sunjoe SPX3160P-SJG Le manuel du propriétaire

Marque: sunjoe

Modèle: SPX3160P-SJG

Catégorie: Nettoyeurs haute pression

Taper: Le manuel du propriétaire

SAVE THESE INSTRUCTIONS

A Division of Snow Joe®, LLC

OPERATOR’S MANUAL

Original instructions.

Form No. SJ-SPX3160P-SJG-880E-M-FTY

Model SPX3160P-SJG

11A ELECTRIC GO ANYWHERE PRESSURE WASHER

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

mWARNING! This indicates a hazardous situation, which,

if not avoided, could result in death or serious injury.

mCAUTION! This indicates a hazardous situation, which,

if not avoided, could result in minor or moderate injury.

mDANGER! This indicates a hazardous situation, which,

if not avoided, will result in death or serious injury.

General Safety

mWARNING! This appliance is not intended for use

by children or by unassisted, unsupervised persons whose

physical, sensory, or mental capabilities prevent them from

using it safely. Children should be supervised to ensure that

they do not play with the appliance.

Before starting up your machine, please check it carefully for

any defects. If you nd any, do not start up your machine.

Contact your authorized Snow Joe® + Sun Joe® dealer or

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

mWARNING! When using the pressure washer, basic

safety precautions should always be followed to reduce the

risk of re, electric shock, and personal injury. These include:

• Know your product – Know how to stop the machine and

bleed pressure quickly. Thoroughly familiarize yourself with

the controls.

• Keep bystanders away – All visitors and pets should be

kept a safe distance away from the work area.

• Use the right product – Do not use this machine for any

job except that for which it is intended.

• Dress properly – Do not wear loose clothing or jewelry.

They can get caught in moving parts. Protective rubber

gloves and non-slip footwear are recommended when

working outdoors.

• CAUTION! – Exercise caution to avoid slipping or falling.

Wear protective footwear that will protect your feet and

improve your footing on slippery surfaces.

• Stay alert – Watch what you are doing. Use common

sense. Do not operate the pressure washer when you are

tired, or under the inuence of alcohol or drugs.

• Do not overreach – Keep proper footing and balance at

all times.

• Avoid unintentional starting – Do not carry a plugged-

in machine with your nger on the trigger. Make sure the

switch is o before plugging in the machine.

• Do not abuse the cord – Never carry the machine by the

cord or yank the cord to disconnect it from the receptacle.

Keep the cord away from heat, oil, and sharp edges.

• Use safety glasses – Also use safety footwear, snug-

tting clothing, protective gloves, and hearing and head

protection.

• Check the water temperature – This pressure washer is not

meant to pump hot water. NEVER connect it to a hot water

supply as it will signicantly reduce the life of the pump.

• Store indoors – NEVER store the pressure washer

outdoors or where it could freeze. The pump could be

seriously damaged.

• Ground Fault Circuit Interrupter (GFCI) – GFCI protection

should be provided on the circuits or outlets to be used

for this pressure washer. Receptacles are available having

built-in GFCI protection and may be used for this measure

of safety.

• Inspect electrical cables – The insulation of the power

cord should be perfectly intact. If the power cord is

damaged or shows any signs of wear or tear, do not use

the pressure washer. Contact your authorized Snow Joe® +

Sun Joe® dealer or call the Snow Joe® + Sun Joe® customer

service center at 1-866-SNOWJOE (1-866-766-9563).

mWARNING! Do not use this appliance without reading

this instruction manual.

mWARNING! This appliance has been designed for

use with cleaning agents that are recommended by the

manufacturer. The use of other cleaning agents or chemicals

may adversely aect the safety of the appliance.

mWARNING! Do not use the appliance within range

of other people unless they are wearing protective clothing.

mWARNING! High-pressure jets can be dangerous if

subject to misuse. The jet must not be directed at persons,

pets, live electrical equipment, or the appliance itself.

• Do not direct the jet at yourself or others in order to clean

clothes or footwear.

• Risk of explosion – Do not spray ammable liquids.

• Risk of injection or injury to persons – Never direct

discharge stream at people, pets, or electrical devices.

• Disconnect the tool – Disconnect from the electrical power

supply before performing any maintenance task.

• Keep children away – This high-pressure electric

power washer must not be used by children or untrained

personnel.

• To ensure appliance safety, use only original replacement

parts from the manufacturer or those approved by the

manufacturer.

mWARNING! Water that has owed through backow

preventers is considered to be non-potable.

mWARNING! During cleaning, maintenance, or when

replacing parts, disconnect the machine from its power source

by removing the plug from the socket outlet.

mWARNING! High-pressure hoses, ttings, and

couplings are important for the safe operation of the appliance.

Use only hoses, ttings, and couplings recommended by the

manufacturer.

• Check for damaged parts – Do not use the appliance if

the supply cord or other important parts of the appliance

are damaged (e.g. safety devices, high-pressure hoses,

trigger gun).

• This high-pressure electric power washer must not be used

at temperatures below 32ºF (0°C).

mWARNING! Power cords on drums should always be

completely unwound to prevent the cord from overheating.

• Power cord connections should be kept dry and o the

ground.

• If the power cord is damaged, do not use the appliance.

Contact your authorized Snow Joe® + Sun Joe® dealer or

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

• Keep the machine on a stable, at surface during operation,

handling, transportation, and storage. Sudden overturn of

the machine can cause bodily injury.

• In the event of an accident or breakdown, switch o the

machine immediately. (If contact with detergent occurs,

rinse with an abundance of clean water.)

Electrical Safety

ATTENTION: If there are problems with the electrical

MAINS, short voltage drops may appear when starting the

equipment. This can, in turn, inuence other equipment

(e.g. cause a lamp to blink). If the MAINS-IMPEDANCE Zmax

< 0.335 OHM, such disturbances are not expected. (If you

require assistance, contact your local supply authority for

further information.)

mWARNING! Electrical Shock Hazard – Before starting

up your machine, please check it carefully for any defects.

If you nd any, do not start up your machine. Contact your

authorized Snow Joe® + Sun Joe® dealer or call the Snow Joe®

+ Sun Joe® customer service center at 1-866-SNOWJOE

(1-866-766-9563).

The following should be observed when connecting the

high-pressure electric power washer to the electric supply:

• The electric supply connection should be performed by a

qualied person.

• The electric supply to this appliance should include either

a residual current device that will interrupt the supply if the

leakage current to the earth exceeds 30 mA for 30 ms or a

device that will interrupt the earth circuit (GFCI).

IMPORTANT: Only use water without any impurities.

If there is a risk of running sand into the inlet water (i.e. from

your own well), an additional lter should be installed.

Servicing of Double-Insulated Appliance

In a double-insulated appliance, two systems of insulation

are provided instead of grounding. No grounding means is

provided on a double-insulated appliance, nor should a means

for grounding be added to the appliance. Servicing a double-

insulated appliance requires extreme care and knowledge

of the system, and should be performed only by qualied

service personnel at an authorized Snow Joe® + Sun Joe®

dealer. Replacement parts for a double-insulated appliance

must be identical to the parts they replace. A double-insulated

appliance is marked with the words “Double Insulation” or

“Double Insulated.” The symbol (square within a square)

may also be marked on the appliance.

Safety devices

The unloader valve can reduce pressure if it exceeds preset

values. The spray gun features a locking device. When the lock

is activated, the spray gun cannot be operated.

1. Thermal sensor – A thermal sensor protects the motor

against overloading. The machine will restart after a few

minutes when the thermal sensor has cooled.

2. Ground fault circuit interrupter (GFCI) protection – A

GFCI should be provided on the circuit(s) or outlet(s) to be

used for this pressure washer. Receptacles are available

having built-in GFCI protection and may be used for this

measure of safety.

3. It is not recommended to use an extension cord with this

pressure washer. The unit comes standard with a 35 ft

GFCI power cable. Using an extension cord may cause

a drop in line voltage, resulting in loss of power and

overheating.

mWARNING! To reduce the risk of electric shock, this

appliance has a polarized plug (i.e. one blade is wider than the

other). The appliance plug will t into a polarized outlet only

one way.

4. Do not abuse the cord. Never pull the pressure washer

by the cord or yank the cord to disconnect it from the

receptacle. Keep the cord away from heat, oil, and

sharp edges.

mWARNING! To reduce the risk of electrocution, keep

all connections dry and o the ground. Do not plug with wet

hands.

Risk of electrocution

• Inspect cord before using.

• Do not use if cord is damaged.

• Keep all connections dry and o the ground.

• Do not touch plug with wet hands.

• Keep cord away from heat and sharp edges.

• Do not spray electrical apparatus and wiring.

Risk of explosion

• Do not spray ammable liquids.

• Do not use acids, bases, solvents, or any ammable

material in this product. These substances can cause

physical injuries to the operator and irreversible damage to

the machine.

Additional safety instructions

• High-pressure: keep clear of nozzle.

• Injection hazard: equipment can cause serious injury if the

spray penetrates the skin.

• Do not point the gun at anyone or at any part of the body.

• In case of skin penetration, seek medical aid immediately.

• Before servicing, cleaning, or removing any parts, shut o

the power and relieve pressure.

• This machine is not suitable for connection to the potable

water mains.

Product Description

Purpose

• This high-pressure electric power washer is intended for

residential use only. It is designed for light-to-medium duty

cleaning jobs on boats, motorcycles, RVs, ATVs, trailers,

decks, barbecues, siding, patio furniture, and more.

Areas of application

• Never use the machine in potentially explosive areas under

any circumstances!

• The operating temperature must be between 32ºF (0ºC) and

104ºF (40ºC).

• The machine consists of an assembly with a pump, which

is encased in a shock-absorbing housing. To provide the

operator with an optimal working position, the machine is

equipped with a spray wand and a non-slip handle grip,

whose shape and conguration comply with applicable

regulations.

• Do not cover or modify the spray wand or the spray nozzle

in any way.

• The high-pressure electric power washer is designed to be

used with cold or lukewarm water; higher temperatures can

damage the pump.

• Do not use water that is dirty, gritty, or contains any

chemical products, as such impurities could impair

operation and shorten the life of the machine.

Safety Symbols

The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all

instructions on the machine before attempting to assemble and operate.

To reduce the risk of injury, user

must keep all bystanders at least

49 ft (15 m) away.

Always keep the power cable

away from heat sources, oils, or

sharp edges. Immediately remove

plug from the mains if the cable is

damaged, frayed, or entangled.

READ THE OPERATOR'S

MANUAL(S) – Read, understand,

and follow all instructions in the

user manual(s) before attempting

to assemble and operate.

SAFETY ALERT – Indicates a

precaution, a warning, or a danger.

WEAR EYE AND HEARING

PROTECTION – For protection

against injury, wear ear defenders

and safety goggles.

Double Insulation – When servicing, use only identical replacement parts.

WARNING! Do not expose the

unit to rain or wet conditions.

Keep dry.

Machine not suitable for connection

to the potable water mains.

WARNING! Electrical shock hazard.

WARNING! Turn the machine OFF

and disconnect it from the power

supply before inspecting, cleaning,

changing accessories, or conducting

any other maintenance task.

Symbols SymbolsDescriptions Descriptions

Wear non-slip footwear that will

protect your feet and improve your

footing on slippery surfaces.

Wear safety gloves during

use to protect hands.

Store indoors. Never store the

pressure washer outdoors.

If the pump freezes, permanent

damage may result.

Technical Data

Rated Voltage ........................................................120V ~ 60 Hz

Motor ..............................................................................11-amp

Max Water Inlet Temperature ...................................104ºF/40ºC

Max Water Inlet Pressure ..............................................0.7 MPa

Hose Length ............................................................... 20 ft (6 m)

Power Cord Length ............................................... 35 ft (10.7 m)

Adjustable Spray Nozzle ............................................. 0º to 45º

Foam Cannon Capacity .......................................10  oz (0.3 L)

Rated Pressure ............................................................. 1150 PSI

Rated Flow ..................................................1.1 GPM (4.2 L/min)

Net Weight ........................................................ 11.9 lbs (5.4 kg)

1. Trigger gun

2. Safety lock

3. Trigger

4. On/O switch

5. Foam-volume knob

6. Foam spray nozzle

7. Power cord with GFCI

FRONT BACK

Know Your Electric Pressure Washer

Read the owner’s manual and safety rules carefully before operating the pressure washer. Compare the illustration below to the

pressure washer in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for

future reference.

8. Garden hose adapter

(Female coupler)

9. Foam cannon bottle

10. Spray wand holder

11. Spray wand assembly

12. Water outlet

13. Adjustable spray wand nozzle

14. Caster wheel (2)

15. Velcro band

16. Wheel (2)

17. Spray wand

18. Trigger gun holder

19. High-pressure hose

20. Needle clean-out tool

21. Wheel + rim brush

22. Utility brush

23. Rotary brush

Unpacking

Carton Contents

• Electric pressure washer

• Trigger gun

• Caster wheel (2)

• Wheel (2)

• Spray wand

• Spray wand assembly

• Foam cannon

• High-pressure hose

• Garden hose adapter (female coupler)

• Needle clean-out tool

• Manual with registration card

1. Carefully remove the pressure washer and check to see

that all of the above items are supplied.

2. Inspect the product carefully to make sure no breakage or

damage occurred during shipping. If you nd damaged or

missing parts, DO NOT return the unit to the store. Please

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

NOTE: Do not discard the shipping carton and packaging

materials until you are ready to use your new electric

pressure washer. The packaging is made of recyclable

materials. Properly dispose of these materials in

accordance with local regulations.

IMPORTANT! The equipment and packaging materials are

not toys. Do not let children play with plastic bags, foils,

or small parts. These items can be swallowed and pose a

suocation risk!

mWARNING! Do not connect to power supply until

assembly is complete. Failure to comply could result in

accidental starting and possible serious personal injury.

Assembly

Spray Gun Assembly

1. Fit the two pieces of the spray wand assembly together

and rotate until they are completely locked (Fig. 1).

2. Fit the spray wand assembly into the gun and turn the

rotatable end-piece of the wand until the two parts are

completely locked (Fig. 2).

Installing Wheels

1. Install the caster wheels onto the front of the pressure

washer by inserting them into the two holes on the bottom

of the housing (Fig. 3). Press wheels down rmly to

secure.

Fig. 1

RELEASE

Spray wand assembly

Trigger gun

Fig. 2

Fig. 3

Caster wheels

2. Insert the larger back wheels into the two holes on either

side of the pressure washer housing (Fig. 4).

Connect the Spray Gun to

the Pressure Washer

1. Connect the quick-connect end of the high-pressure hose

to the trigger gun (Fig. 5). You will hear a click when it

snaps into place. To release the high-pressure hose from

the trigger gun, push the release button on the trigger gun.

2. Connect the other end of the high-pressure hose to

the water outlet on the pressure washer (Fig. 6). First,

push the high-pressure hose end completely onto the

high-pressure water outlet, then screw it on clockwise.

mWARNING! Keep hose away from sharp objects.

Bursting hoses may cause injury. Examine hoses regularly and

replace if damaged. Do not attempt to mend a damaged hose.

3. Connect the garden hose adapter (female coupler) to the

water inlet of the pressure washer, then thread your garden

hose (male end) into the garden hose adapter

(Figs. 7 – 8). The garden hose must have an internal

diameter of at least 13 mm (1/2 in.) and must be reinforced.

The water supply must be at least equal to the washer

delivery capacity.

NOTE: The machine is not suitable for connection to the

potable water main.

Fig. 4

Back wheels

RELEASE

Push to release

Trigger gun

Fig. 5

High-pressure hose

Fig. 6

Water outlet

High-pressure hose

Fig. 7

Water inlet

Garden hose

adapter

4. Attach garden hose to water supply (Fig. 9).

mWARNING! Do not connect to potable water system.

mWARNING! If connection is made to a potable water

system, the system shall be protected against backow.

mWARNING! The intake water temperature must

not exceed 104ºF/40ºC. The water supply must not exceed

0.7 MPa.

mCAUTION! The washer must only be used with clean

water; use of unltered water containing corrosive chemicals

will damage the washer.

mCAUTION! To prevent damage to the appliance, do not

allow it to operate dry. Before starting the appliance, make

sure that it has a proper and stable supply of water.

5. Make sure the motor switch is pushed to the OFF (0)

position before plugging the unit into the power outlet.

Operation

IMPORTANT! This pressure washer is equipped with a

micro-switch sensitive to water ow. This Total Stop System

(TSS) senses water ow in the pump. When the trigger is

released, water stops owing through the pump. The TSS then

automatically turns the motor o to protect the pump from

overheating, thus saving energy and prolonging pump life.

1. Check that the electrical supply voltage and frequency

(Volt/Hz) correspond to those specied on the pressure

washer rating plate. If the power supply is correct, you

may now plug the pressure washer into the power outlet

(Fig. 10).

NOTE: The GFCI may need to be reset when rst plugged

into the electric outlet. Press the "Reset" button until the

power light indicator on the GFCI illuminates.

2. Position the washer as CLOSE as possible to the

water supply.

3. The washer must be used on a secure and stable surface

in a standing, upright position (Fig. 11).

4. Turn the water supply tap on completely.

Fig. 8

Garden hose

Fig. 9

Connect to water supply

Garden hose

RESET

TEST

Fig. 10

GFCI

Power light

indicator

Reset

Fig. 11

5. Unlock the safety lock, then press the trigger for a few

seconds until the water ow is steady. Operating the

pressure washer in this manner will allow air to escape and

discharge residual pressure in the hose (Fig. 12). Release

the trigger after all residual pressure is discharged.

6. Keeping the trigger pressed, push the switch to the ON (I)

position to start the pressure washer (Fig. 13).

7. When re-starting the motor, always keep the trigger

pressed.

NOTE: The motor only runs when the trigger is depressed

and shuts o when the trigger is released.

Using the Adjustable Spray Wand

mWARNING! High-pressure jets can be dangerous if

subject to misuse. The jet must not be directed at persons,

pets, live electrical equipment, or the appliance itself.

1. The washer is equipped with an adjustable nozzle.

2. The nozzle tip can be adjusted from pencil spray to fan

spray by turning the nozzle tip adjustment knob (Fig. 14).

mWARNING! Do not adjust the nozzle while the trigger

is squeezed. Failure to do so could result in damage.

Working with Detergent

When cleaning with the pressure washer, some cleaning tasks

can be solved with water alone, but for most tasks, cleaning

with detergent allows for more eective dirt removal.

For additional cleaning power, the unit comes equipped with a

foam cannon.

mWARNING! Use only detergents specically designed

for use with pressure washers, such as Sun Joe® HOUSE +

DECK WASH (SPX-HDC1G), Sun Joe® SNOW FOAM AUTO

WASH (SPX-FCS1G), or Sun Joe® HEAVY DUTY CLEANER

(SPX-APC1G). DO NOT USE household detergents, acids,

alkaline solutions, bleaches, solvents, ammable material, or

industrial-grade solutions. These could damage the pressure

washer. Many detergents may require mixing prior to use.

Prepare the cleaning solution as instructed on the solution

bottle.

1. Remove the foam spray nozzle, and ll the foam cannon

bottle with detergent designed specically for use with

pressure washers (Fig. 15).

RELEASE

Fig. 12

Trigger

Safety lock

Fig. 13

On/O

switch

Fig. 14 Fan spray

Pencil spray

Nozzle tip

adjustment knob

Nozzle tip

Fig. 15

Foam cannon bottle

Pressure washer

detergent

Foam Spray

Nozzle

2. Recap the foam cannon bottle, and attach it to the trigger

gun via the spray wand assembly. Using the locking lugs,

twist clockwise to lock each component in place (Fig. 16).

3. The foam cannon bottle is equipped with a foam-volume

knob. Follow the instructions as shown to use the foam-

volume knob (Fig. 17).

4. Apply detergent from the bottom to the top of the dry

surface to be cleaned. Applying detergent in this manner

will dissolve dirt most eectively.

NOTE: Wetting the surface rst is not recommended as it

dilutes the detergent and reduces its cleaning ability.

mCAUTION! Always test the detergent in an

inconspicuous area before use.

5. Allow the detergent to remain on the surface for a short

time before rinsing with the pressure washer. Do not allow

the detergent to dry on the surface.

mCAUTION! Damage may occur to painted surfaces if

the detergent is allowed to dry on the surface. Wash and rinse

a small section at a time. Avoid working on hot surfaces or in

direct sunlight.

6. Rinse with clean water. When working on a vertical

surface, wash from the bottom up, then rinse from the top

down to avoid streaking. Hold the nozzle 6-8 inches away

from the work surface at a 45° angle.

mIMPORTANT! NEVER USE:

• Bleach, chlorine products, and other corrosive chemicals

• Liquids containing solvents (e.g. paint thinners, gasoline,

oils)

• Tri-sodium phosphate products

• Ammonia products

• Acid-based products

These chemicals will harm the unit and will damage the

cleaning surface.

Using the Feather Bristle Pressure

Washer Utility Brush

The Sun Joe® feather bristle pressure washer utility brush

safely cleans painted, topcoat, and delicate surfaces.

Compatible with all Sun Joe® SPX series pressure washers.

1. If not already done, detach your spray wand from your

trigger gun.

2. Take the utility brush and align the two tabs with the inside

of the trigger gun (Fig. 18).

Fig. 18

Locking tab

Utility brush

3. Once aligned, push the utility brush into the trigger gun,

twist counterclockwise to lock into place.

Using the Wheel + Rim Brush

The Sun Joe® wheel + rim brush safely cleans wheels and

rims. Compatible with all Sun Joe® SPX series pressure

washers.

1. Disconnect the spray wand from the trigger gun by

pressing it in rmly and twisting clockwise until the 2

locking tabs of the lance can be removed from the slot.

2. Take the wheel + rim brush and align the two tabs with the

inside of the trigger gun (Fig. 19).

Fig. 16

Foamer cannon bottle

Trigger gun

Spray wand assembly

Locking

lugs

Fig. 17

Foam-volume

knob

3. Once aligned, push the wheel + rim brush into the trigger

gun, twist counterclockwise to lock into place.

Fig. 19

Press the shaft inside

Twist the shaft as shown

Using the Rotating Surface Cleaner

The Sun Joe® rotary brush safely cleans painted, topcoat,

and delicate surfaces. Compatible with all Sun Joe® SPX

series pressure washers.

1. Disconnect the spray wand from the trigger gun by

pressing it in rmly and twisting clockwise until the 2

locking tabs of the lance can be removed from the slot.

2. Take the rotary brush and align the two tabs with the

inside of the trigger gun (Fig. 20).

3. Once aligned, push the rotary brush into the trigger gun,

twist counterclockwise to lock into place.

Fig. 20

Press the shaft inside

Twist the shaft as shown

Shutting down

1. Push the switch to the OFF (0) position and unplug the

power cord from the outlet.

2. Turn o the water source.

3. Hold the trigger to release water pressure.

4. Disconnect the garden hose from the water inlet on

the unit.

5. Disconnect the high-pressure hose connection on the

trigger gun handle.

6. Release the trigger and engage the gun safety lock.

mWARNING! Turn o the water supply and squeeze the

trigger to depressurize the unit. Failure to do so could result in

personal injury due to discharge of high-pressure water.

Taking a break

If you are taking a break of ve minutes or more between

cleaning tasks:

1. Engage the gun safety lock (Fig. 12).

2. Push the switch to the OFF (0) position.

3. Unplug the power cord from the outlet.

Storage

mCAUTION! Always store your pressure washer in a

location where the temperature will not fall below 32ºF (0ºC).

The pump in this machine is susceptible to permanent damage

if it freezes. FREEZE DAMAGE IS NOT COVERED BY THE

WARRANTY.

• Store the pressure washer indoors in a dry, covered area

where it is not subject to adverse weather conditions.

• It is important to store this product in a frost-free area.

• Always empty water from all hoses, the pump, and the

detergent bottle (if using) before storing.

mCAUTION! The use of a pump protector is

recommended to prevent cold weather damage during storage

over the winter months.

Winterizing + long-term storage

If you must store your pressure washer in a location where

the temperature falls below 32ºF (0ºC), you can minimize the

chance of damage to your machine by utilizing the following

procedure:

• Disconnect all water connections.

• Turn on the machine for a few seconds until the remaining

water in the pump exits. Turn o immediately.

• Do not allow the high-pressure hose to become kinked.

• Store the machine and accessories in a room that does

not reach freezing temperatures.

• Do not store near a furnace or other sources of heat that

may dry out the pump seals.

• Operate the pressure washer with non-corrosive/non-toxic

anti-freeze, a pump saver, or a pump protector before

storing for the winter.

mWARNING! Before reusing, completely ush the unit

out with clear water. Anti-freeze products can damage

paintwork, so you must ensure there is no anti-freeze left in the

system before using it again.

Maintenance

mCAUTION! Before working on the pressure washer,

switch o the unit and disconnect the plug from the power

supply socket.

1. To ensure good performance, check and clean the lter

(Fig. 21). Remove garden hose adapter and the lter. Rinse

the lter with warm water to prevent any foreign matter

from clogging the pump (Fig. 22).

Fig. 21

Water inlet

Garden hose

adapter

Filter

Fig. 22

Filter

2. Clean the nozzle with the needle clean-out tool provided

(Fig. 23). Remove the spray wand from the gun; remove

any dirt from the nozzle hole and rinse.

Fig. 23

Needle clean-out tool

Disposal

Recycling the washer

• Do not dispose of electrical appliances as unsorted

municipal waste. Use separate collection facilities.

• Contact your local government agency for information

regarding the collection systems available.

• If electrical appliances are disposed of in landlls

or dumps, hazardous substances can leak into the

groundwater and get into the food chain, damaging your

health and well-being.

• When replacing old appliances with new ones, the retailer

is legally obligated to take back your old appliance for

disposal free of charge.

Service + Support

If your Sun Joe® SPX3160P-SJG electric pressure washer

requires service or maintenance, please call the Snow Joe® +

Sun Joe® customer service center at 1-866-SNOWJOE

(1-866-766-9563).

Model + Serial Numbers

When contacting the company, reordering parts, or arranging

service from an authorized dealer, you will need to provide the

model and serial numbers, which can be found on the decal

located on the housing of the unit. Copy these numbers into

the space provided below.

Record the following numbers from the housing or handle of your

new product:

S P X 3 1 6 0 P - S J G

Model #:

Serial #:

Troubleshooting

• Disconnect the unit from the electrical power supply before carrying out maintenance on the machine or when checking that

its parts are in proper working order.

• To avoid unnecessary hassles, consult the following table before contacting customer service with any mechanical issues.

Problems Possible Cause Possible Solution

Machine refuses

to start

• Power failure/machine not

plugged into a working receptacle.

• Defective socket.

• Fuse has blown.

• Check to make sure machine is plugged into

a working outlet.

• Check the power cord and reset the GFCI.

Try a dierent outlet.

• Replace fuse. Switch o any other machines

that are using the same circuit.

• Check the hoses and connections are airtight.

• Clean or replace valves/seals.

• Please call the Snow Joe® + Sun Joe® customer

service center at 1-866-SNOWJOE (1-866-766-9563)

for assistance.

• Replace fuse. Switch o other machines using

the same circuit.

• Check that the mains voltage corresponds to

specication on the model tag.

• Leave the washer for 5 minutes to cool down.

• Clean the nozzle.

• Install a fuse with a higher amp rating than the

amp consumption of the machine.

• Allow machine to run by holding the trigger until

regular working pressure resumes.

• Check that the water supply corresponds to the

specications required.

WARNING! Avoid using long, thin hoses

(minimum 1/2 in. diameter).

• Clean the nozzle.

• Clean the water inlet lter.

• Straighten out the hose to remove any kinks/blockages.

• Please call the Snow Joe® + Sun Joe® customer service

center at 1-866-SNOWJOE (1-866-766-9563) for

assistance.

• Wait for pump/hoses or accessories to thaw.

• Connect inlet water.

• Clean the water inlet lter.

• Clean the nozzle.

• Pump sucking air.

• Valves dirty, worn out, or stuck.

• Pump seals worn out.

• Fuse has blown.

• Incorrect mains voltage.

• Thermal sensor activated.

• Nozzle partially blocked.

• Fuse too small.

• Air in inlet hose.

• Inadequate supply of mains water.

• Nozzle partially blocked.

• Water lter blocked.

• Hose kinked.

• Pump/spray gun is leaking.

• Trigger mechanism is broken.

• Pump/hoses or accessories frozen.

• No water supply.

• Water inlet lter blocked.

• Nozzle blocked.

Fluctuating pressure

Machine stops

Fuse blows

Machine pulsating

Machine often starts

and stops by itself

Machine starts, but

no water comes out

Optional Accessories

WARNING! ALWAYS use only authorized Snow Joe® + Sun Joe® replacement parts and accessories. NEVER use replacement

parts or accessories that are not intended for use with this electric pressure washer. Contact Snow Joe® + Sun Joe® if you are

unsure whether it is safe to use a particular replacement part or accessory with your pressure washer. The use of any other

attachment or accessory can be dangerous and could cause injury or mechanical damage.

25-Foot Medium-duty Extension Hose for

SPX Pressure Washer Series

Universal Quick-Connect Coupler

(Garden Hose to Pressure Washer Adapter)

SPX-25H

SPX-UQC

ModelAccessories Item

Sun Joe® House + Deck All-Purpose Pressure

Washer Rated Concentrated Cleaner SPX-HDC1G

Sun Joe® Premium Snow Foam Pressure

Washer Rated Car Wash Soap + Cleaner SPX-FCS1G

Sun Joe® All-Purpose Heavy Duty Pressure

Washer Rated Cleaner + Degreaser SPX-APC1G

Sun Joe’s complete line of premium pressure washer accessories and attachments

make it easy to get your dirty work done, and also help you get the most out of your model!

SHOP ONLINE now at sunjoe.com

NOTE: Accessories are subject to change without any obligation on the part of Snow Joe® + Sun Joe® to provide notice of such

changes. Accessories can be ordered online at sunjoe.com or via phone by contacting the Snow Joe® + Sun Joe® customer

service center at 1-866-SNOWJOE (1-866-766-9563).

R4_01282020

SNOW JOE® + SUN JOE® CUSTOMER PROMISE

OUR WARRANTY:

Snow Joe warrants new, genuine, powered and non-powered Products to be free from defects in material or workmanship when used

for ordinary household use for a period of two years from the date of purchase by the original, end-user purchaser when purchased

from Snow Joe or from one of Snow Joe’s authorized sellers with proof of purchase. Because Snow Joe is unable to control the quality

of its Products sold by unauthorized sellers, unless otherwise prohibited by law, this Warranty does not cover Products purchased from

unauthorized sellers. If your Product does not work or there’s an issue with a specic part that is covered by the terms of this Warranty,

Snow Joe will elect to either (1) send you a free replacement part, (2) replace the Product with a new or comparable product at no

charge, or (3) repair the Product. How cool is that!

This Warranty gives you speciﬁc legal rights, and you may also have other rights which vary from State to State.

PRODUCT REGISTRATION:

Snow Joe strongly encourages you to register your Product. You can register online at snowjoe.com/register, or by printing and

mailing in a registration card available online from our website, or calling our Customer Service Department at 1-866-SNOWJOE

(1-866-766-9563), or by e-mailing us at [email protected]. Failure to register your Product will not diminish your warranty

rights. However, registering your Product will allow Snow Joe to better serve you with any of your customer service needs.

WHO CAN SEEK LIMITED WARRANTY COVERAGE:

This Warranty is extended by Snow Joe to the original purchaser and original owner of the Product.

WHAT IS NOT COVERED?

This Warranty does not apply if the Product has been used commercially or for non-household or rental applications. This Warranty also

does not apply if the Product was purchased from an unauthorized seller. This Warranty also does not cover cosmetic changes that do

not aect performance. Wearing parts like belts, augers, chains and tines are not covered under this Warranty, and can be purchased

at snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563).

ABOVE ALL ELSE, Snow Joe, LLC (“Snow Joe”) is dedicated to you, our customer. We strive to make your experience as pleasant as

possible. Unfortunately, there are times when a Snow Joe®, Sun Joe®, or Aqua Joe® product (“Product”) does not work or breaks under

normal operating conditions. We think it’s important that you know what you can expect from us. That’s why we have a Limited Warranty

(“Warranty”) for our Products.

GUARDE ESTAS INSTRUCCIONES

Una división de Snow Joe®, LLC

MANUAL DEL OPERADOR

LAVADORA A PRESIÓN ELÉCTRICA GO

ANYWHERE 11A

Instrucciones originales.

Modelo SPX3160P-SJG Forma № SJ-SPX3160P-SJG-880S-M-FTY

¡IMPORTANTE!

Instrucciones de seguridad

Todos los operadores deberán leer

estas instrucciones antes del uso

m ¡ADVERTENCIA! Esto indica una situación peligrosa

la cual, de no ser evitada, puede causar lesiones personales

severas o la muerte.

m ¡PRECAUCIÓN! Esto indica una situación peligrosa

la cual, de no ser evitada, puede causar lesiones menores o

moderadas.

m ¡PELIGRO! Esto indica una situación peligrosa la cual,

de no ser evitada, causará lesiones personales severas o la

muerte.

Seguridad general

m ¡ADVERTENCIA! Este artefacto no está destinado

para su uso por niños o por otras personas sin asistencia o

supervisión cuyas habilidades físicas, sensoriales o mentales

les impidan usarlo de forma segura. Los niños deben estar

bajo supervisión para garantizar que no vayan a jugar con la

hidrolavadora eléctrica.

Antes de encender su hidrolavadora eléctrica, inspecciónela

cuidadosamente para comprobar que no tenga defectos.

Si encuentra algún defecto, no la encienda. Contacte a

un concesionario autorizado Snow Joe® + Sun Joe® o

comuníquese con la central de servicio al cliente Snow Joe® +

Sun Joe® llamando al 1-866-SNOWJOE (1-866-766-9563).

m ¡ADVERTENCIA! Al usar esta hidrolavadora eléctrica,

se deberán tomar siempre precauciones básicas de seguridad

para reducir riesgos de incendio, choque eléctrico y lesiones

personales. Estas incluyen:

• Conozca su producto: sepa cómo detener la máquina y

purgar la presión de forma rápida. Familiarícese a fondo

con los controles.

• Mantenga alejados a los transeúntes: todas las personas

y mascotas deberán encontrarse a una distancia segura del

área de trabajo.

• Use el producto adecuado: no utilice esta hidrolavadora

para ningún otro trabajo excepto para el cual ha sido

diseñada.

• Vístase apropiadamente: no utilice prendas holgadas ni

joyería. Pueden llegar a engancharse en las partes móviles.

Al trabajar en exteriores, se recomienda el uso de guantes

de goma y calzado antideslizante.

• m ¡PRECAUCIÓN! Tenga cuidado y evite resbalar o caer.

Utilice calzado protector que proteja sus pies y mejore su

posición de pie en supercies resbaladizas.

• Manténgase alerta: vea lo que está haciendo. Utilice su

sentido común. No opere la hidrolavadora eléctrica si usted

está cansado o bajo la inuencia del alcohol o las drogas.

• No adopte una postura inclinada: mantenga con sus pies

balance y posición adecuados todo el tiempo.

• Evite encendidos accidentales: no transporte la máquina

enchufada con su dedo en el interruptor. Asegúrese de

que el interruptor esté en la posición de apagado antes de

enchufar la unidad.

• No abuse del cable: nunca jale la hidrolavadora por su

cable de alimentación, ni tire bruscamente del cable para

desconectarlo del tomacorriente. Mantenga el cable alejado

del calor, aceites y bordes losos.

• Use gafas protectoras: use también calzado protector,

ropa que se ajuste a su cuerpo, guantes protectores y

protección auditiva y para la cabeza.

• Compruebe la temperatura del agua: esta hidrolavadora

eléctrica no está hecha para bombear agua caliente. NUNCA

la conecte a una fuente de agua caliente ya que reducirá

signicativamente el ciclo de vida útil de la bomba.

• Guárdela en un lugar bajo techo: NUNCA almacene

la hidrolavadora eléctrica en exteriores o donde pueda

congelarse. La bomba podría dañarse seriamente.

• Interruptor de circuito de falla de conexión a tierra

(GFCI): se debe proveer protección en los circuitos o

tomacorrientes a ser usados con esta hidrolavadora. Hay

receptáculos disponibles con protección incorporada GFCI

y pueden ser utilizados para esta medida de seguridad.

• Inspeccione los cables eléctricos: el aislamiento del

cable de alimentación debe estar perfectamente intacto.

Si el cable de alimentación está dañado o hay señales de

desgaste o deterioro, no use la hidrolavadora eléctrica.

Contacte a un concesionario autorizado Snow Joe® + Sun

Joe® o comuníquese con la central de servicio al cliente

Snow Joe® + Sun Joe® llamando al 1-866-SNOWJOE (1-

866-766-9563).

m ¡ADVERTENCIA! No use esta hidrolavadora eléctrica

sin antes leer este manual de instrucciones.

m ¡ADVERTENCIA! Esta hidrolavadora ha sido

diseñada para su uso con agentes de limpieza recomendados

por el fabricante. El uso de otros agentes de limpieza o

químicos puede perjudicar la seguridad del artefacto.

m ¡ADVERTENCIA! No use el artefacto cerca de otras

personas a menos que estas se encuentren usando ropa

protectora.

m ¡ADVERTENCIA! Los chorros de alta presión pueden

ser peligrosos si se manipulan incorrectamente. El chorro no

deberá estar dirigido a personas, mascotas, equipos eléctricos

activos, o al artefacto en sí.

• No dirija el chorro hacia usted o demás personas para

limpiar ropa o calzado.

• Riesgo de explosión: no rocíe líquidos inamables.

• Riesgo de lesiones personales o inyección a personas –

Nunca dirija el chorro de descarga a personas, mascotas o

dispositivos eléctricos.

• Desconecte la hidrolavadora: desconecte la hidrolavadora

eléctrica de la fuente de alimentación antes de llevar a cabo

cualquier tarea de mantenimiento.

• Mantenga alejados a los niños: esta hidrolavadora

eléctrica de alta presión no debe ser usada por niños o

personas no capacitadas.

• Para garantizar un uso seguro del artefacto, use solo partes

de repuesto del fabricante o aprobadas por éste.

m ¡ADVERTENCIA! El agua que ha uido a través de

válvulas contra-reujo se considera no potable.

m ¡ADVERTENCIA! Durante la limpieza, mantenimiento

o reemplazo de partes, desconecte la máquina de su fuente

de alimentación retirando el enchufe del tomacorriente.

m ¡ADVERTENCIA! Las mangueras, juntas y

acoplamientos para presiones altas son importantes para

la seguridad del artefacto. Use solo mangueras, juntas y

acoplamientos recomendados por el fabricante.

• Inspeccione la unidad en busca de partes dañadas: no

use el artefacto si hay daños en el cable de suministro o

en partes importantes; p. ej., dispositivos de seguridad,

mangueras para presión alta o pistola rociadora.

• Esta hidrolavadora eléctrica de alta presión no debe ser

usada a temperaturas menores de 32ºF (0°C).

m ¡ADVERTENCIA! El cable de alimentación debe

estar siempre desenrollado por completo para evitar el

sobrecalentamiento.

• Las conexiones de cables de alimentación deben

permanecer secas y por encima del nivel del suelo.

• Si el cable de alimentación está dañado, no utilice la

hidrolavadora. Contacte a un concesionario autorizado

Snow Joe® + Sun Joe® o comuníquese con la central

de servicio al cliente Snow Joe® + Sun Joe® llamando al

1-866-SNOWJOE (1-866-766-9563).

• Mantenga la máquina en una supercie estable y

plana durante la operación, manipulación, transporte y

almacenamiento. Un volcado repentino de la máquina

puede causar lesiones corporales.

• En caso de accidente o desperfecto, desenchufe la

máquina inmediatamente. (Si hay contacto con el

detergente: enjuague con abundante agua limpia).

Seguridad eléctrica

ATENCIÓN: si hay problemas con la RED ELÉCTRICA,

pueden ocurrir caídas breves de voltaje al encender el equipo.

Estas a su vez pueden afectar otros equipos (como por

ejemplo, una lámpara parpadeando). Si la IMPEDANCIA DE LA

RED (Zmax) es menor que 0.335 ohmios, estas uctuaciones

no son esperadas (si necesita ayuda, comuníquese con la

empresa de suministro eléctrico de su localidad para más

información).

m ¡ADVERTENCIA! Peligro de choque eléctrico: antes

de encender su máquina, inspecciónela cuidadosamente para

comprobar que no tenga defectos. Si encuentra algún defecto,

no la encienda. Contacte a un concesionario autorizado Snow

Joe® + Sun Joe® o comuníquese con la central de servicio al

cliente Snow Joe® + Sun Joe® llamando al 1-866-SNOWJOE

(1-866-766-9563).

Se deberá cumplir lo siguiente al conectar la hidrolavadora

eléctrica de alta presión a la red eléctrica:

• La conexión al suministro eléctrico deberá haber sido

hecha por una persona calicada.

• La alimentación de electricidad a este artefacto deberá

incluir ya sea un dispositivo de corriente residual (RCD)

que interrumpirá el suministro si la corriente de fuga a

tierra excede los 30 mA durante 30 ms, o un interruptor de

circuito a tierra (GFCI).

IMPORTANTE: solo use agua sin impurezas. Si hay un

peligro de arena uyendo en el agua de entrada (p. ej., de su

propio pozo), se deberá instalar un ltro adicional.

Reparación de artefacto de doble

aislamiento

En un artefacto de doble aislamiento, se proporcionan dos

sistemas de aislamiento en lugar de una conexión a tierra. Un

artefacto de doble aislamiento no posee una conexión a tierra,

y no debe agregársele ninguna. La reparación de un artefacto

de doble aislamiento requiere sumo cuidado y conocimiento

del sistema, y solo debe ser realizada por personal técnico

calicado en un centro de servicio autorizado por Snow

Joe® + Sun Joe®. Las partes de repuesto de un artefacto de

doble aislamiento deben ser idénticas a las partes originales.

Un artefacto de doble aislamiento está marcado con las

frases “Double Insulation” (“doblemente aislado”) o “Double

Insulated” (“doble aislamiento”). El símbolo (un cuadrado

dentro de otro) puede también estar marcado en el artefacto.

Dispositivos de seguridad

La válvula del descargador puede reducir la presión si ésta

excede los valores preestablecidos. La pistola rociadora

incluye un dispositivo de trabado. Cuando el trabado está

activado, la pistola rociadora no puede ser operada.

1. Sensor térmico: un sensor térmico protege el motor

contra las sobrecargas. La máquina se reiniciará luego de

unos cuantos minutos, cuando el sensor térmico se haya

enfriado.

2. Interruptor de circuito de falla de conexión a tierra

(GFCI): se deberá proveer un interruptor de circuito de

falla de conexión a tierra (GFCI) en el(los) circuito(s) o

tomacorriente(s) a ser utilizados para la hidrolavadora.

Hay receptáculos disponibles con protección incorporada

GFCI y pueden ser utilizados para esta medida de

seguridad.

3. No se recomienda usar un cable de extensión con esta

hidrolavadora eléctrica. La unidad incluye un cable de

alimentación con GFCI de 35 pies. El uso de un cable de

extensión puede causar una caída de voltaje, produciendo

pérdida de potencia y sobrecalentamiento.

m ¡ADVERTENCIA! Para reducir el riesgo de un choque

eléctrico, este artefacto posee un enchufe polarizado (es

decir, una pata es más ancha que la otra). El enchufe del

aparato encajará completamente, en una sola posición, en un

tomacorriente polarizado.

4. No maltrate el cable. Nunca jale la hidrolavadora eléctrica

por su cable, ni tire de éste para desconectarla del

receptáculo. Mantenga el cable alejado del calor, aceite y

bordes alados.

m¡ADVERTENCIA! Para reducir el riesgo de un choque

eléctrico, mantenga todas las conexiones secas y por encima

del nivel del suelo. No toque el enchufe con las manos

mojadas.

Riesgo de choque eléctrico

• Inspeccione el cable antes del uso.

• No use el cable si está dañado.

• Mantenga todas las conexiones secas y por encima del

suelo.

• No toque el enchufe con las manos mojadas.

• Mantenga el cable alejado del calor y bordes alados.

• No rocíe artefactos ni cableados eléctricos.

Riesgo de explosión

• No rocíe líquidos inamables.

• No use ácidos, alcalinos, solventes, o ningún material

inamable en este producto. Estas sustancias pueden

causar lesiones físicas al operador y daños irreversibles a la

máquina.

Instrucciones adicionales de seguridad

• Alta presión: manténgase alejado de la boquilla.

• Peligro de inyección: el equipo puede causar lesiones

personales severas si el rociado penetra la piel.

• No apunte la pistola a nadie o a ninguna parte de su

cuerpo.

• En caso de penetración en la piel, busque ayuda médica

inmediatamente.

• Antes de reparar, limpiar o retirar cualquier parte, apague la

unidad y reduzca la presión.

• Esta máquina no está diseñada para su conexión a las

redes de suministro de agua potable.

Descripción del producto

Propósito

• Esta hidrolavadora eléctrica ha sido diseñada solo para uso

residencial. Está destinada a trabajos de limpieza ligeros e

intermedios en botes, motocicletas, vehículos recreativos

(RV), vehículos todo-terreno (ATV), remolques, terrazas,

barbacoas, fachadas, muebles de patios y demás.

Áreas de aplicación

• ¡Bajo ninguna circunstancia use la máquina en áreas

potencialmente explosivas!

• La temperatura de operación debe estar entre 32ºF (0ºC) y

104ºF (40ºC).

• La máquina es un ensamblaje con una bomba, empotrada

en una carcasa que absorbe impactos. Para que el

operador cuente con una posición de trabajo óptima,

la máquina viene con una vara rociadora y un mango

antideslizante, cuyas formas y conguraciones cumplen

con los reglamentos aplicables.

• No cubra o modique la vara rociadora o la boquilla de

rociado de ningún modo.

• La hidrolavadora eléctrica de alta presión está diseñada

para ser usada con agua fría o tibia. El agua a temperaturas

más elevadas puede dañar la bomba.

• No use agua que esté sucia, arenosa, o contenga

productos químicos, ya que dichas impurezas pueden

afectar negativamente la operación y reducir el ciclo de

vida útil de la hidrolavadora.

Símbolos de seguridad

La siguiente tabla muestra y describe los símbolos de seguridad que pueden aparecer en esta hidrolavadora. Lea, comprenda y

siga todas las instrucciones relacionadas a esta hidrolavadora antes de intentar ensamblarla y operarla.

Para reducir el riesgo de lesiones,

el usuario debe mantener a los

transeúntes alejados al menos a

49 pies (15 m) de distancia.

Mantenga siempre el cable de

alimentación alejado de fuentes

de calor, aceites o bordes alados.

Retire inmediatamente el enchufe

del tomacorriente si el cable se daña

o se enreda.

LEA EL(LOS) MANUAL(ES) DEL

OPERADOR: lea, comprenda y

siga todas las instrucciones en

el(los) manual(es) antes de intentar

ensamblar y operar esta unidad.

ALERTA DE SEGURIDAD: indica

una precaución, advertencia o

peligro.

USE PROTECCIÓN OCULAR Y

AUDITIVA: para evitar lesiones,

use protección auditiva y gafas

protectoras.

Doble aislamiento: al prestar servicio, use solo partes de repuesto idénticas.

¡ADVERTENCIA! No exponga la

unidad a la lluvia o a condiciones

húmedas. Manténgala seca.

La máquina no es adecuada para su

conexión a la red de suministro de

agua potable.

¡ADVERTENCIA! Peligro de choque

eléctrico.

¡ADVERTENCIA! Apague la

máquina y desconéctela de la

fuente de alimentación antes de

inspeccionarla, limpiarla, cambiarle

accesorios o llevar a cabo cualquier

otra tarea de mantenimiento en ésta.

Símbolo SímboloDescripción Descripción

Utilice calzado antideslizante

que proteja sus pies y mejore su

posición de pie en supercies

resbaladizas.

Use guantes de seguridad

durante el uso para proteger

sus manos.

Guarde la hidrolavadora eléctrica

en interiores. Nunca la almacene

en exteriores. Si la bomba se

congela, puede dañarse de forma

permanente.

La page charge ...

sunjoe SPX3160P-SJG Le manuel du propriétaire

Marque: sunjoe

Modèle: SPX3160P-SJG

Catégorie: Nettoyeurs haute pression

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: sunjoe SPX3160P-SJG Owner's manual
español: sunjoe SPX3160P-SJG El manual del propietario