GE Profile UVI7361SWSS Le manuel du propriétaire

Catégorie
Hottes
Taper
Le manuel du propriétaire
Write the model and serial
numbers here:
Model # _________________
Serial # _________________
You can find them on a label on
the inside of the hood.
49-7000198 Rev. 0 03-23 GEA
UVI7361
OWNER’S MANUAL &
INSTALLATION
INSTRUCTIONS
ISLAND CHIMNEY
VENT HOODS
SAFETY INFORMATION ............ 3
USING THE HOOD
Light Controls ........................... 5
Vent Controls ........................... 5
CARE AND CLEANING
Metal Grease Filter .......................6
Charcoal Filter ........................... 6
Stainless Steel Surfaces ................... 7
LED Lights .............................. 7
INSTALLATION INSTRUCTIONS .. 8
Installation Preparation ................... 9
Vented to the Outside ....................16
TROUBLESHOOTING TIPS .........21
LIMITED WARRANTY ............. 23
CONSUMER SUPPORT ............24
ESPAÑOL
For a Spanish version of this
manual, visit our Website at
www.GEAppliances.com.
Para consultar una version
en español de este manual
de instrucciones, visite nuestro
sitio de internet
GEAppliances.com.
FRANÇAIS
For a French version of this
manual, visit our Website at
www.GEAppliances.ca.
Pour un version français de
ce manuel d’utilisation, veuillez
visiter notre site web à l’adresse
GEAppliances.ca.
249-7000198 Rev. 0
THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation and design that goes into every GE Appliances
product, and we think you will too. Among other things, registration of your appliance ensures that we
can deliver important product information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are available in the
Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration
card included in the packing material.
49-7000198 Rev. 0 3
SAFETY INFORMATION
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
WARNING TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
B. Before servicing or cleaning unit, switch power off
at service panel and lock the service disconnecting
means to prevent power from being switched on
accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent
warning device, such as a tag, to the service panel.
C. Do not use this unit with any solid-state speed
control device.
D. This unit must be grounded.
CAUTION For general ventilating use only. Do
not use to exhaust hazardous or explosive materials
and vapors.
CAUTION To reduce risk of fire and to properly
exhaust air, be sure to duct air outside. Do not vent
exhaust air into spaces within walls or ceilings or into
attics, crawl spaces or garages.
WARNING TO REDUCE THE RISK OF INJURY
TO PERSONS IN THE EVENT OF A RANGE TOP
GREASE FIRE, OBSERVE THE FOLLOWING*:
A. SMOTHER FLAMES with a close-fitting lid, cookie
sheet or metal tray, then turn off the burner. BE
CAREFUL TO PREVENT BURNS. If the flames
do not go out immediately, EVACUATE AND CALL
THE FIRE DEPARTMENT.
B. NEVER PICK UP A FLAMING PAN— You may be
burned.
C. DO NOT USE WATER, including wet dishcloths or
towels - a violent steam explosion will result.
D. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher,
and you already know how to operate it.
2. The fire is small and contained in the area where
it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by
NFPA.
449-7000198 Rev. 0
SAFETY INFORMATION
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
WARNING TO REDUCE THE RISK OF A
RANGE TOP GREASE FIRE:
A. Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on low or
medium settings.
B. Always turn hood ON when cooking on high heat or
when flambéing food (i.e. Crepes Suzette, Cherries
Jubilee, Peppercorn Beef Flambé).
C. Clean ventilating fans frequently. Grease should not
be allowed to accumulate on fan or filter.
D. Use proper pan size. Always use cookware
appropriate for the size of the surface element.
WARNING TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Installation work and electrical wiring must be
done by qualified person(s) in accordance with all
applicable codes and standards, including fire-rated
construction.
B. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guidelines and safety standards, such as
those published by the National Fire Protection
Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE) and the local code authorities.
When applicable, install any makeup (replacement)
air system in accordance with local building
code requirements. Visit GEAppliances.com for
available makeup air solutions.
C. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
D. Ducted fans must always be vented to the outdoors.
F. Turn off breaker to adjacent rooms while working.
WARNING TO REDUCE THE RISK OF FIRE,
USE ONLY METAL DUCTWORK.
Ŷ Do not attempt to repair or replace any part of your
hood unless it is specifically recommended in this
manual. All other servicing should be referred to a
qualified technician.
49-7000198 Rev. 0 5
Controls
USING THE HOOD: Controls
3 2 1
1. MEMORY/OFF: To set the memory:
A. Press the MEMORY/OFF button.
B. Set your desired fan and light settings.
C. Press the MEMORY/OFF button again to save
these settings.
With your desired settings in memory, press the
MEMORY/OFF button to restore the fan and light
levels to their saved settings. These settings will
remain in memory until they are changed or loss of
power occurs.
To turn off the hood, press the MEMORY/OFF button.
2. LIGHT: Press + or to increase or decrease light
level to desired setting. There are 2 light levels (LOW,
HIGH) and OFF. If you continue to press the + or
buttons, the light will cycle back through the settings.
3. FAN. Press + or to increase or decrease fan level
to your desired setting. There are 4 fan levels (LOW,
MED, HIGH, BOOST) and OFF. If you continue to
press the + orbuttons, the fan will cycle back
through the settings.
NOTE: There is an audible “beep” each time a button
is pressed. This is normal.
NOTE: The collars around the buttons will illuminate
when pressed. This is normal. The collars will
automatically turn off if the hood is turned off.
HEAT SENSOR:
This hood is equipped with a heat sensor that will turn
on the fan if excessive temperatures are detected (over
Û&Û)DERYHWKHFRRNLQJVXUIDFH7KHKRRGZLOO
return to its normal operation once the heat sensor
GHWHFWVWHPSHUDWXUHVEHORZÛ&Û)
NOTE: If the hood is OFF or on LOW fan speed, the
WHPSHUDWXUHVDERYHÛ&Û)DUHGHWHFWHGWKHQWKH
fan will automatically adjust to MED speed. You may
adjust the fan speed to HIGH or BOOST, but you will
not be able to adjust the fan speed to LOW or OFF until
WHPSHUDWXUHVEHORZÛ&Û)DUHGHWHFWHG
NOTE: The collars around the buttons may not illuminate
if the heat sensor is activated. This is normal.
649-7000198 Rev. 0
Filters
CARE AND CLEANING: Filters
Metal Grease Filter
The metal filter traps grease released by foods from the
cooktop. The filter also helps prevent flames (from food,
grease) from damaging the inside of the hood.
For this reason, the filter must ALWAYS be in place when
the hood is in use. The grease filter is dishwasher-safe
and should be cleaned every 6 months, or as needed.
To remove:
Pull downward on the filter lock to release the filter.
To replace:
Fit the tabs at the end of the filter into the slots in left
side of the filter opening. Lift up the right side of the filter
and push gently until the filter locks into place. Make
sure the filter lock is in the closed position to secure the
filter.
To clean, swish the filter in hot soapy water and rinse
in clean water or wash it in the dishwasher. Do not use
abrasive cleansers.
NOTE: Some discoloration will occur in the dishwasher.
Charcoal Filter
For recirculating installation only
If the model is not vented to the outside, the air will be
recirculated through a disposable charcoal filter that
helps remove smoke and odors.
The charcoal filter should be replaced when it is
noticeably dirty or discolored (usually after 6 to 12
months, depending on hood usage).
NOTE: DO NOT rinse, or put charcoal filter in an
automatic dishwasher.
The charcoal filter cannot be cleaned. It must be
replaced.
2UGHU&KDUFRDO)LOWHU:%;
To inquire about purchasing replacement charcoal filters
or to find the location of a dealer nearest you, please call
our toll-free number:
1DWLRQDO3DUWV&HQWHU
To remove:
1. Remove the metal filter—see Metal grease filter
section.
2. Remove the charcoal filter by pushing in on both
locking tab handles to release.
To replace:
1. Insert the charcoal filter into the opening. Push the
locking tab handles toward the center and release to
engage the locking tabs.
2. Replace the metal filter—see Metal grease filter
section.
Be sure electrical power is off and all surfaces are cool before cleaning or servicing any part of the vent hood.
Locking tab handle
Locking tab handle
49-7000198 Rev. 0 7
Care and Cleaning
Stainless Steel Surfaces
'RQRWXVHDVWHHOZRROSDGLWZLOOVFUDWFKWKHVXUIDFH
To clean the stainless steel surface, use warm sudsy
water or a stainless steel cleaner or polish. Always wipe
the surface in the direction of the brush line. Follow
the cleaner instructions for cleaning the stainless steel
surface. Cleaners with oxalic acid such as Bar Keepers
Friend Soft Cleanser™ will remove surface rust, tarnish,
and small blemishes. To receive a $2.00 coupon for
a trial sample of Bar Keepers Friend Soft Cleanser™
follow the link below or scan the QR Code.
barkeepersfriend.com/ge
Use only a liquid cleanser free of grit and rub in the
direction of the brush lines with a damp soft sponge.
To inquire about purchasing stainless steel appliance
cleaner or polish, or to find the location of a dealer
nearest you, please call our toll-free number:

GEApplianceParts.com
CARE AND CLEANING
LED Lights
The LED lights are replaceable by a service technician only. See the Limited Warranty section for service
contact information.
49-7000198 Rev. 0
Installation
Instructions
If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737)
or visit our website at: GEAppliances.com
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Ŷ IMPORTANTSave these instructions
for local inspector’s use.
Ŷ IMPORTANTObserve all governing
codes and ordinances.
Ŷ Note to Installer – Be sure to leave these
instructions with the Consumer.
Ŷ Note to Consumer – Keep these instructions for
future reference.
Ŷ Skill level – Installation of this vent hood requires
basic mechanical and electrical skills.
Ŷ Completion time – Approximately 4 to 6 hours
Ŷ Proper installation is the responsibility of the
installer.
Ŷ Product failure due to improper installation is not
covered under the Limited Warranty.
PRODUCT DIMENSIONS
INSTALLATION CLEARANCES
These vent hoods are
designed to be installed
onto a wall with no above
cabinets.
Install these hoods
between the required
24” minimum and
36” recommended
maximum above the
cooking surface.
The vent hood must be
installed between the
required 24” minimum
and 36” recommended maximum above the cooking
surface. The hood installation height above the
cooking surface depends upon ceiling height and
duct cover limitations. The telescopic duct cover
conceals the ductwork running from the top of the
hood to the ceiling.
NOTE: Installation height should be measured from
the cooking surface to the lowest part of the hood.
This hood must be installed onto a wall. It can be
vented to the outdoors, or it can be installed for
recirculating operation. Recirculating Kit included
with hood.
Island Chimney Vent Hood
INSTALLATION INSTRUCTIONS
CAUTION Due to the weight and size of
these vent hoods and to reduce the risk of personal
injury or damage to the product, TWO PEOPLE
ARE REQUIRED FOR PROPER INSTALLATION.
FOR YOUR SAFETY:
WARNING Before beginning the installation,
switch power off at service panel and lock the
service disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag, to
the service panel.
* For supplied duct cover ceiling height for vented installation and
recirculating installation, refer to the table on page 12.
´
*Height to
ceiling
´ ´
´
´
*Height to Ceiling
Vented Recirculating
Min ´ ´
Max ´ ´
24” Required Min.
36” Recommended Max.
36” Typical
49-7000198 Rev. 0 9
INSTALLATION INSTRUCTIONS
Installation Preparation
PREPARE TO INSTALL THE HOOD
ADVANCE PLANNING
Duct Install Planning
Ŷ Determine the exact location of the vent hood.
Ŷ Use rigid metal ductwork only.
Ŷ Plan the route for venting exhaust to the
outdoors. To maximize the ventilation
performance of the vent system:
1. Minimize the duct run length and number of
transitions and elbows.
2. Maintain a constant duct size.
3. Seal all joints with duct tape to prevent any
leaks.
4. Do not use any type of flexible ducting.
Ŷ Use the shortest and straightest duct route
possible.
Ŷ Install a roof cap with damper at the exterior
opening. Order the cap and any transitions and
length of duct needed in advance.
Ŷ When applicable, install any makeup
(replacement) air system in accordance with local
building code requirements. Visit
GEAppliances.com for available makeup air
solutions.
Ceiling Framing for Adequate Support
Ŷ These vent hoods are heavy. Adequate structural
support must be provided. The ceiling structure
must be capable of supporting the weight of the
hood and any inadvertent user contact loads
(approximately 200 pounds). The hood support
frame will be supported by 2 x 4 cross framing.
Ŷ Installation will be easier if the vent hood is
installed before the cooktop or countertop below
is installed.
Duct Covers
Ŷ All models are shipped with duct covers. For
supplied duct cover ceiling heights for vented
installation and recirculating installation, refer to
table on page 12.
POWER SUPPLY
IMPORTANT—(Please read carefully)
WARNING
FOR PERSONAL SAFETY, THIS APPLIANCE
MUST BE PROPERLY GROUNDED.
Remove house fuse or open circuit breaker before
beginning installation.
Do not use an extension cord or adapter plug with
this appliance. Follow National Electrical Codes or
prevailing local codes and ordinances.
Electrical Supply
This vent hood must be supplied with 120V, 60Hz,
and connected to an individual, properly grounded
branch circuit, and protected by a 15 or 20 amp
circuit breaker or time delay fuse.
Ŷ Wiring must be 2 wire with ground.
Ŷ If the electrical supply does not meet the above
requirements, call a licensed electrician before
proceeding.
Ŷ Route house wiring in the ceiling, as close to the
installation location as possible. Allow additional
length from ceiling joists to reach the junction box
on the bottom of the hood support frame.
Ŷ Connect the wiring to the house wiring in
accordance with local codes.
Grounding Instructions
The grounding conductor must be connected to
a ground metal, permanent wiring system, or an
equipment-grounding terminal or lead on the hood.
WARNING
The improper connection of equipment-grounding
conductor can result in a risk of electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded.
This Hood MUST Use an 8” Round Duct. It Can Transition to a 3-1/4” x 12” Duct.
DO NOT use flexible plastic ducting.
NOTE: Any home ventilation system, such as a ventilation hood, may interrupt the proper flow of combustion
air and exhaust required by fireplaces, gas furnaces, gas water heaters and other naturally vented systems.
To minimize the chance of interruption of such naturally vented systems, follow the heating equipment
manufacturer’s guidelines and safety standards such as those published by NFPA and ASHRAE. When
applicable, install any makeup (replacement) air system in accordance with local building code requirements.
Visit GEAppliances.com for available makeup air solutions.
10 49-7000198 Rev. 0
Installation Preparation
INSTALLATION INSTRUCTIONS
REMOVE THE PACKAGING
CAUTION Wear gloves to protect against
sharp edges.
Ŷ5HPRYHWKHGXFWFRYHUV
Ŷ5HPRYHWKHKDUGZDUHEDJOLWHUDWXUHSDFNDJHDQG
other boxed parts.
Ŷ5HPRYHDQGSURSHUO\GLVFDUGWKHSURWHFWLYH
plastic wrapping and other packaging materials.
TOOLS AND MATERIALS REQUIRED
(NOT SUPPLIED)
Pliers
:LUHFXWWHUVWULSSHU
Metal snips
Spirit level
Aluminized
Duct tape
Safety glasses
120V 60Hz. 15 or 20 Amp,
2-wire with ground, properly
grounded branch circuit
Step ladder
Saber saw or Key Hole saw
Phillips screwdriver
Strain relief for
junction box
´5RXQGPHWDO
duct, length to
suit installation
Hammer
(OHFWULFGULOOZLWK´
bits, #2 Phillips head
Flashlight
UL listed wire nuts
Pencil and tape measure
49-7000198 Rev. 0 11
INSTALLATION INSTRUCTIONS
Installation Preparation
CHECK INSTALLATION HARDWARE
Locate the hardware package packed with the hood and check contents.
RECIRCULATING KIT (Included)
Air deflector
36" HOOD
TEMPLATE
Cut one 1/2" Dia.
Wire Access Hole
as Needed
8-1/4" To
Centerline of
Pilot Holes
8-1/2"
FRONT OF HOOD
Cut one 1/2" Dia.
Wire Access Hole
as Needed
Cut one 1/2" Dia.
Wire Access Hole
as Needed
Cut one 1/2" Dia.
Wire Access Hole
as Needed
Drill 3/16" Pilot Holes
Approx. 1-1/2" Deep
4 Places
8-1/4" To
Centerline of
Pilot Holes
10-5/16" To
Centerline of
Pilot Holes
10-5/16" To
Centerline of
Pilot Holes
31-14772
Printed in Mexico 12-08 JR
4 Wood
screws
73 Hood attachment screws
(70 required, 3 extra)
Duct covers
Charcoal filter
C
Duct cover supports (2)
Template
Ceiling support
Horizontal support
Upper vertical supports (4)
Lower vertical supports (4)
4 Duct cover clips
Stainless steel filter
D
B
E
A
A
B
C
D
E
HARDWARE PACKAGE
Locate and count screws
Upper Lower
2 Leveling screws
12 49-7000198 Rev. 0
Installation Preparation
INSTALLATION INSTRUCTIONS
INSTALLATION CLEARANCES
These vent hoods are designed to be installed onto
a wall with no above cabinets.
Ŷ,QVWDOOWKHVHKRRGVEHWZHHQWKHUHTXLUHG´
minimum and 36” recommended maximum above
the cooking surface.
The vent hood must be installed between the
required 24” minimum and 36” recommended
maximum above the cooking surface. The hood
installation height above the cooking surface
depends upon ceiling height and duct cover
limitations. The telescopic duct cover conceals the
ductwork running from the top of the hood to the
ceiling.
NOTE: Installation height should be measured from
the cooking surface to the lowest part of the hood.
This hood must be installed onto a wall. It can be
vented to the outdoors, or it can be installed for
recirculating operation. Recirculating Kit included
with hood.
24” Required Min.
36” Recommended Max.
36” Typical
UVI7361
Upper Duct Cover 29.92
Lower Duct Cover 
Counter to Hood Height
Actual
Ceiling
Height
*Possible VENTED
Installation Height
*Possible
RECIRCULATING
Installation Height
7’ 11” 24” 24”
¶´ 24” to 25” 24” to 25”
¶´ 24” to 26” 24” to 26”
¶´ 24” to 27” 24” to 27”
¶´ ´WR´ ´WR´
¶´ 24” to 29” 24” to 29”
¶´ 24” to 30” 24” to 30”
¶´ 24” to 31” 24” to 31”
¶´ 24” to 32” 24” to 32”
¶´ 24” to 33” 24” to 33”
¶´ 24” to 34” 24” to 34”
¶´ 24” to 35” 24” to 35”
¶´ 24” to 36” 24” to 36”
9’ 0” 24” to 36” 24” to 36”
9’ 1” 24” to 36” 24” to 36”
9’ 2” 24” to 36” 24” to 36”
9’ 3” 24” to 36” 24” to 36”
9’ 4” 24” to 36” 24” to 36”
9’ 5” 25” to 36” 24” to 36”
9’ 6” 26” to 36” 24” to 36”
9’ 7” 27” to 36” 24” to 36”
¶´ ´WR´ 24” to 36”
9’ 9” 29” to 36” 24” to 36”
9’ 10” 30” to 36” 25” to 36”
9’ 11” 31” to 36” 26” to 36”
10’ 0” 32” to 36” 27” to 36”
10’ 1” 33” to 36” ´WR´
10’ 2” 34” to 36” 29” to 36”
10’ 3” 35” to 36” 30” to 36”
10’ 4” 36” 31” to 36”
10’ 5” 32” to 36”
10’ 6” 33” to 36”
10’ 7” 34” to 36”
¶´ 35” to 36”
10’ 9” 36”
* based on 36” countertop height
49-7000198 Rev. 0 13
CONSTRUCT CEILING SUPPORT
Plan the Location of the Hood and Ductwork
Ŷ Use a plumb bob to check the location. The
FRXQWHUWRSFRRNWRSEHORZWKHKRRGPXVWEH
centered with the hood.
Ŷ The hood should extend beyond the front and rear
edge of the cooking appliance.
Ŷ The duct in the ceiling must be centered over
the cooktop.
Ceiling Support Structure
Ŷ At the hood location, install cross framing between
ceiling joists as shown. (2x4 wood supports are
required to support the weight of the hood.)
Ŷ Arrange cross framing in the ceiling to suit the
existing structure.
Ŷ Your ceiling joists will be like one of the following
examples.
INSTALLATION INSTRUCTIONS
Installation Preparation
Ceiling
Hood ducting
centerline
Cooktop
Countertop
´
Side view
Align with
center of
cooktop ´
´
Duct covers
Top view – ceiling joists parallel to front of hood
16” Joist
spacing
´ ´'XFW
Front
of
hood
2x4 Cross framing
wood supports
Cooktop
outline
Align duct to center of
cooktop
EXAMPLE A
Install cross-framing symmetrically over
GXFWFRRNWRSFHQWHUOLQH
´
14 49-7000198 Rev. 0
CONSTRUCT CEILING SUPPORT (Cont.)
Installation Preparation
INSTALLATION INSTRUCTIONS
Top view – ceiling joists run perpendicular to front of hood
16” Joist
spacing
´ ´'XFW
Front of
hood
Cooktop
outline
Align duct
to center
of cooktop
EXAMPLE B
´
Install cross-framing
V\PPHWULFDOO\RYHUGXFWFRRNWRS
centerline
2x4 Cross
framing wood
supports
Top view – ceiling joists at angle to front of hood
16” Joist
spacing
´'XFW
Cooktop
outline
Align duct
to center
of cooktop
EXAMPLE C
Front
of
hood
2x4 Cross
framing wood
supports
Install cross-framing symmetrically over
GXFWFRRNWRSFHQWHUOLQH
´
´
49-7000198 Rev. 0 15
CONSTRUCT CEILING SUPPORT (Cont.)
Ŷ Secure each 2 x 4 block with at least four (4), #10
ZRRGVFUHZV´ORQJQRWVXSSOLHG8VHZRRG
screws total for the two supports.
Ŷ The cross framing must be accurately aligned
to assure correct positioning of the hood.
Ŷ The cross framing must be level in all directions.
Check with a spirit level and adjust if necessary.
IMPORTANT: The ceiling structure must be capable
of supporting the weight of the hood (approximately
200 pounds) and any inadvertent user contact loads.
The hood support frame will be supported by the
2 x 4 cross framing.
Ductwork for Installations Vented to the Outdoors
Ŷ Use the shortest and straightest duct route for
satisfactory performance.
Ŷ7KLVYHQWKRRGPXVWXVH´URXQGULJLGGXFW
Ŷ,QVWDOOWKHKRXVHGXFWZRUNWRUXQKRUL]RQWDOO\
between ceiling joists or straight up through
the roof.
Finish the Ceiling
Ŷ)LQLVKWKHFHLOLQJVXUIDFH%HVXUHWRPDUNORFDWLRQ
of the ceiling joists and cross framing. Check to be
VXUHWKHFHLOLQJLVOHYHOXVHVKLPVLIQHFHVVDU\
INSTALLATION INSTRUCTIONS
Installation Preparation
2 x 4 min.
Cross framing
Ceiling
joist
´ ´
´
Duct
Ceiling joist
2 x 4
Vent straight up through
the ceiling
16 49-7000198 Rev. 0
Installation Instructions
INSTALLATION INSTRUCTIONS
INSTALLATION - VENTED TO THE OUTSIDE
STEP 1: MOUNT TEMPLATE
Ŷ Align the template with the marks on the ceiling
and tape in place.
Be sure the template is oriented correctly with
the front of the hood.
Ŷ Use a plumb bob to be sure the mounting holes
will provide parallel alignment with the countertop
below.
Ŷ Determine wire access hole location.
Ŷ Center punch all screw and determined wire hole
locations.
Ŷ Drill pilot holes in the 4 screw locations. Use a
´ELWDQGGULOODSSUR[LPDWHO\´GHHS
Ŷ'ULOORQH´KROHIRUZLUHV
Ŷ&XWWKH´GXFWRSHQLQJWKURXJKWKHFHLOLQJ
STEP 2: INSTALL CEILING SUPPORT
Ŷ Using 4 wood screws provided, attach the ceiling
support to the ceiling over duct opening hole
using pilot holes drilled in step 1.
Screws
Front
36" HOOD
TEMPLATE
Cut one 1/2" Dia.
Wire Access Hole
as Needed
8-1/4" To
Centerline of
Pilot Holes
8-1/2"
FRONT OF HOOD
Cut one 1/2" Dia.
Wire Access Hole
as Needed
Cut one 1/2" Dia.
Wire Access Hole
as Needed
Cut one 1/2" Dia.
Wire Access Hole
as Needed
Drill 3/16" Pilot Holes
Approx. 1-1/2" Deep
4 Places
8-1/4" To
Centerline of
Pilot Holes
10-5/16" To
Centerline of
Pilot Holes
10-5/16" To
Centerline of
Pilot Holes
31-14772
Printed in Mexico 12-08 JR
STEP 3: INSTALL LOWER
HORIZONTAL SUPPORTS TO HOOD
ASSEMBLY
Install the lower horizontal support to 4 lower vertical
VXSSRUWVZLWK[PPVFUHZV
A. Lower horizontal support
%[PPVFUHZV
C. 4 - Lower vertical supports
A
B
C
NOTE: Only for recirculating version, air deflector
not included.
INSTALL AIR DEFLECTOR INTO CEILING
SUPPORT
Ŷ Lay ceiling support on a firm surface.
Ŷ Position the air deflector
onto the ceiling support,
duct opening up and one
of the open sides to what
will be the front of the
hood assembly. The tabs
on the deflector will be to
the outside of the ceiling
support.
Ŷ8VLQJVFUHZVSURYLGHGVHFXUHWKHWDEVRQWKH
deflector to the ceiling support.
49-7000198 Rev. 0 17
Installation Instructions
INSTALLATION - VENTED TO THE OUTSIDE (Cont.)
INSTALLATION INSTRUCTIONS
STEP 4: INSTALL UPPER VERTICAL
SUPPORTS TO HOOD ASSEMBLY
Install 4 upper vertical supports to the lower
KRUL]RQWDOVXSSRUWZLWK[PPVFUHZV
A. 4 - Upper vertical supports
%[PPVFUHZV
C. Lower horizontal support
A
C
B
STEP 5: INSTALL TO UPPER SUPPORT
• Install the structure to the upper horizontal support
ZLWK[PPVFUHZV
NOTE: Attach the structure to the previously installed
upper horizontal support.
A. Upper horizontal support
%[PPVFUHZV
B.
A
B
STEP 6: INSTALL HOOD ASSEMBLY
TO SUPPORT
Using 2 or more people, lift the range hood
assembly under the structure.
A. Lower vertical supports
B. Range hood assembly
STEP 7: INSTALL TO LOWER SUPPORT
• Attach the range hood assembly to the lower vertical
supports with 2 leveling screws and 2 nuts.
A. 2 - Leveling screws
B. Lower vertical support
C. Place leveling screws through the
structure
B
A
A
B
C
 49-7000198 Rev. 0
Installation Instructions
INSTALLATION INSTRUCTIONS
INSTALLATION - VENTED TO THE OUTSIDE (Cont.)
STEP 9: CONNECT ELECTRICAL
Verify that power is turned off at the source.
WARNING If house wiring is not 2-wire with
a ground wire, a ground must be provided by the
installer. When house wiring is aluminum, be sure
to use U.L. approved anti-oxidant compound and
aluminum-to-copper connectors.
Ŷ5HPRYHWKHVFUHZVRQWKHMXQFWLRQER[FRYHU
and the knockout on the top left side.
Ŷ6HFXUHWKHKRXVHZLULQJWRWKHMXQFWLRQER[ZLWKD
strain relief (not provided).
ŶConnect the white lead to the branch circuit
white lead.
Ŷ&RQQHFWWKHEODFNOHDGWRWKHEUDQFKFLUFXLWEODFN
lead.
Ŷ&RQQHFWWKHJUHHQ\HOORZOHDGWRWKHEUDQFK
circuit green lead or bare ground lead.
Ŷ6HFXUHDOOWKHFRQQHFWLRQVZLWKZLUHQXWVRQHDFK
electrical connector.
Ŷ3XVKWKHZLUHVLQWRWKHMXQFWLRQER[DQGUHSODFH
the cover. Be sure the wires are not pinched.
Ŷ6HFXUHWKHMXQFWLRQER[FRYHUZLWKWKHRULJLQDO
screws.
Junction
box cover
Knockout
STEP 8: INSTALL VERTICAL
SUPPORTS
,QVWDOOWKHYHUWLFDOVXSSRUWVZWLK[PP
screws. Make sure all screws are securely tightened.
A. 4 - Lower vertical supports
%[PPVFUHZV
A
B
49-7000198 Rev. 0 19
Installation Instructions
INSTALLATION - VENTED TO THE OUTSIDE (Cont.)
INSTALLATION INSTRUCTIONS
STEP 10: INSTALL DUCT COVER
SUPPORTS
Ŷ$WWDFKWKHGXFWFRYHUVXSSRUWVWRWKHVLGHVRIWKH
horizontal and ceiling supports using 4 screws
per duct cover support.
Screws
Ceiling
support
Horizontal
support
Duct cover
support
STEP 11: INSTALL DUCT COVERS
IMPORTANT: Two people are required to install the
duct covers.
NOTE: If you are installing this hood for
recirculating operation, place the duct covers onto
the hood with the venting slots at the top. If the
hood is vented to the outside, the holes should be
positioned on the bottom.
Ŷ5HPRYHWKHSURWHFWLYHILOPIURPDOOGXFWFRYHUV
Ŷ3ODFHRQHXSSHUGXFWFRYHURYHUWKHUHDURIWKH
support assembly. The tabs on the edges of the
duct cover will slide into a notch on the duct cover
support. When all 6 tabs on the duct cover are in
the notches on both of the duct cover supports,
slide the duct cover up so it sits on the duct cover
support spring clip.
Ŷ3ODFHDGXFW
cover clip onto the
bottom of the rear
lower duct cover
locking the clip into
place. Repeat on
the other side.
Ŷ/RZHUWKHGXFW
cover into the
recess on the hood, being careful to hold the clip
in place while lowering the duct cover onto the
hood assembly.
Ŷ3ODFHWKHIURQWORZHUGXFWFRYHULQWRWKHUHFHVVRI
the hood locking it onto the duct cover clip on the
rear cover.
Ŷ3ODFHDGXFWFRYHUFOLSDWWKHWRSRQHDFKVLGH
where the front and rear duct covers meet. This
will hold the rear and front covers together.
Left duct cover
Duct cover
support spring clip
Duct cover clip
20 49-7000198 Rev. 0
Installation Instructions
INSTALLATION INSTRUCTIONS
INSTALLATION - VENTED TO THE OUTSIDE (Cont.)
STEP 11: INSTALL DUCT COVERS
(Cont.)
Ŷ8VLQJVFUHZVSURYLGHGVHFXUHWKHORZHUGXFW
covers to the hood assembly from the underside
of the hood.
STEP 12: INSTALL METAL GREASE
FILTER
Ŷ5HPRYHSURWHFWLYHILOPRQWKHJUHDVHILOWHU
NOTE: The charcoal filter is not required for this
installation.
Ŷ)LWWKHWDEVDWWKHHQGRIWKHILOWHULQWRWKHVORWVLQ
left side of the filter opening. Lift up the right side
of the filter and push gently until the filter locks
into place. Make sure the filter lock is in the closed
position to secure the filter.
Ŷ7RUHPRYHWKHILOWHUSXOOGRZQZDUGRQWKHILOWHU
lock to release.
NOTE: Only for recirculating version, air deflector
not included.
INSTALL FILTER
Charcoal Filter
Insert the charcoal filter into the opening. Push the
latch on both sides toward the center and engage
the flange.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

GE Profile UVI7361SWSS Le manuel du propriétaire

Catégorie
Hottes
Taper
Le manuel du propriétaire