DAK SF 3CT and DAK SF 3C • Setup Guide
This setup guide contains installation information about the DAK SF 3CT and DAK SF 3C Driver Assembly Kits. When assembled
to the BCK SF 3CT LP or BCK SF 3C LP back cans they become a fully functioning SF 3CT LP or SF 3C LP Soundeld XD full
range speaker, respectively. These speakers can be installed by a single trade installation procedure or by a multitrade installation
procedure (see the SF 3C LP and SF 3CT LP User Guide, available at www.extron.com, for details). The entire assembly is
plenum rated.
WARNING: Potential risk of severe injury. Installation and service must be performed by authorized personnel only.
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. L’installation et l’entretien doivent être effectués
par le personnel autorisé uniquement.
NOTE: Installation of conduit and conduit adapters must conform to all applicable building codes and local ordinances.
1. Attach the speaker assembly to the back can enclosure.
a. Connect the speaker wires from the back can enclosure to the speaker assembly.
8
W
16W
100 V
70 V
4
W
2
W
4W
2W
1W
8W
8
Ω
8
Ω
16W
b. Rotate the speaker assembly so that the white arrows on the back can enclosure and the speaker assembly are aligned
with each other, and insert the speaker into the back can.
c. Using a at head screwdriver, tighten the three screws that attach the speaker assembly to the back can.
8
W
16
W
100 V
70 V
4
W
2
W
4W
2W
1W
8W
8Ω
8
Ω
16
W
8W
16W
100 V
4W
2W
8Ω
8Ω
1
DAK SF 3CT and DAK SF 3C • Setup Guide (Continued)
© 2019 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
2
ATTENTION:
• To avoid damaging the speaker, do not overtighten the three locking arm screws.
• Pour éviter d’endommager l’enceinte, ne serrez pas trop les quatre vis.
2. For the SF 3CT LP, set the rotary tap selector switch to the appropriate setting using a small screwdriver.
ATTENTION:
• When setting the taps for a distributed (high impedance) system, do not tap the system above the rated
power of the amplifier.
• Lors de la mise en place des capteurs pour un système distribué (haute impédance), n’exploitez pas le
système au delà du niveau d’alimentation de l’amplificateur.
• When connecting multiple speakers in 8-ohm mode, be sure that the combined rated impedance does not
equal a value less than the minimum rated impedance of the amplifier.
• Lors de la connexion de plusieurs enceintes en mode 8ohm, assurez vous que le niveau d’impédance
combinée ne soit pas équivalent à une valeur inférieure à l’impédance minimum de l’amplificateur.
8
W
16
W
1
00 V
70 V
4
W
2
W
4W
2W
1W
8W
8Ω
8
Ω
16W
Adjust the Tap Selector
8W
16W
100 V
70 V
4W
2W
4W
2W
1W
8W
8Ω
8Ω
16W
3. Install the grille. Position the grille so that it covers the bafe of the speaker. Six small magnets secure the grille in place.
Speaker Grille
8
W
16
W
1
00 V
70 V
4
W
2
W
4W
2W
1
W
8W
8Ω
8
Ω
16W
68-2224-52 Rev A 02 19
-
1
-
2
Extron SF 3CT LP Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Extron SF 3CT LP User manual
Documents connexes
-
Extron SF 3CT LP Manuel utilisateur
-
-
Extron SF 26CT LP Manuel utilisateur
-
Extron DAK SF 26CT Manuel utilisateur
-
-
-
-
-
-