B&B MiniMc-Gigabit Series Mode d'emploi

Marque
B&B
Modèle
MiniMc-Gigabit Series
Catégorie
Convertisseurs de média réseau
Taper
Mode d'emploi
MiniMc-Gigabit
Operation Manual
ii
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A computing device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class A
limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe A
prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.
Limited Lifetime Warranty
Effective for products of B&B Electronics shipped on or after May 1, 2013, B&B Electronics warrants that each such
product shall be free from defects in material and workmanship for its lifetime. This limited lifetime warranty is
applicable solely to the original user and is not transferable.
This warranty is expressly conditioned upon proper storage, installation, connection, operation and maintenance of
products in accordance with their written specifications.
Pursuant to the warranty, within the warranty period, B&B Electronics, at its option will:
1. Replace the product with a functional equivalent;
2. Repair the product; or
3. Provide a partial refund of purchase price based on a depreciated value.
Products of other manufacturers sold by B&B Electronics are not subject to any warranty or indemnity offered by B&B
Electronics, but may be subject to the warranties of the other manufacturers.
Notwithstanding the foregoing, under no circumstances shall B&B Electronics have any warranty obligations or any
other liability for: (i) any defects resulting from wear and tear, accident, improper use by the buyer or use by any third
party except in accordance with the written instructions or advice of the B&B Electronics or the manufacturer of the
products, including without limitation surge and overvoltage conditions that exceed specified ratings, (ii) any products
which have been adjusted, modified or repaired by any party other than B&B Electronics or (iii) any descriptions,
illustrations, figures as to performance, drawings and particulars of weights and dimensions contained in the B&B
Electronics’ catalogs, price lists, marketing materials or elsewhere since they are merely intended to represent a general
idea of the products and do not form part of this price quote and do not constitute a warranty of any kind, whether
express or implied, as to any of the B&B Electronics’ products.
THE REPAIR OR REPLACEMENT OF THE DEFECTIVE ITEMS IN ACCORDANCE WITH THE EXPRESS WARRANTY SET
FORTH ABOVE IS B&B ELECTRONIC’ SOLE OBLIGATION UNDER THIS WARRANTY. THE WARRANTY
CONTAINED IN THIS SECTION SHALL EXTEND TO THE ORIGINAL USER ONLY, IS IN LIEU OF ANY AND ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND ALL SUCH WARRANTIES AND INDEMNITIES ARE EXPRESSLY
DISCLAIMED, INCLUDING WITHOUT LIMITATION (I) THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR
PURPOSE AND OF MERCHANTABILITY AND (II) ANY WARRANTY THAT THE PRODUCTS ARE DO NOT INFRINGE
OR VIOLATE THE INTELLECTUAL PROPERTY RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL B&B
ELECTRONICS BE LIABLE FOR LOSS OF BUSINESS, LOSS OF USE OR OF DATA INTERRUPTION OF BUSINESS,
LOST PROFITS OR GOODWILL OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES.
B&B ELECTRONIC SHALL DISREGARD AND NOT BE BOUND BY ANY REPRESENTATIONS, WARRANTIES OR
INDEMNITIES MADE BY ANY OTHER PERSON, INCLUDING WITHOUT LIMITATION EMPLOYEES, DISTRIBUTORS,
RESELLERS OR DEALERS OF B&B ELECTRONIC WHICH ARE INCONSISTENT WITH THE WARRANTY, SET FORTH
ABOVE.
iii
Table of Contents
FCC Radio Frequency Interference Statement .................................................... ii
Limited Lifetime Warranty .................................................................................. ii
About the MiniMc-Gigabit ................................................................................. 1
LED Operation .................................................................................................. 1
Specifications .................................................................................................... 2
Fiber Optic Cleaning Guidelines ........................................................................ 3
Electrostatic Discharge Precautions .................................................................... 4
Safety Certifications ........................................................................................... 5
1
About the MiniMc-Gigabit
The MiniMc-Gigabit is a Gigabit Ethernet, miniature media converter. This device
converts 1000Base-SX (multi-mode) or LX (single-mode) fiber to 1000Base-T
copper, and always operates at Full-Duplex. Single strand fiber versions are also
available.
The MiniMc-Gigabit offers plug-and-play operation, including the AutoCross
feature which automatically selects between a crossover workstation or straight-
through repeater hub connection depending on the connected device.
The MiniMc-Gigabit installs in an B&B Electronics IE-PowerTray/18 or can be
used as a standalone media converter. As a standalone, the MiniMc-Gigabit uses
a universal external switching power cube with 100 - 240 ±10% V AC input and
5V DC output.
Installation Tip
Several models of the MiniMc-Gigabit support single-strand fiber for operation.
Since single-strand fiber products use optics that transmit and receive on two
different wavelengths, single-strand fiber products must be deployed in pairs. For
example, connect MiniMc-Gigabit TX/SSLX-SM1310-SC, which transmits at 1310
nm and receives at 1550 nm, to an iMcV-Gigabit TX/SSLX-SM1550-SC, which
transmits at 1550 nm and receives at 1310 nm. The two connected products
must also have the same speed and distance capabilities (i.e. both are single-
mode [20 km] or both are single-mode/PLUS [40 km]).
NOTE
Use only the supplied B&B Electronics
p
ower suppl
y
. Using a non-B&B
Electronics power source will void the warranty.
LED Operation
Each MiniMc-Gigabit includes two LEDs, located on the RJ45 connector LED
functions are as follows:
FX LNK
Glows green when a link is established on the fiber port.
TX LNK/ACT
Glows amber when a link is established on the copper port; blinks amber
when activity is detected on the copper port.
2
Specifications
AC Wall Adapter
100 to 240 ±10% V AC input, 5V DC output, 2A max.
Power Consumption (Typical):
600 mA @ 5V
Operating Temperature:
32° to 122° F (0° to 50° C)
Storage Temperature:
-4° to 158°F (-20° to 70° C)
Humidity:
5 to 90% (non-condensing); 0 to 10,000 ft. altitude
Dimensions:
0.83”H x 1.80”W x 3.35”D (2.1cm x 4.6cm x 8.5cm)
3
B&B Electronics Technical Support
Tel:
(800) 346-3119 (in the U.S. and Canada)
Monday-Friday, 7:00am-7”00pm CST
+353 91 792444 (Europe)
Monday through Friday 8:00am - 5:00pm GMT
Fax:
(815) 433-5109 U.S. and Canada
+353 91-79244S5 Europe
E-Mail:
[email protected] U.S. and Canada
[email protected] Europe
Web:
www.bb-elec.com
Fiber Optic Cleaning Guidelines
Fiber Optic transmitters and receivers are extremely susceptible to contamination
by particles of dirt or dust, which can obstruct the optic path and cause
performance degradation. Good system performance requires clean optics and
connector ferrules.
1.
Use fiber patch cords (or connectors, if you terminate your own fiber) only
from a reputable supplier; low-quality components can cause many hard-to-
diagnose problems in an installation.
2.
Dust caps are installed at B&B Electronics to ensure factory-clean optical
devices. These protective caps should not be removed until the moment of
connecting the fiber cable to the device. Should it be necessary to
disconnect the fiber device, reinstall the protective dust caps.
3.
Store spare caps in a dust-free environment such as a sealed plastic bag or
box so that when reinstalled they do not introduce any contamination to the
optics.
4.
If you suspect that the optics have been contaminated, alternate between
blasting with clean, dry, compressed air and flushing with methanol to
remove particles of dirt.
4
Electrostatic Discharge Precautions
Electrostatic discharge (ESD) can cause damage to any product, add-in modules
or stand alone units containing electronic components. Always observe the
following precautions when installing or handling these kinds of products
1.
Do not remove unit from its protective packaging until ready to install.
2.
Wear an ESD wrist grounding strap before handling any module or
component. If the wrist strap is not available, maintain grounded contact
with the system unit throughout any procedure requiring ESD protection.
3.
Hold the units by the edges; do not touch the electronic components or gold
connectors.
4.
After removal, always place the boards on a grounded, static-free surface,
ESD pad or in a proper ESD bag. Do not slide the modules or stand alone
units over any surface.
WARNING!
Integrated circuits and fiber optic components are
extremely susceptible to electrostatic discharge damage. Do not
handle these components directly unless you are a qualified service
technician and use tools and techniques that conform to accepted
industry practices.
5
Safety Certifications
UL/cUL: Listed to Safety of Information Technology Equipment, including
Electrical Business Equipment.
CE: The products described herein comply with the Council Directive
on Electromagnetic Compatibility (2004/108/EC) and the Council
Directive on Electrical Equipment Designed for use within Certain
Voltage Limits (2006/95/EC). Certified to Safety of Information
Technology Equipment, Including Electrical Business Equipment.
For further details, contact B&B Electronics.
European Directive 2002/96/EC (WEEE) requires that any equipment that bears
this symbol on product or packaging must not be disposed of with unsorted
municipal waste. This symbol indicates that the equipment should be disposed of
separately from regular household waste. It is the consumer’s responsibility to
dispose of this and all equipment so marked through designated collection
facilities appointed by government or local authorities. Following these steps
through proper disposal and recycling will help prevent potential negative
consequences to the environment and human health. For more detailed
information about proper disposal, please contact local authorities, waste disposal
services, or the point of purchase for this equipment.
Class 1 Laser product, Luokan 1 Laserlaite,
Laser Klasse 1
,
A
pp
areil A’Laser de Classe 1
International Headquarters
B&B Electronics
707 Dayton Road
Ottawa, IL 61350 USA
Phone (815) 433-5100 — General Fax (815) 433-5105
Email: [email protected]
Website: www.bb-elec.com
European Headquarters
B&B Electronics
Westlink Commercial Park
Oranmore, Co. Galway, Ireland
Phone +353 91-792444 — Fax +353 91-79244S5
Email: techSupport@bb-elec.com
Website: www.bb-elec.com
© 2013 B&B Electronics. All rights reserved.
The information in this document is subject to change without notice. B&B Electronics assumes no responsibility for any
errors that may appear in this document. MiniMc-Gigabit is a trademark of B&B Electronics. Other brands or product
names may be trademarks and are the property of their respective companies.
Document Number 55-80730-00 A5 September 2013
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

B&B MiniMc-Gigabit Series Mode d'emploi

Marque
B&B
Modèle
MiniMc-Gigabit Series
Catégorie
Convertisseurs de média réseau
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Autres documents