Honeywell H600A Manuel utilisateur

Marque: Honeywell

Modèle: H600A

Taper: Manuel utilisateur

INSTALLATION INSTRUCTIONS

60-0080-03

H600A

Humidity Control

APPLICATION

The H600 is a humidity control which controls

humidification and dehumidification equipment

within a range of 20 to 80 percent RH. It has an SPDT

switch to operate humidification equipment on RH

fall or dehumidification equipment on RH rise. The

sensing element is a thin moisture-sensitive nylon

ribbon wound around three bobbins. This

construction enables the control to respond to small

changes in relative humidity over a wide ambient

temperature range. The differential is 4 to 6 percent

RH and is not adjustable. All models have a locking

cover, and the setting knob acts as the cover removal

tool.

SPECIFICATIONS

Model: H600A Humidifier and Dehumidifier Control.

Switching: SPDT.

Table 1. Electrical Rating.

Relative Humidity Range: 20-80 %.

Differential: 4-6 % RH, fixed.

Max. Ambient Temperature: 50 °C.

Set point adjustment: Removable knob.

Dimensions: See Figure 1.

INSTALLATION

Location

Select a location about 1.5 m above the floor on an

inside wall with good natural air circulation at

average room temperatures.

Avoid:

—hot spots due to concealed pipes, warm

air ducts, radiator, appliances or exposure

to sun;

—cold spots due to location on an outside

wall, an unheated room on the other side

of partition or drafts from stairwells or

doors;

—dead spots due to lack of circulation

behind doors or in corners.

The ambient temperature of the location chosen

must not exceed 50 °C.

Dehumidifier

(Red to Yellow)

Humidifier

(Red to Blue)

120 Vac 240 Vac 120 Vac 240 Vac

Full Load 7.5 A 3.85 A 4.4 A 2.2 A

Locked Rotor 45.0 A 22.8 A 26.4 A 13.2 A

Resistive — — 8.0 A 4.0 A

H600A HUMIDITY CONTROL

60-0080—03 2

Fig. 1. Dimensions in mm.

Mounting

1. Use the setting knob to loosen the cover locking

screw. Remove cover.

2. Remove the backplate from the control assembly

by loosening the captive mounting screw and

sliding the control down and to the right (See

Figures 2 and 3).

3. Mount the backplate to the wall using the two

screws provided.

4. Attach control to backplate by slipping it under

tabs and tightening the captive mounting screw

(See Figure 2).

5. Connect wires as shown in Figure 5.

6. Replace cover and tighten the locking screw with

setting knob supplied.

Fig. 2. Cover removed.

Fig. 3. Mounting the H600A.

H600A HUMIDITY CONTROL

The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates.

Ce produit est fabriqué par Resideo Technologies, Inc. et ses sociétés affiliées.

Dieses Produkt wird von Resideo Technologies, Inc. und seinen Tochtergesellschaften hergestellt.

Questo prodotto è fabbricato da resideo Technologies, Inc. e dai suoi affiliati.

www.resideo.com

Resideo Technologies, Inc.

1985 Douglas Drive North, Golden Valley, MN 55422

1-800-468-1502

60-0080—03 M.S. Rev. 10-21 | Printed in United States

Fig. 4. The H600A is suitable for surface as well as through-the-wall wiring.

WIRING

CAUTION

Disconnect power supply before making

wiring connections to prevent electrical

shock and equipment damage.

All wiring must comply with local electrical codes.

Follow equipment manufacturer’s instructions, if

available; otherwise proceed as follows:

Insert wiring through hole in back plate or through

conduit entry (see Figure 2). If conduit entry is not

used, hole must be closed with the rubber plug

provided. If the hole in the mounting plate is exposed

to an opening in the wall, plug the opening to prevent

drafts from affecting the humidistat operation.

Connect wires as shown in Figure 5.

Fig. 5. H600A Wiring Diagram.

Connect red and blue leadwires to humidifier, or red

and yellow leadwires to dehumidifier.

SETTING

Adjust the relative humidity setting with the

removable setting knob provided.

M38555

H600A

BLUE

RED

YELLOW

TO HUMIDIFIER

TO DEHUMIDIFIER

H600A HUMIDITY CONTROL

60-0080—03 4

H600A HUMIDITY CONTROL

5 60-0080—03

H600A HUMIDITY CONTROL

60-0080—03 6

H600A HUMIDITY CONTROL

7 60-0080—03

H600A HUMIDITY CONTROL

60-0080—03 8

H600A HUMIDITY CONTROL

9 60-0080—03

H600A HUMIDITY CONTROL

60-0080—03 10

H600A HUMIDITY CONTROL

11 60-0080—03

H600A HUMIDITY CONTROL

The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates.

Ce produit est fabriqué par Resideo Technologies, Inc. et ses sociétés affiliées.

Dieses Produkt wird von Resideo Technologies, Inc. und seinen Tochtergesellschaften hergestellt.

Questo prodotto è fabbricato da resideo Technologies, Inc. e dai suoi affiliati.

www.resideo.com

Resideo Technologies, Inc.

1985 Douglas Drive North, Golden Valley, MN 55422

1-800-468-1502

60-0080—03 M.S. Rev. 10-21 | Printed in United States