PW 6241 D
en Installation Plan Commercial Washing Machine
fr Schéma d’installation Machine à laver professionnelle
M.-Nr. 12 168 550
en-US, fr-CA
en - Contents
3
Installation notes............................................................................................................. 4
Explanation of the safety notes and warnings on the machine......................................... 4
Installation requirements ................................................................................................... 4
General operating conditions ............................................................................................ 4
Installation ......................................................................................................................... 4
Electrical connection......................................................................................................... 5
Water connection .............................................................................................................. 6
Cold-water connection.................................................................................................. 6
Hot water connection.................................................................................................... 7
Hard water connection.................................................................................................. 7
Drain valve..................................................................................................................... 7
Dispenser pump connections ........................................................................................... 8
Optional accessories......................................................................................................... 9
Payment system kit (BSK)............................................................................................. 9
Peak-load negotiation kit (BSS) .................................................................................... 9
XKM RS232 communication module............................................................................ 10
Vapor and suds venting kit (APWM063)....................................................................... 10
Installation........................................................................................................................ 11
Installation (indirect steam heating)................................................................................... 11
Installation........................................................................................................................ 13
Dimensions........................................................................................................................ 13
Standard floor anchoring................................................................................................... 14
Technical details.............................................................................................................. 15
Electrical version and electrical data................................................................................. 15
Connection for equipotential bonding .......................................................................... 15
Steam connection ............................................................................................................. 15
Water connections ............................................................................................................ 15
Cold water connection.................................................................................................. 15
Hot water connection.................................................................................................... 16
Hard water connection.................................................................................................. 16
Condensate connection (indirect steam heating only).................................................. 16
Waste water (drain valve) .............................................................................................. 16
Securing the machine........................................................................................................ 16
Fasteners....................................................................................................................... 16
Emissions .......................................................................................................................... 16
Appliance data .................................................................................................................. 17
Transport data ................................................................................................................... 17
en - Installation notes
*INSTALLATION*
4
Explanation of the safety notes and warnings on the ma-
chine
Read the operating instructions
Read all the instructions, e.g., the installation instruc-
tions
Warning, hot surfaces
Warning, voltage up to 1000volts
Grounding
Equipotential bonding
Installation requirements
The washing machine must be installed by Miele Service or by
properly trained staff of an authorized dealer.
This washing machine must be installed in accordance with all rel-
evant regulations and standards. Local energy supplier regulations
must also be observed.
This washing machine must only be operated in a room that has
sufficient ventilation and which is frost-free.
The washing machine should not be installed or operated in any
area where there is a risk of explosion.
General operating conditions
This washing machine is intended only for use in a commercial envi-
ronment and must only be operated indoors.
- Ambient temperature: 32-105°F (0-40°C)
- Relative humidity: non-condensing
- Maximum height above sea level of location site: 6500 ft (2000 m)
Depending on the nature of the installation site, sound emissions and
vibration may occur.
Tip: Have the installation site inspected and seek the advice of a spe-
cialist in instances where increased noise may cause a nuisance.
Installation
This washing machine must be transported to its installation site us-
ing a suitable pallet truck. Remove the transport packaging.
en - Installation notes
*INSTALLATION*
5
The washing machine must be set up on a completely level, horizon-
tal, and firm surface with the minimum stated load bearing capacity
(see “Technical data”).
Tip: A concrete floor is the most suitable installation surface for this
machine. It is far less prone to vibration during the spin cycle than
wooden floorboards or a carpeted surface.
The floor load created by the washing machine is the load exerted
by the area of the machine in contact with and transferred to the in-
stallation surface.
The washing machine requires a gap of at least 2" (50mm) on each
side to allow for movement during operation. Please ensure a mini-
mum distance of 15 3/4" (400mm) is maintained between the rear of
the appliance and the rear wall.
The washing machine must not be installed on a carpeted floor.
The feet of the washing machine must be secured to the fastening
points on the floor using the fixtures and fastenings supplied.
The material provided is intended for use in bolting the machine to a
concrete floor. If other floor types are present at the installation site,
the fixtures and fastenings must be provided by the customer.
Electrical connection
The electrical connection must only be carried out by a qualified
electrician who must ensure that all electrical work is carried out in
accordance with applicable electrical regulations and standards.
The washing machine must be connected to an electrical supply
that complies with local and national regulations. Please also observe
your insurance and energy supplier's regulations as well as any health
and safety at work regulations.
The required voltage, power consumption and specifications for
external fusing are quoted on the data plate on the washing machine.
Ensure that the supply voltage complies with the voltage quoted on
the data plate before connecting the washing machine to the power
supply.
Connection to a supply voltage other than the one quoted on the
data plate can lead to functional faults and damage the washing
machine.
If more than one voltage is quoted on the data plate, the washing
machine can be converted for connection to the voltages stated.
Conversion to a different voltage must only be carried out by a
Miele Service engineer or by an authorized Service Dealer. The wiring
instructions given on the wiring diagram must be followed.
en - Installation notes
*INSTALLATION*
6
The washing machine can either be hard-wired or connected via a
plug and socket that complies with national codes and regulations.
For a hard-wired connection an all-pole isolation device must be in-
stalled on site.
For hard-wired machines connection should be made via a suitable
switch with all-pole isolation which, when in the off position, ensures
a 1/8" (3 mm) gap between all open contacts. These include circuit
breakers, fuses and relays.
If the power supply cannot be permanently disconnected, the isolator
switch (including plug and socket) must be safeguarded against be-
ing switched on either unintentionally or without authorization.
Tip: We recommend connection to the power supply via a suitable
plug and socket which must be easily accessible for servicing and
maintenance work after the machine has been installed.
If it is necessary to install a residual current device (RCD) in accor-
dance with local regulations, a typeB residual current device (sensi-
tive to universal current) must be used.
An existing typeA residual current device (RCD) must be exchanged
for a typeB RCD.
Equipotential bonding must be in accordance with all national and
local regulations.
Accessories for equipotential bonding are not supplied and need to
be ordered separately.
Water connection
The washing machine complies with current local and national
safety regulations protecting the drinking water supply and can
therefore be connected to the drinking water supply without a non-
return valve.
The flow pressure must amount to a minimum of 100kPa (14.5psi)
and must not exceed an overpressure of 1,000kPa (145psi). If the
flow pressure is higher than 1,000kPa (145psi), a pressure reducing
valve must be used.
The machine must be connected to the water connection using the
water inlet hoses provided.
The connection points are subject to water connection pres-
sure.
Turn on the water supplies slowly and check for leaks. Correct the
position of the seal and screw thread if appropriate.
Cold-water con-
nection
For the cold-water connection one shut-off valve each with a
¾" external thread is required. A connector (Y-piece) can be used if
required to connect 2water inlet hoses with a ¾" screw thread to a
single faucet with a 1" male thread.
en - Installation notes
*INSTALLATION*
7
The water inlet hose for cold water (blue stripes) is not intended to
be used with a hot-water connection.
Hot water con-
nection To minimize energy consumption during operation with hot water,
the washing machine should be connected to a suitable hot water
ring circuit if present.
So-called “transmission lines” (single lines to hot water generators)
can result in cooling down of the water remaining in the pipes if not
in constant use. More electrical energy would be needed in order to
heat the suds.
Use the water inlet hose supplied (red stripes) for the hot water con-
nection.
The temperature of the hot water intake must not exceed 158 °F
(70 °C).
If there is no hot water supply at the installation location, the hot wa-
ter inlet hose must also be connected to the cold water supply. An
additional Y-piece is required in this case. Cold water consumption of
the washing machine increases accordingly to account for the miss-
ing hot water inlet.
For functional and technical reasons it is not possible to operate
the machine exclusively with a hot water connection.
Even if a hot water connection is present, the washing machine
must be connected to a cold water inlet.
Hard water con-
nection
For the hard water connection, the same requirements apply as for
the cold water connection.
If there is no hard water connection on site, the hose must be con-
nected to the cold water connection.
Drain valve In the case of washing machines with a drain valve, a motorized valve
is used to drain the machine. A 2¾" angle connector can be used for
connecting the drain valve directly into the waste water system (with-
out a siphon) or into a floor drain (on-site gully with odor trap).
Thanks to an improved closing mechanism and a larger cross-sec-
tion, even the coarsest of soil does not leave any deposits or debris
behind which could result in blockages. The drain valve can also be
operated manually to allow the suds container to be emptied in the
event of a power failure.
A vented drainage system is vital for unimpeded drainage.
If several machines are connected to a single drain pipe, this
should be sufficiently large to allow all machines to drain simultane-
ously.
If the slope for drainage is extremely steep, the piping must be
vented to prevent formation of a vacuum in the machine’s drainage
system.
en - Installation notes
*INSTALLATION*
8
Slow or obstructed drainage or a backup of water in the drum as a re-
sult of undersized pipework can result in faults occurring during pro-
gram sequences, which will result in fault messages appearing in the
machine display.
Outflowing suds can be as hot as 203°F (95°C). Danger of injury
by burning!
Avoid direct contact.
Dispenser pump connections
Up to 12dispenser pumps can be connected to the washing ma-
chine.
Dispenser pump connections on the back of the machine
Connections 1 and 2 are provided for viscous agents and can also be
used for high-pressure dispensing systems with water injection.
These connectors are sealed and need to be drilled open using an
8mm drill bit before connecting.
Care must be taken to drill through the first wall only (I) as there is a
deflecting panel(II) 3/8"(10mm) behind it.
Connections3 to 12 are for liquid detergent. These connectors are
sealed and must be cut to the diameter of the hose with a small saw.
If opened connectors are no longer required, they must be resealed
using a suitable sealant (e.g., silicone).
Connection terminals for five time-controlled dispenser pumps, which
can be operated without a multifunction module, are located behind
the cover adjacent to the electrical connection.
en - Installation notes
*INSTALLATION*
9
Calibration of the dispenser pumps and regulation of dispensing
quantities is carried out semi-automatically for washing machines
fitted with an optional multifunction module. Information regarding
settings is given in the operating instructions.
A flowmeter or flow sensors can be connected for precise monitoring
of the dispensing quantity.
Connections for level monitoring are available for every agent dis-
pensed.
Optional accessories
Only use genuine Miele spare parts and accessories with this ma-
chine.
Using parts or accessories from other manufacturers will void the
warranty, and Miele cannot accept liability.
Payment system
kit (BSK)
The washing machine can be equipped with a payment system (e.g.,
for self-service operations) using the optional BSK payment system
kit. This must be connected and programmed by Miele Technical Ser-
vice. Payment systems with mechanical or electronic coin validator
are available from Miele as optional accessories for individual target
groups.
The programming required for connecting a payment system must
be carried out by Miele Technical Service or an authorized
Mieledealer only. An external power supply is not required for a pay-
ment system.
Peak-load negoti-
ation kit (BSS)
The washing machine can be connected to an energy management
system via a peak-load negotiation kit which is available as an op-
tional accessory.
Peak-load negotiation monitors the energy consumption of a system
and deactivates individual pieces of equipment temporarily in order
to ensure that certain total load limits are not exceeded. Monitoring
is externally controlled.
The kit provides three signal contacts and a neutral conductor via a
terminal block. The terminal block is marked with “a”, “b”, “c”, and
“d”:
aOutput signal, start of machine operation
bOutput signal, machine heating request
en - Installation notes
*INSTALLATION*
10
cPeak-load input signal, machine heating deactivated
dNeutral conductor
When the peak-load function is activated the current program is
stopped and a message appears in the display on the washing ma-
chine. The program is resumed automatically when the peak-load
system reactivates the heating.
XKM RS232 com-
munication mod-
ule
The serial interface RS-232 can be retrofitted to the washing machine
via an XKMRS232 (optional accessory available from Miele). This
communication module must only be used with MieleProfes-
sionalmachines that are fitted with an appropriate slot for the mod-
ule.
The data interface provided via communication module
XKMRS232 complies with SELV (Safety Extra Low Voltage) in ac-
cordance with EN60950.
Machines connected to this interface must also be SELV compliant.
Communication module XKMRS232 is supplied with a connection
cable and a D-sub-connector.
Vapor and suds
venting kit
(APWM063)
If excessive suds form, suds may escape from the vapor vent. An op-
tional vapor and foam venting kit can be used to remove the foam.
en - Installation
11
Installation (indirect steam heating)
aElectrical connection
bCold-water connection
cHot-water connection
dCold-water connection (alternatively,
hard-water connection)
eCold-water connection for liquid dispens-
ing (optional)
fDispenser pump connections
gOverflow
hCommunication connection
iDrain pipe
kSI connection, intake SI only
lSI connection, drain SI only
oSteam valve SI only
en - Installation
12
aElectrical connection
bCold-water connection
cHot-water connection
dCold-water connection (alternatively,
hard-water connection)
eCold-water connection for liquid dispens-
ing (optional)
fDispenser pump connections
gOverflow
hCommunication connection
iDrain pipe
jConnection for grounding
kSI connection, intake SI only
lSI connection, drain SI only
nSteam valve connection SI only
en - Installation
*INSTALLATION*
13
Dimensions
en - Installation
*INSTALLATION*
14
Standard floor anchoring
screw/anchor point
en - Technical details
15
Electrical version and electrical data
Connection voltage 208/240 V3 Ph
Frequency 60 Hz
Total amps. 11 A
Max. fuse (time delay fuse) 15 A
Minimum circuit ampacity 11 A
Connection voltage 240 V1 Ph 3 Wire
Frequency 60 Hz
Total amps. 27 A
Max. fuse (time delay fuse) 30 A
Minimum circuit ampacity 27 A
Miele recommends connecting the machine via a wall socket with an all-pole means of deactivation and interlock.
The wall socket or isolator must remain accessible at all times once the machine has been installed.
To increase safety, Miele recommends installation of a residual current device (RCD). Only use residual current devices that are sensi-
tive to universal current (typeB).
Connection for equipotential bonding
Connection with male thread (machine) 3/8"x13/16" (10mmx30mm)
Size of washers and nuts M10
An equipotential bond with good contact connection must always be provided in accordance with all national and local regulations.
Steam connection
Indirect steam heating
Steam overpressure 58-145 psi (400–1,000kPa)
Boiling point 306-363°F (152–184°C)
Steam heating power 170607 BTU/h
Mass flow (peak capacity) 185 lb/h (84kg/h)
Threaded union (on site) ½"female thread
Steam solenoid valve, dirt filter, and steam shut-off valve must be installed by the customer on site. Follow the installation instructions
for steam-heated machines.
Water connections
Cold water connection
Required flow pressure 14.5-145 psi (1–10 bar)
Maximum flow rate (if no hot water and hard water supply) 19.5 (21*) gpm / 74 (79.5*) l/min
Maximum flow rate 6.8 (8.3*) gpm / 26 (31.5*) l/min
Threaded union required (male thread, to be provided by customer in accordance with
DIN44991, flat sealing)
3/4"
Length of water inlet hose supplied 2 (3*) x 61" (1550 mm)
*With liquid dispensing
en - Technical details
16
Hot water connection
Maximum permissible hot water temperature 158°F (70°C)
Required flow pressure 14.5-145 psi (1–10 bar)
Maximum flow rate 4.5 gpm (16 l/min)
Threaded union required (male thread, to be provided by customer in accordance with
DIN44991, flat sealing)
3/4"
Length of water inlet hose supplied 1 x 61" (1550 mm)
Hard water connection
Required flow pressure 14.5-145 psi (1–10 bar)
Maximum flow rate 8.5 gpm (32 l/min)
Threaded union required (male thread, to be provided by customer in accordance with
DIN44991, flat sealing)
3/4"
Length of water inlet hose supplied 2 x 61" (1550 mm)
Condensate connection (indirect steam heating only)
Threaded union for condensate connection (on site) ½"female thread
Condensate trap, dirt filter, and steam shut-off valve must be installed by the customer on site.
Waste water (drain valve)
Maximum waste water temperature 203°F (95°C)
Machine-side drain connection (external diameter) HT DN 70 (2 15/16")
On-site drain (internal diameter) 2 15/16" x 13/16" x 4 5/16" (75 x 1.9 x
110 mm sleeve DN 70)
Maximum flow rate 52.8 gpm (200 l/min)
A vented combined pipe is required to drain the waste water. If several machines are connected to a single drain pipe, this should be
sufficiently large to allow all machines to drain simultaneously.
Securing the machine
Fasteners
4x wood screws DIN571 (Øxlength) 12 mm x 90 mm
4x plugs (Øxlength) 16 mm x 80 mm
Fixing the machine in place is absolutely essential.
Emissions
Average heat dissipation rate to installation site 4.7 MJ/h
A-weighted noise power level in accordance with EN ISO 9614, part 2 78 dB(A) re 20 µPa
Sound power level, washing 60.3 dB (A) re 1 pW
Sound power level, spinning 82.2 dB (A) re 1 pW
en - Technical details
17
Appliance data
Appliance width 42 3/4" (1085 mm)
Appliance height 64 11/16" (1643 mm)
Appliance depth 43 9/16" (1106 mm)
Appliance width, total 42 7/8" 1(089 mm)
Appliance height, total 64 13/16" (1646 mm)
Appliance depth, total 51 1/2" (1308 mm)
Width of loading aperture (internal width) 6 5/8" (1185 mm)
Recommended wall spacing (up to the front edge of the appliance) 70 7/8" (1800 mm)
Net weight 1521 lb (690 kg)
Maximum floor load in operation 8417 N
Maximum static load 7063 N
Maximum dynamic load 1353 N
Maximum rotation frequency of drum 18.3 Hz
Installation should only be performed by qualified installers in accordance with local
codes and standards.
Transport data
Packaging width 49 5/8" (1260 mm)
Packaging height 67 5/16" (1710 mm)
Packaging depth 57 7/8" (1470 mm)
Gross weight 1631 lb (740 kg)
fr - Table des matières
18
Remarques sur l’installation........................................................................................... 19
Explication des consignes de sécurité et des avertissements sur l’appareil .................... 19
Conditions d’installation.................................................................................................... 19
Conditions de fonctionnement générales ......................................................................... 19
Installation ......................................................................................................................... 20
Raccordement électrique.................................................................................................. 20
Raccordement à l’eau ....................................................................................................... 21
Raccordement à l’eau froide......................................................................................... 22
Raccordement à l’eau chaude ...................................................................................... 22
Raccordement à l’eau dure........................................................................................... 22
Vanne de vidange.......................................................................................................... 23
Raccordements pour pompes de dosage......................................................................... 23
Accessoires en option....................................................................................................... 24
Kit de monnayeur (BSK)................................................................................................ 24
Kit de gestion des charges de pointe (BSS) ................................................................. 25
Module de communication XKMRS232....................................................................... 25
Kit d’évacuation de vapeur et de mousse (APWM063) ............................................... 26
Installation........................................................................................................................ 27
Installation (chauffage vapeur indirect).............................................................................. 27
Installation........................................................................................................................ 29
Dimensions........................................................................................................................ 29
Ancrage standard dans le sol............................................................................................ 30
Données techniques ....................................................................................................... 31
Plages de tension et données électriques ........................................................................ 31
Raccordement pour liaison équipotentielle................................................................... 31
Raccordement à la vapeur ................................................................................................ 31
Raccordements à l’eau ..................................................................................................... 31
Raccordement à l’eau froide......................................................................................... 31
Raccordement à l’eau chaude ...................................................................................... 32
Raccordement à l’eau dure........................................................................................... 32
Raccord du condensat (vapeur indirecte chauffage uniquement) ................................ 32
Eaux usées (vanne de vidange)..................................................................................... 32
Fixation de l’appareil ......................................................................................................... 32
Raccords....................................................................................................................... 32
Émissions .......................................................................................................................... 32
Données de l’appareil........................................................................................................ 33
Données de transport........................................................................................................ 33
fr - Remarques sur l’installation
*INSTALLATION*
19
Explication des consignes de sécurité et des avertisse-
ments sur l’appareil
Lire le mode d’emploi
Lire toutes les instructions, parex. le plan de montage
Attention, surfaces très chaudes
Attention, tension jusqu’à 1 000volts
Mise à la terre
Liaison équipotentielle
Conditions d’installation
La machine à laver doit être installée et mise en service par un
technicien du service technique Miele ou par le personnel dûment
formé d'un revendeur agréé par la marque.
La machine à laver doit être installée conformément aux normes et
réglementations en vigueur. Les prescriptions du fournisseur d’éner-
gie local et des services des eaux doivent en outre être respectées.
Cette machine à laver ne doit être utilisée que dans une pièce suf-
fisamment ventilée et à l’abri du gel.
La machine à laver ne doit pas être installée ou utilisée dans une
zone présentant un risque d’explosion.
Conditions de fonctionnement générales
Cette machine à laver est conçue uniquement pour une utilisation en
intérieur et dans un environnement commercial.
- Température ambiante: 0-40 °C (32–105°F)
- Humidité relative: sans condensation
- Hauteur maximale au-dessus du niveau de la mer du site de l’em-
placement: 2000 m (6500pieds)
Selon la nature du site d’installation, des émissions sonores et des
vibrations peuvent survenir.
Conseil : Faire inspecter le site d’installation et faire appel à un pro-
fessionnel dans le cas où l’augmentation des émissions sonores de-
viendrait une nuisance.
fr - Remarques sur l’installation
*INSTALLATION*
20
Installation
Transporter la laveuse vers son lieu d’installation à l’aide d’un trans-
palette approprié et retirer l’emballage de transport.
La laveuse doit être installée sur une surface entièrement plane, hori-
zontale et solide qui résiste au moins à une charge au sol indiquée
(voir «Données techniques»).
Conseil : Un sol en béton est la surface d’installation la mieux adap-
tée pour cet appareil. En effet, il est moins sujet aux vibrations du
cycle d’essorage que les planchers en bois ou les sols recouverts
d’une moquette.
La charge créée sur le plancher par la laveuse est la charge exercée
par la zone de l’appareil en contact avec la surface d’installation et
est transférée sur cette dernière.
La laveuse nécessite un écart d’au moins 50mm (2") de chaque côté
pour permettre le mouvement durant le fonctionnement. S’assurer
qu’une distance minimum de 400mm (16") entre l’arrière de l’appareil
et le mur derrière est maintenue.
La laveuse ne doit pas être installée sur de la moquette.
Les pieds de la laveuse doivent être fixés au sol au niveau des points
de fixation à l’aide des raccords fournies.
Les raccords fournis servent à fixer l’appareil sur un sol en béton. Si
d’autres types de sol sont présents sur le lieu d’installation, le maté-
riel de fixation doit être commandé par le client.
Raccordement électrique
Le raccordement électrique doit être effectué uniquement par un
électricien qualifié conformément aux normes et réglementations
électriques en vigueur.
La machine à laver doit être raccordée à un système électrique
conforme aux réglementations nationales et locales. En outre, il
convient de respecter tous les règlements des entreprises de distri-
bution d’électricité et toutes les normes relatives à la sécurité, ainsi
que toutes les normes techniques et les réglementations en vigueur!
La tension réseau, la puissance raccordée et le calibre du fusible
sont indiqués sur la plaque signalétique de la machine à laver. Avant
de raccorder la machine à laver à l’alimentation électrique, s’assurer
que la tension réseau indiquée sur la plaque signalétique correspond
à celle de l’alimentation électrique principale.
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
