City Theatrical 5850 QolorPIX Tape Controller Manuel utilisateur
- Taper
- Manuel utilisateur
QolorPIX® Tape Controller, Eight Output
User’s Manual
Rev 1.1
© 2020 City Theatrical, Inc.
Multiverse® Transceivers are covered by U.S. Patent # 7,432,803 and other patents pending.
P/N 5850
5850 Series QolorPIX Tape Controller
2
1
Foreword
1.1
Compliance Notice
ETL Listed to UL508A
1.2
Safety Notice
□
Warning: No user serviceable parts inside. Service should be performed by qualified
personnel only.
□
The QolorPIX Tape Controller is designed for use in dry locations only.
Exposure to rain or moisture may cause damage to the controller and
increase risk of electrical shock.
□
Check all external wiring before applying power.
□
Devices rigged overhead must include an appropriately rated safety cable.
5850 Series QolorPIX Tape Controller
3
Table of Contents
1
Foreword .................................................................................................................................. 2
2
Compliance .............................................................................................................................. 4
3
Introduction .............................................................................................................................. 6
4
Specifications ........................................................................................................................... 8
5
Configuration ......................................................................................................................... 11
6
DMX Characteristics .............................................................................................................. 15
7
Troubleshooting ..................................................................................................................... 18
8
Accessories ............................................................................................................................ 18
List of Tables
Table 1: Physical Characteristics ................................................................................................... 8
Table 2: 16-Channel DMX Map .................................................................................................... 15
Table 3: Effect List ........................................................................................................................ 16
Table 4: Troubleshooting .............................................................................................................. 17
Table 5: Accessories ..................................................................................................................... 18
List of Figures
Figure 1: What’s Included ............................................................................................................... 7
Figure 2: Pipe Mount ....................................................................................................................... 8
Figure 3: Rack Mount ............................................................................................................................. 9
Figure 4: Surface Mount......................................................................................................................... 9
Figure 5: Air Flow ............................................................................................................................ 9
Figure 6: Face Panel ..................................................................................................................... 10
Figure 7: Pinout ............................................................................................................................. 10
5850 Series QolorPIX Tape Controller
4
2
Compliance
2.1
FCC Compliance Statement (United States)
This device complies with Part 15 of the Federal Communications Commission (FCC) Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION:
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
2.2
IC Statement
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the
following two conditions:
1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
2.3
CE Mark Conformity
City Theatrical Inc. declares that this product conforms to the specifications listed in this manual,
following the provisions of the European R&TTE directive 1999/5/EC:
City Theatrical Inc. vakuuttaa täten että dieses produkt tyyppinen laite on direktiivin 1999/5/EY
oleellisten vaatimusten ja sitä koskevien näiden direktiivien muiden ehtojen mukainen.
City Theatrical Inc. déclare que le produit est conforme aux conditions essentielles et aux
dispositions relatives à la directive 1999/5/EC.
□
EN 301 489-1, 301 489-17 General EMC requirements for Radio equipment.
□
EN 62832 Safety
□
EN 300 328 Technical requirements for Radio equipment.
CAUTION—This equipment is intended to be used in all EU and EFTA countries. Outdoor use
5850 Series QolorPIX Tape Controller
5
may be restricted to certain frequencies and/or may require a license for operation. Contact local
Authority for procedure to follow.
Note: ESD precautions should be used when attaching or removing the antenna.
Note: Combinations of power levels and antennas resulting in a radiated power level of above
100 mW equivalent isotropic radiated power (EIRP) are considered as not compliant with the
above mentioned directive and are not allowed for use within the European community and
countries that have adopted the European R&TTEdirective 1999/5/EC. For more details on legal
combinations of power levels and antennas, contact City Theatrical Inc.
Do not use this product near water, for example, in a wet basement or near a swimming pool.
Avoid using this product during an electrical storm. There may be a remote risk of electric shock
from lightning.
Regulatory Information
Radio Frequency Notifications
Belgique Dans le cas d'une utilisation privée, à l'extérieur d'un bâtiment, au-dessus d'un espace
public, aucun enregistrement n'est nécessaire pour une distance de moins de 300m. Pour une
distance supérieure à 300m un enregistrement auprès de l'IBPT est requise. Pour une utilisation
publique à l'extérieur de bâtiments, une licence de l'IBPT est requise. Pour les enregistrements
et licences, veuillez contacter l'IBPT.
France 2.4 GHz Bande : les canaux 10, 11, 12, 13 (2457, 2462, 2467, et 2472 MHz
respectivement) sont complétement libres d'utilisation en France (en utilisation intérieur). Pour ce
qui est des autres canaux, ils peuvent être soumis à autorisation selon le départment.
L'utilisation en extérieur est soumis à autorisation préalable et trèsrestreint. Vous pouvez
contacter l'Autorité de Régulation des Télécommunications (http://www.art-telecom.fr) pour de
plus amples renseignements.
5850 Series QolorPIX Tape Controller
6
3
Introduction
City Theatrical's QolorPIX Tape Controller is an innovative approach to pixel control which
offers a high level of creativity combined with plug and play usability. Each QolorPIX Tape
Controller is preconfigured with personality profiles, which can be combined and tuned to
produce thousands of dynamic effects using only a few DMX channels. Chases, fades, scrolls,
bursts, and other effects can be created and saved as needed. QolorPIX Pixel Controlled LED
Tape connects to the controller using industry standard four pin XLR connectors. Within one
minute, the system can be up and running.
3.1
Features
□
Supports ANSI E1.11 DMX512-A
□
Compatible with City Theatrical QolorPIX Pixel Controlled LED Tape
□
Effects engine enables controlling entire length of QolorPIX tape with only 16 or
32 DMX addresses per five meter reel of tape
□
Eight output ports individually addressable
□
Up to 240 individual pixels on each port
□
Firmware is user updatable through micro-SD card slot
□
Tape is controllable via DMX512-A, recordable presets, and test routine
□
DMX512 control through effects engine, RGB, and pixel address modes
□
Can be mounted in a standard 19-inch rack with included mounting accessories.
Requires 2U rack spaces.
5850 Series QolorPIX Tape Controller
7
3.2
What’s Included
Figure 1: What's Included
1. QolorPIX Tape Controller
2. Set of Mounting Plates
3. 8’ NEMA 5-15p to Neutrik powerCON TRUE1 Cable
4. Antenna, 2 dBi Omni Swivel 2.3”
5.
Fasteners (four in total)
3.3
Customer Service
City Theatrical, Inc.
475 Barell Avenue
Carlstadt, NJ 07072
Phone: (800) 230-9497 / (201) 549-1160
Fax: (201) 549-1161
support@citytheatrical.com
City Theatrical LTD.
Office 31, Units 1-3 Wyvern Estate
Beverly Way, New Malden, Surrey
KT3 4PH United Kingdom
Phone: +44 (0) 20 8949 5051
For additional resources and documentation, please visit our website at: www.citytheatrical.com
1.
4.
2.
2.
5.
5.
3.
5850 Series QolorPIX Tape Controller
8
4
Specifications
4.1
Specifications
Table 1: Physical Characteristics
Specification
Description
Size
7.8” L(198mm) x 13.6” W (345mm) x 3.45” H (88mm)
Weight
5.75 lbs (2.61Kg)
Connections
- Neutrik powerCON TRUE1 Power in and through 20A
- 5-pin DMX512 in and through ports
- 8 x XLR 4-pin output ports
- RP-SMA female antenna connector
Fuse
3AG type 10A/250V Fast-Blow located on front panel
Input Power
115/230VAC, 3.5/1.8A
Inrush Current
35/70A
Output Power
5VDC, 6A max per port
Output Class
Class 1
Pixels
1 to 240 per port
Storage Temperature
-20° C to 85° C
Operating Temperature
0° C to 40° C
4.2
Mounting
Figure 2: Pipe Mount
5850 Series QolorPIX Tape Controller
9
Figure 3: Rack Mount
Figure 4: Surface Mount
4.3
Air Flow
Figure 5: Air Flow
5850 Series QolorPIX Tape Controller
10
4.4
Face Panel
AC Thru
and AC IN
Figure 6: Face Panel
4.5
Output Port Pinout
The output ports on the QolorPIX Tape Controller
use a Neutrik 4-pin Female connector. Pixel tape
should be wired with a 4-pin male connector with
pin 1 connected to common, pin 3 connected to
data, and pin 4 connected to the +5v line. Pin 2 is
not currently used. Make sure the wire gauge
used for pins 1 and 4 is large enough to avoid
dimming due to voltage drop. Typical scroller
cable uses 14awg wires on these pins. Double
check connections before connecting pixel tape
to QolorPIX controller.
Incorrect wiring can cause permanent damage
to the pixel tape or controller port. The QolorPIX
Controller pinout is compatible with typical 4-pin
scroller cable.
Ports 1 Through 4
DMX
DMX Data
IN LED
Antenna
LED Display
Power LED
Micro SD
Card Slot
Ports 5 Through 8
DMX Thru
User Controls
Figure 7: Pinout
5850 Series QolorPIX Tape Controller
11
5
Configuration
5.1
Installation
The QolorPIX Tape Controller requires standard AC power from 90-260V, 50/60 Hz. The front
panel provides an AC in and through connection via Neutrik powerCON TRUE1.
Mounting accessories are included to provide mounting with two c-clamps or in a typical 19-inch
rack. The QolorPIX Tape Controller uses 2U mounting spaces.
When unit is installed ensure that the air vents on either side of the box are not covered.
If unit is being controlled via DMX512 ensure that the last unit in the chain is properly terminated
with a 120Ω ½ watt resistor between pins 2 and 3. A DMX connector with a built in terminating
resistor is available from your local distributor.
5.2
Menu
To lock the menu, press and hold both the "Up" and "Down" buttons for two seconds until
"LOCKED" is displayed.
To unlock the menu, press and hold both the "Up" and "Down" buttons for two seconds until
"UNLOCKED" is displayed.
5.3
Menu Descriptions
5.3.1
Save
The “Save” menu option will save any configuration changes since last power on.
If configuration changes are not explicitly saved, they will be lost on power off.
Changes made through RDM are automatically saved.
5.3.2
Restore
The “Restore” menu option can be used to reset the device configuration to factory defaults.
5.3.3
Port Settings
The “Port Settings” menu option allows you to configure each port. Changes can be
made globally or individually by port. Only changed values are applied. For example, you
can change the number of pixels of every port without changing any of the ports’
addresses.
5850 Series QolorPIX Tape Controller
12
Port Settings Mode
Settings marked in RED have not been saved in persistent memory and will be lost when power
is turned off. Use the “Save” menu option to retain these changes.
5.3.3.1
Product
This can be used to select the QolorPIX product to use with the output port. At this time
the only choice is “QP48” for standard City Theatrical QolorPIX tape.
5.3.3.2
Pixels
Used to identify the number of QolorPIX connected to the port. This can be any
value from 1 to 240.
5.3.3.3
Scale
Scale assigns a single pixel attribute to 1, 2, or 3 consecutive pixels. This allows
effects and direct pixel mapping to be scaled up when a larger visible effect is
desired.
5.3.3.4
Mode
The QolorPIX Tape Controller can be run in the following modes:
□
16 Channel
□
32 Channel
(uses two layers of effects)
□
RGB
(3 Channel) Treats entire length of tape as an RGB fixture.
□
MAP
addresses each LED as a 3 Channel fixture starting with the pixel
closest to the QolorPIX Tape Controller.
□
(P1-P4)
Playback of pre-recorded presets.
5.3.3.5
Port Address
Set the starting address of the port(s) for DMX controlled modes.
5.3.3.6
Master Dimmer
Set a master dimmer address for the entire port(s). Leave at “0” for none. It does not
need to be sequential with the personality address. It can be the same for multiple ports
even if they are set to different personality addresses.
5.3.3.7
Fixture ID
Not presently implemented.
5.4.3.8 Direction
Sets which end of the tape the effects originate from. It is helpful if different segments
of tape are run in opposite directions.
5850 Series QolorPIX Tape Controller
13
5.3.4
Create Presets
Create presets allow the user to create up to four presets, which can be arbitrarily assigned
for playback to any given port. The menu gives the option to create the presets in two
different ways: “Capture DMX” and “Manual Levels.” When using “Capture DMX,” the
QolorPIX Tape Controller takes a snapshot of the incoming DMX channels 1 through 32 and
assigns those levels to the selected preset. When using “Manual Levels,” the QolorPIX Tape
Controller allows the user to manually set the present’s channel value directly from the unit’s
display. Values in “Manual Levels” range from zero to 255 (are not listed as percentages).
Presets will not be retained when power is lost unless “Save” is executed from the Main
Menu.
Usage example of “Capture DMX”:
□
Go to Port 1 Settings and set the “Mode” to “32Ch” and “Port Address” to 1. (All presets
must be recorded at address 1.)
□
Send a DMX signal and adjust channels one through 32 to create and tweak the
desired effect. The pixel Controlled LED tape on Port 1 can be used to visually verify
the effect being created.
□
Go to “Create Presets.”
□
Select the desired preset.
□
Select Capture DMX.
□
Assign the created preset to any port by changing the “Mode” option in the Port
Settings.
Using example of “Manual Levels”:
□
Go to Port 1 Settings and set the “Mode” to “P1.”
□
Go to “Create Presets.”
□
Select the Preset 1.
□
Select Manual Levels.
□
Adjust the values of the various channels to create and tweak the desired effect. The
changes will be reflected on the pixel tape connected to Port 1.
□
Assign the created preset to any port by changing the “Mode” option in the Port
Settings.
5850 Series QolorPIX Tape Controller
14
5.3.5
Test Mode
Test mode allows enabling of the test pattern (alternating blue and yellow wipes) for one or all
ports.
5.3.6
Advanced
5.3.6.1
Flicker Finder
Flicker Finder shows current input levels for a full 512 slots of DMX data. Red bars
show the maximum received value to assist with visualizing flickering input data. The
upper segment shows the incoming DMX refresh rate (number of full DMX frames
received per second). The up and down arrows can be used to display information
about individual channels. It shows the current DMX value along with the minimum and
maximum values seen since Flicker Finder was initiated.
To identify flickering in a DMX line, set the controlling console or tester to a static look
and enter the Flicker Finder menu item to visualize unexpected changing values. DMX
flicker can be caused by poor or broken cables, misbehaving devices in the DMX chain,
or improper DMX termination.
5.3.6.2
Update Firmware
Firmware updates for the QolorPIX Tape Controller are available in the “Downloads”
tab of the QolorPIX Tape Controller product page at:
http://www.citytheatrical.com/Products/qolorpix-tape-controller-eight-output
The Update Firmware option will flash new firmware to the QolorPIX Tape Controller
from an installed MicroSD card. Copy the new firmware files onto the micro SD card,
insert it in the QolorPIX Tape Controller, cycle power on the controller, then select
“Update Firmware” from the menu. Press “Enter” when prompted to confirm. The
firmware update process will check for valid update files and push them to the
appropriate ports of the controller.
5850 Series QolorPIX Tape Controller
15
1515
6
DMX Characteristics
6.1
DMX Maps
Table 2: 16-Channel DMX Map
DMX
Address
Description
Notes
1
Intensity
2
Red 1
Background or secondary effect color
3
Green 1
4
Blue 1
5
Red 2
Primary effect color
6
Green 2
7
Blue 2
8
Effect Select
See Table 3: Effect List
9
Size
Increases the size of certain effects.*
10
Color Mix
Mixes effect and background colors or increases
trough height, depending upon the effect.*
11
Rate 1
Increases the speed of bulb decay for certain effects.*
12
Rate 2
Increases the speed of rotation, sweep, or scan
movement, or increases rate of beats or strobe,
depending on the selected effect.*
13
Density
Increases the density of bulbs (maximum number
of bulbs that can fill the strip at one time) or
increases the amount of strobe for certain effects.*
14
Direction
Changes which end of the tape the effect originates
from or mirrors the effect in from the ends or out
from center for certain effects.*
15
Repeat
Repeats the selected effect pattern by two, four,
eight, 16 or 32 times, for certain effects.*
16
Origin Offset
Rotates the starting point of the effect along the
pixel tape for certain effects.*
*
See Table 3: Effect List, for which effects can be altered using this parameter.
DMX Address:
5850 Series QolorPIX Tape Controller
Table 3: Effect List
Size Rate
8
9
10
11
12
13
14
15
16
DMX
Value
Pre-Built Effect
Variation
Size
Color Mix
Rate 1
Rate 2
Density
Direction
Repeat
Origin Offset
0
Static Color
1
One Color Paparazzi
Snap On / Snap Off
2
One Color Paparazzi
Fade On / Fade Off
Size of Bulb
(ranges from 1-13
Pixels)
Color Mix
(mixes
background into effect
color in fade effect)
Speed of Bulb
Decay
(ranges from
slow to fast; faster
speeds make new
bulbs appear faster)
Speed of
Rotation (ranges
from slow to fast)
Density of Bulbs
(ranges from low to
high density; alters
maximum number of
bulbs that can fill the
strip)
Origin Offset
(increases the starting
point of the effect
origin)
3
Two Color Paparazzi
Snap On / Snap Off
4
Two Color Paparazzi
Fade On / Fade Off
5
6
Comet
Comet
Uniform Color
Uniform Decay
Size of Comet
(ranges from small to
large)
Color Mix
(mixes
background color into
effect color in fade
effect)
Speed of
Rotation (ranges
from slow to fast; faster
comets have longer
tails)
7
Jockey
Size of Jockey
(ranges from 1-31
Pixels)
8
Checkers
Speed of
Rotation (ranges
from slow to fast)
Direction of
Rotation
(Forward is
0-62, Reverse is 63-
127, Mirror In is 128-
191, Mirror Out is 192-
255)
Origin Offset
(increases the starting
point of the effect
origin)
9
Color Merge
Size of Merge
(ranges from 0-100%)
Color Mix
(mixes
background color into
effect color in fade
effect)
Pattern Repeat
(2x is 1-63, 4x is 64-
127, 8x is 128-195, 16x
is 196-254, 32x is 255)
10
11
Wave
Wave
Uniform Color
Uniform Decay
Size of Wave
(ranges from 0-100%)
12
Sweep
Continuous
Size of Sweep
Step
(ranges from 1-
8 Pixels)
Speed of Sweep
(ranges from slow to
fast, altering speed at
the sweep move)
13
Sweep
Random Start Delay
14
Index Wipe
Size of Wipe
(ranges from 0-100%)
Origin Offset
(increases the starting
point of the effect
origin)
15
VU
Manual (Solid Color -
No Peak Hold)
Peak Height
(ranges from 0-100%)
16
17
VU
VU
Random Height
(Solid Color - No
Peak Hold)
Height Index (Solid
Color - No Peak
Hold)
Base Height
(ranges from 0-100%)
Rate of Beats
(ranges from 0-600
BPM)
Peak Height
(ranges from 0-100%)
18
Strobe
Rate of Strobe
(ranges from 0-10
FPS)
Duty Cycle (ranges
from 1-100%;
increases amount of
time Strobe is on per
cycle)
19
KnightRider
Uniform Color
20
KnightRider
Uniform Decay
Size of Scanner
(ranges from 0-100%)
Speed of Scan
Movement (ranges
from slow to fast)
Direction of
Rotation
(Forward is
0-62, Reverse is 63-
127, Mirror In is 128-
191, Mirror Out is 192-
255)
Pattern Repeat
(2x is 1-63, 4x is 64-
127, 8x is 128-195, 16x
is 196-254, 32x is 255)
Origin Offset
(increases the starting
point of the effect
origin)
21
Police Strobe
Snap On / Snap Off
Rate of Strobe
(ranges from 0-10
FPS)
Key:
= Effect can be adjusted with the selected parameter (by changing the DMX value for selected DMX Address to a value between 0 and 255).
= Effect cannot be adjusted with the selected parameter.
16
5850 Series QolorPIX Tape Controller
17
7
Troubleshooting
Table 4: Troubleshooting Guide
Symptom
Solution(s)
Refer to…
Unit does not power up.
Check that power cable is properly installed and that
the Neutrik powerCON TRUE1 connector is turned
to its locked position.
Installation
Test power outlet with another device.
Pixel tape does not light up.
Run a test routine to see if tape is working properly.
Test Mode
Check tape for correct pinout.
Pinout
Pixel tape is not responding
to DMX.
Is the front panel DATA led solid indicating that data is
present?
Color shift at end of tape.
Try reducing the tape length, as this is typically due to
overload.
Flashing.
Correct overload short, as this is typically due to
output port short and active safety circuit protection.
5850 Series QolorPIX Tape Controller
18
Table 5: Accessories
Part Number
Description
Q5050-5-RGB-48-5-67-2
QolorPIX Pixel Controlled LED Tape, black, with
4-pin XLR – 5 meter reels
5870
QolorPIX Rack Mount / Pipe Mount Ears
with Fasteners
5840
8’ NEMA 5-15p to powerCON TRUE1 Cable
5729
Antenna, 2 dBi Omni Swivel 2.3”
5891
Four Pin XLR with three Conductor 6” Tail
6691
Aluminum Extrusion, 2m, 21mm x 9mm (15mm inside)
6692
Aluminum Extrusion, 2m, 21mm x 14mm (16mm inside)
6696
Diffuser, 2m, for 6691 Extrusion
6697
Diffuser, 2m, for 6692 Extrusion
8 Accessories
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
