Simplicity SEARS CRAFTSMAN SNOWTHROWER, 13.5 TP, 27 INCH Manuel utilisateur

SEARS CANADA INC., TORONTO, ONTARIO M5B 2B8

Owner’s

Manual

Model

C950-52850-0

13.5 T.P.

27 inch

CAUTION:

You must read and

understand this owner’s

manual before operating

unit.

Serial No. ______________

DUAL STAGE

SNOWTHROWER

1736599, Rev. B 11/2008

Not for

Reproduction

RULES FOR SAFE OPERATION

2

General Information

This instruction book is written for a person with some mechanical ability.

Like most service books, not all the steps are described. Steps on how to

loosen or tighten fasteners are steps anyone can follow with some

mechanical ability. Read and follow these instructions before you use the

unit.

Know your product: If you understand the unit and how the unit

operates, you will get the best performance. As you read this manual,

compare the illustrations to the unit. Learn the location and the function of

the controls. To help prevent an accident, follow the operating instructions

and the safety rules. Keep this manual for future reference.

IMPORTANT: Many units are not assembled and are sold in cartons. It is

the responsibility of the owner to make sure the assembly instructions in

this manual are exactly followed. Other units are purchased in an

assembled condition. On assembled units, it is the responsibility of the

owner to make sure the unit is correctly assembled. The owner must

carefully check the unit according to the instructions in this manual before

it is first used.

This manual contains safety information to make you

aware of the hazards and risks associated with snow

throwers, and how to avoid them. The snow thrower is designed and

intended for removal of snow, and should not be used for any other

purpose. It is important that you read and understand these

instructions, and anyone operating the equipment read and

understand these instructions.

The engine exhaust from this product contains chemicals known to the

State of California to cause cancer, birth defects, or other reproductive

harm.

WARNING

A signal word (DANGER, WARNING, or CAUTION) is used with the alert

symbol to indicate the likelihood and the potential severity of injury. In

addition, a hazard symbol may be used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in

death or serious injury.

WARNING indicates a hazard which, if not avoided, could result

in death or serious injury.

CAUTION indicates a hazard which, if not avoided, might result

in minor or moderate injury.

CAUTION, when used without the alert symbol, indicates a

situation that could result in damage to the equipment.

Hazard Symbols and the meanings

These symbols are used on your equipment and defined in your operating

manual. Review and understand the meanings. The use of one of these

symbols combined with a signal word will alert you to potential hazards

and how to avoid them.

Explosion

Toxic fumes

Shock

Hot Surface

Fire

Operator’s Manual ï Read and understand

before performing any activity or running

equipment.

Safety Alert ï Identifies safety information about

hazards that can result in personal injury.

Rotating auger

Rotating impeller

Rotating gears

Thrown objects

Keep a safe distance

from the equipment.

Shut off engine and

remove spark plug

connector before

performing maintenance

or repair work.

Never reach into

rotating parts.

Recommended ear

protection for

extended use.

Not for

Reproduction

RULES FOR SAFE OPERATION

3

Operating Symbols and their meanings

These symbols are used on your equipment and defined in your operating

manual. It is important that you review and understand the meanings.

Failure to understand the symbols might result in harm to you.

Stop

Fuel

Choke off

Oil

Choke on

Slow

Fast

On Off

Ignition Key

Ignition Off

Ignition On

Primer bulb

Throttle

Drive Clutch

Auger Clutch

Engage

RIGHT

Auger Collector

Traction

Discharge Chute

LEFT UP DOWN

Forward

Neutral

Reverse

Push to engage

electric start

Electric

Start

Engine

Start

Engine Run

Engine Off

Chute Deflector

Engage

Disengage

Heated Grips

Avoid death or serious injury from rotating auger.

Keep hands, feet and clothing away.

Unclogging discharge chute is a hazardous activity.

sStop engine and disconnect spark plug wire when performing maintenance

on equipment.

sNever leave the equipment unattended while engine is running. Always

disengage the auger and traction controls, stop engine, and remove keys.

sKeep children, pets, and others out of the area during operation. Children

are often attracted to the equipment. Be mindful of all persons present.

sKeep all loose clothing far away from front of snow thrower and auger.

Scarves, mittens, dangling drawstrings, loose clothes and pants can

quickly become caught in the rotating device and dismemberment will

occur. Tie up long hair and remove jewelry.

sThe snow thrower is intended to remove snow only. Do not use for

purposes other than what is intended.

sDo not clear snow across the face of slopes. Exercise extreme caution when

changing direction on slopes. Do not attempt to clear steep slopes.

sDo not use the snow thrower on surfaces above ground level such as roofs

of residences, garages, porches or other such structures or buildings.

DANGER

Discharge chute contains rotating impeller to throw snow.

Never clear or unclog discharge chute with your hands, or

while engine is running.

Fingers can quickly become caught and traumatic

amputation or severe laceration can result.

sUnclogging the discharge chute is a hazardous activity. Clogged or

blocked augers store energy and can rotate unexpectedly.

sNever place hands in or near discharge chute.

sWith engine OFF, wait for all moving parts to cease movement, then with a

stick, clear the chute. Even with engine off, parts may rotate and

dismemberment can occur.

sClogged snow can hide other obstructions in the chute and cause damage

to the equipment, impeller or auger. Take precautions when restating the

equipment after snow removal.

DANGER

Not for

Reproduction

RULES FOR SAFE OPERATION

4

Objects can be picked up by auger and thrown from chute.

Never throw snow toward people or cars, and never allow

anyone in front of the snow thrower.

•Be aware of your environment while operating equipment. Running over

items such as, gravel, doormats, newspapers, toys, and rocks hidden

under snow, can all be thrown from chute or jam in the auger.

•Always be aware of the direction the snow is being thrown. Nearby

pedestrians, pets or property may be harmed by objects being thrown.

•Familiarize yourself with the area you plan to work. Mark off boundaries of

walkways and driveways to prevent property damage from thrown objects.

•Take caution when snow throwing in unfamiliar areas. Stay alert for hidden

hazards and traffic.

•After striking a foreign object, turn engine OFF, wait for moving parts to

cease movement, and check immediately for damage. If damaged, repair

before starting and operating snow thrower.

•With engine OFF, wait for moving parts to stop and always use a stick to

clear discharge chute.

•If unit vibrates abnormally, turn engine OFF. Vibration is generally a

warning of trouble. See an authorized dealer if necessary for repairs.

DANGER

Rotating gears can contact or entangle hands, feet, hair,

clothing, or accessories.

Traumatic amputation or severe laceration can result.

•Always operate equipment with all guards in place.

•Keep hands and feet away from rotating gears.

•Tie up long hair and remove jewelry.

•Do not wear loose-fitting clothing, dangling drawstrings or items that could

become caught.

WARNING

Engines give off carbon monoxide, an odorless, colorless,

poison gas.

Breathing carbon monoxide can cause nausea, fainting or

death.

•Start and run engine outdoors.

•Do not start or run engine in enclosed area, even if doors or

windows are open.

WARNING

•Allow muffler, engine cylinder and fins to cool before touching.

•Remove accumulated combustibles from muffler area and cylinder

area.

•Install and maintain in working order a spark arrester before using

equipment on forest-covered, grass-covered, brush-covered

unimproved land. The state of California requires this (Section 4442 of

the California Public Resources Code). Other states may have similar

laws. Federal laws apply on federal land.

WARNING

Running engines produce heat. Engine parts, especially muffler,

become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch

fire.

Gasoline and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

WHEN ADDING FUEL

•Turn engine OFF and let engine cool at least 2 minutes before removing

gas cap.

•Fill fuel tank outdoors or in well-ventilated area.

•Do not overfill fuel tank.

•Keep gasoline away from sparks, open flames, pilot lights, heat, and other

ignition sources.

•Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary.

WHEN STARTING ENGINE

•Make sure spark plug, muffler, fuel cap and air cleaner are in place.

•Do not crank engine with spark plug removed.

•If fuel spills, wait until it evaporates before starting engine.

•If engine floods, set choke to OPEN/RUN position, place throttle in FAST

and crank until engine starts.

WHEN OPERATING EQUIPMENT

•Do not choke carburetor to stop engine.

WHEN TRANSPORTING EQUIPMENT

•Transport with fuel tank EMPTY.

WHEN STORING GASOLINE OR EQUIPMENT WITH FUEL IN TANK

•Store away from furnaces, stoves, water heaters or other appliances that

have pilot light or other ignition source because they can ignite gasoline

vapors.

WARNING

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

•If there is natural or LP gas leakage in area, do not start engine.

•Do not use pressurized starting fluids because vapors are flammable.

WARNING

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

BEFORE PERFORMING ADJUSTMENTS OR REPAIRS

•Disconnect spark plug wire and keep it away from spark plug.

WHEN TESTING FOR SPARK

•Use approved spark plug tester.

•Do not check for spark with spark plug removed.

WARNING

Not for

Reproduction

IMPORTANT: Safety standards require operator presence control to

minimize the risk of injury. Your snowthrower is equipped with such

controls. Do not attempt to defeat the function of the operator presence

control under any circumstances.

Training

1. Read, understand, and follow all instructions on the machine and in

the manuals before operating this unit. Be thoroughly familiar with

the controls and the proper use of the equipment. Know how to stop

the unit and disengage the controls quickly.

2. Never allow children to operate the equipment. Never allow adults to

operate the equipment without proper instruction.

3. Keep the area of operation clear of all persons, particularly small

children, and pets.

4. Exercise caution to avoid slipping or falling especially when operating

in reverse.

Preparation

1. Thoroughly inspect the area where the equipment is to be used and

remove all doormats, sleds, boards, wires, and other foreign objects.

2. Disengage all clutches and shift into neutral before starting the

engine (motor).

3. Do not operate the equipment without wearing adequate winter outer

garments. Wear footwear that will improve footing on slippery

surfaces. Avoid loose fitting clothing that can get caught in moving

parts.

4. Handle fuel with care; it is highly flammable.

a. Use an approved fuel container.

b. Never add fuel to a running engine or hot engine.

c. Fill fuel tank outdoors with extreme care. Never fill fuel tank

indoors. Replace fuel cap securely and wipe up spilled fuel.

d. Never fill containers inside a vehicle or on a truck or trailer bed

with a plastic liner. Always place containers on the ground, away

from your vehicle, before filling.

ro kcurt eht morf tnempiuqe derewop- sag evomer ,lacitcarp nehW.e

trailer and refuel it on the ground. If this is not possible, then refuel

such on a trailer with a portable container, rather than from a

gasoline dispenser nozzle.

f. Keep nozzle in contact with the rim of the fuel tank or container

opening at all times, until refueling is complete. Do not use a

nozzle lock-open device.

g. Replace gasoline cap securely and wipe up spilled fuel.

h. If fuel is spilled on clothing, change clothing immediately.

5. Use extension cords and receptacles as specified by the

manufacturer for all units with electric drive motors or electric

starting motors.

6. Adjust the collector housing height to clear gravel or crushed rock

surfaces.

7. Never attempt to make any adjustments while the engine (motor) is

running (except when specifically recommended by manufacturer).

8. Let engine (motor) and snowthrower adjust to outdoor temperatures

before starting to clear snow.

9. Always wear safety glasses or eye shields during operation or while

performing an adjustment or repair to protect eyes from foreign

objects that may be thrown from the machine.

Operation

1. Do not put hands or feet near or under rotating parts. Keep clear of

the discharge opening at all times.

2. Exercise extreme caution when operating on or crossing gravel

drives, walks or roads. Stay alert for hidden hazards or traffic.

3. After striking a foreign object, stop the engine (motor), remove the

wire from the spark plug, disconnect the cord on electric motors,

thoroughly inspect snowthrower for any damage, and repair the

damage before restarting and operating the snowthrower.

4. If the unit should start to vibrate abnormally, stop the engine (motor)

and check immediately for the cause. Vibration is generally a warning

of trouble.

5. Stop the engine (motor) whenever you leave the operating position,

before unclogging the collector/impeller housing or discharge chute

and when making any repairs, adjustments, or inspections.

6. When cleaning, repairing, or inspecting, make certain the collector/

impeller and all moving parts have stopped. Disconnect the spark

plug wire and keep the wire away from the spark plug to prevent

accidental starting.

7. Do not run the engine indoors, except when starting the engine and

for transporting the snowthrower in or out of the building. Open the

outside doors; exhaust fumes are dangerous (containing CARBON

MONOXIDE, an ODORLESS and DEADLY GAS).

8. Exercise extreme caution when operating on slopes. Do not attempt

to clear steep slopes.

9. Never operate the snowthrower without proper guards, plates, or

other safety protective devices in place and working.

10. Never direct the discharge toward people or areas where property

damage can occur. Keep children and others away.

11. Do not overload the machine capacity by attempting to clear snow at

too fast a rate.

12. Never operate the machine at high transport speeds on slippery

surfaces. Look behind and use care when operating in reverse.

13. Disengage power to the collector/impeller when snowthrower is

transported or not in use.

14. Use only attachments and accessories approved by the manufacturer

of the snowthrower (such as cabs, tire chains, etc.).

15. Never operate the snowthrower without good visibility or light.

Always be sure of your footing and keep a firm hold on the handles.

Walk, never run.

16. Never touch a hot engine or muffler.

RULES FOR SAFE OPERATION

5

WARNING: This machine is capable of amputating hands and feet and throwing objects. Read these safety rules and follow them closely.

Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property

or equipment. The triangle in text signifies important cautions or warnings which must be followed.

Safe Operation Practices for Snowthrowers

As Recommended By: American National Standards Institute (ANSI)

Not for

Reproduction

17. Never operate the snowthrower near glass enclosures, automobiles,

window wells, drop-offs, and the like without proper adjustment of

the snow discharge angle.

18. Never direct discharge at bystanders or allow anyone in front of the

unit.

19. Never leave a running unit unattended. Always disengage the auger

and traction controls, stop engine, and remove keys.

20. Do not operate the unit while under the influence of alcohol or drugs.

21. Keep in mind the operator is responsible for accidents occurring to

other people or property.

22. Data indicates that operators, age 60 years and above, are involved

in a large percentage of power equipment-related injuries. These

operators should evaluate their ability to operate the unit safely

enough to protect themselves and others from injury.

23. DO NOT wear long scarves or loose clothing that could become

entangled in moving parts.

24. Snow can hide obstacles. Make sure to remove all obstacles from the

area to be cleared.

Children

Tragic accidents can occur if the operator is not alert to the presence of

children. Children are often attracted to the unit and the operating activity.

Never assume that children will remain where you last saw them.

1. Keep children out of the area and under the watchful care of another

responsible adult.

2. Be alert and turn off if children enter the area.

3. Never allow children to operate the unit.

4. Use extra care when approaching blind corners, shrubs, trees, or

other objects that may obscure vision.

Clearing A Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the

most common cause of injury associated with snowthrowers. Never use

your hand to clean out the discharge chute.

To clear the chute:

1. SHUT OFF THE ENGINE.

2. Wait 10 seconds to be sure the impeller blades have stopped

rotating.

3. Always use a clean-out tool, not your hands.

Service, Maintenance And Storage

1. Check shear bolts and other bolts at frequent intervals for proper

tightness to be sure the equipment is in safe working condition.

2. Never store the machine with fuel in the tank inside a building where

ignition sources are present such as hot water and space heaters, or

clothes dryers. Allow the engine to cool before storing in any

enclosure.

3. Always refer to operator’s manual for important details if the

snowthrower is to be stored for an extended period.

4. Maintain or replace safety and instruction labels as necessary.

5. Run the machine a few minutes after throwing snow to prevent

freeze-up of the collector/impeller.

6. If fuel is spilled, do not attempt to start the engine but move the

machine away from the area of spillage and avoid creating any source

of ignition until fuel vapors have dissipated.

7. Always observe safe refueling and fuel handling practices when

refueling the unit after transportation or storage.

8. Always follow the engine manual instructions for storage

preparations before storing the unit for both short and long term

periods.

9. Always follow the engine manual instructions for proper start-up

procedures when returning the unit to service.

10. Maintain or replace safety and instruction labels as necessary.

11. Keep nuts and bolts tight and keep equipment in good condition.

12. Never tamper with safety devices. Check their proper operation

regularly and make necessary repairs if they are not functioning

properly.

13. Components are subject to wear, damage, and deterioration.

Frequently check components and replace with manufacturer’s

recommended parts, when necessary.

14. Check control operation frequently. Adjust and service as required.

15. Use only factory authorized replacement parts when making repairs.

16. Always comply with factory specifications on all settings and

adjustments.

17. Only authorized service locations should be utilized for major service

and repair requirements.

18. Never attempt to make major repairs on this unit unless you have

been properly trained. Improper service procedures can result in

hazardous operation, equipment damage and voiding of

manufacturer’s warranty.

19. Check shear bolts (pins) and other bolts at frequent intervals for

proper tightness to be sure the equipment is in safe working

condition.

Emissions

1. Engine exhaust from this product contains chemicals known, in

certain quantities, to cause cancer, birth defects, or reproductive

harm.

2. If available, look for the relevant Emissions Durability Period and Air

Index information on the engine emissions label.

Ignition System

1. This spark ignition system complies with Canadian standard

ICES-002.

RULES FOR SAFE OPERATION

6

Not for

Reproduction

OWNER’S INFORMATION

7

MAINTENANCE AGREEMENT

The Craftsman Warranty, plus a Maintenance

Agreement, provide maximum value for Sears

products. Contact your nearest Sears store for de-

tails.

Gross Torque 13.5 T.P.

Gasoline Capacity 4 quarts (3.8 litre)

Oil Capacity (5W30) 28 oz (0.84 litres)

Spark Plug: (Gap .030 in.) Champion RC12YC

CUSTOMER RESPONSIBILITIES

Read and observe the safety rules.

Follow a regular schedule in maintaining, caring for and

using your snowthrower.

Follow the instructions under CUSTOMER RESPONSIBIL-

ITIES and STORAGE sections of this owner’s manual.

* See side of the tire for maximum inflation. Do not exceed the

maximum pressure on the tire wall.

*Tire Pressure

DATE PURCHASED:

MODEL NO:

SERIAL NO:

STORE WHERE PURCHASED:

ADDRESS:

CITY: PROVINCE:

TELEPHONE:

Record this information about your unit so that you will

be able to provide it in case of loss or theft. Armature Air Gap 0.010--0.014 in.

(0.25--0.36 mm)

Bore 3.120 in. (79 mm)

Stroke 2.438 in. (62 mm)

Displacement 305 cc

WHEELED SNOWTHROWER

LIMITED TWO (2) YEAR WARRANTY ON CRAFTSMAN SNOWTHROWER

For two (2) years from date of purchase, Sears Canada Inc. will repair or replace free of charge, at Sears option, parts

which are defective as a result of material or workmanship.

COMMERCIAL OR RENTAL USE:

Warranty on snowthrower will be 90 days from date of purchase if used for commercial or rental purposes.

THIS WARRANTY DOES NOT COVER:

1. Pre--delivery set--up.

2. Expendable items which become worn during normal use, such as belts, spark plugs, filter, shear pins as well as dam-

ages to the engine resulting from operating the snowthrower with insufficient oil.

3. Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps or glass.

4. In home service.

Warranty service is available by returning the Craftsman snowthrower to the nearest Sears Service Centre/Department

in Canada. This warranty applies only while this product is in use in Canada.

This warranty is in addition to any statutory warranty and does NOT exclude or limit legal rights you may have but shall

run concurrently with applicable provincial legislation. Furthermore, some provinces do not allow limitations on how long

an implied warranty will last so the above limitations may not apply to you.

SEARS CANADA INC., TORONTO, ONTARIO M5B 2B8

Not for

Reproduction

TABLE OF CONTENTS

8

HAZARD SYMBOLS AND THE MEANINGS 2..........

OPERATING SYMBOLS AND THEIR MEANINGS 3....

7NOITAMROFNIS’RENW.........................O

9YLBMESSA ......................................

TOOLS REQUIRED FOR ASSEMBLY 9.............

CONTENTS OF SHIPPING CARTON 9.............

PARTS BAG CONTENTS . . . . . . . . . . . . . . . . . . . . . . 9

UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

ASSEMBLE UPPER/LOWER HANDLES . . . . . . . . . . 11

11SELBACEHTKCEHC .......................... .

HOW TO SET THE LENGTH OF THE CABLES . . . .

ASSEMBLE THE SPEED CONTROL ROD AND

SPEED SELECT LEVER . . . . . . . . . . . . . . . . . . . . 12

SNOW CHUTE ASSEMBLY . . . . . . . . . . . . . . . . . . . . 13

HOW TO ASSEMBLE THE DRIFT CUTTER . . . . . . . 14

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATING CONTROLS . . . . . . . . . . . . . . . . . . . . . 15

SNOWTHROWER OPERATION . . . . . . . . . . . . . . . .

81 ENIGNEG

NIT

R

A

T

S

EROFE...................B

CHECK THE OIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

FILL GAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

TOSTOP ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

TO START ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . 19

HOW TO CLEAR A CLOGGED

DISCHARGE CHUTE . . . . . . . . . . . . . . . . . . . . . . . . . . 21

HOW TO USE THE CLEAN-OUT TOOL . . . . . . . . . .

22SPITGNITAREPO .............................

SERVICE RECOMMENDATIONS 23..................

CUSTOMER RESPONSIBILITIES 24..................

SNOWTHROWER . . . . . . . . . . . . . . . . . . . . . . . . . . .

42DERIUQERSA ................................

42EGAROTSTANOITACIRBU..

.................L

LUBRICATION -- EVERY 10 HOURS 24.............

LUBRICATION -- EVERY 25 HOURS 25.............

62ENIGNE ......................................

72RIAPER/TNEMTSU

JD

A..........................

AUGER HOUSING HEIGHT ADJUSTMENT 27.......

72RABREPARCSTSUJDAOT ....................

72THGIEHDIKSTSUJDAO.....................T

HOW TO REMOVE THE SNOW HOOD 28...........

92TNEMTSUJDATLEB ...........................

HOW TO REPLACE THE BELTS 30................

33TNEMTSUJDAEDIUGTLE....................B

HOW TO CHECK AND ADJUST THE CABLES 33...

AUGER DRIVE CABLE ADJUSTMENT 33...........

TRACTION DRIVE CABLE ADJUSTMENT 34........

HOW TO ADJUST OR REPLACE

53LEEH

WN

OITCIRFEHT ......................

AUGER SHEAR BOLTREPLACEMENT 38..........

15

18

17

21

FROZEN STARTER . . . . . . . . . . . . . . . . . . . . . . . . . . 21

24

93EGAROTS ......................................

04TRAHCGNITOOHSELBUOR....................T

34STRAPRIAPER ................................. .

42STRAPRIAPERREDR..........................O

11

Not for

Reproduction

9

ASSEMBLY

TOOLS REQUIRED FOR ASSEMBLY

1 -- Knife

2 -- 1/2” wrenches (or adjustable wrenches)

2 -- 7/16” wrenches (or adjustable wrenches)

1 -- 3/8” wrenches (or adjustable wrenches)

1 -- Screw driver (to spread cotter pin)

HOW TO MEASURE SCREW SIZE

LENGTH

DIAMETER

CONTENTS OF SHIPPING CARTON

1-- Snowthrower

1-- Container of Fuel Stabilizer (Located in Parts Bag)

1-- Parts Bag

WARNING: Always wear safety glasses or eye

shields while assembling snowthrower.

PARTS BAG CONTENTS*

1 -- Washer .31 x .58 x .08

1 -- Nut, Hex .31-24

1 -- Shear Bolt Kit .31-18 x 2.0

2 -- Tool, Hex

*Non Assembly parts and power cord can be found in the Parts Bag shipped

with the snow thrower. The parts can be stored in the tool box located on top

of the belt cover.

Not for

Reproduction

ASSEMBLY

10

Figure 1 shows the snowthrower in the shipping position.

Figure 2 shows the snowthrower completely assembled.

Reference to right and left hand side of the snowthrower is

from the operator’s position at the handle.

UNPACKING

1. The snowthrower is shown in the shipping position

(see Figure 1).

2. Cut down all four corners of the carton and lay the

side panels flat.

3. Locate all parts that are packed separately and

remove from the carton.

4. Remove and discard the packing material from

around the snowthrower.

NOTE: Set the fuel stabilizer aside until adding

gasoline to the fuel tank. We recommend that fuel

stabilizer is added to the fuel each time that gasoline

is added to the fuel tank.

5. Remove the packing material from the handle assembly.

6. Cut ties securing the clutch control cables to the lower

handle.

NOTE: If the cables have become disconnected from the

clutch levers, reinstall the cables as shown in Figure 3.

Figure 1

Figure 2

Auger Drive

Clutch Lever Traction Drive

Clutch Lever

Snow Chute

Deflector

Height Adjust

Skid

Auger

Housing

Remote Deflector

Control

Speed Select

Lever

Toolbox

Figure 3

Drive Lever

Cable

”Z” Fitting

Not for

Reproduction

ASSEMBLY

11

ASSEMBLE UPPER/LOWER HANDLES

1. Raise the upper handle (A, Figure 4) to the operating

position.

NOTE: Make sure the cables are not caught between

the upper and lower handle.

2. Assemble the upper and lower handle (A, B) as

shown in Figure 4.

3. Make sure all fasteners (C) are secure.

CHECK THE CABLES

1. If control cables have become unattached from

motor mount frame, reconnect traction drive cable

(D, Figure 4) and auger drive cable (E) as shown.

2. For cable adjustments, see “How To Check And Adjust

The Cables” in the ADJUSTMENT/REPAIR section.

HOW TO SET

THE LENGTH OF THE CABLES

The cables were adjusted at the factory and no adjustments

should be necessary. However, after the handles are put in

the operating position, the cables can be too tight or too

loose. If an adjustment is necessary, see “How To Check And

Adjust The Cables” in the ADJUSTMENT/REPAIR section.

Figure 4

C

D

A

B

E

4. Roll the snowthrower off the carton by pulling on the

lower handle.

CAUTION: DO NOT back over cables.

Not for

Reproduction

ASSEMBLY

12

Figure 5

ASSEMBLE THE SPEED CONTROL ROD

AND SPEED SELECT LEVER

1. Assemble the speed select lever (A, Figure 5) to the speed

control rod using screw and nut.

2. Attach the ball joint (B, Figure 6), located on the bottom end

of the speed control rod (A), to the shift yoke assembly (F).

3. The length of the ball joint dn a speed control rod have been

pre-adjusted at the factory.

a. If an adjustment is required, loosen the nut (C). Remove

the washer (D) and nut (E) to disconnect the ball joint

from the shift yoke assembly (F).

b. To lengthen or shorten the speed control rod, turn the

ball joint to obtain the correct length.

4. Make sure the speed select lever (A, Figure 5) functions cor-

rectly. Move the speed select lever through all speeds.

5. Attach the knob (B) for the remote deflector control.

C

AA

D

B

E

F

Figure 6

A

B

(see Figure 6)

Not for

Reproduction

ASSEMBLY

13

Figure 8

Assemble Remote Deflector Cable

2. Attach rod (B) to deflector post.

1. Slide compression spring (A, Figure 8) over rod and

insert into hole on chute deflector bracket.

3. Attach remote deflector cable (C) to deflector post.

Secure with push nut (D).

NOTE: Before completing Step 4, make sure that the

chute deflector is in the full open position.

4. Route remote deflector cable (C) through slot in chute

deflector bracket. Secure with nuts (E) and washers

on either side of bracket.

5. Check remote deflector chute for proper operation.

Make adjustments as necessary.

SNOW CHUTE ASSEMBLY

NOTE: The chute ring assembly (A) comes installed

on the unit from the factory (see Figure 7).

NOTE: Make sure the notch in the chute ring aligns

with the arrow on the outer ring.

1. Install chute deflector (B, Figure 7) using four

four screws (C) and nuts (D) in holes as shown.

The chute deflector must point forward for proper

installation.

2. Tighten screws snugly but be careful not to

over-tighten.

Assemble Chute Deflector

Figure 7

A

B

C

D

B

A

D

C

E

F

Not for

Reproduction

ASSEMBLY

14

HOW TO ASSEMBLE THE DRIFT CUTTER

Drift cutters are used to cut a path through snow deeper than

the auger housing.

1. Loosen the wing nuts that secure the drift cutters to

the auger housing (see Figure 9).

2. Raise the drift cutters to the desired height.

3. Tighten the wing nuts.

Drift Cutter

Wing Nut

Figure 9

CHECK THE TIRES

The tires were over inflated for shipment. Check the tire

pressure in the tires. See the sidewall of the tire for the

proper inflation.

IMPORTANT! BEFORE YOU START

OPERATING

Check the fasteners. Make sure all fasteners are

tight.

On electric start models, the unit was shipped with

the starter cord plugged into the engine. Before

operating, unplug the starter cord from the engine.

NOTE: This snowthrower was shipped WITH OIL in the engine. See “Before Starting Engine” in-

structions in the OPERATION section of this manual before starting engine.

Not for

Reproduction

OPERATION

15

Get to know your snowthrower and its controls. Be sure you (or any other operator) have read and understood the RULES

FOR SAFE OPERATION (see page 2).

Figure 10

Auger Drive Clutch

Lever

Traction Drive Clutch

Lever

Speed Select

Lever

Snow Chute

Deflector

Clean-out Tool

Height Adjust Skid

Remote Chute Deflector

Lever

Drift Cutter

Heated Hand

Grip Switch

Auger Housing

Toolbox

Electric Chute

Switch

Primer Button

Gas Fill & Gauge

Starter

Handle

Throttle Control

Lever

Ignition

Key

Choke Lever

Electric

Start Button

Not for

Reproduction

OPERATION

16

The snowthrower operating controls and their functions

are as follows:

Speed Select Lever-- Allows the operator to use one of six

(6) forward and two (2) reverse speeds. To shift, move speed

select lever to desired position.

NOTE: Do not move speed select lever while Traction

Drive Clutch is engaged. This may result in severe

damage to drive system.

Auger Drive Clutch Lever-- Used to engage and disengage

the auger and impeller. To engage push down, to disengage

release.

Traction Drive Clutch Lever-- Used to propel snowthrower

forward or reverse. Push down to engage, release to

disengage.

Heated Hand Grip Switch -- Turns on the heated hand

grips.

Remote Chute Deflector Lever-- Pull remote lever back to

discharge snow high and far. Push remote lever forward to

discharge snow down.

Electric Chute Switch -- Changes the direction of snow

throwing through the discharge chute.

Height Adjust Skid -- Used to adjust ground clearance of

auger housing (see “To Adjust Skid Height” in the

ADJUSTMENT/REPAIR section of this manual).

Toolbox -- Spare shear pins, shear bolt wrenches and

spacers are located in toolbox.

Drift Cutters -- Cuts a path through snow higher than the

auger housing.

Clean-Out Tool -- Use the clean-out tool to remove snow and

debirs from the discharge chute and the auger housing.

ENGINE AND SNOWTHROWER OPERATING CONTROLS

The engine operating controls and their functions are as

follows:

Throttle Control Lever -- This snowthrower is equipped with

an engine mounted throttle control lever used to start a cold

engine.

Choke Lever-- Set choke lever to ON CHOKE position to

start a cold engine.

Electric Start Button-- Used to start the engine using the

electric starter.

Primer Button-- Used to inject fuel directly into car-

buretor manifold to insure fast starts in cool weather.

Ignition Key-- Must be inserted into ignition key slot to

start engine. Pull out to stop. Do not turn ignition key.

Starter Handle-- Starts the engine manually.

Not for

Reproduction

OPERATION

17

The operation of any snowthrower can result in foreign objects being thrown into the eyes,which can

result in severe eye damage. Always wear safety glasses or eye shields before beginning snowthrower

Operation. We recommend standard safety glasses or Wide Vision Safety Mask for over spectacles.

SNOWTHROWER OPERATION

The most effective use of the snowthrower will be established

by experience, taking into consideration the terrain, wind

conditions and building location which will determine the

direction of the discharge chute.

NOTE: Do not blow snow towards a building as hidden

objects could be blown with sufficient force to cause

damage.

1. Start the engine as described in section “To Start En-

gine”.

2. Adjust snow chute deflector. Push the remote chute le-

ver forward to discharge snow down, pull remote chute

deflector back to discharge snow high and far (see

Figure 11).

3. Move the electric chute switch to set the direction (left to

right) of the discharge chute.

4. Select proper speed for snow conditions as outlined be-

low and set speed select lever to desired position.

NOTE: Always release traction drive clutch lever

before moving speed select lever.

Ground speed is determined by snow conditions. Select

the speed you desire by moving the speed selector into

the appropriate colored area on the control panel.

1--2 Wet, Heavy, Slushy, Extra Deep

3Moderate

4--5 Very Light

6Transport Only

NOTE: When clearing wet, heavy snow, it is

recommended that the ground speed of the unit be

reduced, maintain full throttle and do not attempt to

clear the full width of the unit.

For additional operating instructions see “Operating

Tips” in this section of the manual.

6. Engage auger drive clutch lever (right hand--Figure 11).

IMPORTANT: Be sure front of unit is clear of

bystanders or obstacles before operating.

7. Engage traction drive clutch lever (left hand--Figure 11).

As the snowthrower starts to move, maintain a firm hold

on the handles and guide the snowthrower along the cut-

ting path. Do not attempt to push the snowthrower.

8. To stop forward motion, release traction drive clutch lever

(left hand -- Figure 11).

9. To stop auger, release auger drive clutch lever (right

hand -- Figure 11).

10. To move the snowthrower backwards, move speed select

lever into first or second reverse and engage traction

drive clutch lever (left hand). To stop, release traction

drive clutch lever.

WARNING: Read Owner’s Manual before oper-

ating machine. This machine can be dangerous

if used carelessly.

Never operate the snowthrower without all guards, cov-

ers, and shields in place.

Never direct discharge towards windows or allow by-

standers near machine while engine is running.

Stop the engine whenever leaving the operating posi-

tion.

Disconnect spark plug before unclogging the impeller

housing or the discharge chute and before making re-

pairs or adjustments.

When leaving the machine, remove the ignition key.

To reduce the risk of fire, keep the machine clean and

free from spilled gas, oil and debris.

Remote Chute

Lever

Electric Chute

Switch

Speed Select

Lever Auger Drive

Clutch Lever

Heated Hand

Grip Switch

5. To engage Free-Hand control, BOTH levers must be

depressed. Free-Hand control allows you to operate

the other snowthrower controls by releasing either the

left or right lever. Release both levers to disengage

Free-Hand control.

Figure 11

Traction Drive

Clutch Lever

Not for

Reproduction

OPERATION

18

BEFORE STARTING ENGINE

Check the oil

NOTE: The engine was shipped from the factory filled

with oil. Check the level of the oil. Add oil as needed.

1. Make sure the unit is level. Use a high quality detergent

oil classified “For Service SG, SH, SJ, SL, or higher”.

2. Remove the oil fill cap/dipstick and wipe with a clean

cloth (see Figure 12).

3. Insert the oil fill cap/dipstick and turn clockwise to tighten.

4. Remove the oil fill cap/dipstick and check the oil.

NOTE: Do not check the level of the oil while the

engine runs.

5. If necessary, add oil until the oil reaches the FULL mark

on the oil fill/cap dipstick (see Figure 12). Do not add too

much oil.

6. Tighten the fill cap/dipstick securely each time you check

the oil level.

NOTE: For extreme cold operating conditions of 0°F

(--18°C) and below, use a synthetic 5W30 motor oil for

easier starting.

NOTE: S.A.E. 5W30 motor oil may be used to make

starting easier in areas where the temperature is 20°F.

(--7°C)to0°F(--18°C). Synthetic 5W30 is acceptable for

all temperatures. DO NOT mix oil with gasoline.

NOTE: SEE CHART FOR OIL RECOMMENDATION

0°F(--18°C) and below

0°F(--18°C) and above

TYPE OF OILTEMPERATURE

synthetic 5W30

S.A.E. 5W30

°F -20 0 20 32 40

°C --30 --20 --10 0 10

SAE VISCOSITY GRADES

5W30

synthetic 5W30

FILL GAS

This engine is certified to operate on gasoline. Exhaust

Emission Control System: EM (Engine Modifications).

1. Fill the fuel tank with fresh, clean, unleaded regular, un-

leaded premium, or reformulated automotive gasoline

with a minimum of 85 octane along with a fuel stabilizer

(follow instructions on fuel stabilizer package). DO NOT

use leaded gasoline. We recommend that fuel stabilizer

be added to the fuel each time that gasoline is added to

the fuel tank.

NOTE: Winter grade gasoline has higher volatility to

improve starting. Be certain container is clean and

free from rust or other foreign particles. Never use

gasoline that may be stale from long periods of

storage in the container.

2. Check to make sure that spark plug is tightened securely

into engine and spark plug wire is attached to spark plug.

If torque wrench is available, torque plug to 18--23 ft--lbs.

WARNING: Gasoline is flammable. Always use

caution when handling or storing gasoline. Do

not add gasoline to the fuel tank while snow

blower is running, hot, or when snowthrower is in an en-

closed area. Keep away from open flame, electrical

sparks and DO NOT SMOKE while filling the fuel tank.

Never fill the fuel tank completely; but fill the fuel tank

to within 1-1/2 inch (3.8 mm) from the top to provide

space for the expansion of the fuel. Always fill fuel tank

outdoors and use a funnel or spout to prevent spilling.

Make sure to wipe up any spilled fuel before starting

the engine.

Store gasoline in a clean, approved container, and keep

the cap in place on the container. Keep gasoline in a

cool well ventilated place; never in the house. Never

buy more than a 30 day supply of gasoline to assure

volatility. Gasoline Is intended to be used as a fuel for

internal combustion engines; therefore, do not use

gasoline for any other purpose. Since many children

like the smell of gasoline, keep it out of their reach be-

cause the fumes are dangerous to inhale, as well as be-

ing explosive.

FULL

Figure 12

Oil Fill Cap/Dipstick

Fuel Tank

BEFORE STOPPING THE ENGINE

Run the engine for a few minutes to help dry off any moisture

on the engine.

Fuel Gauge

Not for

Reproduction

OPERATION

19

TO STOP ENGINE

TO START ENGINE

1. Check the oil level. See the Engine Manual

How

to Check/Add Oil

section

2. Make sure equipment drive controls are

disengaged.

3. Move the throttle lever (A, Figure 14 ) to the fast

position. Always operate the engine with the throttle

control lever in the fast position.

4. Push in the safety key (B, Figure 14 ).

5. Turn the choke control knob (C) to the choke position.

Figure 14. Starting the Engine

A. Throttle Lever

B. Safety Key

C. Choke Control Knob

D. Primer Button

Note: Do not use the choke to start a warm engine.

6. Push the primer button (D) two times.

Note: Do not use the primer to start a warm engine.

Figure 15. Rewind Start

A. Starter Cord Handle

WARNING

Rapid retraction of the starter cord (kickback)

will pull your hand and arm toward the engine

faster than you can let go. Broken bones,

fractures, bruises or sprains could result.

When starting engine, pull the starter cord

slowly until resistance is felt and then pull

rapidly to avoid kickback.

7. Rewind Start: Firmly hold the starter cord handle

(A, Figure 15). Pull the starter cord handle slowly

until resistance is felt, then pull rapidly.

WARNING

Gasoline and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns or

death.

DO NOT choke the carborator to stop the

engine.

1. Move the throttle control lever (A, Figure 13 ) to the

slow position, then to the stop position (B).

2. Remove the safety key (C). Keep the safety key

out of reach of children.

Figure 13. Stopping the Engine

A. Throttle Control Lever

B. Stop Position

C. Safety Key

A

B

C

A

B

C

D

2X

A

Not for

Reproduction

OPERATION

20

Figure 16. Electric Start

A. Starter Push Button

B. Power Cord Receptacle

A

B

Note: If the engine does not start after three attempts,

see the Engine Manual Troubleshooting section.

8. Electric Start: First connect the extension cord to

the power cord receptacle and then into a wall

receptacle. If additional extension cord is

required, make sure it is 3-wire.

WARNING

If the extension cord is damaged, it must be

replaced by the manufacturer or its service

agent or a similarly qualified person to avoid to

avoid a hazard.

9. Electric Start: Depress the push button (A, Figure

16). After you start the engine, first disconnect the

extension cord from the wall receptacle and then

from the power cord receptacle (B).

10.Allow the engine to warm up for several minutes.

Then slowly move the choke control knob to the

CAUTION

To extend the life of the starter, use short

starting cycles (five seconds maximum). Wait

one minute between starting cycles.

Note: If the engine does not start after three attempts,

see the Engine Manual Troubleshooting section.

run position.

Not for

Reproduction

La page charge ...

Simplicity SEARS CRAFTSMAN SNOWTHROWER, 13.5 TP, 27 INCH Manuel utilisateur

Simplicity SEARS CRAFTSMAN SNOWTHROWER, 13.5 TP, 27 INCH Manuel utilisateur

dans d''autres langues