Hornby Hobbies HM7000-Next18TXS Module Manuel utilisateur

Taper
Manuel utilisateur
The HM7000-Next18(8)TXS module is designed to comply with the FCC statement. FCC
ID is 2ACUF-7000818TX The host system using HM7000-Next18(8)TXS should have label
indicated it contain modular’s FCC ID : 2ACUF-7000818TX.
This radio module must not installed to co-locate and operating simultaneously with other
radios in host system, additional testing and equipment authorization may be required to
operating simultaneously with other radio.
The HM7000-Next18(8)TXS module is designed to comply with the ISED statement. The
module ID is 12075A-HM7000818TX. The host system using HM7000-N
i
ext18(8)TXS,
should have label indicated it contain modular’s IC : 12075A-HM7000818TX.
This radio module must not installed to co-locate and operating simultaneously with other
radios in host system, additional testing and equipment authorization may be required to
operating simultaneously with other radio.
Le module HM7000-Next18(8)TXS est conçu pour se conformer à la déclaration ISDE.
Le numéro d’identification du module est 12075A-HM7000818TX. Le système hôte
utilisant HM7000-N
ii
ext18(8)TXS doit avoir une étiquette indiquant qu’il contient l’IC
modulaire: 12075A-HM7000818TX.
Ce module radio ne doit pas être installé pour co-localiser et fonctionner simultanément
avec d’autres radios dans le système hôte, des tests supplémentaires et une autorisation
d’équipement peuvent être nécessaires pour fonctionner simultanément avec d’autres
radios.
List of applicable FCC rules:
The module complies with FCC Part 15.247.
Summarize the specific operational use conditions:
The module has been certified for Fix, Mobile applications.
This transmitter must not be colocated or operating in conjunction with any other antenna or
transmitter.
Limited module procedures:
This module is limited to Hornby Corporation use ONLY.
The module has no RF shielding and will be installed in toy track car.
which belong to signal module Standard requires:
Clear and specific instructions describing the conditions, limitations and procedures for third
parties to use and/or integrate the module into a host device (see Comprehensive integration
instructions below).
Installation Notes:
1) HM7000-Next18(8)TXS Module Power supply range is DC 14V~16V, when you use
HM7000-Next18(8)TXS Module design product, the power supply cannot exceed this
range.
2) Make sure the module pins correctly installed.
3) Make sure that the module does not allow users to replace or demolition
4) Any modifications to the module model HM7000-Next18(8)TXS may invalidate regulatory
approvals or may necessitate notifications to the relevant regulatory authorities.
5) OEM must inform iRobot Compliance of any changes which may require the Class I
or Class II permissive changes for the FCC.
Antennas
The module have an PCB antenna
Information on test modes and additional testing requirements:
When testing host product, the host manufacture should follow FCC KDB Publication 996369
D04 Module Integration Guide for testing the host products. The host manufacturer may
operate their product during the measurements. In setting up the configurations, if the pairing
and call box options for testing does not work, then the host product manufacturer should
coordinate with the module manufacturer for access to test mode software.
Additional testing, Part 15 Subpart B disclaimer:
The modular transmitter is only FCC authorized for the specific rule parts (FCC Part 15.247)
list on the grant, and that the host product manufacturer is responsible for compliance to any
other FCC rules that apply to the host not covered by the modular transmitter grant of
certification. The final host product still requires Part 15 Subpart B compliance testing with the
modular transmitter installed when contains digital circuity.
Information on test modes and additional testing requirements:
When testing host product, the host manufacture should follow FCC KDB Publication 996369
D04 Module Integration Guide for testing the host products. The host manufacturer may
operate their product during the measurements.
  • Page 1 1
  • Page 2 2

Hornby Hobbies HM7000-Next18TXS Module Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues