WAC Lighting FM-95408 Mode d'emploi

Taper
Mode d'emploi
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
HARDWARE
To prevent electrical shock, ensure electricity has been turned o at the circuit breaker before beginning.
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by
dweLED could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the
manufacturer if any parts are damaged or missing.
: Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in
coastal areas clean all external surfaces of the xture once every two weeks with a wet cloth.
: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie.
Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec un
chion humide.
1
INSTALLATION INSTRUCTIONS
954-LED Flush Mount
FM-95408
A
B
Wire Connector
Qty: 3pcs+1 Extra
Mounting Screw
Qty: 1 Extra
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
Dec 2023
FIG. 3 Switch
7. Mount the xture against the mounting plate. Secure the xture using the mounting screws (B).
CONNECTING THE WIRES (Fig. 2)
6. Connect the xture’s input wires to the junction box wires as shown in Fig. 2 using wire connectors (A) provided. Ensure wire connectors
are secure. Connect the xture’s ground wire to the ground in the junction box; this will be either a green wire or a bare copper wire.
After xture is wired to house wires, tuck wires carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screws (B) from the xture, take down the mounting plate.
4. The lamp can switch between four color temperatures (2700K-3000K-3500K-4000K), which can be adjusted to your preference with
the switch in the canopy. (Fig.3). Set to desired color temperature.
Note: the switch comes with a detachable cover, Remove the cover prior to adjusting the color temperature, Fasten the cover after
adjustment is made.
5. Secure the mounting plate to the junction box using the screws provided with the junction box..
Note: (i) using any other non-original-manufacturer provided junction box screw may result in safety issue;
(ii) the side of the mounting back plate marked “GND” must face out.
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
COMPLETING THE INSTALLATION (Fig. 1)
FIG.1
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
2
Mounting Plate Dimensions
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
Dec 2023
INSTALLATION INSTRUCTIONS
954-LED Flush Mount
FM-95408
Junction Box
Wire Connector
A
Ground Wire
Junction Box Screw
Mounting Screw
B
Fixture
Mounting Plate
4CCT Switch
4000K 3500K 3000K 2700K
**V
1 3/4"
6 3/4"
1 3/8"
6 7/8"
8. To utilize 0-10V dimming feature connect the purple (dim+) and pink or gray (dim-) wires from the dimming module to controller.From the
dimming module connect the black (live) or white (neutral) wires to the power sources from the junction box and the black (output-) and
blue (output+) wires to the xture see g4 below.
(OPTIONAL) DIMMER WIRING (Fig. 4)
Note: Dimming module (Part# LDS065M010AFE-LO1) is required in order to utilize 0-10V dimming feature
Fig.4 Driver Wiring
Black - Live
White - Neutral
Purple - Dim+
Pink or Gray - Dim- Blue - Output+
Black- Output-
Dimming Module
Switch Cover
  • Page 1 1
  • Page 2 2

WAC Lighting FM-95408 Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues