Smeg SI1M7733B Manuel utilisateur

SI1M7733B

User Manual

Hob

Notice d'utili‐

sation

Table de

cuisson

Benutzerin‐

formation

Kochfeld

CONTENTS

Safety information 2

Safety instructions 4

Installation 6

Product description 8

Daily use 10

Hints and tips 15

Care and cleaning 18

Troubleshooting 18

Technical data 20

Energy efficiency 21

CUSTOMER CARE AND SERVICE

Always use original spare parts.

When contacting our Authorised Service Centre, ensure that you have the following

data available: Model, Serial Number.

The information can be found on the rating plate.

Warning / Caution-Safety information

General information and tips

Environmental information

VISIT OUR WEBSITE TO:

Get usage advice, brochures, trouble shooter, service and repair information:

www.smeg.com/services/customer-service

Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance, carefully

read the supplied instructions. The manufacturer is not

responsible for any injuries or damages that are the result of

incorrect installation or usage. Always keep the instructions

in a safe and accessible location for future reference.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

the use of the appliance in a safe way and understand the

hazards involved.

2

• Children between 3 and 8 years of age and persons with

very extensive and complex disabilities shall be kept away

unless continuously supervised.

• Children of less than 3 years of age should be kept away

unless continuously supervised.

• Do not let children play with the appliance.

• Keep all packaging away from children and dispose of it

appropriately.

• Keep children and pets away from the appliance when it

operates or when it cools down. Accessible parts are hot.

• If the appliance has a child safety device, it should be

activated.

• Children shall not carry out cleaning and user maintenance

of the appliance without supervision.

General Safety

• WARNING: The appliance and its accessible parts

become hot during use. Care should be taken to avoid

touching heating elements.

• Do not operate the appliance by means of an external

timer or separate remote-control system.

• WARNING: Unattended cooking on a hob with fat or oil

can be dangerous and may result in fire.

• NEVER try to extinguish a fire with water, but switch off the

appliance and then cover flame e.g. with a lid or a fire

blanket.

• CAUTION: The cooking process has to be supervised. A

short term cooking process has to be supervised

continuously.

• WARNING: Danger of fire: Do not store items on the

cooking surfaces.

• Metallic objects such as knives, forks, spoons and lids

should not be placed on the hob surface since they can get

hot.

• Do not use a steam cleaner to clean the appliance.

• After use, switch off the hob element by its control and do

not rely on the pan detector.

3

• If the glass ceramic surface / glass surface is cracked,

switch off the appliance and unplug it from the mains. In

case the appliance is connected to the mains directly using

junction box, remove the fuse to disconnect the appliance

from power supply. In either case contact the Authorised

Service Centre.

• If the supply cord is damaged, it must be replaced by the

manufacturer, an authorized Service or similarly qualified

persons in order to avoid a hazard.

• WARNING: Use only hob guards designed by the

manufacturer of the cooking appliance or indicated by the

manufacturer of the appliance in the instructions for use as

suitable or hob guards incorporated in the appliance. The

use of inappropriate guards can cause accidents.

SAFETY INSTRUCTIONS

Installation

WARNING! Only a qualified

person must install this

appliance.

WARNING! Risk of injury or

damage to the appliance.

• Remove all the packaging.

• Do not install or use a damaged

appliance.

• Follow the installation instructions

supplied with the appliance.

• Keep the minimum distance from other

appliances and units.

• Always take care when moving the

appliance as it is heavy. Always use

safety gloves and enclosed footwear.

• Seal the cut surfaces with a sealant to

prevent moisture to cause swelling.

• Protect the bottom of the appliance

from steam and moisture.

• Do not install the appliance adjacent to

a door or under a window. This

prevents hot cookware falling from the

appliance when the door or the window

is opened.

• Each appliance has cooling fans on the

bottom.

• If the appliance is installed above a

drawer:

– Do not store any small pieces or

sheets of paper that could be pulled

in, as they can damage the cooling

fans or impair the cooling system.

– Keep a distance of minimum 2 cm

between the bottom of the

appliance and parts stored in the

drawer.

Electrical Connection

WARNING! Risk of fire and

electric shock.

• All electrical connections should be

made by a qualified electrician.

• The appliance must be earthed.

• Before carrying out any operation make

sure that the appliance is disconnected

from the power supply.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Make sure the appliance is installed

correctly. Loose and incorrect electricity

mains cable or plug (if applicable) can

make the terminal become too hot.

4

• Use the correct electricity mains cable.

• Do not let the electricity mains cable

tangle.

• Make sure that a shock protection is

installed.

• Use the strain relief clamp on the cable.

• Make sure the mains cable or plug (if

applicable) does not touch the hot

appliance or hot cookware, when you

connect the appliance to the near

sockets.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

mains plug (if applicable) or to the

mains cable. Contact our Authorised

Service Centre or an electrician to

change a damaged mains cable.

• The shock protection of live and

insulated parts must be fastened in

such a way that it cannot be removed

without tools.

• Connect the mains plug to the mains

socket only at the end of the

installation. Make sure that there is

access to the mains plug after the

installation.

• If the mains socket is loose, do not

connect the mains plug.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• Use only correct isolation devices: line

protecting cut-outs, fuses (screw type

fuses removed from the holder), earth

leakage trips and contactors.

• The electrical installation must have an

isolation device which lets you

disconnect the appliance from the

mains at all poles. The isolation device

must have a contact opening width of

minimum 3 mm.

Use

WARNING! Risk of injury,

burns and electric shock.

• Remove all the packaging, labelling

and protective film (if applicable) before

first use.

• Use this appliance in a household

environment.

• Do not change the specification of this

appliance.

• Make sure that the ventilation openings

are not blocked.

• Do not let the appliance stay

unattended during operation.

• Set the cooking zone to “off” after each

use.

• Do not rely on the pan detector.

• Do not put cutlery or saucepan lids on

the cooking zones. They can become

hot.

• Do not operate the appliance with wet

hands or when it has contact with

water.

• Do not use the appliance as a work

surface or as a storage surface.

• If the surface of the appliance is

cracked, disconnect immediately the

appliance from the power supply. This

to prevent an electrical shock.

• Users with a pacemaker must keep a

distance of minimum 30 cm from the

induction cooking zones when the

appliance is in operation.

• When you place food into hot oil, it may

splash.

WARNING! Risk of fire and

explosion

• Fats and oil when heated can release

flammable vapours. Keep flames or

heated objects away from fats and oils

when you cook with them.

• The vapours that very hot oil releases

can cause spontaneous combustion.

• Used oil, that can contain food

remnants, can cause fire at a lower

temperature than oil used for the first

time.

• Do not put flammable products or items

that are wet with flammable products

in, near or on the appliance.

WARNING! Risk of damage to

the appliance.

• Do not keep hot cookware on the

control panel.

5

• Do not put a hot pan cover on the glass

surface of the hob.

• Do not let cookware to boil dry.

• Be careful not to let objects or

cookware fall on the appliance. The

surface can be damaged.

• Do not activate the cooking zones with

empty cookware or without cookware.

• Do not put aluminium foil on the

appliance.

• Cookware made of cast iron, aluminium

or with a damaged bottom can cause

scratches on the glass / glass ceramic.

Always lift these objects up when you

have to move them on the cooking

surface.

• This appliance is for cooking purposes

only. It must not be used for other

purposes, for example room heating.

Care and cleaning

• Clean the appliance regularly to

prevent the deterioration of the surface

material.

• Deactivate the appliance and let it cool

down before you clean it.

• Disconnect the appliance from the

electrical supply before maintenance.

• Do not use water spray and steam to

clean the appliance.

• Clean the appliance with a moist soft

cloth. Only use neutral detergents. Do

not use any abrasive products,

abrasive cleaning pads, solvents or

metal objects.

Service

• To repair the appliance contact the

Authorised Service Centre. Use original

spare parts only.

• Concerning the lamp(s) inside this

product and spare part lamps sold

separately: These lamps are intended

to withstand extreme physical

conditions in household appliances,

such as temperature, vibration,

humidity, or are intended to signal

information about the operational status

of the appliance. They are not intended

to be used in other applications and are

not suitable for household room

illumination.

Disposal

WARNING! Risk of injury or

suffocation.

• Contact your municipal authority for

information on how to discard the

appliance correctly.

• Disconnect the appliance from the

mains supply.

• Cut off the mains electrical cable close

to the appliance and dispose of it.

INSTALLATION

WARNING! Refer to Safety

chapters.

Before the installation

Before you install the hob, write down the

information bellow from the rating plate.

The rating plate is on the bottom of the

hob.

Serial number ...........................

Built-in hobs

Only use the built-in hobs after you

assemble the hob into correct built-in units

and work surfaces that align to the

standards.

Connection cable

• The hob is supplied with the connection

cable.

• Replace the damaged mains cable only

with the spare parts cable. Speak to

your local Authorised Service Center.

WARNING! All electrical

connections must be made by

a qualified electrician.

6

CAUTION! Do not drill or

solder the wire ends. This is

strictly forbidden!

CAUTION! Do not connect the

cable without cable end sleeve.

Two-phase connection

1. Remove the cable end sleeve from

black and brown wires.

2. Remove an insulation of the brown

and black cable ends.

3. Apply a new wire end sleeve of 1.5

mm² on each cable end. (special tool

required).

Cable cross section

N

L1

N

L

230V~ 400V 2~N

L2

One-phase connection - 230 V~ Two-phase connection - 400 V 2 ~ N

Green - yellow Green - yellow

N Blue and blue Blue and blue N

L Black and brown Black L1

Brown L2

Assembly

min.

50mm

min.

500mm

R 5mm

min.

55mm

560

+1

mm

490

+1

mm

7

min.

28 mm

min.

12 mm

min. 60mm

If the appliance is installed

above a drawer, the hob

ventilation can warm up the

items stored in the drawer

during the cooking process.

You can instal a separation

panel but it is not mandatory.

PRODUCT DESCRIPTION

Cooking surface layout

1

2

1

Induction cooking zone

2

Control panel

8

Control panel layout

74 52 3

10 9

61

11

8

Use the sensor fields to operate the appliance. The displays, indicators and sounds tell

which functions operate.

Sensor

field

Function Comment

1

ON / OFF To activate and deactivate the hob.

2

Lock / Child Safety De‐

vice

To lock / unlock the control panel.

3

Pause To activate and deactivate the function.

4

MultiZone To activate and deactivate the function.

5

- Heat setting display To show the heat setting.

6

- Timer indicators of

cooking zones

To show for which zone you set the time.

7

- Timer display To show the time in minutes.

8

Auto-Vent To activate and deactivate the manual mode

of the function.

9

- To select the cooking zone.

10

/

- To increase or decrease the time.

11

- Control bar To set a heat setting.

Heat setting displays

Display Description

The cooking zone is deactivated.

-

The cooking zone operates.

Pause operates.

Accelerator operates.

9

Display Description

Power function operates.

+ digit

There is a malfunction.

/ /

Eco-Heat (3-step Residual heat indicator): continue cooking / keep

warm / residual heat.

Lock / Child Safety Device operates.

Incorrect or too small cookware or no cookware on the cooking zone.

Automatic Switch Off operates.

Eco-Heat (3 step Residual heat

indicator)

WARNING! / / There

is a risk of burns from residual

heat. The indicator shows the

level of the residual heat. If a

given zone becomes too hot

the function may lower the heat

setting for neighbouring zones.

The induction cooking zones produce the

heat necessary for the cooking process

directly in the bottom of the cookware. The

glass ceramic is heated by the heat of the

cookware.

DAILY USE

WARNING! Refer to Safety

chapters.

Activating and deactivating

Touch for 1 second to activate or

deactivate the hob.

Automatic Switch Off

The function deactivates the hob

automatically if:

• all cooking zones are deactivated,

• you do not set the heat setting after you

activate the hob,

• you spill something or put something

on the control panel for more than 10

seconds (a pan, a cloth, etc.). An

acoustic signal sounds and the hob

deactivates. Remove the object or

clean the control panel.

• the hob gets too hot (e.g. when a

saucepan boils dry). Let the cooking

zone cool down before you use the hob

again.

• you use incorrect cookware. The

symbol comes on and the cooking

zone deactivates automatically after 2

minutes.

• you do not deactivate a cooking zone

or change the heat setting. After some

time comes on and the hob

deactivates.

The relation between the heat setting

and the time after which the hob

deactivates:

Heat setting The hob deacti‐

vates after

, 1 - 3

6 hours

10

Heat setting The hob deacti‐

vates after

4 - 7 5 hours

8 - 9 4 hours

10 - 14 1.5 hour

The heat setting

To set or change the heat setting:

Touch the control bar at the correct heat

setting or move your finger along the

control bar until you reach the correct heat

setting.

Using the cooking zones

Place the cookware in the centre of the

selected zone. Induction cooking zones

adapt to the dimension of the bottom of

the cookware automatically.

You can cook with large cookware placed

on two cooking zones at the same time.

The cookware must cover the centres of

both zones. Correct cookware positions:

Incorrect cookware positions:

MultiZone

The function operates when the

pot covers the centres of the

two zones.

This function connects two left side

cooking zones and they operate as one.

First set the heat setting for one of the left

side cooking zones.

To activate the function: touch . To set

or change the heat setting touch one of

the control sensors.

To deactivate the function: touch . The

cooking zones operate independently.

Accelerator

Activate this function to get a desired heat

setting in a shorter time. When it is on, the

zone operates on the highest setting in the

beginning and then continues to cook at

the desired heating setting.

To activate the function the

cooking zone must be cold.

To activate the function for a cooking

zone: touch the end of the control bar on

the right ( comes on). Immediately

touch a desired heat setting. After 3

seconds comes on.

To deactivate the function: change the

heat setting.

Power function

This function makes more power available

to the induction cooking zones. The

function can be activated for the induction

cooking zone only for a limited period of

11

time. After this time the induction cooking

zone automatically sets back to the

highest heat setting.

Refer to “Technical information”

chapter.

To activate the function for a cooking

zone: touch the end of the control bar on

the right. comes on.

To deactivate the function: change the

heat setting.

Timer

Count Down Timer

You can use this function to set how long

the cooking zone should operate for a

single cooking session.

First set the heat setting for the cooking

zone then set the function.

To set the cooking zone: touch

again and again until the indicator of a

necessary cooking zone comes on.

To activate the function: touch of the

timer to set the time (00 - 99 minutes).

When the indicator of the cooking zone

starts to flash slowly the time counts

down.

To see the remaining time: set the

cooking zone with

. The indicator of

the cooking zone starts to flash quickly.

The display shows the remaining time.

To change the time: set the cooking zone

with . Touch or .

To deactivate the function: set the

cooking zone with

and touch .

The remaining time counts back to 00.

The indicator of the cooking zone goes

out.

When the time comes to an

end, the sound operates and

00 flashes. The cooking zone

deactivates.

To stop the sound: touch .

CountUp Timer (The count up timer)

You can use this function to monitor how

long the cooking zone operates.

To set the cooking zone: touch

again and again until the indicator of a

necessary cooking zone comes on.

To activate the function: touch of the

timer. comes on. When the indicator of

the cooking zone starts to flash slowly the

time counts up. The display switches

between and counted time (minutes).

To see how long the cooking zone

operates: set the cooking zone with

. The indicator of the cooking zone

starts to flash quickly. The display shows

how long the zone operates.

To deactivate the function: set the

cooking zone with and touch or

. The indicator of the cooking zone goes

out.

Minute Minder

You can use this function as a Minute

Minder when the hob is activated and the

cooking zones do not operate. The heat

setting display shows .

To activate the function: touch

.

Touch or of the timer to set the time.

When the time comes to an end, the

sound operates and 00 flashes.

To stop the sound: touch .

The function has no effect on

the operation of the cooking

zones.

Pause

This function sets all cooking zones that

operate to the lowest heat setting.

When the function operates, all other

symbols on the control panels are locked.

The function does not stop the timer

functions.

Touch

to activate the function.

12

comes on. The heat setting is lowered

to 1.

To deactivate the function, touch .

The previous heat setting comes on.

Lock

You can lock the control panel while

cooking zones operate. It prevents an

accidental change of the heat setting.

Set the heat setting first.

To activate the function: touch

.

comes on for 4 seconds. The Timer stays

on.

To deactivate the function: touch .

The previous heat setting comes on.

When you deactivate the hob,

you also deactivate this

function.

Child Safety Device

This function prevents an accidental

operation of the hob.

To activate the function: activate the hob

with . Do not set the heat setting. Touch

for 4 seconds. comes on.

Deactivate the hob with .

To deactivate the function: activate the

hob with

. Do not set the heat setting.

Touch for 4 seconds. comes on.

Deactivate the hob with .

To override the function for only one

cooking time: activate the hob with

.

comes on. Touch for 4 seconds.

Set the heat setting in 10 seconds. You

can operate the hob. When you deactivate

the hob with the function operates

again.

OffSound Control (Deactivating

and activating the sounds)

Deactivate the hob. Touch for 3

seconds. The display comes on and goes

out. Touch for 3 seconds. or

comes on. Touch of the timer to

choose one of the following:

• - the sounds are off

• - the sounds are on

To confirm your selection wait until the

hob deactivates automatically.

When the function is set to you can

hear the sounds only when:

• you touch

• Minute Minder comes down

• Count Down Timer comes down

• you put something on the control panel.

Power limitation

Originally the hob is at its highest possible

power level.

To decrease or increase the power

level:

1. Deactivate the hob.

2. Touch for 3 seconds. The display

comes on and goes off.

3. Touch for 3 seconds. or

comes on.

4. Touch . P 72 comes on.

5. Touch

/ of the Timer to set the

power level.

Power levels

Refer to “Technical information” chapter.

• P 72 — 7200 W

• P 15 — 1500 W

• P 20 — 2000 W

• P 25 — 2500 W

• P 30 — 3000 W

• P 35 — 3500 W

• P 40 — 4000 W

• P 45 — 4500 W

• P 50 — 5000 W

• P 60 — 6000 W

CAUTION! Make sure that the

selected power fits to the

house installation fuses.

13

Eco-Logic

• Cooking zones are grouped according

to the location and number of the

phases in the hob. See the illustration.

• Each phase has a maximum electricity

loading of 3600 W.

• The function divides the power

between cooking zones connected to

the same phase.

• The function activates when the total

electricity loading of the cooking zones

connected to a single phase exceeds

3600 W.

• The function decreases the power to

the other cooking zones connected to

the same phase.

• The last selected heat setting has the

priority. As a consequence, the heat

setting of the other zones may

automatically reduce. The previous

heat setting, and the new one adjusted

by the function, alternate on the display

for 60 seconds.

When you set the Power limitation

function to 6.0 kW or less, power of the

hob is divided between all cooking zones.

When you set the Power limitation

function to more than 6.0 kW, power of

the hob is divided between two cooking

zones in a pair.

Auto-Vent

It is an advanced automatic function which

connects the hob to an Auto-Vent hood.

Both the hob and the hood have an

infrared signal communicator. Speed of

the fan is defined automatically on basis of

mode setting and temperature of the

hottest cookware on the hob. You can

also operate the fan from the hob

manually.

For most of the hoods the

remote system is originally

deactivated. Activate it before

you use the function. For more

information refer to hood user

manual.

Operating the function automatically

To operate the function automatically set

the automatic mode to H1 – H6. The hob

is originally set to H5. The hood reacts

whenever you operate the hob. The hob

recognizes temperature of the cookware

automatically and adjusts the speed of the

fan.

Automatic modes

Auto‐

matic

light

Boil‐

ing

1)

Fry‐

ing

2)

Mode

H0

Off Off Off

Mode

H1

On Off Off

14

Auto‐

matic

light

Boil‐

ing

1)

Fry‐

ing

2)

Mode

H2

3)

On Fan

speed

1

Fan

speed

1

Mode

H3

On Off Fan

speed

1

Mode

H4

On Fan

speed

1

Fan

speed

1

Mode

H5

On Fan

speed

1

Fan

speed

2

Mode

H6

On Fan

speed

2

Fan

speed

3

1)

The hob detects the boiling process and activates

fan speed in accordance with automatic mode.

2)

The hob detects the frying process and activates

fan speed in accordance with automatic mode.

3)

This mode activates the fan and the light and does

not rely on the temperature.

Changing the automatic mode

1. Deactivate the appliance.

2. Touch for 3 seconds. The display

comes on and goes off.

3. Touch for 3 seconds.

4. Touch

a few times until

comes on.

5. Touch of the Timer to select an

automatic mode.

To operate the hood directly on

the hood panel deactivate the

automatic mode of the function.

When you finish cooking and

deactivate the hob, the hood

fan may still operate for a

certain period of time. After that

time the system deactivates the

fan automatically and prevents

you from accidental activation

of the fan for the next 30

seconds.

Operating the fan speed manually

You can also operate the function

manually. To do that touch when the

hob is active. This deactivates automatic

operation of the function and allows you to

change the fan speed manually. When

you press you raise the fan speed by

one. When you reach an intensive level

and press again you will set fan speed

to 0 which deactivates the hood fan. To

start the fan again with fan speed 1 touch

.

To activate automatic operation

of the function, deactivate the

hob and activate it again.

Activating the light

You can set the hob to activate the light

automatically whenever you activate the

hob. To do so set the automatic mode to

H1 – H6.

The light on the hood

deactivates 2 minutes after

deactivating the hob.

HINTS AND TIPS

WARNING! Refer to Safety

chapters.

15

Cookware

For induction cooking zones a

strong electro-magnetic field

creates the heat in the

cookware very quickly.

Use the induction cooking

zones with suitable cookware.

Cookware material

• correct: cast iron, steel, enamelled

steel, stainless steel, multi-layer bottom

(with a correct marking from a

manufacturer).

• not correct: aluminium, copper, brass,

glass, ceramic, porcelain.

Cookware is suitable for an induction

hob if:

• water boils very quickly on a zone set

to the highest heat setting.

• a magnet pulls on to the bottom of the

cookware.

The bottom of the cookware

must be as thick and flat as

possible.

Ensure pan bases are clean

and dry before placing on the

hob surface.

Cookware dimensions

Induction cooking zones adapt to the

dimension of the bottom of the cookware

automatically.

The cooking zone efficiency is related to

the diameter of the cookware. The

cookware with a diameter smaller than the

minimum receives only a part of the power

generated by the cooking zone.

Refer to "Technical data".

The noises during operation

If you can hear:

• crack noise: cookware is made of

different materials (sandwich

construction).

• whistle sound: you use the cooking

zone with high power level and the

cookware is made of different materials

(sandwich construction).

• humming: you use high power level.

• clicking: electric switching occurs.

• hissing, buzzing: the fan operates.

The noises are normal and do not refer

to hob malfunction.

Eco-Off (Eco Timer)

To save energy, the heater of the cooking

zone deactivates before the count down

timer sounds. The difference in the

operation time depends on the heat

setting level and the length of the cooking

operation.

Examples of cooking

applications

The correlation between the heat setting

of a zone and its consumption of power is

not linear. When you increase the heat

setting, it is not proportional to the

increase of the consumption of power. It

means that a cooking zone with the

medium heat setting uses less than a half

of its power.

The data in the table is for

guidance only.

Heat setting Use to: Time

(min)

Hints

- 1

Keep cooked food warm. as

nec‐

essary

Put a lid on the cookware.

16

Heat setting Use to: Time

(min)

Hints

1 - 3 Hollandaise sauce, melt: but‐

ter, chocolate, gelatine.

5 - 25 Mix from time to time.

1 - 3 Solidify: fluffy omelettes, baked

eggs.

10 -

40

Cook with a lid on.

3 - 5 Simmer rice and milkbased

dishes, heat up ready-cooked

meals.

25 -

50

Add at least twice as much liq‐

uid as rice, mix milk dishes

halfway through the proce‐

dure.

5 - 7 Steam vegetables, fish, meat. 20 -

45

Add a couple of tablespoons

of liquid.

7 - 9 Steam potatoes. 20 -

60

Use max. ¼ l of water for 750

g of potatoes.

7 - 9 Cook larger quantities of food,

stews and soups.

60 -

150

Up to 3 l of liquid plus ingredi‐

ents.

9 - 12 Gentle fry: escalope, veal cor‐

don bleu, cutlets, rissoles,

sausages, liver, roux, eggs,

pancakes, doughnuts.

as

nec‐

essary

Turn halfway through.

12 - 13 Heavy fry, hash browns, loin

steaks, steaks.

5 - 15 Turn halfway through.

14 Boil water, cook pasta, sear meat (goulash, pot roast), deep-fry chips.

Boil large quantities of water. Power function is activated.

Hints and Tips for Auto-Vent

When you operate the hob with the

function:

• Protect the hood panel from direct

sunlight.

• Do not spot halogen light on the hood

panel.

• Do not cover the hob control panel.

• Do not interrupt the signal between the

hob and the hood (for example with a

hand or a cookware handle). See the

picture.

The hood in the picture is only

exemplary.

17

Other remotely controlled

appliances may block the

signal. Do not use any remotely

controlled appliances at the

time when you use the function

on the hob.

Cooker hoods with the Auto-Vent

function

To find the full range of cooker hoods

which work with this function refer to our

consumer website.

CARE AND CLEANING

WARNING! Refer to Safety

chapters.

General information

• Clean the hob after each use.

• Always use cookware with a clean

base.

• Scratches or dark stains on the surface

have no effect on how the hob

operates.

• Use a special cleaner suitable for the

surface of the hob.

• Use a special scraper for the glass.

Cleaning the hob

• Remove immediately: melted plastic,

plastic foil, sugar and food with sugar. If

not, the dirt can cause damage to the

hob. Take care to avoid burns. Put the

special scraper on the glass surface at

an acute angle and move the blade on

the surface.

• Remove when the hob is sufficiently

cool: limescale rings, water rings, fat

stains, shiny metallic discoloration.

Clean the hob with a moist cloth and

non-abrasive detergent. After cleaning,

wipe the hob dry with a soft cloth.

• Remove shiny metallic

discoloration: use a solution of water

with vinegar and clean the glass

surface with a moist cloth.

TROUBLESHOOTING

WARNING! Refer to Safety

chapters.

What to do if...

Problem Possible cause Remedy

You cannot activate or oper‐

ate the hob.

The hob is not connected to

an electrical supply or it is

connected incorrectly.

Check if the hob is correctly

connected to the electrical

supply. Refer to the connec‐

tion diagram.

The fuse is blown. Make sure that the fuse is

the cause of the malfunc‐

tion. If the fuse is blown

again and again, contact a

qualified electrician.

18

Problem Possible cause Remedy

You do not set the heat set‐

ting for 10 seconds.

Activate the hob again and

set the heat setting in less

than 10 seconds.

You touched 2 or more sen‐

sor fields at the same time.

Touch only one sensor field.

Pause function operates. Refer to "Daily use".

There is water or fat stains

on the control panel.

Clean the control panel.

An acoustic signal sounds

and the hob deactivates.

An acoustic signal sounds

when the hob is deactivated.

You put something on one

or more sensor fields.

Remove the object from the

sensor fields.

The hob deactivates. You put something on the

sensor field .

Remove the object from the

sensor field.

Residual heat indicator does

not come on.

The zone is not hot because

it operated only for a short

time or the sensor is dam‐

aged.

If the zone operated suffi‐

ciently long to be hot, speak

to an Authorised Service

Centre.

Auto-Vent does not work. You covered the control

panel.

Remove the object from the

control panel.

Accelerator does not oper‐

ate.

The zone is hot. Let the zone become suffi‐

ciently cool.

The highest heat setting is

set.

The highest heat setting has

the same power as the func‐

tion.

The heat setting changes

between two levels.

Power management oper‐

ates.

Refer to "Daily use".

The sensor fields become

hot.

The cookware is too large or

you put it too near to the

controls.

Put large cookware on the

rear zones if possible.

There is no sound when you

touch the panel sensor

fields.

The sounds are deactivated. Activate the sounds. Refer

to "Daily use".

comes on.

Automatic Switch Off oper‐

ates.

Deactivate the hob and acti‐

vate it again.

comes on.

Child Safety Device or Lock

operates.

Refer to "Daily use".

comes on.

There is no cookware on the

zone.

Put cookware on the zone.

19

Problem Possible cause Remedy

The cookware is unsuitable. Use suitable cookware. Re‐

fer to "Hints and tips".

The diameter of the bottom

of the cookware is too small

for the zone.

Use cookware with correct

dimensions. Refer to "Tech‐

nical data".

and a number come on.

There is an error in the hob. Deactivate the hob and acti‐

vate it again after 30 sec‐

onds. If comes on again,

disconnect the hob from the

electrical supply. After 30

seconds, connect the hob

again. If the problem contin‐

ues, speak to an Authorised

Service Centre.

You can hear a constant

beep noise.

The electrical connection is

incorrect.

Disconnect the hob from the

electrical supply. Ask a

qualified electrician to check

the installation.

If you cannot find a solution...

If you cannot find a solution to the problem

yourself, contact your dealer or an

Authorised Service Centre. Give the data

from the rating plate. Give also three digit

letter code for the glass ceramic (it is in

the corner of the glass surface) and an

error message that comes on. Make sure,

you operated the hob correctly. If not the

servicing by a service technician or dealer

will not be free of charge, also during the

warranty period. The instructions about

the Service Centre and conditions of

guarantee are in the guarantee booklet.

TECHNICAL DATA

Rating plate

Model SI1M7733B PNC 949 594 451 00

Typ 61 B3A 02 AD 220 - 240 V / 400 V 2N 50 - 60 Hz

Induction 7.2 kW Made in Germany

Ser.Nr. ................. 7.2 kW

SMEG

20

La page charge ...

Smeg SI1M7733B Manuel utilisateur

Smeg SI1M7733B Manuel utilisateur

dans d''autres langues