended, sleep, standby) of the computer.
Before turning on the power to the instrument, connect the computer to the USB TO HOST connector.
Execute the following before turning the power to the instrument on/off or plugging/unplugging the USB
cable to/from the USB TO HOST connector.
- Quit any open applications.
- Make sure that data is not being transmitted from the instrument. (Data is transmitted only by playing
notes on the keyboard or playing back a song.)
While a USB device is connected to the instrument, you should wait for six seconds or more between
these operations: (1) when turning the power of the instrument off then on again, or (2) when alternately
connecting/disconnecting the USB cable.
Studio Manager
Installing the Software
Procedures Windows Macintosh
1
Verify that your system meets the operating requirements of each software
program.
page 4 page 7
2
Install the appropriate driver to your computer. page 4 page 7
3
Install the Studio Manager and each editor. page 6 page 8
4
Start up the Studio Manager, then start up the editor.
Refer to the PDF manual and
installation guide for your
particular editor.
CAUTION
Studio Manager Version 2 Installation Guide 4
Minimum System Requirements
Make sure that the computer you are using satisfies the recommended system requirements for each editor
software. For details about the system requirements, refer to the owner’s manual for each editor.
n The system requirements may differ slightly depending on the particular operating system.
Windows Software Installation
To use the Studio Manager, you’ll need to install the following software programs. Follow the appropriate
instructions below corresponding to the software you’re using.
Driver Installation
Depending on the cable connection you are using, install the USB-MIDI driver or DME-N Network Driver or mLAN
Tools.
n You can also use MIDI cables to connect your Yamaha hardware to the computer. For details, refer to the owner's manual of your
particular MIDI interface.
• USB-MIDI Driver
To operate your Yamaha hardware from your computer via USB, you’ll need to install the USB-MIDI driver software.
The USB-MIDI driver is software that transfers MIDI data back and forth between your sequencer software and the
hardware via a USB cable.
For Windows Users
USB-MIDI driver (when connecting via USB) , DME-N Network Driver (when connecting via Ethernet) or mLAN
Tools (when connecting via mLAN)
Studio Manager
Editor software for your particular hardware
You can download the latest version of the USB-MIDI driver at the following website. For specific installation instructions,
refer to the installation guide included in the downloaded file.
http://www
.global.yamaha.com/download/usb_midi/
MUSIC PRODUCTION SYNTHESIZER
Sequencer
USB cable
Driver
Computer
Yamaha hardware with a USB interface
Studio Manager Version 2 Installation Guide 5
• DME-N Network Driver
To operate your Yamaha hardware from your computer via Ethernet, you'll need to install the DME-N Network Driver
software.
DME-N Network Driver is software that transfers MIDI data back and forth between your computer and the
hardware via Ethernet cable.
You can download the latest version of DME-N Network Driver at the following website. For specific installation
instructions, refer to the installation guide included in the downloaded file.
http://www.yamahaproaudio.com/
• mLAN Tools
To operate your mLAN device from your computer via mLAN, you’ll need to install the mLAN Tools software.
Included with mLAN Tools are driver and applications software for transferring audio/MIDI data, and setting the
audio/MIDI connections between the computer and the mLAN devices via an mLAN cable.
You can download the latest version of mLAN Tools at the following website. For specific installation instructions, refer to the
installation guide included in the downloaded file.
http://www
.yamahasynth.com/download/
Ethernet cable
Yamaha hardware with an Ethernet interface
Computer
Editor
Ethernet cable
Hub
or
Crossover cable
Driver
mLAN Tools
MUSIC PRODUCTION SYNTHESIZER
Sequencer
IEEE1394 cable
Computer
mLAN device
Studio Manager Version 2 Installation Guide 6
Studio Manager Installation
Studio Manager is a cross-platform application that enables you to use multiple Editor programs for remotely
controlling Yamaha hardware from your computer, and allows you to save the Editor settings for instant recall.
For specific instructions on using the software, refer to the PDF manual from the [HELP] menu in the Studio
Manager and each Editor.
Follow the instructions below to install the software programs.
1 Extract the data from the downloaded compressed file and open the “sm***w” folder.
“***” represents the version number.
2 Double-click “setup.exe.
A setup dialog of Studio Manager is displayed.
3 Follow the on-screen instructions to install the software.
For specific instructions on using the software, refer to the PDF manual from the [HELP] menu in each program.
Editor Installation
Each Yamaha Editor is a software program designed to work with a specific Yamaha hardware product, letting you
edit settings for the product completely from a connected computer.
Follow the instructions below to install the software programs.
Uninstall (removing the installed application)
To remove the installed editors and Studio Manager:
Select [START] [Control Panel] [Add/Remove Programs] [Install/Uninstall], then select the application to be
removed and click [Add/Remove…].
Follow the on-screen instructions to uninstall the application.
n The button names or menus may differ depending on the computer OS.
You can download the latest version editor for each hardware at the following website. For specific installation instructions,
refer to the installation guide included in the downloaded file.
http://www
.yamahasynth.com/download/ (Music Production)
http://www
.yamahaproaudio.com/ (Professional Audio)
Studio Manager Version 2 Installation Guide 7
Minimum System Requirements
Make sure that the computer you are using satisfies the recommended system requirements for each editor
software. For details about the system requirements, refer to the owner’s manual for each editor.
n The system requirements may differ slightly depending on the particular operating system.
Macintosh Software Installation
To use the Studio Manager, you’ll need to install the following software programs. Follow the appropriate
instructions below corresponding to the software you’re using.
Driver Installation
Depending on the cable connection you are using, install the USB-MIDI driver or mLAN Tools.
n You can also use MIDI cables to connect your Yamaha hardware to the computer. For details, refer to the owner’s manual of your
particular MIDI interface.
• USB-MIDI Driver
To operate your Yamaha hardware from your computer via USB, you’ll need to install the USB-MIDI driver software.
The USB-MIDI driver is software that transfers MIDI data back and forth between your sequencer software and the
hardware via a USB cable.
For Macintosh Users
USB-MIDI driver (when connecting via USB) or mLAN Tools (when connecting via mLAN)
Studio Manager
Editor software for your particular hardware
You can download the latest version of the USB-MIDI driver at the following website. For specific installation instructions,
refer to the installation guide included in the downloaded file.
http://www
.global.yamaha.com/download/usb_midi/
MUSIC PRODUCTION SYNTHESIZER
Sequencer
USB cable
Driver
Computer
Yamaha hardware with a USB interface
Studio Manager Version 2 Installation Guide 8
• mLAN Tools
To operate your mLAN device from your computer via mLAN, you’ll need to install the mLAN Tools software.
Included with mLAN Tools are driver and applications software for transferring audio/MIDI data, and setting the
audio/MIDI connections between the computer and the mLAN devices via an mLAN cable.
n Depending on your OS version, the mLAN connection may not function properly. For details, refer to the installation guide included with
mLAN Tools.
Studio Manager Installation
Studio Manager is a cross-platform application that enables you to use multiple Editor programs for remotely
controlling Yamaha hardware from your computer, and allows you to save the Editor settings for instant recall.
For specific instructions on using the software, refer to the PDF manual from the [HELP] menu in the Studio
Manager and each Editor.
1 Extract the data from the downloaded compressed file and open the “sm***mx” folder.
“***” represents the version number.
2 Double-click “Install Studio Manager.mpkg.
A setup dialog of Studio Manager is displayed.
3 Follow the on-screen instructions to install the software.
Editor Installation
Each Yamaha Editor is a software program designed to work with a specific Yamaha hardware product, letting you
edit settings for the product completely from a connected computer.
Follow the instructions below to install the software programs.
You can download the latest version of mLAN Tools at the following website. For specific installation instructions, refer to the
installation guide included in the downloaded file.
http://www
.yamahasynth.com/download/
You can download the latest version editor for each hardware at the following website. For specific installation instructions,
refer to the installation guide included in the downloaded file.
http://www
.yamahasynth.com/download/ (Music Production)
http://www
.yamahaproaudio.com/ (Professional Audio)
mLAN Tools
MUSIC PRODUCTION SYNTHESIZER
Sequencer
IEEE1394 cable
Computer
mLAN device
Studio Manager Version 2 Installation Guide 9
Please refer to the installation guide and PDF manual for your particular editor, as well as the Studio Manager PDF
manual. You can open the PDF manuals for the editor and Studio Manager from the [HELP] menu.
When controlling the hardware from a computer via USB/Ethernet/mLAN, the hardware does not
operate correctly or no sound is heard.
•Have you installed the latest driver?...........................................................................Windows: page 4, Macintosh: page 7
Is the USB/mLAN cable connected correctly?................................................ Owner’s manual for your particular hardware
Is the Ethernet cable connected correctly?
Connect the computer to the hardware by using an Ethernet cable via a hub. When connecting the computer to the hardware
directly, use a crossover cable.
Are the volume settings of the tone generator, playback device, and application program set to the appropriate
levels?................................................................................ Owner’s manuals for your particular hardware and DAW/sequencer
•Have you selected an appropriate ports in the hardware or DAW/sequence software?
............................................................................................ Owner’s manuals for your particular hardware and DAW/sequencer
If your computer has automatically activated any power-saving mode (such as suspended, sleep, standby) when
using the USB connection, the computer may “freeze,” or the driver may stop working. When using USB, disable
any power-saving mode on the computer.
Playback response is delayed.
Does your computer satisfy the system requirements?.....................................Installation Guide for your particular editor
Is any other application or device driver running?
Getting Started (for both Windows/Macintosh)
Troubleshooting
U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
© 2005 Yamaha Corporation
B0
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Yamaha M7CL Guide d'installation

Catégorie
Logiciel
Taper
Guide d'installation
Ce manuel convient également à