CS6719
CS6719-15
CS6719-16
CS6719-17
CS6719-2
CS6719-26
CS6719-27
Abridged user’s manual
Scan the QR code for
support information
When using your telephone equipment, basic safety
precautions should always be followed to reduce the risk of
fire, electric shock and injury, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the
product.
3. Unplug this product from the wall outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a damp cloth
for cleaning.
4. CAUTION: Do not install the telephone base at a height
above 2 meters.
5. Do not use this product near water such as near a bath tub,
wash bowl, kitchen sink, laundry tub or a swimming pool,
or in a wet basement or shower.
6. Do not place this product on an unstable table, shelf,
stand or other unstable surfaces.
7. Avoid placing the telephone system in places with extreme
temperature, direct sunlight, or other electrical devices.
Protect your phone from moisture, dust, corrosive liquids
and fumes.
8. Slots and openings in the back or bottom of the telephone
base and handset are provided for ventilation. To protect
them from overheating, these openings must not be
blocked by placing the product on a soft surface such as
a bed, sofa or rug. This product should never be placed
near or over a radiator or heat register. This product should
not be placed in any area where proper ventilation is not
provided.
9. This product should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power supply in your home or
office, consult your dealer or local power company.
10. Do not allow anything to rest on the power cord. Do not
install this product where the cord may be walked on.
11. Never push objects of any kind into this product through
the slots in the telephone base or handset because they
may touch dangerous voltage points or create a short
circuit. Never spill liquid of any kind on the product.
12. To reduce the risk of electric shock, do not disassemble
this product, but take it to an authorized service facility.
Opening or removing parts of the telephone base or
handset other than specified access doors may expose
you to dangerous voltages or other risks. Incorrect
reassembling can cause electric shock when the product
is subsequently used.
13. Do not overload wall outlets and extension cords.
14. Unplug this product from the wall outlet and refer
servicing to an authorized service facility under the
following conditions:
• When the power supply cord or plug is damaged or
frayed.
• If liquid has been spilled onto the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operation instructions. Improper
adjustment of other controls may result in damage
and often requires extensive work by an authorized
technician to restore the product to normal operation.
• If the product has been dropped and the telephone
base and/or handset has been damaged.
• If the product exhibits a distinct change in performance.
15. Avoid using a telephone (other than cordless) during an
electrical storm. There is a remote risk of electric shock
from lightning.
16. Do not use the telephone to report a gas leak in the
vicinity of the leak. Under certain circumstances, a spark
may be created when the adapter is plugged into the
power outlet, or when the handset is replaced in its
cradle. This is a common event associated with the
closing of any electrical circuit. The user should not
plug the phone into a power outlet, and should not
put a charged handset into the cradle, if the phone is
located in an environment containing concentrations
of flammable or flame-supporting gases, unless there
is adequate ventilation. A spark in such an environment
could create a fire or explosion. Such environments
might include: medical use of oxygen without adequate
ventilation; industrial gases (cleaning solvents; gasoline
vapors; etc.); a leak of natural gas; etc.
17. Only put the handset of your telephone next to your ear
when it is in normal talk mode.
18. The power adapter is intended to be correctly oriented
in a vertical or floor mount position. The prongs are not
designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
19. For pluggable equipment, the socket-outlet shall
be installed near the equipment and shall be easily
accessible.
20. CAUTION: Use only the batteries indicated
in this manual. There may be a risk of
explosion if a wrong type of battery is used for the
handset. Use only the supplied rechargeable batteries
or replacement batteries (BT162342/BT262342) for the
handset. Do not dispose of batteries in a fire. They may
explode. Disposed of used batteries according to the
instruction.
• Do not use the battery in following conditions:
»High or low extreme temperature during use, storage
or transportation.
»Replacement of a battery with an incorrect type that can
defeat a safeguard.
»Disposal of a battery into fire or a hot oven, or
mechanically crushing or cutting of a battery, that can
result in an explosion.
»Leaving a battery in an extremely high temperature
surrounding environment that can result in an explosion
or the leakage of flammable liquid or gas.
»A battery subjected to extremely low air pressure that
can result in an explosion or the leakage of flammable
liquid or gas.
21. Use only the adapter included with this product.
Incorrect adapter polarity or voltage can seriously
damage the product.
22. The applied nameplate is located at the bottom or near
of the product.
SAVE THESE INSTRUCTIONS
Battery
• Use only the battery provided or equivalent. To order
a replacement, visit our website at www.vtechphones.
com or call 1 (800) 595-9511. In Canada, go to phones.
vtechcanada.com or call 1 (800) 267-7377.
• Do not dispose of the battery in a fire. Check with
local waste management codes for special disposal
instructions.
• Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause burns or injury
to the eyes or skin. The electrolyte may be toxic if
swallowed.
• Exercise care in handling batteries in order not to create
a short circuit with conductive materials.
• Charge the battery provided with this product only
in accordance with the instructions and limitations
specified in this manual.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless
telephones):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless telephones and
implanted cardiac pacemakers. Supported by the U.S. Food
and Drug Administration, WTR recommends to physicians
that:
Pacemaker patients
• Should keep wireless telephones at least six inches from
the pacemaker.
• Should NOT place wireless telephones directly over
the pacemaker, such as in a breast pocket, when it is
turned ON.
• Should use the wireless telephone at the ear opposite
the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless telephones.
About cordless telephones
• Privacy: The same features that make a cordless
telephone convenient create some limitations.
Telephone calls are transmitted between the telephone
base and the cordless handset by radio waves, so
there is a possibility that the cordless telephone
conversations could be intercepted by radio receiving
equipment within range of the cordless handset. For
this reason, you should not think of cordless telephone
conversations as being as private as those on corded
telephones.
• Electrical power: The telephone base of this cordless
telephone must be connected to a working electrical
outlet. The electrical outlet should not be controlled by
a wall switch. Calls cannot be made from the cordless
handset if the telephone base is unplugged, switched
off or if the electrical power is interrupted.
• Potential TV interference: Some cordless telephones
operate at frequencies that may cause interference
to televisions and VCRs. To minimize or prevent such
interference, do not place the telephone base of the
cordless telephone near or on top of a TV or VCR.
If interference is experienced, moving the cordless
telephone farther away from the TV or VCR often
reduces or eliminates the interference.
• Rechargeable batteries: Exercise care in handling
batteries in order not to create a short circuit with
conducting material such as rings, bracelets and keys.
The battery or conductor may overheat and cause harm.
Observe proper polarity between the battery and the
battery charger.
• Nickel-metal hydride rechargeable batteries: Dispose
of these batteries in a safe manner. Do not burn or
puncture the battery. Like other batteries of this type,
if burned or punctured, they could release caustic
material which could cause injury.
Go to www.vtechphones.com (US) to register your
product for enhanced warranty support and latest
VTech product news.
Go to phones.vtechcanada.com (Canada) for the latest
VTech product news.
Specifications are subject to change without notice.
© 2022 VTech Communications, Inc. |
© 2022 VTech Technologies Canada Ltd.
All rights reserved. 09/22.
CS6719-X_HSDE56_US-CAN_ACIB_2.0_220920
HSDE56-BSDE58BVSD
What’s in the box
Your telephone package contains the following
items. Save your sales receipt and original packaging
in case it is necessary to ship your telephone for
warranty service.
Abridged
user’s
manual
1 set for CS6919-2/
CS6919-26/CS6919-27
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT162342/BT262342 (2.4V 300mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR1939
1 set for CS6719/
CS6719-15/CS6719-16/
CS6719-17 |
2 sets for CS6919-2/
CS6919-26/CS6919-27
Install and Connect | Mount (optional)
Install the battery
THIS SIDE UP
THIS SIDE UP
THIS SIDE UP
Connect and charge
Connect the telephone base
If you subscribe to digital subscriber
line (DSL) high-speed Internet service
through your telephone line, make sure
you connect a DSL filter (not included)
to the telephone wall jack.
12 hrs
Mount (optional)
a
b
A
c
d
Setup Overview
After the telephone is installed or power returns
following a power outage and battery depletion, the
handset will prompt you to set the date and time.
Date and time
Follow the steps below to set the date and time. For
example, if the date is 25 January, 2022, and the time
is 11:07 AM:
When the handset
prompts you to set the
date and time:
Date:MM/DD/YY
ECO
Date:01/2?/YY
ECO
Date:01/25/22
ECO
1. Enter the date. 2. Press SELECT.
Time: 1?:MM --
ECO
Time: 11:07 AM
ECO
3. Enter the time. 4. Press q/p to select
AM to PM.
5. Press SELECT to save.
NOTE: If you have skipped the prompt, you
can set up again by pressing MENU. Scroll
to choose Set date/time and press SELECT.
Then, follow the steps above.
Change LCD language settings
You can select English, French, or Spanish to be
used in all screen displays:
HANDSET
ECO
11:07 1/25
AM
Settings
ECO
1. Press MENU.2. Press q/p to scroll
to Settings, then
press SELECT.
LCD language
ECO
English
ECO
3. Press SELECT
to select LCD
language.
4. Press q/p to
choose your desired
language and press
SELECT.
NOTE: If you accidentally set the LCD
language to Spanish or French, press
MENU and then enter *364# to change
the handset LCD language back to English
while the handset is not in use.
Telephone base
a
b
c
d
1 – light
• Flashes when there is an incoming call, or
another telephone sharing the same line is in
use.
• On when the telephone is in use.
2 –
• Page all system handsets.
3 – Charging pole
4 – Charge light
Charger
a
1 – Charging pole
Handset
a
b
c
d
e
f
g
h
i
j
n
p
o
k
l
m
1 – Handset earpiece
2 – LCD display
3 –
• Show the menu.
• While in a menu, press to select an item, or
save an entry or setting.
4 –
• Hang up a call.
• Return to the previous menu.
• Press and hold to exit menu display without
making changes.
• Delete digits while predialing.
• Silence the handset ringer temporarily while
the phone is ringing.
• Press and hold to erase the missed call
indicator while the handset is not in use.
5 –
• Press and hold to turn on or off the quiet
mode.
• Press repeatedly to show other dialing options
when reviewing a caller ID log entry.
6 –
• Press to start an intercom conversation or
transfer a call (for multi-handset models only).
7 – Microphone
8 –
• Make or answer a call using the handset
speakerphone.
• During a call, press to switch between the
speakerphone and the handset earpiece.
9 –
• Mute the microphone during a call.
• Silence the handset ringer temporarily while
the phone is ringing.
• Delete the displayed entry while reviewing
the phonebook, caller ID log, or redial list.
• Delete digits or characters when entering
numbers or names.
10 –
• Switch to tone dialing temporarily during a
call.
11 –
• Press to add a space when entering names.
12 –
• Press repeatedly to add or remove 1 in front
of the caller ID log entry before dialing or
saving it to the phonebook.
• Press and hold to set or dial your voicemail
number.
13 –
• Make or answer a call.
• Answer an incoming call when you receive a
call waiting alert.
14 –
• Review the redial list.
• Press and hold to insert a dialing pause
while dialing or entering numbers into the
phonebook.
15 –
• Review the phonebook when the phone is
not in use.
• Scroll up while in a menu, or in the
phonebook, caller ID log or redial list.
• Move the cursor to the right when entering
numbers or names.
• Increase the listening volume during a call.
• Review the caller ID log when the telephone
is not in use.
• Scroll down while in a menu, or in the
phonebook, caller ID log or redial list.
• Move the cursor to the left when entering
numbers or names.
• Decrease the listening volume during a call.
16 – light
• On when the handset is charging.
Display icons
The battery icon flashes when
the battery is low and needs
charging.
The battery icon animates when
the battery is charging.
The battery icon becomes
solid when the battery is fully
charged.
The handset ringer is turned off.
There are new voicemail
received from your telephone
service provider.
NEW New caller ID log entry.
ECO The ECO mode activates
automatically to reduce power
consumption when the handset
is within range from the
telephone base.
Telephone operations Use the handset menu
1. Press MENU when the phone is not in use.
2. Press q or p until the screen displays the
desired feature menu.
3. Press SELECT to enter that menu.
• To return to the previous menu, press CANCEL.
• To exit menu display, press and hold CANCEL.
Make a call
• Press or , and then dial the telephone
number.
Answer a call
• Press , or any dialing keys.
End a call
• Press OFF or put the handset back in the
telephone base or charger.
Speakerphone
• During a call, press on the handset to switch
between speakerphone and handset earpiece.
Volume
• During a call, press p/VOLUME/q to adjust
the listening volume.
Mute
The mute function allows you to hear the other party
but the other party cannot hear you.
1. During a call, press MUTE. The handset displays
Muted.
2. Press MUTE again to resume the conversation.
The handset displays Microphone ON briefly.
Join a call in progress
You can use up to two system handsets at a time
on an outside call.
• When a handset is already on a call, press or
on another handset to join the call.
• Press OFF or place the handset in the
telephone base or charger to exit the call. The
call continues until all handsets hang up.
Call waiting
When you subscribe to call waiting service from
your telephone service provider, you hear an
alert tone if there is an incoming call while you are
already on a call.
• Press FLASH to put the current call on hold and
take the new call.
• Press FLASH at any time to switch back and
forth between calls.
Find handset
Use this feature to find the system handset.
To start paging:
• Press FIND HANDSET on the telephone base
when not in use. All idle handsets ring and
display ** Paging **.
To end paging:
• Press FIND HANDSET at the telephone base.
-OR-
• Press , , OFF or any dialing keys on the
handset.
-OR-
• Place the handset in the telephone base or
charger.
NOTE:
Do not press and hold FIND HANDSET
for more than 4 seconds. It may lead to
handset deregistration.
Redial list
Each handset stores the last 10 telephone numbers
dialed. When there are already 10 entries, the
oldest entry is deleted to make room for the new
entry.
Review and dial a redial list entry
1. Press REDIAL when the handset is not in use.
2. Press q, p or REDIAL repeatedly until the
desired entry displays.
3. Press or to dial.
Delete a redial list entry
• When the desired redial entry displays, press
DELETE.
Intercom
Use the intercom features for conversations
between two handsets.
1. Press INT on your handset when not in use. Use
the dialing keys to enter a destination handset
number if necessary.
2. To answer the intercom call, press , , INT
or any dialing key on the destination handset.
3. To end the intercom call, press OFF or place the
handset back in the telephone base or charger.
Answer an incoming call during an intercom
call
If you receive an incoming call during an intercom
call, there is an alert tone.
• To answer the outside call, press . The
intercom call ends automatically.
• To end the intercom call without answering
the outside call, press OFF. The telephone
continues to ring.
(US)
(CA)
Important safety instructions
Call transfer using intercom
While on an outside call, you can use the intercom
feature to transfer the call from one handset to
another.
1. Press INT on your handset during a call. The
current call is put on hold. Use the dialing
keys to enter a destination handset number if
necessary.
2. To answer the intercom call on the destination
handset, press , , INT or any dialing key on
the destination handset. You can now have a
private conservation before transferring the
call.
3. From this intercom call, you have the following
options:
• You can let the destination handset join
you on the outside call in a three-way
conversation. Press and hold INT on the
originating handset.
• You can transfer the call. Press OFF, or place
your handset back in the telephone base
or charger. The destination handset is then
connected to the outside call.
• You can press INT to switch between the
outside call (Outside call displays) and the
intercom call (Intercom displays).
• The destination handset can end the
intercom call by pressing OFF, or by placing
the handset back in the telephone base or
charger. The outside call continues with the
original system handset.
Phonebook
The phonebook can store up to 50 entries, which
are shared by all handsets. Each entry may consist
of a telephone number up to 30 digits, and a name
up to 15 characters.
Add a phonebook entry
1. Enter the number when the phone is not in use.
Press MENU, then go to Step 3.
-OR-
Press MENU when the phone is not in use,
then scroll to Phonebook and press SELECT.
Press SELECT again to choose Add new entry.
2. Use the dialing keys to enter the number.
-OR-
Copy a number from the redial list by pressing
REDIAL and then press q, p or REDIAL
repeatedly to select a number. Press SELECT to
copy the number.
3. Press SELECT to move on to enter the name.
4. Use the dialing keys to enter the name.
Additional key presses show other characters of
that particular key.
5. Press SELECT to save.
While entering names and numbers, you can:
• Press DELETE to backspace and erase a digit or
character.
• Press and hold DELETE to erase the entire entry.
• Press q or p to move the cursor to the left or
right.
• Press and hold PAUSE to insert a dialing pause
(for entering numbers only).
• Press 0 to add a space (for entering names
only).
• Press to add ( appears) or to add #
( appears) (for entering phone numbers only).
Review a phonebook entry
Entries are sorted alphabetically.
1. Press when the phone is not in use.
2. Scroll to browse through the phonebook, or
use the dialing keys to start a name search.
-OR-
1. Press MENU when the phone is not in use.
2. Scroll to Phonebook, and then press SELECT.
3. Scroll to Review, and then press SELECT.
4. Scroll to browse through the phonebook.
Delete a phonebook entry
1. When the desired entry displays, press DELETE.
2. When the handset displays Delete entry?, press
SELECT.
Edit a phonebook entry
1. Search for or review the phonebook entries
(see Review a phonebook entry).
2. When the desired entry displays, press SELECT.
3. Use the dialing keys to edit the number, then
press SELECT.
4. Use the dialing keys to edit the name, then
press SELECT to save.
Dial a phonebook entry
1. Search for or review the phonebook entries
(see Review a phonebook entry).
2. When the desired entry appears, press or
to dial.
Caller ID
If you subscribe to caller ID service, information
about each caller appears after the first or
second ring. If you answer a call before the caller
information appears on the screen, it will not be
saved in the caller ID log.
The caller ID log stores up to 50 entries. Each entry
has up to 24 digits for the phone number and 15
characters for the name.
If the telephone number has more that 15 digits,
only the last 15 digits appear. If the name has more
than 15 characters, only the first 15 characters are
shown and saved in the caller ID log.
Review a caller ID log entry
1. Press CID when the phone is not in use.
2. Scroll to browse through the caller ID log.
-OR-
1. Press MENU when the phone is not in use.
2. Scroll to Caller ID log, and then press SELECT.
3. Press SELECT to choose Review.
4. Scroll to browse through the caller ID log.
• Press # repeatedly to show different dialing
options.
• Press 1 repeatedly if you need to add or
remove 1 in front of the phone number.
Missed call indicator
When there are calls that have not been reviewed
in the caller ID log, the handset displays XX missed
calls.
Each time you review a caller ID log entry marked
NEW, the number of missed calls decreases by
one.
When you have reviewed all the missed calls, the
missed call indicator no longer displays.
If you do not want to review the missed calls
one by one, press and hold CANCEL on the idle
handset to erase the missed call indicator. All the
entries are then considered old.
Dial a caller ID log entry
1. Search for or review the caller ID log entries
(see Review a caller ID log entry).
2. When the desired entry appears, press or
to dial.
Save a caller ID log entry to the phonebook
1. Search for or review the caller ID log entries
(see Review a caller ID log entry).
2. When the desired caller ID log entry displays,
press SELECT.
3. Use the dialing keys to edit the number, if
necessary. Then press SELECT.
4. Use the dialing keys to edit the name, if
necessary. Then press SELECT to save.
Delete the caller ID log entries
1. Search for or review the caller ID log entries
(see Review a caller ID log entry).
2. When the desired caller ID log entry displays,
press DELETE.
To delete all caller ID log entries:
1. Press MENU when the phone is not in use.
2. Scroll to Caller ID log and then press SELECT.
3. Scroll to Delete all and then press SELECT.
4. When the screen shows Delete all?, press
SELECT to confirm.
Sound settings
Key tone
You can turn the key tone on or off.
1. Press MENU when the handset is not in use.
2. Scroll to Settings and then press SELECT.
3. Scroll to choose Key tone, then press SELECT.
4. Scroll to chooseOn or Off, then press SELECT
to save.
Ringer tone
You can choose from different ringer tones for
each handset.
1. Press MENU when the handset is not in use.
2. Scroll to Ringers and then press SELECT.
3. Scroll to choose Ringer tone, then press
SELECT.
4. Scroll to sample each ringer tone, then press
SELECT to save.
NOTE: If you turn off the ringer volume,
you will not hear ringer tone samples.
Ringer volume
You can adjust the handset ringer volume level, or
turn the ringer off.
1. Press MENU when the handset is not in use.
2. Scroll to Ringers and then press SELECT.
3. Press SELECT again to choose Ringer volume.
4. Press q or p to sample each volume level,
then press SELECT to save.
NOTE: When the ringer volume is set to
Off, the handset still rings when you press
FIND HANDSET at the telephone base.
Temporary ringer silencing
When the telephone is ringing, you can temporarily
silence the ringer without disconnecting the call. The
next call rings normally at the preset volume.
To silence the handset ringer:
• Press OFF or MUTE on the handset. The handset
displays and Ringer muted briefly.
Quiet mode
You can turn on the quiet mode for a period of
time. During this period, all tones (except paging
tone) and call screening are muted.
1. Press and hold on the handset when it
is not in use.
2. Use the dialing keys (0-9) to enter the duration,
and then press SELECT to save.
• To turn off the quiet mode, press and hold
on the handset when it is not in use.
Retrieve voicemail from
telephone service
Voicemail is a feature available from most
telephone service providers. It may be included
with your telephone service, or may be optional.
Fees may apply.
Retrieve voicemail
When you received a voicemail, the handset
displays and New voicemail. To retrieve, you
typically dial an access number provided by your
telephone service provider, and then enter a security
code. Contact your telephone service provider
for instructions on how to configure the voicemail
settings and listen to messages.
NOTE: After you have listened to all new
voicemail messages, the indicators on the
handset turn off automatically.
Set your voicemail number
You can save your access number on each handset
for easy access to your voicemail.
After you saved the voicemail number, you can
press and hold to retrieve voicemail.
1. Press MENU when the phone is not in use.
2. Scroll to Settings and then press SELECT.
3. Scroll to Voicemail # and then press SELECT.
4. Use the dialing keys to enter the voicemail
number (up to 30 digits).
5. Press SELECT to save.
Clear the new voicemail indicators
If you have retrieved your voicemail while away
from home, and the handset still displays the new
voicemail indicators, use this feature to clear the
indicators.
NOTE: This feature clears the indicators
only, it does not delete your voicemail
messages.
1. Press MENU when the phone is not in use.
2. Scroll to Settings and then press SELECT.
3. Scroll to Clr voicemail and then press SELECT.
4. Press SELECT again to confirm. You hear a
confirmation tone.
ECO mode
This power conserving technology reduces power
consumption for optimal battery performance. The
ECO mode activates automatically whenever the
handset is synchronized with the telephone base.
General product care
Taking care of your telephone
Your cordless telephone contains sophisticated
electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original
packing materials to protect your telephone if you
ever need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do
not use the handset outdoors in the rain, or handle
it with wet hands. Do not install the telephone
base near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment. For your
own safety, take caution when using electrical
appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that
should retain its luster for many years. Clean it
only with a dry non-abrasive cloth. Do not use
dampened cloth or cleaning solvents of any kind.
Need help?
For operations and guides to help you using your
telephone, and for the latest information and
supports, go and check the online help topics and
online FAQs.
Use your smartphone or mobile device to access our
online help.
• Go to
https://help.vtechphones.com/CS6719 (US); OR
https://phones.vtechcanada.com/en/support/
general/manuals?model=CS6719 (Canada)
• Scan the QR code on the
right. Launch the camera app
or QR code scanner app on
your smartphone or tablet.
Hold the device’s camera up to
the QR code and frame it. Tap
the notification to trigger the
redirection of the online help.
- If the QR code is not clearly
displayed, adjust your camera’s
focus by moving your device
closer or further away until it is
clear.
You can also call our Customer
Support at 1 (800) 595-9511
[in US] or 1 (800) 267-7377 [in
Canada] for help.
For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures
corporelles ou d’électrocution, suivez toujours ces mesures
préventives de base lorsque vous utilisez votre téléphone :
1. Lisez et comprenez bien toutes les instructions.
2. Observez toutes les instructions et mises en garde inscrites
sur l’appareil.
3. Débranchez ce téléphone de la prise murale avant de le
nettoyer. N’utilisez pas de nettoyeurs liquides ni en aérosol.
N’utilisez qu’un chiffon doux et légèrement humecté.
4. ATTENTION: Ne pas installer le socle téléphonique à une
hauteur supérieure à 2 mètres.
5. N’utilisez pas ce produit près de l’eau, tel que près d’un
bain, d’un lavabo, d’un évier de cuisine, d’un bac de lavage
ou d’une piscine, ou dans un sous-sol humide ou sous la
douche.
6. Ne déposez pas ce téléphone sur un chariot, support
ou table chancelants. L’appareil pourrait tomber et être
sérieusement endommagé.
7. Évitez d’installer le système téléphonique dans les endroits
soumis à une température extrême, à la lumière directe
du soleil ou à proximité immédiate d’autres appareils
électriques ou électroniques. Protégez votre téléphone
contre les sources d’humidité, la poussière, les vapeurs et
les liquides corrosifs.
8. Le boîtier de l’appareil est doté de fentes et d’ouvertures
d’aération situées à l’arrière ou en dessous. Afin
d’empêcher la surchauffe, ces ouvertures ne doivent
pas être obstruées en plaçant l’appareil sur un lit, divan,
tapis ou autre surface similaires. Ne placez pas cet
appareil à proximité d’un élément de chauffage ni d’une
plinthe électrique. De plus, ne l’installez pas dans une
unité murale ou un cabinet fermé qui ne possède pas
d’aération adéquate.
9. Ne faites fonctionner cet appareil qu’avec le type
d’alimentation indiqué sur les étiquettes de l’appareil.
Si vous ne connaissez pas le voltage de votre maison,
consultez votre marchand ou votre fournisseur d’électricité.
10. Ne déposez rien sur le cordon d’alimentation. Installez cet
appareil dans un endroit sécuritaire, là où personne ne
pourra trébucher sur la ligne d’alimentation ni le cordon
téléphonique modulaire.
11. N’insérez jamais d’objets à travers les fentes et ouvertures
de cet appareil, car ils pourraient toucher à des points
de tension dangereux ou court-circuiter des pièces, ce
qui constituerait un risque d’incendie ou d’électrocution.
N’échappez pas de liquides dans l’appareil.
12. Afin de réduire les risques d’électrocution, ne démontez
pas l’appareil, mais apportez-le plutôt à un centre de
service qualifié s’il doit être réparé. En enlevant le
couvercle, vous vous exposez à des tensions dangereuses
ou autres dangers similaires. Un remontage inadéquat
peut être à l’origine d’une électrocution lors d’une
utilisation ultérieure de l’appareil. Débranchez l’appareil
avant de procéder au nettoyage. Utilisez un chiffon
humide et doux.
13. Ne surchargez pas les prises de courant et les rallonges.
14. Débranchez cet appareil de la prise de courant et
communiquez avec le département de service à la clientèle
de VTech dans les cas suivants :
• Lorsque le cordon d’alimentation est endommagé ou
écorché.
• Si du liquide a été échappé dans l’appareil.
• Si l’appareil a été exposé à une source d’humidité telle
que la pluie ou l’eau.
• Si le produit ne fonctionne pas normalement en
respectant les instructions de fonctionnement. Réglez
uniquement les commandes indiquées dans le les
instructions de fonctionnement. Les réglages incorrects
des autres commandes pourraient provoquer un
dommage qui pourrait exiger un travail exhaustif
de la part d’un technicien autorisé afin de rétablir le
fonctionnement normal de l’appareil.
• Si le produit a été échappé et que le socle et/ou le
combiné a été endommagé.
• Si le produit affiche une nette diminution de sa
performance.
15. Évitez d’utiliser un téléphone (autre qu’un sans fil) pendant
un orage. Les éclairs peuvent être à l’origine d’une
électrocution.
16. N’utilisez pas le téléphone pour rapporter une fuite de
gaz à proximité de la fuite. En certaines circonstances, une
flammèche pourrait être provoquée lorsque l’adaptateur
est branché à une prise de courant, ou lorsque le
combiné est déposé sur le socle. Ceci est un événement
commun associé à la fermeture d’un circuit électrique.
L’utilisateur ne devrait pas brancher le téléphone à une
prise de courant, et ne devrait pas déposer le combiné
chargé sur le socle, si le téléphone se trouve à proximité
d’un endroit comportant des concentrations de gaz
inflammables, à moins que la ventilation soit adéquate.
Une flammèche dans un tel endroit pourrait provoquer
un incendie ou une explosion. De tels environnements
peuvent comprendre: des endroits où l’on utilise de
l’oxygène médical sans ventilation adéquate; des gaz
industriels (dissolvants de nettoyage, des vapeurs
d’essence, etc.); une fuite de gaz naturel, etc.
17. Ne placez que le combiné de votre téléphone près de
votre oreille lorsqu’en mode de conversation.
18. Ces adaptateurs ont été conçus pour être orientés en
position verticale ou montés au sol. Les broches ne sont
pas conçues pour maintenir l’adaptateur en place si celui-ci
est barnché dans une prise au plafond ou sous une table/
armoire.
19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le
socle de prise de courant doit etre installe a proximite du
materiel et doit etre aisement accessible.
20. MISE EN GARDE: Il peut y avoir un risque
d’explosion si vous utilisez le mauvais type de piles pour
le téléphone. N’utilisez que les piles rechargeable inclus
ou les piles de rechange (BT162342/BT262342). N’incinérez
pas les piles. Celles-ci risqueraient d’exploser. Mettre au
rebut les batteries usagées conformément aux instructions
du fabricant. Débrancher les lignes téléphoniques avant le
remplacement des piles.
• Évite d’utiliser la batterie dans les conditions suivantes:
• des températures extrêmes faibles ou élevées
auxquelles une batterie peut être soumise
pendant l’utilisation, le stockage ou le transport.
• remplacement d’une batterie par un type
incorrect pouvant supprimer une protection.
• mise au rebut d’une batterie dans un feu ou dans
un four chaud, ou écrasement mécanique ou
coupure d’une batterie, susceptible de provoquer
une explosion.
• maintien d’une batterie dans un environnement
à très haute température pouvant provoquer
une explosion ou la fuite de liquide ou de gaz
inflammables.
• batterie soumise à une pression de l’air
extrêmement faible pouvant provoquer une
explosion ou la fuite de liquide ou de gaz
inflammables.
21. N’utilisez que les adaptateurs inclus avec ce produit.
L’utilisation d’un adaptateur dont la polarité ou la tension
serait inadéquate risque d’endommager sérieusement le
produit et mettre votre sécurité en péril.
22. La plaque signalétique appliquée est située au bas ou à
proximité du produit.
CONSERVEZ CES INSTRUCTIONS
Pile
• N’utilisez que la pile incluse ou l’équivalent.
• Ne jetez pas la pile au feu. Vérifiez les instructions
spécifiques de mise aux rebus auprès des autorités
locales.
• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en
échapperait est corrosif et pourrait causer des brûlures
ou des blessures aux yeux ou à la peau. L’électrolyte est
toxique si avalé.
• Soyez prudents lorsque vous manipulez les piles afin
d’éviter les courts-circuits provoqués par des matériaux
conducteurs.
• Rechargez la pile incluse avec cet appareil, selon les
instructions et limites spécifiées dans ce guide d’utilisation.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (s’applique uniquement aux
téléphones numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une
firme de recherche indépendante, a mené une évaluation
pluridisciplinaire des interférences entre les téléphones sans
fil portatifs et les stimulateurs cardiaques implantés dans
l’organisme. Appuyée par l’Administration des aliments et
drogues (FDA) des États-Unis, la firme WTR recommande aux
médecins :
Avis aux détenteurs de stimulateurs cardiaques
• Ils doivent tenir le téléphone sans fil à une distance d’au
moins six pouces du stimulateur cardiaque.
• Ils ne doivent PAS placer le téléphone sans fil directement
sur le stimulateur cardiaque, tel que dans une poche de
chemise, lorsque celui-ci est en marche.
• Ils doivent utiliser le téléphone sans fil en l’appuyant
sur l’oreille qui se trouve dans la direction opposée au
stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a pas identifié de
risque pour les détenteurs de simulateurs cardiaques causés
par les gens qui utilisent un téléphone sans fil à proximité de
ceux-ci.
À propos des téléphones sans fil
Confidentialité : Les mêmes caractéristiques qui constituent
des avantages pour les téléphones sans fil affichent
également des restrictions. Les appels téléphoniques
sont transmis entre le combiné sans fil et le socle par
le biais d’ondes radio ; il y a donc la possibilité que vos
conversations téléphoniques sans fil soient interceptées par
des équipements de réception radio se trouvant dans la
portée du combiné sans fil. Pour cette raison, vous ne devez
pas percevoir les communications téléphoniques sans fil
comme étant aussi confidentielles que celles des téléphones
à cordons.
Alimentation électrique : Le socle de ce téléphone sans fil
doit être branché à une prise électrique fonctionnelle. La
prise électrique ne doit pas être contrôlée par un interrupteur
mural. Les appels ne pourront pas être effectués du combiné
sans fil si le socle est débranché ou mis hors tension ou si le
courant est coupé.
Possibilité d’interférences aux téléviseurs : Certains
téléphones sans fil fonctionnent sur des fréquences
pouvant causer des interférences aux téléviseurs et aux
magnétoscopes. Pour réduire ou prévenir de telles
interférences, ne placez pas le socle du téléphone sans fil près
ou sur un téléviseur ou magnétoscope. S’il y a présence de
parasites, il est conseillé d’éloigner le téléphone sans fil du
téléviseur ou du magnétoscope afin de réduire possiblement
les interférences.
Piles rechargeables : Manipulez les piles avec soin afin de
ne pas les court-circuiter avec des bagues, bracelets ou clés.
Les piles ou le conducteur peut surchauffer et causer des
blessures. Respectez la polarité adéquate entre la pile et le
chargeur.
Les bloc-piles rechargeables à l’hydrure métallique de nickel
: Jetez ces blocs-piles de manière écologique et sécuritaire.
Ne les incinérez pas et ne les percez pas. Tel que les autres
piles de ce type, elles pourraient dégager une matière
toxique qui peut causer
des blessures corporelles si elles sont brûlées ou percées.
The RBRC SEAL
The RBRC seal on the nickel-metal hydride
battery indicates that VTech Communications,
Inc. is voluntarily participating in an industry
program to collect and recycle these batteries
at the end of their useful lives, when taken out
of service within the United States and Canada.
The RBRC program provides a convenient
alternative to placing used nickel-metal hydride batteries into
the trash or municipal waste, which may be illegal in your area.
VTech’s participation in RBRC makes it easy for you to drop
off the spent battery at local retailers participating in the RBRC
program or at authorized VTech product service centers. Please
call
1 (800) 8 BATTERY® for information on Ni-MH battery recycling
and disposal bans/restrictions in your area. VTech’s involvement
in this program is part of its commitment to protecting our
environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered
trademarks of Call2recycle, Inc.
FCC, ACTA and IC regulations
FCC Part 15
NOTE: This equipment has been tested and found to comply
with the requirements for a Class B digital device under Part 15
of the Federal Communications Commission (FCC) rules. These
requirements are intended to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
WARNING: Changes or modifications to this equipment not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation. Privacy of communications may not be
ensured when using this telephone.
To ensure safety of users, the FCC/ISEDC has established
criteria for the amount of radio frequency energy that can
be safely absorbed by a user or bystander according to the
intended usage of the product. This product has been tested
and found to comply with the FCC/ISEDC criteria. The handset
may be safely held against the ear of the user. The telephone
base shall be installed and used such that parts of the user’s
body other than the hands are maintained at a distance of
approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian
requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and
with technical requirements adopted by the Administrative
Council for Terminal Attachments (ACTA). The label on the
back or bottom of this equipment contains, among other
things, a product identifier in the format US:AAAEQ##TXXXX.
This identifier must be provided to your telephone service
provider upon request.
The plug and jack used to connect this equipment to premises
wiring and the telephone network must comply with
applicable Part 68 rules and technical requirements adopted
by ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed to be connected to
a compatible modular jack that is also compliant. An RJ11 jack
should normally be used for connecting to a single line and an
RJ14 jack for two lines. See the installation instructions in the
user’s manual.
The Ringer Equivalence Number (REN) is used to determine
how many devices you may connect to your telephone line
and still have them ring when you are called. The REN for this
product is encoded as the 6th and 7th characters following the
US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In
most, but not all areas, the sum of all RENs should be five (5.0)
or less. For more information, please contact your telephone
service provider.
This equipment must not be used with Party Lines. If you have
specially wired alarm dialing equipment connected to your
telephone line, ensure the connection of this equipment
does not disable your alarm equipment. If you have questions
about what will disable alarm equipment, consult your
telephone service provider or a qualified installer.
If this equipment is malfunctioning, it must be unplugged
from the modular jack until the problem has been corrected.
Replacement to this telephone equipment can only be made
by the manufacturer or its authorized agents. For replacement
procedures, follow the instructions outlined under the
Limited warranty.
If this equipment is causing harm to the telephone network,
the telephone service provider may temporarily discontinue
your telephone service. The telephone service provider is
required to notify you before interrupting service. If advance
notice is not practical, you will be notified as soon as possible.
You will be given the opportunity to correct the problem and
the telephone service provider is required to inform you of
your right to file a complaint with the FCC. Your telephone
service provider may make changes in its facilities, equipment,
operation, or procedures that could affect the proper
functioning of this product. The telephone service provider is
required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset,
it is hearing aid compatible.
If this product has memory dialing locations, you may choose
to store emergency telephone numbers (e.g., police, fire,
medical) in these locations. If you do store or test emergency
numbers, please:
Remain on the line and briefly explain the reason for the call
before hanging up.
Perform such activities in off-peak hours, such as early
morning or late evening.
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including
interference that may cause undesired operation of the
device.
Privacy of communications may not be ensured when using
this telephone.
The term ‘’IC:‘’ before the certification/registration number
only signifies that the Industry Canada technical specifications
were met.
The Ringer Equivalence Number (REN) for this terminal
equipment is 0.1. The REN indicates the maximum number of
devices allowed to be connected to a telephone interface.
The termination of an interface may consist of any combination
of devices subject only to the requirement that the sum of the
RENs of all the devices not exceed five.
This product meets the applicable Innovation, Science and
Economic Development Canada technical specifications.
California energy commission
battery charging testing
instructions
This telephone is set up to comply with the energy-conserving
standards right out of the box. These instructions are intended
for California Energy Commission (CEC) compliance testing only.
When the CEC battery charging testing mode is activated, all
telephone functions, except battery charging, will be disabled.
To activate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power
outlet. Make sure all handsets are plugged with charged
batteries before proceeding.
2. While you press and hold /FIND HANDSET, plug the
telephone base power adapter back to the power outlet.
3. After about 20 seconds, when the IN USE light starts
flashing, release /FIND HANDSET and then press it again
within 2 seconds. When the phone successfully enters the
CEC battery charging testing mode, all handsets display To
register HS and See manual alternatively.
When the phone fails to enter this mode, repeat Step 1 through
Step 3 above.
To deactivate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power
outlet, and then plug it back in. Then the telephone base is
powered up as normal.
2. Place the handset in the telephone base to register it back.
The handset displays Registering...
The handset show Registered and you hear a beep when the
registration process completes. The registration process takes
about 60 seconds to complete.
Limited Warranty
What does this limited warranty cover?
The manufacturer of this VTech product, VTech
Communications, Inc. (“VTech”), warrants to the holder of a
valid proof of purchase (“Consumer” or “you”) that the Product
and all accessories provided by VTech in sales package
(“Product”) are free from material defects in material and
workmanship, pursuant to the following terms and conditions,
when installed and used normally and in accordance with
operating instructions. This limited warranty extends only to
the Consumer for Products purchased and used in the United
States of America and Canada.
What will VTech Communications do if the Product is not free
from material defects in materials and workmanship during
the limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service
representative will replace at VTech’s option, without charge,
a Materially Defective Product. If we choose to replace the
Product, we may replace it with a new or refurbished Product
of the same or similar design. VTech will return replacement
products to you in working condition. VTech will retain
defective parts, modules, or equipment. Replacement of
the Product, at VTech’s option, is your exclusive remedy. You
should expect the replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the product extends for
ONE (1) YEAR from date of purchase (90 days on products
purchased as Refurbished*). This limited warranty also applies
to replacement Products for a period of either (a) 90 days from
the date the replacement Product is shipped to you or (b)
the time remaining on the original one-year limited warranty
(90-day limited warranty on products that are purchased as
Refurbished*), whichever is longer.
*Refurbished products purchased from our online store carry a
90-day replacement warranty.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident,
shipping or other physical damage, improper installation,
abnormal operation or handling, neglect, inundation,
fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration
or modification by anyone other than an authorized
service representative of VTech; or
3. Product to the extent that the problem experienced is
caused by signal conditions, network reliability or cable
or antenna systems; or
4. Product to the extent that the problem is caused by use
with non-VTech electrical accessories; or
5. Product whose warranty/quality stickers, Product serial
number plates or electronic serial numbers have been
removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair
from outside the United States, or used for commercial
or institutional purposes (including but not limited to
Products used for rental purposes); or
7. Product returned without valid proof of purchase (see 2
below); or
8. Charges for installation or set up, adjustment of customer
controls, and installation or repair of systems outside the
unit.
How do you get warranty service?
To obtain warranty service in the United States of America,
please visit our website at www.vtechphones.com or call 1
(800) 595-9511 for instructions regarding where to return the
Product. In Canada, go to phones.vtechcanada.com or dial 1
(800) 267-7377.
NOTE: Before calling for service, please review the user’s
manual - a check of the Product’s controls and features may
save you a service call.
Except as provided by applicable law, you assume the risk
of loss or damage during transit and transportation and are
responsible for delivery or handling charges incurred in the
transport of Product(s) to the service location. VTech will
return replaced product under this limited warranty to you,
transportation, delivery or handling charges prepaid. VTech
assumes no risk for damage or loss of the Product in transit.
What must you return with the Product to get warranty
service?
1. Return the entire original package and contents including
the Product to the VTech service location along with a
description of the malfunction or difficulty;
2. Include “valid proof of purchase” (sales receipt)
identifying the Product purchased (Product model) and
the date of purchase or receipt; and
3. Provide your name, complete and correct mailing
address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement
between you and VTech. It supersedes all other written or
oral communications related to this product. VTech provides
no other warranties for this product. The warranty exclusively
describes all of VTech’s responsibilities regarding the product.
There are no other expressed warranties. No one is authorized
to make modifications to this warranty and you should not rely
on any such modification.
State Law Rights: This warranty gives you specific legal rights,
and you may also have other rights which vary from state to
state.
Limitations: Implied warranties, including those of fitness for a
particular purpose and merchantability (an unwritten warranty
that the product is fit for ordinary use) are limited to one year
from date of purchase. Some states do not allow limitations on
how long an implied warranty lasts, so the above limitation may
not apply to you.
In no event shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages (including,
but not limited to lost profits or revenue, inability to use the
product, or other associated equipment, the cost of substitute
equipment, and claims by third parties) resulting from the
use of this product. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of
purchase
Disclaimer and Limitation of
Liability
VTech Communications, Inc. and its suppliers assume no
responsibility for any damage or loss resulting from the use
of this user’s manual. VTech Communications, Inc. and its
suppliers assume no responsibility for any loss or claims by
third parties that may arise through the use of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road - Ste 555 Tigard,
OR 97223, United States
Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in
Canada
Technical specifications
Frequency
control
Crystal controlled PLL synthesizer
Transmit
frequency
Handset: 1921.536-1928.448 MHz
Telephone Base: 1921.536-1928.448
MHz
Channels DECT channel: 5
Nominal
effective range
Maximum power allowed by FCC
and IC. Actual operating range may
vary according to environmental
conditions at the time of use.
Power
requirement
Handset: 2.4V Ni-MH battery
Telephone base: DC 6V @ 0.4A
Charger: DC 6V @ 0.4A
Memory Phonebook: 50 memory locations;
up to 30 digits and 15 characters
Caller ID log: 50 memory locations;
up to 24 digits and 15 characters
Telephones identified with this logo have
reduced noise and interference when
used with most T-coil equipped hearing
aids and cochlear implants. The TIA-1083
Compliant Logo is a trademark of the
Telecommunications Industry Association.
Used under license.
T
Compatible with
Hearing Aid T-Coil
TIA-1083
The ENERGY STAR® program (www.
energystar.gov) recognizes and encourages
the use of products that save energy and
help protect our environment. We are proud
to mark this product with the ENERGY STAR®
label indicating it meets the latest energy
efficiency guidelines.
(US)
(CA)
-
1
-
2
VTech CS6719-16 Manuel utilisateur
- Catégorie
- Téléphones
- Taper
- Manuel utilisateur
dans d''autres langues
- English: VTech CS6719-16 User manual