Philips SC2001/01 Manuel utilisateur

SC2001

4203.000.6357.3.indd 1 27-04-10 15:00

2

4203.000.6357.3.indd 2 27-04-10 15:00

3

A

B

D

C

E

F

G

H

I

J

K

L

O

M

N

1

4203.000.6357.3.indd 3 27-04-10 15:00

4

4203.000.6357.3.indd 4 27-04-10 15:00

SC2001

ENGLISH 6

DEUTSCH 28

ESPAÑOL 52

FRANÇAIS 75

ITALIANO 99

NEDERLANDS 123

PORTUGUÊS 146

4203.000.6357.3.indd 5 27-04-10 15:00

6

Table of contents

Introduction 6

Benets 7

Intense Pulsed Light (IPL) technology for home use 7

Effective hair re-growth prevention for everyday smoothness 7

Gentle treatment, even on sensitive body areas 7

Cordless operation for maximum freedom and exibility 7

Lamp does not require replacement 7

General description 7

Important 8

Danger 8

Warning 8

Caution 9

For whom is Philips Lumea not suitable? 9

Contraindications 10

How Philips’ Intense Pulsed Light technology works 11

Hair growth 11

Working principle 11

Charging 12

Preparing for use 12

Preparing treatment areas 12

Setting the light intensity 13

Recommended light intensities (1-5) 14

Tanning advice 14

Using the appliance 15

First use 15

Subsequent use 16

Guidelines for treatment 17

Average treatment time 17

Using the appliance on the legs 18

How to achieve optimal results 18

Possible side effects and skin reactions 19

After use 19

Cleaning and maintenance 19

Storage 20

Environment 21

Removing the rechargeable batteries 21

Guarantee and service 22

Replacement parts 22

Technical specications 22

Troubleshooting 23

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet

from the support that Philips offers, register your product at www.philips.

com/lumea.

Hair removal with light is one of the most effective methods to get

rid of unwanted body hair with longer-lasting results. It is completely

different from current home hair removal methods and Philips has been

investigating this method together with leading dermatologists for almost

10 years. You can now use this innovative technology comfortably in the

privacy of your own home, whenever and wherever you want.

ENGLISH

4203.000.6357.3.indd 6 27-04-10 15:00

This appliance has been designed and developed for use by women only

and is intended for removing body hair on areas mentioned below:

- underarms

- bikini area

- legs

Do not use the Philips Lumea IPL hair removal system on the face. Philips

Lumea is designed for use by one person only. Philips Lumea is not

designed for use by men.

For more information about Philips Lumea, see www.philips.com/lumea.

Check our homepage regularly for updates.

Benets

This appliance provides the following benets:

Intense Pulsed Light (IPL) technology for home use

Philips Lumea uses a light-based technology called ‘Intense Pulsed Light’

(IPL). IPL is also used in the professional beauty market for hair removal

and has been in use for the last fteen years. Philips Lumea now brings this

innovative technology to the comfort of your home.

Effective hair re-growth prevention for everyday smoothness

This method provides you with long-lasting hair regrowth prevention and

silky-smooth skin. Our studies have shown a signicant hair reduction

already after two treatments. Optimal results were generally achieved after

four to ve treatments. A reduction in hair density is visible from treatment

to treatment. How fast the effect becomes visible and how long the results

last varies from person to person. To treat all hairs successfully and prevent

the hair root from becoming active again, the treatments have to be

repeated once every two weeks for the rst two months. Your skin should

be smooth and hair-free by then. To ensure that you keep these results, we

advise you to repeat treatments on the underarms and bikini line every

two weeks. On the legs, regrowth is usually slower. Therefore, a treatment

once every four weeks is probably sufcient to keep your legs smooth

and hair-free. If you see too many hairs grow back within these four weeks,

simply shorten the interval between treatments again, but do not treat

more often than once every two weeks.

Gentle treatment, even on sensitive body areas

Philips Lumea has been developed in close cooperation with leading

dermatologists for an effective and gentle treatment, even on the most

sensitive body areas.

Cordless operation for maximum freedom and exibility

Because the appliance runs on rechargeable batteries, it is portable and can

be used anywhere.

Lamp does not require replacement

Philips Lumea has a lamp with a capacity of 40,000 ashes, which is enough

to last the product’s lifetime if used according to the instructions.

General description (Fig. 1)

A Light exit window with lter glass

B Removable window

C Metallic surface inside the removable window

D Safety system (safety ring with contact switches)

ENGLISH 7

4203.000.6357.3.indd 7 27-04-10 15:00

E Flash button

F Intensity lights (1- 5)

G % Intensity increase button

H ^ Intensity decrease button

I Charging light and battery low indication

J On/off button

K ’Ready to ash’ light

L Appliance socket

M Adapter

N Small plug

O Air vents

Also included: pouch and cleaning cloth

Important

Read this user manual carefully before you use the appliance and save it for

future reference.

Danger

- Water and electricity are a dangerous combination. Do not use

this appliance in wet surroundings (e.g. near a bath, a shower or a

swimming pool).

- Keep the appliance and the adapter dry.

Warning

- This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for

their safety.

- Children should be supervised to ensure that they do not play with the

appliance.

- The appliance is not intended for children younger than 14 years.

Teenagers aged between 15 and 18 years can use the appliance with

the consent and/or assistance of their parents or the persons who have

parental authority over them. Adults from 19 years and older can use

the appliance freely.

- Only charge the appliance with the adapter supplied.

- Do not use the appliance or the adapter if it is damaged.

- Do not use the appliance if the lter glass is broken.

- If the adapter is damaged, always have it replaced with one of the

original type in order to avoid a hazard.

- The adapter contains a transformer. Do not cut off the adapter to

replace it with another plug, as this causes a hazardous situation.

- To prevent damage:

- Never cover the ventilation slots during use.

ENGLISH8

4203.000.6357.3.indd 8 27-04-10 15:00

- Make sure nothing can obstruct the air ow through the ventilation

slots.

- Never subject the appliance to heavy shocks and do not shake or drop

it.

- If you take the appliance from a very cold environment to a very warm

environment, wait approximately 3 hours before you use it.

- Never use or store the appliance in a dusty environment.

- Never leave the appliance unattended when it is switched on. Always

switch off the appliance after use.

- Do not expose the appliance to direct sunlight or UV light for a longer

time.

- Do not ash against white, smooth or reective surfaces like paper,

mirrors, oors, walls etc. This can cause severe damage to the

removable window. Only ash when the appliance is in contact with

skin.

Caution

- Please use this appliance only at settings suitable for your skin type. Use

at higher settings than those recommended can increase the risk of

skin reactions and side effects.

- This appliance is only intended for removing women’s body hair

from areas below the neck. Do not use it for any other purpose. This

appliance is not designed for use by men.

- Keep the following things in mind to avoid compromising

the lifetime of Philips Lumea: Use by more than one

person and more frequent use than indicated in this user

manual can severely hamper the efcacy of the appliance

and can cause certain components to stop functioning.

- Do not expose the appliance to temperatures lower than 15°C or

higher than 35°C during use.

- The appliance is equipped with a built-in overheat protection. If the

appliance overheats, it does not ash. Do not switch off the appliance,

but let it cool down for approx. 15 minutes before you continue with

your treatment.

- Always return the appliance to a service centre authorised by Philips

for examination or repair. Repair by unqualied people could cause an

extremely hazardous situation for the user.

- Never use the appliance in any of the cases mentioned under

Contraindications.

For whom is Philips Lumea not suitable?

Philips Lumea is not designed for everyone. If any of the following is true

for you, then this appliance is not suitable for you to use!

- If your natural hair colour in the treatment areas is light blond, white,

grey or red.

- If you are of skin type VI (you rarely or never get sunburnt and you tan

very darkly). In this case you run a high risk of developing skin reactions

such as strong redness, burns or discolourations when you use Philips

Lumea.

- There are medications and health conditions that may lead to

adverse reactions when you use Philips Lumea. Please read section

‘Contraindications’ to determine whether any of these apply to you.

ENGLISH 9

4203.000.6357.3.indd 9 27-04-10 15:00

- All types of tanning can inuence the safety of the treatment. This

applies to exposure to natural sunlight as well as articial tanning

methods such as tanning lotions, tanning appliances etc. If you are

tanned or are planning to tan, please see chapter ‘Preparing for use’,

section ‘Tanning advice’.

Contraindications

Your skin may become a little red and irritated after you have used the

appliance. This phenomenon is absolutely normal and quickly disappears.

If the irritation does not disappear within three days, we advise you to

consult a doctor.

Never use the appliance:

- If you have an unsuitable skin and/or hair type (consult the skin/hair

colour table to determine whether this appliance is suitable for you).

- If you have a skin disease such as active skin cancer, if you have a history

of skin cancer or any other localised cancer in the areas to be treated.

- If you have pre-cancerous lesions or multiple atypical moles in the areas

to be treated.

- If you have a history of collagen disorder, including a history of keloid

scar formation or a history of poor wound healing.

- If you have a history of vascular disorder, such as the presence of

varicose veins or vascular ectasia in the areas to be treated.

- If your skin is sensitive to light and easily develops a rash or an allergic

reaction.

- If you have infections, eczema, burns, inammation of hair follicles,

open lacerations, abrasions, herpes simplex, wounds or lesions and

haematomas in the areas to be treated.

- If you have had surgery in the areas to be treated.

- If you have epilepsy with ashlight sensitivity.

- If you have diabetes, lupus erythematodes, porphyria or congestive

heart disease.

- If you have any bleeding disorder.

- If you have a history of immunosuppressive disease (including HIV

infection or AIDS).

- On areas of your skin where you are currently being treated with or

have recently been treated with Alpha-Hydroxy Acids (AHAs), Beta-

Hydroxy Acids (BHAs), topical isotretinoin and azelaic acid.

- If you have taken oral isotretinoin Accutane® or Roaccutane® in the

last six months.This treatment can make skin more susceptible to tears,

wounds and irritations.

- When you are on painkillers, which reduce skin’s sensitivity to heat.

- If you are taking photosensitising agents or medications, check the

package insert of your medicine and never use the appliance if it is

stated that it can cause photo-allergic reactions, photo-toxic reactions

or if you have to avoid sun when taking this medicine.

- If you take anticoagulation medications, including heavy use of aspirin, in

a manner which does not allow for a minimum 1-week washout period

prior to each treatment.

- If you take immunosuppressive medications.

- Over or near anything articial like silicon implants, Implanon

contraceptive implants, pacemakers, subcutaneous injection ports

(insulin dispenser) or piercings.

ENGLISH10

4203.000.6357.3.indd 10 27-04-10 15:00

- On moles, freckles, large veins, darker pigmented areas, scars, skin

anomalies without consulting your doctor. This can result in a burn

and change of colour, which makes it potentially harder to identify

skinrelated diseases (e.g. skin cancer).

- On nipples, areolas and mucous areas (inner vagina and anus).

- On warts, tattoos or permanent make-up. This can result in a burn and

change of colour.

- After intensive sunbathing and/or on sunburnt skin or if you use suntan

accelerators. See chapter ‘Preparing for use’, section ‘Tanning advice’ for

more information.

- If you use long-lasting deodorants. This can result in skin reactions. See

chapter ‘Using the appliance’, section ‘Possible side effects and skin

reactions’.

- If you are pregnant or breastfeeding.

How Philips’ Intense Pulsed Light technology works

Hair growth

Depending on age, metabolism and other factors, everyone’s hair grows

differently, but hair normally grows in three phases:

1 Anagen phase (growing phase)

The hair grows actively from the root. In this phase the concentration

of melanin is highest. Melanin is responsible for the pigmentation of the

hair. The more melanin there is in the root, the darker the hair is. Melanin

concentration is also the determining factor for the efcacy of this method.

Only hairs in the anagen phase are susceptible to treatment with light.

2 Catagen phase (degradation phase)

The hair growth stops and the root shrinks before the hair sheds.

3 Telogen phase (resting phase)

The old hair separates from the root and sheds. The root remains at rest

until the biological clock tells it to become active again and grow a new

hair. Hairs on an area of skin are usually in different stages of the cycle of

hair growth.

Working principle

The appliance works by heating up the hair and root beneath the skin.

The melanin in the hair and hair root absorbs the released light pulses. The

darker the colour of the hair, the more heat can be absorbed. This process

stimulates the hair to go into the resting phase.

The hair now sheds naturally and the hair growth is inhibited. Hairs can

take one or two weeks to shed. Optimal hair removal cannot be obtained

with a single session, since only hairs in the anagen phase are susceptible

to treatment with light. During a treatment, hairs on the treated area are

usually in different stages of the cycle of hair growth.

To treat all hairs successfully and prevent the hair root from becoming

active again, the treatments have to be repeated once every two weeks

for the rst two months. Your skin should be smooth and hair free by then.

To ensure that you keep these results, it is advised that you keep repeating

treatments every two weeks on the underarms and bikini line. On the legs,

however, regrowth of hair is usually slower. Therefore, a treatment once

every four weeks should also be sufcient to keep your legs smooth and

hair free. If too many hairs grow back in these four weeks, then simply

shorten the interval between treatments again, but do not treat more

often than once every two weeks.

1 2 3 4

ENGLISH 11

4203.000.6357.3.indd 11 27-04-10 15:00

An integrated optical lter makes sure no UV light reaches the skin and

therefore leaves it unharmed.

Electromagnetic elds (EMF)

This Philips appliance complies with all standards regarding electromagnetic

elds (EMF). If handled properly and according to the instructions in this

user manual, the appliance is safe to use based on scientic evidence

available today.

Charging

Fully charge the batteries before you use the appliance for the rst time

and when the batteries are empty. Fully charging the batteries takes up to

1.5 hours.

Charge the appliance when the charging light lights up orange during use to

indicate that the battery is low. When this happens, the remaining capacity

is at least 30 ashes.

Fully charged batteries provide at least 150 ashes at light intensity 5, which

amounts to approx. 15 minutes of cordless operation time.

Fully charge the appliance every 3 to 4 months, even if you do not use the

appliance for a longer time.

Charge the appliance in the following way:

1 Switch off the appliance.

2 Insert the small plug into the appliance and put the adapter in the

wall socket.

, The charging light ashes green to indicate that the appliance is

charging.

, When the batteries are fully charged, the charging light

lights up green continuously.

Notes:

- The adapter feels warm during charging. This is normal.

-

You cannot use the appliance during charging.

.

- This appliance is equipped with battery overheat protection and does

not charge if the room temperature exceeds 40°C.

Never cover the appliance and adapter during charging.

3 After charging, remove the adapter from the wall socket and pull the

small plug out of the appliance.

Preparing for use

For optimal results and highest efcacy, prepare the areas on which you

intend to use the appliance in the manner described below.

Preparing treatment areas

1 Shave the areas you intend to treat as long as you still experience

hair regrowth.

Note: If your last depilation method involved removing hairs by the roots (e.g

epilating, waxing etc.), wait until you notice signicant hair regrowth before

you use Philips Lumea . Make sure you shave the area before you use Philips

Lumea. Shaving is necessary to ensure that the light energy is channelled to

the hair root in the most efcient way.

ENGLISH12

4203.000.6357.3.indd 12 27-04-10 15:00

Please note that treatment on unshaved or improperly shaved

areas has a number of undesired effects:

- Contamination (burns/black spots) of the removable window with

stray hairs and dirt. A contaminated removable window can reduce the

lifetime and efcacy of the appliance. In addition, burns/black spots on

the removable window can cause the treatment to become painful or

cause skin reactions like redness and discolouration.

- Hairs on your skin can burn and this can result in an unpleasant smell.

2 Clean your skin and make sure it is hair-free, entirely dry and

free from oily substances (e.g. present in cosmetic products like

deodorants, lotions, perfumes, tanning creams and sunscreens).

3 Check the appliance, especially the removable window and lter glass

for trapped hair, dust and bres. If you see any contamination, clean

the appliance according to the instructions in chapter ‘Cleaning and

maintenance’.

Notes:

- If shaving causes wounds or lesions, your skin may be more sensitive

and the light treatment might feel uncomfortable sometimes.

- Once the hairs stop growing back - which usually happens after 4-5

treatments - you no longer have to shave before you use the appliance.

- If shaving causes skin irritation, you can also use a trimmer to trim the

hair as short as possible. Light treatment after trimming might make it

a little uncomfortable and you may get the smell of burning hair. Make

sure you always use a setting that is comfortable for you. Using the

appliance on trimmed hair might increase the chances of hairs getting

trapped in the recessed window. Make sure you clean the appliance

carefully after each treatment.

Setting the light intensity

Philips Lumea is an appliance developed for consumer use at home and

therefore NOT COMPARABLE with professional light-based appliances

with respect to pain sensation. Pulses of light delivered by Philips Lumea

are gentler than those from professional appliances and therefore you can

expect a convenient and effective treatment.

You have to adjust the light intensity to your skin and body hair colour and

to a level you nd comfortable.

The table with recommended light intensities below helps you to establish

the right light intensity.

1 Consult the table below to determine which light intensities are

most suitable for your skin and body hair colour and to check if this

method is suitable for you (if it is not, this is indicated with x in the

table).

Persons with darker skin run a higher risk of skin irritation because their

skin absorbs more light. Therefore lower intensities are recommended

for persons with darker skin.

2 For each body area you want to treat, select a suitable intensity

in the recommended range that is as high as possible but does

not cause any discomfort on the skin. Each body area and possibly

even parts of a body area may require a separate appropriate light

ENGLISH 13

4203.000.6357.3.indd 13 27-04-10 15:00

intensity. Therefore you should lower the light intensity if you

experience any discomfort anywhere.

The light intensity you use can feel warm or hot on the skin, but should

never feel uncomfortable. To prevent skin reactions, see chapter ‘Using

the appliance’, section ‘Possible side effects and skin reactions’.

Recommended light intensities (1-5)

In the table below, ‘x’means that the appliance is not suitable for you.

Skin colour &

characteristics:

White

(always

sunburn,

no

tanning)

Beige

(easy

sunburn,

minimal

tanning)

Light

brown

(sometimes

sunburn,

good

tanning)

Mid brown

(rarely

sunburn,

fast and

good

tanning)

Dark

brown

(rarely

sunburn,

very good

tanning)

Black

(rarely

to never

sunburn,

very dark

tanning)

hair colour: dark

blond/light brown/

brown/dark brown/

black

4/5 4/5 3/4/5 3/4 1/2/3 x

hair colour: white/

grey/red/light blond

x x x x x x

Important:

- To check whether Philips Lumea is suitable for you, see section ‘For

whom is Philips Lumea not suitable?’.

- At higher light intensities:

- the method is more effective.

- you have a higher risk of skin reactions. See chapter ‘Using the

appliance’, section ‘Side effects and skin reactions’.

- the pain sensation can be stronger.

- If your skin has been exposed to natural sunlight or an articial tanning

method, your skin may be darker than during the previous treatment.

Perform a skin test (see chapter ‘Using the appliance’, section ‘First use’)

on the area to be treated to determine if you have to use a lower light

intensity than usual. For more information, see section ‘Tanning advice’

below.

Tanning advice

Sun exposure before treatment

- Wait at least 48 hours after sunbathing before you use the appliance.

Sunbathing can cause skin to darken (tan) and/or can cause sunburn

(reddening of the skin).

- After these 48 hours, check the skin for any remaining sunburn. Do not

use Philips Lumea as long as sunburn persists.

- When the sunburn has disappeared, perform a skin test (see chapter

‘Using the appliance’, section ‘First use’) on the area to be treated to

determine the appropriate light intensity.

- If your skin is tanned, you run a very high risk of developing skin

reactions after treatment with Philips Lumea. Perform a skin test (see

chapter ‘Using the appliance’, section ‘First use’) on the area to be

treated to determine the appropriate light intensity.

Sun exposure after treatment

ENGLISH14

4203.000.6357.3.indd 14 27-04-10 15:00

- Wait at least 24 hours after treatment before you expose treated

areas to the sun. Even after 24 hours, make sure that the treated skin

does not show any redness from the treatment anymore before you

expose it to the sun.

- Cover treated areas when you go out in the sun or use a non-

perfumed sun block in the two weeks after the treatment.

- Exposing treated areas to the sun immediately after treatment without

protection can increase the risk of adverse side effects and skin

reactions. See chapter ‘Using the appliance’, section ‘Possible side effects

and skin reactions’.

Tanning with articial light

- Follow the instructions in ‘Sun exposure before treatment’ and ‘Sun

exposure after treatment’ above.

Tanning with creams

- If you have used articial tanning lotion, wait until the articial tan has

fully disappeared before you use Philips Lumea.

Note: For more details on unwanted skin reactions, see chapter ‘Using the

appliance’, section ‘Possible side effects and skin reactions’.

Using the appliance

Shave the area you intend to treat before you use the appliance (see

chapter ‘Preparing for use’).

If the treatment becomes intolerably painful at any point in time, reduce

the light intensity setting until the treatment is comfortable again. If you

notice skin reactions stronger than slight redness, stop the treatment

immediately and read section ‘Possible side effects and skin reactions’ in

this chapter.

First use

When you use the appliance for the rst time, we advise you to perform

a skin test on the area to be treated to check your skin’s reaction to the

treatment and to get accustomed to light-based treatment.

1 Choose an area close to the intended treatment area.

2 Press the on/off button to switch on the appliance.

, Intensity light 1 goes on automatically to indicate that the appliance

is switched on at default intensity 1.

3 Apply one ash at the lowest recommended intensity for your skin

type.

4 As long as it feels comfortable (not painful), increase the setting by

one level within the recommended range for your skin type and

apply one ash for each setting. Do not apply more than one ash on

the same spot.

ENGLISH 15

4203.000.6357.3.indd 15 27-04-10 15:00

5 After the skin test, wait for 24 hours and check your skin for

any reaction. If the skin shows reactions, choose the highest setting

that did not result in any skin reaction for subsequent use.

Subsequent use

1 Before every treatment, clean the removable window, lter glass and

metallic surface of Philips Lumea.

2 Press the on/off button to switch on the appliance.

, Intensity light 1 goes on automatically to indicate that the appliance

is switched on at default intensity 1.

Note: It is normal that the appliance becomes warm during use.

3 Start each treatment by selecting the light intensity very carefully,

based on your skin’s sensitivity and comfort at that moment.

Your skin may react differently on different days/occasions for a number of

reasons. See section ‘Possible side effects and skin reactions’ in this chapter

for more information.

4 Press the % button to increase the intensity. To lower the intensity,

press the ^ button.

, Every time you press the button, the corresponding intensity

light starts to ash. This takes a few seconds.

5 Place the appliance perpendicularly on the skin so that the

removable window and the safety ring are in contact with the skin.

ENGLISH16

4203.000.6357.3.indd 16 27-04-10 15:00

6 Press the safety ring fully onto the skin with slight pressure.

Note: The safety ring has contact switches that together are the safety system

of the appliance. This safety ring prevents unintentional ashing without skin

contact.

, When all contact switches of the safety ring have been pushed

into the appliance, the ‘ready to ash’ light on the back of the

appliance goes on. This may take up to 5 seconds. When the ‘ready to

ash’ light is on, the appliance is ready to release a ash.

Tip: For easier use, stretch the skin you want to treat. On areas with softer skin,

you may need to exert more pressure on the appliance to push in all contact

switches.

Note: Bony areas like shinbone and ankles are more sensitive than other areas

of the body. When you press the window hard onto these areas, the skin can

be more susceptible to skin reaction like irritation and redness. See section

‘Possible side effects and skin reactions’ in this chapter. Press the window onto

the skin just hard enough to make the ‘ready to ash’ light go on, but no harder.

7 Press the ash button to release a ash. After the appliance has

ashed once, release the ash button.

Note: The visible light produced by the appliance is the reection of the ash

on the skin and is harmless to your eyes. It is not necessary to wear goggles

during use.

Note: Avoid looking straight into the light that comes out of the window when

the appliance is switched on.

8 For the next ash, repeat steps 5, 6 and 7. After each ash it takes 3

to 5 seconds until the appliance is ready to ash again.

Never ash the same area twice without lifting the appliance off the skin.

This prevents excessive heating and possible burning of the skin.

9 To avoid untreated areas, always make sure there is some overlap

with the previously treated area when you place the appliance on the

skin.The effective light only comes out of the light exit window. Make

sure the ashes are produced close to each other.

10 Switch off the appliance after you have nished the treatment.

11 Check the removable window and lter glass for hairs and dirt and

clean the appliance after use. See chapter ‘Cleaning and maintenance’.

ENGLISH 17

4203.000.6357.3.indd 17 27-04-10 15:00

Guidelines for treatment

Average treatment time

Area Approx. treatment time

Underarms 2 minutes per underarm

Bikini line 2 minutes per side

Entire bikini area 8 minutes

One lower leg 15 minutes

One full leg 30 minutes

Note: The average treatment times above have been observed during research

and tests. Individual treatment times may vary from person to person.

Note: Fully charged batteries offer at least 150 ashes at intensity 5, which

amounts to an operating time of approx. 15 minutes.

Using the appliance on the legs

If you use the appliance to treat your legs, you may have to recharge the

appliance during the treatment. This is normal. How long you can use the

appliance depends on the size of the treatment area and the intensity

setting used.

Tip: Many users combine leg treatments with other activities around the house

such as watching TV or listening to music. You can also try this to make the

experience more enjoyable and relaxing.

How to achieve optimal results

- Optimal results cannot be obtained with one single session. To remove

all hairs successfully and prevent the hair root from becoming active

again, the treatments have to be repeated once every two weeks for

the rst two months. Your skin should be smooth and hair-free by then.

- To ensure that you keep these results, we advise you to repeat the

treatments on the underarms and bikini line every two weeks. On the

legs regrowth is usually slower. Therefore, treatment of the legs once

every four weeks is probably sufcient to keep your legs smooth and

hair-free. If too many hairs grow back within these four weeks, simply

shorten the interval between treatments again, but do not treat more

often than once every two weeks. It is recommended to adhere

to this frequency for optimum results. When you use the appliance

more frequently than recommended, you also increase the risk of skin

reactions. See section ‘Possible side effects and skin reactions’ in this

chapter.

- Avoid treating exactly the same area multiple times during one session

as this does not improve the effectiveness of the appliance. However,

this does increase the risk of skin reactions.

- Never ash the same area twice without lifting the appliance off the

skin. This prevents excessive heating and possible burning of the skin.

- It is normal that hairs are still visible after the rst few treatments. See

chapter ‘Important’, section ‘How photo-epilation works’ for more

information.

ENGLISH18

4203.000.6357.3.indd 18 27-04-10 15:00

- Some hairs grow back even though you use the appliance frequently.

This happens because hairs are in different stages of the cycle of hair

growth during treatment. The hairs that grow back tend to be softer

and thinner.

Possible side effects and skin reactions

- Your skin shows slight redness and/or prickles, tingles or feels warm.

This phenomenon is absolutely harmless and disappears quickly.

- A skin reaction similar to sunburn may occur on the treated area for a

short while. If this does not disappear within 3 days, we advise you to

consult a doctor.

- Dry skin and itching may occur because of the combination of shaving

and light treatment. This is harmless and disappears within a few days.

You can cool the area with an ice pack or a wet facecloth. If dryness

persists, you can apply a non-scented moisturiser on the treated area

24 hours after the treatment.

- Burns, excessive redness and swelling: these reactions occur very rarely.

They are the result of using a light intensity that is too high for your

skin colour. If these reactions do not disappear within 3 days, we advise

you to consult a doctor. Wait with the next treatment until the skin has

healed completely and make sure you use a lower light intensity.

- Skin discolouration: this occurs very rarely. Skin discolouration manifests

itself as either a darker or lighter patch than the surrounding area.

This is the result of using a light intensity that is too high for your skin

colour. If the discolouration does not disappear within 2 weeks, we

advise you to consult a doctor. Do not treat discoloured areas until the

discolouration has disappeared and your skin has regained its normal

skin colour.

- Skin infection and inammation: This occurs very rarely and may be

caused by using the appliance on wounds or cuts that resulted from

shaving, on already existing wounds or on ingrown hairs.

- Excessive pain: this can occur during or after treatment if you have

used the appliance on unshaved skin, if you use the appliance at a light

intensity that is too high for your skin colour, if you ash the same

area more than once and if you use the appliance on open wounds,

inammations, infections, tattoos, burns, etc. See chapter ‘Important’,

section ‘Contraindications’ for more information.

After use

- Do not apply any cosmetic substances to the treated areas immediately

after treatment.

- Do not use deodorant after the treatment until any redness has

disappeared completely.

- See chapter ‘Preparing for use’, section ‘Tanning advice’ for information

about sun exposure and articial tanning.

Cleaning and maintenance

To ensure optimal results and a long life for the appliance, clean the

appliance before and after each use and, if necessary, also during the

treatment. The appliance loses its effectiveness if you do not clean it

properly.

ENGLISH 19

4203.000.6357.3.indd 19 27-04-10 15:00

Never clean the appliance or any of its parts under the tap or in the

dishwasher.

Never use scouring pads, abrasive cleaning agents or aggressive liquids

such as petrol or acetone to clean the appliance.

Never scratch the lter glass or the metallic surface inside the

removable window.

Note: Make sure that the contact switches of the safety ring do not get

jammed with dirt.

Note: Stop using the appliance when it is no longer possible to clean the lter

glass or the removable window.

1 Switch off the appliance, unplug it and let it cool down.

Note: The lter glass becomes hot during use. Make sure it has cooled down

before you clean it.

2 To remove the removable window, put your ngers in the recesses

at the top and bottom and pull gently. The window should come off

easily.

3 Moisten the soft cloth supplied with the appliance with a few drops

of water and use it to clean the following parts:

- the surface of the lter glass

- the outside surface of the removable window

- the metallic frame inside the removable window

Note: If water does not clean effectively, use a few drops of 70% isopropyl

alcohol to clean the parts mentioned above.

Note: A contaminated recessed window can look like this picture. Make sure

you clean the appliance before and after each use and, if necessary, also

during the treatment according to the instructions in this section.

4 If necessary, clean the outside of the appliance with the dry soft cloth

supplied with the appliance.

Storage

1 Switch off the appliance, unplug it and let it cool down.

2 Clean the appliance before you store it.

3 Put the appliance in the pouch supplied.

4 Store the appliance in a dry place at a temperature between 0°C and

60°C.

ENGLISH20

4203.000.6357.3.indd 20 27-04-10 15:00

La page charge ...

Philips SC2001/01 Manuel utilisateur

Philips SC2001/01 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents