Generac 6821 Manuel utilisateur

www.generac.com or 1-888-436-3722

Owner’s Manual

Water Pump

Model ST20

Model Number

Serial Number

Model CW15

ii

WARNING!

California Proposition 65

Engine exhaust and some of its constituents are known to the state of California to cause cancer,

birth defects, and other reproductive harm.

WARNING!

California Proposition 65

This product contains or emits chemicals known to the state of California to cause cancer,

birth defects, and other reproductive harm.

iii

Table of Contents

Section 1 - Introduction

1.1 - Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Section 2 - Safety

2.1 - Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Section 3 - General Information

3.1 - Know Your Water Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.2 - Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.3 - Emissions Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.4 - High Altitude Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.5 - Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Section 4 - Set-up

4.1 - Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4.2 - Add Engine Oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.3 - Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.4 - Connect Suction and Discharge Hose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.5 - Prime the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Section 5 - Operation

5.1 - Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5.2 - Water Pump Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5.3 - Checklist Before Starting Engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.4 - How to Start Your Water Pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.5 - How to Stop Your Water Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Section 6 - Maintenance

6.1 - Maintenance Recommendations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

6.2 - Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

6.3 - Emissions Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

6.4 - Water Pump Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

6.5 - Check Hose Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

0

6.6 - Check Hoses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

6.7 - Engine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

6.8 - Engine Oil Recommendations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

6.9 - Service Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

6.10 - Service Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6.11 - After Each Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6.12 - Long Term Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6.13 - Other Storage Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

6.14 - Transporting/Tipping of the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Section 7 - Troubleshooting

7.1 - Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

iv

Water Pump 1

1.1 — INTRODUCTION

Thank you for purchasing this water pump manufactured

by Generac Power Systems, Inc. This is a high perfor-

mance, air-cooled, engine-driven water pump that oper-

ates at 80 or 158 GPM depending on model.

Common sense and strict compliance with the spe-

cial instructions are essential to preventing acci-

dents. The operator must read this manual and

thoroughly understand all of the instructions and warn-

ings before using the equipment. If any portion of the

manual is not understood, contact the nearest Authorized

Dealer for starting, operating and servicing procedures.

The owner is responsible for proper and safe use of the

equipment.

The water pump can operate safely, efficiently and reli-

ably only if it is properly located, operated and main-

tained. Before operating, servicing or storing:

• Study all warnings in this manual and on the product

carefully.

• Become familiar with this manual and the unit before

use.

• Refer to the Assembly section of the manual for

instructions on final assembly procedures. Follow the

instructions completely.

The manufacturer cannot anticipate every possible cir-

cumstance that might involve a hazard. The warnings in

this manual, and on tags and decals affixed to the unit

are, therefore, not all inclusive. If using a procedure, work

method or operating technique that the manufacturer

does not specifically recommend, ensure that it is safe for

others. Also make sure the procedure, work method or

operating technique utilized does not render the water

pump unsafe.

THE INFORMATION CONTAINED HEREIN WAS

BASED ON MACHINES IN PRODUCTION AT THE

TIME OF PUBLICATION. GENERAC RESERVES THE

RIGHT TO MODIFY THIS MANUAL AT ANY TIME.

Save these instructions. If you loan this device to

someone, always loan these instructions and

Owner's Manual to individual as well.

1.1.1 — Where to Find Us

You can contact Generac Customer Service by phone at

1-888-436-3722, or on the internet at www.generac.com.

Record model and serial number of unit on front cover for

future reference and/or service inquiries.

Section 1 Introduction

2 Water Pump

This page intentionally left blank.

Introduction

Water Pump 3

2.1 — SAFETY RULES

Throughout this publication, and on tags and decals

affixed to the water pump, DANGER, WARNING, CAU-

TION and NOTE blocks are used to alert personnel to

special instructions about a particular operation that may

be hazardous if performed incorrectly or carelessly.

Observe them carefully. Their definitions are as follows:

Indicates a hazardous situation or action which, if

not avoided, will result in death or serious injury.

Indicates a hazardous situation or action which, if

not avoided, could result in death or serious injury.

Indicates a hazardous situation or action which, if

not avoided, could result in minor or moderate injury.

NOTE: Notes contain additional information import-

ant to a procedure and will be found within the regu-

lar text body of this manual.

These safety warnings cannot eliminate the hazards that

they indicate. Common sense and strict compliance with

the special instructions while performing the action or

service are essential to preventing accidents.Safety

Symbols and Meanings.

Figure 2-1. Exhaust Hazard

KickbackToxic Fumes Electrical Shock

Fluid InjectionFall

Fire Explosion Operator’s Manual

Slippery Surface

Moving Parts Flying Objects Hot Surface

Hearing Protection

Using engine powered equipment indoors CAN KILL

YOU IN MINUTES.

Engine exhaust contains carbon monoxide. This is a

poison you cannont see or smell.

Section 2 Safety

Safety

4 Water Pump

2.1.1 — Exhaust Hazards

Carbon monoxide produced during use can

kill in minutes. NEVER use indoors, in a vehi-

cle, or in other sheltered areas, EVEN IF doors

and windows are open. Only use OUTSIDE

and far away from windows, doors and vents.

• Operate water pump ONLY outdoors.

• A running engine gives off carbon monoxide.

• Carbon monoxide is an odorless, colorless, poisonous

gas. Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures, nau-

sea, fainting or death. If you start experiencing any of

these symptoms, IMMEDIATELY move to fresh air.

Seek medical attention.

• Keep exhaust gas from entering a confined area

through windows, doors, ventilation intakes, or other

openings. Warn any occupants inside about the symp-

toms of carbon monoxide so they know to move to

fresh air if they begin to feel ill.

• The use of a carbon monoxide detector inside any

occupied premises between the water pump and the

occupant is recommended.

• NEVER start or run engine indoors, in a vehicle, or in

an enclosed area, even if windows and doors are open.

• Use a respirator or mask whenever there is a chance

that harmful gas or vapors may be inhaled.

• Read all instructions with respirator or mask so you are

certain the respirator or mask will provide the neces-

sary protection against inhaling harmful gas or vapors.

If you begin to experience any of the CO symptoms

listed above, IMMEDIATELY move to fresh air.

2.1.2 — Electrical Shock Hazard

Risk of electrocution.

Contact with power source can cause electric

shock or burn.

• NEVER have discharge hose near power source.

2.1.3 — Hot Surfaces Hazard

Contact with muffler area can result in

serious burns. Exhaust heat/gases can

ignite combustibles, structures or

damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust

gases.

• Allow equipment to cool before touching.

• Keep at least five (5) feet (152 cm) of clearance on all

sides of water pump including overhead.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any for-

est-covered, brush-covered, or grass-covered land

unless the exhaust system is equipped with a spark

arrester, as defined in Section 4442, maintained in

effective working order. Other states or federal jurisdic-

tions may have similar laws. Contact the original equip-

ment manufacturer, retailer, or dealer to obtain a spark

arrester designed for the exhaust system installed on

this engine.

• Replacement parts must be the same and installed in

the same position as the original parts.

2.1.4 — Fire Hazards

Fuel and its vapors are extremely flam-

mable and explosive. Fire or explosion

can cause severe burns or death.

WHEN ADDING OR DRAINING FUEL

• Turn water pump OFF and let it cool at least two (2)

minutes before removing fuel cap. Loosen cap slowly

to relieve pressure in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting

engine.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner

are in place.

• DO NOT crank engine with spark plug removed.

• Keep your hands and body clear from the discharge of

the pump.

• Make sure all connections are tight.

• Secure the pump. Loads from the hoses may cause it

to tip over.

• Secure the discharge hose to avoid whipping.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which

causes fuel to spill.

Safety

Water Pump 5

• DO NOT pump chemicals or flammable liquids, such

as fuel, or fuel oils.

• Reflective exhaust heat may damage the fuel tank,

causing fire. Keep at least 5 feet of clearance on all

sides of the pump for adequate cooling, maintenance,

and servicing.

• DO NOT use to pump fluid intended for human con-

sumption.

• Secure the pump. Loads from the hoses may cause it

to tip over.

• DO NOT stop the engine by moving the choke lever to

the CHOKE position.

• Wear ear protection to reduce objectionable noise.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL

IN TANK

• Store away from furnaces, stoves, water heaters,

clothes dryers, or other appliances that have pilot light

or other ignition source because they can ignite fuel

vapors.

• DO NOT operate this pump dry!

• Excessively high operating speeds increase risk of

injury and damage to pump.

• Excessively low speeds impose a heavy load.

• DO NOT tamper with the governed speed.

• DO NOT modify the pump in any way.

• DO NOT allow unqualified persons or children to oper-

ate or service pump.

• DO NOT insert any objects through cooling slots.

• Treating the pump improperly can damage it and

shorten its life.

• Be sure pump chamber is filled with water before start-

ing the engine. NEVER run pump without priming.

• Use a non-collapsible hose on the suction side of the

pump.

• Use the pump only for its intended uses.

2.1.5 — Hearing Protection Hazard

Hearing Protection Recommended.

2.1.6 — Fall Hazard

Use of water pump can create puddles

and slippery surfaces.

• Use only on a level surface.

• The area should have adequate slopes and drainage

to reduce the possibility of a fall due to slippery sur-

faces.

• Do not use on elevated surfaces where there could be

a chance of a serious fall.

2.1.7 — Moving Parts Hazard

Starter and other rotating parts can entangle

hands, hair, clothing, or accessories.

• NEVER operate water pump without protective hous-

ing or covers.

• DO NOT wear loose clothing, jewelry or anything that

may be caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

2.1.8 — Kickback Hazard

Starter cord kickback (rapid retraction) can

result in bodily injury. Broken bones, frac-

tures, bruises, or sprains could result.

• When starting engine, pull cord slowly until resistance

is felt and then pull rapidly to avoid kickback.

2.1.9 — Spark Hazards

Unintentional sparking can result in

fire or electric shock.

WHEN ADJUSTING OR MAKING

REPAIRS TO YOUR WATER PUMP.

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Safety

6 Water Pump

2.1.10 — Splash Hazards

Risk of eye injury. Spray can splash back or

propel objects.

• Always wear safety goggles when using this equip-

ment or in vicinity of where equipment is in use.

• Before starting the water pump, be sure you are wear-

ing adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

NOTE: Improper treatment of water pump can dam-

age it and shorten its life.

• If you have questions about intended use, ask dealer

or contact qualified service center.

• NEVER operate units with broken or missing parts, or

without protective housing or covers.

• DO NOT by-pass any safety device on this machine.

• DO NOT operate water pump above rated head.

• DO NOT modify water pump in any way.

• Before starting water pump in cold weather, check all

parts of the equipment to be sure ice has not formed.

• NEVER move machine by pulling on hoses. Use han-

dle provided on unit.

• Check fuel system for leaks or signs of deterioration,

such as chafed or spongy hose, loose or missing

clamps, or damaged tank or cap. Correct all defects

before operating water pump.

• This equipment is designed to be used with Generac

authorized parts ONLY. If equipment is used with parts

that DO NOT comply with minimum specifications, user

assumes all risks and liabilities.

Water Pump 7

3.1 — KNOW YOUR WATER PUMP

Read this owner’s manual and safety rules before operat-

ing your water pump. If you loan this device to someone,

ALWAYS loan these instructions AND the owner’s man-

ual to the individual as well. Compare the illustrations

with your water pump to familiarize yourself with the loca-

tions of various controls (Figure 3-1). Save this manual

for future reference. Replacement owner’s manuals can

be printed from the Generac Web site.

A -Lifting Handle - Used to lift the water pump.

B -Discharge Port - Location to attach discharge hose.

C -Suction Port - Location to attach suction hose.

D -Water Drain Plug - Used to empty the water pump

after use.

E -Oil Fill - Check and add engine oil

F -Oil Drain Plug - Used to drain engine oil.

G -Muffler - Where hot exhaust gas exits the water

pump.

H-Fuel Tank - Fill tank with regular unleaded fuel.

Always leave room for fuel expansion.

I -Choke - Prepares a cold engine for starting.

J -Air Filter - Protects engine by filtering dust and

debris out of the intake air.

K-Recoil Starter - Used for starting the engine.

L -Engine ON/OFF Switch - Turn switch to ON before

using recoil starter. Turn switch to Off to stop engine.

M -Priming Cap - Remove cap and fill the pump with

water before starting the unit.

N -Fuel Gauge - Indicates the amount of fuel remaining

in the fuel tank.

O -Fuel On/Off Valve - Turns fuel supply to the engine

on and off.

P -Throttle Lever - Increases or decreases engine

speed.

Q -Serial number location

R -Blue Discharge Hose - Used to discharge water

from the pump

S -Hose Clamps - Secure the hose to the hose barbs

and the filter

T -Hose Nut - Secures the hose barb to the pump

U -Hose Barb - Holds the hose to the pump

V -Sealing Ring - Prevents leaking

W -Green Suction Hose - Used to bring water into the

pump

X -Filter Attachment - Used to connect filter basket to

the suction hose.

Y -Filter Basket - Used to keep debris out of the pump.

Figure 3-1. ST20 Features and Controls

H

G

OAPJI

K

L

F

E

D

C

B

M

N

Q

Section 3 General Information

General Information

8 Water Pump

Figure 3-2. CW15 Features and Controls

Figure 3-3. Features and Controls

H

I

J

M

K

L

B

C

D

A

G

E

F

Q

V

U

T

S

R

W

X

Y

General Information

Water Pump 9

3.2 — PRODUCT SPECIFICATIONS

3.3 — EMISSIONS INFORMATION

The U.S. Environmental Protection Agency (and Califor-

nia Air Resource Board for equipment certified to CA

standards) requires that this engine comply with exhaust

and evaporative emission standards. Locate the emis-

sions compliance decal on the engine to determine what

standards the engine meets, and to determine which

emissions warranty applies. The engine is certified to

meet the applicable emission standards on gasoline. It is

important to follow the maintenance specifications in the

Maintenance section to ensure that the engine complies

with the applicable emission standards for the duration of

the product’s life. This engine utilizes lean carburetion

settings and other systems to reduce emissions. Tamper-

ing with or altering the emission control system may

increase emissions and may be a violation of Federal or

California Law. Acts that constitute tampering include but

are not limited to:

• Removal or alteration of any part of the intake, fuel, or

exhaust systems

• Altering or defeating the governor linkage or speed-

adjusting mechanism to cause the engine to operate

outside its design parameters

If you are aware of any of the following symptoms, have

your engine inspected and repaired by your servicing

dealer:

• Hard starting or stalling after starting

• Rough idle

• Misfiring or backfiring under load

• Afterburning (backfiring)

• Black exhaust smoke or high fuel consumption

3.4 — HIGH ALTITUDE OPERATION

The fuel system on this engine may be influenced by

operation at higher altitudes.

3.5 — UNPACKING

1. Remove the loose parts, kits, and inserts included

with water pump.

2. Open carton completely by cutting each corner from

top to bottom.

3. Ensure you have all included items prior to assembly.

• Main Unit

• Hose Kit

- Suction Hose

- Discharge Hose

- Hose Filter

- Hose Nut (2)

- Hose Clamp (3)

- Hose Barb (2)

- Sealing Ring (2)

• Loose Parts

- Oil Bottle

- Funnel

-Spark Plug wrench

- Operator’s Manual

- Owner’s Registration Card

• Wheel Kit (ST20K only)

- 8 inch wheel (2)

-Stub Axle (2)

- Washer (2)

-Cotter Pin (2)

- Handle

- Foot Bracket (2)

- M8x40 Flange Bolt (6)

- M8 Flange Nut (4)

4. If you are missing any items from your carton, please

call Generac Customer Service at 1-888-436-3722.

When calling for assistance, please have the model

and serial number from the data tag available.

5. Fill out and send in registration card. Write Model

number, Serial number & date of purchase in the

table located in the “Where to Find Us” section.

Model CW15K ST20K

Flow Rate (GPM / LPM) 80/303 158/598

Suction/Discharge Diameter (Inches/mm) 1.5/40 2/50

Total Head (feet/meter) 80/24.4 108/32.9

Suction Head (feet/meter) 26/7.9 26/7.9

Suction Hose Length (feet/meters) 10/3.1 12/3.7

Discharge Hose Length (feet/meters) 25/7.6 25/7.6

Engine Displacement (Cubic Inch/cc) 4.8/79 12.7/208

Spark Plug Type

E6RTC or

Equivalent

F6RTC or

Equivalent

Spark Plug Gap (Inches/mm) 0.028-0.031 / 0.70-0.80

Fuel Capacity (Gallon/Liters) 0.4/1.5 3/11.5

Oil Capacity (Oz/Liters) 13.5/0.4 20/0.6

Low Oil Shut Down System No Yes

On/Off Switch Yes

10 Water Pump

This page intentionally left blank.

General Information

Water Pump 11

4.1 — ASSEMBLY

Read entire operator’s manual before you attempt to

assemble or if you have any problems with the assembly

of your water pump, please call Generac Customer Ser-

vice at 1-888-436-3722. When calling for assistance,

please have the model and serial number from the data

tag available.

If the water pump does not include a wheel kit, skip

to “Add Engine Oil”.

You will need the following tools to install the vibration

mounts and handle:

• Socket wrench with 12 mm socket (not included)

1. Attach Vibration Mounts (feet) (Figure 4-1).

A. Attach the vibration mount to the frame using 2

Flange Bolts (M8x40) and 2 Nuts (M8).

B. Slide the bolts through the vibration mount and

through the frame.

C. Secure with nuts. Tighten, but do not over tighten.

D. Repeat A-C for the second vibration mount.

Figure 4-1. Vibration Mounts

2. Attach Handle (Figure 4-2).

A. Place the handle over the mounting plate of the

frame.

B. Secure the handle to the frame using 2 Flange

Bolts (M8x40).

Figure 4-2. Attach Handle

3. Attach wheels (Figure 4-3).

A. Slide the axle through the wheel, washer, and

then the mount point on the frame.

B. Insert the cotter pin through the hole in the end of

the axle.

C. Repeat A-B for the second wheel.

Figure 4-3. Attach Wheels

Section 4 Set-up

Set-up

12 Water Pump

4.2 — ADD ENGINE OIL

1. Place water pump on a flat, level surface.

2. Clean area around oil fill and remove ORANGE oil fill

cap/dipstick.

3. Using oil funnel, slowly pour oil into fill opening. See

“Maintenance” section for oil type recommendation.

4. Check periodically until the oil level is between “L”

and “H” on the dipstick (Figure 4-4). Do not overfill.

Figure 4-4. Dipstick

NOTE: Any attempt to crank or start the engine

before it has been properly serviced with the recom-

mend oil may result in engine failure.

5. Replace oil fill cap/dipstick and fully tighten.

4.3 — FUEL

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON).

• Gasoline with up to 10% ethanol (gasohol) is accept-

able.

NOTE: Avoid water pump damage. Failure to follow

Operator’s Manual for fuel recommendations voids

warranty.

• DO NOT use unapproved gasoline such as E85.

• DO NOT mix oil in gasoline.

• DO NOT modify engine to run on alternate fuels.

To protect the fuel system from gelling, mix in a fuel stabi-

lizer when adding fuel. See Storage. All fuel is not the

same. If you experience starting or performance prob-

lems after using fuel, switch to a different fuel provider or

change brands.

Fuel and its vapors are extremely flamma-

ble and explosive. Fire or explosion can

cause severe burns or death.

4.3.1 — ADDING FUEL

• Turn water pump OFF and let it cool at least two (2)

minutes before removing fuel cap. Loosen cap slowly

to relieve pressure in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting

engine.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• DO NOT light a cigarette or smoke.

1. Clean area around fuel fill cap, remove cap.

2. Slowly add regular unleaded fuel to fuel tank. Be

careful not to overfill. Fill to red indicator ring on the

fuel filter, this will allow for fuel expansion

(Figure 4-5).

3. Install fuel cap and let any spilled fuel evaporate

before starting engine.

Figure 4-5. Adding Fuel

Acceptable Oil

Level Range

Set-up

Water Pump 13

4.4 — CONNECT SUCTION AND

D

ISCHARGE HOSE

1. Attach and thread a gasket and hose barb to each of

the threaded flanges using a hose nut (Figure 4-6).

Figure 4-6. Attach Gasket and Hose Barb

2. Attach the flexible blue discharge hose to the blue

colored flange by sliding the hose over the barb and

securing with a hose clamp.

3. Attach the green suction hose to the green colored

flange by sliding the hose over the barb and securing

with a hose clamp (Figure 4-7).

Figure 4-7. Attach Hoses

4. Attach the filter to the suction hose by inserting the

barb end into the suction hose and securing with a

hose clamp. Then attach the filter end (Figure 4-8).

Figure 4-8. Attach Filter

4.5 — PRIME THE UNIT

Remove the Easy Prime cap from the pump and com-

pletely fill the pump chamber with clean water. Tighten

the cap. DO NOT over tighten.

14 Water Pump

This page intentionally left blank.

Set-up

Water Pump 15

5.1 — OPERATION

If you have any problems operating your water pump,

please call Generac customer service at

1-888-436-3722.

5.2 — WATER PUMP LOCATION

5.2.1 — Clearances and Air Movement

Running engine gives off carbon monoxide,

an odorless, colorless, poisonous gas.

Breathing carbon monoxide can cause head-

ache, fatigue, dizziness, vomiting, confusion,

seizures, nausea, fainting or death. For more

information, reference the CO warnings in the

“Safety” section.

Place water pump outdoors in an area that will not accu-

mulate deadly exhaust gas. NEVER place water pump

where exhaust gas could accumulate and enter inside or

be drawn into a potentially occupied building. Ensure

exhaust gas is kept away from any windows, doors, ven-

tilation intakes, or other openings that can allow exhaust

gas to collect in a confined area. Prevailing winds and air

currents should be taken into consideration when posi-

tioning water pump (Figure 5-1).

• Operate water pump ONLY outdoors.

• Keep exhaust gas from entering a confined area

through windows, doors, ventilation intakes, or other

openings.

• NEVER start or run engine indoors, in a vehicle or in

an enclosed area, EVEN if windows and doors are

open.

Exhaust heat/gases can ignite combus-

tibles, structures or damage fuel tank

causing a fire.

• Keep at least 5 ft. (152 cm) clearance on all sides of

water pump including overhead.

Figure 5-1. Building Clearances

Place the pump on a level surface free from any obstruc-

tions or potential hazards. The pump should be placed

close to the water level to ensure maximum performance.

Pump output will be affected by the type, length, and size

of the suction and discharge hoses. The pumping height,

total head, is the distance from the water level to the

point of discharge (Figure 5-2). As this distance

increases, the pump output decreases. The discharge

capacity is greater than the suction capacity, therefore it

is important to keep the suction head less than the dis-

charge head. The time required to draw water from the

source to the pump (self-priming time) can be decreased

by minimizing the suction head.

Figure 5-2. Pump Output

5 Foot Minimum

Section 5 Operation

Operation

16 Water Pump

Route the suction hose so that the filter is immersed

completely in the water supply source. DO NOT operate

pump without the filter fully immersed. DO NOT operate

the pump without the filter attached to the hose. Secure

the suction hose to keep it from moving once the Water

Pump is turned on.

Route the discharge hose to the desired location. Secure

the discharge hose to keep it from moving once the

Water Pump is turned on.

5.3 — CHECKLIST BEFORE STARTING

E

NGINE

1. Be sure to read and understand the “Safety” section

and “Operation” section before using water pump.

2. Check that the oil is at the full mark on the dipstick,

and that fuel has been added to the fuel tank.

3. Review the unit’s assembly and ensure fitting are

properly secured and make sure there are no kinks,

cuts, or damage to hoses.

4. Confirm unit is secure on level ground and surround-

ing work area is clear.

NOTE: For the ST20K model, pumping water with sol-

ids larger than .25" can damage the pump and void

the warranty.

5.4 — HOW TO START YOUR WATER PUMP

NOTE: DO NOT run the pump without the unit primed

and suction hose in the water. Damage to equipment

resulting from failure to follow this instruction will

void warranty.

5.4.1 — Starting the CW15 Water Pump

1. Flip engine switch (A) to the ON position (Figure 5-3).

2. Move choke lever (B) to CHOKE position.

A. For a warm engine, be sure the choke lever is in

the RUN position.

3. Secure unit from movement when pulling starter han-

dle (C).

Starter cord kickback (rapid retraction) can

result in bodily injury. Broken bones, frac-

tures, bruises, or sprains could result.

4. When starting the engine, grasp starter grip handle

and pull slowly until you feel some resistance. Then

pull rapidly to start engine.

5. Return starter grip handle slowly. DO NOT let rope

“snap back” against starter.

6. When engine starts, slowly move choke lever to RUN

position as engine warms. If engine falters, move

choke lever to CHOKE position, then back to RUN

position.

7. If engine fails to start after five (5) pulls, move choke

lever to RUN position, and repeat steps 4 through 7.

Figure 5-3. Start the CW15 Water Pump

5.4.2 — Starting the ST20 Water Pump

1. Move fuel valve lever (A) to ON position (Figure 5-4).

2. Move choke lever (B) to CHOKE position.

A. For a warm engine, be sure the choke lever is in

the RUN position.

Figure 5-4. Start the ST20 Water Pump

3. Move throttle control lever (C) to “High” (Rabbit) posi-

tion (Figure 5-6).

4. Turn the engine switch (D) to ON position

(Figure 5-5).

5. Secure unit from movement when pulling starter han-

dle (E) (Figure 5-5).

B

A

C

ACB

D

La page charge ...

Generac 6821 Manuel utilisateur

Generac 6821 Manuel utilisateur

dans d''autres langues

Documents connexes