Dacor DDW24M999UM Guide d'installation

Installation Instructions

Modernist / Heritage Built-In Dish Washer

DDW24M99* Series

DDW24T99* Series

DACOR_DW9500M_DD68-00197A-01_EN.indd 1 2017-08-23  8:54:48

Contents

English2

Contents

Installation 3

What’s included 3

Installation requirements 7

Dimensions and specications 9

Step-by-step installation 11

DACOR_DW9500M_DD68-00197A-01_EN.indd 2 2017-08-23  8:54:48

Installation

English 3

Installation

Follow these instructions carefully to ensure proper installation of the dishwasher and to

prevent accidents when washing dishes.

What’s included

Make sure all the parts are included in the product package. If you have a question about

the dishwasher or the parts, contact a local Dacor customer center or your retailer. The

actual appearance of the dishwasher may differ, depending on your model and country.

CAUTION

After unpacking the dishwasher, keep the packaging materials out of children’s reach to

ensure their safety.

DDW24T999BB/DA

Top brackets (2 ea) Ø4 X 12 screws

(6 ea)

Protective sticker Sub foot

Custom panel

xers (wood panel

holders, 2 ea)

Ø4 X 43 screws

(4 ea)

Ø4 X 20 screws

(2 ea)

Ø4 X 16 screws

(2 ea)

Rubber skirt

DACOR_DW9500M_DD68-00197A-01_EN.indd 3 2017-08-23  8:54:49

Installation

English4

DDW24M999**, DDW24T998US/DA

Top brackets (2 ea) Ø4 X 12 screws

(6 ea)

Protective sticker Sub foot

Torx at head

screws (for the top

brackets, 2 ea)

Ø4 X 8 screws

(2 ea)

Kick plate brackets

(2 ea)

Kick plate

Badge

(for modernist

model)

Badge

(for heritage model)

Installation kit (not provided)

Electrical tape &

Standard duct tape

Hot water line 90°Fitting (⁄") Tube ttings

Hose clamp Air gap Rubber connector Teon tape or

sealing compound

WARNING

Do not use plastic tubing. Plastic tubing can deteriorate over time and cause a leak inside

the tube tting.

DACOR_DW9500M_DD68-00197A-01_EN.indd 4 2017-08-23  8:54:50

Installation

English 5

NOTE

• For the hot water line, we strongly recommend using ⁄" minimum O.D. copper tubing

with a compression tting or a exible stainless steel braided hot water supply line.

• You also need a 90°Fitting with ⁄" N.P.T. external pipe threads on one end and a tting

sized to t your hot water line (copper tubing/compression tting or braided hose) on

the other.

• For the power cable, we recommend a jacketed grounded 12-2 cable. Note that some

local codes may require the cable to have a BX style metal jacket.

Tools required (not provided)

Electric drill Safety glasses Gloves Flashlight

Adjustable wrench Torx T20 Pliers Nipper

Tape measure Pencil Phillips screwdriver Flat head

screwdriver

Tubing cutter Cutting knife Level Hole saw

Hex L-wrench Vernier calipers Steel ruler

DACOR_DW9500M_DD68-00197A-01_EN.indd 5 2017-08-23  8:54:51

Installation

English6

Unpacking

Unpack the dishwasher in an open area free of obstruction. We recommend keeping all

the packing materials until the dishwasher is completely installed.

Kick plate

1. Position the carton right-side-up with

the top arrows pointing upwards.

2. Unbuckle or cut the straps securing the

packaging.

3. Unpack the product packaging with

care.

4. Inspect every component for any signs

of damage.

5. Locate and set aside the dishwasher's

kick plate. The kick plate is attached

beside of the dishwasher.

6. Lift the dishwasher from the packing

material, and then place it on the oor.

NOTE

• There are also packing materials inside the dishwasher. Leave them in place until the

dishwasher is installed.

• Do not remove the sound-absorbent padding that surrounds the exterior of the

dishwasher.

DACOR_DW9500M_DD68-00197A-01_EN.indd 6 2017-08-23  8:54:51

Installation

English 7

Installation requirements

To prevent a risk of re, electric shock, or

personal injury, all wiring and grounding

must be done by a qualied technician.

Power supply

• To prevent the risk of re, electric

shock, or personal injury, all wiring

and grounding must be performed in

accordance with the National Electrical

Code ANSI/FNPA, No. 70 Latest Revision

and local codes and ordinances. It is the

personal responsibility of the appliance

owner to provide adequate electrical

service for this appliance.

• When preparing for installation, make

sure that your power supply provides

an individual 120 Volt, 60 Hz branch

circuit serving only your dishwasher

with a 15 AMP fuse or circuit breaker.

• Your dishwasher must be grounded. If

your dishwasher malfunctions or breaks

down, grounding will reduce the risk of

electric shock by providing a path of

least resistance for the electric current.

WARNING

• Do not use an extension cord.

• Use only the power plug that comes

with the dishwasher.

Grounding

For permanent grounding, the dishwasher

must be properly grounded to a grounded

metal or permanent wiring system. The

grounding conductor must be run with

the circuit conductors and then connected

to the grounding terminal or lead on the

dishwasher.

WARNING

• Do not connect the ground wire to

plastic plumbing, gas lines, or hot water

pipes. Improperly connected grounding

conductors may cause electric shock.

• Do not modify the power plug of the

dishwasher. If the power plug does

not t the outlet, have a proper outlet

installed by a qualied electrician.

DACOR_DW9500M_DD68-00197A-01_EN.indd 7 2017-08-23  8:54:52

Installation

English8

Water supply

• The hot water supply line must support

water pressures between 20 psi and

120 psi (140-830 kPa).

• Water temperatures must be between

120 °F (49 °C)and 149 °F (65 °C).

To reduce a risk of leaks:

• Make sure water taps are easily

accessible.

• Turn the water tap off when the

dishwasher is not in use.

• Check for any leaks at the water hose

ttings on a regular basis.

Flooring

For safety, the dishwasher must be

installed on a solidly constructed oor.

Wooden oors may need to be reinforced

to minimize vibrations. Avoid installing

on carpet or soft tile. Carpeting and soft

tile may cause vibrations and may cause

your dishwasher to move slightly while

operating.

WARNING

Do not install the dishwasher on a poorly

supported structure.

DACOR_DW9500M_DD68-00197A-01_EN.indd 8 2017-08-23  8:54:52

Installation

English 9

Dimensions and specications

Dishwasher

DDW24M99* Series (Modernist)

23⁄" (598 mm)

32⁄"-34⁄" (820-880 mm)

2⁄" (67 mm)

2⁄" (70 mm)

20⁄" (520 mm)

22⁄" (580 mm)

Front view Side view

DDW24T99* Series (Heritage)

6" (152 mm)

2" (50 mm)

20⁄" (520 mm)

2⁄" (60 mm)

21⁄" (555 mm)

22⁄" (580 mm)

FBI model only

(DDW24T999BB/DA)

Front view Side view

DACOR_DW9500M_DD68-00197A-01_EN.indd 9 2017-08-23  8:54:52

Installation

English10

Cabinet

23⁄" (603.0 mm)

minimum

22⁄" (580 mm)

minimum

34⁄" - 34⁄" (874-886 mm)

• This dishwasher is designed to be

enclosed on the top and on both sides

by a standard, residential kitchen

cabinet.

• The installation enclosure must be clean

and free of any obstructions.

• The enclosure must be at least 23⁄"

inches wide, 22⁄" inches deep, and

34⁄" inches high.

• For the front door of the dishwasher to

be ush with the leading edge of the

countertop, the countertop must be at

least 23 inches deep.

Specications

Specications are subject to change without notice for improved quality. The actual

appearance of the dishwasher may differ from the illustrations in this manual.

Power supply 120 V, 15 A, 60 Hz AC

Water pressure 20 - 120 psi (140 - 830 kPa)

Dimensions

(Width x Depth x Height)

DDW24M999UM / DDW24M999US / DDW24T998US :

23⁄" X 22⁄" X 32⁄" (598 X 580 X 820 mm)

DDW24T999BB :

23

1

/2” X 21

7

/8 ” X 32

1

/4" (598 X 555 X 820 mm)

Minimum inlet water

temperature

120 °F (49 °C)

DACOR_DW9500M_DD68-00197A-01_EN.indd 10 2017-08-23  8:54:52

Installation

English 11

Step-by-step installation

The installation procedure may differ depending on the model.

STEP 1 Select a location

Select a location that meets the following conditions.

• The location must have a solid oor that can support the weight of the dishwasher.

• The location must be near a sink (9.8 ft/3 m) with easy access to the water supply,

drain system, and electrical outlet.

• The location must let you load dishes into the dishwasher easily.

• The location must have sufcient space for the dishwasher door to open easily

and provide enough space between the dishwasher and the cabinet sides (at least

0.1 inch/2 mm).

• The rear wall must be free of obstructions.

Installation in a new location

A

B

If you install the dishwasher in a new

location, follow these instructions before

installing the dishwasher.

1. Using a hole saw, cut a hole into the side

of the cabinet that holds the sink (A).

2. If the base inside the sink cabinet is raised

above the kitchen oor and is higher than

the connections on the dishwasher, make

a hole in the base inside the cabinet and in

the cabinet side (B).

NOTE

• If you are replacing an old dishwasher,

check the existing connections for

compatibility with the new dishwasher

and replace the connections as needed.

• You may need to cut a hole in the

opposite side of the cabinet according to

the location of the electrical outlet.

DACOR_DW9500M_DD68-00197A-01_EN.indd 11 2017-08-23  8:54:53

Installation

English12

3. Clean the bottom of the countertop.

4. Attach the protective sticker as shown.

DACOR_DW9500M_DD68-00197A-01_EN.indd 12 2017-08-23  8:54:53

Installation

English 13

STEP 2 Connect the hot water line

• The water line pressure must be between 20 psi and 120 psi (140–830 kPa).

• Make sure that the water temperature is delivered between 120 °F and 149 °F (49-

60 °C). Exceeding this limit may cause the dishwasher to malfunction.

• Make sure that the circuit breaker and water valve is turned off before connecting the

water supply line to the dishwasher.

• Make sure the water line is properly connected. Wrap Teon tape around every

connection and joint to prevent water leaks.

Inlet valve 90° elbow

tting

Hot water line

⁄" (5 mm)

Water valve

1. Insert the ⁄" 90-degree tting into the

inlet valve. Tighten the tting until it

points towards the water-hose channel

in the base of the dishwasher. Do not

overtighten.

2. Connect the hot water line to the tting.

3. If you want to secure the dishwasher

to the side wall for extra stability,

bend the brackets of the left and right

housings by referring to the gure.

DACOR_DW9500M_DD68-00197A-01_EN.indd 13 2017-08-23  8:54:53

Installation

English14

STEP 3 Arrange the hoses

1. Arrange the power cable and the drain

hose so that they move together.

2. Gently move the dishwasher to the

installation space under the sink. While

moving the dishwasher, pull any excess

portions of the water line, drain hose,

and power cable into the space.

NOTE

For DDW24M99** models, go to Step 6.

CAUTION

Use caution not to kink or step on the

power plug or the hoses.

DACOR_DW9500M_DD68-00197A-01_EN.indd 14 2017-08-23  8:54:53

Installation

English 15

STEP 4 Install the custom panel (FBI models only (DDW24T999BB/DA))

A

1. Insert the supplied rubber skirt (A) into

the 3 holes at the bottom of the door.

Ø 2

10-12

2. Put the installation template on the

back of the custom panel and x it

temporarily using transparent tape.

Note that the rear of the custom panel

will be attached to the dishwasher door.

CAUTION

• The top end of the custom panel must

be aligned with the top end of the

installation template.

• Use a custom panel between 7 lbs and

20 lbs.

3. Pre-drill the 6 points marked on the

installation template using a 2-pi drill

bit to a depth of 10 -12 mm.

B

C

B

C

4. Remove the installation template and

tighten the custom panel xers (B) at

the top with 2 screws (C, Ø4 X 20) as

shown.

DACOR_DW9500M_DD68-00197A-01_EN.indd 15 2017-08-23  8:54:54

Installation

English16

B

A

5. While holding the custom panel, attach

it to the door and insert the custom

panel xers (B) into the corresponding

holes at the top of the door as shown.

6. Push the custom panel downward to

x.

7. Cut the rubber skirt (A) using a cutting

knife so that it is aligned with the

front line of the dishwasher, which is

represented as a dashed line.

11-13 lbs (5-6 kg)

0-11 lbs (0-5 kg)

13-15 lbs (6-7 kg)

15-16.5 lbs (7-7.5 kg)

16.5-20 lbs (7.5-9 kg)

8. Pull out the dishwasher from the

cabinet, and then adjust the spring

screw on the upper-right side of the

dishwasher according to the weight

of the custom panel. Refer to the table

below.

Recommended spring levels

Level Weight of the custom panel

Level 1 0-11 lbs (0-5 kg)

Level 2 11-13 lbs (5-6 kg)

Level 3 13-15 lbs (6-7 kg)

Level 4 15-16.5 lbs (7-7.5 kg)

Level 5 16.5-20 lbs (7.5-9 kg)

DACOR_DW9500M_DD68-00197A-01_EN.indd 16 2017-08-23  8:54:54

Installation

English 17

9. Open the door and remove the

2 screws in the middle of the door.

CAUTION

Use caution when opening the door. The

door might open or close unexpectedly

if the spring level is not adjusted

appropriately, resulting in physical injury.

10. Secure the custom panel to the door by

fastening the 4 screws (Ø4 X 43).

DACOR_DW9500M_DD68-00197A-01_EN.indd 17 2017-08-23  8:54:54

Installation

English18

STEP 5 Install the door handle (DDW24T998US/DA only)

Blocking (X) Non-Blocking (O)

11-13 lbs (5-6 kg)

0-11 lbs (0-5 kg)

13-15 lbs (6-7 kg)

15-16.5 lbs (7-7.5 kg)

16.5-20 lbs (7.5-9 kg)

1. Loosen the hex nuts on the bar handle

if they are blocking the circle holes.

NOTE

Before installing the door handle, pull out

the dishwasher from the cabinet and check

if the spring level is set on 4.

2. Fit the bar handle into the 2 handle

bolts on the door. Make sure the nut

side of the handle faces downwards.

3. Tighten the hex nuts through the holes

on both sides of the handle using the

hex wrench.

4. Grab and move the bar handle slightly

to check if the handle is xed properly.

DACOR_DW9500M_DD68-00197A-01_EN.indd 18 2017-08-23  8:54:55

Installation

English 19

Checkpoints

A

B B

C

Bar handle / Outer door

(Tools: Vernier callipers, steel ruler)

Explanation Gap

A Left/Right 2" (50.5 mm)

B Up/Down 3⁄" (91.8 mm)

C All 0" (0.1 mm)

STEP 6 Attach the badge

9⁄" (242 mm)

2⁄" (54 mm)

DDW24M99* Series (Modernist)

Attach the badge to the dishwasher’s door

as shown.

9⁄" (244 mm)

2⁄" (59 mm)

DDW24T99* Series (Heritage)

DACOR_DW9500M_DD68-00197A-01_EN.indd 19 2017-08-23  8:54:55

Installation

English20

STEP 7 Level the dishwasher

0-1⁄" (0-45 mm)

1⁄"-2⁄" (45-60 mm)

Normal

Tall-kitchen

You can adjust the height of the

dishwasher to level it. Note that in these

steps, the dishwasher is currently inserted

halfway.

1. Use the level to check if the dishwasher

is level.

2. To adjust the front height, use the

normal sub foot for less than a 1⁄"

height, or the tall-kitchen sub foot for

heights between 1⁄" and 2⁄".

• To lower the height, turn the foot

clockwise.

• To raise the height, turn the foot

counter clockwise.

3. To adjust the rear height, insert the

Torx T20 screwdriver in the bottom

center of the dishwasher.

• To lower the height, turn the

screwdriver clockwise.

• To raise the height, turn the

screwdriver counter clockwise.

Min.

⁄"

(5 mm)

4. Leave at least a ⁄" space between the

top of the dishwasher and the bottom

of the countertop.

5. When levelling is complete, check if the

door opens and closes properly.

DACOR_DW9500M_DD68-00197A-01_EN.indd 20 2017-08-23  8:54:55

La page charge ...

Dacor DDW24M999UM Guide d'installation

Ce manuel convient également à

Dacor DDW24M999UM Guide d'installation

dans d''autres langues

Autres documents