HP DesignJet 110plus Printer series Guide de référence

DO NOT PRINT THIS PAGE!

Part number: C7796-90239

Languages: EFIGS

Size: A5

Paper: 80 g. recycling paper recommended, but we leave it up to each DC to use

the most cost efficient paper according to their Paper strategy.

Color: B+W

Binding: Saddle stitch

Pages: 132 + cover front and back.

Covers: 200 gr. recycling paper recommended, but we leave it up to ech DC to use

the most cost efficient paper according to their Paper strategy.

File: pdf format.

HP Designjet 110plus series

Quick reference guide

DO NOT PRINT THIS PAGE. THIS PAGE IS FOR REFERENCE ONLY!

QRG110plusnr.fm Page 1 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110 plus/110plus nr

Quick reference guide

Guide de référence rapide

Guida di riferimento rapido

Kurzübersicht

Guía de referencia rápida

1

How do I…?

How do I load sheets of paper? (general guidance).................................2

How do I load paper using the front path? .............................................3

How do I unload paper from the front path? ...........................................3

How do I load paper into the input tray?................................................4

How do I print on large sheets?.............................................................6

How do I load a roll of paper? .............................................................8

How do I unload a roll of paper?........................................................10

How do I replace ink cartridges?.........................................................11

The problem is…

The problem is a paper jam................................................................12

The problem is a roll of paper is jammed..............................................13

The problem is that the printer has stopped...........................................14

The problem is that the printer has not received the job ..........................15

The problem is… something else .........................................................16

Tell me about…

Tell me about the front panel...............................................................17

Tell me about the icons on the front panel.............................................18

Tell me about combinations of flashing icons.........................................19

Legal information

HP limited warranty statement .............................................................21

Regulatory notices .............................................................................24

More information

For more details of how to use your printer,

additional information about your printer (including

drivers and networking), and troubleshooting printer

problems, see the Using Your Printer CD or the on-

line help for the printer driver.

HP Designjet 110 plus/110plus nr—Quick Reference Guide

QRG110plusnr.fm Page 1 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

2

There are three ways of loading sheets of paper into the printer:

•The input tray at the front of the printer for multiple sheets of paper between

76×142mm (3×5.6inches) and 457×610 mm (18×24inches) (C+).

You can load up to 50 sheets of paper of 0.2 mm thickness (or 150 g/m²) in

the unextended tray, or 25 sheets of the same thickness in the extended tray.

Envelopes can also be loaded in the input tray.

•The front path for single sheets of paper between 110 × 205 mm

(4.3×8.1inches) and 625×1625mm (24.6×63.9inches) (A1 oversize).

•The rear path (upper slot) for single sheets of thick paper or other media

between 110×205 mm (4.3×8.1inches) and 625×1625mm

(24.6×63.9inches) (A1 oversize). The rear path (lower slot) is used for roll

input.

• The automatic roll feed enables you to load roll paper into the rear path. When

roll paper is loaded into the printer, it obstructs the paper path; therefore roll

paper must always be unloaded before printing on sheet paper (see page 8).

However the paper is loaded, it should always be loaded in portrait mode: the

leading edge of the paper should be the shorter edge.

The output tray extensions may be used to support sheets of paper up to 19 inches

in length. For sheets longer than 19 inches, close the output tray extensions and use

the extended input tray to support the paper as it emerges from the printer.

How do I load sheets of paper? (general guidance)

extensions

to support

paper

input tray

front path

rear

path

output tray

QRG110plusnr.fm Page 2 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

3

1. Place a single sheet of paper in the output tray, aligning it on the right of the

output tray, with the side that is to be printed on facing down. Do not stack

multiple sheets here.

2. Push the paper as far as it will go into the printer, maintaining its alignment to

the right.

3. Press the OK key (the upper right key) on the front panel.

The printer will check the alignment of the paper, and if it is misaligned, it will eject

the paper; in that case you will have to reload the paper.

How do I unload paper from the front path?

In case you want to change or remove the paper that you have loaded before

printing, for example to change the type of paper or to use a different input path:

• Press the Cancel and OK keys at the same time, to eject the paper.

How do I load paper using the front path?

QRG110plusnr.fm Page 3 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

4

How do I load paper into the input tray?

Note that the input tray should be extended only when necessary: when using

paper larger than Legal- or A4-size.

1. Remove the input tray.

2. Lift up the tray cover.

3. If the paper you are using is larger than Legal- or A4-size, move the small tab

in the centre towards the left so that you can lengthen the tray. Then let go of

the tab and pull the tray extension out as far as it will go.

4. Riffle the paper. This helps to prevent adjacent sheets of paper from sticking to

each other.

QRG110plusnr.fm Page 4 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

5

5. Slide the paper into the tray under the tray

cover, ensuring that it touches the sides of the

tray on the right and on the printer side.

6. Push in the small tab on the right of the tray so

that it fits snugly against the paper. Move the

larger tab on the left of the tray to the right so

that it too fits snugly against the paper.

7. Close the tray cover.

8. Lift up the output tray and insert the input tray

into the printer, keeping it straight and pushing it in as far as it will go. The left

inside corner must be aligned with the plastic paper tray guide.

9. Lower the output tray. Note that if the input tray is extended, it will extend out

beyond the output tray.

QRG110plusnr.fm Page 5 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

6

How do I print on large sheets?

The printer output system has several adjustable components. When printing on

large sheets of paper, it is important that you use the correct printer output

configuration. The following diagram shows adjustable parts of the printer output

system:

.

The table on the next page gives the output system configuration required for

various paper sizes.

Note:

• When using the main tray or roll feedback as source, make the necessary

adjustments to the output system to enable output to be stacked.

• If the output tray has prints stacked in it and you want to print from the roll feed,

empty the output tray and adjust it as necessary before printing.

...continued on next page...

4

5

6

1

2

3

QRG110plusnr.fm Page 6 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

7

Source Destination Width Length

1

23456

JIS B5 182mm 257mm

ANSI A 8.5" 11"

ISO A4 210mm 297mm

ARCH A 9" 12"

DIN C4 229mm 324mm

ISO B4 250mm 353mm

LEGAL 8.5" 14"

JIS B4 257mm 364mm

ISO A3 297mm 420mm

ANSI B 11" 17"

ARCH B 12" 18"

DIN C3 324mm 458mm

ANSI B+ 13" 19"

ISO B3 353mm 500mm

JIS B3 264mm 515mm

ANSI C 17" 22"

ISO A2 420mm 594mm

ARCH C 18" 24"

DIN C2 458mm 648mm

ISO B2 500mm 707mm

JIS B2 515mm 728mm

ISO A1 594mm 841mm

ANSI D 22" 34"

ARCH D 24" 36"

Custom Up to 24" Up to 12"

Custom Up to 24" Up to 18"

Custom Up to 24" Up to 24"

Custom Up to 24" Up to 36"

Custom Up to 24" > 36"

Media

Size

Position A3,... Closed DOWN

C-Size Tray Output Tray

A-Size

B-Size

C-Size

Closed N/A

UP

Position B4,... Closed DOWN Closed N/A

UP

N/A

UP

Position B4,... Position A3,... DOWN Closed N/A

UP

Position A3,...

Closed Closed UP

ClosedPosition A3,... DOWN

Position 17x22 Open

DOWN

Closed Closed UP Position A2,... Open

DOWN

Manual feed,

front or rear

Output Bin D-Size

DOWN

Closed Position Roll icon DOWN

DOWN

Closed Position Roll icon DOWN

Roll

accessory

Output Bin Custom Closed N/A

Closed N/A

QRG110plusnr.fm Page 7 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

8

Only one source of paper can be used by the printer at any one time, so if a roll

of paper is loaded in the printer and you want to print to a sheet of paper, you

must first unload the roll. The roll is automatically reloaded the next time printing

to the roll is requested.

You can cut a roll without unloading it by pressing the OK key (top right key on

the front panel); the paper first advances about 1 cm or 0.4 inch.

1. Set your application to pick paper from the roll feed.

2. Select Print from your application.

3. Load a roll of the required paper onto the spindle. Ensure that the roll is the

right way round and that the blue stop on the spindle is pushed in against the

paper.

4. Insert the spindle into its retaining slots, with the blue stop on the right and the

black stop on the left as seen from the rear of the printer.

If the paper is glossy, we recommend that you wear gloves to avoid smearing

the surface of the paper.

5. Make sure that the leading edge of the roll is straight and perpendicular to its

side edges and has no irregularities.

...continued on next page...

How do I load a roll of paper?

QRG110plusnr.fm Page 8 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

9

...continued from previous page...

6. Rewind any excess paper so that the paper is rolled tightly onto the spindle.

7. Insert the leading

edge of the paper into

the lower slot in the

rear of the printer.

Push the paper in until

it encounters

resistance, keeping

the sides of the paper

rolled tightly so that

the paper is not

skewed.

8. After emitting a

‘beep’, the printer will

take up the paper.

9. The printer will check

the alignment of the paper. If the paper is properly aligned, the roll icon will

appear on the display, indicating that the printer is ready to print.

If the paper is misaligned, the printer will eject the paper and the display will

show the misaligned and roll icons; you will have to reload the paper.

Repeat Step 6, so that the paper is tightly rolled onto the spindle.

How do I print on large sheets?

QRG110plusnr.fm Page 9 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

10

Important: Do not pull on the roll of paper once it is taken up by the printer,

that is, if there is any resistance.

There are two ways of unloading a roll of paper:

• If you want to unload the roll in order to feed a single sheet through the

printer, press the Cancel and OK keys on the front panel at the same time (see

below). If you later request printing to the roll, the Automatic Roll Feed will

then automatically reload the roll.

• If you want to unload the roll in order to completely remove it (for example,

you no longer wish to use this roll of paper):

1. Push the Eject button on the left roll feed support at the rear of the printer.

Avoid pressing the Eject button several times, as this can damage the paper.

2. Pull the roll towards you and remove the paper completely from the rear

paper path of the printer. The icons shown below will flash until the paper is

completely out, because if the paper is only partially removed, paper jams

may subsequently occur. Sometimes the paper may fall away from the rear

path by itself.

You do not need to remove the spindle from its supports in the printer.

How do I unload a roll of paper?

QRG110plusnr.fm Page 10 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

11

How do I replace ink cartridges?

1. Open the front hinged flap at the

right of the printer.

2. For each ink cartridge that needs to

be replaced:

• Gripping it by its shorter top

edges, lift the ink cartridge

vertically up and out of the

printer.

• Lower the new ink cartridge into

its slot until it clicks into place

and is quite secure.

3. Finally close the outer flap.

QRG110plusnr.fm Page 11 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

12

1. Try pressing the OK key (the upper right key) on the printer’s front panel.

If this doesn't solve the problem…

2. Turn off the printer.

3. Remove all media from the tray. Pull out any paper that is visibly stuck.

4. Lift the top cover and pull out any paper that may be stuck.

Be careful when you lift the cover not to damage or disturb any of the tubes or

other internal parts of the printer.

5. Remove the rear path carefully by pressing the buttons on each of its sides and

pulling it straight out. If you don’t pull it straight out, you may damage the

paper sensor.

Removing the rear path gives access to the inside of the printer from the rear.

Pull out any paper that may be stuck inside or is accessible from the rear.

Replace the rear path and make sure it fits securely.

6. Turn on the printer.

7. We recommend that after clearing a paper jam you align the printheads to

avoid problems of poor print quality. To align printheads, start HP Designjet

System Maintenance (see page 16) and select Align printhead.

Rear path

The problem is a paper jam

QRG110plusnr.fm Page 12 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

13

If paper from the roll is jammed:

1. Turn off the printer.

2. Check in all places where the roll could be trapped:

• Remove the front paper tray. This will allow you to see inside the printer

through a slot in the front. Release and remove any trapped paper that is

accessible.

• Lift the top cover, being careful not to damage or disturb any of the tubes or

other internal parts of the printer. If there is any paper trapped in the wheels

inside the printer, release and remove the paper.

• Remove the rear path by pressing the buttons on each of its sides and pulling

it straight out. If you don't pull it straight out, you may damage the paper

sensor. If there is any paper trapped in the rollers inside the printer, release

and remove the paper.

3. Once the paper jam has been cleared, replace any parts of the printer

(paper tray, top cover, rear path) that you have removed/opened, making

sure they fit securely.

4. Turn on the printer.

5. Before reloading the paper roll, you must trim the leading edge of the roll

such that this edge is perfectly straight and at right-angles to the sides of the

roll.

The problem is a roll of paper is jammed

QRG110plusnr.fm Page 13 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

14

The problem is that the printer has stopped

If the front panel looks like this and the yellow light

is flashing:

1. Open both parts of the hinged flap at the right

of the printer, lifting it right back so that you can

see the print carriage. Check that all packaging

material has been removed from around the

print carriage.

The carriage may move at this point. Wait until

it has stopped moving.

2. Check that the printhead cover is latched down.

The printer will not work if the latch is not

properly engaged.

3. Close the rear part and then the front part of the

hinged flap. The printer will not work if it is not

properly closed.

4. If the yellow light has not turned off, see the

Using Your Printer CD.

QRG110plusnr.fm Page 14 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

15

The problem is that the printer has not received the job

If your printer seems to be ignoring the printing job you have sent to it:

1. Check that the printer is correctly connected to the computer.

If the connection is through a network, print the printer’s configuration pages

(hold down the Power key while pressing the OK key four times), and check in

the TCP/IP section that the Status is shown as Ready. Make a note of the

printer’s IP address and subnet mask, which are in the same section.

• If the IP address is 0.0.0.0 or 192.0.0.192, refer to your printer’s setup

poster.

• If the Status is Ready, you can use a Web browser to check the network

connection between printer and computer. Simply type your printer’s IP

address into your browser, where you would normally type a URL. If you get

a reply from the printer, then the network connection between the printer

and the computer is working.

• If the Status is Not Ready, or if the printer does not reply to the Web

browser, check that the printer’s IP address and subnet mask belong to your

network.

• If necessary, consult your network administrator.

2. Check that the printer queue is not paused.

3. If you are using Mac OS X, make sure you selected “HP IP Printing” when you

created your printer, and not “IP Printing”.

QRG110plusnr.fm Page 15 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

16

The problem is… something else

The HP Designjet System Maintenance utility gives you access to support and

troubleshooting facilities on the Web, if you have an Internet connection. Even

without an Internet connection, it provides several facilities that may help to solve

printer problems.

To start HP Designjet System Maintenance under Windows:

1. From the Windows taskbar, select Start > Settings > Printers.

2. Right-click your printer’s icon and select Printing Preferences (Windows 2000

or XP), Document Defaults (Windows NT 4), or Properties (Windows 98 or

Me) from the pop-up menu.

3. Select the Advanced tab and click the Maintenance button.

To start HP Designjet System Maintenance under Mac OS, double-click the HP

Designjet System Maintenance icon on your desktop. Alternatively, under Mac OS

X you can select your printer in the Print Center and click Configure.

Under Windows or Mac OS, your Web browser should be started automatically

when you have followed the instructions above.

If you cannot follow these instructions successfully…

• …it may be that your computer does not manage the printer. In this case, use

HP Designjet System Maintenance from the printer server.

• …or it may be that the printer is managed by your computer but HP Designjet

System Maintenance has not been installed. In this case, install it from the HP

Designjet Software Setup CD.

For much more about

troubleshooting printer

problems, see the

section ‘The Problem

Is…’ on the

Using Your

Printer

CD.

QRG110plusnr.fm Page 16 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

17

Tell me about the front panel

The front panel (or control

panel) of the printer gives

information about the state

of the printer, and also has

three keys (or buttons) that

let you control the actions of

the printer.

The keys are:

• Power: Turns the power

on and off.

• Cancel: Cancels the

current operation.

• OK: Indicates to the printer:

• that you have now loaded paper in the appropriate tray or feed, and the

printer may start printing;

• that you have corrected a problem—for example, you have removed

jammed paper or replaced a failing printhead—and that the printer should

continue with its activity—for example, it should resume printing;

The lights are:

• Power: The Power (green) light is on when the printer is switched on.

• Attention: The Attention (yellow) light is on when the printer requires a user

action—for example, to close the top cover (if the display is blank).

The printer’s front panel has a Display area that gives information about the printer.

The sets of icons in the lower two-thirds of the display refer respectively to the Black,

Cyan, Magenta, and Yellow components of the ink system.

Display

Cancel key

OK key

Attention light

Power key

Power light

QRG110plusnr.fm Page 17 Wednesday, June 16, 2004 2:26 PM

HP Designjet 110plus/110 plus nr printer—

Quick Reference Guide

18

Press a Key: When flashing:

Printer waiting.

Action: Press the OK

key.

When off: Normal.

Paper jam: When flashing:

Paper jammed, paper

stalled or carriage

stalled.

Action: Clear the

paper jam.

See page 12.

When off: Normal.

The four icons shown here refer to the amount of ink in each of

the ink cartridges.

Use HP Designjet System Maintenance:

When flashing: Hardware error.

Action: Run the HP Designjet System Maintenance utility for the

printer (see page 16). Make sure that the printer is connected.

When off: Normal.

Tell me about the icons on the front panel

Busy: When flashing:

Printing, cancelling

job, drying, powering

off. The icon flickers if

the top or side cover is

open. Action: close the

top cover or close the

side cover.

When off: Printer is

powered off, idle, or

awaiting user action.

Paper When flashing:

misaligned: The paper is

misaligned and must

be reloaded to print.

Action: Reload the

paper.

When off: Normal.

State of When flashing:

Sheet Paper: Out of paper or

paper stalled.

Action: Add paper or

clear the paper path.

When off: Normal.

A flashing printhead icon (at the bottom) indicates a

problem with that printhead.

State of the When on:

roll: The roll is loaded.

When flashing: The

roll is empty or stuck.

Action: Load roll.

When off: There is no

roll loaded.

QRG110plusnr.fm Page 18 Wednesday, June 16, 2004 2:26 PM

La page charge ...

HP DesignJet 110plus Printer series Guide de référence

HP DesignJet 110plus Printer series Guide de référence

dans d''autres langues

Documents connexes

Autres documents