Modern Forms WS-26214 Vander Mode d'emploi
- Taper
- Mode d'emploi
1
INSTALLATION INSTRUCTIONS
WS-26214
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov .2021
: To prevent electrical shock, ensure electricity has been turned o at the circuit breaker before beginning.
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
: Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
Wire Connector
Qty: 3pcs+1 Extra
Mounting Screw
Qty:1 Extra Plastic Anchor
Qty: 2pcs+1 Extra
Wood Screw
Qty: 2pcs+1 Extra
C
AB
Bottom Screw
Qty: 2pcs+1 Extra
D
Top Screw
Qty: 3pcs+1 Extra
EF
Support Column
Qty: 1pc
Allen Screw
Qty: 1pcs+1 Extra
Allen Wrench
Qty: 1pc
GHI
2
INSTALLATION INSTRUCTIONS
WS-26214
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2021
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
3. Remove the mounting screw (B) and back plate from the xture.
4. The lamp can switch between three color temperatures (2700K-3000K-3500K), which can be adjusted to your preference with the switch in
the canopy (Fig.3).
5. Remove the bottom screw ( C ) and top screw (D), fasten the bottom diuser between the xture and decorative frame using bottom screw
( C ),loose the allen screw (H) using allen wrench (I
6. Drill holes in the wall aligned with the key holes located in the mounting back plate and the support column of the decorative frame .
Secure the mounting back plate to the junction box using standard junction box screws that comes with the junction box, fasten it to the
wall using wood screw (E) .
Note (i) using any other non-original-manufacturer provided junction box screw may result in safety issue;
(ii) The side of the mounting plate marked “GND” must face out.
7. Connect the xture’s wires to junction box wires as shown in , making sure that all wire connectors () are secured. If your outlet box has
a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the back
plate using the GND screw provided. After wires are connected, tuck them carefully inside the junction box.
8. Insert the plastic anchor(F) and ax the support column (G) to the lower plastic anchor (F) using wood screw (E).
9. Secure xture to back plate with mounting screw (B) . Ensure the support column is aligned and inserted into the frame's lower support arm.
10. Place the fabric shade over the xture so it sits in the notch of the xture. Secure it with top diuser by fastening the top screw (D) .
11. Secure the frame’s lower support arm to the wall so it is ush by tightening the allen screw (H) using allen wrench (I).
3000K3500K
2700K
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 2 Wiring
Top screw
Top diffuser
(RPL-DIF-26214-01)
Junction Box
White Fabric Shade
(RPL-SHA-26214)
Decorative Frame
Bottom diffuser
(RPL-DIF-26214-02)
Mounting screw
Mounting Back plate
Plastic Anchor
Bottom screw
Wire Connector
Junction Box Screw
D
B
C
F
A
Switch
Wood Screw
E
Fixture
Allen Screw
Allen Wrench
Wood Screw
Support Column
G
I
H
E
Plastic Anchor
F
12
7/8
"
WS-26214 Mounting Back Plate
9
7/8
"
4
3/4
"
1
3/8
"1
3/4
"
-
1
-
2
Modern Forms WS-26214 Vander Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms WS-W24110 Maglev Mode d'emploi
-
-
-
-
-
-
-
-
-