Immersion LED DIsplay Lighting Elite Series Horizontal Guide d'installation

Marque: Immersion

Modèle: LED DIsplay Lighting Elite Series Horizontal

Taper: Guide d'installation

Refrigerated Horizontal Cases

Retrot and OEM

OPERATING TEMPERATURE

• Minimum is -20°C

• Maximum is 25°C

LED DRIVER COMPATIBILITY

This system is compatible with the following LED Drivers:

LED Driver Rated AC Input Voltage

GEPS6100NCCON-SY 120-240VAC, 60/50Hz

GELP24-100U-GLX 120-277VAC, 60/50Hz

GEPS24D-100U-NA 120-277VAC, 60/50Hz

GEPS24D-60U-GLX 120-277VAC, 60/50Hz

GELP24-60U-GL 120-277VAC, 60/50Hz

Eco Light Output

Canopy Lighting

12-INCH:

ELH1E1230CS/ELH1E1230CB

ELH1E1235CS/ELH1E1235CB

ELH1E1240CS/ELH1E1240CB

ELH1E1250CS/ELH1E1250CB

36-INCH:

ELH1E3630CS/ELH1E3630CB

ELH1E3635CS/ELH1E3635CB

ELH1E3640CS/ELH1E3640CB

ELH1E3650CS/ELH1E3650CB

48-INCH:

ELH1E4830CS/ELH1E4830CB

ELH1E4835CS/ELH1E4835CB

ELH1E4840CS/ELH1E4840CB

ELH1E4850CS/ELH1E4850CB

Eco Light Output

Undershelf Lighting

12-INCH:

ELH1E1230US/ELH1E1230UB

ELH1E1235US/ELH1E1235UB

ELH1E1240US/ELH1E1240UB

ELH1E1250US/ELH1E1250UB

36-INCH:

ELH1E3630US/ELH1E3630UB

ELH1E3635US/ELH1E3635UB

ELH1E3640US/ELH1E3640UB

ELH1E3650US/ELH1E3650UB

48-INCH:

ELH1E4830US/ELH1E4830UB

ELH1E4835US/ELH1E4835UB

ELH1E4840US/ELH1E4840UB

ELH1E4850US/ELH1E4850UB

Standard Light Output

Canopy Lighting

12-INCH:

ELH1S1230CS/ELH1S1230CB

ELH1S1235CS/ELH1S1235CB

ELH1S1240CS/ELH1S1240CB

ELH1S1250CS/ELH1S1250CB

36-INCH:

ELH1S3630CS/ELH1S3630CB

ELH1S3635CS/ELH1S3635CB

ELH1S3640CS/ELH1S3640CB

ELH1S3650CS/ELH1S3650CB

48-INCH:

ELH1S4830CS/ELH1S4830CB

ELH1S4835CS/ELH1S4835CB

ELH1S4840CS/ELH1S4840CB

ELH1S4850CS/ELH1S4850CB

Installation Guide

DISP120 | DOC-2002714

Elite

LED Display Lighting

WARNING / AVERTISSEMENT

Risk of electrical shock. Disconnect power before

servicing or installing product. LED Retrot Kit Installation

requires knowledge of luminaires electrical systems. If not

qualied, do not attempt installation. Contact a qualied

electrician. Install this kit only in the luminaires that have

the construction features and dimensions shown in the

photographs and/or drawings.

Risque de choc électrique. Couper le courant avant

de réparer ou installer le produit. LED Retrot Kit

d’installation nécessite la connaissance des systèmes

luminaires électriques. Si vous n’êtes pas qualié, ne

tentez pas l’installation. Contactez un électricien qualié.

Installez ce kit seulement dans les luminaires qui ont les

caractéristiques de construction et les dimensions gurant

sur les photographies et / ou des dessins.

CAUTION / ATTENTION

Risk of injury. While performing installations described,

gloves, safety glasses or goggles should be worn. Risque de

blessure. Lors de l'exécution des installations décrites, des

gants, des lunettes de sécurité ou des lunettes de protection

doivent être portées.

• Installation to be performed by factory trained service personnel only.

• For use inside a commercial refrigeration case with packaged foods only.

• Use this unit only in the manner intended by the manufacturer. If you have any

questions, contact the manufacturer.

• Before installing, servicing or cleaning unit, switch power off at the service

panel and follow appropriate lock out/tag out safety procedures.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS shown

throughout these instructions.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

LED.com

without notice. All values are design or typical values when measured under laboratory conditions.

Page 1 of 9

(Rev 06/21/23)

DISP120-LED-lmmersion-Elite-Horizontal-lnstall-Guide

ImmersionTM Elite Installation Guide

LED.com

without notice. All values are design or typical values when measured under laboratory conditions.

Page 2 of 9

(Rev 06/21/23)

DISP120-LED-lmmersion-Elite-Horizontal-lnstall-Guide

SKU Product Code Detailed Description

93155625 GE-JC24IN-66M-66F 24 Inch Jumper Cable with IP66 Male and IP66 Female Connector

93155627 GE-LC24IN-66F 24 Inch Leader Cable with IP66 Female Connector

93155628 GE-LC24IN-66M 24 Inch Leader Cable with IP66 Male Connector

Wire Stripper/Cutter

Screwdriver

Cordless drill with driver bit

Tools Required

Components Required

Cable Specications

6 7 8 9

Immersion Horizontal LED Light

Jumper cable with male and female connector

Leader cable with female connector

Leader cable with male connector

LED Driver

1 6

2 7

L-clip with thumbscrew

6-32 x 1/2" screws

UL approved 22-18 AWG (0.33-0.82 mm2) connectors

or in-line/IDC connectors.

Connector sealing cover ( SKU: 93155838)

Remove Existing Lighting Components

• For retrot only. If you are an OEM, please refer to the OEM Installation

Guide.

• Refer to manufacturing manual for refrigeration case to identify lighting

control circuits. Ensure that power is switched off at the service panel

for the lighting circuit. If a lighting power switch is not provided in the

refrigeration case, power removal can be performed at the main breaker

panel.

• Locate existing lighting components including ballasts, lampholders,

lamps, and lampguards in the refrigeration case for removal. Please

refer to refrigeration manual for any questions dealing with component

locations.

• Remove lamps, lampholder and lamp guards. Cut the wiring, making the

cut as close to the lampholder as possible. Do not remove wiring from

case as it will be utilized to attach the LED light. Dispose of components

per federal and local regulations.

• Locate ballast within system. The most common location is in the canopy

or on top of the case.

• Disconnect ballast input and output connectors. Cut the ballast

connector wires nearest to the connector and remove connector.

Unscrew the mounting screws that attach ballast and remove ballast.

Dispose of ballasts according to federal and local regulations. LED driver

installation will begin at Step 5 and Step 6.

• To install the LED light, rst identify the wiring for connection to the

LED driver. After removing the connector from ballast, leave the existing

ballast input and output wires for reconnection in a later step.

Fluorescent

Component

Location

Retrot Installation (for OEM install, proceed to Step 2)

Select Installation Position

Canopy

Undershelf

Nose

• Select installation position: Undershelf, Canopy or Nose

ImmersionTM Elite Installation Guide

LED.com

without notice. All values are design or typical values when measured under laboratory conditions.

Page 3 of 9

(Rev 06/21/23)

DISP120-LED-lmmersion-Elite-Horizontal-lnstall-Guide

WARNING / AVERTISSEMENT

Risk of re or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrot kit. Check for enclosed

wiring and components. / Risque de feu ou électrocution. Les pièces et câbles électriques risquent d’être endommagés lors du perçage des trous pour

l’installation du luminaire à DEL. Veuillez vérier si des câbles et composantes se trouvent derrière la paroi avant de percer.

To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. / Pour éviter l'endommager de câblage ou

l'abrasion, ne pas exposer le câblage aux bords de feuilles de métal ou d'autres objets tranchants.

Lamp and lamp holders

Ballast

1. Canopy

2. Top of case

B2 B1

• Remove each shelf and turn upside down on work surface.

• Thread LED Light wire through the large hole in selected mounting

clip and slide over the end of LED Light. Slightly tighten thumb screw.

Refer to Figure 1.

• Slide second mounting clip over opposite end of LED Light.

• With mounting clips still attached, place LED Light ush with shelf

edges, positioning it as far forward as possible while still concealing

LED Light from view. Refer to Figure 2.

• Install mounting clip to shelf with two #6 self-drilling pan headed

screws per mounting clip. Refer to Figure 3.

• Insert tension screw into both mounting clips and partially tighten

each screw into nut to enable the LED Light position to adjust. Refer to

Figure 4.

Install LED Lights into Undershelf Position

Shelf installation shown in gures at right.

Install LED Lights into Canopy

and Nose Position

Tighten thumb screw

Figure 4

Install mounting clip

Figure 3

• Thread LED Light wire through the large hole in selected mounting

clip and slide over the end of LED Light. Refer to Figure 1.

• Slide second mounting clip over opposite end of LED Light.

• With mounting clips still attached, place LED Light ush against

mounting surface, positioning it as far forward as possible while still

concealing LED Light from view. Refer to Figure 2.

• Install mounting clips to panel with two #6 self-drilling pan headed

screws per mounting clip. Refer to Figure 3.

• Insert thumb screw into one mounting clip and partially tighten screw

to enable the LED Light position to adjust. Refer to Figure 4.

Shelf

Position forward

Figure 2

Figure 1

Attach mounting clip

Connect Leader Cable

Figure 5

• Connect the leader cable to the the rst LED light in the run closest to

the power supply. Refer to Figure 5.

ImmersionTM Elite Installation Guide

LED.com

without notice. All values are design or typical values when measured under laboratory conditions.

Page 4 of 9

(Rev 06/21/23)

DISP120-LED-lmmersion-Elite-Horizontal-lnstall-Guide

WARNING / AVERTISSEMENT

Risk of electrical shock. Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do

not leave any other open holes in an enclosure of wiring or electric components.

Risque de choc électrique. Seuls les trous ouverts indiqués dans les photos et / ou les dessins peuvent être faites ou modiés à la suite du montage du

kit. Ne pas laisser autres trous ouverts dans l'enceinte du câblage électrique ou composants.

Leader cable

Connect Light Bars Together

Install End Cap

Connect Leader Cable

To Unmate Connectors

• Mate the male and female connectors of each adjacent light bar

while ensuring the connectors are oriented in the same direction.

• DO NOT attempt to mate upside down or otherwise exert

excessive force on the light bar connectors.

• Be sure that the retaining clip of the connectors are fully engaged

and locked together as indicated by a click.

• Attach jumper cables as needed to work around any obstacles,

corners or separations.

• DO NOT pull on the wires when un-mating the connectors.

• Install an end cap into the open connector on the last light bar in

the series.

• NOTE: If use leader cable with male connector (GE-LC24IN-66M)

connect driver and light bar right side female connector, ip the end

cap around and install it into into the open male connector on the

last light bar in the series.

• Connect the leader cable to the rst light bar in the run closest

to the power supply.

Continuous Run Connections (Optional)

ImmersionTM Elite Installation Guide

LED.com

without notice. All values are design or typical values when measured under laboratory conditions.

Page 5 of 9

(Rev 06/21/23)

DISP120-LED-lmmersion-Elite-Horizontal-lnstall-Guide

• Pushing the plug latch, grasp the connector at each end and

pull apart.

• DO NOT pull on the wires when unmating the connectors.

Last light bar

First light bar

Leader cable

Pull direction

Push here

Maximum LED Driver Loading Specications

Wiring Multiple LED Lights

LED Driver Loading Specications

Any combination of RH30 LED Lights may be loaded onto a power supply following these guidelines.

Add up total planned LED load watts per table below.

Up to 2 LED Lights may be connected in Series

DC Watts*

LED Driver

GELP24-60U-GL

GEPS24D-60U-GLX

Min. Load | Max. Load

LED Driver

GEPS6100NCCON-SY,

GELP24-100U-GLX

GEPS24D-100U-NA

Min. Load | Max. Load

Standard Canopy 4ft. 21.6 2 | 2 2 | 3

Standard Canopy 3ft. 15.6 2 | 3 3 | 5

Standard Canopy 1ft. 5.4 5 | 9 8 | 15

Eco Canopy 4 ft. 14.4 2 | 3 3 | 5

Eco Canopy 3 ft. 10.8 3 | 4 4 | 7

Eco Canopy 1 ft. 3.6 8 | 13 12 | 21

Eco Undershelf 4 ft. 5.8 5 | 8 8 | 14

Eco Undershelf 3 ft. 4.3 6 | 11 10 | 19

Eco Undershelf 1 ft. 1.44 18 | 35 29 | 57

* For typical in-situ DC power and actual system power consumption (AC Watts) see product technical guide.

Black

(line)

White

(neutral)

Mains InLED driver

LED Light

ImmersionTM Elite Installation Guide

LED.com

without notice. All values are design or typical values when measured under laboratory conditions.

Page 6 of 9

(Rev 06/21/23)

DISP120-LED-lmmersion-Elite-Horizontal-lnstall-Guide

WARNING / AVERTISSEMENT

Risk of electrical shock. Ensure that all connection points are sealed for damp location using the appropriate method per the NEC or

local electrical code.

Risque de choc électrique. S’assurer que les points de raccordements sont scellés pour emplacement humide en employant une

méthode permise par le NEC ou par le code électrique local.

CAUTION / ATTENTION

Risk of injury. Do not overload LED Driver. Do not exceed limits shown in “Maximum LED Driver Loading” table below.

Risque de blessure. Ne pas surcharger l'alimentation. Ne pas exéder les limites de la table ci-dessous: “Charges maximales pour les alimentations.”

Connecting a GEPS6100NCCON-SY Driver

ImmersionTM Elite Installation Guide

LED.com

without notice. All values are design or typical values when measured under laboratory conditions.

Page 7 of 9

(Rev 06/21/23)

DISP120-LED-lmmersion-Elite-Horizontal-lnstall-Guide

Input

AC line

Dimming

OPTIONAL:

Enable dimming

by cutting loop

Output LED

Occupancy

Sensor

GEPS6100NCCON-SY

Connect DC output

using 4-way

connector.

Connect DC output

using 4-way

connector.

Connect AC input using wire nuts. Connect DC output using wire nuts.

Ground

Molex

Connector

Molex Connector

Purple

Gray

Option Optionor or

• Make input and output connections according to diagrams below.

• Connection methods should be suitable for low temperature usage and standard cable.

• For non-dimming applications, cap the unused wires with 5/32” (4mm) twist on wire connectors.

• For dimming applications, cut the dimming loop on the driver output side and make connections to the occupancy sensor.

• CAUTION: DO NOT apply voltage or power to the switched control circuit – contact closure only.

• Other methods for automated control such as occupancy sensors that switch the AC power side on and off are not recommended

and will void the product warranty.

White (–)

Red stripe (+)

White (–)

Red stripe (+)

Wire Cavity Table

Molex 39-01-4046 (DC)

Cavity 1 - Output DC (+) (Red)

Cavity 2 - Output DC (-) (Black)

Cavity 3 - Dimming (Purple)

Cavity 4 - Dimming (Gray)

Wire Cavity Table

39-01-4030 (AC)

Cavity 1 - Line 1 (Black)

Cavity 2 - Earth Ground (Green)

Cavity 3 - Neutral or Line 2 (White)

B D

C D

Cap the Last LED Light

• Install an end cap into the open connector on the last LED light in the

series.

• NOTE: If use leader cable with male connector (GE-LC24IN-66M) connect

driver and light bar right side female connector, ip the end cap around

and install it into into the open male connector on the last light bar in the

series.

ImmersionTM Elite Installation Guide

LED.com

without notice. All values are design or typical values when measured under laboratory conditions.

Page 8 of 9

(Rev 06/21/23)

DISP120-LED-lmmersion-Elite-Horizontal-lnstall-Guide

Input

Output

LED

Ground

White (–)

Pink (–)

(–)

Red

stripe (+)

(+)

Dimming

Controller

Connecting a GELP24-60U-GL or GELP24-100U-GLX Driver

Connecting a GEPS24D-60U-GLX or GEPS24D-100U-NA Driver

• Make input and output connections according to diagrams below.

• Connection methods should be suitable for low temperature usage and standard cable.

• Make input and output connections according to diagrams below.

• Connection methods should be suitable for low temperature usage and standard cable.

Input

Output

LED

Ground

White (–)

Red stripe (+)

End cap

GELP24-60U-GL

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation.

This Class (A) RFLD complies with the Canadian standard ICES-005. Ce DEFR de la clase (A) est conforme a la NMB-005 du Canada.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference

to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

Cleaning Instructions

• The LED Light may be dusted as needed with a dry, clean, soft cloth.

• Do not use chemical cleaners on the system.

• Do not wipe with a soiled dishcloth or wet towel–these may leave a

residue that can damage the nish.

• Do not use scouring pads, powdered cleaning products, bleach or

cleaners containing bleach because these products can scratch and

damage the nish.

LED Light Positioning

• If installing in the undershelf position, reinstall shelves back into case.

• Clean away any debris from case.