Samsung RF26HFPNBSR Manuel utilisateur

imagine the possibilities

RF261B*****

RF260B*****

RF26HFP***

Free Standing Appliance

English

Refrigerator

user manual

Thank you for purchasing this Samsung product.

DA68-02601B-14.indb 1 2018. 10. 8. 오후 5:04

02_ Safety information

safety information

SAFETY INFORMATION

• Before using your new Samsung Refrigerator,

please read this manual thoroughly to ensure

that you know how to operate the features and

functions that your new appliance oers safely

and eciently.

• This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they

have been given supervision or instruction

concerning use of the appliance by a person

responsible for their safety. Children should be

supervised to ensure that they do not play with

the appliance.

• Because the following instructions cover

various models, the characteristics of your

refrigerator may dier slightly from the

refrigerator described in this manual.

• If you have any question, contact us at

1-800-SAMSUNG or ﬁnd help and information

online at www.samsung.com.

• R-600a or R-134a is used as a refrigerant.

Check the compressor label on the rear of

the appliance or the rating label inside the

fridge to see which refrigerant is used for your

refrigerator. If this product contains ﬂammable

gas (Refrigerant R-600a), contact your local

authority in regard to safe disposal of this

product.

• It is hazardous for anyone other than an

Authorized Service Person to service this

appliance.

Warning :

Risk of ﬁre

/ ﬂammable

materials

Important safety symbols and

precautions:

WARNING

Hazards or unsafe practices that may result in

severe personal injury or death.

CAUTION

Hazards or unsafe practices that may result in

minor personal injury or property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions carefully.

Unplug the power plug from the wall socket.

Make sure the refrigerator is grounded

to prevent electric shock.

Call the contact center for help.

Note.

These warning signs are here to prevent

injury to you and others.

Please follow them carefully.

After reading this section, keep it in a safe

place for future reference.

STATE OF CALIFORNIA

PROPOSITION 65

WARNING

• Cancer and Reproductive Harm - www.

P65Warnings.ca.gov.

SEVERE WARNING SIGNS

FOR INSTALLATION

• Do not install the refrigerator in a damp

place or place where it may come in

contact with water.

- Deteriorated insulation of electrical parts may

cause an electric shock or ﬁre.

• Do not place this refrigerator in direct sunlight

or expose to the heat from stoves, room

heaters or other appliance.

• Do not plug several appliances into the same

multiple power strip. The refrigerator should

always be plugged into its own individual

electrical outlet which has a voltage rating that

matches the voltage listed on the refrigerator’s

rating plate.

- This provides the best performance and

also prevents overloading house wiring

circuits, which could cause a ﬁre hazard from

overheated wires.

• If the wall socket is loose, do not insert the

power plug.

- There is a risk of electric shock of ﬁre.

• Do not use a cord that shows cracks or

abrasion damage along its length or at either

end.

• Do not bend the power cord excessively or

place heavy articles on it.

WARNING

DA68-02601B-14.indb 2 2018. 10. 8. 오후 5:04

Safety information _03

• Do not twist or tie the power cord.

• Do not hook the power cord over a metal

object, place a heavy object on the power

cord, insert the power cord between objects,

or push the power cord into the space behind

the appliance.

- When moving the refrigerator, be careful not to

roll over or damage the power cord

- This may result in an electric shock or ﬁre.

• Never unplug your refrigerator by pulling on the

power cord. Always grip plug ﬁrmly and pull

straight out from the outlet.

- Damage to the cord may cause a short-circuit,

ﬁre and/or electric shock.

• Do not use aerosols near the refrigerator.

- Aerosols used near the refrigerator may cause

an explosion or ﬁre.

• Do not install this appliance near a heater,

inﬂammable material.

• Do not install this appliance in a humid, oily or

dusty location, in a location exposed to direct

sunlight and water (rain drops).

• Do not install this appliance in a location where

gas may leak.

- This may result in an electric shock or ﬁre.

• This refrigerator must be properly

installed and located in accordance

with the manual before you use it.

• Connect the power plug in the proper position

with the cord hanging down.

- If you connect the power plug upside down,

the wire can get cut o and cause a ﬁre or

electric shock.

• When moving the refrigerator, be careful not to

roll over or damage the power cord.

- This constitutes a ﬁre hazard.

• Make sure that the power plug is not

squashed or damaged by the back of the

refrigerator.

• Keep the packing materials out of reach of

children.

- There is a risk of death from suocation if a

child puts the packing materials on his or her

head.

• The appliance must be positioned so that the

plug is accessible after installation.

• You need to remove all the protective plastic

ﬁlm before you initially plug the product in.

• The refrigerator must be safely

grounded.

- Always make sure that you have grounded the

refrigerator before attempting to investigate

or repair any part of the appliance. Power

leakages can cause severe electric shock.

• Never use gas pipes, telephone lines or other

potential lightning attractors as an electrical

ground.

- Improper use of the grounding plug can result

in a risk of electric shock. If it is necessary

to use an extension cord, use only a 3-wire

extension cord that has a 3-blade grounding

plug and a 3-slot receptacle that will accept

the plug on the appliance. The marked rating

of the extension cord should be AC115-

120 V, 10 A, or more. If a grounding adapter

is used, make sure the receptacle box is fully

grounded.

• If the power cord is damaged,

have it replaced immediately by the

manufacturer or its service agent.

• The wall socket must be easily accessible so

that the appliance can be quickly disconnected

from the wall socket in an emergency.

• It must be outside the area of the rear of the

appliance.

• When positioning the appliance, ensure the

power cord is not trapped or damaged.

• Do not locate multiple portable socket-outlets

or portable power supplies at the rear of the

appliance.

• Do not store explosive substances such as

aerosol cans with a ﬂammable propellant in

this appliance.

INSTALLATION CAUTIONS

• Allow sucient space to install the

refrigerator on a ﬂat surface.

- If your refrigerator is not level, the internal

cooling system may not work correctly.

• Keep the ventilation space in the appliance

enclosure or mounting structure clear of

obstruction.

• Allow the appliance to stand for 2 hours after

installation.

• We recommend you have installed this refrigerator

by a qualiﬁed technician or service company.

- Failing to do so may result in an electric shock,

ﬁre, explosion, problems with the product, or

injury.

CRITICAL USAGE WARNINGS

• Do not insert the power plug with wet

hands.

• Do not store articles on the top of the appliance.

- When you open or close the door, the articles

may fall and cause personal injury and/or

material damage.

• Do not put a container ﬁlled with water on the

refrigerator.

- If spilled, there is a risk of ﬁre or electric shock.

• Children should be supervised to ensure that

they do not play with the appliance.

- Keep ﬁngers out of “pinch point” areas;

clearances between the doors and cabinet are

necessarily small. Be careful when you open

the doors when children are in the area.

• Do not let children hang on the door. A serious

injury may occur.

• Do not let children go inside the refrigerator.

Children could become trapped.

• Do not insert your hands into the bottom area

CAUTION

WARNING

DA68-02601B-14.indb 3 2018. 10. 8. 오후 5:04

04_ Safety information

under the appliance.

- Any sharp edges may cause personal injury.

• Do not let children step on a drawer’s cover.

- The drawer may break and cause them to slip.

• Do not overﬁll the refrigerator with food.

- When you open the door, an item may fall out

and cause personal injury or material damage.

• Do not touch the inside walls of the freezer or

products stored in the freezer with wet hands.

- This may cause frostbite.

• Never put ﬁngers or other objects into the water

dispenser hole, ice chute, or ice maker bucket.

- It may cause personal injury or material damage.

• Do not spray ﬂammable gas near the refrigerator.

- There is a risk of explosion or ﬁre.

• Do not store volatile or ﬂammable substances

in the refrigerator.

- The storage of benzene, thinner, alcohol, ether,

LP gas and other such products may cause

explosions.

• Do not store pharmaceuticals products,

scientiﬁc materials, or temperature sensitive

products in the refrigerator.

- Products that require strict temperature

controls must not be stored in the refrigerator.

• Do not place or use an electrical appliance

inside the refrigerator, unless it is of a type

recommended by the manufacturer.

• Do not stand on top of the appliance or place

objects (such as laundry, lighted candles,

lighted cigarettes, dishes, chemicals, metal

objects, etc.) on the appliance. This may result

in an electric shock, ﬁre, problems with the

product, or injury. Do not put a container ﬁlled

with water on the appliance.

- If spilled, there is a risk of ﬁre or electric shock.

• Do not use mechanical devices or any other

means to accelerate the defrosting process,

other than those recommended by the

manufacturer.

• Do not damage the refrigerant circuit.

• Do not spray volatile material such as

insecticide onto the surface of the appliance.

- As well as being harmful to humans, it may

also result in an electric shock, ﬁre or problems

with the product.

• Never stare directly at the UV LED lamp for

long periods of time.

- This may result in eye strain due to the

ultraviolet rays.

• Do not disassemble or repair the

refrigerator by yourself.

- You run risk of causing a ﬁre, malfunction and/

or personal injury.

- When the interior or exterior LED lamp has

gone out, please contact your service agents.

• Children should be supervised to

ensure that they do not play with the

appliance.

- Keep ﬁngers out of “pinch point” areas :

clearances between the doors and cabinet are

necessarily small. Be careful when you open

the doors when children are in the area. Do not

let children hang on the door. If not, a serious

injury may occur. Risk of children entrapment.

Do not let children enter inside the refrigerator.

• Bottles should be stored tightly together so

that they do not fall out.

• This product is intended only for the storage of

food in a domestic environment.

• If a gas leak is detected, avoid any naked

ﬂames or potential sources of ignition and air

the room in which the appliance is standing for

several minutes.

- Do not touch the appliance or power cord.

- Do not use a ventilating fan.

- A spark may result in explosion or ﬁre.

• Use only the LED Lamps provided by

manufacturer or service agent.

• If there are burning smells or smoke,

pull out power plug immediately and

contact your Samsung Electronics

service center.

• If you experience diculty when changing the

light, contact a service agent.

• If the product is equipped with LED Lamps,

do not disassemble the Lamp Cover and LED

Lamp by yourself.

- Please contact your service agents.

• If any dust or water is in refrigerator, pull out

the power plug and contact your Samsung

Electronics service center.

- Otherwise there is a risk of ﬁre.

USAGE CAUTIONS

• Do not re-freeze frozen foods that

have thawed completely. Do not place

carbonated or ﬁzzy drinks in the freezer

compartment. Do not put bottles or

glass containers in the freezer.

- When the contents freeze, the glass may break

and cause personal injury.

• Use only the ice maker provided with

the refrigerator. The water supply to this

refrigerator must only be installed/connected

by a suitably qualiﬁed person and connected

to a potable water supply only. In order to

operate the ice maker properly, water pressure

of 20 ~ 125 psi is required. If you have a long

vacation or business trip and won’t use water

or ice dispensers, close the water valve.

- Otherwise, water leakage may occur.

• Wipe excess moisture from the inside and

leave the doors open.

- Otherwise, odor and mold may develop.

• Service warranty and Modiﬁcation.

- Any changes or modiﬁcations performed by

a 3rd party on this ﬁnished appliance are not

covered under Samsung warranty service, nor

can Samsung be responsible for safety issues

that result from 3rd party modiﬁcations.

CAUTION

DA68-02601B-14.indb 4 2018. 10. 8. 오후 5:04

Safety information _05

• Do not block air holes.

- If the air holes are blocked, especially with

a plastic bag, the refrigerator can be over

cooled. If this cooling period lasts too long, the

water ﬁlter may break and cause water leakage.

• If the refrigerator is disconnected from the

power supply, you should wait for at least ﬁve

minutes before plugging it back in.

• If you have a long vacation planned or the

refrigerator is not to be used for a long period

of time, you must empty the refrigerator and

pull out the power plug.

- Letting the refrigerator run for a long time

without using it can cause the insulation to

deteriorate and may cause a ﬁre.

- Wipe excess moisture from the inside and

leave the doors open. Otherwise, odor and

mold may develop.

• To get the best performance from the product:

- Do not place foods too close to the vents at

the rear of the appliance as it can obstruct free

air circulation in the refrigerator compartment.

- Wrap food up properly or place it in airtight

containers before putting it into the refrigerator.

• Fill the water tank, ice tray, and water cubes

only with potable water.

• If the product is ﬂooded, make sure to

contact your nearest service center.

- There is a risk of electric shock or ﬁre.

CLEANING CAUTIONS

• Do not directly spray water on the

inside or outside the refrigerator.

- There is a risk of ﬁre or electric shock.

• Do not use a hair dryer to dry the inside of the

refrigerator. Do not place a lighted candle in

the refrigerator to remove bad odors.

- This may result in an electric shock or ﬁre.

• Remove any foreign matter or dust

from the power plug pins. Do not use

a wet or damp cloth when cleaning

the plug.

- Otherwise, there is a risk of ﬁre or electric shock.

• Unplug the refrigerator before cleaning

or making repairs.

CAUTION

CRITICAL DISPOSAL

WARNINGS

• Risk of child entrapment. Before you

throw away your old refrigerator or

freezer:

- Take o the doors.

- Leave the shelves in place so that children may

not easily climb inside.

• Please dispose of the packaging material from

this product in an environmentally friendly manner.

• Leave the shelves in place so that children

can not easily climb inside. Ensure that none

of the pipes on the back of the appliance are

damaged prior to disposal.

• R600a or R134a is used as a refrigerant.

Check the compressor label on the rear of

the appliance or the rating label inside the

fridge to see which refrigerant is used for your

refrigerator. If this product contains ﬂammable

gas (Refrigerant R600a), contact your local

authority in regard to safe disposal of this product.

• When disposing of this refrigerator, remove the

door/door seals and door latch so that small

children or animals cannot become trapped

inside. Children should be supervised

to

ensure that they do not play with the appliance.

• Cyclopentane is used in the insulation. The

gases in the insulation material require a

special disposal procedure. Please contact

your local authorities in regard to the

environmentally safe disposal of this product.

Ensure that none of the pipes on the back of

the refrigerator are damaged prior to disposal.

THIS APPLIANCE IS INTENDED

TO BE USED IN HOUSEHOLD

AND SIMILAR APPLICATIONS

SUCH AS

• sta kitchen areas in shops, oces and other

working environments;

• farm houses and by clients in hotels, motels

and other residential type environments;

• bed and breakfast type environments;

• catering and similar non-retail applications.

WARNING

contents

SETTING UP YOUR FRENCH DOOR REFRIGERATOR ………………………………… 06

OPERATING YOUR FRENCH DOOR REFRIGERATOR …………………………………… 13

TROUBLESHOOTING ………………………………………………………………………… 24

DA68-02601B-14.indb 5 2018. 10. 8. 오후 5:04

6_ setting up

Setting up your French Door

Refrigerator

GETTING READY TO INSTALL

THE REFRIGERATOR

Congratulations on your purchase of this Samsung

French Door Refrigerator.

We hope you enjoy the state-of-art features and

eciencies that this new appliance oers.

Selecting the best location for the refrigerator

Choose:

• A location with easy access to a water supply.

• A location without direct exposure to sunlight.

• A location with a level ﬂoor.

• A location with enough space for the

refrigerator doors to open easily.

• A location that allows sucient space to the

right, left, back and top for air circulation.

• A location that allows you to move the

refrigerator easily if it needs maintenance or

service.

• Do not install the refrigerator where the

temperature will go below 50 ºF (10 ºC).

• Do not locate the refrigerator where it may

become wet.

When moving your refrigerator

To prevent ﬂoor damage, be sure the

front adjusting legs are in the up position

(above the ﬂoor). Refer to ‘Adjusting the

Level’ in the manual (on page 10).

Flat-blade screw

driver(-)

Control Lever

CAUTION

B

A

C

E

D

B

A

C

E

D

Model RF263T**/ RF263B**

Depth “A” 33 1/2” (850mm)

Width “B” 35 3/4” (909mm)

Height “C” 68 3/8” (1737mm)

Overall Height “D” 70” (1778mm)

Depth “E” 35 3/4” (910mm)

63 3/4

”

(1620 mm)

13 3/8”

(340 mm)

140° 140°

2”

(50 mm)

35 3/4”

(909 mm)

29 1/4”

(745 mm)

48 ”

(1220 mm)

1 5/8”

(40 mm)

3 3/4”

(95 mm)

• The measurements here are based on

the design dimension, which may dier

depending on the measuring method.

DA68-02601B-14.indb 6 2018. 10. 8. 오후 5:04

setting up _7

01 SETTING UP

FLOORING

For proper installation, you must place this

refrigerator on a level, hard surface that is the

same height as the rest of the ﬂoor. This surface

should be strong enough to support a fully loaded

refrigerator, or approximately 335lbs (152kg).

To protect the ﬁnish of the ﬂooring, cut a large

section of the cardboard carton and place it under

the refrigerator where you are working. When

moving the refrigerator, you need to pull and push

it straight forwards or back. Do not wiggle it from

side to side.

REQUIRED TOOLS

Required Tools (Not provided)

You need the following tools to complete the

installation of your refrigerator:

Philips

screwdriver(+)

Flat-blade screw

driver(-)

Socket wrench

(10mm)

Allen wrench

(3/16”) (5mm)

REMOVING THE REFRIGERATOR

DOORS

For some installations you need to remove the

fridge and freezer drawers so you can move the

refrigerator to its ﬁnal location. Do not remove

the doors/drawer if you don’t need to. If you

do not need to remove the refrigerator doors, go

to Adjusting the Level on page 10. If you need to

remove the doors. continue below.

Before removing the door/drawer, make sure you

read the following items:

Disconnect power to the refrigerator

before removing the door or drawer.

• Be careful not to drop, damage or

scratch the door/drawer while removing

them.

• Use care when you remove the doors/drawer.

The doors are heavy and you could injure

yourself.

• Reattach the doors/drawer properly to avoid:

- Moisture from air leakage.

- Uneven door alignment.

- Wasting energy due to improper door seal.

HOW TO ASSEMBLE THE HANDLE

Orient each handle so that the end with the sticker

attached is at the top and the holes with the

tightening screws are facing each other.

Then, follow the directions below to install each

handle.

By using Phillips screwdriver, ﬁx the screw

(optional) and then put the handle on the ﬁxer by

sliding them down ﬁrmly.

WARNING

DA68-02601B-14.indb 7 2018. 10. 8. 오후 5:04

8_ setting up

2

1

3

5

4

Fix the handles to the doors

by sliding them down ﬁrmly.

Screw

Tighten with wrench ﬁrmly

Drawer door handle assembly

Check the direction of

Handle assembly.

1

2

Fix the handles to the

doors by sliding them

side ﬁrmly.

3

Fix the handles to the doors by sliding them left

side ﬁrmly.

4

5

Tilt up the Handle bar and tighten with wrench ﬁrmly.

Disassembling the refrigerator doors

Be careful not to drop and scratch the

doors while removing them.

With the door opened

1. Remove the 3 screws holding down the TOP

TABLE ( 1 ) and turn it with wires connected.

1

2. Disconnect two connecto r ( 2 ) on the left side

door. To remove the water coupler from the

hinge, twist and pull it from the hinge.

2

WARNING

DA68-02601B-14.indb 8 2018. 10. 8. 오후 5:04

setting up _9

01 SETTING UP

3. Pull and remove the hinge lever ( 3 ) . Remove

the ground screw ( 4 ) attached to the upper

left door hinges with a philips screwdriver (+).

Remove the upper left and right door hinges

( 5 ).

3

4

5

4. Lift the door straight up to remove.

5. Remove the screw ( 6 ) attached to the

lower left and right door hinges with a philips

screwdriver (+). Remove the 2 hex head bolts

( 7 ) attached to the lower left and right door

hinges with an allen wrench (3/16”). Remove

the lower left and right door hinges ( 8 ).

8

6

7

Allen wrench

DISASSEMBLING THE FLEX DOOR

1. Take out the upper drawer by lifting it up.

2. Take out the lower basket ( 1 ) by lifting the

basket up from the rail system.

1

3. Press the ﬁxing hook of rail system.

4. Holding the top of the Freezer Drawer, pull it out all

the way and then remove it from the rail system.

Be careful not to scratch or dent the

sliding rail by letting it strike the ﬂoor.

Make sure that you mount the freezer

basket in the right position when

removing / installing the freezer door.

Failing to do so may result in the door not

opening or closing properly.

Do not overload the bottom basket or

the top drawer. Overloading prevents the

Freezer drawer from closing properly and

will eventually cause frost build-up.

CAUTION

DA68-02601B-14.indb 9 2018. 10. 8. 오후 5:04

10_ setting up

ASSEMBLE THE FREEZER

DRAWER

To reattach the drawer after you have moved the

fridge to its ﬁnal location, assemble the parts in

reverse order.

ADJUSTING THE LEVEL

Make sure the refrigerator is level so that you can

make ﬁnal adjustments. Use a level to test if the

refrigerator is level both side to side and back to

front. If the refrigerator is not level, it will not be

possible to get the doors perfectly even, which

may cause moisture condensation and increased

energy bills. Below is an example of how to level

the refrigerator if the left side of the refrigerator is

lower than the right side.

How to adjust the level

1. Open the freezer drawer and remove the lower

basket.

2. Insert a ﬂat-blade screwdriver (-) into the

notch on the left control lever, and then turn

it counter-clockwise to level the refrigerator.

(You turn the lever clockwise to lower the

refrigerator and counterclockwise to raise it.)

ﬂat-blade screwdriver (-) Control Lever

Both control levers must be touching the

ﬂoor to avoid possible personal injury or

property damage because of tipping.

• If the right side is lower, perform the

same procedure, but with the right

control lever.

• It is dicult to remove the cover leg

front from the refrigerator, so we do not

recommend making small adjustments

with the control lever. Instead, refer to

the next page for the best way to make

minor adjustments to the doors.

CAUTION

MAKING MINOR ADJUSTMENTS

BETWEEN DOORS

Remember, a leveled refrigerator is necessary

for getting the doors perfectly even. If you need

help, review the previous section on leveling the

refrigerator.

Adjustment

part

Fixed part

• The left door is ﬁxed. To make minor

adjustments between doors, adjust only

the right door.

1. Pull out the freezer drawer ( 1 ), then you can

see the lower hinge ( 2 ).

2. Insert a philips screwdriver (+) ( 3 ) into the

shaft ( 4 ) of the lower hinge.

3. Adjust the height by turning a philips

screwdriver (+) ( 3 ) clockwise (

DOWN

) or

counterclockwise (

UP

).

• When you turn a philips screwdriver (+)

counterclockwise (

UP

), the door will

move up.

1

2

3

4

3

DA68-02601B-14.indb 10 2018. 10. 8. 오후 5:04

setting up _11

02 SETTING UP

INSTALLING THE WATER

DISPENSER LINE

A water dispenser with a ﬁlter is one of the helpful

features on your new refrigerator. To help promote

better health, the water ﬁlter removes unwanted

particles from your water. However, it does not

sterilize or destroy microorganisms. You may need

to purchase a water purifying system to do that.

The water line also connects to the ice maker.

For the ice maker to operate properly, water

pressure of 20~125psi (138~862 kPa) is required.

If the refrigerator is installed in an area with low

water pressure (below 20psi), you can install

a booster pump to compensate for the low

pressure.

After you have connected the water line, make

sure the water storage tank inside the refrigerator

is properly ﬁlled. To do this, press the water

dispenser lever until the water runs from the water

outlet.

• Water line installation kits are available at

extra cost from your dealer.

We recommend using a water line

installation kit that contains copper

tubing and a ¼” compression nut.

• Use the new hose-sets supplied with the

appliance only. Do not re-use an old hose set.

Keep ventilation openings, in the

appliance enclosure or in the built-in

structure, clear of obstruction. Connect

to potable water supply only.

Connecting to the water supply line

1. First, shut o the main water

supply.

2. Locate the nearest cold water drinking line and

install the pipe clamp and shut o valve.

Pipe clamp

Cold water line

Shut o valve

WARNING

3. Connect the water line installation kit to the

shut o valve.

Shut o valve

Pipe clamp

Cold water line

Water line installation kit

Connecting the water supply line to

the refrigerator.

There are several items that you need to purchase

to complete this connection.

You may ﬁnd these items sold as a kit at your local

hardware store.

Use Copper Tubing Use Plastic Tubing

• ¼” copper tubing

• ¼” compression nut (1pc)

• Ferrule (2pc)

• ¼” plastic tubing

- Molded end(Bulb)

• ¼” compression nut (1pc)

Compression

Nut (1/4”)

(Assembled)

Ferrule

(Not supplied)

Plastic Tubing

(Assembled)

Compression

Fitting

(Assembled)

Molded

end(Bulb)

Compression

nut (B) (1/4”)

(Not supplied)

or

Copper tubing

(Not supplied)

Plastic tubing (B)

(Not supplied)

Household water supply line

Refrigerator

1. Connect the household water line to the

assembled compression ﬁtting.

- If you are using copper tubing, slip the

compression nut ( B ) (not supplied) and

ferrule (not supplied) on the copper tubing (not

supplied) as shown.

- If you are using plastic tubing ( B ) , insert the

molded end (Bulb) of the plastic tubing ( B ) into

the compression ﬁtting.

DA68-02601B-14.indb 11 2018. 10. 8. 오후 5:04

12_ setting up

Do not use without the molded end (Bulb)

of the plastic tubing ( B ).

2. Tighten the compression nut ( B ) onto the

compression ﬁtting.

Do not over-tighten the compression nut ( B ).

3. Turn the water on and check for any leakage.

If you ﬁnd water drops or leakage in the

connection areas, turn o the main water

supply. Check the connections and, if

necessary, tighten.

4. Flush 1 gallon of water through the ﬁlter

before drinking or using the water from the

refrigerator. (Flush approximately 6 minutes.)

To ﬂush, press a large glass or cup against the

water dispenser lever. Fill the glass, empty it

into the kitchen sink after it is ﬁlled, and then

repeat.

5. After you turn on the refrigerator, let the ice

maker make ice for 1 to 2 days. Over that

period of time, throw out the ﬁrst 1 or 2

buckets of ice the freezer makes to ensure all

impurities have been removed from the water

line.

• Only connect the water line to a

drinkable water source.

• If you have to repair or disassemble the water

line, cut o 1/4” of the plastic tubing to make

sure you get a snug, leak-free connection.

• You can test the water line quickly using

a paper cup. Under normal conditions,

the water dispenser can ﬁll a 5.75 oz.

(170 cc) cup in about 10 seconds.

CAUTION

COMPLETING THE SET UP

Now that you have your new refrigerator installed

in place, you are ready to set up and enjoy the

features and functions of the appliance.

By completing the following steps, your refrigerator

should be fully operational.

1. Make sure your refrigerator is in an appropriate

location with reasonable clearance between it

and the wall. Refer to installation instructions in

this manual.

2. Once the refrigerator is plugged in, make sure

the interior light comes on when you open the

doors.

3. Set the Temperature control to the coldest

temperature and wait for an hour. The freezer

will get slightly chilled and the motor will run

smoothly. Reset the refrigerator and freezer to

the temperatures you want.

4. After you plug the refrigerator in, it will

take a few hours to reach the appropriate

temperature. You can store food and drinks

in the refrigerator after the temperature is

suciently cool.

• Under normal conditions a 170 cc(5.75

oz) cup can be ﬁlled in about 10

seconds.

DA68-02601B-14.indb 12 2018. 10. 8. 오후 5:04

operating _13

02 OPERATING

Operating your French Door

Refrigerator

( 1 ) Ice O

Button

Press the Ice o button is you want to

turn the ice-maker o.

( 2 ) Power

Freeze

Button

Speeds up the time needed to

freeze products in the Freezer. It

can be helpful if you need to quickly

freeze easily spoiled items or if the

temperature in the Freezer has

warmed dramatically (for example, if

the door was left open).

( 3 )

Freezer

Button

Press the Freezer button to set the

Freezer to your desired temperature.

You can set the temperature between

5°F (-15°C) and -8°F(-23°C) .

( 4 ) Fridge

Button

Press the Fridge button to set the

fridge to your desired temperature.

You can set temperature between

34°F(1°C) and 44°F(7°C) .

( 5 ) Power

Cool

Button

Speeds up the time needed to cool

products in the Refrigerator. It can

be helpful if you need to quickly

cool easily spoiled items or if the

temperature in the fridge has warmed

dramatically (For example, if the door

was left open).

( 6 ) E.

Saver

Button

For better energy eciency,

press E.Saver button. However, if

condensation occurs on the door, turn

the E.Saver function o.

Press this button for 3 seconds to

switch the temperature units between

°C and °F.

( 7 ) Filter

Indicator

When the ﬁlter indicator light is on, it is

time to change the ﬁlter. Typically this

happens about every 6 months.

The ﬁlter Indicator will be Red when

you have used your water ﬁlter for

6months.

The icon will blink red for several

seconds when you open or close the

door.

The ﬁlter indicator will be O when you

insert the new water ﬁlter.

COOLING OFF MODE

(“OF & OF” CODE ON THE DISPLAY)

• This function is for store display

refrigerators. It is not for customer use.

In Cooling O Mode, the refrigerator

works but doesn’t make cool air.

To cancel this mode, press the Power

Freeze and Freezer buttons at the same

time for 5seconds until a “Ding-dong”

sound is heard and the unit will now cool.

CAUTION

USING THE CONTROL PANEL

v





G

{









G

w







G

~









1 2 3 4 5 67

DA68-02601B-14.indb 13 2018. 10. 8. 오후 5:04

14_ operating

CHANGING THE WATER FILTER

To reduce risk of water damage to your

property DO NOT use generic brands

of water ﬁlters in your SAMSUNG

Refrigerator.

USE ONLY SAMSUNG BRAND WATER FILTERS.

SAMSUNG will not be legally responsible for any

damage, including, but not limited to property

damage caused by water leakage from the use of

a generic water ﬁlter. SAMSUNG Refrigerators are

designed to work ONLY WITH SAMSUNG Water

Filter.

The Filter light turns red to let you

know when it is time to change

your water ﬁlter cartridge.

To give you time to get a new ﬁlter,

the red light comes on just before

the capacity of the current ﬁlter

runs out.

(Red)

Changing the ﬁlter on time provides you with the

freshest, cleanest water from your refrigerator.

1. Shut o the water supply. Then, turn the water

ﬁlter ( 1 ) about 1/4 turn, counter-clockwise.

2. Pull the water ﬁlter ( 1 ) from the case ﬁlter ( 2 ).

2

1

• To change the water ﬁlter more easily,

shut o the water supply valve.

• Sometimes, it is hard to disassemble the water

ﬁlter because impurities in the water cause it

to stick. If you are having diculties, grip the

water ﬁlter ﬁrmly and pull it hard.

• When you pull the

water ﬁlter, a little

water can leak from

the opening. This is

normal.

3

2

To minimize the water leaks, keep the ﬁlter

cartridge horizontal when you pull it.

• To prevent overﬂow, empty the water ﬁlter tray

( 3 ) and dry around the ﬁlter case ( 2 ).

3. Insert the new ﬁlter into the ﬁlter case ( 4 ).

4. Push the ﬁlter, and then turn it clockwise until

it locks.

• If you have trouble inserting the water

ﬁlter because of high water pressure,

shut o the water supply valve.

• The locked symbol should be lined up with the

indicator line.

WARNING

4

5. After removing the

old water ﬁlter and

installing a new reset

the indicator by

pressing the “Fridge”

and “Power Cool”

button simultaneously

for about 3 seconds.

6. If you turned o the water supply, turn it back on.

• For a replacement water ﬁlter, you can

visit your local home Improvement

center or contact the Samsung Parts

distributor.

• Be sure the replacement water ﬁlter has the

SAMSUNG logo on the box and on the water

ﬁlter. Link : http://www. samsungparts.com

Removing any residual matter inside

the water supply line after installing

the water ﬁlter.

1. Turn ON the main

water supply and

supply water to the

refrigerator.

2. Run 1 Gal of water through the dispenser until

the water runs clear (approx. 6 to 7 minutes).

This will clean the water supply system and

remove air from the lines.

3. If after pour 1 Gal the water doesn’t turn

clear is possible an additional ﬂushing in the

household lines.

4. Open the Refrigerator door and make sure

there are no water leaks coming from the

water ﬁlter.

• Be sure to ﬂush the dispenser system

thoroughly, otherwise water may drip

from the dispenser.

• This means that there is still air in the line.

DA68-02601B-14.indb 14 2018. 10. 8. 오후 5:04

operating _15

02 OPERATING

Reverse Osmosis Water Supply

IMPORTANT :

The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet

valve of the refrigerator needs to be between 35

and 120 psi (241 and 827 kPa).

If a reverse osmosis water ﬁltration system is

connected to your cold water supply, the water

pressure to the reverse osmosis system needs to

be a minimum of 40 to 60 psi (276 to 414 kPa.) If

the water pressure to the reverse osmosis system

is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment ﬁlter in the

reverse osmosis system is blocked. Replace

the ﬁlter if necessary.

• Allow the storage tank on the reverse osmosis

system to reﬁll after heavy usage.

• If your refrigerator has a water ﬁlter, it may

further reduce the water pressure when used

in conjunction with a reverse osmosis system.

Remove the water ﬁlter.

If you have questions about your water pressure,

call a licensed, qualiﬁed plumber.

CONTROLLING THE TEMPERATURE

Basic temperature of Freezer and

Refrigerator Compartments

The basic temperature and recommended

temperatures of the Freezer and Refrigerator

Compartments are 0°F and 37°F(or -18°C and

3°C) respectively. If the temperature of the Freezer

and Refrigerator Compartments are too high or

low, adjust the temperature manually.

CONTROLLING THE

TEMPERATURE

Controlling the Freezer temperature

The Freezer temperature can be set between

5°F(-15°C) and -8°F(-23°C) to suit your

particular needs. Press the Freezer button

repeatedly until the desired temperature is shown

in the temperature display. Keep in mind that

foods like ice cream may melt at 4°F(-15°C).

The temperature display will move sequentially

from -8°F(-23°C) to 5°F(-15°C). When the display

reaches 5°F, it will begin again at -8°F(-23°C).

Five seconds after the new temperature is set, the

display will again show the actual current freezer

temperature until the new temperature is reached.

Controlling the Refrigerator

temperature

The Refrigerator temperature can be set between

44°F(7°C) and 34°F(1°C) to suit your particular

needs. Press the Fridge button repeatedly until the

desired temperature is shown in the temperature

display.

The temperature control process for the Fridge

works just like the Freezer process.

Press the Fridge button to set your desired

temperature. After a few seconds, the Fridge

will begin adjusting towards the newly set

temperature. This will be reﬂ ected in the digital

display.

• The temperature of the Freezer or the

Refrigerator may rise from opening

the doors too frequently, or if a large

amount

of warm or hot food is placed in

either side.

• This may cause the digital display to blink.

Once the Freezer and Refrigerator temperature

return to their normal set temperatures, the

blinking will stop.

• If the blinking continues, you may need to

“reset” the Refrigerator. Try unplugging the

appliance, wait for around 10 minutes and then

plug the power cord back in.

DA68-02601B-14.indb 15 2018. 10. 8. 오후 5:04

16_ operating

USING THE COLD WATER

DISPENSER

Using the Water dispenser

(RF261B, RF26H)

Place a glass underneath

the water outlet and push

gently against the water

dispenser lever with your

glass. Make sure the

glass is in line with the

dispenser to prevent the

water from splashing out.

PUSH

If you have just installed the refrigerator or installed

a new water ﬁ ter, Flush 3 gallons through ﬁlter

before use (ﬂush approximately 6 minutes).

Make sure water ﬂows cleanly before drinking.

If you have a long vacation or business

trip, close the water valve and shut o

the water supply to the Refrigerator.

This will help prevent accidental leakages.

• Water clouding phenomenon

• All water provided to refrigerators ﬂows

through the core ﬁlter which is an

alkaline water ﬁlter. In this process, the

pressure in the water that has ﬂowed

out of the ﬁlter gets increased, and

oxygen and nitrogen become saturated.

When this water ﬂows out in the air, the

pressure plummets and the oxygen and

nitrogen get supersaturated so that they

turn into gas bubbles. The water could

look misty due to these oxygen bubbles.

The water may look temporarily cloudy

due to these oxygen bubbles. After a

few seconds, the water will look clear.

• The water tank’s capacity is

approximately one third (1/3) of a gallon.

Please wait 1 second before removing

the cup after dispensing water to

prevent spills.

CAUTION

DA68-02601B-14.indb 16 2018. 10. 8. 오후 5:04

operating _17

02 OPERATING

PARTS AND FEATURES

Use this page to become more familiar with the parts and features of the refrigerator

v





G

{







G

w







G

~









Slide-Shelf

Light

Vertical Hinged

Section

Internal Water

Dispenser(RF261B)

Vegetable &

Fruit Drawers

FZ Ice-Maker

Light

Ice Bucket

Test button

Ice Maker in Freezer

Auto Door

Closer

Quick-Space

Glass Shelf

(on some models)

Door Bins

Cool Select

Pantry

Auto Pull Out

Drawer

Freezer

Drawer Bin

Digital Sensor Control

• When closing the door, make sure the Vertical Hinged Section is in the correct position to

avoid scratching the other door.

• If the Vertical Hinged Section is reversed, put it back to the right position and close the door.

• Moisture may appear at times on the Vertical Hinged Section.

• The door handle may become loose over time. If this happens, tighten the bolts found on the

inside of the door.

• If you close one door with a lot of force, the other door may open.

• When the door opens, the interlock switch automatically turns o the auger motor in the ice

maker for safety reasons.

• When the interior or exterior LED lamp has gone out, please contact your service agents.

DA68-02601B-14.indb 17 2018. 10. 8. 오후 5:04

18_ operating

USING THE COOL SELECT

PANTRY

The Cool Select Pantry is a full-width drawer with

adjustable temperature control. This pantry can

be used for large party trays, deli items, pizza,

beverages or miscellaneous items.

There is a temperature control which can adjust

the amount of cold air allowed into the pantry.

The control is located on the right side of the

pantry.

• The Pantry has three modes: The Fresh mode,

Chilled mode, and Deli mode. Fresh mode is

the default. Press the Temp button repeatedly

until the mode you want is lit. Once you select

a mode, the temperature will change to match

the mode you selected.

• The Pantry temperature may change

depending on the number of items inside

and where they are located, the ambient

temperature, and how often the door is

opened.

The Pantry Selection Button

1. When you select “Deli”, the temperature of the

pantry will be kept around 41 °F (or 5 °C). This

feature helps keep food fresh for a long time.

2. When you select

“Fresh”, the

temperature of

the pantry will be

kept around 38 °F

(or 3 °C).

This feature helps

keep food fresh

for a longer time.

3. When you select “Chilled”, the temperature of

the pantry will be kept around 34 °F (or 1 °C).

This feature also helps keep meat or ﬁsh fresh

for a longer time.

The table below lists the Pantry modes and

the kinds of foods that can be stored safely for

each mode.

Deli Fresh Chiled

• Pineapples • cucumbers • steaks

• lemons • apples • hard cheeses

• avocado • oranges • cold cuts

• potato • grapes • bacon

• zucchinis • hot dogs

• corn

• Fruits and vegetables may be damaged

when the “Chilled” mode is set.

• Do not store lettuce or other leafy

produce in this pantry.

Do not store glass bottles in this pantry.

If they are frozen, they can break and

cause personal injury.

In case you put a water bowl without its

ild into the pantry, condensation may

form around surrounding parts.

REMOVING THE REFRIGERATOR

ACCESSORIES

1. Door Bins & Dairy Compartment

• Door Bins

To remove - Simply lift the bin up and pull straight

out.

To relocate - Slide it in above the desires location

and push down until it stops.

v

G

{







G

w







G

~







CAUTION

DA68-02601B-14.indb 18 2018. 10. 8. 오후 5:04

operating _19

02 OPERATING

• Injury may occur if the door bins are not

ﬁrmly assembled.

• Do not allow children to play with the bins.

Sharp corners of the bins may cause injury.

Do not adjust a bin full of food. Remove

the food ﬁrst.

To remove dust from the bins - Remove

the guard and wash in water.

2. Tempered Glass shelves

To remove - Tilt up the front of the shelf in the

direction shown ( 1 ) and lift it up vertically ( 2 ).

Pull the shelf out.

To relocate - Tilt the front of the shelf up and

guide the shelf hooks into the slots at a desired

height. Then lower the front of the shelf so that the

hooks can drop into the slots.

The Tempered Glass shelves are heavy.

Use special care when removing them.

1

2

3. Vegetable & Fruit Drawers

To remove - Pull the drawer out to full extension.

Tilt up the front of the drawer and pull straight out.

To relocate - Insert the drawer into the frame rails

and push back into place.

The drawers need to be removed before

the glass shelf above them can be lifted

out.

4. Cool select pantry

To remove the Cool select pantry - Pull the

pantry out to full extension. Tilt up the front side of

the pantry and pull straight out.

CAUTION

To relocate the Cool select pantry – Push

the rails to the back of the refrigerator. Place the

drawer onto the rails and slide the pantry back

until it is in place.

To remove the divider – Pull the pantry

completely out to full extension and raise the front

side of the divider to unhook it from the rear wall

of the pantry, then lift the divider out.

To relocate the divider - Hook the back of the

divider over the rear wall of the pantry and push

the divider down.

Using the doors

Ensure that the doors close all the way and are

securely sealed.

When the refrigerator door is only partially open,

it will automatically close. But, the door will stay

open when opened more than the auto close

range and you must close it manually.

REMOVING THE REFRIGERATOR

ACCESSORIES

1.

ICE BUCKET

To remove - Lift the ice bucket ( 1 ).

To relocate - Place the ice bucket into the Super

extended drawer ( 2 ).

1

2

DA68-02601B-14.indb 19 2018. 10. 8. 오후 5:04

20_ operating

2. Super Extended Drawer

To remove - Pull the drawer out to full extension.

Tilt up the rear of the drawer and lift straight out.

To relocate - Place the drawer onto the rails ( 4 )

by tilting it up. Lower the drawer into place until it

is horizontal and slide the Drawer ( 3 ) in.

3

4

3. Freezer Drawer

To remove the freezer drawer - Pull the freezer

drawer out fully. Tilt up the rear of the bin and lift it

out to remove.

To relocate the freezer drawer - Place the bin

into the rail assembly.

Do not allow babies or children go inside

the freezer drawer. They could damage

the refrigerator and seriously injure

themselves.

Do not sit on the freezer door. The door

may break. Do not allow children to

climb into the freezer drawer.

Do not remove the divider.

If trapped inside, children may be injured

or suocate to death.

CAUTION

WARNING

CLEANING THE

REFRIGERATOR

Caring for your Samsung French Door Refrigerator

prolongs the life of your appliance and helps keep

the refrigerator free of odor and germs.

Cleaning the Interior

Clean the inside walls and accessories with a mild

detergent and then wipe dry with a soft cloth. You

can remove the drawers and shelves for a more

thorough cleaning. Just make sure to dry drawers

and shelves before putting them back into place.

Cleaning the Exterior

Wipe the control panel and digital display with

a damp, clean, soft cloth. Do not spray water

directly on the surface of the refrigerator.

The doors, handles, and cabinet surfaces should

be cleaned with a mild detergent and then wiped

dry with a soft cloth. To keep your appliance

looking its best, polish the exterior once or twice a

year.

Do not spray water directly on the

refrigerator. Use a clean, damp cloth to

clean.

Do not use benzene, thinner, or Clorox

for cleaning. They may damage the

surface of the appliance and may cause

a ﬁre.

You can erase the printed

letters on the display if you

apply stainless cleaner

directly to the area where

the letters are printed.

CAUTION

DA68-02601B-14.indb 20 2018. 10. 8. 오후 5:04

La page charge ...

Samsung RF26HFPNBSR Manuel utilisateur

Samsung RF26HFPNBSR Manuel utilisateur

dans d''autres langues

Documents connexes