Indesit AR7L 125 (EX) Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi
GB
1
English, 1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washing machine
and starting a wash cycle, 4-5
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 6
Table of wash cycles
Personalisation, 7
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 8
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Garments requiring special care
Load balancing system
Precautions and tips, 9
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
GB
AR7L 125
Instructions for use
WASHING MACHINE
F
Français,13
AR
, 25
2
GB
A
Installation
This instruction manual should be kept in a safe
place for future reference. If the washing machine is
sold, transferred or moved, make sure that the
instruction manual remains with the machine so that
the new owner is able to familiarise himself/herself
with its operation and features.
Read these instructions carefully: they contain vital
information relating to the safe installation and
operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not been
damaged during the transportation process. If it has
been damaged, contact the retailer and do not
proceed any further with the installation process.
3. Remove the 3
protective screws (used
during transportation) and
the rubber washer with
the corresponding
spacer, located on the
rear part of the appliance
(see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need
them again if the washing machine needs to be
moved to another location.
Packaging materials should not be used as toys for
children.
Levelling
1. Install the washing machine on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or anything else.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or loosening
the adjustable front feet
(see figure); the angle of
inclination, measured in
relation to the worktop,
must not exceed 2°.
Levelling the machine correctly will provide it with
stability, help to avoid vibrations and excessive noise
and prevent it from shifting while it is operating. If it is
placed on carpet or a rug, adjust the feet in such a
way as to allow a sufficient ventilation space
underneath the washing machine.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Insert seal A into the
end of the inlet hose and
screw the latter onto a
cold water tap with a 3/4
gas threaded opening
(see figure).
Before performing the
connection, allow the
water to run freely until it
is perfectly clear.
2. Connect the inlet hose
to the washing machine
by screwing it onto the
corresponding water inlet
of the appliance, which is
situated on the top right-
hand side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over or bent.
The water pressure at the tap must fall within the
values indicated in the Technical details table (see
next page).
If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
Never use second-hand hoses.
Use the ones supplied with the machine.
GB
3
Technical data
Model
AR7L 125
Dimensions
width 59.5 cm
height 85 cm
depth 56,5 cm
Capacity
from 1 to 7 kg
Electrical
connections
please refer to the technical data
plate fixed to the machine
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1200 rotations per minute
Energy rated
programmes
according to
regulation
EN 60456
programme 6; temperature 60°C;
using a load of 7 kg.
This appliance conforms to the
following EC Directives:
- 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent modifications
- 2006/95/EC (Low Voltage)
- 2002/96/EC
65 - 100 cm
Connecting the drain hose
Connect the drain hose,
without bending it, to a
drainage duct or a wall
drain located at a height
between 65 and 100 cm
from the floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not
be underwater.
We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
the socket is earthed and complies with all
applicable laws;
the socket is able to withstand the maximum power
load of the appliance as indicated in the Technical
data table (see opposite);
the power supply voltage falls within the values
indicated in the Technical data table (see opposite);
the socket is compatible with the plug of the
washing machine. If this is not the case, replace
the socket or the plug.
The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to rain,
storms and other weather conditions.
When the washing machine has been installed, the
electricity socket must be within easy reach.
Do not use extension cords or multiple sockets.
The cable should not be bent or compressed.
The power supply cable must only be replaced by
authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, using the wash cycle 1.
4
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see Detergents
and laundry).
There is a key which provides a summary of the
available wash cycles inside the detergent dispenser
drawer; this may be consulted at any time.
ON/OFF button: switches the washing machine on
and off.
WASH CYCLE knob: programmes the wash cycles.
During the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to
select the available functions. The indicator light
corresponding to the selected function will remain lit.
TEMPERATURE knob: sets the temperature or the
cold wash cycle (see Personalisation).
SPIN SPEED knob: sets the spin speed or exclude
the spin cycle completely (see Personalisation).
WASH CYCLE PROGRESS/DELAY TIMER
indicator light
s: used to monitor the progress of the
wash cycle.
The illuminated indicator light shows which phase is in
progress.
If the Delay Timer function has been set, the time
remaining until the wash cycle starts will be indicated
(see next page).
DOOR LOCKED indicator light: indicates whether
the door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or
temporarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash
orange, while the indicator light for the current wash
cycle phase will remain lit in a fixed manner. If the
DOOR LOCKED
indicator light is switched off, the
door may be opened.
To start the wash cycle from the point at which it was
interrupted, press this button again.
Description of the washing machine
and starting a wash cycle
TEMPERATURE
knob
Detergent dispenser drawer
WASH CYCLE PROGRESS/
DELAY TIMER
indicator lights
FUNCTION
buttons with
indicator lights
ON/OFF
button
SPIN SPEED
knob
DOOR
LOCKED
indicator light
START/PAUSE
button with indicator
light
Control panel
WASH CYCLE
knob
GB
5
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Delayed start
If the DELAY TIMER function has been activated (see
Personalisation), after the wash cycle has been
started the indicator light corresponding to the
selected delay period will begin to flash:
As time passes, the remaining delay will be displayed
and the corresponding indicator light will flash:
Once the set delay has elapsed, the flashing indicator
light will switch off and the selected wash cycle will
begin.
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has
begun, the indicator lights switch on one by one to
indicate which phase of the cycle is currently in progress.
Function buttons and corresponding indicator
lights
When a function is selected, the corresponding
indicator light will illuminate.
If the selected function is not compatible with the
programmed wash cycle, the corresponding indicator
light will flash and the function will not be activated.
If a function which is incompatible with another
function selected previously, only the most recent
selection will remain active.
Door locked indicator light
If this indicator light is on, the appliance door is locked
to prevent it from being opened accidentally; to avoid
any damage, wait for the indicator light to switch off
before you open the appliance door.
N.B. If the DELAY TIMER function is activated, the door
cannot be opened; pause the machine by pressing the
START/PAUSE button if you wish to open it.
If the START/PAUSE indicator light (orange) flashes
rapidly at the same time as the function indicator
light, this indicates a problem has occurred (see
Troubleshooting).
Starting a wash cycle
1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few
seconds, then they will switch off and the START/PAUSE indicator light will pulse.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see Personalisation).
5. Set the spin speed (see Personalisation).
6. Measure out the detergent and washing additives (see Detergents and laundry).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit
in a fixed manner, in green.
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
9. At the end of the wash cycle the
indicator light will switch on. The DOOR LOCKED indicator light will switch
off, indicating that the door may be opened. Take out your laundry and leave the appliance door ajar to make
sure the drum dries completely.
Switch the washing machine off by pressing the ON/OFF button.
Wash
Rinse
Spin
Drain no spin
End of wash cycle
6
GB
Wash cycles
The information contained in the table is intended as a guide only.
For all Test Institutes:
1) Test wash cycle in compliance with regulation EN 60456: set wash cycle 6 with a temperature of 60°C.
2) Long wash cycle for cottons: set wash cycle 1 with a temperature of 40°C.
3) Short wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.
Wash cycles
Table of wash cycles
Description of the wash cycle
Max
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max.
load
(kg)
Cycle
duration
Bleach Wash
Fabric
softener
Special cycles
6
Sanitizing cycle:
Extremely soiled whites.
90° 1200
ll l
7170
6
Sanitizing cycle (1):
Heavily soiled whites and resistant colours.
60° 1200 -
ll
7 153
7
Goodnigt cycle:
Lightly soiled delicate colours.
4 800 -
ll
4290
8
Baby cycle:
Heavily soiled delicate colours.
4 800 -
ll
2 118
9
Shirts
4 600 -
ll
270
10
Silk/Curtains:
For garments in silk and viscose, lingerie.
30° 0 -
ll
155
11
Wool:
For wool, cashmere, etc.
4 600 -
ll
1,5 55
Everyday wash cycles (Daily)
1
Cotton:
Heavily soiled whites and resistant colours.
60° 1200
ll l
7 122
1
Cotton (2):
Heavily soiled whites and delicate colours.
40° 1200
ll l
7 115
2
Coloured Cottons (3):
Lightly soiled whites and delicate colours.
40° 1200
ll l
785
3
Synthetics resistents:
Heavily soiled resistant colours.
60° 800 -
ll
385
3
Synthetics delicates:
Lightly soiled resistant colours.
4 800 -
ll
370
4
Mix 30':
To refresh lightly soiled garments quickly (not suitable
for wool, silk and clothes which require washing by hand).
30° 800 -
ll
330
5
Mix 15':
To refresh lightly soiled garments quickly (not suitable
for wool, silk and clothes which require washing by hand).
30° 800 -
ll
1,5 15
Partial wash cycles
A
Rinse - 1200 - -
l
736
B
Light rinse - 800 - -
l
331
C
Spin - 1200 - - - 716
D
Light spin - 800 - - - 312
E
Drain no spin - 0 - - - 72
Specials wash cycles
Sanitizing cycle (wash cycle 6). A high-temperature hygienic wash cycle (over 60°C) which requires the use of bleach.
Pour the bleach, the detergent and the additives into the relevant compartments (see paragraph entitled
Detergent dispenser drawer).
Goodnigt cycle (wash cycle 7). This is a silent cycle which can be run at night, when the electricity prices are lower. The
wash cycle is designed for cottons and synthetics. At the end of the cycle the machine stops while there is still water in
the drum; to spin and drain the laundry press the START/PAUSE button; alternatively the machine will perform the spin
cycle and drain the water automatically after 8 hours.
Baby cycle (wash cycle 8). This wash cycle can be used to remove the soiling typically caused by babies, while ensuring
that all detergent is removed from nappies in order to prevent the delicate skin of babies from suffering allergies. The
cycle has been designed to reduce the amount of bacteria by using a greater quantity of water and optimising the effect
of special disinfecting additives added to the detergent.
At the end of the wash cycle, the machine will slowly rotate the drum to prevent the formation of creases; to end the cycle
press the START/PAUSE button.
Mix 30 (wash cycle 4) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 30 minutes and
therefore saves both energy and time. By selecting this wash cycle (4 at 30°C), it is possible to wash different fabrics
together (except for wool and silk items), with a maximum load of 3 kg.
Mix 15(wash cycle 5) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and
therefore saves both energy and time. By selecting this wash cycle (5 at 30°C), it is possible to wash different fabrics
together (except for wool and silk items), with a maximum load of 1.5 kg.
GB
7
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash (
).
The washing machine will automatically prevent you from selecting a temperature which is higher than the
maximum value set for each wash cycle.
Setting the spin speed
Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.
The maximum spin speeds available for each wash cycle are as follows:
Wash cycles Maximum spin speed
Cottons 1200 rpm
Synthetics 800 rpm
Wool 600 rpm
Silk drain only
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol
.
The washing machine will automatically prevent you from selecting a spin speed which is higher than the
maximum speed set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in
conjunction with the selected wash cycle.
Delay timer
This timer delays the start time of the wash cycle by up to 12 hours.
Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time
the button is pressed, the function will be disabled.
N.B. Once you have pressed the START/PAUSE button, the delay time may only be decreased if you wish to modify it.
This option is enabled with all programmes.
Easy iron
By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases.
At the end of the cycle the washing machine will perform slow rotations of the drum; the EASY IRON and START/
PAUSE indicator lights will flash (orange) and the
phase will remain lit in a fixed manner. To end the cycle, press
the START/PAUSE button or the EASY IRON button.
For the Silk (10) wash cycle, the machine will end the cycle while the laundry is soaking, the EASY IRON and
START/PAUSE indicator lights will flash (orange) and the RINSE phase will remain lit in a fixed manner. To drain the
water so that the laundry may be removed, press the START/PAUSE button or the EASY IRON button.
This function may not be used in conjunction with wash cycles 4, 5, 6, 7, 8, 11, C, D, E.
Extra rinse
By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is
particularly useful for sensitive skin.
This function may not be used in conjunction with wash cycles 4, 5, C, D, E.
Super Wash
Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle
duration, this function offers a high-performance wash.
This function may not be used in conjunction with wash cycles 4, 5, 6, 10, 11, A, B, C, D, E.
Personalisation
8
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance
and contribute to environmental pollution.
Do not use hand washing detergents because these
create too much foam.
Open the detergent
dispenser drawer and
pour in the detergent or
washing additive, as
follows.
compartment 1: Pre-wash detergent (powder)
Before pouring in the detergent, make sure that extra
compartment 4 has been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 4: Bleach
Bleach cycle
Bleaching may only be performed in conjunction with
wash cycles 1, 2, 6.
Pour the bleach into extra compartment 4; pour the
detergent and softener into the corresponding
compartments, then select one of the
abovementioned wash cycles.
This option is recommended only for very soiled
cotton garments.
Preparing the laundry
Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from
whites.
Empty all garment pockets and check the buttons.
Do not exceed the listed values, which refer to the
weight of the laundry when dry:
Durable fabrics: max. 7 kg
Synthetic fabrics: max. 3 kg
Delicate fabrics: max. 2 kg
Wool: max. 1.5 kg
MAX
1
2
4
3
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Garments requiring special care
Shirts: use special wash cycle 9 to wash shirts in
various fabrics and colours.
It guarantees maximum care is taken of the garments
and minimises the formation of creases.
Silk: use special wash cycle 10 to wash all silk
garments. We recommend the use of special
detergent which has been designed to wash delicate
clothes.
Curtains: fold curtains and place them in a pillow
case or mesh bag. Use wash cycle 10.
Wool: Ariston is the only washing machine
manufacturer to have been awarded the prestigious
Woolmark Platinum Care endorsement (M.0508) by
the Woolmark Company, which means that all
woollen garments may be washed in the washing
machine, even those which state hand wash only
on the label. Wash cycle 11 therefore offers
complete peace of mind when washing woollen
garments in the washing machine (max. load 1.5 kg)
and guarantees optimal performance.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
and to distribute the load in a uniform manner, the
drum rotates continuously at a speed which is slightly
greater than the washing rotation speed. If, after
several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the
load is excessively unbalanced, the washing machine
performs the distribution process instead of spinning.
To encourage improved load distribution and balance,
we recommend small and large garments are mixed
in the load.
GB
9
Precautions and tips
This washing machine was designed and
constructed in accordance with international safety
regulations. The following information is provided for
safety reasons and must therefore be read carefully.
General safety
This appliance was designed for domestic use only.
The washing machine must only be used by adults, in
accordance with the instructions provided in this manual.
Do not touch the machine when barefoot or with
wet or damp hands or feet.
Do not pull on the power supply cable when
unplugging the appliance from the electricity
socket. Hold the plug and pull.
Do not open the detergent dispenser drawer while
the machine is in operation.
Do not touch the drained water as it may reach
extremely high temperatures.
Never force the porthole door. This could damage
the safety lock mechanism designed to prevent
accidental opening.
If the appliance breaks down, do not under any
circumstances access the internal mechanisms in
an attempt to repair it yourself.
Always keep children well away from the appliance
while it is operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group
of two or three people and handle it with the utmost
care. Never try to do this alone, because the
appliance is very heavy.
Before loading laundry into the washing machine,
make sure the drum is empty.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out "wheeled bin" symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Opening the porthole door manually
In the event that it is not possible to open the
porthole door due to a powercut, and if you wish to
remove the laundry, proceed as follows:
1. remove the plug from
the electrical socket.
2. make sure the water
level inside the machine is
lower than the door
opening; if it is not, remove
excess water using the
drain hose, collecting it in a
bucket as indicated in the
figure.
3. using a screwdriver,
remove the cover panel on
the lower front part of the
washing machine (see
figure).
4. pull outwards using the tab as indicated in the
figure, until the plastic tie-rod is freed from its stop
position; pull downwards and open the door at the
same time.
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
20
10
GB
Care and maintenance
Cutting off the water and electricity
supplies
Turn off the water tap after every wash cycle. This
will limit wear on the hydraulic system inside the
washing machine and help to prevent leaks.
Unplug the washing machine when cleaning it and
during all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth soaked
in lukewarm soapy water. Do not use solvents or
abrasives.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pulling it
out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of your
appliance
Always leave the porthole door ajar in order to
prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump which does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber which protects the
pump, situated in its bottom part.
Make sure the wash cycle has finished and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front part of
the washing machine
(see figure);
2. unscrew the lid by
rotating it anti-clockwise
(see figure): a little water
may trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are
any cracks, it should be replaced immediately: during
the wash cycles, water pressure is very strong and a
cracked hose could easily split open.
Never use second-hand hoses.
1
2
GB
11
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see Assistance),
make sure that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (the indicator light
for the first wash cycle stage
flashes rapidly).
The washing machine
continuously takes in and drains
water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
The START/PAUSE indicator light
(orange) and the function
indicator lights flash rapidly.
There is too much foam.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or is not making contact.
There is no power in the house.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set (see Personalisation).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from
the floor (see Installation).
The free end of the hose is under water (see Installation).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap,
switch the appliance off and contact the Assistance Service. If the
dwelling is on one of the upper floors of a building, there may be problems
relating to water drainage, causing the washing machine to fill with water
and drain continuously. Special anti-draining valves are available in shops
and help to avoid this inconvenience.
The wash cycle does not include draining: some wash cycles require
the drain phase to be started manually.
The EASY IRON function has been activated: To complete the wash
cycle, press the START/PAUSE button (Personalisation).
The drain hose is bent (see Installation).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see Installation).
The washing machine is not level (see Installation).
The washing machine is trapped between cabinets and walls (see Installation).
The water inlet hose is not screwed on properly (see Installation).
The detergent dispenser drawer is blocked (for cleaning instructions, see
Care and maintenance).
The drain hose is not fixed properly (see Installation).
Switch off the machine and unplug it, wait for approximately 1 minute
and then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the
text for washing machines or hand and machine wash, or the like).
Too much detergent was used.
12
GB
Service
Before calling for Assistance:
Check whether you can solve the problem alone (see Troubleshooting);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Assistance Centre using the telephone number
provided on the guarantee certificate.
Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also
be found on the front of the appliance by opening the door.
FR
13
Français
Sommaire
Installation, 14-15
Déballage et mise à niveau
Raccordements eau et électricité
Premier cycle de lavage
Caractéristiques techniques
Description du lave-linge et
démarrage dun programme, 16-17
Bandeau de commandes
Voyants
Démarrage dun programme
Programmes,18
Tableau des programmes
Personnalisations, 19
Sélection de la température
Sélection de lessorage
Fonctions
Produits lessiviels et linge, 20
Tiroir à produits lessiviels
Cycle blanchissage
Triage du linge
Linge ou vêtements particuliers
Système déquilibrage de la charge
Précautions et conseils, 21
Sécurité générale
Mise au rebut
Ouverture manuelle du hublot
Entretien et soin, 22
Coupure de larrivée deau et du courant
Nettoyage du lave-linge
Nettoyage du tiroir à produits lessiviels.
Entretien du hublot et du tambour
Nettoyage de la pompe
Contrôle du tuyau darrivée de leau
Anomalies et remèdes, 23
Assistance, 24
FR
AR7L 125
Mode demploi
LAVE-LINGE
14
FR
A
Installation
Conserver ce mode demploi pour pouvoir le
consulter à tout moment. En cas de vente, de
cession ou de déménagement, veiller à ce quil suive
toujours le lave-linge pour que son nouveau
propriétaire soit informé sur son mode de
fonctionnement et puisse profiter des conseils
correspondants.
Lire attentivement les instructions: elles fournissent
des conseils importants sur linstallation, lutilisation et
la sécurité de lappareil.
Déballage et mise à niveau
Déballage
1. Déballer le lave-linge.
2. Contrôler que le lave-linge na pas été endommagé
pendant le transport. Sil est abîmé, ne pas le
raccorder et contacter le vendeur.
3. Enlever les 3 vis de
protection servant au
transport, le caoutchouc
et la cale, placés dans la
partie arrière (voir figure).
4. Boucher les trous à laide des bouchons plastique
fournis.
5. Conserver toutes ces pièces: il faudra les remonter
en cas de transport du lave-linge.
Les pièces demballage ne sont pas des jouets pour
enfants.
Mise à niveau
1. Installer le lave-linge sur un sol plat et rigide, sans
lappuyer contre des murs, des meubles ou autre.
2. Si le sol nest pas
parfaitement horizontal,
visser ou dévisser les
pieds de réglage avant
(voir figure) pour niveler
lappareil; son angle
dinclinaison, mesuré sur
le plan de travail, ne doit
pas dépasser 2°.
Une bonne mise à niveau garantit la stabilité de
lappareil et évite quil y ait des vibrations, du bruit et
des déplacements en cours de fonctionnement. Si la
machine est posée sur de la moquette ou un tapis,
régler les pieds de manière à ce quil y ait
suffisamment despace pour assurer une bonne
ventilation.
Raccordements eau et électricité
Raccordement du tuyau darrivée de leau
1. Monter le joint A sur
lextrémité du tuyau
dalimentation et le visser
à un robinet deau froide
à embout fileté 3/4 gaz
(voir figure).
Faire couler leau jusquà
ce quelle soit limpide et
sans impuretés avant de
raccorder.
2. Raccorder le tuyau
darrivée de leau au
lave-linge en le vissant à
la prise deau prévue,
dans la partie arrière en
haut à droite (voir figure).
3. Attention à ce que le tuyau ne soit pas plié ou
écrasé.
La pression de leau doit être comprise entre les
valeurs indiquées dans le tableau des Caractéristiques
techniques (voir page ci-contre).
Si la longueur du tuyau dalimentation ne suffit pas,
sadresser à un magasin spécialisé ou à un technicien
agréé.
Nutiliser que des tuyaux neufs.
Utiliser ceux qui sont fournis avec lappareil.
FR
15
65 - 100 cm
Raccordement du tuyau de vidange
Raccorder le tuyau
dévacuation, sans le
plier, à un conduit
dévacuation ou à une
évacuation murale placés
à une distance du sol
comprise entre 65 et 100
cm;
ou bien laccrocher à un
évier ou à une baignoire,
dans ce cas, fixer le
support en plastique
fourni avec lappareil au
robinet (voir figure).
Lextrémité libre du tuyau
dévacuation ne doit pas
être plongée dans leau.
Lutilisation dun tuyau de rallonge est absolument
déconseillée mais si on ne peut faire autrement, il faut
absolument quil ait le même diamètre que le tuyau
original et sa longueur ne doit pas dépasser 150 cm.
Branchement électrique
Avant de brancher la fiche dans la prise de courant,
sassurer que:
la prise est bien reliée à la terre et est conforme aux
réglementations en vigueur;
la prise est bien apte à supporter la puissance
maximale de lappareil indiquée dans le tableau des
Caractéristiques techniques (voir ci-contre);
la tension dalimentation est bien comprise entre les
valeurs figurant dans le tableau des Caractéristiques
techniques (voir ci-contre);
la prise est bien compatible avec la fiche du lave-
linge. Autrement, remplacer la prise ou la fiche.
Le lave-linge ne doit pas être installé dehors, même
à labri, car il est très dangereux de le laisser exposé
à la pluie et aux orages.
Après installation du lave-linge, la prise de courant
doit être facilement accessible.
Nutiliser ni rallonges ni prises multiples.
Le câble ne doit être ni plié ni trop écrasé.
Le câble dalimentation ne doit être remplacé que
par des techniciens agréés.
Attention! Nous déclinons toute responsabilité en cas
de non-respect des normes énumérées ci-dessus.
Premier cycle de lavage
Avant la première mise en service de lappareil,
effectuer un cycle de lavage avec un produit lessiviel
mais sans linge et sélectionner le programme 1.
Caractéristiques techniques
Modèle
AR7L 125
Dimensions
largeur 59,5 cm
hauteur 85 cm
profondeur 56,5 cm
Capaci
de 1 à 7 kg
Raccordements
électriques
Voir la plaque signalétique appliquée
sur la machine
Raccordements
hydrauliques
pression maximale 1 MPa (10 bar)
pression minimale 0,05 MPa (0,5 bar)
capacité du tambour 52 litres
Vitesse
d'essorage
jusqu 1200 tours minute
Programmes de
contrôle selon la
norme EN 60456
programme 6; température 60°C;
effectué avec une charge de 7 kg.
Cet appareil est conforme aux
Directives Communautaires suivantes:
- 89/336/CEE du 03/05/89
(Compatibilité électromagnétique) et
modifications suivantes
- 2006/95/CE (Basse Tension)
- 2002/96/CE
16
FR
Tiroir à produits lessiviels: pour charger les
produits lessiviels et les additifs (voir Produits lessiviels
et linge).
Une légende des programmes est consultable à tout
moment à l'intérieur du tiroir.
Touche MARCHE/ARRÊT: pour allumer ou éteindre
le lave-linge.
Bouton PROGRAMMES: pour sélectionner les
programmes. Pendant le programme, le bouton ne
tournera pas.
Touches avec voyants FONCTION: pour sélectionner
les fonctions disponibles. Le voyant correspondant à
la fonction sélectionnée restera allumé.
Bouton TEMPÉRATURE: pour sélectionner la
température ou un lavage à froid (voir
Personnalisations).
Bouton ESSORAGE: pour sélectionner lessorage ou
le supprimer (voir Personnalisations).
Voyants DÉROULEMENT CYCLE/DÉPART
DIFFÉRÉ: pour suivre le stade davancement du
programme de lavage.
Le voyant allumé indique la phase de lavage en
cours.
Si la fonction Départ différé (départ différé) a été
sélectionnée, ils indiquent le temps restant jusquau
démarrage du programme (voir page ci-contre).
Voyant HUBLOT VERROUILLÉ: indique si la porte
est verrouillée (voir page ci-contre).
Touche avec voyant MARCHE/PAUSE: pour
démarrer les programmes ou les interrompre
momentanément.
N.B.: pour effectuer une pause du lavage en cours,
appuyer sur cette touche, le voyant correspondant se
mettra à clignoter en orange tandis que celui de la
phase en cours restera allumé fixe. Si le voyant
HUBLOT VERROUILLÉ
est éteint, on peut ouvrir
la porte.
Pour faire redémarrer le lavage exactement de
lendroit il a été interrompu, appuyer une nouvelle
fois sur la touche.
Description du lave-linge et
démarrage dun programme
Bouton
TEMPÉRATURE
Tiroir à produits lessiviels
Voyants
DÉROULEMENT
CYCLE/DÉPART DIFFÉRÉ
Touches avec voyants
FONCTION
Touche
MARCHE/
ARRÊT
Bouton
ESSORAGE
Voyant
HUBLOT
VERROUILLÉ
Touche avec voyant
MARCHE/
PAUSE
Bandeau de commandes
Bouton
PROGRAMMES
FR
17
Voyants
Les voyants fournissent des informations importantes.
Voilà ce quils signalent:
Départ différé
Si la fonction Départ différé a été activée (voir
Personnalisations), le voyant correspondant au temps
sélectionné se mettra à clignoter, après avoir lancé le
programme :
Au fur et à mesure que le temps passe, le temps
restant est affiché avec clignotement du voyant
correspondant.
Quand le temps sélectionné touche à sa fin, le voyant
clignotant séteint et le programme sélectionné
démarre.
Voyants phase en cours
Une fois que le cycle de lavage sélectionné a
démarré, les voyants sallument progressivement pour
indiquer son stade davancement:
Touches fonction et voyants correspondants
La sélection dune fonction entraîne lallumage du
voyant correspondant.
Si la fonction sélectionnée est incompatible avec le
programme sélectionné, le voyant correspondant se
met à clignoter et la fonction nest pas activée.
En cas de sélection dune fonction incompatible avec
une autre précédemment sélectionnée, la seule à
être activée sera celle choisie en dernier.
Voyant hublot verrouillé:
Le voyant allumé indique que le hublot est verrouillé
pour empêcher toute ouverture accidentelle. Pour
éviter dendommager lappareil, attendre que le
voyant cesse de clignoter avant douvrir la porte.
N.B: si la fonction DÉPART DIFFÉRÉ est activée, le
hublot ne souvre pas. Pour louvrir il faut appuyer sur
la touche MARCHE/PAUSE qui met lappareil en
pause.
Un clignotement rapide du voyant MARCHE/PAUSE
(orange) simultané à celui des fonctions signale une
anomalie (voir Anomalies et remèdes).
Démarrage dun programme
1. Allumer le lave-linge en appuyant sur la touche MARCHE/ARRÊT. Tous les voyants sallument pendant
quelques secondes puis séteignent, seul le voyant MARCHE/PAUSE flashe.
2. Charger le linge et fermer le hublot.
3. Sélectionner à laide du bouton PROGRAMMES le programme désiré.
4. Sélectionner la température de lavage (voir Personnalisations).
5. Sélectionner la vitesse dessorage (voir Personnalisations).
6. Verser les produits lessiviels et les additifs (voir Produits lessiviels et linge).
7. Sélectionner les fonctions désirées.
8. Appuyer sur la touche MARCHE/PAUSE pour démarrer le programme, le voyant correspondant vert restera
allumé en fixe.
Pour annuler le cycle sélectionné, appuyer sur la touche MARCHE/PAUSE pour placer lappareil en pause et
choisir un nouveau cycle.
9. A la fin du programme, le voyant
sallume. Le voyant HUBLOT VERROUILLÉ séteint pour signaler que le
hublot peut être ouvert. Sortir le linge et laisser le hublot entrouvert pour faire sécher le tambour.
Eteindre le lave-linge en appuyant sur la touche MARCHE/ARRÊT.
Lavage
Rinçage
Essorage
Vidange
Fin de Lavage
18
FR
Programmes
Les données dans le tableau sont reprises à titre indicatif.
Pour tous les instituts qui effectuent ces tests :
1) Programme de contrôle selon la norme EN 60456: sélectionner le programme 6 et une température de 60°C.
2) Programme coton long: sélectionner le programme 1 et une température de 40°C.
3) Programme coton court: sélectionner le programme 2 et une température de 40°C.
Programmes
Tableau des programmes
Description du Programme
Te m p .
maxi.
(°C)
Vitesse
maxi
(tours
minute)
Produits lessiviels
Charge
maxi
(Kg)
Durée
cycle
Javel Lavage
Assou
-
plissant
Programmes Spécial
6
Anti-bactérien:
blancs extmement sales.
90° 1200
ll l
7170
6
Anti-bactérien (1):
blancs et couleurs résistantes très sales.
60° 1200 -
ll
7153
7
Bonne Nuit:
couleurs délicates peu sales.
40° 800 -
ll
4290
8
Bébé:
couleurs délicates très sales.
40° 800 -
ll
2 118
9
Chemises
40° 600 -
ll
270
10
Soie/Voilages:
pour linge en soie, viscose, lingerie.
30° 0 -
ll
155
11
Laine:
pour laine, cachemire, etc.
40° 600 -
ll
1,5 55
Programmes Quotidien
1
Coton:
blancs et couleurs résistantes très salesi.
60° 1200
ll l
7122
1
Coton (2):
blancs et couleurs délicates très sales.
40° 1200
ll l
7 115
2
Coton (3):
blancs peu sales et couleurs délicates.
40° 1200
ll l
785
3
Synthétique:
couleurs résistantes très sales.
60° 800 -
ll
385
3
Synthétique:
couleurs résistantes peu sales.
40° 800 -
ll
370
4
MIX 30':
pour rafraîchir rapidement du linge peu sale (ne convient pas pour
la laine, la soie et le linge à laver à la main).
30° 800 -
ll
330
5
MIX 15':
pour rafraîchir rapidement du linge peu sale (ne convient pas pour
la laine, la soie et le linge à laver à la main).
30° 800 -
ll
1,5 15
Cycle
A
Rinçage - 1200 - -
l
736
B
Rinçage délicat - 800 - -
l
331
C
Essorage - 1200 - - - 716
D
Essorage licat - 800 - - - 312
E
Vidange - 0 - - - 72
Programmes spéciaux
Anti-bactérien (programme 6). Un programme hautes températures qui prévoit lutilisation de produits javelisés à des
températures supérieures à 60°C. Pour blanchir, verser le produit javelisé, les lessives et les additifs dans les
compartiments correspondants (voir paragraphe Tiroir à produits lessiviels).
Bonne nuit (programme 7). Cest un cycle silencieux qui permet de faire fonctionner le lave-linge la nuit quand le tarif
délectricité est plus bas. Ce programme est spécialement conçu pour les synthétiques et le coton. A la fin du cycle
lappareil sarrête, cuve pleine. Pour procéder à lessorage et à la vidange, appuyer sur la touche MARCHE/PAUSE, à
défaut, lappareil procédera automatiquement au bout de 8 heures à lessorage et à la vidange de leau.
Bébé (programme 8). Programme spécial, idéal pour le lavage des vêtements denfants souvent très sales, il élimine
toute trace de lessive du linge pour protéger leur peau délicate et éviter tout risque dallergie. Spécialement conçu pour
diminuer la charge bactérienne, ce cycle utilise une plus grande quantité deau et optimise leffet des additifs
désinfectants spécifiques ajoutés à la lessive.
En fin de lavage, lappareil fait tourner le tambour lentement pour éviter de froisser le linge. Pour compléter le cycle
appuyer sur la touche MARCHE/PAUSE.
Mix 30 (programme 4) spécialement conçu pour laver du linge peu sale en un rien de temps: il ne dure que 30 minutes
et permet ainsi de faire des économies dénergie et de temps. La sélection de ce programme (4 à 30°C) permet de
laver ensemble des textiles différents (sauf laine et soie) en ne dépassant pas 3 kg de charge.
Mix 15 (programme 5) spécialement conçu pour laver du linge peu sale en un rien de temps: il ne dure que 15 minutes
et permet ainsi de faire des économies dénergie et de temps. La sélection de ce programme (5 à 30°C) permet de
laver ensemble des textiles différents (sauf laine et soie) en ne dépassant pas 1,5 kg de charge.
FR
19
Sélection de la température
Tourner le bouton TEMPÉRATURE pour sélectionner la température de lavage (voir Tableau des programmes).
La température peut être abaissée jusquau lavage à froid (
).
La machine interdira automatiquement toute sélection dune température supérieure à la température maximale
prévue pour chaque programme.
Sélection de lessorage
Tourner le bouton ESSORAGE pour sélectionner la vitesse dessorage du programme sélectionné.
Les vitesses maximales prévues pour les programmes sont:
Programmes Vitesse maximale
Coton 1200 tours/minute
Synthétiques 800 tours/minute
Laine 600 tours/minute
Soie vidange seule
La vitesse dessorage peut être réduite ou lessorage supprimé en sélectionnant le symbole
.
La machine interdira automatiquement tout essorage à une vitesse supérieure à la vitesse maximale prévue pour
chaque programme.
Fonctions
Les différentes fonctions de lavage prévues par le lave-linge permettent dobtenir la propreté et le blanc souhaités.
Pour activer les fonctions:
1. appuyer sur la touche correspondant à la fonction désirée;
2. lallumage du voyant correspondant signale que la fonction est activée.
Remarque: Le clignotement rapide du voyant signale que la fonction correspondante nest pas disponible pour le
programme sélectionné.
Départ différé
Pour différer la mise en marche de la machine jusquà 12 heures.
Appuyer plusieurs fois de suite sur la touche jusquà ce que le voyant correspondant au retard souhaité sallume. A
la cinquième pression sur la touche, la fonction se désactive.
N.B: Après avoir appuyé sur la touche MARCHE/PAUSE, le retard programmé ne peut être modifié que pour le
diminuer.
Il est activé avec tous les programmes.
Repassage facile
En cas de sélection de cette fonction, le lavage et lessorage seront dûment modifiés pour réduire le froissage. En
fin de cycle, le lave-linge fait tourner le tambour lentement, le voyant de la fonction REPASSAGE FACILE et celui
de MARCHE/PAUSE se mettent à clignoter (orange), la phase
reste allumée en fixe. Pour compléter le cycle, il
faut appuyer sur la touche MARCHE/PAUSE ou sur la touche REPASSAGE FACILE.
Pour le programme Soie (10) lappareil arrive au bout du cycle en laissant le linge tremper, le voyant de la fonction
REPASSAGE FACILE et celui de MARCHE/PAUSE se mettent à clignoter (orange), la phase RINCAGE reste
allumée en fixe. Pour vidanger leau et pouvoir sortir le linge, il faut appuyer sur la touche MARCHE/PAUSE ou sur
la touche REPASSAGE FACILE.
Cette option nest pas activable avec les programmes 4, 5, 6, 7, 8, 11, C, D, E.
Super rinçage
La sélection de cette fonction permet daugmenter lefficacité du rinçage et déliminer toute trace de lessive. Elle
est très utile en cas de peaux particulièrement sensibles.
Cette option nest pas activable avec les programmes 4, 5, C, D, E.
Super lavage
Grâce à l'utilisation d'une plus grande quantité d'eau au cours de la phase initiale du cycle et à l'emploi de
davantage de temps, cette fonction permet d'obtenir un lavage très performant.
Cette option nest pas activable avec les programmes 4, 5, 6, 10, 11, A, B, C, D, E.
Personnalisations
20
FR
Produits lessiviels et linge
Tiroir à produits lessiviels
Un bon résultat de lavage dépend aussi dun bon
dosage de produit lessiviel: un excès de lessive ne
lave pas mieux, il incruste lintérieur du lave-linge et
pollue lenvironnement.
Ne pas utiliser de lessives pour lavage à la main,
elles moussent trop.
Sortir le tiroir à produits
lessiviels et verser la
lessive ou ladditif comme
suit.
bac 1: Lessive prélavage (en poudre)
Avant dintroduire la lessive, sassurer que le bac
supplémentaire 4 nest pas présent.
bac 2: Lessive lavage (en poudre ou liquide)
Verser la lessive liquide juste avant la mise en marche.
bac 3: Additifs (assouplissant, etc.)
Lassouplissant ne doit pas déborder de la grille.
bac supplémentaire 4: Produit javelisé
Cycle blanchissage
Le blanchissage nest possible quavec les
programmes 1, 2, 6.
Verser le produit javelisé dans le bac supplémentaire 4,
la lessive et lassouplissant dans les bacs
correspondants, puis sélectionner un des
programmes sus-indiqués.
Conseillé en cas de linge en coton très sale.
Triage du linge
Trier correctement le linge daprès:
- le type de textile / le symbole sur létiquette.
- les couleurs: séparer le linge coloré du blanc.
Vider les poches et contrôler les boutons.
Ne pas dépasser les valeurs indiquées
correspondant au poids de linge sec :
Textiles résistants: 7 kg max.
Textiles synthétiques: 3 kg max.
Textiles délicats: 2 kg max.
Laine: 1,5 kg max.
Combien pèse le linge ?
1 drap 400-500 g
1 taie doreiller 150-200 g
1 nappe 400-500 g
1 peignoir 900-1200 g
1 serviette éponge 150-250 g
MAX
1
2
4
3
Linge ou vêtements particuliers
Chemises: sélectionner le programme 9 approprié
au lavage de chemises de couleurs et textiles
différents.
Il en prend le plus grand soin en réduisant le
froissage.
Soie: sélectionner le programme de lavage spécial 10
pour vêtements en soie. Il est conseillé dutiliser une
lessive spéciale pour linge délicat.
Rideaux: pliez-les bien et glissez-les dans une taie
d'oreiller ou dans un sac genre filet. Sélectionner le
programme 10.
Laine: Ariston est le seul lave-linge à avoir obtenu le
prestigieux label Woolmark Platinum Care (M.0508)
délivré par The Woolmark Company qui garantit le
lavage à la machine de tous les vêtements en laine, y
compris ceux qui portent létiquette lavage à la main
uniquement
. Grâce au programme 11 on peut
donc laver à la machine, en toute tranquillité, tous les
vêtements en laine (max. 1,5 kg) avec des
performances de lavage optimales.
Système déquilibrage de la charge
Avant tout essorage, pour éviter toute vibration
excessive et répartir le linge de façon uniforme, le
lave-linge fait tourner le tambour à une vitesse
légèrement supérieure à la vitesse de lavage. Si au
bout de plusieurs tentatives, la charge nest toujours
pas correctement équilibrée, lappareil procède à un
essorage à une vitesse inférieure à la vitesse
normalement prévue. En cas de déséquilibre excessif,
le lave-linge préfère procéder à la répartition du linge
plutôt quà son essorage. Pour une meilleure
répartition de la charge et un bon équilibrage, nous
conseillons de mélanger de grandes et petites pièces
de linge.
1 / 1

Indesit AR7L 125 (EX) Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi

dans d''autres langues