QSC SC-443 Manuel utilisateur

Marque: QSC

Modèle: SC-443

Taper: Manuel utilisateur

Developed specifically for the unique requirements

of professional motion picture playback, the SC-443

extends QSC’s commitment to the cinema market. As

a member of the DCS Digital Cinema Speaker Series,

the SC-443 is a three-way, selectable bi or tri-amplified

screen channel loudspeaker system comprised of

three main units—the MH-1075 high-frequency system

and dual LF-4215 low-frequency systems.

The MH-1075 mid-high system features a high

output, horn loaded 10" midrange cone driver and a

3" (75mm) titanium diaphragm compression driver

mounted to an adjustable pan and tilt bracket. The

MH-1075 includes a driver protection network and

a passive crossover for bi-amp operation. Power

limiter circuitry protects the high-frequency driver

from overpowering. The MH-1075 provides extended

frequency coverage for the critical midrange band. A

high power 10" cone driver allows operation as low

as 250 Hz and the advanced phase plug coupling

permits a crossover point of up to 1800 Hz to the

high-frequency horn. This ensures that most of the

dialog range is reproduced by a single element, for

unmatched intelligibility.

The LF-4215 dual 15" (381mm) low-frequency

enclosures are designed specifically to address the

extended low-frequency response required for cinema

applications. The dual LF-4215s cover the frequency

range from 35 Hz to 250 Hz. Close Coupled Woofers

(CCW), with their tight spacing between woofers,

improves coupling and keeps coverage angles wide

over a greater frequency range than more widely

spaced designs.

The SC-443 is designed for ease of installation.

The MH-1075 components come pre-assembled to

reduce field assembly time. Three bolts are all that

are required to secure the MH-1075 to the top of the

LF-4215 enclosure.

SC-443

Cinema Loudspeaker System

Specifications SC-443

Nominal Coverage 90° horizontal x +20 to -30° vertical

Frequency Range 32 Hz - 16 kHz (-6 dB)

Crossover Frequency 250 and 1700 Hz, 24 dB per octave

(2) LF-4215 MH-1075

Impedance 4

Ω each 8Ω

Sensitivity 1 watt /1 meter, 102.5 dB Bi-amp Tri-amp

half space 106 dB MF 105 dB HF 107.5 dB

Maximum Input Power

8 hours of 6 db crest factor 800 W RMS each 250 W RMS

275 W RMS 80 W RMS

IEC 268 noise spectrum

2 hours of 6 db crest factor 1000 W RMS each 350 W RMS

pink noise, 50 Hz - 20 kHz,

AES method

Recommended Amplifier Power 1600 W RMS maximum each 800 W RMS maximum

Recommended Processing Subsonic filter below 30 Hz, 4th order LR crossover at 200 and

> 18 dB per octave 1700 Hz via QSC DCM or QSControl.net

Connectors Barrier strip screw terminals Barrier strip screw terminals

accept up to #10 AWG stranded accept up to #10 AWG stranded wire

wire, four terminals; two inputs

and two parallel outputs

Transducers Four 15" (381mm) high efficiency, 10" high efficiency mid range,

extended bass woofer featuring 1.5" (38mm) exit, 2.5" titanium

4" copper voice coils diaphragm compression driver

Enclosure Quasi B4 alignment, ported Tilt/Pan Bracket

enclosure with fully flared ports, ±10° vertical tilt

symmetrical port design, tuned to ±10° horizontal pan

36 Hz, constructed of MDF and

heavily braced. Features vandal

resistant woofer mounting bolts

Dimensions (HWD) 72" x 30" x 20.3" 39" x 30" x 20"

(1820 mm x 762 mm x 516 mm) (990 mm x 762 mm x 508 mm)

Weight - Net 344 lbs (156 kg) 85 lbs (39 kg)

System Weight 429 lbs (195 kg)

Baffle Cut-Out 111.6" x 32"

1) Maximum input power tested in accordance with IEC 268-5 recommendations, 50 Hz - 20 kHz band limiting, 6 dB signal crest factor.

2) Maximum input power tested in accordance with IEC 268-5 recommendations, 200 Hz - 2 kHz band limiting, 6 dB signal crest factor.

passive

mid-high

Features

• Three-way selectable, bi or tri- amplified screen channel system

• MH-1075 provides 90° horizontal by +20° to -30° vertical coverage

• LF-4215 is constructed of MDF and features single woofer chambers

• Low-distortion waveguides provide highly articulate dialogue

• Shallow depth (20

") facilitates installation

• THX

™ approved for professional cinema applications

THX is a trademark of THX Ltd.

SC-443

Dimensions

qscaudio.com

Specifications subject to change without notice.

1675 MacArthur Boulevard • Costa Mesa, CA 92626 • Ph: 800/854-4079 or 714/957-7100 • Fax: 714/754-6174

SC-443 Spec Sheet - 02/22/06

Top

Side

21.7"

551 mm

20.3"

516 mm

30"

762 mm

Front

111"

2810 mm

36"

910 mm

39"

990 mm

72"

1820 mm

102 mm

18.9"

480 mm

*TD-000180-00*

Cinema Mid-High Loudspeaker System User Manual

MH-1063 10” (254mm) mid, 2.5” (63mm) compression driver

MH-1075 10” (254mm) mid, 3.0” (75mm) compression driver

Introduction

The MH-1063 and MH-1075 “mid-high packs” provide the mid and high frequency

components of three-way screen channel loudspeaker systems for high performance

cinema applications. They were designed to operate with and be directly mounted on

QSC’s cinema low frequency enclosures.

Mid frequencies are reproduced with a 10” (254mm) high-efficiency, phase-ring

loaded driver mounted on a custom designed cinema horn. The high-frequency driver

is a large format, 2.5” (63mm, MH-1063) or 3.0” (75mm, MH-1075) titanium dia-

phragm compression driver mounted on a custom high-frequency cinema horn. The

high frequency horn is a low-distortion waveguide providing highly articulate dialogue

without coloration associated with conventional horn loudspeakers. Both horns fea-

ture broad horizontal and vertical coverage angles to ensure coverage of every seat in

the auditorium. The driver assemblies are mounted on an adjustable pan and tilt

bracket that has an integral aiming sight, simplifying installation.

The MH-1063 and MH-1075 loudspeakers include a driver protection and crossover

network to assure reliable operation. DC blocking capacitors protect against DC or

low-frequency signals that could damage an unprotected driver. Power limiter circuitry

protects the driver from over-powering and an 18dB/octave crossover seamlessly

blends the high and mid frequency elements. Outboard processing is required to form

the crossover between the LF and MH loudspeakers.

Bi-amp or tri-amp operation is possible using a selector switch mounted on the con-

nections panel. The bi-amp setting provides a passive crossover network between mid

and high drivers. Separate amplifiers and an active crossover are required for the low

frequency channel and the mid-high channel. Tri-amp setting disables the internal

mid-high crossover and each driver is driven independently by its own amplifier and

active crossover; one for the low, one for the mid, and one for the high frequencies.

The MH-1063 and MH-1075 components come pre-assembled to reduce field assem-

bly time. Three bolts are all that are required to secure the mid-high assembly to the

top of a QSC low frequency enclosure.

Install in accordance with QSC Audio Product’s instructions and a

licensed, professional engineer. Only use attachments, mounts,

accessories, or brackets specified by QSC Audio Products, Inc. Refer

all servicing to qualified personnel. Servicing is required when the

apparatus has been damaged in any way.

WARNING! Before placing, installing, rigging, or suspending any

speaker product, inspect all hardware, suspension, cabinets, trans-

ducers, brackets and associated equipment for damage. Any missing,

corroded, deformed or non-load rated component could significantly

reduce the strength of the installation, placement, or array. Any such

condition severely reduces the safety of the installation and should

be immediately corrected. Use only hardware which is rated for the

loading conditions of the installation and any possible short-term

unexpected overloading. Never exceed the rating of the hardware or

equipment. Consult a licensed, professional engineer when any

doubt or questions arise regarding a physical equipment installation.

TD-000180-00 rev.A

QSC® is a registered trademark of QSC Audio Products, Inc.

“QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office

1675 MacArthur Blvd., Costa Mesa, CA, 92626 USA

Main Number (714) 754-6175 Sales & Marketing (714) 957-7100 or toll free (USA only) (800) 854-4079

Customer Service(714) 957-7150 or toll free (USA only) (800) 772-2834

Settings

BI-AMP / TRI-AMP Operating Mode Selection

Set the operating mode selector switch to BI-AMP or TRI-AMP, depending on your application setup.

Mounting

Attaching to Low Frequency Enclosure

The mid-high loudspeaker assembly attaches to the top of the QSC low frequency cabinet with three 5/16-18 bolts, 0.75” long, with

lock washers. This hardware ships installed on the low frequency cabinet. We recommend the use of serviceable thread locking com-

pound when installing the bolts to prevent loosening due to vibration. Do not fully tighten the mounting hardware before aiming (see

below).

Aiming

Aim the horn in the horizontal plane (pan) before tightening the attachment hardware. Adjust the vertical tilt with the mid-high vertical

adjustment bracket. The mid-high assembly is equipped with an aiming sight to assist in achieving desired coverage quickly and easily.

For typical applications, the aim point should be the center seat in the back row of the auditorium. If the cinema screen has already

been installed, a flashlight placed at the desired aiming point can be seen through the screen perforations in a darkened auditorium.

Where the sight holes are located:

How to use the sights:

Aim point:

BI-AMP-When set to BI-AMP, the MH-1063 and MH-1075 accepts mid-

high frequency signals on one set of inputs and uses an internal crossover

network between the mid- and high-frequency drivers. The signal applied

to the mid-high loudspeaker assembly must not contain low-frequency

content (below 200 Hz).

TRI-AMP- When set to TRI-AMP, the MH-1063 and MH-1075 accepts

separate mid- and high-frequency signals on two sets of inputs. The inter-

nal crossover network is bypassed and only the protective circuitry for the

H.F. driver remains. Each of the driver’s signals must have the appropriate

signal processing before operating.

Do not connect amplifiers directly to the driver inputs!

Always use the input terminal strip.

Connections

INPUT Terminals

The MH-1063 and MH-1075 have barrier strip screw terminals that accept up to #10 AWG (5.3mm

) stranded loudspeaker wire.

Observe proper polarity. Use the largest wire size and shortest wire length for the application.

OUTPUT Terminals

The OUTPUT terminals are factory-connected to the drivers. These terminals should ONLY be connected to their respective driver. Do

not connect signals to these terminals as all protection and equalization circuitry will be bypassed.

NOTE! Maintain proper loudspeaker connection polarity throughout the entire system for maximum performance.

Do not apply full range signal to the MH-1063 / MH-1075! There is a mid-high passive crossover for bi-amp mode

only. There is no crossover connected when operating in tri-amp mode. A protection network is always active. All

required signal processing must be done before the signal is applied to the loudspeaker. Do not connect any sig-

nal to the upper sets of OUTPUT terminals.

BI-AMP mode connections- Ensure the mode switch is set to BI-AMP, connect the input to the MH-1063 / MH-1075 to the lower

set of input terminals marked “BI-AMP + -”.

BI-AMP Mode- one

amplifier channel is used

for the low frequency

cabinet and one amplifier

channel for the mid-high

assembly. The MH-1063 /

MH-1075 mode switch is

set to BI-AMP. Active

crossovers are used

before amplification. The

mid-high assembly pro-

vides a passive crossover

between the mid and

high frequency drivers.

Connections (continued)

TRI-AMP mode connections- When the mode switch is set to TRI-AMP, connect the high frequency signal to the terminals marked

“INPUT HI + -” and the mid frequency signal to the terminals marked “INPUT MID + -”.

TRI-AMP Mode- one

amplifier channel is

used for the low fre-

quency cabinet, one

amplifier channel for

the mids, and one

amplifier channel for

the high frequencies.

The MH-1063 / MH-

1075 mode switch is

set to TRI-AMP,

bypassing the internal

mid-high passive cross-

over. Active or passive

crossovers are used

before amplification.

Power limiter and DC

blocking remain active.

MH-1063 Specifications (subject to change without notice)

Freq. Range 180 - 15k (-6dB, full space)

Nominal Coverage 90° horizontal X +20 to -30° vertical (50° total, adjustable mount provides for vertical plane adjustments.

The horizontal plane can be adjusted by altering mounting position on the low frequency enclosure before

tightening bolts.

DI: 9 dB (400 to 16k Hertz average)

Q: 8 (400 to 16k Hertz average)

Max. Output: [Tri-amp mode] Mid Freq. 135.5 dB SPL calculated peak, 1m, full space

[Tri-amp mode] High Freq. 131.5 dB SPL calculated peak, 1m, full space

[Bi-amp mode] 135 dB SPL calculated peak, 1m ,full space

Impedance: [Bi-amp mode] 8 ohms nominal

7.9 ohms minimum at 1500 Hertz

91 ohms maximum at 150 Hertz

Maximum Input Power [Tri-amp mode] Mid Freq. 275 W (AES method, 2 hrs.)

[Tri-amp mode] High Freq. 60 W (AES method, 2 hrs.)

[Bi-amp mode] 250 W (IEC method, 8 hrs.)

Sensitivity [Tri-amp mode] Mid Freq. 105 dB SPL, 1 watt, 1 meter

[Tri-amp mode] High Freq. 107.5 dB SPL, 1 watt, 1 meter

[Bi-amp mode] 135 dB SPL, 1 watt, 1 meter

Crossover Frequency [Tri-amp mode] 250 Hertz or higher, 24dB/octave and 1.7k Hertz, 24dB/octave

[Bi-amp mode] 250 Hertz or higher, 24dB/octave

Crossover Network 1.7k Hertz, 18 dB/octave electrical slope, HF driver power limiting circuit (never disrupts continuity). Swit-

chable operation between Bi-Amp and Tri-amp operation. Tri-amp setting removes crossover circuit from

signal, leaving power limiter and DC blocking capacitors.

Connectors Barrier strip screw terminals accept up to #10 AWG stranded wire. Four terminals, two HF input and two

MF input (for Tri-amp mode operation).

Transducers MF: 10" high efficiency midrange, phase-ring loaded.

HF: 1.5" (38mm) exit, 2.5" (63.5mm) titanium diaphragm compression driver.

Mounting Hardware: Attaches to top of the low frequency cabinet using three 5/16”-18 x 3/4” long bolts.

Size 39” high x 30” wide x 20” deep (991 x 762 x 508mm)

Weight 85 lb. (39 kg) net

MH-1075 Specifications (subject to change without notice

Freq. Range 180 - 15k (-6dB, full space)

Nominal Coverage 90° horizontal X +20 to -30° vertical (50° total, adjustable mount provides for vertical plane adjustments.

The horizontal plane can be adjusted by altering mounting position on the low frequency enclosure before

tightening bolts.

DI: 9 dB (400 to 16k Hertz average)

Q: 8 (400 to 16k Hertz average)

Max. Output: [Tri-amp mode] Mid Freq. 135.5 dB SPL calculated peak, 1m, full space

[Tri-amp mode] High Freq. 133 dB SPL calculated peak, 1m, full space

[Bi-amp mode] 135.5 dB SPL calculated peak, 1m ,full space

Impedance: [Bi-amp mode] 8 ohms nominal

6.4 ohms minimum at 1500 Hertz

91 ohms maximum at 150 Hertz

Maximum Input Power [Tri-amp mode] Mid Freq. 275 W (AES method, 2 hrs.)

[Tri-amp ode] High Freq. 80 W (AES method, 2 hrs.)

[Bi-amp mode] 250 W (IEC method, 8 hrs.)

Sensitivity [Tri-amp mode] Mid Freq. 105 dB SPL, 1 watt, 1 meter

[Tri-amp mode] High Freq. 108 dB SPL, 1 watt, 1 meter

[Bi-amp mode] 135.5 dB SPL, 1 watt, 1 meter

Crossover Frequencies [Tri-amp mode] 250 Hertz or higher, 24dB/octave and 1.7k Hertz, 24dB/octave

[Bi-amp mode] 250 Hertz or higher, 24dB/octave

Crossover Network 1.7k Hertz, 18 dB/octave electrical slope, HF driver power limiting circuit (never disrupts continuity). Swit-

chable operation between Bi-Amp and Tri-amp operation. Tri-amp setting removes crossover circuit from

signal, leaving power limiter and DC blocking capacitors.

Connectors Barrier strip screw terminals accept up to #10 AWG stranded wire. Four terminals, two HF input and two

MF input (for Tri-amp mode operation).

Transducers MF: 10" high efficiency midrange, phase-ring loaded.

HF: 1.5" (38mm) exit, 3" (76mm) titanium diaphragm compression driver.

Mounting Hardware: Attaches to top of the low frequency cabinet using three 5/16”-18 x 3/4” long bolts.

Size 39” high x 30” wide x 20” deep (991 x 762 x 508mm)

Weight 85 lb. (39 kg) net

MH-1075 SPL and Impedance vs. Frequency

SPL (dB)

Frequency (Hertz)

Impedance (Ohms)

Impedance

SPL

MH-1063 SPL and Impedance vs. Frequency

SPL

Impedance

SPL (dB)

Frequency (Hertz)

Impedance (Ohms)

Warranty (USA only; other countries, see your dealer or distributor)

Disclaimer

QSC Audio Products, Inc. is not liable for any damage to amplifiers, or any other equipment that is caused by negligence or

improper installation and/or use of this loudspeaker product.

QSC Audio Products 3 Year Limited Warranty

QSC Audio Products, Inc. (“QSC”) guarantees its products to be free from defective material and / or workmanship for a period

of three (3) years from date of sale, and will replace defective parts and repair malfunctioning products under this warranty

when the defect occurs under normal installation and use - provided the unit is returned to our factory or one of our authorized

service stations via pre-paid transportation with a copy of proof of purchase (i.e., sales receipt). This warranty provides that

the examination of the return product must indicate, in our judgment, a manufacturing defect. This warranty does not extend

to any product which has been subjected to misuse, neglect, accident, improper installation, or where the date code has been

removed or defaced. QSC shall not be liable for incidental and/or consequential damages. This warranty gives you specific

legal rights. This limited warranty is freely transferable during the term of the warranty period.

Customer may have additional rights, which vary from state to state.

In the event that this product was manufactured for export and sale outside of the United States or its territories, then this lim-

ited warranty shall not apply. Removal of the serial number on this product, or purchase of this product from an unauthorized

dealer, will void this limited warranty. Periodically, this warranty is updated. To obtain the most recent version of QSC’s war-

ranty statement, please visit www.qscaudio.com. Contact us at 800-854-4079 or visit our website at www.qscaudio.com.

Contacting QSC Audio Products

Mailing address:QSC Audio Products, Inc.

1675 MacArthur Boulevard

Costa Mesa, CA 92626-1468 USA

Telephone Numbers:

Main Number (714) 754-6175

Sales & Marketing (714) 957-7100 or toll free (USA only) (800) 854-4079

Customer Service(714) 957-7150 or toll free (USA only) (800) 772-2834

Facsimile Numbers:

Sales & Marketing Fax(714) 754-6174

Customer Service Fax(714) 754-6173

World Wide Web:www.qscaudio.com

E-mail:[email protected]

[email protected]

QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA

*TD-000141-00*

Cinema Loudspeaker Systems User Manual

LF-4215 Low Frequency Loudspeaker

Introduction

The LF-4215 dual 15” (381mm) low frequency enclosure is designed specifically for cinema

applications. Meeting cinema requirements for extended low frequency response differenti-

ates the LF-4215 from more conventional “rock-and-roll” woofer systems. The LF-4215 cov-

ers the frequency range from 35 Hertz to 1000 Hertz, depending upon the high frequency

system requirements. Close Coupled Woofers (CCW), with its tight spacing between woof-

ers, improves coupling and keeps coverage angles wide over a greater frequency range than

more widely spaced designs.

The two custom 400 watt, 15” transducers were developed especially for cinema use. They

feature extremely large 4” (100mm) voice coils and a multi-vented pole piece to ensure cool

operation, even at high power levels. Cooler temperatures increase transducer lifespan and

decrease the problem of power compression at high power. An undercut pole piece ensures

the voice coil operates in a Symmetrical Magnetic Gap (SMG), reducing second harmonic

distortion.

The enclosure is constructed of high quality MDF panels and features Single Woofer Cham-

bers (SWC, separate chambers for each transducer). In the rare event of a transducer failure,

this prevents over-excursion of the remaining transducer caused by improper box loading.

Large, Fully Radiused Ports (FRP) ensure smooth air flow through the ports, especially at

higher power. This prevents potentially audible port turbulence noise. Both internal and

external port openings are fully radiused.

With Symmetrical Port Loading (SPL), bass ports are evenly spaced on each side of the trans-

ducers, making internal pressure more uniform across the back surface of the transducer.

This prevents the cone from being displaced to one side or another by unbalanced forces,

reducing the chance of driving the voice coil out of the center of the gap at high power.

Three T-nuts in the top of the enclosure provide easy mounting of QSC’s HF-75 high fre-

quency system, or MH-1075 mid-high system.

Enclosure is not designed to be suspended, flown, or rigged. Do not sus-

pend, fly, or rig this enclosure.

This product is capable of producing sound pressure levels that can perma-

nently damage human hearing. Always keep sound pressure levels in the

listening area below levels that can damage human hearing.

Install in accordance with QSC Audio Product’s instructions and a

licensed, professional engineer. Only use attachments, mounts, accesso-

ries, or brackets specified by QSC Audio Products, Inc. Refer all servicing

to qualified personnel. Servicing is required when the apparatus has been

damaged in any way.

WARNING! Before placing, installing, rigging, or suspending any speaker

product, inspect all hardware, suspension, cabinets, transducers, brackets

and associated equipment for damage. Any missing, corroded, deformed or

non-load rated component could significantly reduce the strength of the

installation, placement, or array. Any such condition severely reduces the

safety of the installation and should be immediately corrected. Use only

hardware which is rated for the loading conditions of the installation and

any possible short-term unexpected overloading. Never exceed the rating

of the hardware or equipment. Consult a licensed, professional engineer

when any doubt or questions arise regarding a physical equipment installa-

tion.

TD-000141-00 rev.D

QSC® is a registered trademark of QSC Audio Products, Inc.

“QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office

1675 MacArthur Blvd., Costa Mesa, CA, 92626 USA

Main Number (714) 754-6175 Sales & Marketing (714) 957-7100 or toll free (USA only) (800) 854-4079

Customer Service(714) 957-7150 or toll free (USA only) (800) 772-2834

Mounting points for high

or mid-high system

Connections

Normal Connection

The LF-4215 has barrier strip screw termi-

nals for connection. The terminals accept

up to #10 AWG stranded loudspeaker wir-

ing. Use the largest wire size and shortest

wire length possible for a given installa-

tion. Observe the polarity markings and

keep polarity consistent throughout the

system for best performance.

Parallel Connection of Second SB-5218

The terminals marker SPK2 may be used to

connect another LF-4215 in parallel. Con-

nect the wires as shown in the illustration,

at right. Note: If the LF-4215’s internal wir-

ing has been modified in any way, this may

not function. If this is the case, remove the

terminal cup and verify the presence of the

factory yellow jumper and blue jumper

wires; remedy as required or have the

loudspeaker serviced.

Individual Transducer Connection

(requires modification)

The transducers are wired in parallel

inside the enclosure. If individual trans-

ducer connection is required, remove the

terminal cup and remove the yellow and

the blue jumper wires that are connected

between the SPK1 and SPK2 terminals.

Replace the terminal cup and mark the

enclosure with a note of the modification.

Normal Connection Example:

Parallel Connection Example:

Individual Transducer

Connection Example:

Amplifier capable of

driving 4 ohm loads

Amplifier capable of

driving 2 ohm loads

CAUTION!

Requires removal

of terminal cup

and cutting of both the

yellow and the blue

jumper wires that con-

nect the SPK1 and SPK2

terminals

Amplifier capable of

driving 2 ohm loads

LF-4215 Specifications (subject to change without notice)

Frequency Range: 38 - 1300 Hertz (±3 dB)

30 - 1400 Hertz useable range (-10 dB)

Nominal Coverage: 100° horizontal X 55° vertical at 600 Hertz

Maximum Output:

134.5 dB SPL calculated peak, 1 meter, half space, at rated rms power with 6 dB crest factor pink noise input, 25 - 250 Hertz.

128.5 dBA SPL calculated maximum continuous, 1 meter. The dBA scale is typically used to identify sound sources

which can cause permanent hearing loss.

Impedance: 4 ohms nominal

3.4 ohms minimum , 150 Hertz

25 ohms maximum, 22 Hertz

Maximum Input Power: 800 watts rms (100 hours of 6 dB crest factor pink noise, 30 - 500 Hertz)

1000 watts rms (2 hours of 6 dB crest factor pink noise, 30 - 500 Hertz, AES method)

recommended amplifier power capability- 1600 watts rms maximum into 4 ohms (per LF-4218)

Sensitivity: 99.5 dB half space, 93.5 dB full space, 35 - 1000 Hertz, 1 watt, 1 meter

Recommended Processing: Subsonic filter below 30 Hertz, >18 dB per octave, maximum recommended crossover frequency is 1000 Hertz. QSC

DSP configurations are available at www.qscaudio.com. Parameters for alternative processing hardware are available

upon request.

Connectors: Barrier strip screw terminals accept up to #10 AWG stranded wire. Four terminals: (two INPUT and two PARALLEL

OUT). Drivers are internally wired in parallel. For independent transducer connection, remove blue jumper wire and yel-

low jumper wire on internal-side of terminal cup and mark enclosure accordingly.

Transducers: Two 15” (381mm) high efficiency low frequency transducers featuring vented 4” (100mm) copper voice coils on Kap-

ton® formers. High excursion/low distortion design, with extremely high power handling, and low thermal and port

compression.

Enclosure: Quasi B4 alignment, ported enclosure with fully flared ports, low turbulence symmetrical port design, tuned to 36

Hertz, constructed of medium density fibreboard and heavily braced. Features vandal resistant woofer mounting bolts.

Size: 30” wide X 35” high X 20” deep (762 mm X 889 mm X 508 mm)

Weight: 195 lbs. shipping, 172 lbs. net (88/78 kg.)

SPL and Impedance vs. Frequency

Frequency (Hertz)

SPL (dB)

Impedance (ohms)

SPL 2pi

Impedance

SPL 4pi