Huawei B882-66 Le manuel du propriétaire

Taper
Le manuel du propriétaire
4G LTE Huawei B882 Turbo Hub
Getting Started Guide
1
Thank You for Purchasing the Turbo Hub!
Before You Begin
What’s in the Box :
1.
Turbo Hub
2.
Power adapter
3.
1 Ethernet cable (Yellow)
4.
1 Telephone cable
5.
Getting Started Guide
6.
Safety Information Guide
7.
Warranty Information Guide
If anything is missing or damaged, return the entire package to your point of
purchase.
2
1 Getting Started: Setting up Your
Turbo Hub
Follow these simple steps to setup your Turbo Hub.
Place the Turbo Hub at an indoor open area or close to a window if possible.
Obstructions such as concrete or wooden walls may affect the transmission of
wireless signals.
Keep the Turbo Hub away from the household electrical appliances that produce
strong electric or magnetic fields, such as microwaves, refrigerators, or satellite
dish antennas.
Step 1
Insert SIM card into the Turbo Hub’s SIM Card Slot.
If your SIM card was not activated and inserted into your Turbo Hub at your point
of purchase, please call Bell customer service at 1-800-667-0123 to activate it now.
Before removing the SIM card, ensure that Turbo Hub is powered off and
disconnected from the power outlet.
3
Step 2
Connect the power adapter to the power port and plug into the wall
socket.
The Turbo Hub will power on automatically.
4
2 Getting Started: Setting up an
Internet Connection
Connecting your devices (computer, laptop, tablet, etc.) to the Internet
You are able to connect to the Internet via a wired or wireless (Wi-Fi) connection.
Follow the instructions below to set up your connection of choice.
Wired Connection With an Ethernet Cable
Step 1
Connect the Yellow Ethernet cable provided to one of the 3 LAN ports
and connect the other end to your computer.
Step 2
Wait approximately 30 - 60 seconds for the connection to establish. Check
the indicators on the front panel of your Turbo Hub. If they are lit as
outlined you are ready to use the internet with your new Turbo Hub!
Do not connect the Yellow Ethernet cable to the WAN port that is closest to the
right hand side of the device.
5
Power
Solid White: the Turbo Hub is powered on.
Wireless Signal
indicator
Solid Blue or Cyan: the Turbo Hub is registered
with the wireless network.
If this indicator is red and blinking, power off the
Turbo Hub and ensure your SIM card is inserted
correctly.
If this continues after turning the Turbo Hub on
again, please contact Bell customer service at 1-
800-667-0123 to ensure your SIM card is
activated.
Wireless Dial-up
indicator
Solid: the Turbo Hub is connected to the wireless
network.
If this indicator is blinking continuously, power
off the Turbo Hub for 2 minutes and try again.
/ /
LAN indicators
Solid: 1, 2 or 3 will be lit depending on which
LAN port you are connected to.
Blinking: data is transferring.
6
Wireless (Wi-Fi) Connection
Follow these simple steps to connect up to 32 Wi-Fi enabled devices to the Internet
through your Turbo Hub:
Step 1
Ensure that
on the front panel is solid and Wi-Fi is enabled on your
device (computer, laptop, tablet, etc.).
Step 2
From your device, scan for wireless networks in your area. Connect to the
network name that matches the Wi-Fi Name (SSID) found on the Wireless
Security Sticker.
Step 3
When prompted for your wireless security settings, enter the Wi-Fi Password
listed on the Wireless Security Sticker (Wi-Fi Password is case sensitive).
Step 4
Wait approximately 30 seconds for the connection to establish. Your Wi-Fi
enabled device will notify you when it is connected.
Step 5
You may connect up to 32 Wi-Fi enabled devices. Repeat steps 1 through 4.
The Wi-Fi Name (SSID) and Wi-Fi Password (WIFI KEY) are printed on the
Wireless Security Sticker located on the bottom of your Turbo Hub.
To protect your wireless network from unauthorized access, change the Wi-Fi
Name (SSID) and Wi-Fi Password (WIFI KEY)
at regular intervals. For details, see
the online help information on the web user interface.
If you are using Windows Vista or later, you can press the WPS button on the top of
your Turbo Hub for 6 seconds in lieu of entering the Wi-Fi Password.
7
8
3 Getting Started: Setting up Your
Phone
Follow these simple steps to connect a Phone to your Turbo Hub.
Step 1
For voice calls, connect a standard telephone to the Telephone Port using
a RJ-11 cable (you will require a voice plan in addition to a data plan
to use this feature).
Step 2
Check the indicators on the front panel of your Turbo Hub. At minimum the
indicators must be lit as outlined.
You are ready to make your first phone call on your new Turbo Hub! Refer to the
section Using your Turbo Hubs Phone Featuresfor more help on using a phone
with your Turbo Hub.
If the Turbo Hub is to be connected to the existing wall outlet telephone wiring, the
existing wiring MUST first be disconnected from any outside landline telephone
network. Not disconnecting from any outside landline telephone network will cause
excessive heat or even damage the Turbo Hub.
9
Radio signals can interfere with the telephone call connection and quality. To
eliminate the risk of possible interference, place the telephone at least 1 meter
away from the Turbo Hub.
The 4G LTE Turbo Hub voice does not support:
Fax service
Internet dial-up service
Credit card machines
Home security systems
Medical alert systems
Rotary or pulse-dialing telephones
Voice or data service in the event of a power outage
Receiving collect calls
10
Power
Solid White: the Turbo Hub is powered on.
Wireless Signal
indicator
Solid Blue or Cyan: the Turbo Hub is registered
with the wireless network.
If this indicator is red and blinking, power off the
Turbo Hub and ensure your SIM card is inserted
correctly.
If this continues after turning the Turbo Hub on
again, please contact Bell Client Care at 1-800-
667-0123 to ensure your SIM card is activated.
Call status
indicator
Not lit: solid white when you are on a call.
This indicator will blink when you are receiving a
call in addition to your phone ringing.
11
4 Using Your Turbo Hubs Phone
Features
The Turbo Hub offers the ability to make calls via your wireless service. Please
familiarize yourself with the Turbo Hubs calling features below. (Instructions may vary
depending on the telephone model and for cordless handsets)
Forwarding a Call
Forward All Incoming Calls
All your incoming calls will be forwarded to another number.
To activate:
Step 1
Dial *21* before the area code and number you want to forward your calls
to, followed by # e.g. *21*4161234567#.
Step 2
You will hear a tone that indicates call forwarding has been activated.
To deactivate it:
Dial #21#. When you hear a tone hang up, Call Forwarding has been cancelled.
Forwarding Calls When Busy
Only when you are on the phone and the line is busy, your incoming calls will get
forwarded.
To activate:
Step 1
Dial *67* before the area code and number you want to forward your calls
to, followed by # e.g. *67*4161234567#.
Step 2
You will hear a tone that indicates call forwarding has been activated.
To deactivate it:
Dial #67#. When you hear a tone hang up, Call Forwarding has been cancelled.
Call Forward No Answer
Only if your phone rings and is not answered, your incoming calls will get forwarded.
To activate:
Step 1
Dial *61* before the area code and number you want to forward your calls
to, followed by # e.g. *61*4161234567#.
Step 2
You will hear a tone that indicates call forwarding has been activated.
To deactivate it:
Dial #61#. When you hear a tone hang up, Call Forwarding has been cancelled.
12
Making a Conference Call
You can conference a maximum of three people. The first call can be incoming or
outgoing, but the second call must be initiated by you.
To make a conference call:
Step 1
During a call, ask the recipient to hold, then press the Flash/Talk key (varies
by telephone model).
Step 2
Dial the next number.
Step 3
When the call is answered, press the Flash/Talk key to connect both calls.
Your conference call is set up.
To disconnect one of the participants:
During the call, press the Flash/Talk key (varies by telephone model). The participant
who was last to join the call is disconnected.
To end the conference call:
Hang up or Press the End key to end the call. Your conference call ends.
Call Waiting
When another call comes in, Call Waiting alerts you with two fast beeps. You either
accept the second incoming call or let it to go straight to voice mail. Either way, you
never miss a call.
Call Waiting works with Call Display, so you can see who is calling before deciding to
interrupt your first call.
You can disable Call Waiting for those calls you don't want interrupted.
To activate call waiting:
Dial *43# and hang up after you hear a tone indicating Call Waiting has been
activated.
To deactivate call waiting:
Dial #43# and hang up after you hear a tone indicating Call Waiting has been
deactivated.
To accept a call waiting:
Press the Hang up/Hook down (varies by phone model) during the call.
To alternate between calls:
Press the Hang up/Hook down (varies by phone model) during the call.
13
Caller ID
Caller ID shows the phone numbers of your incoming calls so you have the flexibility
to choose whether to answer the call. When used with Call Waiting, you see
incoming phone numbers even if you are on another call.
Using outbound Caller ID, you can choose to block your number as "Restricted".
To block your caller ID on an outbound call:
Dial #31# and hang up after you hear a tone.
To unblock your caller ID on an outbound call:
Dial *31# and hang up after you hear a tone.
Checking Your Voice Mail
You can check your voice mail from your telephone or another phone.
From your telephone:
Step 1
Dial your Turbo Hub number. A message tells you if you have any voice mail
messages.
Step 2
If you have messages, follow the prompts.
From another phone:
Step 1
Dial your Turbo Hub number. Your voice mail greeting plays.
Step 2
During your voice mail greeting, press the # key.
Step 3
Type your password and follow the prompts.
Bell Mobility Customer Service
Dial 611.
Emergency Calls
Dial 911.
911 services are supported similar to that of other wireless devices, your location
information may not be available to the operator. Be prepared to provide the
location of the emergency.
In the event of a power outage, voice service including 911 will not function.
14
5 First Time Quick Setup Wizard
The first time you go to the Web user interface site, you will be presented with the
opportunity to quickly setup your Turbo Hub credentials via the Quick Setup Wizard.
After completing the Quick Setup Wizard, you can choose Settings > Quick Setup to
access this setup again.
Step 1
Launch a web browser, and enter http://huawei.turbohub or
http://192.168.1.1 in the address bar.
Step 2
Enter the website password, and log in to the web user interface. The
default password is admin. You must choose a new password for the web
user interface to continue. Once your password has been changed, you will
be redirected to the Quick Setup Wizard page shown below.
Step 3
The default profile should have Connection Channel set to Wireless only.
Click Next to continue.
Step 4
The Profile list should be set to BELL APN. Click Next to continue.
Step 5
Configure WLAN basic settings in the page.
15
SSID Name: The SSID is the name of your wireless network. Use a
unique name to identify your wireless network so that you can easily
connect from your wireless clients.
SSID Broadcast: Select Enable to broadcast the SSID of your Turbo
Hub, or select Disable to hide. If the SSID Broadcast option is disabled,
other people will not be able scan and detect your
Turbo Hub’s SSID.
Click Next to continue.
Step 6
Configure WLAN security settings.
Setting a strong wireless security level (such as WPA2-PSK AES) can
prevent unauthorized access to your wireless network. Please enter the
Security Key that you wish to use, or leave this field unchanged to use the
default Security Key.
Click Next to continue.
Step 7
Review your settings then click Finish to save configuration.
16
6 Changing Your Turbo Hub Settings
You can configure and manage the Turbo Hub settings using the web user interface.
Step 1
Launch a web browser, and enter http://huawei.turbohub or
http://192.168.1.1 in the address bar.
Step 2
Enter the password, and log in to the web user interface. The default
password is admin.
To protect your Turbo Hub, only one user can log in to the web user interface at a
time.
To protect your account, change the default login password to a highly secure
password. For details, see the online help information on the web user interface.
17
7 Getting to Know Your Turbo Hub
Appearance
1
Power button
2
Power port
3
Telephone port
4
LAN ports
5
WAN port
6
Wi-Fi/WPS button
7
Dial-up button (used only
when connection mode is set
to manual)
8
SIM card slot
1
Power indicator
2
Network status indicator
3
Wi-Fi/WPS indicator
4
SMS indicator
5
Call status indicator
6
Wireless dialing indicator
7
LAN indicators
8
Ethernet dialing indicator
18
Indicators
The front panel of your Turbo Hub provides simple and intuitive indicators so that you
can easily learn the Turbo Hub’s status by observing the indicator lights.
Indicator Status
Power indicator
On: Turbo Hub powered on.
Off: Turbo Hub powered off.
Network status indicator
Fast red blinking: SIM card unavailable (SIM
card not installed or malfunctioning, or PIN
code not verified).
Steady blue: Turbo Hub registered with 4G
network.
Steady cyan: Turbo Hub registered with LTE
network.
Off: no signal received.
The Turbo Hub provides Data and Voice services on
the Bell 4G network and will not support wireless
services outside of Bell coverage area.
This indicator does not represent the actual wireless
signal strength of Turbo Hub. Login to the Web User
Interface to view actual signal strength.
Wi-Fi/WPS indicator
Steady on: Wi-Fi turned on or data transfer in
progress.
Blinking: WPS connection being set up.
Off: Wi-Fi turned off.
SMS/Voicemail indicator
Steady on: inbox full.
Blinking: new messages.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Huawei B882-66 Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues