Kohler K-1164-S1GW-0 Guide d'installation

Marque: Kohler

Modèle: K-1164-S1GW-0

Taper: Guide d'installation

Ce manuel convient également à

Installation and Care Guide

Bath with Airjets with Heated Surface

Retain serial number for reference:

Conserver le numéro de série pour référence:

Guarde el número de serie para

referencia:__________________________

Français, page “Français-1”

Español, página “Español-1”

1204119-2-D

Installation Instructions

WARNING: When using electrical products, basic precautions should always be followed,

including the following:

DANGER: Risk of electric shock. Connect only to a circuit protected by a Ground-Fault

Circuit-Interrupter (GFCI)*.

Building materials and wiring should be routed away from the blower body and other heat-producing

components of the unit.

Install to permit access for servicing.

A pressure wire connector marked ″Earth/Ground″ is provided within the wiring compartment. To reduce

the risk of electric shock, connect this connector to the grounding terminal of your electric service or supply

panel with copper wire equivalent in size to the circuit conductor supplying this equipment.

A pressure wire connector is provided on the exterior of the pump or control within this unit to permit

connection of a bonding conductor between this unit and all the other exposed metal in the vicinity, as

needed to comply with local requirements.

Grounding is required. The unit should be installed by a qualiﬁed service representative, and grounded.

WARNING: Risk of injury or property damage. Please read all instructions thoroughly before

beginning installation, including the following requirements.

WARNING: Risk of electric shock. A qualiﬁed electrician should make all electrical connections.

WARNING: Risk of electric shock. Disconnect power before servicing.

NOTICE: Follow all local plumbing and electrical codes. In Canada, install this unit in accordance with

the Canadian Electrical Code, Part 1.

*Outside North America, this device may be known as a Residual Current Device (RCD).

Product Information

Electrical Requirements

WARNING: Risk of burns, ﬁre, electric shock, or injury. Do not operate the heater if the power

supply cord is damaged. For proper guidance to have this product repaired, please call:

1-800-4KOHLER from within the USA or Canada, or 001-800-456-4537 from within Mexico.

The installation must have a Class A Ground-Fault Circuit-Interrupter (GFCI). The GFCI protects against

line-to-ground shock hazard. Use a 120 V, 15 A, 60 Hz dedicated service for the bath.

If the blower supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualiﬁed persons in order to avoid a hazard.

Product Notices

NOTICE: Keep the area around the blower clean and free of debris. Ensure that the area around the

blower is free of sawdust, insulation, dirt, and other small loose debris. Such material can block the blower

air ducts and reduce the air ﬂow through the blower.

NOTICE: This product contains an automatic water purge mode that turns the blower on for 2 minutes

about 30 minutes after the unit is turned off and drained.

1204119-2-D 2 Kohler Co.

Product Information (cont.)

Features

Factory-installed components include a blower motor with power supply cord, air piping, check valve (some

models), user keypad, and a heated surface with power supply cord, user keypad, and keypad cable. Other

than electrical wiring and plumbing, no assembly is needed.

Tools and Materials

100% Silicone Sealant

Plus:

• Conventional Woodworking

Tools and Materials

• Drop Cloth

• Construction Adhesive (Optional)

• Cement* or Mortar (Optional)

• 2x4s

* Do not use gypsum cement.

Kohler Co. 3 1204119-2-D

1. Prepare the Site

NOTICE: Measure your actual product for site preparation. Note the model number located on the bath

blower, then visit the product page at www.kohler.com for additional information.

NOTICE: Remote blower installation kit K-1446 is available for relocating the blower.

NOTICE: Provide generous, unrestricted access to the blower. You must provide access for servicing the

blower. The access must be located immediately next to the blower.

NOTICE: Do not lift the bath by the piping or blower, or use the piping or blower for structural support

of the bath. To avoid damage to the bath, lift by the rim at the sides of the bath.

NOTICE: Do not support the weight of the bath by the rim.

NOTICE: Drop-in models are not intended for alcove installation. Use a ﬂanged model for alcove

installations.

NOTE: Drop-in, alcove, or corner installation is possible, depending on the product chosen.

Carefully unpack and inspect the new bath for damage before installation. If there is damage do not

install the bath; contact your dealer.

Make sure the ﬂooring offers adequate support for your bath, and verify that the subﬂoor is ﬂat and

level.

NOTE: For remote blower installations, refer to the installation instructions included with the remote

blower installation kit before proceeding.

Provide adequate ventilation and at least 15 cubic feet (.4 cubic meters) of open air space for cooling

the motor and supplying sufficient air to the blower. Do not position the blower motor closer than

1″ (25 mm) to the wall or other objects.

Construct 2x4 stud framing.

Install an access panel for future blower servicing. The access panel must be at least 30″ (762 mm)

wide by 15″ (381 mm) high.

Install the rough plumbing.

Install the drain to the bath according to the drain manufacturer’s instructions.

Protect the bath surface by positioning a clean drop cloth in the basin bottom.

Access

Panel

Construct according

to the product dimensions.

Construct 2x4

stud framing

according to the

product dimensions.

Position the

rough plumbing.

Verify that the subfloor

offers adequate support,

and is flat and level.

Alcove Drop-In

Position the

rough plumbing.

Verify that the subfloor

offers adequate support,

and is flat and level.

1204119-2-D 4 Kohler Co.

2. Install the Bath

NOTICE: Do not lift the bath by the piping or blower, or use the piping or blower for structural support

of the bath. To avoid damage to the bath, lift by the rim at the sides of the bath.

If the subﬂoor is not level, shim the bath support blocks or molded supports as necessary.

Option 1: Install Using Construction Adhesive

NOTE: Some models come with support blocks; some models have molded supports.

Apply a generous amount of high-quality construction adhesive to the bottom of the support blocks

or molded supports. With help, carefully lift the bath into position.

Option 2: Using a Cement or Mortar Bed

NOTE: Do not use gypsum cement or drywall compound for this application, as they will not provide an

acceptable, durable bond.

Set the basin area in 1″ (25 mm) to 2″ (51 mm) of mortar cement.

NOTE: The blower must rest directly on the subﬂoor. The blower should not be in contact with mortar.

Secure the Nailing-in Flanges (Alcove Units)

Drill a small pilot hole through the nailing-in ﬂange at each stud. Add shims as needed.

Use large-head galvanized nails to secure the nailing-in ﬂange to the studs.

Nail furring strips to the studs.

Install the Plumbing

Insert the drain tailpiece into the trap. Secure the drain tailpiece to the trap.

Install the faucet valve.

Check the drain connections for leakage.

Cement or

Mortar Bed

Clear a space

for the pump

and blower.

Option 1

Nail

Option 2

Alcove Installations

Support Blocks

Apply construction

adhesive.

Drill a small hole

through the nailing-in

flange at each stud.

Stud

Furring

Strip

Kohler Co. 5 1204119-2-D

3. Make the Electrical Connections

WARNING: Risk of electric shock. Make sure the power has been disconnected before performing

the following procedures.

WARNING: Risk of electric shock. Connect the junction box and blower to a properly grounded,

grounding-type duplex receptacle protected by a Ground-Fault Circuit-Interrupter (GFCI) or

Residual Current Device (RCD). Do not remove the grounding pins from the plugs. Do not use

grounding adapters.

NOTICE: The blower and junction box are equipped with cords and plugs. A qualiﬁed electrician must

install a GFCI- or RCD-protected, 120 V, 15 A, grounded duplex outlet. No other load should be on this

circuit.

Install a duplex electrical outlet behind the bath, at least 1-1/2″ (38 mm) above the subﬂoor, and

within reach of the 24″ (610 mm) power cord.

Plug the blower and junction box into this outlet.

4. Complete the Installation

Test Run the Bath

Operate the heated surface user keypad to test the temperature settings.

Fill the bath to a level at least 4″ (102 mm) above the top of the highest airjet.

Turn off the bath and let sit for ﬁve minutes. Check all bath piping connections for leaks. Check for

leakage along the front, sides, and back of the bath.

Turn on the blower and run for 5 minutes. Check for proper operation and function.

For additional information on bath and heated surface operation, see the ″Operating Instructions -

Heated Surface″ and ″Operating Instructions - Bath With Airjets″ sections.

Finish the Installation

Install water-resistant wallboard and all ﬁnished wall, deck, and ﬂoor materials.

Apply silicone sealant to seal all areas where the bath and ﬁnished wall or deck meet.

Install the faucet trim.

Clean-up After Installation

When cleaning up after installation, do not use abrasive cleansers, as they may scratch and dull the

bath surface. Use warm water and a liquid detergent to clean the surface of the bath.

Install a GFCI-protected

120 V, 15 A grounded outlet.

Bond in accordance

with applicable codes.

24" (610 mm)

Maximum Distance

Power

Supply

24" (610 mm)

Maximum Distance

Junction Box

1204119-2-D 6 Kohler Co.

Complete the Installation (cont.)

Remove stubborn stains or paint with turpentine or paint thinner. Do not allow cleaners containing

petroleum distillates to remain in contact with any bath surface for long periods of time. Remove

plaster by carefully scraping with a wood edge. Do not use metal scrapers, wire brushes, or other

metal tools. Use a powder-type detergent on a damp cloth to provide mild abrasive action to any

residual plaster.

Important Safety Instructions

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

WARNING: When using electrical products, basic precautions should always be followed,

including the following:

DANGER: Risk of accidental injury or drowning. To reduce the risk of injury, do not permit

children to use this unit unless they are closely supervised at all times.

WARNING: Risk of personal injury. To avoid injury, exercise care when entering or exiting the

bath.

WARNING: Risk of electric shock. Do not permit electric appliances (such as a hair dryer, lamp,

telephone, radio, or television) within 5’ (1.5 m) of this bath.

WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal

hyperthermia. Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs

when the internal temperature of the body reaches a level several degrees above the normal body

temperature of 98.6°F (37°C). The symptoms of hyperthermia include an increase in the internal

temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia

include: (a) failure to perceive heat, (b) failure to recognize the need to exit the bath, (c)

unawareness of impending hazard, (d) fetal damage in pregnant women, (e) physical inability to

exit the bath, and (f) unconsciousness resulting in the danger of drowning.

WARNING: Risk of fetal injury. Pregnant or possibly pregnant women should consult a physician

before using the bath.

WARNING: Risk of hyperthermia or drowning. Do not use the bath immediately following

strenuous exercise.

WARNING: Risk of hyperthermia or drowning. Water temperature in excess of 100°F (38°C) may

cause injury. Test and adjust the water temperature before use.

WARNING: Risk of personal injury. Never drop or insert any object into any opening.

Use this bath only for its intended purpose as described in this guide. Do not use attachments not

recommended by Kohler Co.

The bath must be connected only to a supply circuit that is protected by a Ground-Fault Circuit-Interrupter

(GFCI)*. Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the

GFCI, press the test button. The GFCI should interrupt power. Press the reset button. Power should be

restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to

the bath without the test button being pressed, a ground current is ﬂowing, indicating the possibility of an

electric shock. Do not use this bath. Disconnect the bath and have the problem corrected by a qualiﬁed

service representative before using.

Kohler Co. 7 1204119-2-D

Important Safety Instructions (cont.)

Flush your whirlpool system twice a month or more depending upon usage, as described in the ″Flush the

System″ section of this guide.

Repeated use of personal care products containing oils can damage plastic whirlpool components. Avoid

using bath oils.

Whirlpool hydro-massage action can cause even a small amount of bubble bath, bath soap, shampoo, or bath

oil to foam excessively. For this reason, please do not use these products during whirlpool operation.

*Outside North America, this device may be known as a Residual Current Device (RCD).

1204119-2-D 8 Kohler Co.

Operating Instructions - Heated Surface

Keypad Operation

Power Icon - Turns the heater on and off.

Heat/Temperature Indicator - The [Flame] icon illuminates yellow, orange, or red depending on the

heat level. Yellow indicates low heat, orange indicates medium heat, and red indicates high heat.

Up Arrow - Increases the temperature.

Down Arrow - Decreases the temperature.

NOTICE: The heater will remain on until it is manually turned off by pressing the [Power] icon.

NOTE: After 60 minutes of inactivity, the heater will automatically reset to low heat if the temperature

was set to medium or high.

NOTE: The heater will turn on at the last selected temperature setting.

Error Codes

Heat indicator blinking red - The heater is not functioning.

Heat indicator blinking yellow - The temperature sensor is not functioning or is loose.

Refer to the ″Troubleshooting″ section to troubleshoot any problems.

Conﬁrm Heating System Operation

Press the [Power] icon on the user keypad.

Observe that the heat indicator turns yellow and the heater produces low heat.

Press the [Up] arrow. Verify that the heat indicator turns orange and the temperature increases.

Press the [Up] arrow a second time. Verify that the heat indicator turns red and the temperature

increases.

Press the [Down] arrow. Verify that the heat indicator turns orange and the temperature decreases.

Press the [Down] arrow a second time. Verify that the heat indicator turns yellow and the

temperature decreases.

Press the [Power] icon to turn the heater off.

Increase Temperature

Decrease TemperaturePower On/Off

Heat/Temperature Indicator

Kohler Co. 9 1204119-2-D

Operating Instructions - Bath With Airjets

IMPORTANT! This product contains an automatic water purge mode that turns the blower on for 2

minutes approximately 30 minutes after the unit is turned off and drained.

NOTE: The water temperature in the bath should never exceed 104°F (40°C).

Close the drain, then ﬁll the bath at least 4” (102 mm) above the top of the highest airjet.

Use your hand to test the water temperature for comfort and safety, then carefully enter the bath.

Press the [On/Off] icon to turn the blower on at medium speed.

Press the [Up] or [Down] arrow icons to increase or decrease the air ﬂow.

NOTE: The blower will turn off automatically following 20 minutes of operation, and can be immediately

restarted if desired.

Press the [On/Off] icon a second time to turn off the blower.

Carefully exit and drain the bath.

Press the [Purge Mode] icon to blow remaining water from the air channels. The blower will turn

on for 2 minutes and then turn off automatically.

NOTE: About 30 minutes after the blower motor stops, a 2 minute purge mode will automatically start.

NOTE: If the bath does not function properly, refer to the ″Troubleshooting″ section.

Care and Cleaning

Do not use powdered cleaners unless the cleaner is fully dissolved in water. Solid substances

could block the airjets.

Do not use full strength bleach or ammonia cleaning solutions. Chemically active cleaning

solutions can damage the bath surface.

Do not use abrasive cleansers or solvents on acrylic surfaces. Abrasive cleaners and solvents can

damage the bath surface.

Wipe out your acrylic bath with a soft cloth after each use.

Avoid detergents, disinfectants, or cleaning products in aerosol cans.

NOTE: To restore dull or scratched units: Apply white automotive polishing compound with a clean rag.

Rub scratches and dull areas vigorously. Wipe off residue. Follow with a coat of white automotive paste

wax. Do not wax areas where you walk or stand.

Purge Mode

On/Off

Increases Flow

Decreases Flow

1204119-2-D 10 Kohler Co.

Care and Cleaning (cont.)

Cleaning Your User Keypad and Remote Control

Use a soft cloth to wipe the keypad and remote control after each use. If the surface becomes dirty,

use a non-abrasive soap and warm water to clean.

Maintaining the Airjets

If cleaning the airjets is required due to hard water deposits, use a small between-the-teeth dental

brush and white vinegar. Dip the brush in the vinegar, brush the hole, rinse the brush in clean

water, and then use the wet rinsed brush to rinse the hole.

Fill the bath with water to the top row of airjets. Drain the bath and press the purge button.

For detailed cleaning information and products to consider, visit www.kohler.com/clean. To order Care &

Cleaning information, call 1-800-456-4537.

Troubleshooting

NOTICE: This section is for general aid only. A Kohler Co. Authorized Service Representative or

qualiﬁed electrician should correct any electrical problems. For warranty service, call 1-800-4KOHLER

from within the USA and Canada, or 001-800-456-4537 from within Mexico.

For service parts information, visit your product page at www.kohler.com/serviceparts.

Bath With Airjets System

Symptoms Probable Causes Recommended Action

1. Blower turns on by itself

after the bath has been

drained.

A. Normal operation. Automatic

purge mode is working as

designed.

A. No action is required. Automatic

purge mode runs for 2 minutes 30

minutes after the bath is drained.

2. Blower turns off by itself

after running for 2

minutes.

A. The Purge Mode icon was

pressed instead of the On/Off

icon.

A. Press the On/Off icon on the

keypad. See the ″Operating

Instructions″ section.

3. Blower motor will not

start.

A. Power cord from blower motor

is loose, disconnected, or

damaged.

A. Check wiring for proper

connections.

B. User keypad cable loose or

damaged.

B. Check wire connections. If

necessary, replace user keypad

cable.

C. User keypad does not work. C. Replace user keypad.

D. Blower motor does not work. D. Replace the blower motor.

4. Blower motor stops

running and will not

immediately restart.

A. Blower motor overheated and

protection device activated.

A. Check for blockage at blower air

intake. Remove blockage and allow

motor to cool.

5. Blower motor starts, some

but not all airjets are

working.

A. Blower motor speed is too low. A. Increase speed.

B. Blower motor inlet is blocked. B. Clean blower motor inlet.

C. Blower motor does not work. C. Replace the blower motor.

D. Blower motor discharge is

blocked.

D. Clear blockage.

E. Airjets are clogged. E. Use a small between-the-teeth

dental brush and white vinegar.

Dip the brush in the vinegar, brush

the hole, rinse the brush in clean

water, and then use the wet rinsed

brush to rinse the hole.

Kohler Co. 11 1204119-2-D

Troubleshooting (cont.)

Symptoms Probable Causes Recommended Action

6. Blower motor runs but no

air bubbles are observed.

A. Blower motor inlet is blocked. A. Clean blower motor inlet.

B. Airjets are clogged. B. Use a small between-the-teeth

dental brush and white vinegar.

Dip the brush in the vinegar, brush

the hole, rinse the brush in clean

water, and then use the wet rinsed

brush to rinse the hole.

C. Blower motor does not work. C. Replace the blower motor.

7. Blower motor operates,

air bubbles are observed,

but speed feature does

not work.

A. Blower motor inlet is blocked. A. Clean blower motor inlet.

B. Loose, disconnected, or

damaged wiring harness.

B. Check wiring for proper

connections. Replace the wiring

harness if necessary.

C. User keypad does not work. C. Replace the user keypad.

D. Blower motor does not work. D. Replace the blower motor.

8. Blower motor does not

turn off when the On/Off

button is pressed.

A. User keypad does not work. A. Replace the user keypad.

B. Loose, disconnected, or

damaged wiring harness.

B. Check wiring for proper

connections. Replace the wiring

harness if necessary.

C. Control does not work. C. Replace the control.

9. Purge mode does not

work.

A. User keypad does not work. A. Replace the user keypad.

B. Control does not work. B. Replace the control.

10. Bath does not purge

automatically.

A. Blower does not work. A. Replace the blower.

Heated Surface

Symptoms Probable Causes Recommended Action

11. Heated bath does not turn

on.

A. No power to power supply. A. Set/reset GFCI or RCD breaker;

check wiring.

B. User keypad cable loose or

damaged.

B. Check wire connections. If

necessary, replace user keypad

cable.

C. User keypad does not work. C. Check wire connections. Replace

user keypad.

D. Power supply does not work. D. Replace power supply.

12. Bath is turned on, but

there is little or no heat.

A. Heater cable loose or damaged. A. Check wire connections. If

necessary, replace heater cable.

B. Heater/insulation loose on the

bath.

B. Secure the heater/insulation to the

bath.

C. Heat indicator is yellow or

orange.

C. Press the [Up] arrow to increase

temperature.

D. Heater does not work. D. Replace the heater.

E. Temperature sensor does not

work.

E. Replace the heater.

13. Temperature does not

automatically reset to low

after 1 hour.

A. Temperature sensor does not

work.

A. Replace the heater and/or keypad.

14. Heat indicator is blinking

red.

A. Heating system needs to be

reset.

A. Press the [Power] icon to turn the

power off. Wait 10 seconds, then

turn the power on.

B. Heater does not work. B. Replace the heater.

15. Heat indicator is blinking

yellow.

A. Heating system needs to be

reset.

A. Press the [Power] icon to turn the

power off. Wait 10 seconds, then

turn the power on.

1204119-2-D 12 Kohler Co.

Troubleshooting (cont.)

Symptoms Probable Causes Recommended Action

B. Temperature sensor does not

work.

B. Replace the heater.

Warranty

ONE-YEAR LIMITED WARRANTY

KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year

from date of installation.

Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection

discloses any such defects occurring in normal usage within one (1) year after installation. Kohler Co. is not

responsible for removal or installation costs. Use of in-tank toilet cleaners will void the warranty.

To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home

Center or E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI

53044, USA, or by calling 1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and

001-800-456-4537 from within Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from

within Canada, or www.mx.kohler.com in Mexico.

IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE DURATION OF THIS

WARRANTY. KOHLER CO. AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL,

INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states/provinces do not allow limitations on how

long an implied warranty lasts, or the exclusion or limitation of special, incidental or consequential damages,

so these limitations and exclusions may not apply to you. This warranty gives you speciﬁc legal rights. You

may also have other rights which vary from state/province to state/province.

This is Kohler Co.’s exclusive written warranty.

Warranty

For Mexico

KOHLER CO.

It is recommended that at the time of purchase, you verify that all accessories and components are complete

in this package.

This Kohler product is warranted to be free of defects in material and workmanship for one (1) year from the

date of purchase as shown on the invoice or receipt.

1. Kohler Co. will only service its commercialized products through its authorized distributors.

2. To obtain warranty service, please present the invoice and corresponding warranty.

3. Through its authorized distributors, Kohler Co. promises to repair the defective product or provide a new

replacement or an equivalent model (in those cases that the model has been discontinued) when the product

is beyond repair, without any charge to the consumer.

4. The time of repair will not exceed six (6) weeks commencing on the date the product is received.

5. It is recommended that the consumer save the invoice or receipt as additional protection, as it may

substitute the warranty in the case that there is a discrepancy in the validity of the warranty.

EXCEPTIONS AND RESTRICTIONS

The Warranty will not be valid in the following cases:

1. When the product is not operated in accordance with the instructions concerning use and operation set

Kohler Co. 13 1204119-2-D

Warranty (cont.)

forth in the owner’s manual or installation instructions, and when the recommendations and warnings

included are not observed.

2. When the product has been modiﬁed or dismantled partially or totally; or has been used in a negligent

fashion and as a consequence has suffered damages attributable to the consumer, individual, or hardware not

authorized by Kohler Co.

3. This warranty does not cover the damages as a result of disaster such as ﬁre or acts of God, including

ﬂooding, earthquake, or electric storms, etc. To obtain a list of distributors in your area where you can

exercise your rights under this warranty, please call 001-800-456-4537.

KOHLER CO., KOHLER, WI 53044 U.S.A.

IMPORTER:

COMERCIALIZADORA INTERCERAMIC, S.A. DE C.V.

AV. CARLOS PACHECO NO. 7200, COL. MADERA 65

CHIHUAHUA, CHIH., MEXICO C.P. 31060

R.F.C. CIN141022IE9

TEL: 52 (614) 429-11-11

IMPORTER:

GAMA MATERIALES Y ACEROS, S.A. DE C.V.

AVE LOS ANGELES NO. 1800

COL VALLE DEL NOGALAR, SAN NICOLAS DE LOS GARZA

N.L. MEXICO

R.F.C. GMA901220U11

TEL: 81-1160-5500

1204119-2-D 14 Kohler Co.

Guide d’installation et d’entretien

Baignoire avec jets d’air et surface chauffée

Instructions d’installation

AVERTISSEMENT: Lors de l’utilisation de produits électriques, toujours observer les

précautions de base, notamment:

DANGER: Risque de choc électrique. Raccorder uniquement à un circuit protégé par un

disjoncteur de fuite de terre (GFCI)*.

Les matériaux de construction et le câblage doivent être acheminés loin du souffleur et des autres

composants qui dégagent de la chaleur de l’appareil.

Installer de façon à permettre un accès pour l’entretien.

Un connecteur à pression pour câbles marqué ″Earth/Ground″ (Terre/Masse) est fourni dans le

compartiment de câblage. Aﬁn de réduire les risques de choc électrique, raccorder ce connecteur à une borne

de terre du panneau de service électrique ou du panneau d’alimentation avec un câble en cuivre ayant la

même dimension que le conducteur du circuit qui alimente cet équipement.

Un connecteur à pression pour câbles est fourni à l’extérieur de la pompe ou de la commande de cet appareil

aﬁn de permettre la connexion d’un conducteur de mise à la terre entre cet appareil et toutes les autres

surfaces de métal avoisinantes, tel que requis par les réglementations locales.

Une mise à la terre est requise. L’appareil doit être installé par un représentant qualiﬁé et doit être mis à la

terre.

AVERTISSEMENT: Risque de blessures ou d’endommagement du matériel. Toutes les

instructions doivent être lues avec la plus grande attention avant de commencer l’installation, et

toutes les conditions suivantes doivent être respectées.

AVERTISSEMENT: Risque de choc électrique. Un électricien qualiﬁé doit effectuer toutes les

connexions électriques.

AVERTISSEMENT: Risque de choc électrique. Déconnecter l’alimentation électrique avant

d’effectuer un entretien.

AVIS: Respecter tous les codes de plomberie et électriques locaux. Installer cet appareil conformément

au Code canadien de l’électricité, Partie 1.

* Hors de l’Amérique du Nord, ce dispositif peut être connu sous le nom de dispositif à courant résiduel

(RCD).

Information sur le produit

Installations électriques requises

AVERTISSEMENT: Risque de brûlures, d’incendie, d’électrocution ou de blessures. Ne pas faire

fonctionner le chauffage si le cordon d’alimentation est endommagé. Pour obtenir une assistance

adéquate pour la réparation de ce produit, appeler: 1-800-4KOHLER à partir des É.-U. ou du

Canada, ou le 001-800-456-4537 à partir du Mexique.

Cette installation doit être munie d’un disjoncteur de fuite de terre (GFCI) de classe A. Le disjoncteur GFCI

protège contre les risques d’électrocution ﬁl sous tension-terre. Utiliser une alimentation de 120 V, 15 A, 60

Hz dédiée à la baignoire.

Kohler Co. Français-1 1204119-2-D

Information sur le produit (cont.)

Si le câble d’alimentation du souffleur est endommagé, il doit être remplacé par le fabricant, son représentant

ou des professionnels qualiﬁés dans ce domaine aﬁn d’éviter tout danger.

Notices du produit

AVIS: Garder l’espace autour du souffleur propre et exempt de débris. S’assurer que l’espace autour du

souffleur est exempt de sciure, de matériau isolant, de saleté ou d’autres petits débris volatiles. De tels

matériaux pourraient boucher les conduits d’air du souffleur et réduire le débit d’air à travers le souffleur.

AVIS: Ce produit comprend un mode de purge d’eau automatique qui met le souffleur en marche

pendant 2 minutes, 30 minutes environ après l’arrêt et la vidange du dispositif.

Caractéristiques

Les composants installés à l’usine incluent un moteur de souffleur avec un cordon d’alimentation électrique,

une tuyauterie pneumatique, une soupape à clapet (certains modèles), un clavier utilisateur, et une surface

chauffée avec un cordon d’alimentation électrique, un clavier utilisateur, et un câble de clavier. Aucun

montage n’est nécessaire, sauf le câblage électrique et la plomberie.

Outils et matériel

Mastic à la silicone à 100%

Plus:

• Matériaux et outils à bois classiques

• Toile de protection

• Colle mastic (optionnelle)

• Ciment* ou mortier (optionnel)

• Des 2x4

* Ne pas utiliser de plâtre dur.

1204119-2-D Français-2 Kohler Co.

1. Préparer le site

AVIS: Mesurer le produit en question pour la préparation du site. Noter le numéro de modèle se

trouvant sur le souffleur de la baignoire, puis visiter la page des produits sur le site www.kohler.com pour

obtenir de l’information supplémentaire.

AVIS: Le kit K-1446 d’installation du souffleur à distance est disponible pour le changement de

positionnement du souffleur.

AVIS: Fournir un large espace non restreint pour pouvoir accéder au souffleur. Un accès doit être fourni

pour l’entretien du souffleur. L’accès doit être situé juste à côté du souffleur

AVIS: Ne pas soulever la baignoire par la tuyauterie ou le souffleur, et ne pas utiliser ceux-ci comme

support structurel de la baignoire. Aﬁn d’éviter tout endommagement de la baignoire, soulever celle-ci par

les côtés.

AVIS: Ne pas supporter le poids de charge de la baignoire par le rebord.

AVIS: Les modèles à encastrer par le dessus ne sont pas destinés à être installés en alcôve. Utiliser un

modèle à bride pour les installations en alcôve.

REMARQUE: Une installation à encastrer par le dessus, en alcôve ou en coin est possible, selon le produit

choisi.

Déballer et examiner soigneusement la nouvelle baignoire aﬁn d’y déceler tout dommage avant

d’effectuer l’installation. Si des dommages sont notés, ne pas installer la baignoire; contacter le

concessionnaire.

S’assurer que le plancher offre un support adéquat pour la baignoire et vériﬁer que le sous-plancher

est plat et nivelé.

REMARQUE: Pour les installations à distance du souffleur, consulter les instructions d’installation

accompagnant le kit d’installation du souffleur avant de continuer.

Fournir une ventilation adéquate et 15 pieds cube (0,4 mètre cube) au moins d’espace d’air ouvert

pour le refroidissement du moteur et pour fournir assez d’air au souffleur. Ne pas positionner le

moteur du souffleur à une distance plus proche de 1″ (25 mm) du mur ou d’autres objets.

Construire une charpente avec des montants de2x4.

Installer un panneau d’accès pour permettre un entretien futur de la pompe. Le panneau d’accès

doit avoir une largeur de 30″ (762 mm) et une hauteur de 15″ (381 mm) au moins.

Installer la tuyauterie de raccordement.

Installer le drain sur la baignoire conformément aux instructions du fabricant du drain.

Panneau

d'accès

Effectuer la construction selon

les dimensions du produit.

Construire une charpente

à montants de 2x4

selon les dimensions

du produit.

Positionner la plomberie

de raccordement.

Vérifier que le sous-plancher

offre un support adéquat et qu'il

est plat et nivelé.

Alcôve

À encastrer par le dessus

Positionner la plomberie

de raccordement.

Vérifier que le sous-

plancher offre un support

adéquat et qu'il

est plat et nivelé.

Kohler Co. Français-3 1204119-2-D

Préparer le site (cont.)

Protéger la surface de la baignoire en plaçant une toile de protection propre dans le bas du bassin.

1204119-2-D Français-4 Kohler Co.

2. Installer la baignoire

AVIS: Ne pas soulever la baignoire par la tuyauterie ou le souffleur, et ne pas utiliser ceux-ci comme

support structurel de la baignoire. Aﬁn d’éviter tout endommagement de la baignoire, soulever celle-ci par

les côtés.

Si le sous-plancher n’est pas nivelé, placer des blocs de support ou des supports moulés sous la

baignoire, selon les besoins.

Option 1: Effectuer l’installation en utilisant de la colle mastic

REMARQUE: Certains modèles sont dotés de blocs de support; d’autres modèles ont des supports

moulés.

Appliquer une quantité suffisante de colle mastic de haute qualité sur la base des blocs de support

ou des supports moulés. Avec de l’aide, lever la baignoire avec précaution et la positionner.

Option 2: Utilisation de lit de ciment ou de mortier

REMARQUE: Ne pas utiliser de plâtre dur ou un mélange pour cloison sèche pour cette installation, car

ces produits ne fournissent pas de scellement acceptable et durable.

Placer la zone du bassin dans du ciment à maçonner de 1″ (25 mm) à 2″ (51 mm).

REMARQUE: Le souffleur doit s’appuyer directement sur le sous-plancher. Le souffleur ne doit pas

entrer en contact avec le mortier.

Fixer les brides de cloutage en place (dispositifs en alcôve)

Percer un petit trou-pilote à travers la bride de cloutage de chaque montant. Utiliser des cales selon

les besoins.

Utiliser des clous galvanisés à grande tête pour ﬁxer la bride de cloutage sur les montants.

Clouer les tasseaux sur les montants.

Installer la plomberie

Insérer la pièce de raccordement du drain dans le siphon. Fixer l’about du drain sur le siphon.

Lit de ciment ou

de mortier

Dégager un espace

pour la pompe

et le souffleur.

Option 1

Clou

Option 2

Installations en alcôve

Blocs de support

Appliquer de la colle

mastic.

Percer un petit trou

dans la bride de cloutage

de chaque montant.

Goujon

Tasseau

Kohler Co. Français-5 1204119-2-D

Installer la baignoire (cont.)

Installer la vanne de robinet.

Rechercher des fuites dans les connexions du drain.

1204119-2-D Français-6 Kohler Co.

La page est en cours de chargement...

Kohler K-1164-S1GW-0 Guide d'installation

Marque: Kohler

Modèle: K-1164-S1GW-0

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Kohler K-1164-S1GW-0 Installation guide
español: Kohler K-1164-S1GW-0 Guía de instalación
português: Kohler K-1164-S1GW-0 Guia de instalação

Kohler K-1164-S1GW-0 Guide d'installation

Ce manuel convient également à

Kohler K-1164-S1GW-0 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents