Maytag MDB6949SDM0 Le manuel du propriétaire

Marque: Maytag

Modèle: MDB6949SDM0

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

THANK YOU for purchasing this high-quality product. Register your new dishwasher at www.maytag.com. In Canada, visit our

website at www.maytag.ca.

For future reference please make a note of your product model and serial numbers. These can be located near the door on the right-hand

or left-hand side of the dishwasher interior.

Model Number Serial Number

TableofContents

DISHWASHER SAFETY ............................................................. 1

QUICK STEPS ............................................................................ 3

DISHWASHER USE .................................................................... 3

CYCLE AND OPTION DESCRIPTIONS .................................... 6

DISHWASHER FEEDBACK SECTION ...................................... 7

DISHWASHER FEATURES ........................................................ 8

DISHWASHER CARE ................................................................. 9

TROUBLESHOOTING ................................................................ 9

WAR RANTY .............................................................................. 12

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

W10599489A

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: When using the dishwasher, follow basic precautions, including the following:

[] Read all instructions before using the dishwasher. [] Do not tamper with controls.

[] Use the dishwasher only for its intended function.

[] Use only detergents or rinse agents recommended for use in

a dishwasher, and keep them out of the reach of children.

[] When loading items to be washed:

1) Locate sharp items so that they are not likely to damage

the door seal; and

2) Load sharp knives with the handles up to reduce the risk

of cut-type injuries.

[] Do not wash plastic items unless they are marked

"dishwasher safe" or the equivalent. For plastic items not so

marked, check the manufacturer's recommendations.

[] Do not touch the heating element during or immediately after

use.

[] Do not operate the dishwasher unless all enclosure panels

are properly in place.

[] Do not abuse, sit on, or stand on the door, lid, or dish racks

of the dishwasher.

[] To reduce the risk of injury, do not allow children to play in

or on the dishwasher.

[] Under certain conditions, hydrogen gas may be produced in

a hot water system that has not been used for two weeks or

more. HYDROGEN GAS IS EXPLOSIVE. If the hot water

system has not been used for such a period, before using

the dishwasher turn on all hot water faucets and let the

water flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is flammable,

do not smoke or use an open flame during this time.

[] Remove the door or lid to the washing compartment

when removing an old dishwasher from service or

discarding it.

SAVE THESE iNSTRUCTiONS

GROUNDING iNSTRUCTiONS

For a grounded, cord-connected dishwasher:

The dishwasher must be grounded. In the event of a

malfunction or breakdown, grounding will reduce the risk of

electric shock by providing a path of least resistance for

electric current. The dishwasher is equipped with a cord

having an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet

that is installed and grounded in accordance with all local

codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

[]

Check with a qualified electrician or service representative

if you are in doubt whether the dishwasher is properly

grounded. Do not modify the plug provided with the

dishwasher; if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

For a permanently connected dishwasher:

The dishwasher must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the dishwasher.

SAVE THESE iNSTRUCTiONS

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

Prepare and load _f'_

dishwasher. _

Select a cycle and option (cycles and options vary

by model).

PowerBIast auto normal quick rinse

0000 90

cycles delay

hiternp sanitize heated dry

0 0 0 0 0

controlIock canc_| start

hold 3 sec drain resume

A B

The full lit display will glow for Wash(A), Dry(B),

Lock(C), and Sanitized or Clean.

Start dishwasher.

CZ/

start

reslrne

10 Placeloading pattern

Prepare and Load the Dishwasher

IMPORTANT: Remove leftover food, bones, toothpicks and other

hard items from the dishes. Remove labels from containers before

washing.

8 Place loading pattern

,,_J/ _. :\ ,'Wt_ #< f-_+i

Upper rack Lower rack

12 Place loading pattern

Upper rack Lower rack

Make sure nothing keeps spray arm(s) from

spinning freely. It is important for the water

spray to reach all soiled surfaces.

Make sure that when the dishwasher door is closed no items

are blocking the detergent dispenser.

Items should be loaded with soiled surfaces facing down and

inward to the spray as shown. This will improve cleaning and

drying results.

Avoid overlapping items like bowls or plates that may trap food.

Place plastics, small plates and glasses in the upper rack.

Wash only plastic items marked "dishwasher safe."

To avoid thumping/clattering noises during operation: Load

dishes so they do not touch one another. Make sure lightweight

load items are secured in the racks.

When loading silverware, always place sharp

items pointing down. Mix other items

pointing up and some pointing down.

STEP2

Add Detergent

NOTE: If you do not plan to run a wash cycle soon, run a rinse

cycle. Do not use detergent.

• Use automatic dishwasher detergent only. Add powder, liquid

or tablet detergent just before starting a cycle.

• Fresh automatic

dishwasher

detergent results

in better

cleaning. Store

tightly closed

detergent

container in a

cool, dry place.

For optimum

performance,

tablet detergent

is recommended.

A. Cover latch

B. Main wash section

C. Pre-wash section

Premeasured Detergents

Many detergents now come in premeasured forms (gel packs,

tablets, or powder packs). These forms are suitable for all hardness

and soil levels. Always place premeasured detergents in the main

compartment and close the lid.

Using dishwasher detergent tablets and packs have been proven

better than powder, liquid or gel detergents to reduce filming on the

dishes. By using these tablets and packs, over time this will start to

reduce or eliminate white film. Also, by using a rinse aid you can

minimize repeat buildup of white film.

Powder and Gels

NOTE: Fill amounts shown

are for standard powdered

detergent. Follow instructions

on the package when using

other dishwasher detergent.

• The amount of detergent to use depends on:

How much soil remains on the items - Heavily soiled loads

require more detergent.

The hardness of the water - If you use too little in hard water,

dishes won't be clean. If you use too much in soft water,

glassware will etch.

Soft to Medium Water (0-6 grains per U.S. gallon)

[typical water softener water and some city water]

Medium to Hard Water (7-12 grains per U.S. gallon)

[well water and some city water]

• Depending on the water hardness, fill the Main Wash section of

the dispenser as shown.

X Hard Water iL_

Soft Water

Add Rinse Aid

The dishwasher is designed to use rinse aid for good drying

performance. Without rinse aid the dishes and dishwasher

interior will have excessive moisture. The heat dry option will

not perform as well without rinse aid.

Rinse aid keeps water from forming droplets that can

dry as spots or streaks. They also improve drying by

allowing water to drain off of the dishes after the final

rinse.

Rinse aid helps to reduce excess moisture on the

dish racks and interior of the dishwasher.

Full

Add

Check the rinse aid indicator. Add rinse aid when indicator

drops to "Add" level.

To add rinse aid, turn the

dispenser cap 1Aturn

counterclockwise and lift

off. Pour rinse aid into the

opening until the indicator

level is at "Full." Replace

the dispenser cap and turn

to "Lock." Make sure cap

is fully locked.

USERINSEAIDFOR Full

BETTERDRYING

Lock

Add

1/4turn to lock

NOTE: For most water

conditions, the factory

setting of 2 will give good

results. If you have hard

water or notice rings or

spots, try a higher setting.

Turn the arrow adjuster

inside the dispenser by either

using your fingers or

inserting a flat-blade screwdriver into the center of the arrow and

turning.

Select a Cycle (cycles vary by model)

Efficient dishwashers run longer to save water and energy, just as

driving a car slower saves gas. Cycle times may increase or

decrease depending on selections. Estimated cycle times after

calibration are listed in the "Cycle and Options Descriptions" chart

in the following section. Select the desired cycle by pressing the

CYCLES button. Each time you press the Cycles button it will

advance to the next available cycle.

PowerBIast auto normal quick rinse

9000 9 o

cycles delay

Select Options (options vary by model)

See "Cycle and Option Descriptions" charts in the following

section.

You can customize the cycles by pressing the options desired and

pressing Start/Resume.

hitemp sanitize heated dry

0 0 0 0 0

{ { { { {

controllock cancel slat[

ho(d 3sec drain resume

Follow the Progress of the Dishwasher.

Depending on the model, progress will be displayed by a full lit

display or by an indicator light on the front panel.

The full lit display will glow for Wash(A), C

Dry(B), Lock(C), Sanitized, or Clean. It

will also show the estimated remaining

time for the cycle in hours and minutes.

When delay is selected, the full lit

display will show an "h" for hour and the

number of hours to delay.

The indicator light will glow blue for

wash, red for dry, or green for cycle

complete.

A B

Start or Resume a Cycle

• Run hot water at the sink nearest your dishwasher until the

water is hot. Turn off water.

Push door firmly closed. The door latches

automatically. Select the wash cycle and options ©

desired and press START/RESUME or press

START/RESUME to repeat the same cycle and

start

options as in the previous wash cycle. _.....

You can add an item anytime before the main wash

starts. Open the door slowly and add the item.

Close the door firmly. Press the START/RESUME button. The

cycle resumes automatically at the point of interruption.

For fully integrated models (controls on top of console)

• Select the wash cycle and options desired.

• Press the START/RESUME button once and close the door.

After a brief pause, the cycle will begin. The door must be

closed within 4 seconds after pushing START/RESUME or the

lights will flash, and the dishwasher will not begin. Press the

START/RESUME button again and shut the door within

4 seconds.

You can add an item anytime before the main wash starts. Open

the door slowly and add the item. Press the START/RESUME then

close the door within 4 seconds.

PowerBlast auto normal quick rinse hitemp sanitize heated dry

o00090 o o o o o

cycles delay cootro,ock cancel start

hold 3 sec drain resume

This information covers several different models. Your dishwasher may not have all of the cycles and options described.

CYCLES ESTIMATED WATER

WASH TIME USAGE

DISPLAYED GALLONS

(LITERS)

Targets toUghest food Soi!sl use for hard4o-clean heavily soi!ed pots, pans, 3:28 9.0 (34.0)

casseroles, and tableware.

PowerB[ast TM

auto

Load and soil sensing cycle. This cycle is optimized to achieve best cleaning with

minimal water and energy for all soil levels.

2:03 4.5 (I 6.9)

ThisCyCle Wth only the Heated Dry option selected and Without other options 1:51 3.8 (14.5)

selected, is recommended to completely wash and dry a fu!! load o{ normally soiled

normal

O .......dishes. The energy usage labe! is based Onthis cYCle and option combination I ............................................................

For fast results, this cycle will clean light to medium soiled dishes, but use slightly

more water and energy. For improved drying, select heated dry option.

:59 5.5 (20.9)

quick

use for rinsing dishesl glasses, and Silverware that wi!l not be washed right away, :!! 1:3(4.9)

rinse • • • •

o DO not use detergent. Dunng cycle, the rinse actJ0n w!!! repeatedly pause for several

seconds.

Cycle times may increase depending on water temperature, heavy soil condition, dish load size and options selected.

*Adding options will add time to cycle. See options information.

OPTIONS CAN BE WHAT IT DOES ADDEDTIME ADDED

SELECTED TO CYCLE WATER

WITH GALLONS

(LITERS)

Runs dishwasher at a later time or dudng off.peak Available with DelaYs start of a NA NA

0 electrical hours. Se!ect a wash cycle and options, any cycle cycle up to

Press Delay one time for each additional hour of 24 hours

_i_ delay up to 24 h0urs. Press START/RESUME. Close

door firmly. ....

NOTE: Anytime door is opened (such as, to add a

dish), START/RESUME button must be pressed

again to resume delay countdown.

Raises main wash temperature to improve cleaning Auto Raises main wash :04 to 1:16 0-1.2

hitemp for loads containing tough, baked-on food. PowerBlastTM temperature from (0-4.5)

O 105°F (41°C) to

Normal 129OF(54oC).

sanitizes dishes and g!assware by raising water Auto Increased to 1:15 0-3.0

_anitiZe temperature in final rinse: ln accordance with NSF/ PoWerBlastTM wash temperature tO 11 21

O o o I •

ANSI Standard 184 for Residentia! Uishwashersl Normal from 105 F(41 C)

Certified residential dishwashers are not intended for to 1451F (630C)and

licensed food establishments This option will add final rinse from

_o t olloc , ' o o

"°d3*_ heat and t!me to cycle: 140 F (60 C) to

At end 0f the cycle the Sanitized indicator (or W0rd !56°E (69!c) '

c "sanitized,' on some models) will glow. Ifthe load did

not properly sanitize, the indicator will flash at the

end of the cycle. This can happen if cycle is

B interrupted, or if the water does not reach the

required temperature. The light goes off when you

open and close the door or press CANCEL

OPTIONS CAN BE WHAT IT DOES ADDED TIME ADDED

SELECTED TO CYCLE WATER

WITH GALLONS

(LITERS)

heated dry

Dries dishes with heat. Use option with rinse aid to

provide best drying results. Plastic items are less

likely to deform when loaded in top rack. Turn option

off for an air dry.

Auto Uses heating

PowerBlastTM element to speed

drying times.

Normal

Quick

:29 to :46

CONTROL PURPOSE COMMENTS

Press to start o[ resume a If the door is opened during a CYcleor power is interrupted, Start/Resume indicator

0 wash cycle flashes. Cycle will not resume until door is closed and Start/Resume is pressed,

NOTE: IfSTART/RESUME button is lOCated on top of d0ori PUsh door firmly CloSed

start within 4 seconds of pressing START/RESUME. If door is not closed within 4 seconds,

resume . , .

start button LED wJ fash, an audJb e tone wJ be heard (on some top contro mode s),

and cycle will not start.

Press to cancel wash cycle Close door firmly. The dishwasher starts a 3-minute drain (if needed). Let dishwasher

k J

cancel

drain

O .... control Lock avoids To turn on Lock press and hold CONTROL LOCK or SANITIZE (depending on model)

r_ unintended useo{ for 3 seconds:Control Lock !ight will stay on for a short time;indicating that it is

. dishwasher between cycles activated and a !buttons are disabled, !f you press any button while the dishwasher is

ca,ce[ orcycleand opton changes locked, light flashes 3times, Dishwasher door can stil be opened!closed while

_'" during a cycle, controls are ocked.

c Toturn off Lock press and hold CONTROL LOCK or SANITIZE (depending on model)

for 3 secondsl Light turns off.

NOTE: If the model requires you to press and ho!d Sanitize to !ock controls, Control

_ Locked LED(C) will be on or off to indicate whether Control Lock is active or not,

CONTROL PURPOSE COMMENTS

Tofo,owtheprogressDependingonthemode ,progress bed sp ayedbyafu,Utd sp ayorbyan nd cator

c of the dishwasher light on the front panel

I_ cycle

The full iit disp!aY Wil! glow for wash (A), D_(B)' sanitiZed orCieanl !t will a!so showthe

estimated rernaining time for the cYCle.

O The indicator light Will glow blue for Wash; red for dry, and green for Cyc!e complete:

Canceling A Cycle

1. Open the door slightly to stop the cycle. Wait for the spraying

action to stop before completely opening the door.

2. Press CANCEL/DRAIN button once. The Cancel/Drain light will

light up.

3. Close the door, and the dishwasher starts a drain cycle (if

water remains in bottom of dishwasher). Let the dishwasher

drain completely. The Cancel/Drain light turns off after

3 minutes.

Changing A Cycle After Dishwasher Is Started

1. You can interrupt a cycle and restart the dishwasher from the

beginning using the following procedure.

2. Open the door slightly to stop the cycle. Wait for the spraying

action to stop, then open the door completely.

3. Check that detergent dispenser cover is still closed. If cover is

open, you will need to refill the detergent dispenser before

restarting the new cycle.

4. Press CANCEL!DRAIN twice to reset the control.

5. Select new cycles and options.

6. Press START/RESUME.

Adding A Dish After Dishwasher Is Started

1. Check if Add a Dish indicator is lit. (Available on some models.

Otherwise, proceed to Step 2.)

2. Open the door slightly to stop the cycle. Wait for the spraying

action to stop, then open the door completely.

3. Check whether the detergent dispenser cover is still closed. If

it is open, the wash cycle has already started and adding a

dish is not recommended.

4. If detergent has not yet been used (detergent dispenser cover

is closed), you may add a dish.

5. Press START/RESUME.

_/;_,. / _/_S_ _ _,_@

Your Maytag dishwasher may have some or all of these features.

Silverware Basket

Use suggested loading patterns, as shown, to better clean the

silverware.

10 place leading pattern

Use the slots in the cover to keep the silverware separated for

optimum wash.

If the silverware does not fit into the designated slots, slide the

covers outward to remove them and mix silverware types to keep

them separated.

Load knives down, forks up, and alternate spoons for best cleaning

results.

Folding Tines

The Folding Tines located in the back

left corner (lower rack) provide

convenient loading space for large,

bulky items such as pots, pans and

mixing bowls.

To lower the tines:

Gently push the tines out of each holder

toward the center and lay the tines

down.

Cup Clips

The Cup Clips located in the upper rack can be

used to hold lightweight plastic items, cooking

utensils and knives in place. Clip the item between

the tine and the clip.

Stack-Rack Shelves

Increase loading flexibility - items

such as casserole dishes stay

stable while the folding shelf allows

you to load smaller items on top.

Cup Shelf

Fold down the extra shelf on the left-hand or

right-hand side of the top rack to hold

additional cups, stemware, or long items

such as utensils and spatulas.

Adjustable Upper Racks

The Adjustable Upper Rack and can be raised or lowered to

accommodate taller plates, platters, pots or pans, in the upper or

lower racks. Full size dinner plates can be loaded in the upper rack

if it is in the lower position.

NOTE: Always unload racks before adjusting.

To raise the rack, press both

rack adjusters and lift the rack

until it is in the up position

and level.

To lower the rack, press both

rack adjusters and slide the

rack back to its lower

position.

Removable Upper Rack

The removable rack allows you to wash larger items such as stock

pots, roasters, and cookie sheets in the lower level rack.

IMPORTANT: Remove dishes prior to removing the upper rack

from the dishwasher.

To remove the rack (push tab rack stop):

1. Roll the rack V3to V2of the way

out of the tub.

2. Rotate the rack stops outward.

3. Roll the rack all the way out of

the track and remove from the

dishwasher.

To replace the rack:

Reverse the above steps 1-3 to

replace the rack into the

dishwasher.

Sshwast, e ....

CLEANING THE DISHWASHER

Cleaning the exterior

Clean the exterior of the dishwasher with a soft, damp cloth and

mild detergent. If the dishwasher has a stainless steel exterior, a

stainless steel cleaner is recommended - Stainless Steel Cleaner

and Polish Part Number 31464.

Cleaning the interior

Clean the interior of the dishwasher, with a paste of powdered

dishwasher detergent and water or use liquid dishwasher detergent

on a damp sponge to clean the cooled-down interior.

A white vinegar rinse may remove white spots and film. Vinegar is

an acid, and using it too often could damage the dishwasher.

Put 2 cups (500 mL) white vinegar in a glass or dishwasher-safe

measuring cup on the bottom rack. Run the dishwasher through a

complete washing cycle using an air-dry or an energy-saving dry

option. Do not use detergent. Vinegar will mix with the wash water.

Dishwasher Maintenance Procedure

Removal of Hard Water / Filming: Recommended use of a

monthly maintenance product such as affresh®t Dishwasher

Cleaner Part Number W10282479.

• Load the dishwasher (preferably with dishes affected by

filming/hard water).

• Place tablet in main wash compartment of detergent dispenser.

• Select cycle/option best for heavily soiled dishes and start

dishwasher.

NOTE: It is recommended to use a premeasured detergent tablet

or pack for regular daily use.

t® affresh is a registered trademark of Whirlpool, U.S.A.

Drain air gap

If you have a drain air gap,

check and clean it if the

dishwasher isn't draining

well.

To Reduce Risk of Property Damage During Vacation or

Extended Time Without Use

• When you will not be using the dishwasher during the summer

months, turn off the water and power supply to the dishwasher.

• Make sure the water supply lines are protected against freezing

conditions. Ice formations in the supply lines can increase

water pressure and cause damage to the dishwasher or home.

Damage from freezing is not covered by the warranty.

• When storing the dishwasher in the winter, avoid water damage

by having the dishwasher winterized by authorized service

personnel.

First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,

refer to the warranty page in this manual and scan the code with your mobile device, or visit www.maytag.com/product_help.

In Canada, visit www.maytag.ca.

In the U.S.A.:

Maytag Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in the correspondence.

In Canada:

Maytag Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

PROBLEM SOLUTION

DISHWASHER DOES

NOT RUN

DETERGENT REMAINS IN THE

DISPENSER OR

TABLET IS ON BOTTOM

OFTUB

NOTE: It is normal for the dishwasher to repeatedly pause several times during a cycle.

If the START/RESUME light is blinking, press START/RESUME and close the door firmly within

4 seconds.

Press and hold HI TEMP WASH for 3 seconds to turn the audible tones on or off.

Be sure the door is closed and latched.

Be sure you have selected a cycle. See "Cycles and Options Descriptions."

Be sure there is power to the dishwasher. A circuit breaker or fuse might have tripped.

If lights other than Start/Resume blink and the unit will not run, you will need to call for service.

Check for dishware such as cookie sheets, cutting boards, or large containers, etc., that may be

blocking the detergent dispenser from opening properly.

Be sure the detergent is fresh and lump free.

Be sure the cycle has been completed (green light is on). If it has not been completed, you will need

to resume the cycle by pressing START/RESUME and closing the door within 4 seconds.

CYCLERUNSTOO LONG

DISHWASHER NOT DRYING

WILL NOT FILL

NOTES:

• Efficient dishwashers run longer to save water and energy. Cycle times may increase depending

on selections (See "Cycles and Options Descriptions" for estimated cycle times.)

• A water heater setting of 120°F (49°C) is best. The dishwasher will delay longer while heating

cooler water.

Try the Quick Wash cycle.

Run the hot water at a faucet close to the dishwasher before starting the cycle.

NOTE: Plastic and items with nonstick surfaces are difficult to dry because they have a porous

surface, which tends to collect water droplets. Towel drying may be necessary.

Use of rinse aid along with the Heated Dry and Sanitize option will provide the best drying and avoid

excess moisture in the dishwasher interior.

Proper loading of items can affect drying. (See specific loading instructions within this guide.)

Glasses and cups with concave bottoms hold water. This water may spill onto other items when

unloading.

• Unload the bottom rack first.

• Place these items on the more slanted side of the rack for improved results.

Be sure the water is turned on to the dishwasher.

Check that the float is free from obstructions.

Check for suds in the dishwasher. Iffoam or suds are detected, the dishwasher

may not operate properly or may not fill with water.

Be sure the cycle has been completed (the green light is on). Ifthe cycle has not been completed, you

will need to resume the cycle by pressing START/RESUME and closing the door within 4 seconds.

If dishwasher is connected to a food waste disposer, be sure the knockout plug has been removed

from the disposer inlet.

Check for kinks in the drain hose.

Check for food obstructions in the drain or garbage disposer.

Check the house fuse or circuit breaker.

NOTE: Extremely hard water mineral deposits can cause damage to the dishwasher and make it

difficult to achieve good cleaning. A water softener is strongly recommended if the hardness is

15 grains or more. If a water softener is not installed, the following steps may help:

Use a commercial cleaner designed for dishwashers once per month.

Always use a rinse aid.

Always use a high-quality, fresh detergent.

Use a detergent booster/water softener additive designed for dishwashers.

NOTE: If the dishwasher is not used daily, you can run a rinse cycle with the partial load until a full

load is ready to run.

Run a vinegar rinse through the dishwasher by putting 2 cups (500 mL) of white vinegar in an upright

glass measuring cup in the lower rack. Run a normal cycle with the Heated Dry option turned off. Do

not use detergent.

The dishwasher may not be draining properly, see "WATER REMAINS IN THE TUB/WILL NOT DRAIN"

in "Troubleshooting."

NOTES:

• Surging sounds can occur periodically throughout the cycle while the dishwasher is draining.

• Normal water valve hissing may be heard periodically.

• A normal snap sound may be heard when the detergent dispenser opens during the cycle and

when the door is opened at the end of the cycle.

• Improper installation will affect noise levels.

Be sure the filters are properly installed.

A thumping sound may be heard if items extend beyond the racks and interfere with the wash arms.

Readjust the dishware and resume the cycle.

WATER REMAINS IN THE TUB/

WILL NOT DRAIN

HARD WATER

(WHITE RESIDUE ON

DISHWASHER INTERIOR OR

GLASSWAR E)

ODORS

NOISY

PROBLEM SOLUTION

FOOD SOILS REMAIN

ON DISHES

Be sure the dishwasher is loaded correctly. Improper loading can greatly decrease the washing

performance. See "Prepare and Load the Dishwasher" in the "Dishwasher Use" section.

Select the proper cycle and option for the type of soils. PowerBlast TM with the Sanitize option can be

used for tougher loads.

Be sure the incoming water temperature is at least 120°F (49°C).

Use the proper amount of fresh detergent. More detergent is needed for heavier-soiled loads and

hard water conditions.

Scrape food from dishes prior to loading (do not prerinse).

DID NOT SANITIZE If the sanitized light is blinking, the load is NOT sanitized. The cycle was interrupted in the final rinse,

or the water heater is set too low. Set the water heater to 120°F (49°C).

DAMAGE TO DISHWARE Improper loading can cause dishes to become chipped or damaged. See specific loading instructions

within this guide.

BLINKING LIGHTS If the START/RESUME light is blinking, press START/RESUME and close the door within 4 seconds.

If the Clean light or any other lights are blinking and the dishwasher will not run, call for service.

CLOUDY OR SPOTTED

DISHWARE (AND HARD

WATER SOLUTION)

NOTES:

• Liquid rinse aid is necessary for drying and to reduce spotting.

• Use the correct amount of detergent.

Confirm that the cloudiness is removable by soaking the item in white vinegar for 5 minutes. Ifthe

cloudiness disappears, it is due to hard water. Adjust the amount of detergent and rinse aid. See

"HARD WATER (WHITE RESIDUE ON DISHWASHER INTERIOR OR GLASSWARE)" in the

"Troubleshooting" section. If it does not come clear, it is due to etching (see below).

Be sure the incoming water temperature is set at 120°F (49°C).

Try using the Hi Temp and Sani Rinse options.

To remove spotting, run a vinegar rinse through the dishwasher.

• Wash and rinse the affected dishware and load into dishwasher. Remove all silverware and metal

items. Put 2 cups (500 mL) of white vinegar in a glass measuring cup in the lower rack. Run a

normal cycle with the Heated Dry option turned off. No detergent is needed.

ETCHING (PERMANENT

CLOUDINESS)

This is an erosion of the surface of the glassware and can be caused by a combination of: water that

is too hot, from using too much detergent with soft water or by pre-washing. Detergent needs food

soil to act upon. If etching has occurred, the glassware is permanently damaged. To avoid further

etching, adjust the detergent amount to match the water hardness, stop pre-washing, and use water

heating options only when incoming water temperature is below 120°F (49°C).

LEAKING WATER

Be sure dishwasher has been installed properly and is level.

Suds can cause the dishwasher to overflow. Measure the detergent accurately and use only

detergents designed for use in a dishwasher. Less detergent is needed in soft water. Try another

brand of detergent if sudsing continues.

To avoid rinse aid leaking from the dispenser, be sure the lid is securely attached and avoid overfilling.

TUB IS DISCOLORED NOTES:

• High iron content in the water can discolor the tub.

• Tomato-based foods can discolor the tub or dishware.

A citrus-based cleaner can be used to clean.

MAYTAG ®DISHWASHER

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED

TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the Customer

eXperience Center:

• Name, address and telephone number

• Model number and serial number

• A clear, detailed description of the problem

• Proof of purchase including dealer or retailer name and address

IF YOU NEED SERVICE:

[]

1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions

can be addressed without service. Please take a few minutes to review the Troubleshooting or Problem Solver

section of the Use and Care Guide, scan the QR code on the right to access additional resources, or visit https:/

/www.maytag.com/prod uct_help. ==

2. All warranty service is provided exclusively by our authorized Maytag Service Providers. In the U.S. and

Canada, direct all requests for warranty service to:

Maytag Customer eXperience Center https://www.maytag.com/

In the U.S.A., call 1-800-688-9900. In Canada, call 1-800-807-6777. producthelp

If outside the 50 United States or Canada, contact your authorized Maytag dealer to determine whether another warranty applies.

FIRST YEAR LIMITED WARRANTY (PARTS AND LABOR) 1.

For one year from the date of purchase, when this major appliance is

installed, operated and maintained according to instructions attached 2.

to or furnished with the product, Maytag brand of Whirlpool 3.

Corporation or Whirlpool Canada, LP (hereafter "Maytag") will pay for

factory specified replacement parts and repair labor to correct defects

in materials or workmanship that existed when this major appliance

was purchased, or at its sole discretion replace the product. In the

event of product replacement, your appliance will be warranted for the 4.

remaining term of the original unit's warranty period. 5.

SECOND THROUGH TENTH YEAR LIMITED WARRANTY

(CERTAIN COMPONENT PARTS ONLY - LABOR NOT INCLUDED)

In the second through tenth years from the date of original purchase,

when this major appliance is installed, operated and maintained

according to instructions attached to or furnished with the product,

Maytag will pay for factory specified parts for the following

components to correct non-cosmetic defects in materials or

workmanship in these parts that prevent function of this major

appliance and that existed when this major appliance was purchased.

This is a limited 10-year warranty on the below named parts only and

does not include repair labor.

• Upper and Lower Racks (excludes cup shelves and silverware

basket)

• Chopper Blade

• Stainless Steel Tub and Inner Door Liner

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

Service must be provided by a Maytag designated service company.

This limited warranty is valid only in the United States or Canada and

Commercial, non-residential or multiple-family use, or use inconsistent

with published user, operator or installation instructions.

In-home Instruction on how to use your product

Service to correct improper product maintenance or installation,

installation not in accordance with electrical or plumbing codes or

correction of household electrical or plumbing (i.e. house wiring, fuses

or water inlet hoses).

Consumable parts (i.e. light bulbs, batteries, air or water filters, etc.).

Damage from accident, misuse, abuse, fire, floods, acts of God or use

with products not approved by Maytag.

6. Repairs to parts or systems to correct product damage or defects

caused by unauthorized service, alteration or modification of the

appliance.

7. Cosmetic damage including scratches, dents, chips, and other damage

to appliance finishes unless such damage results from defects in

materials and workmanship and is reported to Maytag within 30 days.

8. Discoloration, rust or oxidation of surfaces resulting from caustic or

corrosive environments including but not limited to high salt

concentrations, high moisture or humidity or exposure to chemicals.

9. Pick-up or delivery. This product is intended for in-home repair.

10. Travel or transportation expenses for service in remote locations where

an authorized Maytag servicer is not available.

11. Removal or reinstallation of inaccessible appliances or built-in fixtures

(i.e. trim, decorative panels, flooring, cabinetry, islands, countertops,

drywall, etc.) that interfere with servicing, removal or replacement of the

product.

12. Service or parts for appliances with original model/serial numbers

removed, altered or not easily determined.

applies only when the major appliance is used in the country in which it The cost of repair or replacement under these excluded circumstances

was purchased. This limited warranty is effective from the date of shall be borne by the customer.

original consumer purchase. Proof of original purchase date is required

to obtain service under this limited warranty.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow

limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you

specific legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Maytag makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations

contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance,

you should ask Maytag or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. MAYTAG

SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation

of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and

you also may have other rights that vary from state to state or province to province.

2/14

4/14

LEAGRADECEMOS la compra de este producto de alta calidad. Registre su nuevo lavavajillasen www.maytag.com. En CanadA,

registre su lavavajillas en www.maytag.ca.

Para referencia futura, tome nota del nQmerode modelo y de serie del producto. Los puede encontrar cerca de la puerta en el lado

derecho o izquierdo del interior de la lavavajillas

NQmerode modelo NQmero de serie

Indice

SEGURIDAD DE LA LAVAVAJILLAS ..................................... 13

PASOS RAPI DOS ..................................................................... 15

USO DE LA LAVAVAJILLAS .................................................... 15

DESCRIPCION DE CICLOS Y OPCIONES ............................. 18

SECCION DE INFORMACION PROVISTA POR LA

LAVAVAJILLAS ......................................................................... 20

CARACTERISTICAS DE LA LAVAVAJILLAS ......................... 21

CUlDADO DE LA LAVAVAJILLAS ........................................... 22

SOLUCION DE PROBLEMAS ................................................. 23

GARANTIA ................................................................................ 26

Su seguridad y la seguridad de los dem&s es muy importante.

Hemos incluido muchos mensajes importantes de seguridad en este manual y en su electrodomestico. Lea y obedezca siempre

todos los mensajes de seguridad.

Este es el simbolo de advertencia de seguridad.

Este simbolo le llama la atenci6n sobre peligros potenciales que pueden ocasionar la muerte o una lesi6n a

usted y a los demas.

Todos los mensajes de seguridad iran a continuaci6n del simbolo de advertencia de seguridad y de la palabra

"PELIGRO" o "ADVERTENCIA". Estas palabras significan:

Si no sigue las instrucciones de inmediato, usted puede

morir o sufrir una lesibn grave.

Si no sigue las instrucciones, usted puede morir o sufrir

una lesibn grave.

Todos los mensajes de seguridad le diran el peligro potencial, le diran c6mo reducir las posibilidades de sufrir una lesi6n y Io que

puede suceder si no se siguen las instrucciones.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

ADVERTENCIA: Cuando use la lavavajillas siga precauciones basicas, incluyendo las siguientes:

m Lea todas las instrucciones antes de usar la lavavajillas.

m Use la lavavajillas 0nicamente para las funciones que fue

dise_ada.

m Use 0nicamente detergentes o agentes de enjuague

recomendados para ser usados en las lavavajillas y

mant6ngalos fuera del alcance de los ni_os.

m AI introducir los articulos para lavar:

1) Coloque los arficulos puntiagudos de manera que no

da_en el sello de la puerta

2) Introduzca los cuchillos filosos con los mangos hacia

arriba para reducir el riesgo de cortaduras.

m No lave articulos de plastico que no Ileven la indicaci6n

"lavables en la lavavajillas" u otra similar. Lea las

recomendaciones del fabricante para los articulos de

plastico que no Ileven tal indicaci6n.

m No toque el elemento de calefacci6n durante o

inmediatamente despu6s de usar la lavavajillas.

[] No haga funcionar la lavavajillas a menos que todos los

paneles est_n colocados debidamente en su lugar.

[] No juegue con los controles.

[] No abuse, ni se siente ni se pare sobre la puerta, la tapa o

sobre las canastas de la lavavajillas.

[] Para reducir el riesgo de lesi6n, no permita que los ni_os

jueguen dentro ni sobre la lavavajillas.

[] Bajo ciertas condiciones, un sistema de agua caliente que

no ha sido usado pot dos semanas o mas puede producir

gas hidr6geno. EL GAS HIDROGENO ES EXPLOSlVO. Si

el sistema de agua caliente no ha sido usado por ese

periodo, abra todas las Ilaves de agua caliente y deje que

corra el agua pot varios minutos antes de usar la

lavavajillas. Esto permitirA que los gases acumulados

escapen. Debido a que el gas es inflamable, no fume ni

encienda ninguna llama abierta durante este tiempo.

[] Quite la puerta o la tapa del compartimiento de lavado

cuando remueva o deje de usar para siempre una vieja

lavavajillas.

GUARDE ESTAS INSTRUCCIONES

INSTRUCCIONES DE CONEXION A TIERRA

Para una lavavajillas con cable el6ctrico y conexi6n a

tierra:

La lavavajillas debe estar conectada a tierra. En caso de

funcionamiento defectuoso o averia, la conexi6n a tierra

reduce el riesgo de choque electrico al establecer una ruta

de menor resistencia para la corriente electrica. La

lavavajillas viene equipada con un cable electrico que tiene

un conductor para conexi6n a tierra y un enchufe con

conexi6n a tierra. El enchufe debe set conectado a un

contacto apropiado que este instalado y conectado a tierra

de acuerdo con todos los c6digos y ordenanzas locales.

ADVERTENCIA: La conexi6n inadecuada del

conductor de conexi6n a tierra puede resultar en riesgo

de choque electrico. Pregunte a un electricista

calificado o a un agente de servicio si no est,, seguro si

la lavavajillas est,, adecuadamente conectada a tierra.

No modifique el enchufe que viene con la lavavajillas. Si

no cabe en el contacto, pida que un electricista

calificado instale un contacto apropiado.

Para lavavajillas con conexi6n permanente:

Esta lavavajillas debe estar conectada a un sistema de

cableado de metal permanente, conectado a tierra, o se

debe tender un conducto para la conexi6n a tierra del

equipo con los conductores de circuito y conectado a la

terminal de tierra del equipo o al conductor de

suministro de la lavavajillas.

GUARDE ESTAS INSTRUCCIONES

Peligro de Vuelco

No use la lavavajillas antes de estar completamente instalada.

No se apoye en la puerta abierta.

No seguir estas instrucciones puede ocasionar heridas serias o cortaduras.

Advertencias de la Proposici6n 65 del estado de California:

ADVERTENCIA: Este producto contiene una o mas sustancias quimicas identificadas por el estado de California como

causantes de cancer.

ADVERTENCIA: Este producto contiene una o mas sustancias quimicas identificadas por el estado de California como

causantes de defectos cong6nitos o algOn otro tipo de daSos en la funci6n reproductora.

Prepare y cargue

la lavavajillas.

Seleccione un ciclo y una opcibn (los ciclos y las

opciones varian seg_n el modelo).

PowerBlast auto norma[ quick rinse

o000 o o

cycles delay

hitemp sanitize heated dry

0 0 0 0 0

] C3C3 ]

controlIock cancel s[ar[

hold 3 sec drain resume

Agregue el

detergente y el

agente de

enjuague.

A B

La pantalla totalmente iluminada se encendera para

lavado (A), secado (B), bloqueo (C), higienizado o

limpieza.

_. Ponga la 0

lavavajillas en

marcha.

start

resume

PASO 1

Prepare y cargue la lavavajillas

Us__'et- ' "'"

Modelo de carga para 10 puestos.

IMPORTANTE: Quite los restos de alimentos, huesos, palillos y

otros articulos duros de los platos. Quite las etiquetas de los

recipientes antes de lavarlos.

Modelo de carga para 8 puestos.

8 > j'_'

_t_/r..<:: =,.A

a< <_?,,¢\ _;)[%#"/,

Canasta superior

Modelo de carga para 12 puestos.

Canasta inferior

Canasta superior

Canasta inferior

Canasta superior

Canasta inferior

• AsegQrese de que nada impida que el (los)

brazo(s) rociador(es) gire(n) libremente. Es

importante que el rociado de agua alcance

todas las superficies sucias.

• AsegOrese de que cuando este cerrada la puerta de la

lavavajillas no haya articulos bloqueando el deposito de

detergente.

• Los articulos deberan cargarse con las superficies sucias

mirando hacia abajo y hacia adentro, hacia el rociador, como

se muestra. Esto mejorarA los resultados de limpieza y de

secado.

• Evite superponer los articulos como tazones o platos, que

pueden atrapar la comida.

• Coloque los plasticos, platos peque_os y vasos en la canasta

superior. Lave solo articulos de plastico marcados como

"lavable en la lavavajillas".

• Para evitar ruidos descomunales o estrepitosos durante el

funcionamiento: Coloque los platos de manera que no se

toquen entre si. AsegOrese de que los objetos livianos esten

firmes en las canastas.

• Cuando cargue la canastilla de los cubiertos,

coloque siempre los articulos filosos

apuntando hacia abajo. Mezcle otros

articulos con la punta hacia arriba y algunos

con la punta hacia abajo.

PASO2

Agregue detergente

NOTA: Si no va a hacer funcionar un ciclo de lavado de inmediato,

ponga un ciclo de enjuague. No use detergente.

• Use Onicamente A

detergentes para

lavavajillas

autom_ticas. Agregue B

detergente en polvo, .,,,,v..._,............C

liquido o en pastilla

justo antes de

comenzar un ciclo.

• El detergente para

lavavajillas autom_ticas

produce mejores A.Segure de la tapa

resultados cuando esta B.Secci6n de lavadeprincipal

C.Secci6n de prelavado

fresco. Guarde el

detergente bien cerrado

en un lugar fresco y seco.

• Para un rendimiento optimo, se recomienda detergente en

tableta.

Detergentes previamente medidos

Varios detergentes vienen ahora en formatos previamente medidos

(paquetes con gel, tabletas o paquetes con polvo). Estos formatos

son apropiados para todos los niveles de dureza y suciedad.

Coloque siempre los detergentes previamente medidos en el

compartimiento principal y cierre la tapa.

Esta comprobado que las pastillas y los paquetes de detergente

para lavavajillas son mas eficaces que los detergentes en polvo,

liquidos o en gel, para reducir las peliculas de residuos en la vajilla.

AI usar estas pastillas y paquetes, con el tiempo las peliculas

blancas comenzaran a reducirse o a eliminarse. Por otro lado, al

usar un agente de enjuague puede minimizar la acumulacion

repetida de peliculas blancas.

Polvos y geles

• La cantidad de detergente a usar depende de:

Cuanta suciedad permanece en los articulos - Las cargas con

suciedad profunda requieren mas detergente.

La dureza del agua - Si usa muy poco en agua dura, los platos

no quedarAn limpios. Si usa demasiado en agua blanda,

ocurrirA corrosion en las piezas de cristal.

Agua suave a medio dura (0-6 granos por galon de

EE.UU.)

[agua tipica tratada con ablandador de agua y cierto tipo

de agua urbana]

Agua medio dura a dura (7 a 12 granos por galon de

EE.UU.)

[agua de pozo y cierto tipo de agua urbana]

• SegOn la dureza del agua, Ilene la seccion de Main Wash

(Lavado principal) del deposito, como se muestra.

NOTA" Las cantidades de

Ilenado que se indican

corresponden a los

detergentes en polvo

estandares. Siga las

instrucciones del paquete

cuando use otro

detergente para

lavavajillas.

X HardWater 1 L

Soft Water

lavado principal prelavado

Agregue el agente de enjuague

Para obtener un buen secado, su lavavajillas ha sido dise_ada

para usar un agente de enjuague. Si no usa agente de

enjuague, los platos y el interior de la lavavajillas tendrAn

demasiada humedad. La opcion de secado con calor no

funcionarA tan bien sin usar el agente de enjuague.

Los agentes de enjuague evitan que el agua forme _ Full

gotitas que pueden secarse como manchas o rayas.

Asimismo mejoran el secado pues permiten que el

agua se escurra de los platos despu6s del enjuague

final.

Add

El agente de enjuague ayuda a reducir el exceso de

humedad sobre las canastas de los platos y el interior

de la lavavajillas.

Revise el indicador del agente de enjuague. Agregue el agente

de enjuague cuando el indicador baje hasta el nivel "Add"

(agregar).

Para agregar agente de

enjuague, gire la tapa del

deposito 1¼de vuelta en

sentido contrario alas

agujas del reloj y levantela.

Vierta el agente de

enjuague en la abertura

hasta que el indicador este

en "Full" (Lleno). Vuelva a

colocar la tapa del

deposito y girela hacia

"Lock" (Seguro).

AsegOrese de que la tapa

este asegurada por

completo.

USERINSEAIDFOR Full

BETTERDRYING

Lock

€:=__ Add

¼de giro para asegurar

NOTA: Para casi todos los

tipos de agua, la seleccion

de fabrica de 2 dara buenos

resultados. Si tiene agua

dura o nota que hay aros o

manchas, pruebe con un

ajuste mas alto. Gire el ajuste

de flecha que se encuentra

dentro del deposito usando

sus dedos o insertando un destornillador de hoja plana en el centro

de la flecha y haciendola girar.

PASO3 PASO4

Seleccione un ciclo (los ciclos varian seg6n el modelo)

Las lavavajillas eficientes funcionan por mas tiempo para ahorrar

agua y energia al igual que conducir un auto a menor velocidad

ahorra gas. Los tiempos de los ciclos pueden aumentar o disminuir

segQn las selecciones. Los tiempos estimados de los ciclos luego

de la calibracion se enumeran en la tabla "Descripciones de ciclos

y opciones" de la seccion siguiente. Cada vez que pulse el boton

Cycles (Ciclos), avanzarA al siguiente ciclo disponible

PowerBlast auto normal quick rinse

9 o o o o o

cycles de|ay

Seleccione las opciones (las opciones varian seg6n el

modelo)

Vea las tablas de "Descripcion de ciclos y opciones" en la seccion

siguiente.

Usted puede personalizar sus ciclos oprimiendo las opciones

deseadas y luego Start/Resume (Inicio/Reanudar).

hitemp sanitize heated dry

0 0 0 0 0

controllock cance| start

hold 3sec drain resume

Siga el progreso de su lavavajillas.

SegQn el modelo, el progreso se visualizarA con la pantalla

totalmente iluminada o con una luz indicadora en el panel frontal.

La pantalla totalmente iluminada se

encendera para lavado (A), secado (B), C

bloqueo (C), higienizado o limpieza.

Tambien mostrara el tiempo estimado

restante en horas y minutos.

A B

Cuando se selecciona Delay (Retraso),

la pantalla totalmente iluminada

mostrara una "h" para hora y la cantidad

de horas a retrasar.

Inicio o reanudaci6n de un ciclo

Deje correr agua caliente en el fregadero que este mas cerca

de su lavavajillas hasta que el agua salga caliente. Cierre la

Ilave del agua.

Empuje la puerta cerrandola con firmeza. La puerta 0

queda asegurada automaticamente. Seleccione el

ciclo y las opciones de lavado deseados y presione __

START/RESUME (Inicio/Reanudar) 0 BIEN s_ar_

presione START/RESUME (Inicio/Reanudar) para

repetir el mismo ciclo y opciones queen el ciclo anterior de

lavado.

Usted puede agregar un articulo en cualquier momento antes

de que comience el lavado principal. Abra lentamente la puerta

y agregue el articulo. Cierre la puerta con firmeza. Presione el

boton de START/RESUME (Inicio/Reanudar). El ciclo se

reanuda autom_ticamente en el momento en que fue

interrumpido.

Para modelos completamente incorporados (controles

en la parte superior de la consola)

• Seleccione el ciclo de lavado y opciones que desee.

• Presione una vez el boton de START/RESUME (Inicio/

Reanudar) y cierre la puerta. El ciclo comenzara despues de

una breve pausa. Debera cerrarse la puerta en menos de

4 segundos despues de presionar Start/Resume (Inicio/

Reanudar) o las luces destellaran y la lavavajillas no comenzara

afuncionar. Presione nuevamente el boton de START/RESUME

(Inicio/Reanudar) y cierre la puerta en menos de 4 segundos.

Usted puede agregar un articulo en cualquier momento antes de

que comience el lavado principal. Abra lentamente la puerta y

agregue el articulo. Presione el boton de START/RESUME (Inicio/

Reanudar) y cierre la puerta en menos de 4 segundos.

La luz indicadora sera azul para lavado,

rojo para secado o verde para ciclo completo.

PowerBJast auto normal quick rinse hitemp sanitize heated dry

o000 90 o o o o o

C3 C3[ZZ}{Z3C3

cycles delay contro_lock cancel start

hold 3 sec drain resume

A B

Esta informacion cubre varios modelos diferentes. Puede ser que su lavavajillas no cuente con todos los ciclos y opciones descritos.

ClCLOS TIEMPO DE AGUA

LAVADO AGREGA

ESTIMADO EN DA EN

PANTALLA GALON ES

(LITROS)

se disefi6 para limpiar la suciedad mAs rebelde: use este ciclo para ollas, sartenesl 3:28 9'0 (34,0)

cacerolas y vajilla comOn muy sucias que sean dificiles de lavar.

PowerBlast TM

auto

Ciclo de detecci6n de carga y suciedad. Este ciclo ha sido optimizado para Iograr

una mejor limpieza con una minima cantidad de agua y consumo de energia para

todos los niveles de suciedad.

2:03 4,5 (16,9)

se rec0m enda este ciclo c0nia 0pci6n de Heated D_ (secado ca!iente)1:51 3 8 (t4 5)

seleccionada Qnicamente, y sin otras opciones seleccionadas, para !avar y secar

normal totalmente una carga comp!eta de platos con suciedad normal. La etiqueta de

consurno de energia est4 basada en !a combinaci6n de este cic!o y opci6nl

quick

Para obtener resultados rapidos, este ciclo limpiarA lavajilla con suciedad ligera a

media usando mas agua y energia. Para mejorar elsecado, seleccione la opci6n de

secado con calor.

:59 5.5 (20,9)

Los tiempos de los ciclos pueden incrementarse segOn la temperatura del agua, condicion de suciedad intensa, tamafio de la carga de

vajilla y opciones seleccionadas.

*AI agregar opciones, aumentarA el tiempo del ciclo. Vea la seccion de informacion sobre las opciones.

delay

OPCIONES PUEDE LO QUE HACE TIEMPO AGUA

SELECCIO- AGREGA- AGREGAD

NARSE CON DO AL A EN

CICLO GALONES

(Litros)

Hace funcionar la lavavajillas a una hora posterior Disponible Retrasa el inicJo NA NA

o durante las horas que sean de menor consumo con cualquier de un ciclo hasta

de energia. Seleccione un ciclo y opciones de ciclo un maximo de

lavado. Presione Delay (Retraso) una vez para 24 horas.

cada hora adicio hal de retraso hasta un m4ximo

de 24 horas. Presione START/RESUME (Inicio/

Reanudar). Cierre la puerta con firmeza.

NOTA: En cualquier momento que se abra la

puerta (como puede ser para agregar un plato),

deber_ presio narse nuevamente el botdn de

START/RESUME (nicio/Reanudar) para reanudar

la cuenta regresiva del retraso.

OPCIONES PUEDE LO QUE HACE TIEMPO AGUA

SELECCIO- AGREGA- AGREGAD

NARSE CON DO AL A EN

CICLO GALONES

(Litros)

Eleva la temperatura del lavado principal para Auto

mejorar la limpieza en las cargas que contienen PowerBlastTM

hJtemp suciedad rebelde de los alimentos a causa del

O horneado. Normal

Aumenta la :04 a 1:16 0-1,2

temperatura del (0-4,5)

lavado principal

de 105 °F (41 °C)

a 129 °F (54 °C).

sanitize

,:ontrm_ocK

hold3sec

Higieniza los platos y piezas de cristal Auto

aumentando la temperatura del agua en el PowerBlastTM

enjuague final. Cumple con la norma NSF/ANSI Normal

184 para lavavajillas residenciales. Las lavavajillas

dom6sticas certificadas no han sido dise_adas

para los establecimientos con licencia para

alimentos. Esta opci6n agregarA calory tiempo al

c_clo.

AI final del ciclo, el indicador de higienizado (o la

palabra "sanitized" [higienizado] en algunos

modelos) se iluminar& Si su lavavajillas no

higieniz6 la carga adecuadamente, el indicador

destellarA al final del ciclo. Esto puede ocurrir si el

ciclo se interrumpi6, o si el agua no alcanza la

temperatura "equerida. La luz se apaga cuando

usted abre y cierra la puerta u oprime

CANCEL (Cancelar).

Aumenta la "04 a 1"15 0 - 3,0

temperatura del (0 - 11,2)

lavado principal

de 105 °F (41 °C)

a 145 °F (63 °C)

y el enjuague

final de 140 °F

(60 °C) a 156 °F

(69 °C)

Seca los platos con calor. Use la opcion con el Auto Usa el elemento :29 a :46 0

agente de enjuague para obtener mejores PowerBlastTM calefactor para

heateddry resultados de secado. Es menos probable que los acelerar los

carga en la canasta superior. Apague la opcion Quick secado.

para un secado al aire. (Rapido)

CONTROL PROPOSITO COMENTARIOS

: Para iniciar o reanudar un Si se abre la puerta durante un ciclo, o si se interrumpe el suministro de energia,

O cic!0 de !avado, deste!!ar_t e! indicador de START/RESUME (Inicio/Reanudar). El ciclo no se

__ reanudarA hasta que se cierre la puerta y se presione START/RESUME (Inicio!

Reanudar).

s_a[_ NOTA: Si e! bot6n de START/RESUME (Inici0/ReanUdar) estA Ubicado sobre la

puerta, empuje la misma firmemente para cerrar!a en menos de 4 segundos

despu6s de haber presionado START/RESUME. Si la puerta no se ha cerrado en

menos de 4 segundos, el LED de! bot6n de inici0 destellarA, se escucharA un tono

audible (en algunos mode!o s con contro! en !a parte suPerior) y e! cic!o no

comenzar&

Presione para cancelar un

Cierre la puerta con firmeza. La lavavajillas comienza un desagQe de 3 minutos (de

ser necesario). Deje que la lavavajillas complete el desagQe.

cancel

drain

Control Lock (Bloqueo de Para encender Lock (BloqUeo), mantenga presionado CONTROL LOCK (Bloqueo

O control) evita el uso de control)o SANITIZE (Higienizado)(segOn el modelo)por 3 segundosl La luz de

[ I accidental de !a lavavajillas Control Lock (Bloqueo de control) permanecera encendida durante un tiempo

L J entre los cic!os, o cambios corto, indicando que estA activada, y todos los botones se desactivarAn. Si usted

cancel

dro,, de los cic!os y opciones presiona cualquier bot6n mientras su lavavajillas est_ bloqueada, la luz destella 3

durante un cic!o, vecesl La puerta de la !avavaji!las puede aOn abrirse y cerrarse mientras los

contro!es estAn bloqueados.

€

Para apagar Lock (Bloqueo), mantenga pres_onado CONTROL LOCK (Bloqueo de

para bloquear los controles, el LED de Control Locked (Bloqueo de control) estara

encendido o apagado para indicar si e! B!oqueo de control estA activado o no,

CONTROL PROPOSITO COMENTARIOS

Para seguir el SegQn el modelo, el progreso se visualizarA con la pantalla totalmente iluminada o con

progreso del ciclo de una luz indicadora en el panel frontal.

la lavavajillas. La pantalla totalmente iluminada se encenderA para lavado (A), secado (B), higienizado

o limpieza. Tambi6n mostrarA el tiem po estimado restante del ciclo.

La luz indicadora serA azul para lavado, rojo para secado y verde para ciclo completo.

C6mo cancelar un ciclo

1. Abra la puerta ligeramente para detener el ciclo. Espere a que

la accion de rociado se detenga antes de abrir la puerta por

completo.

2. Presione una vez el boton CANCEL/DRAIN (Cancelar/

Desaguar). La luz Cancel/Drain se encender&

3. Cierre la puerta y la lavavajillas comienza un ciclo de desagQe

(si ha quedado agua en el fondo de la misma). Deje que la

lavavajillas complete el desagQe. La luz Cancel/Drain se apaga

al cabo de 3 minutos.

C6mo cambiar un ciclo despu_s de iniciar la lavavajillas

1. Puede interrumpir un ciclo y volver a iniciar la lavavajillas

desde el comienzo usando el siguiente procedimiento.

2. Abra la puerta ligeramente para detener el ciclo. Espere a que

la accion de rociado se detenga, luego abra la puerta por

completo.

3. Verifique que la tapa del deposito de detergente este aQn

cerrada. Si la tapa esta abierta, necesitara volver a Ilenar el

deposito de detergente antes de volver a iniciar el nuevo ciclo.

4. Presione CANCEL!DRAIN (Cancelar/Desaguar) dos veces

para volver a fijar el control.

5. Seleccione los nuevos ciclos y opciones.

6. Presione START/RESUME (Inicio/Reanudar).

C6mo agregar un plato despu_s de iniciar la lavavajillas

1. Verifique si se ha encendido el indicador de Add a Dish

(Agregar un plato). (Disponible en algunos modelos. De otro

modo, prosiga con el paso 2).

2. Abra la puerta ligeramente para detener el ciclo. Espere a que

la accion de rociado se detenga, luego abra la puerta por

completo.

3. Verifique si la tapa del deposito de detergente esta aQn

cerrada. Siesta abierta, el ciclo de lavado ya ha comenzado y

no se recomienda agregar un plato.

4. Si el detergente todavia no se uso (la tapa del deposito del

detergente esta cerrada), puede agregar un plato.

5. Presione START/RESUME (Inicio/Reanudar).

La page charge ...

Maytag MDB6949SDM0 Le manuel du propriétaire

Marque: Maytag

Modèle: MDB6949SDM0

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MDB6949SDM0 Owner's manual
español: Maytag MDB6949SDM0 El manual del propietario

Maytag MDB6949SDM0 Le manuel du propriétaire

Maytag MDB6949SDM0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents