Sony CDX-F5500 Le manuel du propriétaire

Operating Instructions

Mode d’emploi

Owner’s Record

The model and serial numbers are located on the bottom of the unit.

Record these numbers in the space provided below.

Refer to these numbers whenever you call upon your Sony dealer regarding this product.

Model No. CDX-F5500 Serial No.

CDX-F5500

For installation and connections, see the supplied installation/connections manual.

En ce qui concerne l’installation et les connexions, consulter le manuel

d’installation/raccordement fourni.

3-261-848-11 (1)

US

FR

FM

/

AM

Compact Disc

Player

2

Welcome !

Thank you for purchasing this Sony Compact

Disc Player. You can enjoy its various features

even more with:

• MP3 file playback.

• CD-R/CD-RW which can have a session added

can be played (page 7).

• Discs recorded in Multi Session can be played,

depending on the recording method (page 8).

• Optional CD/MD units (both changers and

players)*

1

.

•ID3 tag*

2

version 1.0, 1.1, 2.2, 2.3 or 2.4

information (displayed when an MP3 file is

played).

• CD TEXT information (displayed when a CD

TEXT disc*

3

is played).

• Supplied controller accessory

Card remote commander RM-X115

• Optional controller accessory

Rotary commander RM-X4S

*1 This unit works with Sony products only.

*2 ID3 tag is an MP3 file that contains information

about album name, artist name, track name, etc.

*3 A CD TEXT disc is an audio CD that includes

information such as the disc name, artist name,

and track names. This information is recorded on

the disc.

Warning

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

p

rotection against harmful interference in a

r

esidential installation. This equipment

generates, uses, and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

r

adio or television reception, which can be

determined by turning the equipment off and on,

the user is encouraged to try to correct the

interference by one or more of the following

measures:

–

Reorient or relocate the receiving antenna.

–

Increase the separation between the equipment

and receiver.

–

Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

–

Consult the dealer or an experienced radio/TV

technician for help.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate this

equipment.

The use of optical instruments with this produc

t

will increase e

y

e hazard.

CAUTION

The “XM Ready” logo indicates that this product

will control a Sony XM tuner module (sold

separately).

Please see your nearest authorized Sony dealer

for details on the XM tuner module.

For instructions on XM tuner operation, please

refer to the XM tuner module’s included

instruction manual.

3

Table of Contents

Location of controls . . . . . . . . . . . . . . . . . . . 4

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Notes on discs . . . . . . . . . . . . . . . . . . . . . . . . 7

About MP3 files . . . . . . . . . . . . . . . . . . . . . . 8

Getting Started

Resetting the unit. . . . . . . . . . . . . . . . . . . . . . 9

Detaching the front panel . . . . . . . . . . . . . . 10

Setting the clock . . . . . . . . . . . . . . . . . . . . . 11

CD Player

CD/MD Unit (optional)

Playing a disc. . . . . . . . . . . . . . . . . . . . . . . . 11

Display items. . . . . . . . . . . . . . . . . . . . . . . . 12

Playing tracks repeatedly

— Repeat Play . . . . . . . . . . . . . . . . . . . . 13

Playing tracks in random order

— Shuffle Play . . . . . . . . . . . . . . . . . . . . 13

Labeling a CD

— Disc Memo*. . . . . . . . . . . . . . . . . . . . 14

Locating a disc by name

— List-up* . . . . . . . . . . . . . . . . . . . . . . . 15

* Functions available with optional CD/MD unit

Radio

Storing stations automatically

— Best Tuning Memory (BTM) . . . . . . 15

Receiving the stored stations . . . . . . . . . . . 16

Storing only the desired stations. . . . . . . . . 16

Storing station names

— Station Memo . . . . . . . . . . . . . . . . . . 17

Tuning in a station through a list

— List-up. . . . . . . . . . . . . . . . . . . . . . . . 18

Other Functions

Using the rotary commander. . . . . . . . . . . . 18

Adjusting the sound characteristics . . . . . . 20

Quickly attenuating the sound . . . . . . . . . . 20

Changing the sound and display settings . . 20

Setting the equalizer (EQ3). . . . . . . . . . . . . 21

Setting the Dynamic Soundstage Organizer

(DSO). . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Additional Information

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 23

Removing the unit. . . . . . . . . . . . . . . . . . . . 24

Specifications . . . . . . . . . . . . . . . . . . . . . . . 25

Troubleshooting . . . . . . . . . . . . . . . . . . . . . 26

Error displays/Messages. . . . . . . . . . . . . . . 27

4

Location of controls

Refer to the pages listed for details.

a DSO button 22

b SOURCE (Power on/Radio/CD/MD)

button

To select the source.

c LIST/CAT*

1

button 14, 15, 18

d Receptor for the card remote

commander

e Display window

f Z (eject) button (located on the front side

of the unit, behind the front panel) 11

g OPEN button 10, 11

h EQ3 button 21, 22

i MODE button

To change operation.

j Volume control dial/Select button

Rotate to:

– Adjust the volume.

– Adjust settings.

Press to:

– Select items.

k DSPL (display mode change) button

11, 12, 14, 21

l SENS button 16

m RESET button (located on the front side of

the unit, behind the front panel) 9

n BTM button

o Number buttons 21

Radio:

To store stations/receive stored stations.

CD/MD:

(3): REP 13

(4): SHUF 13

p OFF (Stop/Power off) button*

2

10, 11

*1 (CAT) is available only when the XM tuner is

connected.

*2

Warning when installing in a car without

an ACC (accessory) position on the

ignition switch

After turning off the ignition, be sure to press

and hold (OFF) on the unit until the display

disappears.

Otherwise, the display does not turn off and this

causes battery drain.

P

U

S

H

D

I

A

L

S

E

L

E

C

T

S

O

U

R

C

E

D

I

S

C

/

P

R

E

S

E

T

OPEN

6543

BBESHUFREP

21

BTMSENS

EQ3

D

S

P

L

M

O

D

E

CDX-F5500

DSO

SEEK SEEK

L

I

S

T

C

A

T

OFF

5

q DISC (ALBUM)/PRESET buttons (+/–)

To receive preset stations/change the disc*

1

,

skip albums*

2

.

*1 When an optional CD/MD unit is connected.

*2 Available only when an MP3 file is played.

r SEEK buttons (–/+)

To skip tracks/fast-forward, reverse a track/

tune in stations automatically, find a station

manually/select a setting.

The corresponding buttons of the card

remote commander control the same

functions as those on this unit.

a DSPL button

b SOURCE button

c SEEK (–/+) buttons

d OFF button

e VOL (+/–) buttons

f MODE button

g PRESET (DISC/ALBUM) (+/–) buttons

h ATT button

Note

If the display disappears by pressing (OFF), it cannot

be operated with the card remote commander unless

(SOURCE) on the unit is pressed, or a disc is inserted

to activate the unit first.

Tip

For details on how to replace the battery, see

“Replacing the lithium battery” on page 23.

S

E

K

SEEK

P

U

S

H

D

I

A

L

S

E

L

E

C

T

S

O

U

R

C

E

D

I

S

C

/

P

R

E

S

E

T

SENS

EQ3

D

S

P

L

M

O

D

E

DSO

SEEK SEEK

L

I

S

T

C

A

T

(SEEK)

(–): to select

leftwards/

.

(SEEK)

(+): to select

rightwards/

>

(DISC/PRESET)

(+): to select upwards

(DISC/PRESET)

(–): to select downwards

Card remote commander RM-X115

continue to next page t

ATTOFF

DSPL MODE

SOURCE

VOL

+

–

PRESET

+

PRESET

–

SEEK

–

SEEK

+

6

Selecting a disc and album with the

card remote commander

Disc and album can be skipped using the

PRESET (DISC/ALBUM) (+/–) buttons on the

card remote commander.

(With this unit)

(With optional unit)

* Available only when an MP3 file is played.

Skipping tracks continuously

Press once (SEEK) (+) or (SEEK) (–) on the

card remote commander, then press again within

2 seconds and hold.

Precautions

• If your car has been parked in direct sunlight,

allow the unit to cool off before operating it.

• Power antenna will extend automatically while

the unit is operating.

• While driving, do not use the CUSTOM FILE

feature or any other functions which may divert

your attention from the road.

If you have any questions or problems

concerning your unit that are not covered in this

manual, please consult your nearest Sony dealer.

Moisture condensation

On a rainy day or in a very damp area, moisture

condensation may occur inside the lenses and

display of the unit. Should this occur, the unit

will not operate properly. In such a case, remove

the disc and wait for about an hour until the

moisture has evaporated.

To maintain high sound quality

Be careful not to splash juice or other soft drinks

onto the unit or discs.

To Press

Skip albums*

–Album selection

+ or – [once for each album]

To continuously skip

albums, press and hold

either button.

To Press

Skip discs

–Disc selection

+ or – [once for each disc]

To continuously skip discs,

press once and press again

within 2 seconds (and hold)

either button.

Skip albums*

–Album selection

+ or – [hold for a moment]

and release

To continuously skip

albums, press (and hold)

within 2 seconds of first

releasing the button.

7

Notes on discs

• To keep a disc clean, do not touch its surface.

Handle the disc by its edge.

• Keep your discs in their cases or disc

magazines when not in use.

• Do not subject discs to heat/high temperature.

Avoid leaving them in a parked car or on a

dashboard/rear tray.

• Do not attach labels, or use discs with sticky

ink/residue. Such discs may stop spinning

when used, causing a malfunction, or may ruin

the disc.

• Do not use any discs with labels or stickers

attached.

The following malfunctions may result from

using such discs:

– Inability to eject a disc (due to a label or

sticker peeling off and jamming the eject

mechanism).

– Inability to read audio data correctly (e.g.,

playback skipping, or no playback) due to

heat shrinking of a sticker or label causing a

disc to warp.

• Discs with non-standard shapes (e.g., heart,

square, star) cannot be played on this unit.

Attempting to do so may damage the unit. Do

not use such discs.

• You cannot play 8 cm (3 in) CDs.

• Before playing, clean the discs with a

commercially available cleaning cloth. Wipe

each disc from the center out. Do not use

solvents such as benzine, thinner, commercially

available cleaners, or antistatic spray intended

for analog discs.

Music discs encoded with copyright

protection

This product is designed to play back discs that

conform to the Compact Disc (CD) standard.

Recently, various music discs encoded with

copyright protection are marketed by some

record companies. Please be aware that among

those discs, there are some that do not conform to

the CD standard and may not be playable by this

product.

Notes on CD-Rs (recordable CDs)/CD-

RWs (rewritable CDs)

This unit can play the following discs:

• Some CD-Rs/CD-RWs (depending on the

equipment used for its recording or the

condition of the disc) may not play on this unit.

• You cannot play a CD-R/CD-RW that is not

finalized*.

• You can play MP3 files recorded on CD-

ROMs, CD-Rs, and CD-RWs.

• A CD-R/CD-RW to which a session can be

added can be played.

* A process necessary for a recorded CD-R/CD-RW

disc to be played on the audio CD player.

Type of discs Label on the disc

Audio CD

MP3 files

8

About MP3 files

MP3 (MPEG 1 Audio Layer-3) is a standard

technology and format for compressing a sound

sequence. The file is compressed to about 1/10 of

its original size. Sounds outside the range of

human hearing are compressed while the sounds

we can hear are not compressed.

Notes on discs

You can play MP3 files recorded on CD-ROMs,

CD-Rs, and CD-RWs.

The disc must be in the ISO 9660*

1

level 1 or

level 2 format, or Joliet or Romeo in the

expansion format.

You can use a disc recorded in Multi Session*

2

.

*1 ISO 9660 Format

The most common international standard for

the logical format of files and folders on a

CD-ROM.

There are several specification levels. In

Level 1, file names must be in the 8.3 format

(no more than 8 characters in the name, no

more than 3 characters in the extension

“.MP3”) and in capital letters. Folder names

can be no longer than 8 characters. There can

be no more than 8 nested folder levels. Level

2 specifications allow file names up to 31

characters long.

Each folder can have up to 8 trees.

For Joliet or Romeo in the expansion format,

make sure of the contents of the writing

software, etc.

*2 Multi Session

This is a recording method that enables

adding of data using the Track-At-Once

method. Conventional CDs begin at a CD

control area called the Lead-in and end at an

area called Lead-out. A Multi Session CD is a

CD having multiple sessions, with each

segment from Lead-in to Lead-out regarded

as a single session.

CD-Extra: The format which records audio

(audio CD data) as tracks on session 1, and

records data as tracks on session 2.

Mixed CD: In this format, data is recorded as

track 1, and audio (audio CD data) is recorded

as track 2.

Notes

• With formats other than ISO 9660 level 1 and level 2,

folder names or file names may not be displayed

correctly.

• When naming, be sure to add the file extension

“.MP3” to the file name.

• If you put the extension “.MP3” to a file other than

MP3, the unit cannot recognize the file properly and

will generate random noise that could damage your

speakers.

• The following discs take a longer time to start

playback.

– a disc recorded with complicated tree structure.

– a disc recorded in Multi Session.

– a disc to which data can be added.

Cautions when playing a disc that is recorded in

Multi Session

• When the first track of the first session is audio CD

data:

Only audio CD data of the first session is played

back.

Any data in subsequent sessions is skipped.

• When the first track of the first session is not audio

CD data:

– If an MP3 file is in the disc, only MP3 file(s) is

played back and other data is skipped. (Audio CD

data is not recognized.)

– If no MP3 file is in the disc, “NO MUSIC” is

displayed and nothing is played back. (Audio CD

data is not recognized.)

9

The playback order of the MP3 files

The playback order of the folders and files is as

follows:

Notes

• A folder that does not include an MP3 file is skipped.

• When you insert a disc with many trees, it takes a

longer time to start playback. We recommend that

you make only 1 or 2 trees for each disc.

• Maximum folder number: 150 (including root folder

and empty folders)

• The maximum number of MP3 files and folders that

can be contained in a disc: 300

When a file/folder name contains many characters,

this number may become less than 300.

Tip

To specify a desired playback order, before the folder

or file name, input the order by number (e.g., “01,”

“02”), then record contents onto a disc. (The order

differs depending on the writing software.)

Getting Started

Resetting the unit

Before operating the unit for the first time, or

after replacing the car battery or changing the

connections, you must reset the unit.

Remove the front panel and press the RESET

button with a pointed object, such as a ball-point

pen.

Note

Pressing the RESET button will erase the clock setting

and some stored contents.

1

2

6

3

5

7

1

2

6

7

4

8

3

5

8

4

9

Folder (album)

MP3 file (track)

Tree 1

(root)

Tree 2

Tree 4

Tree 5

Tree 3

RESET button

10

Detaching the front panel

You can detach the front panel of this unit to

protect the unit from being stolen.

Caution alarm

If you turn the ignition switch to the OFF

position without removing the front panel, the

caution alarm will beep for a few seconds.

If you connect an optional amplifier and do not

use the built-in amplifier, the beep sound will be

deactivated.

1 Press (OFF)*.

CD/MD playback or radio reception stops

(the key illumination and display remain on).

* If your car has no ACC (accessory) position on

the ignition switch, be sure to turn the unit off by

pressing (OFF) until the display disappears to

avoid car battery drain.

2 Press (OPEN), then slide the front

panel to the right, and gently pull out

the left end of the front panel.

Notes

• If you detach the panel while the unit is still turned

on, the power will turn off automatically to prevent

the speakers from being damaged.

• Do not drop or put excessive pressure on the front

panel and its display window.

• Do not subject the front panel to heat/high

temperature or moisture. Avoid leaving it in a parked

car or on a dashboard/rear tray.

Tip

When carrying the front panel with you, use the

supplied front panel case.

Attaching the front panel

Place hole A of the front panel onto the spindle

B on the unit, then lightly push the left side in.

Press (SOURCE) on the unit (or insert a CD) to

operate the unit.

Note

Do not put anything on the inner surface of the front

panel.

1

2

A

B

x

11

Setting the clock

The clock uses a 12-hour digital indication.

Example: To set the clock to 10:08

1 Press (DSPL) for 2 seconds.

The hour indication flashes.

1 Rotate the volume control dial to set

the hour.

2 Press the select button.

The minute indication flashes.

3 Rotate the volume control dial to set

the minute.

2 Press (DSPL).

The clock starts. After the clock setting is

complete, the display returns to normal play

mode.

CD Player

CD/MD Unit (optional)

In addition to playing a CD with this unit, you

can also control external CD/MD units.

Playing a disc

(With this unit)

1 Press (OPEN) and insert the disc

(labeled side up).

2 Close the front panel.

Playback starts automatically.

If a disc is already inserted, press (SOURCE)

repeatedly until “CD” appears to start playback.

* Available only when an MP3 file is played.

To skip tracks continuously, press (SEEK) (+) or

(SEEK) (–), then press again within 2 seconds

and hold.

To Press

Stop playback (OFF)

Eject the disc (OPEN) then Z

Skip tracks

– Automatic

Music Sensor

(SEEK) (–/+)

(./>)

[once for each track]

Fast-forward/

reverse

– Manual Search

(SEEK) (–/+)

(m/M)

[hold to desired point]

Skip albums*

–Albums selection

(DISC/PRESET) (+/–)

[hold to desired point]

continue to next page t

12

Notes

• Before playing a track, this unit reads all track and

album information on the disc. Depending on the

track structure, it may take more than a minute

before playback begins. During this time, “READ” is

displayed. Play will automatically start when reading

is complete.

• Depending on the condition of the disc, it may not

play back (page 7, 8).

• While the first/last track on the disc is playing, if

(SEEK) (–) or (SEEK) (+) is pressed, playback skips

to the last/first track of the disc.

• When the last track on the disc is over, playback

restarts from the first track of the disc.

• If you play a high-bit rate MP3 file such as 320 kbps,

sound may be intermittent.

(With optional unit)

1 Press (SOURCE) repeatedly to select

“CD” or “MD (MS*

1

).”

2 Press (MODE) repeatedly until the

desired unit appears.

Playback starts.

*1 MS: MG Memory Stick System-up Player MGS-X1

*2 Available only when an MP3 file is played.

Cautions when connecting MGS-X1 and MD unit(s)

This unit recognizes MGS-X1 as an MD unit.

• When you want to play MGS-X1, press (SOURCE) to

select “MS” or “MD.” When “MS” appears in the

source display, MGS-X1 starts to play. When “MD”

appears in the source display, press (MODE) to

select “MS,” to start playback.

• When you want to play an MD unit, press (SOURCE)

to select “MD” or “MS.” If your desired MD unit

appears in the source display, it starts to play. If “MS”

or another MD unit appears in the source display,

press (MODE) to select your desired MD unit, to

start playback.

Note when playing back a disc with non-audio CD

data/MP3 file

If a disc with non-audio CD data/MP3 file is inserted:

– in the case of this unit, “NO MUSIC” appears in the

display, and the display becomes the clock display

(CD playback stops).

– in the case of an optional MP3 compatible CD unit,

“NO MUSIC” appears in the display and playback of

the next disc starts.

– in the case of an optional CD unit, which is

incompatible with MP3, the disc will play back with

no sound.

Note

With an optional unit connected, playback of the same

source will continue on to the optional CD/MD unit.

Display items

When the disc/album/track changes, any

prerecorded title*

1

of the new disc/album/track is

automatically displayed. (If the A.SCRL (Auto

Scroll) function is set to “ON,” names exceeding

8 characters will be scrolled (page 20).)

*1 When pressing (DSPL), “NO NAME” indicates that

there is no Disc Memo (page 14) or no prerecorded

name to display.

*2 Only for CD TEXT discs with the artist name.

*3 Only for MP3 files.

Only track name/artist name/album name in ID3

tag is displayed.

When pressing (DSPL), “NO ID3” indicates that

there is no ID3 tag to display.

Notes

• Some characters cannot be displayed.

• For some CD TEXT discs or ID3 tags with very

many characters, information may not scroll.

• This unit cannot display the artist name for each

track of a CD TEXT disc.

Notes on MP3

• ID3 tag applies to version 1.0, 1.1, 2.2, 2.3 and 2.4.

• Some characters and signs cannot be displayed

(appear as “ *”). The maximum number of

displayable characters for an album (folder) name/

track (file) is 64 (Romeo) or 32 (Joliet); ID3 tag 30

characters (1.0, 1.1, 2.2 and 2.3) or 126 characters

(2.4).

• In the following cases, elapsed playing time may not

be displayed accurately.

– when an MP3 file of VBR (variable bit rate) is

played.

– during fast-forward/reverse.

Tips

• When the A.SCRL (Auto Scroll) function is set to

“OFF” and the disc/album/track is changed, the disc/

album/track name or ID3 tag does not scroll.

• When an MP3 file is played and the album is

changed, the new album number is displayed.

To Press

Skip discs

–Disc selection

(DISC/PRESET) (+/–)

[once for each disc]

Skip albums*

2

–Albums selection

(DISC/PRESET) (+/–)

[hold to desired point]

To Press

Switch display item ( DSPL)

Displayable items

• Disc

number/Track number/Elapsed

playing time

• Disc name*

1

/Artist name*

2

• Album (folder) name*

3

• Track (file) name*

1

*

3

• ID3 tag*

3

• Clock

Source

13

Playing tracks repeatedly

— Repeat Play

You can select:

• REP-TRACK — to repeat the current track.

•REP-ALBM*

1

— to repeat the tracks in the

current album.

•REP-DISC*

2

— to repeat the tracks in the

current disc.

*1 Available only when an MP3 file is played.

*2 Available only when one or more optional CD/MD

units are connected.

During playback, press (3) (REP)

repeatedly until the desired setting

appears in the display.

Repeat Play starts.

To return to normal play mode, select

“REP-OFF.”

Playing tracks in random

order

— Shuffle Play

You can select:

• SHUF-ALBM*

1

— to play the tracks in the

current album in random order.

• SHUF-DISC — to play the tracks in the current

disc in random order.

• SHUF-CHGR*

2

— to play the tracks in the

current optional CD (MD) changer in random

order.

• SHUF-ALL*

3

— to play all the tracks in all

connected CD (MD) units (including this unit)

in random order.

*1 Available only when an MP3 file is played.

*2 Available only when one or more optional CD (MD)

changers are connected.

*3 Available only when one or more optional CD units,

or two or more optional MD units are connected.

During playback, press (4) (SHUF)

repeatedly until the desired setting

appears in the display.

Shuffle Play starts.

To return to normal play mode, select

“SHUF-OFF.”

Note

“SHUF-ALL” will not shuffle tracks between CD units

and MD units.

14

Labeling a CD

— Disc Memo (When connecting a CD unit

with the CUSTOM FILE function)

You can label each disc with a custom name

(Disc Memo). You can enter up to 8 characters

for a disc. If you label a CD, you can locate the

disc by name (page 15).

1 Start playing the disc you want to label

in a CD unit with the CUSTOM FILE

function.

2 Press (LIST/CAT) for 2 seconds.

The unit will repeat the disc during the

labeling procedure.

3 Enter the characters.

1 Rotate the volume control dial to

select the desired character.

A y B y C ... y 0 y 1 y 2 ...

y + y – y

*

... y * y A

* (blank space)

2 Press the select button after

locating the desired character.

The next character flashes.

3 Repeat steps 1 and 2 to enter the

entire name.

4 To return to normal play mode, press

(LIST/CAT) for 2 seconds.

Tips

• Simply overwrite or enter “ ” to correct or erase a

character.

• You can label CDs on a unit without the CUSTOM

FILE function if that unit is connected along with a

CD unit that has the function. The Disc Memo will be

stored in the memory of the CD unit with the

CUSTOM FILE function.

Note

REP-TRACK/SHUF play is suspended until the name

edit is complete.

Viewing the Disc Memo

As a display item, the Disc Memo always takes

priority over any original CD TEXT information.

Tip

Other items can be displayed (page 12).

Erasing the Disc Memo

1 Press (SOURCE) repeatedly to select

“CD.”

2 Press (MODE) repeatedly to select the

CD unit storing the Disc Memo.

3 Press (LIST/CAT) for 2 seconds.

4 Press (DSPL) for 2 seconds.

The stored names will appear.

5 Rotate the volume control dial to

select the disc name you want to

erase.

6 Press the select button for 2 seconds.

The name is erased.

Repeat steps 5 and 6 if you want to erase

other names.

7 Press (LIST/CAT) for 2 seconds.

The unit returns to normal play mode.

Notes

• When the Disc Memo for a CD TEXT disc is erased,

the original CD TEXT information is displayed.

• If you cannot find the Disc Memo you want to erase,

try selecting a different CD unit in step 2.

To Press

View (DSPL) during CD/CD

TEXT disc playback

15

Locating a disc by name

— List-up (When connecting a CD unit with

the CD TEXT/CUSTOM FILE function, or an MD

unit)

You can use this function for discs that have been

assigned custom names*

1

or for CD TEXT

discs*

2

.

*1 Locating a disc by its custom name: when you

assign a name for a CD (page 14) or an MD.

*2 Locating discs by the CD TEXT information: when

you play a CD TEXT disc on a CD unit with the CD

TEXT function.

1 During playback, press (LIST/CAT).

The name assigned to the current disc appears

in the display.

2 Press (LIST/CAT) repeatedly until you

find the desired disc.

3 Press (SEEK) (+) or (SEEK) (–) to play

the disc.

Notes

• Once a disc name has been displayed for 5

seconds, the display goes back to its normal

playback mode.

• If there are no discs in the magazine, “NO DISC”

appears in the display.

• If a disc has not been assigned a custom file, “NO

NAME” appears in the display.

• The information appears only in upper case. There

are also some letters which cannot be displayed.

Radio

The unit can store up to 6 stations per band

(FM1, FM2, FM3, AM1 and AM2).

Caution

When tuning in stations while driving, use Best

Tuning Memory to prevent accidents.

Storing stations

automatically

— Best Tuning Memory (BTM)

The unit selects the stations with the strongest

signals within the selected band, and stores them

in the order of their frequency.

1 Press (SOURCE) repeatedly to select

the radio.

2 Press (MODE) repeatedly to select the

band.

3 Press (BTM) for 2 seconds.

The unit stores stations in the order of their

frequencies on the number buttons.

A beep sounds when the setting is stored.

Notes

• If only a few stations can be received due to weak

signals, some number buttons will retain their former

settings.

• When a number is indicated in the display, the unit

starts storing stations from the one currently

displayed.

16

Receiving the stored stations

1 Press (SOURCE) repeatedly to select

the radio.

2 Press (MODE) repeatedly to select the

band.

3 Press the number button ((1) to (6))

on which the desired station is stored.

If preset tuning does not work

— Automatic tuning/Local Seek Mode

Automatic tuning:

Press (S EEK) (+) or ( SEEK) (–) to

search for the station.

Scanning stops when the unit receives a

station. Repeat the operation until the desired

station is received.

Local Seek Mode:

If the automatic tuning stops too

frequently, press ( SENS) repeatedly

until “LOCAL-ON” appears.

Only the stations with relatively strong

signals will be tuned in.

To cancel the local seek mode, press (SENS)

twice when receiving FM.

Note

When receiving AM, to cancel the local seek mode,

press (SENS) (“LOCAL-OFF” appears).

Tip

If you know the frequency of the station you want to

listen to, press and hold (SEEK) (+) or (SEEK) (–) to

locate the approximate frequency, then press

(SEEK) (+) or (SEEK) (–) repeatedly to fine adjust to

the desired frequency (manual tuning).

If FM stereo reception is poor

— Monaural Mode

During radio reception, press ( SEN S)

repeatedly until “MONO-ON” appears.

The sound improves, but becomes monaural

(“ST” disappears).

To return to normal radio reception mode, press

(SENS) (“MONO-OFF” appears).

Tip

If FM broadcasts are difficult to hear, set DSO to

“OFF” (page 22).

Storing only the desired

stations

You can manually preset the desired stations on

any chosen number button.

1 Press (SOURCE) repeatedly to select

the radio.

2 Press (MODE) repeatedly to select the

band.

3 Press (SEEK) (+) or (SEEK) (–) to tune

in the station that you want to store.

4 Press the desired number button ((1)

to (6)) for 2 seconds until “MEM”

appears.

The number button indication appears in the

display.

Note

If you try to store another station on the same number

button, the previously stored station will be erased.

17

Storing station names

— Station Memo

You can assign a name to each radio station and

store it in memory. The name of the station

currently tuned in appears in the display. You can

assign a name using up to 8 characters for a

station.

Storing the station names

1 Tune in a station whose name you

want to store.

2 Press (LIST/CAT) for 2 seconds.

The unit will repeat the disc during the

labeling procedure.

3 Enter the characters.

1 Rotate the volume control dial to

select the desired character.

A y B y C ... y 0 y 1 y 2 ...

y + y – y

*

... y * y A

* (blank space)

2 Press the select button after

locating the desired character.

The next character flashes.

3 Repeat steps 1 and 2 to enter the

entire name.

4 To return to normal radio reception

mode, press (LIST/CAT) for 2 seconds.

Tip

Simply overwrite or enter “ ” to correct or erase a

character.

Erasing the station name

1 Press (SOURCE) repeatedly to select

the radio.

2 Press (MODE) repeatedly to select the

band.

3 Press (LIST/CAT) for 2 seconds.

4 Press (DSPL) for 2 seconds.

The stored names will appear.

5 Rotate the volume control dial to

select the station name you want to

erase.

6 Press the select button for 2 seconds.

The name is erased.

Repeat steps 5 and 6 if you want to erase

other names.

7 Press (LIST/CAT) for 2 seconds.

The unit returns to normal radio reception

mode.

Note

If you have already erased all of the station names,

“NO DATA” appears in step 6.

18

Tuning in a station through

a list

— List-up

1

During radio reception, press

(LIST/CAT)

.

The frequency or the name assigned to the

current station appears in the display.

2 Press (LIST/CAT) repeatedly until you

find the desired station.

If no name is assigned to the selected station,

the frequency appears in the display.

3 Press (S EEK) (+) or ( SEEK) (–) to tune

in the desired station.

Other Functions

You can also control the unit (and optional CD/

MD units) with a rotary commander (optional).

Using the rotary commander

First, attach the appropriate label depending on

how you want to mount the rotary commander.

The rotary commander works by pressing

buttons and/or rotating controls.

By pressing buttons

Press To

(SOURCE) Change the source

(Radio/CD/MD*

1

)/Power on

(MODE) Change operation

(Radio band/CD unit*

1

/MD

unit*

1

)

(ATT) Attenuate the sound

(OFF)*

2

Stop playback or radio

reception/Power off

(SEL) Adjust and select

(DSPL) Change the display item

SEL

DSPL

MODE

SEL

DSPL

MODE

OFF

Rotate the VOL control

to adjust the volume.

(SOURCE)

(SEL)

(ATT)

(DSPL)

(OFF)

(MODE)

19

By rotating the control

Rotate and release to:

– Skip tracks.

To continuously skip tracks, rotate once

and rotate again within 2 seconds and hold

the control.

– Tune in stations automatically.

Rotate, hold, and release to:

– Fast-forward/reverse a track.

– Find a station manually.

By pushing in and rotating the control

Push in and rotate the control to:

– Receive preset stations.

– Change discs during CD (MD) playback*

1

.

– Change albums*

3

.

*1 Only if the corresponding optional equipment is

connected.

*2 If your car has no ACC (accessory) position on the

ignition key switch, after turning off the ignition, be

sure to press and hold (OFF) until the display

disappears.

*3 Available only when an MP3 file is played.

When an MP3 file is played, you can select an

album using the rotary commander.

(With this unit)

(With optional unit)

Changing the operative direction

The operative direction of controls is factory-set

as shown below.

If you need to mount the rotary commander on

the right hand side of the steering column, you

can reverse the operative direction.

Press ( SEL ) for 2 seconds while

pushing the VOL control.

SEEK/AMS

control

PRESET/DISC

control

To Do this

Skip albums

– Album selection

Push in and rotate [once for

each album] the control.

To continuously skip

albums, push in and rotate

(and hold) the control.

To Do this

Skip discs

–Disc selection

Push in and rotate [once for

each disc] the control.

To continuously skip discs,

push in and rotate once and

rotate again within

2 seconds (and hold) the

control.

Skip albums

– Album selection

1 To enter Album selection

mode, push in, then rotate

and hold the control.

Within 2 seconds,

proceed to step 2.

2 Push in, then rotate

quickly and repeatedly, to

skip albums one by one.

To increase

To decrease

20

Adjusting the sound

characteristics

You can adjust the balance, fader, low pass filter

and subwoofer volume.

1 Press the select button repeatedly

until “BAL,” “FAD,” “LPF” or “SUB”

appears.

Each time you press the select button, the

item changes as follows:

LOW*

1

t MID*

1

t HI*

1

t

BAL (left-right) t FAD (front-rear) t

LPF (low pass filter)*

2

*

3

t

SUB (subwoofer volume)*

2

*

4

*1 When EQ3 is activated (page 21).

*2 When “SUB” is selected (page 20).

*3 The cut off frequency is adjustable to 78 Hz,

125 Hz or OFF.

*4 The volume level is adjustable between –10

and +10 steps. (Below –10, “ATT” is displayed.)

2 Rotate the volume control dial to

adjust the selected item.

Note

Adjust within 3 seconds after selecting the item.

Quickly attenuating the

sound

(With the rotary commander or the card

remote commander)

Press (ATT).

After “ATT-ON” momentarily appears,

“ATT” appears in the display.

To restore the previous volume level, press

(ATT) again.

Tip

When the interface cable of a car telephone is

connected to the ATT lead, the unit decreases the

volume automatically when a telephone call comes in

(Telephone ATT function).

Changing the sound and

display settings

The following items can be set:

•REAR/SUB*

1

— to switch the audio output

REAR or SUB.

– Select “REAR” to output to a power amplifier.

– Select “SUB” to output to a subwoofer.

• A.SCRL (Auto Scroll)*

2

(page 12).

• M.DSPL (Motion Display) — to turn the

motion display on or off.

– Select “ON” to activate the motion display

(the moving pattern appears in the display).

– Select “OFF” to deactivate the motion display.

•DEMO*

1

— to turn the demonstration display

on or off.

– Select “ON” to activate the demonstration

display (The demonstration starts about 10

seconds after the unit is turned off).

– Select “OFF” to deactivate the

demonstration display.

• BEEP*

3

— to turn the beeps on or off.

• DIM — to change the brightness of the display.

– Select “ON” to dim the display.

– Select “OFF” to deactivate the Dimmer.

La page charge ...

Sony CDX-F5500 Le manuel du propriétaire

Sony CDX-F5500 Le manuel du propriétaire

dans d''autres langues

Documents connexes