wattstopper LMNC-ENC1 Guide d'installation
- Taper
- Guide d'installation
Wattstopper
®
DLM Network Enclosure
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
No: 28703 – 7/19 rev. 1
Catalog Number • Numéro de Catalogue • Número de Catálogo: LMNC-ENC1
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
DESCRIPTION
The LMNC-ENC1 assembly provides protection and conduit connection points for the
LMJA-8125 or LMJA-8300 and an integral 120VAC/15A receptacle. It is designed for
applications where code or the local AHJ requires that low voltage wiring such as DLM Local
Network cables, control and communication wiring be run inside conduit.
ATTENTION: This enclosure is provided with an earthing conductor. Proper grounding of
this enclosure shall be in accordance with all applicable regulations, local and NEC codes.
For complete installation, wiring, and operation of the LMJA-8125 or LMJA-8300 , see the
instructions provided with the unit.
REMOVE ENCLOSURE COVER REMOVE RECEPTACLES REMOVE RECEPTACLE BOX
MOUNT THE ENCLOSURE
Position and mount the box so that the cover is not obstructed
for removal and access.
ATTACH GROUND WIRES
Attach the ground wire coming from the conduit, and a second
ground wire going to the receptacle from the grounding boss.
Slide cover
back and up
Remove
receptacles
Remove
receptacle
plate
Remove screw
Slide receptacle
box to the unlock
position
Lift up to
remove
Punch out one of the knockout
holes located behind the
receptacle box, on the top or
side, for line voltage wiring
Line voltage in these
two knockouts only
Mount the enclosure
using 4 mounting screws
(not provided)
Additional knockout
holes are available for
low voltage wiring
Attach conduit
Ground screws
Supply ground wire
Loosen
screws (4)
(do not remove)
1 2
3
4
5
6
7
8
9
J
K
L
WARNING: TURN THE POWER OFF AT THE
CIRCUIT BREAKER BEFORE WIRING.
800.879.8585
www.legrand.us/wattstopper
No.28703 – 7/19 rev. 1
© Copyright 2019 Legrand All Rights Reserved.
© Copyright 2019 Tous droits réservés Legrand.
© Copyright 2019 Legrand Todos los derechos reservados.
Wattstopper warranties its products to be free
of defects in materials and workmanship for a
period of five (5) years. There are no obligations
or liabilities on the part of Wattstopper for
consequential damages arising out of, or in
connection with, the use or performance of this
product or other indirect damages with respect
to loss of property, revenue or profit, or cost of
removal, installation or reinstallation.
Wattstopper garantit que ses produits sont
exempts de défauts de matériaux et de fabrication
pour une période de cinq (5) ans. Wattstopper
ne peut être tenu responsable de tout dommage
consécutif causé par ou lié à l’utilisation ou
à la performance de ce produit ou tout autre
dommage indirect lié à la perte de propriété, de
revenus, ou de profits, ou aux coûts d’enlèvement,
d’installation ou de réinstallation.
Wattstopper garantiza que sus productos
están libres de defectos en materiales y mano
de obra por un período de cinco (5) años. No
existen obligaciones ni responsabilidades por
parte de Wattstopper por daños consecuentes
que se deriven o estén relacionados con el
uso o el rendimiento de este producto u otros
daños indirectos con respecto a la pérdida
de propiedad, renta o ganancias, o al costo
de extracción, instalación o reinstalación.
WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA
REPLACE RECEPTACLE BOX WIRE RECEPTACLE
ATTACH POWER CABLE AND GROUND WIRE
TO THE SEGMENT MANAGER
REPLACE ENCLOSURE COVER
INSTALL THE LMJA-8125 OR LMJA-8300
Tighten screw.
Pull the wires through
the receptacle box. Slide
the receptacle box into
the locked position.
Hang the hooks on the
back of the LMJA over
the top of the DIN rail.
Using a screwdriver, pull the
lever down while pushing
the LMJA against the
enclosure until you hear it
snap into place.
LMJA-8125 or
LMJA-8300
Push up on the lever a short
distance until you hear a small
snap. This locks the LMJA to
the DIN rail.
DIN rail
Attach the ground wire from
the LMJA to the grounding
boss on the enclosure.
Attach the power cable from the LMJA
to the receptacle in the enclosure.
Place cover over screws
and slide down.
Tighten screws (4).
M
N
O
P
Q R S
T
21
22
23
Wire the
receptacles.
Replace the receptacles
and the receptacle cover.
-
1
-
2
