VTech CS5119-13 Manuel utilisateur

Marque: VTech

Modèle: CS5119-13

Catégorie: Téléphones

Taper: Manuel utilisateur

CS5119

CS5119-13

CS5119-15

CS5119-16

CS5119-2

Abridged user’s manual

Scan the QR code for

support information

When using your telephone equipment, basic safety

precautions should always be followed to reduce the risk of

ﬁre, electric shock and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the

product.

3. Unplug this product from the wall outlet before cleaning.

Do not use liquid or aerosol cleaners. Use a damp cloth

for cleaning.

4. CAUTION: Do not install the telephone base at a height

above 2 meters.

5. Do not use this product near water such as near a bath tub,

wash bowl, kitchen sink, laundry tub or a swimming pool,

or in a wet basement or shower.

6. Do not place this product on an unstable table, shelf,

stand or other unstable surfaces.

7. Avoid placing the telephone system in places with extreme

temperature, direct sunlight, or other electrical devices.

Protect your phone from moisture, dust, corrosive liquids

and fumes.

8. Slots and openings in the back or bottom of the telephone

base and handset are provided for ventilation. To protect

them from overheating, these openings must not be

blocked by placing the product on a soft surface such as

a bed, sofa or rug. This product should never be placed

near or over a radiator or heat register. This product should

not be placed in any area where proper ventilation is not

provided.

9. This product should be operated only from the type of

power source indicated on the marking label. If you are

not sure of the type of power supply in your home or

ofﬁce, consult your dealer or local power company.

10. Do not allow anything to rest on the power cord. Do not

install this product where the cord may be walked on.

11. Never push objects of any kind into this product through

the slots in the telephone base or handset because they

may touch dangerous voltage points or create a short

circuit. Never spill liquid of any kind on the product.

12. To reduce the risk of electric shock, do not disassemble

this product, but take it to an authorized service facility.

Opening or removing parts of the telephone base or

handset other than speciﬁed access doors may expose

you to dangerous voltages or other risks. Incorrect

reassembling can cause electric shock when the product

is subsequently used.

13. Do not overload wall outlets and extension cords.

14. Unplug this product from the wall outlet and refer

servicing to an authorized service facility under the

following conditions:

• When the power supply cord or plug is damaged or

frayed.

• If liquid has been spilled onto the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operation instructions. Improper

adjustment of other controls may result in damage

and often requires extensive work by an authorized

technician to restore the product to normal operation.

• If the product has been dropped and the telephone

base and/or handset has been damaged.

• If the product exhibits a distinct change in performance.

15. Avoid using a telephone (other than cordless) during an

electrical storm. There is a remote risk of electric shock

from lightning.

16. Do not use the telephone to report a gas leak in the

vicinity of the leak. Under certain circumstances, a spark

may be created when the adapter is plugged into the

power outlet, or when the handset is replaced in its

cradle. This is a common event associated with the

closing of any electrical circuit. The user should not

plug the phone into a power outlet, and should not

put a charged handset into the cradle, if the phone is

located in an environment containing concentrations

of ﬂammable or ﬂame-supporting gases, unless there

is adequate ventilation. A spark in such an environment

could create a ﬁre or explosion. Such environments

might include: medical use of oxygen without adequate

ventilation; industrial gases (cleaning solvents; gasoline

vapors; etc.); a leak of natural gas; etc.

17. Only put the handset of your telephone next to your ear

when it is in normal talk mode.

18. The power adapter is intended to be correctly oriented

in a vertical or ﬂoor mount position. The prongs are not

designed to hold the plug in place if it is plugged into a

ceiling, under-the-table or cabinet outlet.

19. For pluggable equipment, the socket-outlet shall

be installed near the equipment and shall be easily

accessible.

20. CAUTION: Use only the batteries indicated

in this manual. There may be a risk of

explosion if a wrong type of battery is used for the

handset. Use only the supplied rechargeable batteries

or replacement batteries (BT262342) for the handset. Do

not dispose of batteries in a ﬁre. They may explode.

Disposed of used batteries according to the instruction.

• Do not use the battery in following conditions:

»High or low extreme temperature during use, storage

or transportation.

»Replacement of a battery with an incorrect type that can

defeat a safeguard.

»Disposal of a battery into ﬁre or a hot oven, or

mechanically crushing or cutting of a battery, that can

result in an explosion.

»Leaving a battery in an extremely high temperature

surrounding environment that can result in an explosion

or the leakage of ﬂammable liquid or gas.

»A battery subjected to extremely low air pressure that

can result in an explosion or the leakage of ﬂammable

liquid or gas.

21. Use only the adapter included with this product.

Incorrect adapter polarity or voltage can seriously

damage the product.

22. The applied nameplate is located at the bottom or near

of the product.

SAVE THESE INSTRUCTIONS

Battery

• Use only the battery provided or equivalent. To order

a replacement, visit our website at www.vtechphones.

com or call 1 (800) 595-9511. In Canada, go to phones.

vtechcanada.com or call 1 (800) 267-7377.

• Do not dispose of the battery in a ﬁre. Check with

local waste management codes for special disposal

instructions.

• Do not open or mutilate the battery. Released

electrolyte is corrosive and may cause burns or injury

to the eyes or skin. The electrolyte may be toxic if

swallowed.

• Exercise care in handling batteries in order not to create

a short circuit with conductive materials.

• Charge the battery provided with this product only

in accordance with the instructions and limitations

speciﬁed in this manual.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless

telephones):

Wireless Technology Research, LLC (WTR), an independent

research entity, led a multidisciplinary evaluation of the

interference between portable wireless telephones and

implanted cardiac pacemakers. Supported by the U.S. Food

and Drug Administration, WTR recommends to physicians

that:

Pacemaker patients

• Should keep wireless telephones at least six inches from

the pacemaker.

• Should NOT place wireless telephones directly over

the pacemaker, such as in a breast pocket, when it is

turned ON.

• Should use the wireless telephone at the ear opposite

the pacemaker.

WTR’s evaluation did not identify any risk to bystanders with

pacemakers from other persons using wireless telephones.

About cordless telephones

• Privacy: The same features that make a cordless

telephone convenient create some limitations.

Telephone calls are transmitted between the telephone

base and the cordless handset by radio waves, so

there is a possibility that the cordless telephone

conversations could be intercepted by radio receiving

equipment within range of the cordless handset. For

this reason, you should not think of cordless telephone

conversations as being as private as those on corded

telephones.

• Electrical power: The telephone base of this cordless

telephone must be connected to a working electrical

outlet. The electrical outlet should not be controlled by

a wall switch. Calls cannot be made from the cordless

handset if the telephone base is unplugged, switched

off or if the electrical power is interrupted.

• Potential TV interference: Some cordless telephones

operate at frequencies that may cause interference

to televisions and VCRs. To minimize or prevent such

interference, do not place the telephone base of the

cordless telephone near or on top of a TV or VCR.

If interference is experienced, moving the cordless

telephone farther away from the TV or VCR often

reduces or eliminates the interference.

• Rechargeable batteries: Exercise care in handling

batteries in order not to create a short circuit with

conducting material such as rings, bracelets and keys.

The battery or conductor may overheat and cause harm.

Observe proper polarity between the battery and the

battery charger.

• Nickel-metal hydride rechargeable batteries: Dispose

of these batteries in a safe manner. Do not burn or

puncture the battery. Like other batteries of this type,

if burned or punctured, they could release caustic

material which could cause injury.

Go to www.vtechphones.com (US) to register your

product for enhanced warranty support and latest

VTech product news.

Go to phones.vtechcanada.com (Canada) for the latest

VTech product news.

Speciﬁcations are subject to change without notice.

CS5119-X_56VCB_US-CAN_ACIB_V1.0_220708

HS56VCB-DCX81

What’s in the box

Your telephone package contains the following

items. Save your sales receipt and original packaging

in case it is necessary to ship your telephone for

warranty service.

Abridged

user’s

manual

1 set for CS5119-2

1 set for CS5119 |

CS5119-13 | CS5119-15

| CS5119-16

2 sets for CS5119-2

Install and Connect | Mount (optional)

Install the battery

THIS SIDE UP

Connect and charge

Connect the telephone base

If you subscribe to digital subscriber

line (DSL) high-speed Internet service

through your telephone line, make sure

you connect a DSL ﬁlter (not included)

to the telephone wall jack.

Mount (optional)

12 hrs

Setup Overview

After the telephone is installed or power returns

following a power outage and battery depletion, the

handset will prompt you to set the date and time.

Date and time

Follow the steps below to set the date and time. For

example, if the date is 25 January, 2022, and the time

is 11:07 AM:

When the

handset

prompts you

to set the date

and time

Date:MM/DD/YY

ECO

Date:01/2?/YY

ECO

1. Enter the date.

Date:01/25/22

ECO

Time: 1?:MM --

ECO

Time: 11:07 AM

ECO

2. Press

SELECT.

3. Enter the

time.

4. Press q/p to

select AM to

PM.

5. Press SELECT to save.

NOTE: If you have skipped the prompt, you

can set up again by pressing MENU. Scroll

to choose Set date/time and press SELECT.

Then, follow the steps above.

Change LCD language settings

You can select English, French, or Spanish to be used

in all screen displays:

HANDSET

ECO

11:07 1/25

Settings

ECO

1. Press MENU.2. Press q/p to scroll to

Settings, then press

SELECT.

LCD language

ECO

English

ECO

3. Press SELECT

to select LCD

language.

4. Press q/p to

choose your desired

language and press

SELECT.

NOTE: If you accidentally set the LCD

language to Spanish or French, press MENU

and then enter *364# to change the handset

LCD language back to English while the

handset is not in use.

Telephone base

1 –

• Page all system handsets.

2 – light

• Flashes when there is an incoming call, or

another telephone sharing the same line is in

use.

• On when the telephone is in use.

3 – Charging pole

Handset

1 – Handset earpiece

2 – LCD display

3 –

• Show the menu.

• While in a menu, press to select an item, or save

an entry or setting.

4 –

• Hang up a call.

• Return to the previous menu or exit menu

display without making changes.

• Delete digits while predialing.

• Silence the handset ringer temporarily while

the phone is ringing.

• Press and hold to erase the missed call indicator

while the handset is not in use.

5 –

• Press and hold to turn on or off the quiet mode.

• Show other dialing options when reviewing a

caller ID log entry.

6 –

• Press to start an intercom conversation or

transfer a call (for two-handset model only).

7 – Microphone

8 –

• Mute the microphone during a call.

• Silence the handset ringer temporarily while

the phone is ringing.

• Delete the displayed entry while reviewing the

phonebook, caller ID log, call block list or redial list.

• Delete digits or characters when entering

numbers or names.

9 –

• Make or answer a call using the handset

speakerphone.

• During a call, press to switch between the

speakerphone and the handset earpiece.

10 –

• Switch to tone dialing temporarily during a

call.

11 –

• Press to add a space when entering names.

12 –

• Press repeatedly to add or remove 1 in front of

the caller ID log entry before dialing or saving

it to the phonebook.

• Press and hold to set or dial your voicemail

number.

13 –

• Make or answer a call.

• Answer an incoming call when you receive a

call waiting alert.

14 –

• Review the redial list.

• Insert a dialing pause while dialing or entering

numbers into the phonebook.

15 –

• Review the phonebook when the phone is not

in use.

• Scroll up while in a menu, or in the

phonebook, caller ID log, call block list or

redial list.

• Move the cursor to the right when entering

numbers or names.

• Increase the listening volume during a call.

• Review the caller ID log when the telephone

is not in use.

• Scroll down while in a menu, or in the

phonebook, caller ID log, call block list or

redial list.

• Move the cursor to the left when entering

numbers or names.

• Decrease the listening volume during a call.

16 – light

• On when the handset is charging.

Charger

1 – Charging pole

Display icons

The battery icon flashes when

the battery is low and needs

charging.

The battery icon animates when

the battery is charging.

The battery icon becomes

solid when the battery is fully

charged.

The handset ringer is turned off.

There are new voicemail

received from your telephone

service provider.

NEW New caller ID log entry.

ECO The ECO mode activates

automatically to reduce power

consumption when the handset

is within range from the

telephone base.

Use the handset menu

1. Press MENU when the phone is not in use.

2. Press q or p until the screen displays the

desired feature menu.

3. Press SELECT.

• To return to the previous menu, press CANCEL.

• To exit menu display, press and hold CANCEL.

Make a call

• Press or , and then dial the telephone

number.

Answer a call

• Press , or any of the dialing keys.

End a call

• Press OFF or put the handset back in the

telephone base or charger.

Speakerphone

• During a call, press on the handset to

switch between speakerphone and handset

earpiece.

Volume

• During a call, press p/VOLUME/q to adjust

the listening volume.

Mute

The mute function allows you to hear the other party

but the other party cannot hear you.

1. During a call, press MUTE. The handset

displays Muted.

2. Press MUTE again to resume the conversation.

The handset displays Microphone on brieﬂy.

Telephone operations

Join a call in progress (for two-handset

models only)

You can use up to two handsets at a time on an

outside call.

• When a handset is already on a call, press

or on another handset to join the call.

• To exit the call, press OFF on the handset or

place it in the telephone base or charger. The

call continues until all handsets hang up.

Call waiting

When you subscribe to call waiting service from

your telephone service provider, you hear an

alert tone if there is an incoming call while you are

already on a call.

• Press FLASH to put the current call on hold and

take the new call.

• Press FLASH at any time to switch back and

forth between calls.

Find handset

Use this feature to ﬁnd the system handset.

To start paging:

• Press FIND HANDSET on the telephone base

when not in use. All idle handsets ring and

display ** Paging **.

To end paging:

• Press FIND HANDSET at the telephone base.

-OR-

• Press , , OFF or any of the dialing keys on

the handset.

-OR-

• Place the handset in the telephone base or

charger.

NOTE: Do not press and hold FIND HANDSET

for more than 4 seconds. It may lead to handset

deregistration.

Redial list

Each handset stores the last 10 telephone numbers

dialed. When there are already 10 entries, the

oldest entry is deleted to make room for the new

entry.

Review and dial a redial list entry

1. Press REDIAL when the handset is not in use.

2. Press q, p or REDIAL repeatedly until the

desired entry displays.

3. Press to dial.

Delete a redial list entry

• When the desired redial entry displays, press

DELETE.

Intercom

Use the intercom features for conversations

between two handsets.

1. Press INT on your handset when not in use. Use

the dialing keys to enter a destination handset

number if necessary.

2. To answer the intercom call, press , , INT

or any dialing key on the destination handset.

3. To end the intercom call, press OFF or place the

handset back in the telephone base or charger.

Answer an incoming call during an intercom

call

If you receive an incoming call during an intercom

call, there is an alert tone.

• To answer the outside call, press . The

intercom call ends automatically.

• To end the intercom call without answering

the outside call, press OFF. The telephone

continues to ring.

Transfer a call

While on an outside call, you can use the intercom

feature to transfer the call from one handset to

another.

1. Press INT on your handset during a call. The

current call is put on hold. Use the dialing

keys to enter a destination handset number if

necessary.

2. To answer the intercom call, press , , or

any dialing key on the destination handset. You

can now have a private conservation before

transferring the call.

3. Press OFF on your originating handset, or place

it back in the telephone base or charger. Your

originating handset displays Line in use. The

destination handset is then connected to the

outside call.

Phonebook

The phonebook can store up to 50 entries, which

are shared by all handsets. Each entry may consist

of a telephone number up to 30 digits, and a name

up to 15 characters.

Add a phonebook entry

1. Enter the number when the phone is not in use.

Press MENU, then go to Step 3.

-OR-

Press MENU when the phone is not in use, then

press SELECT to choose Phonebook. Press

SELECT again to choose Add new entry.

2. Use the dialing keys to enter the number.

-OR-

Copy a number from the redial list by pressing

REDIAL and then press q, p or REDIAL

repeatedly to select a number. Press SELECT to

copy the number.

3. Press SELECT to move on to enter the name.

4. Use the dialing keys to enter the name.

Additional key presses show other characters of

that particular key.

5. Press SELECT to save.

While entering names and numbers, you can:

• Press DELETE to backspace and erase a digit or

character.

• Press and hold DELETE to erase the entire entry.

• Press q or p to move the cursor to the left or

right.

• Press and hold PAUSE to insert a dialing pause

(for entering numbers only).

• Press 0 to add a space (for entering names only).

Review a phonebook entry

Entries are sorted alphabetically.

1. Press when the phone is not in use.

2. Scroll to browse through the phonebook, or use

the dialing keys to start a name search.

Delete a phonebook entry

1. When the desired entry displays, press DELETE.

2. When the handset displays Delete entry?, press

SELECT.

Edit a phonebook entry

1. When the desired entry displays, press SELECT.

2. Use the dialing keys to edit the number, then

press SELECT.

3. Use the dialing keys to edit the name, then

press SELECT.

Dial a phonebook entry

• When the desired entry appears, press or

to dial.

(US)

(CA)

Important safety instructions

Caller ID

If you subscribe to caller ID service, information

about each caller appears after the ﬁrst or

second ring. If you answer a call before the caller

information appears on the screen, it will not be

saved in the caller ID log.

The caller ID log stores up to 30 entries. Each entry

has up to 24 digits for the phone number and 15

characters for the name.

If the telephone number has more that 15 digits,

only the last 15 digits appear. If the name has more

than 15 characters, only the ﬁrst 15 characters are

shown and saved in the caller ID log.

Review a caller ID log entry

1. Press CID when the phone is not in use.

2. Scroll to browse through the caller ID log.

Missed call indicator

When there are calls that have not been reviewed

in the caller ID log, the handset displays XX missed

calls.

Each time you review a caller ID log entry marked

NEW, the number of missed calls decreases by

one.

When you have reviewed all the missed calls, the

missed call indicator no longer displays.

If you do not want to review the missed calls

one by one, press and hold CANCEL on the idle

handset to erase the missed call indicator. All the

entries are then considered old.

Dial a caller ID log entry

• When the desired entry appears, press or

to dial.

Save a caller ID log entry to the phonebook

1. When the desired caller ID log entry displays,

press SELECT.

2. Press SELECT to choose To Phonebook.

3. Use the dialing keys to edit the number, if

necessary. Then press SELECT.

4. Use the dialing keys to edit the name, if

necessary. Then press SELECT.

Delete the caller ID log entries

• When the desired caller ID log entry displays,

press DELETE.

To delete all caller ID log entries:

1. Press MENU when the phone is not in use.

2. Scroll to Caller ID log and then press SELECT.

3. Scroll to Delete all and then press SELECT twice.

Call block

If you have subscribed to caller ID service, you

can set the telephone to block unknown calls and

certain undesired calls. The call block list can store

up to 20 entries.

Block unknown calls

1. Press MENU when the handset is not in use.

2. Scroll to Call block, and then press SELECT.

3. Scroll to choose Calls w/o num, and then press

SELECT.

4. Scroll to choose Unblock or Block, and then

press SELECT to save.

Add a call block list entry

1. Press MENU when the handset is not in use.

2. Scroll to Call block, and then press SELECT.

3. Press SELECT to choose Block list.

4. Scroll to choose Add new entry, and then press

SELECT.

5. Use the dialing keys to enter the number (up to

30 digits).

6. Press SELECT to move to enter the name.

7. Use the dialing keys to enter the name (up to 15

characters). Additional key presses show other

characters of that particular key.

8. Press SELECT to save.

Review call block list

1. Press MENU when the handset is not in use.

2. Scroll to Call block, and then press SELECT.

3. Press SELECT to choose Block list.

4. Press SELECT to choose Review.

Edit a call block list entry

1. When the desired entry displays, press SELECT.

2. Use the dialing keys to edit the number (up to

30 digits), and then press SELECT.

3. Use the dialing keys to edit the name (up to 15

characters), and then press SELECT to save.

Save a caller ID log entry to call block list

1. When the desired caller ID log entry displays,

press SELECT.

2. Scroll to To Call block, and then press SELECT.

3. Use the dialing keys to edit the number, if

necessary. Then press SELECT.

4. Use the dialing keys to edit the name, if

necessary. Then press SELECT to save.

Delete a call block list entry

• When the desired call block list entry displays,

press DELETE.

Mute ﬁrst rings

An incoming call will ring once and then the

system will check if the call should be blocked. You

can choose to mute the ﬁrst ring for all incoming

calls, so that there will be no ring for blocked calls.

By default, the ﬁrst ring is set to On.

1. Press MENU when the handset is not in use.

2. Press 7464# on the handset.

3. Scroll to choose First ring:On or First ring: Off,

and then press SELECT to save.

Sound settings

Key tone

You can turn the key tone on or off.

1. Press MENU when the handset is not in use.

2. Scroll to Settings and then press SELECT.

3. Scroll to choose Key tone, then press SELECT.

4. Press q or p to choose On or Off, then press

SELECT to save.

Ringer tone

You can choose from different ringer tones for

each handset.

1. Press MENU when the handset is not in use.

2. Scroll to Ringers and then press SELECT.

3. Scroll to choose Ringer tone, then press

SELECT.

4. Press q or p to sample each ringer tone, then

press SELECT to save.

NOTE: If you turn off the ringer volume,

you will not hear ringer tone samples.

Ringer volume

You can adjust the handset ringer volume level, or

turn the ringer off.

1. Press MENU when the handset is not in use.

2. Scroll to Ringers and then press SELECT twice.

3. Press q or p to sample each volume level,

then press SELECT to save.

NOTE: When the ringer volume is set to

Off, the handset still rings when you press

FIND HANDSET at the telephone base.

Temporary ringer silencing

When the telephone is ringing, you can temporarily

silence the ringer without disconnecting the call. The

next call rings normally at the preset volume.

To silence the handset ringer:

• Press CANCEL or MUTE. The handset displays

Ringer muted and .

Quiet mode

You can turn on the quiet mode for a period of

time. During this period, all tones (except paging

tone) are muted.

1. Press and hold on the handset when it

is not in use.

2. Use the dialing keys to enter the duration, and

then press SELECT to save.

• To turn off the quiet mode, press and hold

on the handset when it is not in use.

Retrieve voicemail from

telephone service

Voicemail is a feature available from most

telephone service providers. It may be included

with your telephone service, or may be optional.

Fees may apply.

Retrieve voicemail

When you received a voicemail, the handset

displays and New voicemail. To retrieve, you

typically dial an access number provided by your

telephone service provider, and then enter a security

code. Contact your telephone service provider

for instructions on how to conﬁgure the voicemail

settings and listen to messages.

NOTE: After you have listened to all new

voicemail messages, the indicators on the

handset turn off automatically.

Set your voicemail number

You can save your access number on each handset

for easy access to your voicemail.

After you saved the voicemail number, you can

press and hold to retrieve voicemail.

1. Press MENU when the phone is not in use.

2. Scroll to Settings and then press SELECT.

3. Scroll to Voicemail # and then press SELECT.

4. Use the dialing keys to enter the voicemail

number (up to 30 digits).

5. Press SELECT to save.

Turn off the new voicemail indicators

If you have retrieved your voicemail while away

from home, and the handset still displays the new

voicemail indicators, use this feature to turn off the

indicators.

NOTE: This feature turns off the indicators

only, it does not delete your voicemail

messages.

1. Press MENU when the phone is not in use.

2. Scroll to Settings and then press SELECT.

3. Scroll to Clr voicemail and then press SELECT.

ECO mode

This power conserving technology reduces power

consumption for optimal battery performance. The

ECO mode activates automatically whenever the

handset is synchronized with the telephone base.

General product care

Taking care of your telephone

Your cordless telephone contains sophisticated

electronic parts, so it must be treated with care.

Avoid rough treatment

Place the handset down gently. Save the original

packing materials to protect your telephone if you

ever need to ship it.

Avoid water

Your telephone can be damaged if it gets wet. Do

not use the handset outdoors in the rain, or handle

it with wet hands. Do not install the telephone

base near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power

surges harmful to electronic equipment. For your

own safety, take caution when using electrical

appliances during storms.

Cleaning your telephone

Your telephone has a durable plastic casing that

should retain its luster for many years. Clean it

only with a dry non-abrasive cloth. Do not use

dampened cloth or cleaning solvents of any kind.

Need help?

For operations and guides to help you using your

telephone, and for the latest information and

supports, go and check the online help topics and

online FAQs.

Use your smartphone or mobile device to access our

online help.

• Go to https://help.vtechphones.com/cs5119 (US);

OR https://phones.vtechcanada.com/en/support/

general/manuals?model=cs5119 (Canada)

• Scan the QR code on the right. Launch the camera

app or QR code scanner app on

your smartphon e or tablet.

Hold the device’s camera up to

the QR code and frame it. Tap

the notiﬁcation to trigger the

redirection of the online help.

- If the QR code is not clearly

displayed, adjust your camera’s

focus by moving your device

closer or further away until it is

clear.

You can also call our Customer

Support at 1 (800) 595-9511

[in US] or 1 (800) 267-7377 [in

Canada] for help.

For C-UL compliance only

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de blessures

corporelles ou d’électrocution, suivez toujours ces mesures

préventives de base lorsque vous utilisez votre téléphone :

1. Lisez et comprenez bien toutes les instructions.

2. Observez toutes les instructions et mises en garde inscrites

sur l’appareil.

3. Débranchez ce téléphone de la prise murale avant de le

nettoyer. N’utilisez pas de nettoyeurs liquides ni en aérosol.

N’utilisez qu’un chiffon doux et légèrement humecté.

4. ATTENTION: Ne pas installer le socle téléphonique à une

hauteur supérieure à 2 mètres.

5. N’utilisez pas ce produit près de l’eau, tel que près d’un

bain, d’un lavabo, d’un évier de cuisine, d’un bac de lavage

ou d’une piscine, ou dans un sous-sol humide ou sous la

douche.

6. Ne déposez pas ce téléphone sur un chariot, support

ou table chancelants. L’appareil pourrait tomber et être

sérieusement endommagé.

7. Évitez d’installer le système téléphonique dans les endroits

soumis à une température extrême, à la lumière directe

du soleil ou à proximité immédiate d’autres appareils

électriques ou électroniques. Protégez votre téléphone

contre les sources d’humidité, la poussière, les vapeurs et

les liquides corrosifs.

8. Le boîtier de l’appareil est doté de fentes et d’ouvertures

d’aération situées à l’arrière ou en dessous. Aﬁn

d’empêcher la surchauffe, ces ouvertures ne doivent

pas être obstruées en plaçant l’appareil sur un lit, divan,

tapis ou autre surface similaires. Ne placez pas cet

appareil à proximité d’un élément de chauffage ni d’une

plinthe électrique. De plus, ne l’installez pas dans une

unité murale ou un cabinet fermé qui ne possède pas

d’aération adéquate.

9. Ne faites fonctionner cet appareil qu’avec le type

d’alimentation indiqué sur les étiquettes de l’appareil.

Si vous ne connaissez pas le voltage de votre maison,

consultez votre marchand ou votre fournisseur d’électricité.

10. Ne déposez rien sur le cordon d’alimentation. Installez cet

appareil dans un endroit sécuritaire, là où personne ne

pourra trébucher sur la ligne d’alimentation ni le cordon

téléphonique modulaire.

11. N’insérez jamais d’objets à travers les fentes et ouvertures

de cet appareil, car ils pourraient toucher à des points

de tension dangereux ou court-circuiter des pièces, ce

qui constituerait un risque d’incendie ou d’électrocution.

N’échappez pas de liquides dans l’appareil.

12. Aﬁn de réduire les risques d’électrocution, ne démontez

pas l’appareil, mais apportez-le plutôt à un centre de

service qualiﬁé s’il doit être réparé. En enlevant le

couvercle, vous vous exposez à des tensions dangereuses

ou autres dangers similaires. Un remontage inadéquat

peut être à l’origine d’une électrocution lors d’une

utilisation ultérieure de l’appareil. Débranchez l’appareil

avant de procéder au nettoyage. Utilisez un chiffon

humide et doux.

13. Ne surchargez pas les prises de courant et les rallonges.

14. Débranchez cet appareil de la prise de courant et

communiquez avec le département de service à la clientèle

de VTech dans les cas suivants :

• Lorsque le cordon d’alimentation est endommagé ou

écorché.

• Si du liquide a été échappé dans l’appareil.

• Si l’appareil a été exposé à une source d’humidité telle

que la pluie ou l’eau.

• Si le produit ne fonctionne pas normalement en

respectant les instructions de fonctionnement. Réglez

uniquement les commandes indiquées dans le les

instructions de fonctionnement. Les réglages incorrects

des autres commandes pourraient provoquer un

dommage qui pourrait exiger un travail exhaustif

de la part d’un technicien autorisé aﬁn de rétablir le

fonctionnement normal de l’appareil.

• Si le produit a été échappé et que le socle et/ou le

combiné a été endommagé.

• Si le produit afﬁche une nette diminution de sa

performance.

15. Évitez d’utiliser un téléphone (autre qu’un sans ﬁl) pendant

un orage. Les éclairs peuvent être à l’origine d’une

électrocution.

16. N’utilisez pas le téléphone pour rapporter une fuite de

gaz à proximité de la fuite. En certaines circonstances, une

ﬂammèche pourrait être provoquée lorsque l’adaptateur

est branché à une prise de courant, ou lorsque le

combiné est déposé sur le socle. Ceci est un événement

commun associé à la fermeture d’un circuit électrique.

L’utilisateur ne devrait pas brancher le téléphone à une

prise de courant, et ne devrait pas déposer le combiné

chargé sur le socle, si le téléphone se trouve à proximité

d’un endroit comportant des concentrations de gaz

inﬂammables, à moins que la ventilation soit adéquate.

Une ﬂammèche dans un tel endroit pourrait provoquer

un incendie ou une explosion. De tels environnements

peuvent comprendre: des endroits où l’on utilise de

l’oxygène médical sans ventilation adéquate; des gaz

industriels (dissolvants de nettoyage, des vapeurs

d’essence, etc.); une fuite de gaz naturel, etc.

17. Ne placez que le combiné de votre téléphone près de

votre oreille lorsqu’en mode de conversation.

18. Ces adaptateurs ont été conçus pour être orientés en

position verticale ou montés au sol. Les broches ne sont

pas conçues pour maintenir l’adaptateur en place si celui-ci

est barnché dans une prise au plafond ou sous une table/

armoire.

19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le

socle de prise de courant doit etre installe a proximite du

materiel et doit etre aisement accessible.

20. MISE EN GARDE: Il peut y avoir un risque

d’explosion si vous utilisez le mauvais type de piles pour

le téléphone. N’utilisez que les piles rechargeable inclus

ou les piles de rechange (BT262342). N’incinérez pas les

piles. Celles-ci risqueraient d’exploser. Mettre au rebut les

batteries usagées conformément aux instructions du

fabricant. Débrancher les lignes téléphoniques avant le

remplacement des piles.

• Évite d’utiliser la batterie dans les conditions suivantes:

• des températures extrêmes faibles ou élevées

auxquelles une batterie peut être soumise

pendant l’utilisation, le stockage ou le transport.

• remplacement d’une batterie par un type

incorrect pouvant supprimer une protection.

• mise au rebut d’une batterie dans un feu ou dans

un four chaud, ou écrasement mécanique ou

coupure d’une batterie, susceptible de provoquer

une explosion.

• maintien d’une batterie dans un environnement

à très haute température pouvant provoquer

une explosion ou la fuite de liquide ou de gaz

inﬂammables.

• batterie soumise à une pression de l’air

extrêmement faible pouvant provoquer une

explosion ou la fuite de liquide ou de gaz

inﬂammables.

21. N’utilisez que les adaptateurs inclus avec ce produit.

L’utilisation d’un adaptateur dont la polarité ou la tension

serait inadéquate risque d’endommager sérieusement le

produit et mettre votre sécurité en péril.

22. La plaque signalétique appliquée est située au bas ou à

proximité du produit.

CONSERVEZ CES INSTRUCTIONS

Pile

• N’utilisez que la pile incluse ou l’équivalent.

• Ne jetez pas la pile au feu. Vériﬁez les instructions

spéciﬁques de mise aux rebus auprès des autorités

locales.

• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en

échapperait est corrosif et pourrait causer des brûlures

ou des blessures aux yeux ou à la peau. L’électrolyte est

toxique si avalé.

• Soyez prudents lorsque vous manipulez les piles aﬁn

d’éviter les courts-circuits provoqués par des matériaux

conducteurs.

• Rechargez la pile incluse avec cet appareil, selon les

instructions et limites spéciﬁées dans ce guide d’utilisation.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (s’applique uniquement aux

téléphones numériques sans ﬁl) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une

ﬁrme de recherche indépendante, a mené une évaluation

pluridisciplinaire des interférences entre les téléphones sans

ﬁl portatifs et les stimulateurs cardiaques implantés dans

l’organisme. Appuyée par l’Administration des aliments et

drogues (FDA) des États-Unis, la ﬁrme WTR recommande aux

médecins :

Avis aux détenteurs de stimulateurs cardiaques

• Ils doivent tenir le téléphone sans ﬁl à une distance d’au

moins six pouces du stimulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl directement

sur le stimulateur cardiaque, tel que dans une poche de

chemise, lorsque celui-ci est en marche.

• Ils doivent utiliser le téléphone sans ﬁl en l’appuyant

sur l’oreille qui se trouve dans la direction opposée au

stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé de

risque pour les détenteurs de simulateurs cardiaques causés

par les gens qui utilisent un téléphone sans ﬁl à proximité de

ceux-ci.

À propos des téléphones sans ﬁl

Conﬁdentialité : Les mêmes caractéristiques qui constituent

des avantages pour les téléphones sans ﬁl afﬁchent

également des restrictions. Les appels téléphoniques

sont transmis entre le combiné sans ﬁl et le socle par

le biais d’ondes radio ; il y a donc la possibilité que vos

conversations téléphoniques sans ﬁl soient interceptées par

des équipements de réception radio se trouvant dans la

portée du combiné sans ﬁl. Pour cette raison, vous ne devez

pas percevoir les communications téléphoniques sans ﬁl

comme étant aussi conﬁdentielles que celles des téléphones

à cordons.

Alimentation électrique : Le socle de ce téléphone sans ﬁl

doit être branché à une prise électrique fonctionnelle. La

prise électrique ne doit pas être contrôlée par un interrupteur

mural. Les appels ne pourront pas être effectués du combiné

sans ﬁl si le socle est débranché ou mis hors tension ou si le

courant est coupé.

Possibilité d’interférences aux téléviseurs : Certains

téléphones sans ﬁl fonctionnent sur des fréquences

pouvant causer des interférences aux téléviseurs et aux

magnétoscopes. Pour réduire ou prévenir de telles

interférences, ne placez pas le socle du téléphone sans ﬁl près

ou sur un téléviseur ou magnétoscope. S’il y a présence de

parasites, il est conseillé d’éloigner le téléphone sans ﬁl du

téléviseur ou du magnétoscope aﬁn de réduire possiblement

les interférences.

Piles rechargeables : Manipulez les piles avec soin aﬁn de

ne pas les court-circuiter avec des bagues, bracelets ou clés.

Les piles ou le conducteur peut surchauffer et causer des

blessures. Respectez la polarité adéquate entre la pile et le

chargeur.

Les bloc-piles rechargeables à l’hydrure métallique de nickel

: Jetez ces blocs-piles de manière écologique et sécuritaire.

Ne les incinérez pas et ne les percez pas. Tel que les autres

piles de ce type, elles pourraient dégager une matière

toxique qui peut causer

des blessures corporelles si elles sont brûlées ou percées.

The RBRC SEAL

The RBRC seal on the nickel-metal hydride

battery indicates that VTech Communications,

Inc. is voluntarily participating in an industry

program to collect and recycle these batteries

at the end of their useful lives, when taken out

of service within the United States and Canada.

The RBRC program provides a convenient

alternative to placing used nickel-metal hydride batteries into

the trash or municipal waste, which may be illegal in your area.

VTech’s participation in RBRC makes it easy for you to drop

off the spent battery at local retailers participating in the RBRC

program or at authorized VTech product service centers. Please

call

1 (800) 8 BATTERY® for information on Ni-MH battery recycling

and disposal bans/restrictions in your area. VTech’s involvement

in this program is part of its commitment to protecting our

environment and conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered

trademarks of Call2recycle, Inc.

FCC, ACTA and IC regulations

FCC Part 15

NOTE: This equipment has been tested and found to comply

with the requirements for a Class B digital device under Part 15

of the Federal Communications Commission (FCC) rules. These

requirements are intended to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

WARNING: Changes or modiﬁcations to this equipment not

expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation. Privacy of communications may not be

ensured when using this telephone.

To ensure safety of users, the FCC/ISEDC has established

criteria for the amount of radio frequency energy that can

be safely absorbed by a user or bystander according to the

intended usage of the product. This product has been tested

and found to comply with the FCC/ISEDC criteria. The handset

may be safely held against the ear of the user. The telephone

base shall be installed and used such that parts of the user’s

body other than the hands are maintained at a distance of

approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian

requirement:

CAN ICES-3 (B)/NMB-3(B).

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and

with technical requirements adopted by the Administrative

Council for Terminal Attachments (ACTA). The label on the

back or bottom of this equipment contains, among other

things, a product identiﬁer in the format US:AAAEQ##TXXXX.

This identiﬁer must be provided to your telephone service

provider upon request.

The plug and jack used to connect this equipment to premises

wiring and the telephone network must comply with

applicable Part 68 rules and technical requirements adopted

by ACTA. A compliant telephone cord and modular plug is

provided with this product. It is designed to be connected to

a compatible modular jack that is also compliant. An RJ11 jack

should normally be used for connecting to a single line and an

RJ14 jack for two lines. See the installation instructions in the

user’s manual.

The Ringer Equivalence Number (REN) is used to determine

how many devices you may connect to your telephone line

and still have them ring when you are called. The REN for this

product is encoded as the 6th and 7th characters following the

US: in the product identiﬁer (e.g., if ## is 03, the REN is 0.3). In

most, but not all areas, the sum of all RENs should be ﬁve (5.0)

or less. For more information, please contact your telephone

service provider.

This equipment must not be used with Party Lines. If you have

specially wired alarm dialing equipment connected to your

telephone line, ensure the connection of this equipment

does not disable your alarm equipment. If you have questions

about what will disable alarm equipment, consult your

telephone service provider or a qualiﬁed installer.

If this equipment is malfunctioning, it must be unplugged

from the modular jack until the problem has been corrected.

Replacement to this telephone equipment can only be made

by the manufacturer or its authorized agents. For replacement

procedures, follow the instructions outlined under the

Limited warranty.

If this equipment is causing harm to the telephone network,

the telephone service provider may temporarily discontinue

your telephone service. The telephone service provider is

required to notify you before interrupting service. If advance

notice is not practical, you will be notiﬁed as soon as possible.

You will be given the opportunity to correct the problem and

the telephone service provider is required to inform you of

your right to ﬁle a complaint with the FCC. Your telephone

service provider may make changes in its facilities, equipment,

operation, or procedures that could affect the proper

functioning of this product. The telephone service provider is

required to notify you if such changes are planned.

If this product is equipped with a corded or cordless handset,

it is hearing aid compatible.

If this product has memory dialing locations, you may choose

to store emergency telephone numbers (e.g., police, ﬁre,

medical) in these locations. If you do store or test emergency

numbers, please:

Remain on the line and brieﬂy explain the reason for the call

before hanging up.

Perform such activities in off-peak hours, such as early

morning or late evening.

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s)

that comply with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s). Operation is

subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including

interference that may cause undesired operation of the

device.

Privacy of communications may not be ensured when using

this telephone.

The term ‘’IC:‘’ before the certiﬁcation/registration number

only signiﬁes that the Industry Canada technical speciﬁcations

were met.

The Ringer Equivalence Number (REN) for this terminal

equipment is 0.1. The REN indicates the maximum number of

devices allowed to be connected to a telephone interface.

The termination of an interface may consist of any combination

of devices subject only to the requirement that the sum of the

RENs of all the devices not exceed ﬁve.

This product meets the applicable Innovation, Science and

Economic Development Canada technical speciﬁcations.

California energy commission

battery charging testing

instructions

This telephone is set up to comply with the energy-conserving

standards right out of the box. These instructions are intended

for California Energy Commission (CEC) compliance testing only.

When the CEC battery charging testing mode is activated, all

telephone functions, except battery charging, will be disabled.

To activate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power

outlet. Make sure all handsets are plugged with charged

batteries before proceeding.

2. While you press and hold /FIND HANDSET, plug the

telephone base power adapter back to the power outlet.

3. After about 20 seconds, when the IN USE light starts

ﬂashing, release /FIND HANDSET and then press it again

within 2 seconds. When the phone successfully enters the

CEC battery charging testing mode, the IN USE light turns

off and all handsets display To register HS... and see manual

alternatively.

When the phone fails to enter this mode, repeat Step 1 through

Step 3 above.

To deactivate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power

outlet, and then plug it back in. Then the telephone base is

powered up as normal.

2. Place the handset in the telephone base to register it back. It

displays Registering...

The handset show Registered and you hear a beep when the

registration process completes. The registration process takes

about 60 seconds to complete.

Limited Warranty

What does this limited warranty cover?

The manufacturer of this VTech product, VTech

Communications, Inc. (“VTech”), warrants to the holder of a

valid proof of purchase (“Consumer” or “you”) that the Product

and all accessories provided by VTech in sales package

(“Product”) are free from material defects in material and

workmanship, pursuant to the following terms and conditions,

when installed and used normally and in accordance with

operating instructions. This limited warranty extends only to

the Consumer for Products purchased and used in the United

States of America and Canada.

What will VTech Communications do if the Product is not free

from material defects in materials and workmanship during

the limited warranty period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service

representative will replace at VTech’s option, without charge,

a Materially Defective Product. If we choose to replace the

Product, we may replace it with a new or refurbished Product

of the same or similar design. VTech will return replacement

products to you in working condition. VTech will retain

defective parts, modules, or equipment. Replacement of

the Product, at VTech’s option, is your exclusive remedy. You

should expect the replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the product extends for

ONE (1) YEAR from date of purchase (90 days on products

purchased as Refurbished*). This limited warranty also applies

to replacement Products for a period of either (a) 90 days from

the date the replacement Product is shipped to you or (b)

the time remaining on the original one-year limited warranty

(90-day limited warranty on products that are purchased as

Refurbished*), whichever is longer.

*Refurbished products purchased from our online store carry a

90-day replacement warranty.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident,

shipping or other physical damage, improper installation,

abnormal operation or handling, neglect, inundation,

ﬁre, water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration

or modiﬁcation by anyone other than an authorized

service representative of VTech; or

3. Product to the extent that the problem experienced is

caused by signal conditions, network reliability or cable

or antenna systems; or

4. Product to the extent that the problem is caused by use

with non-VTech electrical accessories; or

5. Product whose warranty/quality stickers, Product serial

number plates or electronic serial numbers have been

removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair

from outside the United States, or used for commercial

or institutional purposes (including but not limited to

Products used for rental purposes); or

7. Product returned without valid proof of purchase (see 2

below); or

8. Charges for installation or set up, adjustment of customer

controls, and installation or repair of systems outside the

unit.

How do you get warranty service?

To obtain warranty service in the United States of America,

please visit our website at www.vtechphones.com or call 1

(800) 595-9511 for instructions regarding where to return the

Product. In Canada, go to phones.vtechcanada.com or dial 1

(800) 267-7377.

NOTE: Before calling for service, please review the user’s

manual - a check of the Product’s controls and features may

save you a service call.

Except as provided by applicable law, you assume the risk

of loss or damage during transit and transportation and are

responsible for delivery or handling charges incurred in the

transport of Product(s) to the service location. VTech will

return replaced product under this limited warranty to you,

transportation, delivery or handling charges prepaid. VTech

assumes no risk for damage or loss of the Product in transit.

What must you return with the Product to get warranty

service?

1. Return the entire original package and contents including

the Product to the VTech service location along with a

description of the malfunction or difﬁculty;

2. Include “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model) and

the date of purchase or receipt; and

3. Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement

between you and VTech. It supersedes all other written or

oral communications related to this product. VTech provides

no other warranties for this product. The warranty exclusively

describes all of VTech’s responsibilities regarding the product.

There are no other expressed warranties. No one is authorized

to make modiﬁcations to this warranty and you should not rely

on any such modiﬁcation.

State Law Rights: This warranty gives you speciﬁc legal rights,

and you may also have other rights which vary from state to

state.

Limitations: Implied warranties, including those of ﬁtness for a

particular purpose and merchantability (an unwritten warranty

that the product is ﬁt for ordinary use) are limited to one year

from date of purchase. Some states do not allow limitations on

how long an implied warranty lasts, so the above limitation may

not apply to you.

In no event shall VTech be liable for any indirect, special,

incidental, consequential, or similar damages (including,

but not limited to lost proﬁts or revenue, inability to use the

product, or other associated equipment, the cost of substitute

equipment, and claims by third parties) resulting from the

use of this product. Some states do not allow the exclusion

or limitation of incidental or consequential damages, so the

above limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof of

purchase

Disclaimer and Limitation of

Liability

VTech Communications, Inc. and its suppliers assume no

responsibility for any damage or loss resulting from the use

of this user’s manual. VTech Communications, Inc. and its

suppliers assume no responsibility for any loss or claims by

third parties that may arise through the use of this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road - Ste 555 Tigard,

OR 97223, United States

Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in

Canada

Technical speciﬁcations

Frequency

control

Crystal controlled PLL synthesizer

Transmit

frequency

Handset: 1921.536-1928.448 MHz

Telephone Base: 1921.536-1928.448

MHz

Channels DECT channel: 5

Nominal

effective range

Maximum power allowed by FCC

and IC. Actual operating range may

vary according to environmental

conditions at the time of use.

Power

requirement

Handset: 2.4V Ni-MH battery

Telephone base: 6V DC @ 0.4A

Charger: 6V DC @ 0.4A

Memory Phonebook: 50 memory locations;

up to 30 digits and 15 characters

Caller ID log: 30 memory locations;

up to 24 digits and 15 characters

Call block: 20 entries

(US)

(CA)

Telephones identiﬁed with this logo

have reduced noise and interference

when used with most T-coil equipped

hearing aids and cochlear implants. The

TIA-1083 Compliant Logo is a trademark

of the Telecommunications Industry

Association. Used under license.

Compatible with

Hearing Aid T-Coil

TIA-1083

The ENERGY STAR® program (www.

energystar.gov) recognizes and

encourages the use of products that save

energy and help protect our environment.

We are proud to mark this product

with the ENERGY STAR® label indicating

it meets the latest energy efﬁciency

guidelines.

VTech CS5119-13 Manuel utilisateur

Marque: VTech

Modèle: CS5119-13

Catégorie: Téléphones

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: VTech CS5119-13 User manual