Maytag MDE28PDCYW Guide d'installation

Table of Contents/Table des matières ................................................................................ 2

W11311968A

www.maytagcommerciallaundry.com

INSTALLATION INSTRUCTIONS

COMMERCIAL DRYER – GAS OR ELECTRIC

INSTRUCTIONS D’INSTALLATION

SÉCHEUSE COMMERCIALE – À GAZ OU ÉLECTRIQUE

2

TABLE OF CONTENTS

DRYER SAFETY .......................................................................... 2

INSTALLATION REQUIREMENTS ............................................. 5

Tools and Parts ......................................................................... 5

Location Requirements ............................................................. 6

Electrical Requirements ............................................................ 7

Gas Supply Requirements ..................................................... 10

Venting Requirements ........................................................... 11

Leveling .................................................................................. 13

INSTALLATION INSTRUCTIONS – GAS DRYER ................. 14

Make Gas Connection ............................................................. 14

Gas Supply Line ....................................................................... 14

Connect Vent ........................................................................... 15

Complete Installation .............................................................. 15

INSTALLATION INSTRUCTIONS – ELECTRIC DRYER ...... 16

Power Supply Cord (U.S.A. Only) ........................................... 16

Direct Wire Method (U.S.A. Only) ............................................ 20

Connect Vent ........................................................................... 23

Complete Installation .............................................................. 23

REVERSING THE DOOR SWING .......................................... 24

Remove the Door Assembly ................................................... 24

Reverse Hinge ......................................................................... 24

Reverse The Strike .................................................................. 25

Reinstall The Door .................................................................. 25

MAINTENANCE INSTRUCTIONS ......................................... 25

ELECTRONIC CONTROL SETUP ......................................... 26

WARRANTY ............................................................................ 30

■ It is recommended that the owner post, in a prominent location, instructions for the customer’s use in the event the customer smells

gas. This information should be obtained from your gas supplier.

■ Post the following warning in a prominent location.

DRYER SAFETY

TABLE DES MATIÈRES

SÉCURITÉ DE LA SÉCHEUSE .................................................. 31

EXIGENCES D’INSTALLATION ................................................. 34

Outils et pièces ........................................................................ 34

Exigences d’emplacement ...................................................... 35

Spécifications électriques ........................................................ 36

Spécifications de l’alimentation en gaz ................................... 39

Exigences concernant l’évacuation ......................................... 40

Nivellement............................................................................... 42

INSTRUCTIONS D’INSTALLATION – SÉCHEUSE À GAZ ...... 43

Raccordement au gaz ............................................................. 43

Canalisation d’alimentation en gaz ......................................... 43

Raccordement du conduit d’évacuation ................................. 44

Fin de l’installation ................................................................... 44

INSTRUCTIONS D’INSTALLATION – SÉCHEUSE

ÉLECTRIQUE .............................................................................. 45

Cordon d’alimentation (É.-U. seulement) ................................ 45

Méthode de raccordement direct (É.-U. seulement) .............. 49

Raccordement du conduit d’évacuation ................................. 52

Fin de l’installation ................................................................... 52

INVERSION DU SENS D’OUVERTURE DE LA PORTE .......... 53

Retrait de la porte .................................................................... 53

Inversion de la charnière.......................................................... 53

Inversion de la gâche ............................................................... 54

Réinstallation de la porte ......................................................... 54

INSTRUCTIONS D’ENTRETIEN ................................................ 55

RÉGLAGE DE LA CARTE DE CIRCUITS ÉLECTRONIQUE ... 55

GARANTIE ................................................................................... 60

3

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death or property

damage.

–

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

–

Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use any phone in your building.

•

Clear the room, building, or area of all occupants.

•

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

•

If you cannot reach your gas supplier, call the fire department.

4

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, Part 1, CSA C22.1.

Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch re.

To reduce the risk of re due to contaminated loads, the

nal part of a tumble dryer cycle occurs without heat

(cool down period). Avoid stopping a tumble dryer before

the end of the drying cycle unless all items are quickly

removed and spread out so that the heat is dissipated.

In the State of Massachusetts, the following installation instructions apply:

■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by

the State of Massachusetts.

■ Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed.

■ A flexible gas connector, when used, must not exceed 4 feet (121.9 cm).

5

Tools Needed:

8" or 10" 8" or 10" Flat-blade screwdriver Phillips screwdriver

Pipe wrench Adjustable wrench

that opens to 1"

TORX T20

®†

security 1" Hex-head 5⁄16" Socket wrench Pliers

screwdriver or bit socket wrench (that open to 1

9

/

16

")

Level Utility knife Pipe-joint compound Putty knife

resistant to Propane gas

Caulk gun and caulk Vent clamps

(for installing new exhaust vent)

INSTALLATION REQUIREMENTS

Parts supplied:

Remove parts bag from dryer drum. Check that all parts were

included.

■ Foot boot (4)

■ Dryer foot (4)

■ PD models: Cam for service door lock

PR models: Card reader bezel, card reader wire harness,

hardware

Optional parts not included:

■ 279810 Long dryer foot

■ LP Kit W10402145

■ 208 V electric element:

U.S. – W10206352A, Canada – W10206351A

†® TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

Tools & Parts

6

Location Requirements

IMPORTANT: Do not install or store the dryer where it will be

exposed to the weather. Proper installation is your responsibility.

You will need:

■ A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the dryer.

See “Electrical Requirements.”

■ A level oor with a maximum slope of 1" (25 mm) under entire

dryer. Installing the dryer on soft oor surfaces, such as

carpets or surfaces with foam backing, is not recommended.

If installing a gas dryer:

IMPORTANT: Observe all governing codes and ordinances.

■ Check code requirements: Some codes limit or do not permit

installation of clothes dryers in garages, closets, or sleeping

quarters. Contact your local building inspector.

■ Make sure that lower edges of the cabinet, plus the back and

bottom sides of the dryer, are free of obstructions to permit

adequate clearance of air openings for combustion air. See

“Recessed Area and Closet Installation Instructions” below

for minimum spacing requirements.

NOTE: The dryer must not be installed in an area where it will

be exposed to water and/or weather.

Recessed Area and Closet Installation Instructions

This dryer may be installed in a recessed area or closet.

For recessed area and closet installations, minimum clearances

can be found on the warning label on the rear of the dryer.

The installation spacing is in inches and is the minimum

allowable. Additional spacing should be considered for ease

of installation, servicing, and compliance with local codes

and ordinances.

If closet door is installed, the minimum unobstructed air opening

in the top and bottom is required. Louvered doors with equivalent

air openings are acceptable.

The dryer must be exhausted outdoors.

No other fuel-burning appliance may be installed in the same

closet as the dryer.

Closet

door

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not install in a garage.

Failure to do so can result in death, explosion, or fire.

Recessed front view Closet side view

Minimum Installation Clearances

* Additional clearances for wall, door, and oor moldings may be required

or if external exhaust elbow is used.

closet

door

Front

View

3" (76 mm)

24 in

2

(155 cm

2

)*

* Opening is the minimum

for a closet door.

Louvered doors with

equivalent air openings

are acceptable.

14"

(356 mm)

max.

1" (25 mm)

0" (0 mm)

15"

(381 mm)*

28

3

⁄4"

(733 mm)

6

1

⁄4"

(159 mm)

ELECTRIC

GAS

EXHAUST

LEFT OR

RIGHT SIDE

EXHAUST

4

1

⁄4"

(108 mm)

13"

(330 mm)

1

⁄4"

(32 mm)

BACK

VIEW

4

1

⁄4" (108 mm)

6

3

⁄4"

(152 mm)

4" (102 mm)

dia.

3/4" (21 mm)

SIDE VIEW

BOTTOM

EXHAUST

35"

(889 mm)

27

1

⁄4" (695 mm)

29" (736 mm)

14

1

⁄8"

(359 mm)

7

1

⁄4"

(184 mm)

10

1

⁄4"

(260 mm)

27" (686 mm)

0"

(0 mm)

0" (0 mm)

7

⁄8"

(200 mm)

Product Dimensions 27" (68.6 cm) Dryer

48 in

2

.

(310 cm

2

)*

7

Electrical Requirements – Gas Dryer

IMPORTANT: The dryer must be electrically grounded in

accordance with local codes and ordinances or, in the absence

of local codes, with the National Electrical Code, ANSI/NFPA 70,

latest edition, or Canadian Electrical Code, CSA C22.1. If codes

permit and a separate ground wire is used, it is recommended

that a qualied electrical installer determine that the ground path

is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

■ Do not ground to a gas pipe.

■ Do not have a fuse in the neutral or ground circuit.

■ A 120 V, 60 Hz, AC only, 15 or 20 A, fused electrical circuit

is required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this dryer be provided.

■ This dryer is equipped with a power supply cord having a

3-prong grounding plug.

■ To minimize the possibility of shock, the cord must be

plugged into a mating, 3 prong, grounding-type outlet,

grounded in accordance with local codes and ordinances.

If a mating outlet is not available, it is the personal

responsibility and obligation of the customer to have the

properly grounded outlet installed by a qualied electrician.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that the

ground path is adequate.

■ Check with a qualied electrician if you are not sure the dryer

is properly grounded.

Gas Dryer Grounding

8

Electrical Requirements –

Electric Dryer (U.S.A. Only)

It is your responsibility:

■ To contact a qualied electrical installer.

■ To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

■ The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

■ A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

■ To supply the required 3 or 4 wire, single phase, 120/240 V,

60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 V

electrical supply, if specied on the serial/rating plate) on a

separate 30 A circuit, fused on both sides of the line. A time

delay fuse or circuit breaker is recommended. Connect to an

individual branch circuit. Do not have a fuse in the neutral or

grounding circuit.

■ Do not use an extension cord.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that

the ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

■ This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The neutral ground conductor is

permanently connected to the neutral conductor (white wire)

within the dryer. If the dryer is installed with a 4-wire electrical

supply connection, the neutral ground conductor must be

removed from the external ground connector (green screw),

and secured under the neutral terminal (center or white wire)

of the terminal block. When the neutral ground conductor is

secured under the neutral terminal (center or white wire) of the

terminal block, the dryer cabinet is isolated from the neutral

conductor.

■ If local codes do not permit the connection of a neutral

ground wire to the neutral wire, see “Optional 3-wire

connection” section.

■ A 4-wire power supply connection must be used when the

appliance is installed in a location where grounding through

the neutral conductor is prohibited. Grounding through the

neutral is prohibited for (1) new branch-circuit installations

(2) areas where local codes prohibit grounding through the

neutral conductor.

Electric Dryer Grounding

9

Electric Dryer Power Supply Cord

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

■ A UL listed 30 A power supply cord, rated 120/240 V

minimum. The cord should be type SRD or SRDT and be at

least 4 ft. (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or “U” shaped spade terminals

with upturned ends.

■ A UL listed strain relief.

If your outlet looks like this:

Then choose a 4-wire power supply cord with ring

or spade terminals and UL listed strain relief. The

4-wire power supply cord, at least 4 ft. (1.22 m)

long, must have four 10-gauge copper wires and

match a 4-wire receptacle of NEMA Type 14-30R.

The ground wire (ground conductor) may be either

green or bare. The neutral conductor must be

identied by a white cover.

Then choose a 3-wire power supply cord with ring

or spade terminals and UL listed strain relief. The

3-wire power supply cord, at least 4 ft. (1.22 m)

long, must have three 10-gauge copper wires and

match a 3-wire receptacle of NEMA Type 10-30R.

If your outlet looks like this:

Fire Hazard

Use 10 gauge copper wire.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal.

Ground wire (green or bare wire) must be connected

to green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electrical shock.

Direct Wire

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

■ Flexible armored cable or nonmetallic sheathed copper

cable (with ground wire), covered with exible metallic

conduit. All current-carrying wires must be insulated.

■ 10-gauge solid copper wire (do not use aluminum).

■ At least 5 ft. (1.52 m) long.

4-Wire

Receptacle

(14-30R)

3-Wire

Receptacle

(10-30R)

10

Gas Supply Requirements

IMPORTANT: Observe all governing codes and ordinances.

This installation must conform with all local codes and

ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1/NFPA 54 or CAN/CSA B149.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

The design of this dryer has been certied by CSA International

for use at altitudes up to 10,000 feet (3048 m) above sea level at

the B.T.U. rating indicated on the model/serial plate. Burner input

adjustments are not required when the dryer is operated up to

this elevation.

When installed above 10,000 feet (3048 m), a four percent (4%)

reduction of the burner B.T.U. rating shown on the model/serial

plate is required for each 1,000 foot (305 m) increase in elevation.

For assistance when converting to other gas types and/or

installing above 10,000 feet (3048 m) elevation, contact your

local service company.

Type of Gas

This dryer is equipped for use with natural gas. It is design-

certied by CSA International for propane and butane gases with

appropriate conversion. No attempt shall be made to convert

the dryer from the gas specied on the serial/rating plate for use

with a different gas without consulting the serving gas supplier.

Conversion must be done by a qualied service technician.

Gas conversion kit part number is W10402145. This part number

is also available on a label on the gas valve burner base.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to propane, have a qualified person make

sure gas pressure does not exceed 13" (33 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Electrical Requirements – Canada only

It is your responsibility:

■ To contact a qualied electrical installer.

■ To be sure that the electrical connection is adequate

and in conformance with the Canadian Electrical Code,

C22.1 – latest edition and all local codes. A copy of the

above codes standard may be obtained from: Canadian

Standards Association,178 Rexdale Blvd., Toronto, ON

M9W 1R3 CANADA.

■ To supply the required 4 wire, single phase, 120/240 V,

60 Hz., AC only electrical supply on a separate 30 A circuit,

fused on both sides of the line. A time-delay fuse or circuit

breaker is recommended. Connect to an

individual branch circuit.

■ This dryer is equipped with a CSA International

Certied Power Cord intended to be plugged

into a standard 14-30R wall receptacle. The

cord is 5 ft (1.52 m) in length. Be sure wall

receptacle is within reach of dryer’s nal

location.

■ Do not use an extension cord.

If you are using a replacement power supply cord, it is

recommended that you use Power Supply Cord Replacement

Part Number 9831317. For further information, please

reference the service numbers located in the “Assistance or

Service” section.

4-Wire

Receptacle

(14-30R)

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualied electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not t the outlet, have a proper outlet

installed by a qualied electrician.

11

Allow as much room as possible when using elbows or making

turns. Bend vent gradually to avoid kinking.

Vent outlet is located at the back of the dryer, at bottom center.

The vent can be routed up, down, left, right, behind the dryer,

or straight out the back of the dryer. See “Product Dimensions”

in the “Location Requirements” section.

Make-up air:

Although each single-load dryer should have an unobstructed

outdoor air opening of 24 in

2

(154 cm

2

) (based on 1 square

inch [6.5 cm

2

] per 1,000 Btu [252 kcal]), common make-up air

openings are also acceptable. Set up common openings so that

the make-up air is distributed equally to all of the dryers. Keep

in mind that the coverage area must be increased by 33% to

account for use of registers or louvers over the openings. Also,

make-up air openings should not be installed near the location

of exhaust vents exiting the building.

Vent System Length

Maximum length of vent system depends upon the type of

vent used, number of elbows, and type of exhaust hood.

The maximum length for rigid vent is shown in the chart.

Maximum Vent Length

4" (102 mm) Diameter Exhaust Hoods

Vent System Chart (Rigid Metal Vent)

No. of 90° Box Hood and

Turns Louvered Style Angled Hood Style

0 130 ft. (39.6 m) 129 ft. (39.3 m)

1 125 ft. (38.1 m) 119 ft. (36.3 m)

2 115 ft. (35.1 m) 109 ft. (33.2 m)

3 106 ft. (32.3 m) 100 ft. (30.5 m)

4 98 ft. (29.9 m) 92 ft. (28.0 m)

For vent systems not covered by the vent specication chart,

see your parts distributor.

Provision must be made for enough air for combustion and

ventilation. (Check governing codes and ordinances.) See

“Recessed Area and Closet Installation Instructions” in the

“Location Requirements” sections.

A 4" (102 mm) outlet hood is preferred. However, a 2

1

⁄2" (64 mm)

outlet exhaust hood may be used. A 2

1

/2" (64 mm) outlet creates

greater back pressure than other hood types. For permanent

installation, a stationary vent system is required.

Connect Vent

1. If connecting to existing vent, make sure the vent is clean.

2. Using a 4" (102 mm) clamp, connect vent to exhaust outlet

in dryer.

NOTE: Do not remove vent collar.

Venting Requirements

WARNING: To reduce the risk of re, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

■ The dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, attic, crawlspace, or a concealed space

of a building. Only rigid or exible vent shall be used for

exhausting.

■ Only a 4" (102 mm) heavy, metal exhaust vent and clamps

may be used.

■ Do not use an exhaust hood with a magnetic latch.

■ Use clamps to seal all joints. Do not use screws or other

fastening devices that extend into the interior of the duct

and catch lint. Do not use duct tape.

■ Do not use plastic or metal foil vent.

Rigid metal vent:

■ Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent (acceptable only if accessible to clean):

■ Must be fully extended and supported in nal dryer location.

■ Remove excess to avoid sagging and kinking that may result

in reduced airow and poor performance.

■ Do not install in enclosed walls, ceilings, or oors.

■ The total length should not exceed 7

3

/4 ft. (2.4 m).

An exhaust hood should cap the vent to prevent rodents and

insects from entering the home or business.

Exhaust hood must be at least 12" (305 mm) from the ground

or any object that may be in the path of the exhaust (such as

owers, rocks, or bushes).

If using an existing vent system, clean lint from the entire length

of the system and make sure exhaust hood is not plugged with

lint. Replace any plastic or metal foil vent with rigid metal or

exible metal vent.

Plan installation to use the fewest number of elbows and turns.

Box Louvered

2

1

⁄2" (63.5 mm) Angled

Good

Better

Vent Collar

12

For vent systems not covered by the vent specication chart,

see your parts distributor.

If dryer is installed in a conned area, such as a bedroom,

bathroom, or closet, provision must be made for enough air

for combustion and ventilation. (Check governing codes and

ordinances.) See “Recessed Area and Closet Installation

Instructions” in the “Location Requirements” section.

A 4" (102 mm) outlet hood is preferred. However, a 2

1

⁄2" (64 mm)

outlet exhaust hood may be used. A 2

1

⁄2" (64 mm) outlet creates

greater back pressure than other hood types. For permanent

installation, a stationary vent system is required.

If An Exhaust Hood Cannot Be Used

The outside end of the main vent should have a sweep elbow

directed downward.

If the main vent travels

vertically through the roof,

rather than through the

wall, install a 180° sweep

elbow on the end of the

vent at least 2 ft. (610 mm)

above the highest part of

the building. The opening in

the wall or roof shall have a

diameter 1/2" (13 mm) larger

than the vent diameter. The

vent should be centered in

the opening.

Do not install screening or

cap over the end of the vent.

12" min.

(305 mm)*

24" min.

(610 mm)

* Minimum

clearance above

any accumulation

of snow, ice,

or debris such

as leaves

Multiple Dryer Venting

■ A main vent can be used for venting a group of dryers. The

main vent should be sized to remove 200 CFM of air per

dryer. Large-capacity lint screens of proper design may be

used in the main vent if checked and cleaned frequently. The

room where the dryers are located should have make-up air

equal to or greater than the CFM of all the dryers in the room.

■ A back-draft damper kit is needed and is available from a

commercial laundry distributor; it should be installed in the

vent of each dryer to prevent exhausted air from returning into

the dryers and to keep the exhaust in balance within the main

vent. Unobstructed return air openings are required.

Each vent should enter the main vent at an angle pointing in the

direction of the airow. Vents entering from the opposite side

should be staggered to reduce the exhausted air from interfering

with the other vents.

The maximum angle of each vent entering the main vent should

be no more than 30°.

Keep air openings free of dry cleaning uid fumes. Fumes create

acids which, when drawn through the dryer heating units, can

damage dryers and items being dried.

A clean-out cover should be located on the main vent for periodic

cleaning of the vent system.

30˚ max.

Air ow

Air flow

3. Tighten hose clamp with Phillips screwdriver.

4. Make sure the vent is secured to exhaust hood with

a 4" (102 mm) clamp.

5. Move dryer into nal position. Do not crush or kink vent.

Make sure dryer is level.

NOTE: Testing for proper ventilation should be done with a

Manometer. Minimum: 0.01" (0.2 mm). Maximum: 0.6" (16 mm).

13

Leveling

Leveling your dryer properly reduces excess noise and vibration.

1. Remove cardboard from beneath dryer. Place a level on top

edges of dryer, checking each side and front. If not level,

tip dryer and adjust legs up or down as shown in Step 3,

repeating as necessary.

2. Grip dryer from top and rock back and forth, making sure all

four legs are rmly on oor. Repeat, rocking dryer from side

to side. If dryer rocks, go to Step 3 and adjust leveling legs.

3. If dryer is not level, use a 1" or 25 mm open-end or adjustable

wrench to turn the leveling leg counterclockwise to lower the

dryer or clockwise to raise the dryer. Recheck levelness of

dryer and that all four legs are rmly in contact with the oor.

Repeat as needed.

HELPFUL TIP: You may want to prop up front of dryer about

4" (102 mm) with a wood block or similar object that will

support weight of dryer.

(appearance may vary)

Not Level LEVEL Not Level

(appearance may vary)

14

Gas Supply Pressure Testing

A 1/8" (3 mm) NPT minimum plugged tapping, accessible for

gauge testing, must be installed immediately downstream of the

installed shut-off valve to the dryer (as shown above). The dryer

must be disconnected from the gas supply piping system during

any pressure testing of the system at test pressures in excess of

1/2" psig (352 kg/m

2

). The expected pressures for the gas supply

are listed in inches of water in the table below:

Natural Gas Propane Gas

Minimum

5.2" (132.1 mm) 8.0" (203.2 mm)

Maximum

10.5" (266.7 mm) 13.0" (330.2 mm)

Alternate method

■ The gas supply may also be connected using 3/8" approved

copper or aluminum tubing. If the total length of the supply

line is more than 20 ft. (6.1 m), larger tubing will be required.

If using natural gas, do not use copper tubing. Pipe joint

compounds that resist the action of Propane gas must be

used.

Flexible metal appliance connector:

■ It is recommended that a new exible stainless steel gas line,

design-certied by CSA International, be used for connecting

the dryer to the gas supply line. (The gas pipe, which extends

through the lower rear of the dryer, is provided with 3/8"male

pipe thread.)

■ Do not kink or damage the exible stainless steel gas line

when moving the dryer.

Rigid pipe connection:

The rigid pipe connection requires a combination of pipe ttings

to obtain an in-line connection to the dryer.

Make Gas Connection

1. Remove red cap from gas pipe.

2. Connect gas supply to dryer. Use pipe-joint compound

resistant to the action of propane for gas connections.

If exible metal tubing is used, be certain there are no kinks.

If necessary for service, open the toe panel by removing the

2

1

⁄4" hex-head screws from the bottom of the panel. Then lift

up on the panel while pulling the bottom of the panel away

from the dryer.

3. Open the shutoff valve in the gas supply line.

4. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show

a leak. Correct any leak found.

Gas Supply Line

Recommended method

■ Provide a gas supply line of 1/2" rigid (IPS) pipe to the dryer

location. Pipe joint compounds that resist the action of

Propane gas must be used. Do not use TEFLON

®†

tape. With

Propane gas, piping or tubing size can be 1/2" minimum.

Usually, Propane gas suppliers determine the size and

materials used in the system.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to propane, have a qualified person make

sure gas pressure does not exceed 13" (33 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

INSTALLATION INSTRUCTIONS – GAS DRYER

†®TEFLON is a registered trademark of Chemours.

15

■ Must include a shutoff valve:

The supply line must be equipped with a manual shutoff

valve installed within 6 ft. (1.8 m) of dryer in accordance

with National Fuel Gas Code, ANSI Z223.1. In Canada,

an individual manual shutoff valve must be installed in

accordance with the B149 installation codes CAN/CGA

B149.1 and CAN/CGA B149.2. This valve should be located

in the same room as the dryer. It should be in a location that

allows ease of opening and closing. Do not block access to

shutoff valve. The valve is for turning on or shutting off gas

to the dryer.

DC

A B

A. Gas supply line

B. Shutoff valve in “open” position

C. To dryer

D. NPT 1/8" min. plugged tapping

■ Installed in a conned area:

If the dryer is installed in a conned area such as a

bathroom or closet, provision must be made for enough

air for combustion and ventilation. Check governing codes

and ordinances or refer to the “Recessed Area and Closet

Installation Instructions” in the “Location Requirements”

section.

Connect Vent

1. Using a 4" (102 mm) clamp, connect vent to exhaust outlet

on the dryer. If connecting to existing vent, make sure the

vent is clean. The dryer vent must t over the dryer exhaust

outlet and inside the exhaust hood. Make sure the vent is

secured to exhaust hood with a 4" (102 mm) clamp.

2. Using two or more people, move dryer to desired installation

location. Do not crush or kink vent, and remove any excess

exible vent to improve airow. Make sure dryer is level.

3. Check to be sure there are no kinks in the exible gas line.

Complete Installation

1. With dryer in nal position, place level on top of the dryer, rst

side to side; then front to back. If the dryer is not level, adjust

the legs of the dryer up or down until the dryer is level.

2. Check the electrical requirements. Be sure that you have the

correct electrical supply and the recommended grounding

method. See “Electrical Requirements.”

3. Check that all parts are now installed. If there is an extra part,

go back through the steps.

4. Check that you have all of your tools.

5. Dispose of/recycle all packaging materials.

Electrical Shock Hazard

Plug into a grounded 3 or 4 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

6. Plug into a grounded outlet, or connect power.

7. Check dryer operation:

Insert coins. Select a cycle. Using the WHITES & COLORS

cycle, let the dryer run for at least ve minutes. Dryer will stop

when time is used up.

Note: Dryer door must be closed for dryer to operate.

When door is open, dryer stops, but timer continues to run.

To restart dryer, close door and reselect a cycle.

8. If the burner does not ignite and there is no heat inside the

dryer, shut off dryer for ve minutes. Check that all gas supply

valves are in the “ON” position and that the electrical cord is

plugged in. Repeat ve-minute test.

9. If drying time is too long, make sure that the lint screen is

clean and that there are no obstructions to airow in the dryer

vent system.

16

1. Disconnect power.

2. Remove the hold-down screw and terminal block cover.

A

B

E

D

C

3. Install strain relief.

INSTALLATION INSTRUCTIONS – ELECTRIC DRYER

Power Supply Cord (U.S.A. Only)

A. Terminal block cover

B. External ground

conductor screw

C. Center terminal block screw

D. Hold-down screw

E. Neutral ground wire

17

A. Strain relief tab

pointing up

B. Hole below terminal

block opening

C. Clamp section

D. Strain relief tab

pointing down

C

B

A

D

Tighten strain relief screws enough to hold

the two clamp sections together.

Power supply cord strain relief:

■ Remove the screws from a 3/4" (19 mm)

UL listed strain relief (UL marking on

strain relief). Put the tabs of the two clamp

sections into the hole below the terminal

block opening so that one tab is pointing

up and the other is pointing down, and

hold in place.

■ Put power supply cord through the strain

relief. Be sure that the wire insulation on

the power supply cord is inside the strain

relief. The strain relief should have a tight

t with the dryer cabinet and be in a

horizontal position. Do not further tighten

strain relief screws at this point.

Electrical Connection Options

If your location has: And you will be Go to Section

connecting to:

4-wire receptacle A UL listed, 120/240 V 4-wire connection:

(NEMA Type 14-30R) minimum, 30 A, Power supply cord

dryer power supply cord*

3-wire receptacle A UL listed, 120/240 V 3-wire connection:

(NEMA type 10-30R) minimum, 30 A, Power supply cord

dryer power supply cord*

4-wire direct A fused disconnect or 4-wire connection:

circuit breaker box* Direct Wire

3-wire direct A fused disconnect or 3-wire connection:

circuit breaker box* Direct Wire

*If local codes do not permit the connection of a cabinet-ground conductor to the neutral wire, go to “Optional 3-wire

connection” section.

1"

(25 mm)

5"

(127 mm)

3

1

⁄2

”

(89 mm)

18

C

B

A

D

1. Remove center terminal block screw (B).

2. Remove neutral ground wire (C) from

external ground conductor screw (A).

Connect neutral ground wire and

the neutral wire (white or center wire)

of power supply cord under center

terminal block screw (B). Tighten screw.

IMPORTANT: A 4-wire connection is

required for mobile homes and where local

codes do not permit the use of 3-wire

connections.

Power supply cord,

4-wire connection:

A. 4-wire receptacle (NEMA type 14-30R)

B. 4-prong plug

C. Ground prong

D. Neutral prong

E. Spade terminals with upturned ends

F.

3/4"

(19 mm) UL listed strain relief

G. Ring terminals

A. External ground conductor screw - Dotted line shows position

of NEUTRAL ground wire before being moved to center

terminal block screw.

B. Center terminal block screw

C. Neutral ground wire

D. Neutral wire (white or center wire)

E.

3/4"

(19 mm) UL listed strain relief

A. External ground conductor screw

B. Ground wire (green or bare) of power supply cord

C.

3/4"

(19 mm) UL listed strain relief

D. Center terminal block screw

E. Neutral ground wire

F. Neutral wire (white or center wire)

3. Connect ground wire (B) (green or bare)

of power supply cord to external ground

conductor screw (A). Tighten screw.

5. Tighten strain relief screws.

6. Insert tab of terminal block cover into

slot of dryer rear panel. Secure cover

with holddown screw.

7. You have completed your electrical

connection. Now go to “Venting

Requirements.”

4. Connect the other wires to outer terminal

block screws. Tighten screws.

E

F

G

C

B

A

D

E

F

C

B

A

D

E

19

A. External ground conductor screw

B. Neutral ground wire

C. Center terminal block screw

D. Neutral wire (white or center wire)

E. 3/4" (19 mm) UL listed strain relief

A. 3-wire receptacle (NEMA type 10-30R)

B. 3-wire plug

C. Neutral prong

D. Spade terminals with upturned ends

E. 3/4" (19 mm) UL listed strain relief

F. Ring terminals

G. Neutral (white or center wire)

Power supply cord,

3-wire connection:

Use where local codes permit connecting

cabinet-ground conductor to neutral wire.

1. Loosen or remove center terminal

block screw (C).

2. Connect neutral wire (white or center

wire) of power supply cord (D) to the

center terminal screw (C) of the terminal

block. Tighten screw.

3. Connect the other wires to outer terminal

block screws. Tighten screws.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into

slot of dryer rear panel. Secure cover

with holddown screw.

6. You have completed your electrical

connection. Now go to “Venting

Requirements.”

C

B

A

D

E

F

G

C

B

A

D

E

20

Fire Hazard

Use 10 gauge copper wire.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal.

Ground wire (green or bare wire) must be connected

to green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electrical shock.

A. Removable conduit connector

B. Hole below terminal block opening

C. Strain relief threads

B

C

A

Direct wire strain relief:

■ Unscrew the removable conduit

connector (A) and any screws from a

3/4" (19 mm) UL listed strain relief

(UL marking on strain relief). Put the

threaded section of the strain relief

through the hole (B) below the terminal

block opening. Reaching inside the

terminal block opening, screw the

removable conduit connector onto the

strain relief threads (C).

■ Put direct wire cable through the strain

relief. The strain relief should have a

tight t with the dryer cabinet and be in

a horizontal position. Tighten strain relief

screw against the direct wire cable.

4. Now complete installation following

instructions for your type of electrical

connection:

4-wire (recommended)

3-wire (if 4-wire is not available)

Direct wire cable must match power supply (4-wire or 3-wire)

and be:

■ Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), protected with exible metallic conduit.

All current-carrying wires must be insulated.

■ 10-gauge solid copper wire (do not use aluminum).

■ At least 5 ft. (1.52 m) long.

1. Disconnect power.

2. Remove hold-down screw and terminal block cover.

A

B

E

D

C

A. Terminal block cover

B. External ground

conductor screw

C. Center terminal block screw

D. Hold-down screw

E. Neutral ground wire

3. Install 3/4" conduit connector into the hole below the terminal

block opening. Connect exible metallic conduit and tighten

connector screw. Install direct wire cable through the exible

metallic conduit.

4. Complete installation following instructions for your type

of electrical connection:

• Four-wire (recommended method)

• Three-wire (if four-wire is not available)

Direct Wire Method (U.S.A. Only)

La page charge ...

Maytag MDE28PDCYW Guide d'installation

Maytag MDE28PDCYW Guide d'installation

dans d''autres langues