Hinkley 903160FMW-NDD Marin 60 Inch Indoor Outdoor Ceiling Fan Manuel utilisateur

60" MARIN™

CEILING FAN INSTRUCTION MANUAL

INDOOR / OUTDOOR LED FAN

LED

SO WE’RE HERE IF YOU HAVE A QUESTION, NEED SOME

HELP OR WANT TO CHAT ABOUT OUR PRODUCTS. SEND

SUGGESTIONS OUR WAY TOO—WE’RE ALWAYS LOOKING TO

MAKE YOUR EXPERIENCE WITH HINKLEY A POSITIVE ONE.

This manual contains complete instructions for the

installation and operation of this fan. It has been

designed to make the installation process as easy as

possible. If you are unfamiliar or uncomfortable with

wiring, please contact a qualiﬁed electrician. If you

need additional assistance or have any questions,

please reach out to us.

For warranty information, visit hinkley.com.

> SERVICE@HINKLEY.COM

> 800.HINKLEY

> LET’S SEE THAT HINKLEY STYLE @HINKLEY

#HINKLEYSTYLE

WE WANT YOU TO LOVE YOUR NEW FAN

WARNING:

Read and follow these instructions carefully and be mindful of all warnings shown throughout.

TABLE OF CONTENTS

02 GENERAL INSTALLATION & OPERATING

INSTRUCTIONS

03 IMPORTANT SAFETY PRECAUTIONS

03 TOOLS & MATERIALS REQUIRED

04 UNPACKING YOUR FAN

05 PREPARATION

05 INSTALLING THE HANGING BRACKET

06 HANGING THE FAN

08 ELECTRICAL CONNECTIONS

FINISHING THE INSTALLATION

09

INSTALLING THE BLADES10

INSTALLING THE MONTING PLATE

10

11 INSTALLING THE LED ASSEMBLY AND GLASS SHADE

12

INSTALLING THE WALL CONTROL

INSTALLING THE FAN WITHOUT THE LIGHT KIT (OPTIONAL)

13

15

17

18

19

OPERATION

CARE AND CLEANING

TROUBLESHOOTING

ENERGY GUIDE

SPECIFICATIONS

SMART BY BOND

GENERAL INSTALLATION & OPERATION INSTRUCTIONS

02 | hinkley.com

1

2

3

4

5

6

7

8

9

10

11

12

13

14

To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning.

To avoid possible electric shock, be sure electricity is turned oﬀ at the main power box before wiring. All electrical connections

must be made in accordance with local codes, ordinances and/or the National Electric Code. If you are unfamiliar with the

methods of installing electrical wiring and products, secure the services of a qualiﬁed and licensed electrician as well as

someone who can check the strength of the supportive ceiling members and make the proper installation(s) and connections.

WARNING: To reduce the risk of ﬁre, electric shock, or other personal injury, mount fan only on an outlet box or supporting system

marked acceptable for fan support of 35 lbs (15.9 kg) or less and use mounting screws provided with the outlet box. Most outlet

boxes commonly used for the support of lighting ﬁxtures are not acceptable for fan support and may need to be replaced.

Consult a qualiﬁed electrician if in doubt.

Make sure that your installation site will not allow rotating fan blades to come in contact with any object. Blades should be at least

7 feet from ﬂoor.

Blades should be attached after motor housing is hung and in place. Fan motor housing should be kept in the carton until ready

to be installed to protect its ﬁnish. If you are installing more than one ceiling fan, make sure that you do not mix fan blade sets, as

each blade is part of a weighted set.

After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The

wires should be spread apart with the common conductor and the grounding conductor on one side of the outlet box, and the

"HOT" wires on the other side.

Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed and should be installed

per the light kit's installation instructions.

After fan is completely installed, check to make sure that all connections are secure to prevent fan from falling and/or causing

damage or injury.

The fan can be made to work immediately after installation - the bearings are adequately charged with grease so that, under

normal conditions, further lubrication should not be necessary for the life of the fan.

To operate the reverse function on this fan, press the reverse button while the fan is running.

CAUTION: Do not ingest battery - Chemical bum hazard. Keep new and used batteries away from children.

The remote control supplied with a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe

internal bums in just 2 hours and can lead to death.

If the battery compartment does not close securely, stop using the product and keep it away from children.

If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

IMPORTANT SAFETY PRECAUTIONS

TOOLS & MATERIALS REQUIRED

WARNINGS:

• PHILLIPS SCREWDRIVER

• FLAT SCREWDRIVER

• WRENCH OR PLIERS

• WIRE CUTTER

• STEPLADDER

• WIRING SUPPLIES AS REQUIRED BY

ELECTRICAL CODE

NOTE:

The important precautions, safeguards and instructions appearing in this manual are not meant to cover all possible conditions

and situations that may occur. It must be understood that common sense, caution and carefulness are factors which cannot be

built into this product. These factors must be supplied by the person(s) installing, caring for and operating the unit.

• Disconnect power by removing fuse or turning oﬀ circuit breaker before installing the fan and/or optional lighting.

• Support directly from building structure.

• To reduce the risk of ﬁre, electric shock, or personal injury, mount to outlet box marked "acceptable for fan support" and use mounting

screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting ﬁxtures are not acceptable for fan

support and may need to be replaced. Consult a qualiﬁed electrician if in doubt.

• Do not use an incandescent light dimmer. Do not use this fan with any transformer type fan speed control device.

• To reduce the risk of personal injury, do not bend the blade arms when installing them, balancing the blades or cleaning the fan. Do not

insert any objects(s) between rotating fan blades.

UNPACKING YOUR FAN

UNPACK YOUR FAN AND CHECK THE CONTENTS.

NOTE: Design of parts shown above may look slightly diﬀerent for

your speciﬁc model of fan.

04 | hinkley.com

1

2

8

9

10

3

• Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove all

parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged.

• Examine all parts. You should have the following:

4

PACKAGE CONTENT

1 Blade Set of 3

Blade Support Plates2

Hanging Bracket

3

Ceiling Canopy and Trim Ring

4

5

6

7

8

9

10

12

13

14

15

Downrod Asm.

Yoke Cover

Metal Cover (for no light use)

Fan Housing with Rope Assembly

Adapter Plate A

XX=FAN FINISH

5

6

7

11

12

13

14

15

LED Assembly 16W

Adapter Plate B (for no light use)

Glass Shade

Bracket Mounting Hardware

(wood screws, screws, lock

washers, star washers, ﬂat washers,

wire nuts),

Blade to Motor Screws

w/Fiber Washers,

Balance Kit,

Safety cable hardware

(wood screw, ﬂat washer)

11

Hardware Bag

Receiver Incl. 5 Wire Nuts

BL903160Fxx

DR94014Fxx

YC900752Fxx

RH903160Fxx

E903160LED

GL903160OPET

CNW903160

MH903160Fxx

CA900752Fxx

x

Cradle A, Wall Plate, Face Plate,

2 Mounting Screws,

Wall Control w/2032 Battery,

Cradle B (for ﬂat wall use only)

980014FWH-R

PREPARATION

INSTALLING THE HANGING BRACKET

PREPARATION:

Parts identiﬁcation on assembled fan.

Ceiling Fan

Outlet Box

Hanger

Bracket

Outlet Box

Screw

Flat Washer

Lock Washer

Fig. 1

Verify you have all parts before beginning

the installation. Check foam insert closely for

missing parts. Remove motor from packing.

To avoid damage to ﬁnish, assemble motor

on soft padded surface or use the original

foam inset in motor box.

DO NOT LAY MOTOR HOUSING ON ITS SIDE

AS THIS COULD RESULT IN SHIFTING OF

MOTOR IN DECORATIVE ENCLOSURE.

CAUTION: To avoid possible electrical shock, be sure electricity is turned oﬀ

at the main power box before wiring. All wiring must be in accordance with

National and Local Electrical Codes and the ceiling fan must be grounded as

a precaution against possible electric shock.

1

2

3

4

Locate ceiling joist where fan is to be mounted, being sure location

agrees with the requirements in the minimum clearance section of this

guide. Wood joists must be sound and of adequate size to support 35

pounds (See page 2, items 3 and 4).

If not already present, mount a UL listed outlet box marked "suitable for

fan support" following the instructions provided with the outlet box. The

outlet box must be able to support a minimum of 35 pounds.

Remove canopy from hanger bracket. Remove twist-lock trim ring by

rotaing counter-clockwise. Remove canopy screw that does not have

key slot in canopy. Loosen screw with key slot and remove canopy.

Attach hanging bracket to outlet box using screws provided with the

outlet box.

Downrod

Blade

Yoke cover

Canopy

Motor Housing

LED Light Kit

HANGING THE FAN

1

2

3

4

5

06 | hinkley.com

Fig. 1

Fig. 2

Downrod

Cross pin

Hanger

ball Set screw

Downrod

Hook-up

(3) Wires

Mounting Collar

Downrod Pin

Security Screws

Cotter Pin

Top of

Fan Body

Remove ball from downrod by loosening set screw in the side

of the ball. Slide ball down and remove ball pin; remove ball.

(Fig. 1)

Carefully support fan body (motor) in its styrofoam packing with

the mounting collar (where the wires come out) facing upward.

Loosen the two security set screws and remove the downrod

pin and retaining clip from the coupling on top of the motor

assembly. (Fig. 2)

Carefully feed the electrical lead wires and safety cable from

the fan through the downrod. Thread downrod into coupler

until holes align. Insert downrod pin through holes in mounting

collar and downrod; clip cotter pin through small hole in end of

downrod pin to hold downrod in place.

Tighten security set screws against downrod using a large ﬂat

blade screwdriver to ensure a tight ﬁt against downrod.

Tighten nuts against mounting collar.

Safety Cable

07

Fig. 3

Ground Wire

Top of

Fan Body

Hook-up (3) Wires

Yoke Cover

Downrod

Canopy

Hanger ball

Set screw

Cross Pin

Ball Moisture Cap

REMEMBER to turn oﬀ the power before you begin.

To properly install your ceiling fan, follow the steps below.

Slip the yoke cover, trim ring and canopy onto the downrod. (Fig. 3)

Slide the hanger ball onto the downrod, insert the cross pin through

the downrod and tighten. Tighten the set screw.

Feed wires through holes in rubber ball moisture cap and slide cap

down over top of ball. (Fig. 3)

Lift ball/downrod/fan into hanger bracket opening.

NOTE: The tab opposite hanger bracket opening should ﬁt in slot

on ball. (Fig. 4)

6

7

8

9

NOTE

6 feet of lead wire is supplied on the fan for use with

longer downrods.

Trim Ring

Safety Cable

Fig. 4

Attach the wood screw and the ﬂat washer to the ceiling joist as

shown (do not fully tighten). Slide the cable clamp onto the

safety cable from the fan. Loop the safety cable around the

wood screw that was just attached to ceiling joist. Feed the end

of the cable into the clamp and pull as much cable through as

possible. Firmly tighten screw in the clamp. Cut oﬀ excess cable.

INSTALLATION OF SAFETY CABLE SUPPORT

Safety Cable Clamp

Safety Cable

Wood Ceiling Joist

Safety Cable Loop

Wood Screw

And Washer

08 | hinkley.com

ELECTRICAL CONNECTIONS

Fig. 1

Receiver

Hanger

bracket

REMEMBER -Turn oﬀ the power! NOTE - Control must be installed within 30 feet of fan.

WARNINGS: Check to see that all connections are tight, including ground, and

that no bare wire is visible at the wire nuts, except for the ground wire.

CAUTION: To reduce the risk of electric shock, this fan must be installed with an

isolating wall control/switch.

1.

Insert the receiver into the ceiling mounting bracket with the ﬂat side of the

receiver facing the ceiling. (Fig. 1) For best performance, make sure the

Black Antenna and WIFI Antenna, on the end of the receiver, remains

extended and not tangled with any of the electrical wires.

2. Make wire connections from the fan to the receiver unit. For this

step use the bundle of 5 wires on the receiver. (Fig. 2)

Connect the YELLOW fan wire to the YELLOW receiver wire.

Connect the GRAY fan wire to the GRAY receiver wire.

Connect the RED fan neutral wire to the RED receiver neutral wire.

Connect the WHITE fan neutral wire to the WHITE receiver neutral wire.

Connect the BLUE fan neutral wire to the BLUE receiver neutral wire.

3. Connect the wiring from the ceiling to the receiver unit. (Use the 2 wire

bundle on the receiver.) Secure with supplied wire nuts.

Connect the BLACK building supply wire to the BLACK receiver wire.

Connect the WHITE receiver neutral wire to the WHITE building neutral wire.

Connect the COPPER building ground wire to the 4 YELLOW/GREEN ground

wires from the fan and receiver.

Fig. 2

YELLOW / GRN (hanger bracket)

Receiver

Fan

Outlet box

Ceiling

WH (AC IN)

GROUND

WH

BLK

BLK (AC IN)

YELLOW / GRN

WHITE

(For light)

RED

YELLOW

GRAY

BLUE (For light)

YELLOW / GRN (downrod)

FINISHING THE INSTALLATION

1

2

3

1

2

Tuck connections neatly into ceiling outlet box.

Slide the canopy up to mounting bracket and place the

key hole on the trim ring the screw on the mounting

bracket, turn canopy until it locks in place at the narrow

section of the key holes.

Align the circular hole on canopy with the remaining

hole on the mounting bracket, secure by tightening the

two set screws.

NOTE: Adjust the canopy screws as necessary until the

canopy and trim ring are snug.

Canopy

Trim Ring

Screws

WARNING:

Make sure the hook on the hanging bracket properly sits in the groove in the hanger ball before

attaching the canopy to the bracket by turning the housing until it drops into place.

Ceiling Fan

Outlet Box

Hanger

Bracket Groove

10 | hinkley.com

INSTALLING THE MONTING PLATE

INSTALLING THE BLADES

CAUTION: Remove the two rubber packing mounts from the fan

motor assembly and discard prior to attaching the blades.

Insert the blade through the slot on the housing. Align the holes

on the blade and the fan motor assembly and secure with the

blade support plates and blade attachment screws.

NOTE:

Cordless power screwdrivers are NOT recommended,

as they usually strip the heads of the screws and

usually will not fully compress the lock washers on

the motor screws. Use a large ﬂat blade screwdriver

for ﬁnal tightening to fully compress the washers. This

will help ensure proper alignment of the blades and

noise-free, wobble-free running.

1

2

3

NOTE: Be sure the power is oﬀ before installing.

Remove one of the three screws on the mounting hub

located on the fan motor. Loosen the other 2 screws. (Do

not remove) (Fig. 1)

Pass the light wires through the center hole of the adapter

plate A.

Place the key holes on the adapter plate A over the 2

screws previously loosened, turn the adapter plate until it

locks in place at the narrow section of the key holes.

Secure by tightening the 2 screws previously loosened

and the one previously removed.

Fig. 1

NOTE: Remove any rubber supports that are installed for

shipping.

Blades

Blade

support

plates

Screws

Mounting Hub

(bottom of motor)

Adapter

plate A

Light Wires

INSTALLING THE LED ASSEMBLY AND GLASS SHADE

1

2

3

4

5

NOTE: Be sure the power is oﬀ before installing.

Remove one of the three screws on the adapter plate located

on the fan motor. Loosen the other 2 screws. (Do not remove)

(Fig. 2)

While holding the LED assembly under your fan, make the

polarized plug connections: (Fig. 2)

- Red to white

- Black to black

Tuck connections neatly into adapter plate. Place the key

holes on the LED assembly over the 2 screws previously

loosened, turn the LED assembly until it locks in place at the

narrow section of the key holes. Secure by tightening the 2

screws previously loosened and the one previously removed.

Raise the glass shade against the LED assembly and turn

clockwise until snug, DO NOT OVERTIGHTEN.

Restore power and your LED assembly is ready for operation.

Fig. 2

LED

assembly

Wire connectors

Glass shade

Screws

12 | hinkley.com

INSTALLING THE FAN WITHOUT THE LIGHT KIT (OPTIONAL)

1

2

Fig. 1

Screws

Adapter Plate B

Fig. 2

Metal Cover

Remove one of the three screws on the mounting hub

located on the fan motor. Loosen the other 2 screws. (Do

not remove) (Fig. 1)

Place the key holes on the adapter plate B over the 2

screws previously loosened, turn the adapter plate until it

locks in place at the narrow section of the key holes.

Secure by tightening the 2 screws previously loosened

and the one previously removed.

1Secure the metal cover to the adapter plate B.

Mounting Hub

(bottom of motor)

INSTALLING THE WALL CONTROL

Fig. 1

Fig. 2

REMEMBER to turn oﬀ the power before you begin.

NOTE - Secures to any surface or application: ﬂat wall, single gang

box, multi gang box.

1

2

3

4

Outlet box

Option 1. Flat Surface Installation

Select a desired location. Use the wall plate to mark the

location of the mounting holes. Plastic wall anchors or

mounting screws are needed for this application. (Fig. 1)

Seat the cradle B into the wall plate. Secure the wall plate to

the wall using the provided hardware.

Snap the face plate cover onto the wall bracket.

Remote transmitter will be held in place with built in magnets.

Remove the existing wall plate and the old switch from the wall outlet

box.

Seat the cradle A into the wall plate. (Fig. 2)

Connect the black lead wires from the switch in the cradle A to the

black wires in the switch box. Hot input wire to one of the cradle A

switch leads. Power lead to the fan is connected to the remaining

switch lead.

Connect the wall plate / cradle A assembly to the wall outlet box

using the supplied hardware.

Snap the face plate cover onto the wall bracket.

Remote transmitter will be held in place with built in magnets.

1

2

3

4

5

6

Option 2. For single gang box

Transmitter

Face plate

Wall plate

Cradle B

Cradle A

Wall

Plastic

anchor

HIRO Control System

Fig. 3

Remove the existing wall plate and old switch from the wall

outlet box. (Fig. 3)

Connect the black lead wires from the switch in the cradle A

to the black wires in the switch box. Hot input wire to one of

the cradle switch leads. Power lead to the fan is connected

to the remaining switch lead. (Fig. 4)

Attach the cradle A to the wall switch box using the supplied

hardware.

Attach the multi-gang faceplate to the switch set in the wall

outlet box. Cradle A of Hinkley switch will ﬁt in any standard

decora face plate.

Remote transmitter will be held in place with built in magnets.

1

2

3

4

5

Option 3. Multi Gang Wall Switch Box Installation

Fig. 4

Outlet box

Face plate

Switch

Outlet box

Transmitter

Face plate

Cradle A

HIRO Control System

14 | hinkley.com

OPERATION

Your DC brushless motor is equipped with an

automatically learned type remote control.

There is no frequency switches on the receiver

or transmitter. The fan can start to use once the

pairing process is done.

Remove the panel from the transmitter and then

install one 2032 battery (included). You need to

use a coin to open or close the battery cover.

To prevent damage to transmitter, remove the

battery if not use for long periods of time (Fig. 1)

Fig. 1

Fig. 2

Signal light

ON

OFF

1

2

3

4

5

button:

Press this button and release instantly to

turn on or off the light.

button:

Press and hold to dim or brighten lights

to the desired level and release.

button:

Press this button to set fan wind direction

up or down.

button:

Press button for turn on and setting 1-6

fan speed.

button:

Press this button to turn the fan off.

Signal light (Fig. 2)

6

WARNING: Chemical Burn Hazard. Keep

batteries away from children.

This product contains a lithium button/coin cell

battery. If a new or used lithium button/coin cell

battery is swallowed or enters the body, it can

cause severe internal burns and can lead to

death in as little as 2 hours. Always completely

secure the battery compartment. If the battery

compartment does not close securely, stop

using the product, remove the batteries, and

keep it away from children. IF you think

batteries might have been swallowed or placed

inside any part of the body, seek immediate

medical attention.

The batteries shall be disposed of properly,

including keeping them away from children;

Even used cells may cause injury.

HIRO Control System

Pairing Process

NOTE: If installing/pairing more than

one fan in an area, the power must be

disconnected from all fans except the one

fan being paired.

With the fan’s power off, restore power to the

fan. Press and hold “ ” button for about 5

seconds and release. If optional light kit is

installed, the light kit will flash three times and

the motor spin up for 10 seconds on low speed.

The fan has completed the pairing process with

the wall control and is ready for use.

NOTE: A single fan can be controlled with as

many as 3 wall controls in one room. Every

control will need to repeat the pairing process

based on instructions above and all controls

must be within 30 feet of the fan.

1

2

3

4

Fig. 3 Fig. 4

SUMMER MODE

(COUNTERCLOCKWISE DIRECTION)

WINTER MODE

(CLOCKWISE DIRECTION)

Summer Mode and Winter Mode Operation

IMPORTANT: To prevent damage or cause injury, be sure that fan is switched to oﬀ and blades have stopped moving completely

before attempting to change direction of rotation.

The reverse switch is located on the top of the motor housing. Slide the switch to the right for winter mode operation. Slide the

switch to the left for summer mode operation. Make sure switch is not stuck between forward and reverse positions.

Summer Mode (forward):

A DOWNWARD airﬂow creates a cooling eﬀect as shown in Figure 3. This allows you to set your air conditioner on a warmer setting

without aﬀecting your comfort.

Winter Mode (Reverse):

An UPWARD airﬂow moves warmer air oﬀ the ceiling area as shown in Figure 4. This allows you to set your heating unit on a cooler

setting without aﬀecting your comfort.

16 | hinkley.com

CARE AND CLEANING

TROUBLESHOOTING

PROBLEM SOLUTION

Periodically it may be necessary to re-tighten blade to blade arm screws or blade arm to motor screws to prevent clicking or humming sound

during operation. This is especially true in climates with broad temperature and humidity ranges.

When dusting the blades, you must support the blade to prevent bending - no pressure should be applied to the blades. If you experience any

ﬂaws in the operation of your fan, please check the following points.

Fan Will

Not Start

Fan Sounds

Noisy

Fan Wobbles

Remote Control

Malfunction.

1. Check main and branch circuit breakers and/or fuses.

2. Check line wire connections to fan housing wiring. Make sure forward/reverse switch is set to one or the other

position, not stuck in between.

3. Check to make sure the dip switches from the transmitter and receiver are set to the same frequency.

1. Check and make sure that all screws in motor housing are snug (but not over tight).

2. Check that the screws securing blade arms to the motor are tight.

3. Check that wire connectors in switch housing are not rattling against each other or the interior wall of the switch

housing.

4. Check that all glassware is ﬁnger tight and that bulb(s) are well held in the sockets, if a light kit is used.

5. Check that the canopy is ﬁrmly attached to hanging bracket and not vibrating against ceiling.

1. Check that all blades are ﬁrmly screwed into blade arms. Check that all blade arms are ﬁrmly secure to the motor.

2. Check to make sure that light kit (if present) is ﬁrmly attached to switch housing and that all glassware and shades

are fastened properly. Wobble can also result from even the smallest deviations in distance from blade tip to blade

tip.

3. If measurements from blade tip to blade tip are not equal, loosen screws connecting blade to blade arm one at a

time and adjust blade(s) so that distances are equal.

4. Interchanging adjacent blades may redistribute mass and result in smoother operation. Blade arms can be bent

slightly to restore same pitch to all blades if a blade is diﬀerent than the other blades when viewed edge on.

5. Most wobble can be traced to a loose electrical box or mounting bracket. Make sure these are tight and the ball is

completely seated in the bracket.

6. Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable.

WARNING: To reduce the risk of personal injury, do not bend the blade arm while installing, balancing the blades, or

cleaning the fan. Do not insert foreign objects between rotating fan blades.

1. Do not connect the fan with a wall mounted variable speed control(s).

2. Make sure the dip switches are set correctly.

CAUTION:

Switch oﬀ power supply before carrying out any of these checks.

ENERGY GUIDE SPECIFICATIONS

AVERAGE PERFORMANCE AND ENERGY INFORMATION

ftc.gov/energy

• The higher the airflow, the

more air the fan will move

• Airflow Efficiency: 273 Cubic

Feet Per Minute Per Watt

Airflow

4,601

Cubic Feet Per Minute

• Based on 12 cents per kWh and 6.4 hours use per day

• Your cost depends on rates

• Energy Use: 17 Watts

and use

$

3

$

34

Cost Range of Similar Models (19” – 84”)

$5

Estimated

Yearly Energy Cost

All estimates based on typical use, excluding lights

Airﬂow Shown Is a Weighted Average of High and Low Cubic Feet per Minute Based on Downrod

6324 2648

26.6 2.9

238 919

PERFORMANCE

SPECIFICATIONS

STANDARD

HIGH SPEED LOW SPEED

Airﬂow (CFM)

Energy Use (Watts)

Airﬂow Eﬃciency (CFM/W)

Energy Costs (Yearly)

Amps 0.0 0.0

RPMs 00

$5 $1

18 | hinkley.com

La page charge ...

Hinkley 903160FMW-NDD Marin 60 Inch Indoor Outdoor Ceiling Fan Manuel utilisateur

Hinkley 903160FMW-NDD Marin 60 Inch Indoor Outdoor Ceiling Fan Manuel utilisateur

dans d''autres langues