ProCom Heating 200060 Mode d'emploi

PROPANE CONSTRUCTION FORCED AIR HEATER

OWNER’S MANUAL

PCFA40 - 40,000 BTU/HR HEATER

PCFA60V - 60,000 BTU/HR HEATER

IMPORTANT: Read and understand this manual before

assembling, starting or servicing heater. Improper use

of heater can cause serious injury. Keep this manual for

future reference.

GENERAL HAZARD WARNING:

Failure to comply with the precautions and instructions

provided with this heater, can result in death, serious

bodily injury and property loss or damage from hazards

of re, explosion, burn, asphyxiation, carbon monoxide

poisoning and/or electrical shock.

Only persons who can understand and follow the in-

structions should use or service this heater.

If you need assistance or heater information such as an

instructions manual, labels, etc. contact the manufacturer.

Questions, problems, missing parts? Before returning to your retailer, call

our customer service department at 1-866-573-0674, 7:30 am - 4:15 pm CST,

Monday through Friday or email customerservice@usaprocom.com

www.usaprocom.com

160448-01C2

SPECIFICATIONS

Model PCFA40 PCFA60V

Output Rating 40,000 BTU/Hr 60,000 BTU/Hr

Fuel Consumption/Hour 0.44 gal (1.65 liter),

1.86 lb (0.84 kg)

0.66 gal (2.48 liter),

2.78 lb (1.26 kg)

Manifold Pressure 9.7 PSI 19.8 PSI

Ignition Manual Piezo Electric Spark

Fuel Propane Vapor

Supply Pressure To Regulator Minimum* 20 psi Minimum* 25 psi

Maximum Tank Pressure or 200 psi

Regulator Outlet Pressure 10 PSI 20 PSI

Motor 2000 RPM 2900 RPM

Electric Input 120 Volt/60 Hertz/1 Phase

Amperage 0.6

Temperature Range for Heater Operation 0° F to 85° F** (-17° C to 29.4° C**)

* For purposes of input adjustment

** When running heater in temperatures above 85° F (29.44° C), high internal temperatures may cause

thermal limit device to shut down heater.

TABLE OF CONTENTS

Specications ............................................ 2

Safety ........................................................ 3

Unpacking.................................................. 4

Product Identication ................................. 4

Theory of Operation................................... 5

Propane Supply ......................................... 5

Installation ................................................. 5

Ventilation .................................................. 7

Operation ................................................... 7

Storage ...................................................... 8

Maintenance .............................................. 8

Service Procedures ................................... 9

Troubleshooting ........................................11

Parts ........................................................ 12

Wiring Diagram ........................................ 16

Replacement Parts .................................. 16

Accessories ............................................. 17

Technical Services ................................... 17

Warranty .................................................. 18

www.usaprocom.com

3160448-01C

SAFETY

ziness and/or nausea. If you have these signs,

the heater may not be working properly. Get

fresh air at once! Check for proper ventilation

and have heater serviced.

Propane Gas: Propane gas is odorless. An

odor-making agent is added to propane gas.

The odor helps you detect a propane gas

leak. However, the odor added to propane

gas can fade. Propane gas may be present

even though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this heater.

1. Install and use heater with care. Follow

all local ordinances and codes. In the ab-

sence of local ordinances and codes, refer

to the Standard for Storage and Handling

of Liqueed Petroleum Gas, ANSI/NFPA

58 and the Natural and Propane Gas

Installation Code, CAN/CGA B149.1. This

instructs on the safe storage and handling

of propane gases.

2. Use only the electrical voltage and fre-

quency specied on model plate. The

electrical connections and grounding of

the heater shall follow the National Electric

Code, ANSI/NFPA 70 or the Canadian

Electrical Code, Part 1.

3. Electrical grounding instructions - This

appliance is equipped with a three-prong

(grounding) plug for your protection against

shock hazard and should be plugged di-

rectly into a properly grounded three-prong

receptacle or extension cord.

4. This product has been approved for use

in the Commonwealth of Massachusetts.

5. Use only a three-prong, grounded exten-

sion cord.

6. Use only the hose and factory preset

regulator provided with the heater.

7. Use only propane gas set up for vapor

withdrawal.

8. Provide adequate ventilation. Before

using heater, provide at least a 1.5 ft

2

(1400 cm

2

) opening of fresh, outside air.

9. For either indoor or outdoor use. Adequate

ventilation must be provided. Do not use

heater outdoors.

10. Do not use heater in occupied dwellings

or in living or sleeping quarters.

WARNING: This product

contains and/or generates

chemicals known to the State

of California to cause cancer or

birth defects or other reproduc-

tive harm.

WARNING: Fire, burn, in-

halation and explosion hazard.

Keep solid combustibles, such

as building materials, paper or

cardboard, a safe distance away

from the heater as recommended

by the instructions. Never use

the heater in spaces which do or

may contain volatile or airborne

combustibles or products such

as gasoline, solvents, paint thin-

ner, dust particles or unknown

chemicals.

WARNING: Not for home or

recreational vehicle use.

For use with Propane/LP gas only.

The heater is designed for use as a con-

struction heater in accordance with ANSI

Z83.7•CGA2.14. Other standards govern

the use of fuel gases and heating products

for specic uses. Your local authority can

advise you about these. The primary purpose

of construction heaters is to provide tempo-

rary heating of buildings under construction,

alteration or repair. Properly used, the heater

provides safe economical heating. Products

of combustion are vented into the area being

heated.

We cannot foresee every use which may be

made of our heaters. Check with your local

re safety authority if you have questions

about heater use.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Some people

are more affected by carbon monoxide than

others. Early signs of carbon monoxide poi-

soning resemble the ﬂu, with headaches, diz-

www.usaprocom.com

160448-01C4

SAFETY

11. Do not use heater in basement or below

ground level. Propane gas is heavier than

air. If a leak occurs, propane gas will sink

to the lowest possible level.

12. Keep appliance area clear and free from

combustible materials, gasoline, paint

thinner and other ﬂammable vapors and

liquids.

13. Do not use heater in areas with high dust

content. Dust is combustible.

14. Minimum heater clearances from com-

bustibles:

Outlet: 8 Ft. (2.44 m)

Sides: 2 Ft. (0.61 m), Top: 6 Ft. (1.83 m)

Rear: 2 Ft. (0.61 m)

Locate 10 ft. (3 m) from canvas or plastic

tarpaulins or similar coverings and secure

them to prevent ﬂapping or movement due

to wind action.

15. Keep heater at least 6 feet (1.83 m) from

propane tank(s) in USA or 10 feet (3 m)

from propane tank(s) in Canada. Do not

point heater at a propane/LP tank within

20 feet (6.1 m).

16. Keep propane tank(s) below 100° F

(37.8° C).

17. Check heater for damage before each

use. Do not use a damaged heater.

18. Check hose before each use of heater.

If highly worn or cut, replace with hose

specied by manufacturer before using

heater.

19. Locate heater on a stable and level surface.

Do not move while heater is hot or running.

Position heater properly before use.

20. Not intended for use on nished ﬂoors.

21. Never block air inlet (rear) or air outlet

(front) of heater.

22. Do not leave heater unattended.

23.

Keep children and animals away from heater.

24. Never move, handle or service a hot, op-

erating or plugged-in heater. Severe burns

may result. You must wait 15 minutes after

turning heater off.

25. To prevent injury, wear gloves when han-

dling heater.

26. Never attach duct work to front or rear of

heater.

27. Do not alter heater. Keep heater in its

original state.

28. Do not use heater if altered.

29. Turn off propane supply and unplug heater

when not in use.

30. Use only original replacement parts. This

heater must use design-specic parts.

Do not substitute or use generic parts.

Improper replacement parts could cause

serious or fatal injuries.

UNPACKING

1. Remove all packing items applied to

heater for shipment. Keep plastic cover

caps (attached to inlet connector and

hose/regulator assembly) for storage.

2. Remove all items from carton.

3. Check all items for shipping damage. If

heater is damaged, call our customer

service department at 1-866-573-0674.

PRODUCT IDENTIFICATION

Hot Air Outlet

(Front)

Outer Shell

Motor

Power Cord

Piezo Ignitor

Button

Automatic Control

Valve Button

Hose/

Regulator

Assembly

Handle

Figure 1 - 40,000 Btu/Hr Model Shown

www.usaprocom.com

5160448-01C

INSTALLATION

Figure 2 - Cross Section Operational View

Air For Combustion

Air For Heating

Clean Heated

Air Out (Front)

Fan

Motor

Cool

Air In

(Back)

Combustion

Chamber

Hose/Regulator

Assembly

THEORY OF OPERATION

The Fuel System: The hose/regulator as-

sembly attaches to the propane gas supply.

This provides fuel to the heater.

The Air System: The motor turns the fan. The

fan pushes air into and around the combustion

chamber. This air is heated and provides a

stream of clean, hot air.

The Ignition System: The piezo ignitor lights

the burner.

The Automatic Control System: This system

causes the heater to shut down if the ﬂame

goes out.

PROPANE SUPPLY

Propane gas and propane tank(s) are to be

furnished by the user.

Use this heater only with a propane vapor

withdrawal supply system. See Chapter 5

of the Standard for Storage and Handling of

Liqueed Petroleum Gas, ANSI/NFPA 58 and/

or CAN/CGA B149.2. Your local library or re

department will have this booklet.

The amount of propane gas ready for use

from propane tanks varies. Two factors decide

this amount:

1. The amount of propane gas in tank(s)

2. The temperature of tank(s)

This heater is designed to operate with a

minimum 20 lb (9 kg) propane tank. You may

need two or more tanks or one larger tank in

colder weather. It is recommended you use a

100 lb (45 kg) tank for longer operation. See

chart below. Less gas is vaporized at lower

temperatures. Your local propane gas dealer

will help you select the proper supply system.

The minimum surrounding air temperature

rating for each heater is 0° F (-18° C).

Average Temp No. Of Tanks

At Tank Location 100 lb (45 kg)

Above 0° F (-18° C) 1

Below 0° F (-18° C) 2

WARNING: Review and un-

derstand the warnings in the

Safety, page 3. They are needed

to safely operate this heater. Fol-

low all local codes when using

this heater.

WARNING: Test all gas piping

and connections for leaks after

installation or servicing. Never

use an open ame to check for

a leak. Apply a noncorrosive

leak detection uid to all joints.

Bubbles forming show a leak.

Correct all leaks at once.

www.usaprocom.com

160448-01C6

1. Provide propane supply system (see

Propane Supply, page 5).

2. Connect POL tting on hose/regulator

assembly to propane tank(s). Turn POL

tting counterclockwise into threads on

tank. Tighten rmly using wrench.

IMPORTANT: Position regulator so that

hose leaving the regulator is in a hori-

zontal position (see Figure 3). This places

the regulator vent in the proper position to

protect it from the weather.

3. Connect hose to valve inlet (see Figure

4). Tighten rmly using a wrench.

IMPORTANT: Use extra hose or piping

if needed. Install extra hose or piping

between hose/regulator assembly and

propane tank. You must use the regulator

supplied with heater.

4. Open propane supply valve on propane

tank(s) slowly. Note: If not opened slowly,

excess-ow check valve on propane tank

will stop gas ow. You may hear a click

from the excess-ow check valve closing.

If this happens, reset the excess-ow

check valve by closing propane supply

valve and open again slowly.

Figure 4 - Hose and Inlet Connector

Hose

Inlet Connector

INSTALLATION

Figure 3 - Regulator Position

Figure 5 - Attaching Base Feet

Model PCFA40

Figure 6 - Adjusting Heater Height

Model PCFA60V

Propane

Tank

Propane Supply

Valve

Regulator

Support

Bracket

Fastener

Hose

POL

Fitting

5. Check all connections for leaks. Apply

mixture of liquid soap and water to gas

joints. Bubbles forming show a leak that

must be corrected.

6. Close propane supply valve.

BASE FEET (PCFA40 ONLY)

1. Locate 2 rubber feet and 2 screws in

hardware package.

2. Attach to bottom of base as shown in

Figure 5.

SUPPORT BRACKET

(PCFA60V ONLY)

To adjust the height of the front of the heater,

unscrew the fastener securing the support

bracket. Adjust bracket to desired height and

tighten fastener.

www.usaprocom.com

7160448-01C

VENTILATION

WARNING: Provide at least a 1.5 ft

2

(0.46 m

2

) opening of fresh,

outside air while running heater. If proper fresh, outside air ventila-

tion is not provided, carbon monoxide poisoning can occur. Provide

proper fresh, outside air ventilation before running heater.

OPERATION

Inlet Connector

Figure 7 - Automatic Control Valve

Button and Piezo Ignitor

(40,000 Btu/Hr Models)

Figure 8 - Fuel Button and Fuel Control

Knob (60,000 Btu/Hr Models)

Ignitor

Button

Automatic Control

Valve Button

Fuel Button

Control

Knob

WARNING: Review and un-

derstand the warnings in the

Safety, page 3. They are needed

to safely operate this heater. Fol-

low all local codes when using

this heater.

TO START HEATER

1. Follow all installation, ventilation and

safety information.

2. Locate heater on stable and level surface.

Make sure strong drafts do not blow into

front or rear of heater.

3. Plug power cord of heater into a three-

prong, grounded extension cord. Exten-

sion cord must be at least 6 feet long.

Extension cord must be UL listed.

Extension Cord Wire Size Requirements

Up to 50 ft (15.24 m) long, use 18 AWG

rated cord.

51 to 100 ft (15.54 to 30.48 m) long, use

16 AWG rated cord.

101 to 200 ft (30.78 to 60.96 m) long, use

14 AWG rated cord.

4. Plug extension cord into a 120 volt/60

hertz, 3-hole, grounded outlet. Motor will

start. Fan will turn, forcing air out front of

heater.

5. Open propane supply valve on propane

tank(s) slowly. Note: If not opened slowly,

excess-ow check valve on propane tank

will stop gas ow. You may hear a click

from the excess-ow check valve closing.

If this happens, reset the excess-ow

check valve by closing propane supply

valve and open again slowly.

WARNING: Be sure motor and

fan are running before pushing

in automatic control valve but-

ton. Flames could ash outside

heater if motor and fan are not

running.

6. 40,000 Btu/Hr Models Push in and hold

automatic control valve button (see Figure

7). Push piezo ignitor button (see Figure

7). Keep pushing ignitor button until the

burner lights. When burner lights, keep

automatic control valve button pushed

in. Release button after 30 seconds. This

activates the automatic control system.

60,000 Btu/Hr Models Press fuel but-

ton. After heater ignites, continue to hold

fuel button pressed for 15 seconds, then

release. Adjust burn rate with knob.

www.usaprocom.com

160448-01C8

MAINTENANCE

WARNINGS

• Never service heater while it

is plugged in, connected to

propane supply, operating or

hot. Severe burns and electri-

cal shock can occur.

• Keep heater clear and free

from combustible materials,

gasoline and other ammable

vapors and liquids.

• Do not block the ow of com-

bustion or ventilation air.

1. Keep heater clean. Clean heater annually

or as needed to remove dust and debris. If

heater is dirty or dusty, clean heater with

a damp cloth. Use household cleaners on

difcult spots.

2. Inspect heater before each use. Check

connections for leaks. Apply mixture of

liquid soap and water to connections.

Bubbles forming show a leak. Correct all

leaks at once.

3.

Inspect hose/regulator assembly before

each use. If hose is highly worn or cut, re-

place with hose specied by manufacturer.

4. Have heater inspected yearly by a quali-

ed service agency.

5. Keep inside of heater free from combustible

and foreign objects. Remove motor and

other internal parts if needed to clean inside

of heater (see Service Procedures, page 9).

6. Clean fan blades each season or as

needed (see Fan, page 9).

STORAGE

CAUTION: Disconnect heater

from propane supply tank(s).

1. The heater should be inspected before

each use and at least annually by a quali-

ed person.

2. Before each use, check the soft "O" ring

seat at the bullnose of the POL tting. If

the "O" ring is cut, scuffed or otherwise

damaged, replace the POL tting.

3. When heater is not in use, the gas shall

be turned off at the propane/LP gas sup-

ply cylinder(s) by closing the valve on the

cylinder.

4. Heater is to be stored indoors. The con-

nection between propane/LP gas supply

cylinder(s) and heater must be disconnect-

ed, cylinder(s) removed from the heater

and stored outdoors in accordance with

Chapter 5 of the Standard for Storage and

Handling of Liqueed Petroleum Gases

ANSI/NFPA 58 and CSA B149.1, Natural

Gas and Propane Installation Code.

5. Store in a dry, clean and safe place.

OPERATION

Note: If heater fails to ignite, hose may

have air in it. If so, keep automatic control

valve button pressed and wait 20 sec-

onds. Release automatic control valve

button and wait 20 seconds for unburned

fuel to exit heater. Repeat this step.

NOTICE: If heater is unplugged or

power outage occurs while heater

is running, the thermal limit device

will stop fuel ow. A few seconds

occur before the thermal limit de-

vice activates. During this short

time, ames may appear outside

the heater. This is normal. The

ames will go out when thermal

limit device activates.

TO STOP HEATER

1. Tightly close propane supply valve on

propane tank(s).

2. Wait a few seconds. Heater will burn gas

left in supply hose.

3. Unplug heater.

TO RESTART HEATER

1. Wait ve minutes after stopping heater.

2. Repeat steps under To Start Heater,

page 7.

www.usaprocom.com

9160448-01C

Figure 9 - Removing/Replacing Motor

and Fan Guard from Heater

Figure 10 - Setscrew Location

Setscrew

SERVICE PROCEDURES

WARNING: Never service

heater while it is plugged in,

connected to propane supply,

operating or hot. Severe burns

and electrical shock can occur.

ELECTRICAL SYSTEM

(PCFA40 ONLY)

The entire electrical system for this heater is con-

tained within the motor. If any part of the electrical

system is damaged, you must replace motor.

MOTOR

1. Remove three screws that attach fan

guard to heater shell.

2. Remove motor and fan guard from heater

shell (see Figure 9).

3. Use hex wrench to loosen set screw which

holds fan to motor shaft (see Figure 10).

Remove fan. Be careful not to damage

the fan blade pitch.

4.

Remove two nuts and two screws that attach

fan guard to motor using nut-driver. Remove

fan guard from motor (see Figure 11).

5. 60,000 BTU/Hr Model Only Remove bot-

tom panel to gain access to terminal block.

6. Remove fan wires from terminal block.

7. Disconnect the green power cord wire

from motor and remove black and white

wire terminals.

8. Discard old motor.

9. Attach green power cord wire to motor.

10. Attach fan guard to new motor with two

nuts and two screws.

11. Replace black and white terminals.

12. Place fan onto motor shaft of new mo-

tor. Make sure set screw contacts ﬂat

Screw

Motor and

Fan Guard

Figure 11 - Removing or Attaching Fan

Guard from Motor

Fan

Guard

Motor

Screw

surface on motor shaft. Tighten set screw

rmly (40-50 inch-pounds [46.08-57.60

kilogram-centimeters]).

13. Place motor and fan guard into rear of

heater shell. Make sure power cord is

properly located.

14. Insert three screws through heater shell

and into fan guard (see Figure 9). Tighten

screws rmly.

FAN

1. Remove three screws that attach fan

guard to heater shell.

2. Remove motor and fan guard from heater

shell (see Figure 9).

3. Use hex wrench to loosen set screw that

holds fan to motor shaft (see Figure 10).

4. Remove fan. Be careful not to damage

the fan blade pitch.

5a. If replacing fan, remove old fan and dis-

card. Go to step 7.

5b. If cleaning fan, use soft cloth moistened

with kerosene or solvent.

6. Dry fan thoroughly.

7. Place fan onto motor shaft. Make sure

set screw contacts ﬂat surface on motor

shaft. Tighten set screw firmly (40-50

inch-pounds [46.08-57.60 kg-cm]).

8. Place motor and fan guard into rear of

heater shell. Make sure power cord is

properly located (see Figure 9).

9. Insert three screws through heater shell

and into fan guard. Tighten screws rmly.

www.usaprocom.com

160448-01C10

Figure 13 - Removing Ignitor Mounting

Screw and Ignitor

Ignitor

Mounting

Screw

Figure 14 - Clearance Between Ignitor

Electrode and Target Plate

Ignitor Electrode

Gap

Area

SERVICE PROCEDURES

IGNITOR (PCFA40 ONLY)

1. Remove motor and fan guard from heater

(see Motor, page 9, steps 1 and 2).

2. Remove black ignitor wire from piezo

ignitor. Access ignitor wire through under-

side of heater base (see Figure 12). Push

wire up through notch in ller panel.

3. Remove ignitor mounting screw from

rear head using nut-driver or standard

screwdriver (see Figure 13).

4. Remove ignitor from rear head.

5. Install new ignitor. Attach ignitor to rear

head with ignitor mounting screw.

6. Run ignitor wire from new ignitor through

notch in ller panel. Attach ignitor wire to

piezo ignitor.

7. Set gap between ignitor electrode and

target plate to 0.17" (43.18 cm) (see

Figure 14).

WARNING: Make sure heater

is disconnected from propane

supply. Heater could ignite caus-

ing severe burns.

8. Test for spark. Push piezo ignitor button

and watch for spark between ignitor elec-

trode and target plate.

9. Place motor and fan guard into rear of

heater shell (see Motor, page 9, steps 9

and 10).

Figure 12 - Removing Ignitor Wire from

Piezo Ignitor

Ignitor Wire

Piezo Ignitor

Underside

of Heater

www.usaprocom.com

11160448-01C

TROUBLESHOOTING

WARNING: Never service heater while it is plugged in, connected

to propane supply, operating or hot. Severe burns and electrical

shock can occur.

WARNING: Use only in areas free of high dust content.

Problem Possible Cause Corrective Action

Fan does not turn when

heater is plugged in.

1. No electrical power to heater.

2. Fan hitting inside of heater

shell.

3. Fan blades bent.

4. Defective motor.

1. Check voltage to electrical

outlet. If voltage is good,

check heater power cord for

breaks.

2. Adjust motor/fan guard to

keep fan from hitting inside

of heater shell. Bend fan

guard if necessary.

3. Replace fan. See Fan, page

9.

4. Replace motor. See Motor,

page 9.

Heater will not ignite. 1. User did not follow installa-

tion or operation instructions

properly.

2. No spark at ignitor. To test

for spark, follow step 8 under

Ignitor, page 10. If you see

spark at ignitor, have heater

serviced by qualied service

person. If no spark seen:

A) Loose or disconnected

ignitor wire

B) Wrong spark gap

C) Piezo ignitor loose

D) Bad ignitor electrode

1. Repeat installation and op-

eration instructions. See

Installation, page 5 and

Operation, page 7.

2. A) Check ignitor wire. Tight-

en or reattach loose ignitor

wire. See Figure 11, page 8

for ignitor wire location

B) Set gap between ignitor

electrode and target plate to

0.17" (0.43 cm)

C) Tighten nut holding piezo

ignitor to base of heater

D) Replace ignitor electrode.

See Ignitor, page 10

Heater shuts down while

running.

1. High surrounding air tem-

perature causing thermal

limit device to shut down

heater.

2. Restricted air ﬂow.

3. Damaged fan.

4. Excessive dust or debris in

surrounding area.

1. This can happen when run-

ning heater in temperatures

above 85° F (29.44° C). Run

heater in cooler tempera-

tures.

2 Check heater inlet and out-

let. Remove any obstruc-

tions.

3. Replace fan. See Fan, page 9.

4. Clean heater. See Mainte-

nance, page 8.

www.usaprocom.com

160448-01C12

PARTS

MODEL PCFA40

2

12

13

14

15

16

17

18

4

6

5

8

7

1

3

10

11

9

19

www.usaprocom.com

13160448-01C

PARTS

MODEL PCFA40

This list contains replaceable parts used in your heater. When ordering parts, follow the

instructions listed under Replacement Parts on page 17 of this manual.

Item Part # Description Qty

1 ** Combustion Chamber 1

2 160334-01 Handle 1

3 160335-01BK Handle Bracket 2

4 160321-01 Fan 1

5 160317-02 Motor 1

6 160319-01BK Motor Mounting Bracket 1

7 PF06-1201-D Strain Relief Bushing 1

8 160318-02 Power Cord 1

9 160323-01 Piezo Ignitor 1

10 160325-01 Electrode Ignitor 1

11 160278-01 Screw 1

12 ** Rear Head 1

13 160440-01 Thermostat Switch 1

14 160331-01 Wire Assembly 1

15 160449-01 Thermocouple 1

16 160327-01 Burner Assembly 1

17 160326-01 Main Orice Valve 1

18 160265-01 Palnut Fastener 1

19 160331-05 Ignitor Wire 1

PARTS AVAILABLE - NOT SHOWN

160451-01 Operation/Model Data Decal 1

160452-01 Operation Decal (Spanish/French) 1

160332-01 Hose/Regulator Assembly 1

** Not a eld replaceable part.

www.usaprocom.com

160448-01C14

PARTS

MODEL PCFA60V

8

7

2

3

4

5

10

9

6

1

11

12

15

16

17

18

21

22

23

24

19

13

14

27

26

25

20

www.usaprocom.com

15160448-01C

Item Part # Description Qty

1 ** Combustion Chamber 1

2 160334-01 Handle 1

3 160335-01BK Handle Bracket 2

4 160456-01 Fan 1

5 160317-01 Motor 1

6 160463-01BK Motor Mounting Bracket 1

7 PF06-1201-C Strain Relief Bushing 1

8 160318-01 Power Cord 1

9 ** Support Bracket 1

10 ** Fastener Screw 1

11 ** Rear Head 1

12 160440-02 Thermostat Switch 1

13 160481-01 Electrode Ignitor 1

14 160278-01 Screw 1

15 160482-01 Burner Assembly 1

16 160474-01 Injector, 0.034 1

17 160508-01 Female Elbow 1

18 160449-02 Thermocouple 1

19 160480-02 Tube 1

20 160478-01 Female Compression Fitting 1

21 160304-03 Control Knob 1

22 160477-01 Brass Adaptor 1

23 160476-01 Control Valve 1

24 160294-06 Ball Valve Assembly 1

25 160479-01 Relay Assembly 1

26 160485-01 Ignitor Assembly 1

27 160483-01 Terminal Block 1

PARTS AVAILABLE - NOT SHOWN

160492-01 Operation/Model Data Decal 1

160491-01 Operation Decal (Spanish/French) 1

160468-01 Hose/Regulator Assembly 1

** Not a eld replaceable part.

PARTS

MODEL PCFA60V

This list contains replaceable parts used in your heater. When ordering parts, follow the

instructions listed under Replacement Parts on page 17 of this manual.

www.usaprocom.com

160448-01C16

WIRING DIAGRAM

60,000 BTU/HR MODEL ONLY

160518-01A

Black** or Orange**/

Negro** o Naranja**/

Noir** ou orange**

L1

L2

White/Blanco/

Blanc

Blue*/Azul*/Bleu*

Blue/Azul/Bleu

White/Blanco/

Blanc

White/Blanco/Blanc

Black/

Negro/Noir

Black/Negro/Noir

Green/

Verde/

Vert

Orange/

Naranja

Orange/

Naranja

Orange/

Naranja

Orange/

Naranja

Thermocouple/Termopar

CONNECTION DIAGRAM/DIAGRAMA DE CONEXIONES/

DIAGRAMME DE CONNEXION

SCHEMATIC DIAGRAM/DIAGRAMA ESQUEMÁTICO/

DIAGRAMME DE CIRCUIT

60,000/125,000/175,000 Models/Modelos

Relay/Relé/Relais

Motor/

Moteur

Ignitor/

Encendedor/

Allumeur

High-Limit Switch/

Interruptor de

límite alto/

Commutateur de

limite supérieure

• If any original wiring as supplied with the heater must be replaced, it must be replaced with type AWG 105° C

wire or its equivalent except as indicated (*Type SF2-200. **UL Style 3257 250° C)

• Si es necesario reemplazar algún cable suministrado originalmente con el calentador, éste se debe reemplazar con

cable tipo AWG 105° C o su equivalente, excepto cuando se indica lo contrario (*Tipo SF2-200. **UL Style 3257 250° C)

* Si le câblage fourni avec l'appareil de chauffage doit être remplacé, faites-le avec du câble de type AWG 105° C

ou son équivalent, sauf indication contraire (*Type SF2-200. **UL Style 3257 250° C)

Line Cord/

Cable de línea/

Cordon électrique

Motor/

Moteur

High Limit Switch/

Interruptor de límite alto/

Interrupteur de

limite supérieure

White/Blanco/Blanc

Black/Negro/Noir

115V

60HZ

Gas

Valve

Relay/

Relé/

Relais

Thermocouple/

Termopar

Green/Verde/Vert

L1

L2

Ignitor/

Encendedor/

Allumeur

Válvula de gas/

Robinet de gaz

Electrode/Electrodo/

Électrode

Electrode/Electrodo/

Électrode

• Label all wires prior to disconnecting.

www.usaprocom.com

17160448-01C

REPLACEMENT PARTS

Note: Use only original replacement parts. This will protect your warranty coverage for parts

replaced under warranty.

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product.

If they can’t supply original replacement

part(s) call Customer Service toll free at

1-866-573-0674 for referral information.

When calling Customer Service have ready:

• Model number of your heater

• The replacement part number

PARTS UNDER WARRANTY

Contact authorized dealers of this product.

If they can’t supply original replacement

parts, call Customer Service toll free at

1-866-573-0674 for referral information.

When calling Customer Service or your

dealer, have ready:

• Your name

• Your address

• Model and serial number of your heater

• How heater was malfunctioning

• Type of gas supply and Propane/LP tank

size

• Purchase date

Usually, we will ask you to return the defective

part to the factory

ACCESSORIES

Purchase these accessories from your local dealer. If they can not supply these accessories,

call ProCom Heating, Inc. at 1-866-573-0674 for information.

TECHNICAL SERVICES

You may have further questions about installation, operation, or troubleshooting. If so, contact

ProCom Heating, Inc. at 1-866-573-0674. When calling please have your model and serial

numbers of your heater ready.

You can also visit ProCom Heating, Inc.’s web site at www.usaprocom.com.

www.usaprocom.com

160448-01C18

NOTES

________________________________________________________________________

www.usaprocom.com

19160448-01C

NOTES

________________________________________________________________________

160448-01

Rev. C

07/15

REGISTER YOUR PRODUCT AT WWW.USAPROCOM.COM

PROCOM HEATING, INC. LIMITED WARRANTIES

New Products – Outdoor Heating

Standard Warranty: ProCom Heating, Inc. warrants this new product and any parts thereof to be free from

defects in material and workmanship for a period of one (1) year from the date of rst purchase from an

authorized dealer provided the product has been installed, maintained and operated in accordance with

ProCom Heating, Inc.’s warnings and Instructions.

For products purchased for commercial, industrial or rental usage, this warranty is limited to 90 days from

the date of rst purchase.

Factory Reconditioned Products

Limited Warranty: ProCom Heating, Inc. warrants factory reconditioned products and any parts thereof to

be free from defects in material and workmanship for a period 30 days from the date of rst purchase from an

authorized dealer provided the product has been installed, maintained and operated in accordance with ProCom

Heating, Inc.’s warnings and Instructions. No return will be authorized. Parts will be provided to repair the product.

Terms Common to All Warranties

The following terms apply to all of the above warranties:

Always specify model number and serial number when contacting the manufacturer. To make a claim under

this warranty, the bill of sale or other proof of purchase must be presented.

This warranty is extended only to the original retail purchaser when purchased from an authorized dealer,

and only when installed by a qualied installer in accordance with all local codes and instructions furnished

with this product.

This warranty covers the cost of part(s) required to restore this product to proper operating condition and

an allowance for labor when provided by a ProCom Heating, Inc. Authorized Service Center or a provider

approved by ProCom Heating, Inc. Warranty parts must be obtained through authorized dealers of this

product and/or ProCom Heating, Inc. who will provide original factory replacement parts. Failure to use

original factory replacement parts will void this warranty.

Traveling, handling, transportation, diagnostic, material, labor and incidental costs associated with warranty

repairs, unless expressly covered by this warranty, are not reimbursable under this warranty and are the

responsibility of the owner.

Excluded from this warranty are products or parts that fail or become damaged due to misuse, accidents,

improper installation, lack of proper maintenance, tampering or alteration(s).

This is ProCom Heating, Inc.’s exclusive warranty, and to the full extent allowed by law; this express war-

ranty excludes any and all other warranties, express or implied, written or verbal and limits the duration of

any and all implied warranties, including warranties of merchantability and tness for a particular purpose to

one (1) year on new products and 30 days on factory reconditioned products from the date of rst purchase.

ProCom Heating, Inc. makes no other warranties regarding this product.

ProCom Heating, Inc.’s liability is limited to the purchase price of the product and ProCom Heating, Inc.

shall not be liable for any other damages whatsoever under any circumstances including direct, indirect,

incidental, or consequential damages.

Some States do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of

incidental or consequential damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.

WARRANTY

KEEP THIS WARRANTY

Model (

located on product or identication tag

) _____________________________

Serial No. (

located on product or identication tag

) __________________________

Date Purchased ______________________________________

Keep receipt for warranty verication.

ProCom Heating, Inc.

Bowling Green, KY 42101

www.usaprocom.com

1-866-573-0674

La page charge ...

ProCom Heating 200060 Mode d'emploi

Ce manuel convient également à

ProCom Heating 200060 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents