Hilti SC 60W-A36 Mode d'emploi

SC 60W-A36

English 1

Français 18

Español 37

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

1

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

2

3

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

4

5

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

6

7

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

8

9

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

SC 60W-A36

en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 1

fr Notice d'utilisation originale . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

es Manual de instrucciones original . . . . . . . . . . . . . . . . . . . . . . . 37

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

*2172267*

2172267 English 1

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a

prerequisite for safe, trouble-free handling and use of the product.

• Observe the safety instructions and warnings in this documentation and

on the product.

• Always keep the operating instructions with the product and make sure

that the operating instructions are with the product when it is given to

other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the

product. The following signal words are used:

DANGER

DANGER !

▶ Draws attention to imminent danger that will lead to serious personal

injury or fatality.

WARNING

WARNING !

▶ Draws attention to a potential threat of danger that can lead to serious

injury or fatality.

CAUTION

CAUTION !

▶ Draws attention to a potentially dangerous situation that could lead to

slight personal injury or damage to the equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household

waste

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

2 English 2172267

*2172267*

These numbers refer to the corresponding illustrations found at the

beginning of these operating instructions

The numbering reflects the sequence of operations shown in the

illustrations and may deviate from the steps described in the text

Item reference numbers are used in the overview illustrations and

refer to the numbers used in the product overview section

This symbol is intended to draw special attention to certain points

when handling the product.

Wireless data transfer

1.3 Product information

products are designed for professional users and only trained,

authorized personnel are permitted to operate, service and maintain the

products. This personnel must be specifically informed about the possible

hazards. The product and its ancillary equipment can present hazards if

used incorrectly by untrained personnel or if used not in accordance with

the intended use.

The type designation and serial number are printed on the rating plate.

▶ Write down the serial number in the table below. You will be required to

state the product details when contacting Hilti Service or your local Hilti

organization to inquire about the product.

Product information

Circular saw SC 60WA36

Generation 01

Serial no.

1.4 Declaration of conformity

We declare, on our sole responsibility, that the product described here

complies with the applicable directives and standards. A copy of the

declaration issued by the certification department can be found at the end

of this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916

Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and

specifications provided with this power tool. Failure to follow all instruc-

tions listed below may result in electric shock, fire and/or serious injury.

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

*2172267*

2172267 English 3

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

Work area safety

▶ Keep work area clean and well lit. Cluttered or dark areas invite

accidents.

▶ Do not operate power tools in explosive atmospheres, such as in

the presence of flammable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

▶ Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

Electrical safety

▶ Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will reduce risk of electric

shock.

▶

Avoid body contact with earthed or grounded surfaces, such as

pipes, radiators, ranges and refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

▶ Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

▶ Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

▶ When operating a power tool outdoors, use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use reduces the risk

of electric shock.

▶ If operating a power tool in a damp location is unavoidable, use

a residual current device (RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

Personal safety

▶ Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired

or under the influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in serious personal

injury.

▶ Use personal protective equipment. Always wear eye protection.

Protective equipment such as a dust mask, non-skid safety shoes, hard

hat or hearing protection used for appropriate conditions will reduce

personal injuries.

▶ Prevent unintentional starting. Ensure the switch is in the off-position

before connecting to power source and/or battery pack, picking up

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

4 English 2172267

*2172267*

or carrying the tool. Carrying power tools with your finger on the switch

or energising power tools that have the switch on invites accidents.

▶ Remove any adjusting key or wrench before turning the power tool

on. A wrench or a key left attached to a rotating part of the power tool

may result in personal injury.

▶ Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

▶ Dress properly. Do not wear loose clothing or jewellery. Keep your

hair and clothing away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

▶ If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

Use of dust collection can reduce dust-related hazards.

▶ Do not let familiarity gained from frequent use of tools allow you

to become complacent and ignore tool safety principles. A careless

action can cause severe injury within a fraction of a second.

Power tool use and care

▶ Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate for which it was designed.

▶ Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous

and must be repaired.

▶ Disconnect the plug from the power source and/or remove the

battery pack, if detachable, from the power tool before making

any adjustments, changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the power tool

accidentally.

▶ Store idle power tools out of the reach of children and do not

allow persons unfamiliar with the power tool or these instructions

to operate the power tool. Power tools are dangerous in the hands of

untrained users.

▶ Maintain power tools and accessories. Check for misalignment or

binding of moving parts, breakage of parts and any other condition

that may affect the power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents are caused by poorly

maintained power tools.

▶ Keep cutting tools sharp and clean. Properly maintained cutting tools

with sharp cutting edges are less likely to bind and are easier to control.

▶ Use the power tool, accessories and tool bits etc. in accordance with

these instructions, taking into account the working conditions and

the work to be performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

*2172267*

2172267 English 5

▶ Keep handles and grasping surfaces dry, clean and free from oil and

grease. Slippery handles and grasping surfaces do not allow for safe

handling and control of the tool in unexpected situations.

Battery tool use and care

▶ Recharge only with the charger specified by the manufacturer. A

charger that is suitable for one type of battery pack may create a risk of

fire when used with another battery pack.

▶ Use power tools only with specifically designated battery packs. Use

of any other battery packs may create a risk of injury and fire.

▶ When battery pack is not in use, keep it away from other metal

objects, like paper clips, coins, keys, nails, screws or other small

metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a

fire.

▶ Under abusive conditions, liquid may be ejected from the battery;

avoid contact. If contact accidentally occurs, flush with water. If

liquid contacts eyes, additionally seek medical help. Liquid ejected

from the battery may cause irritation or burns.

▶ Do not use a battery pack or tool that is damaged or modified.

Damaged or modified batteries may exhibit unpredictable behaviour

resulting in fire, explosion or risk of injury.

▶ Do not expose a battery pack or tool to fire or excessive temperature.

Exposure to fire or temperature above 265 °F may cause explosion.

▶ Follow all charging instructions and do not charge the battery pack

or tool outside the temperature range specified in the instructions.

Charging improperly or at temperatures outside the specified range may

damage the battery and increase the risk of fire.

Service

▶ Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power

tool is maintained.

▶ Never service damaged battery packs. Service of battery packs should

only be performed by the manufacturer or authorized service providers.

2.2 Safety instructions for all saws

Cutting procedures

▶ DANGER: Keep hands away from cutting area and the blade. Keep

your second hand on auxiliary handle or motor housing. If both hands

are holding the saw, they cannot be cut by the blade.

▶ Do not reach underneath the workpiece. The guard cannot protect you

from the blade below the workpiece.

▶ Adjust the cutting depth to the thickness of the workpiece. Less than

a full tooth of the blade teeth should be visible below the workpiece.

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

6 English 2172267

*2172267*

▶ Never hold the workpiece in your hands or across your leg while

cutting. Secure the workpiece to a stable platform. It is important to

support the work properly to minimise body exposure, blade binding, or

loss of control.

▶ Hold the power tool by insulated gripping surfaces, when performing

an operation where the cutting tool may contact hidden wiring.

Contact with a "live" wire will also make exposed metal parts of the power

tool "live" and could give the operator an electric shock.

▶ When ripping, always use a rip fence or straight edge guide. This

improves the accuracy of cut and reduces the chance of blade binding.

▶

Always use blades with correct size and shape (diamond versus

round) of arbour holes. Blades that do not match the mounting hardware

of the saw will run off-centre, causing loss of control.

▶ Never use damaged or incorrect blade washers or bolt. The blade

washers and bolt were specially designed for your saw, for optimum

performance and safety of operation.

Kickback causes and related warnings

• kickback is a sudden reaction to a pinched, jammed or misaligned saw

blade, causing an uncontrolled saw to lift up and out of the workpiece

toward the operator;

• when the blade is pinched or jammed tightly by the kerf closing down, the

blade stalls and the motor reaction drives the unit rapidly back toward the

operator;

• if the blade becomes twisted or misaligned in the cut, the teeth at the

back edge of the blade can dig into the top surface of the wood causing

the blade to climb out of the kerf and jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect operating procedures or

conditions and can be avoided by taking proper precautions as given below.

▶ Maintain a firm grip with both hands on the saw and position your

arms to resist kickback forces. Position your body to either side of

the blade, but not in line with the blade. Kickback could cause the

saw to jump backwards, but kickback forces can be controlled by the

operator, if proper precautions are taken.

▶ When blade is binding, or when interrupting a cut for any reason,

release the trigger and hold the saw motionless in the material until

the blade comes to a complete stop. Never attempt to remove the

saw from the work or pull the saw backward while the blade is in

motion or kickback may occur. Investigate and take corrective actions

to eliminate the cause of blade binding.

▶ When restarting a saw in the workpiece, centre the saw blade in the

kerf so that the saw teeth are not engaged into the material. If a saw

blade binds, it may walk up or kickback from the workpiece as the saw is

restarted.

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

*2172267*

2172267 English 7

▶ Support large panels to minimise the risk of blade pinching and

kickback. Large panels tend to sag under their own weight. Supports

must be placed under the panel on both sides, near the line of cut and

near the edge of the panel.

▶ Do not use dull or damaged blades. Unsharpened or improperly set

blades produce narrow kerf causing excessive friction, blade binding and

kickback.

▶ Blade depth and bevel adjusting locking levers must be tight and

secure before making the cut. If blade adjustment shifts while cutting,

it may cause binding and kickback.

▶ Use extra caution when sawing into existing walls or other blind

areas. The protruding blade may cut objects that can cause kickback.

Lower guard function

▶ Check the lower guard for proper closing before each use. Do not

operate the saw if the lower guard does not move freely and close

instantly. Never clamp or tie the lower guard into the open position.

If the saw is accidentally dropped, the lower guard may be bent. Raise

the lower guard with the retracting handle and make sure it moves freely

and does not touch the blade or any other part, in all angles and depths

of cut.

▶ Check the operation of the guard return spring. If the guard and

the spring are not operating properly, they must be serviced before

use. Lower guard may operate sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

▶ The lower guard may be retracted manually only for special cuts such

as "plunge cuts" and "compound cuts". Raise the lower guard by the

retracting handle and as soon as the blade enters the material, the

lower guard must be released. For all other sawing, the lower guard

should operate automatically.

▶ Always observe that the lower guard is covering the blade before

placing the saw down on bench or floor. An unprotected, coasting

blade will cause the saw to walk backwards, cutting whatever is in its

path. Be aware of the time it takes for the blade to stop after switch is

released.

2.3 Additional safety instructions

Personal safety

▶ Do not tamper with or attempt to make alterations to the power tool.

▶ Wear ear protectors. Exposure to noise can cause hearing loss.

▶ Operate the power tool only together with the safety devices that belong

to it.

▶ Take breaks between working and do relaxation and finger exercises to

improve the blood circulation in your fingers.

▶ Switch the power tool on only after it is in position at the workpiece.

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

8 English 2172267

*2172267*

▶ When working with the power tool, always guide it away from your body.

▶ Never work overhead with the product.

▶ Do not attempt to brake the product by applying lateral pressure to the

saw blade.

▶ Do not touch the clamping flange or the clamping screw while the power

tool is running.

▶ The line of cut must be free of obstructions. Do not saw into screws, nails

etc.

▶ Never press the drive spindle lock button while the saw blade is rotating.

▶ The power tool is not intended for use by debilitated persons who have

received no special training. Keep the power tool out of reach of children.

▶ Do not point the power tool toward persons.

▶ Adapt the forward pressure applied to the saw blade and the material

being cut so that the blade does not stall. A stalled saw blade can cause

kickback.

▶ Avoid overheating the tips of the saw blade teeth.

▶ When cutting plastic, avoid melting the plastic.

▶ Dust from materials such as lead-based paint, certain types of wood and

concrete, masonry and stone containing quartz, minerals and metal can

be harmful to health. Contact with or inhalation of the dust can cause

allergic reactions and/or respiratory or other diseases among operators or

bystanders. Certain kinds of dust such as oakwood and beechwood dust

are classified as carcinogenic, especially in conjunction with additives

for wood conditioning (chromate, wood preservative). Only specialists

are permitted to handle material containing asbestos. If necessary, wear

a respirator appropriate for the type of dust generated. Ensure that

the workplace is well ventilated. Comply with national regulations

applicable to the materials you will be working with.

▶ Always engage the transport safety lock before storing or transporting the

saw.

▶ Never carry the power tool with your finger on the on/off switch.

▶ Remove the battery from the power tool before breaks, before mainte-

nance, before changing accessory tools and before transportation.

▶ Flying fragments can injure the body and eyes. Wear your personal

protective equipment and always wear protective glasses and protective

gloves.

▶ Use light respiratory protection when using the power tool without a dust

removal system for work that creates dust.

▶ Always set the cutting depth to approx. 2 mm (0.08 inch) more than the

thickness of the material to be cut.

▶ When working with the power tool, hold it securely with both hands.

Electrical safety

▶ Before beginning work, check the working area (e.g. using a metal

detector) to ensure that no concealed electric cables or gas and

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

*2172267*

2172267 English 9

water pipes are present. External metal parts on the power tool can

become live, for example if you inadvertently damage electric wiring. This

presents a serious risk of electric shock.

2.4 Battery use and care

▶ Observe the special regulations and instructions applicable to the trans-

port, storage and use of Li-ion batteries.

▶ Do not expose batteries to high temperatures, direct sunlight or fire.

▶ Do not disassemble, crush or incinerate batteries and do not subject them

to temperatures over 80 °C.

▶ Do not use or charge batteries that have suffered mechanical impact,

have been dropped from a height or show signs of damage. In this case,

always contact your Hilti Service.

▶ If the battery is too hot to touch it may be defective. In this case, place the

product in a non-flammable location, well away from flammable materials,

where it can be kept under observation and allowed to cool down. In this

case, always contact your Hilti Service.

3 Description

3.1 Product overview 1

@

Auxiliary grip

;

Cutting depth scale

=

Transport safety lock

%

On/off switch

&

Battery compartment release

button

(

Hex key

)

Clamping lever for cutting

depth adjustment

+

Pivoting guard operating lever

§

Pivoting guard

/

Arbor

:

Base plate

∙

0° cutting line indicator

$

45° cutting line indicator

£

Work-area light

|

Direction-of-rotation arrow

¡

Mounting flange

Q

Clamping flange

W

Clamping screw

E

Grip

R

Charge-status and fault indi-

cator

T

Release buttons (also used

to activate the charge status

indicator)

Z

Battery

U

Spindle lock button

I

Cutting angle scale

O

Clamping lever for cutting

angle adjustment

3.2 Intended use

The product described is a cordless circular saw. It is designed for sawing

wood or wood-like materials, plastics, drywall panel and gypsum fiber board.

▶ Use only Hilti Li-ion batteries from the B 36 series with this product.

▶ Use only Hilti battery chargers from the C4/36 series for these batteries.

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

10 English 2172267

*2172267*

3.3 Possible misuse

Do not use the saw to cut materials containing quartz.

Use of saw blades not in compliance with the given specification (e.g.

diameter, speed of rotation, thickness) or use of cutting and grinding discs

or blades made from high-alloy steel (HSS steel) is not permissible.

3.4 Transport safety lock

The power tool is equipped with a transport safety lock designed to avoid

unintentional starting.

Disengage the transport safety lock before use of the power tool and re-

engage it after use.

• To engage the transport safety lock, slide the transport safety lock to the

rear until it engages .

• To disengage the transport safety lock, slide the transport safety lock

forward until it disengages .

3.5 Items supplied

Circular saw, hex key, operating instructions.

Other system products approved for use with this product can be

found at your local Hilti Store or online at: www.hilti.group | USA:

www.hilti.com

3.6 Liion battery display

The state of charge of the Li-ion battery and malfunctions of the power tool

are indicated by the display on the Liion battery. The state of charge of

the Liion battery is displayed after pressing one of the two battery release

buttons.

Status Meaning

4 battery LEDs light up. • State of charge: 75 % to 100 %

3 battery LEDs light up. • State of charge: 50 % to 75 %

2 battery LEDs light up. • State of charge: 25 % to 50 %

1 battery LED lights up. • State of charge: 10 % to 25 %

1 battery LED flashes, the power

tool is in working order.

• State of charge: < 10 %

Battery state of charge cannot be displayed while the on/off switch is

pressed and for up to 5 seconds after releasing the on/off switch.

If the battery display LEDs blink, please observe the instructions given

in the Troubleshooting section.

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

*2172267*

2172267 English 11

4 Technical data

SC 60WA36

Rated voltage

36 V

Weight with battery (9.0 Ah)

5.84 kg (12.9 lb)

Saw blade disc thickness

0.02 in … 0.06 in

(0.5 mm …

1.5 mm)

Saw blade arbor size

0.6 in

(16 mm)

Cutting depth at 0°

0 in … 2.37 in

(0 mm … 60.3 mm)

Cutting depth at 45°

0 in … 1.94 in

(0 mm … 49.2 mm)

Cutting depth at 53°

0 in … 1.69 in

(0 mm … 42.8 mm)

No-load speed

4,000 /min

5 Preparations at the workplace

CAUTION

Risk of injury by inadvertent starting!

▶ Before inserting the battery, make sure that the product is switched off.

▶ Remove the battery before making any adjustments to the power tool or

before changing accessories.

Observe the safety instructions and warnings in this documentation and on

the product.

5.1 Removing the battery 2

1. Press the battery compartment release button.

◁ The battery compartment cover opens.

2. Press both release buttons on the battery simultaneously and pull the

battery out of the tool.

3. Remove the battery.

4. Push the battery compartment cover into the closed position until it is

heard to engage with a click.

5.2 Removing the saw blade 3

WARNING

Risk of burning injury. A hot accessory tool, clamping flange or clamping

screw and the sharp edges of the saw blade present hazards.

▶ Wear protective gloves when changing saw blades.

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

12 English 2172267

*2172267*

1. Remove the battery. → page 11

2. Insert the hex key into the saw blade clamping screw.

3. Press and hold down the spindle lock button.

4. Turn the saw blade clamping screw with the hex key until the spindle lock

button engages fully.

5. Release the clamping screw by turning the hex key in the direction of the

direction-of-rotation arrow.

6. Remove the clamping screw from the outer clamping flange.

7. Open the pivoting guard by swinging it to the side and then remove the

saw blade.

8. Fit the outer flange by turning it in the direction opposite to that of the

direction-of-rotation arrow.

5.3 Installing the saw blade 4

Use only saw blades of a diameter corresponding to the markings on

the saw.

1. Remove the battery. → page 11

2. Clean the mounting flange and the clamping flange.

3. Slip the mounting flange right way round on to the arbor.

4. Open the pivoting guard.

5. Insert the new saw blade.

Note the direction-of-rotation arrows on the saw blade and on the

product. They must point in the same direction.

6. Install the outer clamping flange the right way round.

7. Insert the clamping screw.

8. Insert the hex key into the saw blade clamping screw.

9. Press the spindle lock button.

10.Secure the clamping flange with the clamping screw by turning the hex

key in the direction opposite to the direction-of-rotation arrow.

◁ The spindle lock button engages.

11.Before using the power tool, check that the saw blade is correctly seated

and tightened securely.

12.Insert the hex key into the hole provided for the purpose.

5.4 Adjusting the cutting depth 5

1. Release the cutting depth adjustment clamping lever.

2. Set the cutting depth.

◁ The cutting depth is shown on the cutting depth scale.

For a clean-edged cut, set cutting depth to the thickness of the

material plus 2 mm.

3. Secure the cutting depth adjustment clamping lever.

Printed: 04.06.2018 | Doc-Nr: PUB / 5389747 / 000 / 01

La page charge ...

Hilti SC 60W-A36 Mode d'emploi

Hilti SC 60W-A36 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents