Corega USB2-HUB7 Manuel utilisateur

Catégorie
Commutateurs réseau
Taper
Manuel utilisateur

Ce manuel convient également à

Warranty
Corega International warrants product for two years from date of purchase
against defects in materials and workmanship. This warranty does not
cover any defects caused by accident, misuse, fair wear and tear, neglect,
or an attempt at repair. This warranty is offered as an additional benefit
to the consumer’s statutory rights and does not affect these rights in
any way.
Corega International shall not be held responsible for any special,
incidental, or consequential damages resulting from any breach of
warranty, or under any other legal theory, including but not limited to lost
profit, downtime, damage to data stored in or used with Corega
International products.
Trademarks
Corega
TM
is a trademark of Corega Holdings KK., Japan.
Other trademarks, brand and product names are acknowledged as
trademarks of their respective holders. Information is subject to change
without notice.
All rights reserved.
617-00052-01
(GB) Warnings
ELECTRIC SHOCK HAZARD:
Install product in accordance with local and National Electrical Codes.
To de-energise equipment, disconnect the power cord.
(D) Warnhinweise
STROMSCHLAGGEFAHR:
Dieses Produkt muss entsprechend den örtlichen und nationalen
Elektrizitätsvorschriften installiert werden. Zum Abschalten der Ausrüstung
Stromkabel abziehen.
(I) Avvisi
RISCHIO DI SHOCK ELETTRICO:
Installare l'apparecchio in base alle normative elettriche locali e nazionali.
Per togliere l'alimentazione al dispositivo, scollegare il cavo relativo.
(E) Advertencias
PELIGRO DE ELECTROCUCIÓN:
Instale el producto de acuerdo con las recomendaciones de la normativa
sobre instalaciones eléctricas de su país. Para desactivar el equipo,
desconecte el cable de alimentación.
(F) Avertissements
RISQUE D'ÉLECTROCUTION:
Installez le produit conformément aux réglementations électriques
nationales et locales. Pour mettre l'équipement hors tension, débranchez le
cordon d'alimentation.
(FIN) Varoitukset
SÄHKÖISKUN VAARA:
Asenna tuote noudattaen paikallisia ja kansallisia säädöksia. Laitteen saa
jännitteettömäksi vain irroittamalla sähköjohdon.
(RUS) 
   :
     
   
.   
  .
 –    A.  
     . 
  , , 
  .
USB2-HUB7
7 PORT USB 2.0
HI-SPEED HUB
GET CONNECTED
HUBS • SWITCHES • ADAPTERS • WIRELESS LAN • USB • KVMs • MEDIA CONVERTERS • ROUTERS
ENGLISH: Pg 1-4
DEUTSCH: Pg 5-8
ITALIANO: Pg 9-12
ESPANOL: Pg 13-16
FRANCAIS: Pg 17-20
: Pg 21-24
ENGLISH
4
(7) Connecting Peripherals You may connect your USB peripheral to any of the downstream (type A) ports of the
hub. If you are installing a peripheral for the first time, you may need to install
drivers for the peripheral that should be supplied by the peripheral manufacturer.
(8) Congratulations, you have successfully completed this installation.
Indicators & Troubleshooting
LED Description
Pwr Off Power adapter not plugged into unit.
On (Red) Power applied
Operating Off No USB device attached
On (Green) USB device attached
Alarm Off Device operating
On (Amber) Device taking excess current
DEUTSCH
5
INSTALLATION
(1) Paketinhalt 1 x USB Hub
1 x Stromversorgung
1 x 2m USB Kabel
1 x Wand-Montage-Kit (2 Schrauben, 2Dübel)
1 x Installationsanleitung
Schnittstellen/Ports
7 x USB Typ A
1 x USB Typ B
1 x DC-Buchse für Stromkabel
LED-Anzeigen
Power (Strom) eine
Operating eine pro Port (7)
Alarm eine pro Port (7)
Abmessungen
177mm x 103mm x 30.5mm
Gewicht
220g
Temperatur
Betrieb: 0°C bis 40°C
Feuchtigkeit
Betrieb: 5-95%, nicht kondensierend
Leistungsaufnahme
17.5W
Externer Stromadapter
Ausgangsspannung 5VDC +/- 5%
Ausgangsstrom 4.0A
Maße (maximal)
80mm (H) x 55mm (B) x 55mm (T)
Länge des Niederspannungskabels: ca. 2m
(Die tatsächliche Größe des Stromadapters variiert nach Land.)
Ersatzteil-Artikelnummern
USA: COR-PSU-5V0/4A5/A US
UK: COR-PSU-5V0/4A5/A UK
Europa: COR-PSU-5V0/4A5/A EU
Australia: COR-PSU-5V0/4A5/A AU
Standards und Normgerechtigkeit
USB 2.0
USB 1.1
Behördliche Genehmigungen
FCC Class B
CE Class B
VCCI Class B
UL
cUL
Gost
Garantie
2 Jahre
TECHNISCHE SPEZIFIKATIONEN
7-Port-Hub
100% konform mit der USB 2.0 Hi-Speed-Spezifikation
LED-Anzeige für Port-Status und Gerätestrom
•Überstromerkennung und -sicherung
Nennstrom pro Port: max. 500mA
7 Downstream-USB-Ports (Typ A) und ein
Upstream-USB-Port (Typ B)
Kompatibel mit USB 1.1- und USB 2.0-Geräten
Merkmale
ESPANOL
13
INSTALACIÓN
(1) Contenido del paquete 1 x USB Hub
1 x Fuente de alimentación
1 x 2m USB Cable
1 x Kit montaje en pared (dos tornillos, dos tacos de plastico)
1 x Guía de instalación
Interfaces
7 x Puerto USB, conector tipo A
1 x Puerto USB, conector tipo B
1 x Conexión para alimentación DC
LED
Alimentación (power) uno
Operating uno por puerto (7)
Alarm uno por puerto (7)
Dimensiones
177mm x 103mm x 30.5mm (Máx)
Peso
220g
Temperatura
Operación entre 0ºC y 40ºC
Humedad
Operación entre el 5-95% volumen de humedad, sin condensación
Consumo
17.5W
Fuente de alimentación externa
Tensión de salida 5V DC +/- 5%
Corriente 4.0A
Dimensiones (máximas)
80mm (Alto) x 55mm (Ancho) x 55mm (Fondo)
Longitud del cable electrico: 2m (aproximados)
(El tamaño de la fuente de alimentación varía según el pais)
Referencia de pedido (P/N)
USA: COR-PSU-5V0/4A5/A US
UK: COR-PSU-5V0/4A5/A UK
Europe: COR-PSU-5V0/4A5/A EU
Australia: COR-PSU-5V0/4A5/A AU
Estándares
USB 2.0
USB 1.1
Certificaciones
FCC Class B
CE Class B
VCCI Class B
UL
cUL
Gost
Garantía
2 años
HOJA TÉCNICA
Hub de 7 puertos
100% compatible con la especificación de máxima
velocidad USB 2.0 Hi-Speed USB
Indicadores de estado de los puertos y LED indicador de
alimentación eléctrica
Detección y protección contra sobrecargas de corriente
Corriente máxima de 500 mA por puerto
7 puertos USB Tipo A descendentes y un puerto USB
Tipo B ascendente
Compatible con dispositivos USB 1.1 y USB 2.0
Características
ESPANOL
16
(7) Conexión de periféricos Puede conectar perifericos USB a cualquier puerto (tipo A) del hub. Si está instalando
un dispositivo periférico por primera vez, es posible que tenga que instalar los
controladores (drivers) correspondientes, que deben ser facilitados por el fabricante
del periférico.
(8) Enhorabuena! Ya tiene instalado correctamente el conversor de medio Corega.
Indicadores y resolución de problemas
LED Indicador Descripción
Pwr Off No hay alimentación eléctrica, o el adaptador de alimentación no está
conectado a la unidad (Alimentación por bus).
On (Rojo) Alimentación eléctrica conectada.
Operating Off No hay ningún dispositivo USB conectado.
On (Verde) Dispositivo USB conectado.
Alarm Off Equipo funcionando
On (Ambar) Equipo con exceso de corriente
FRANCAIS
17
(1) Contenu du carton 1 x USB Concentrateur
1 x Bloc dalimentation
1 x 2m USB Câble
1 x Kit pour monter au mûr (deux vis, deux prises murales en plastique)
1 x Guide dinstallation
Ports d’interface
7 x USB type A connecteur
1 x USB type B connecteur
1 x Connecteur DC
LED indicateurs
Alimentation une
Operating une par port (7)
Alarm une par port (7)
Dimensions
177mm x 103mm x 30.5mm (Max)
Poids
220g
Température
Fonctionnement normal entre 0°C et 40°C
Humidité
Fonctionnement normal entre 5-95% dhumidité, sans condensation
Consommation de l’alimentation
17.5W
Adaptateur d’alimentation externe
Voltage 5V DC +/- 5%
Courant 4.0A
Dimensions (maximum)
80mm (H) x 55mm (W) x 55mm (D)
Longueur du câble de courant bas: 2m (approx)
(La taille de ladaptateur dalimentation dépend du pays)
Numéros de commande
USA: COR-PSU-5V0/4A5/A US
UK: COR-PSU-5V0/4A5/A UK
Europe: COR-PSU-5V0/4A5/A EU
Australia: COR-PSU-5V0/4A5/A AU
Conformité de normes
USB 2.0
USB 1.1
Approbations
FCC Class B
CE Class B
VCCI Class B
UL
cUL
Gost
Garantie
2 ans
TECHNICAL SPECIFICATIONS
Concentrateur à 7 ports
100% conforme à la spécification Hi-Speed USB 2.0
Voyants d'état de port et d'alimentation.
Détection et protection contre les surcharges de courant
Courant maximum de 500 mA par port
7 ports de type A USB en aval et un port de type USB
en amont
Compatible avec les périphériques USB 1.1 et USB 2.0
Caractéristiques
FRANCAIS
18
(2) Choix de l'emplacement L'emplacement choisi doit respecter les caractéristiques de température et
d'humidité de fonctionnement décrites à la section Caractéristiques techniques.Veillez à
prévoir un dégagement de 50 mm au moins tout autour du USB concentrateur pour
permettre une ventilation adéquate.
(2A) Option de montage au mur Clipper les deux attaches plastique du kit de montage mural sur la base du
concentrateur USB. Utilisez une mèche de 6 mm. Installez le commutateur au mur à
l'aide des vis et des fiches fournies.
1.5mm
50mm
FRANCAIS
19
(3) Pilotes logiciels Tous les pilotes de ce concentrateur USB sont disponibles sous Windows XP, 2000, Me,
98SE et 98 ou MacOS 9.0 et versions plus récentes. Si vous utilisez un autre système,
vérifiez les dernières mises à jour de pilotes sur le site de support de Corega.
www.corega-international.com
(4) Mise sous tension Branchez l'adaptateur secteur externe sur une prise appropriée et insérez le
connecteur basse tension dans la prise d'alimentation à l'arrière du concentrateur.
(5) Vérification du voyant Vérifiez que le voyant d'alimentation (PWR) s'allume.
d'alimentation
(6) Connexion à l'ordinateur Connectez le concentrateur USB au port USB de votre ordinateur à l'aide du câble USB
fourni. Le nouveau matériel est détecté automatiquement par l'ordinateur lors de son
installation initiale. Suivez l'Assistant d'installation de nouveau matériel. Il vous est
demandé dans certains cas de redémarrer votre ordinateur. Ne retirez pas le
concentrateur USB avant de le faire.
FRANCAIS
20
(7) Connexion de périphériques Vous pouvez connecter des périphériques USB à n'importe port en aval (de type A) du
concentrateur. Lors de l'installation initiale d'un périphérique, il est parfois nécessaire
d'installer les pilotes correspondants qui sont normalement fournis par son
constructeur.
(8) Félicitations : vous avez correctement installé votre USB Hub Corega.
Voyants et dépannage
LED Indicateurs Description
Pwr Éteint Pas d'alimentation ou adaptateur secteur non connecté à l'unité
(alimentation bus)
Allumé (rouge) Alimentation appliquée
Operating Éteint Pas de périphérique USB connecté
Allumé (vert) Périphérique USB connecté
Alarm Éteint Appareil en opération
Allumé (orange) Appareil utilisant un excès de courant

23
(3)        USB
   Windows XP, 2000, Me, 98SE 98, MacOS 9.0
    .    
,    Corega
–     .
www.corega-international.com
(4)        
      
.
(5)  ,     
 (PWR).
 
(6)     USB  USB   
    USB.  
    .
    .  
      USB
 .
26
THIS PAGE IS INTENTIONALLY LEFT BLANK
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Corega USB2-HUB7 Manuel utilisateur

Catégorie
Commutateurs réseau
Taper
Manuel utilisateur
Ce manuel convient également à