Danfoss System Manager, AK-SM 800A series Guide d'installation

Marque: Danfoss

Modèle: System Manager, AK-SM 800A series

Taper: Guide d'installation

Installation Guide

System Manager

AK-SM 800A series

AN307930531782en-000101 | 1

080R9342

A N307930531782en-000101

-10 °C< t

amb

< 50 °C

14 °F < t

amb

< 120 °F

0 – 95% RH, non condensing

IP20

Danfoss

80Z817

Relay 1/2

Canbus

100 - 240 V

MODBUS 1/2

LON / TP78

Ethernet 0

T 8

Supply Relay 1 Relay 2

LON-version

Canbus

(for future use)

Listed

UL ﬁle: E31024

61B5

Class 2 or LPS in accordance with NEC.

For supply connections, use 16 AWG or

larger wires rated for at least 75 °C (167 °F).

Use copper conducters only.

Enclosure rating type 1

FCC ID: X02SPB209A

IC ID: 8713A-SPB209A

TP 78-version

100 – 240 V

CAN bus

MODBUS

(Danfoss)

MODBUS 2

(RS485)

TP 78

LON 1

TP 78

LON 2

TP 78

LON 3

TP 78

LON 4

LON

MODBUS

1 MODBUS 2

Panel mount

Wall mount

Front side

Danfoss

80Z818

T10

2 | AN307930531782en-000101

Danf

oss

80Z820

Terminering

Termination

Terminierung

Terminaison

Terminación

Connectivity

Selve installationen af datakommunikationskablet skal overholde de krav, som er nævnt i dokumentet “Datakommunikation imellem

ADAP-KOOL® Køleanlægsstyringer”. Litteraturnummer = RC8AC901.

The actual installation of the data communication cable must comply with the requirements mentioned in the document “Data

communication between ADAP-KOOL® Refrigeration controls”. Literature sheet number = RC8AC902.

Beim Verlegen des Datenkommunikationskabels sind die im dokument “Datenkommunikation zwischen ADAP-KOOL®

Kälteanlagenregelsysteme“ enthaltenen Anforderungen einzuhalten. Literaturnummer = RC8AC903.

L’installation elle-même du câble de transmission de données doit respecter les contraintes citées dans le document

“Transmission de données ADAP-KOOL® Commande d’installation frigoriﬁques”. Référence documentaire = RC8AC904.

La instalación práctica del cable de comunicación de datos debe cumplir con los requisitos mencionados en el documento

“Comunicación de datos entre controles de refrigeración ADAP-KOOL®”. Número de documento = RC8AC907.

MODBUS

LON

TP78

Canbus

Ethernet 1 (for future use)

(Accessible outside)

Ethernet 0 (WAN)

(Recessed inside)

Ethernet WiFi Access point

1. Activate WiFi access point from local screen

2. Follow on-screen instructions

When all cables have been mounted on the diﬀerent units, the

cable must be terminated.

A section must be terminated at both ends. The section must

be terminated using either an external resistor or a contact.

Please see the relevant device.

A repeater will normally terminate two cable sections.

The termination should be made with a 120-ohm resistor. (The

resistor can be in the range 100 – 130 ohms.)

A repeater will always terminate two cable sections.

Repeater

System unit

Termination = 120 Ω

Danfoss

80Z819

Out

120

AN307930531782en-000101 | 3

0 = Master

1 - 9 = Slave

Initial settings:

1. Legal terms

2. Select language for local screen

3. Set up user

4. Set Date/time

5. Select Units

6. Set Communication

7. OK and Finish

Konﬁguration, Conﬁguration, Konﬁguration, Conﬁguration, Conﬁguración

See User Guide: BC316842192932en-001001

AK-SM 800

Initial settings wizard

First time start-up

AK-SM 820A

AK-SM 850A

AK-SM 880A

IMPORTANT!

Method 1: Oﬄine

Download ﬁrmware from

sm800a.danfoss.com

Method 2: Online

Use software update utility in the web

interface.

Address

Adresse

Dirección

SOFTWARE UPDATE

4 | AN307930531782en-000101

ADAP-KOOL®

The Product contains electrical components

And may not be disposed together with domestic waste.

Equipment must be separate collected with Electrical and Elec-

tronic waste. According to Local and currently valid legislation.

Statements for the AK-SM 800A

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modiﬁcations not expressly approved could void your authority to use this equipment

This device complies with Part 15 of the FCC Rules. Operation to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation

INDUSTRY CANADA STATEMENT

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may

not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux

conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

NOTICE

FCC COMPLIANT NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Modiﬁcations: Any modiﬁcations made to this device that are not approved by Danfoss may void the authority granted to the user by the FCC to

operate this equipment.

Any regulatory related concerns contact: global_approvals@danfoss.com

Danfoss Cooling

11655 Crossroads Circle

Baltimore, Maryland 21220