Esoteric K-05XD Le manuel du propriétaire

Marque: Esoteric

Modèle: K-05XD

Catégorie: Lecteur CD

Taper: Le manuel du propriétaire

K-05XD

OWNER’S MANUAL.....................3

MODE D’EMPLOI .......................33

MANUAL DEL USUARIO ...........63

Super Audio CD/CD Player

D01395321B

English

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

<The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

BThe exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

oDO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

oIF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR

A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS

BEEN REPAIRED.

oUSE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is

used, use caution when moving the cart/

apparatus combination to avoid injury from

tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

oThe apparatus draws nominal non-operating power from the AC

outlet with its POWER or STANDBY/ON switch not in the ON position.

oThe mains plug is used as the disconnect device; the disconnect

device shall remain readily operable.

oCaution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume) from

earphones or headphones can cause hearing loss.

WARNING

Products with Class ! construction are equipped with a power

supply cord that has a grounding plug. The cord of such a prod-

uct must be plugged into an AC outlet that has a protective

grounding connection.

IN USA/CANADA, USE ONLY ON 120V SUPPLY.

CAUTION

oDo not expose this apparatus to drips or splashes.

oDo not place any objects filled with liquids, such as vases, on

the apparatus.

oDo not install this apparatus in a confined space such as a

book case or similar unit.

oThe apparatus should be located close enough to the AC

outlet so that you can easily reach the power cord plug at any

time.

oIf the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine,

fire or excessive heat.

oCAUTION for products that use replaceable lithium batteries:

there is danger of explosion if a battery is replaced with an

incorrect type of battery. Replace only with the same or equiva-

lent type.

IMPORTANT SAFETY INSTRUCTIONS (continued)

V Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading to

fire, injury or the staining of nearby things. Please read and observe

the following precautions carefully.

oBe sure to insert the batteries with correct positive (¥) and nega-

tive (^) orientations.

oUse batteries of the same type. Never use different types of batter-

ies together.

oIf the remote control is not used for a long time (more than a

month), remove the batteries to prevent them from leaking.

oIf the batteries leak, wipe away the leakage inside the battery

compartment and replace the batteries with new ones.

oDo not use batteries of types other than those specified. Do not

mix new batteries with old ones or use different types of batteries

together.

oDo not heat or disassemble batteries. Never throw batteries into

fire or water.

oDo not carry or store batteries with other metallic objects. The bat-

teries could short circuit, leak or explode.

oNever recharge a battery unless it is confirmed to be a recharge-

able type.

oDo not expose batteries to extremely low air pressure as it could

result in an explosion or leakage of flammable liquids or gases.

Laser information

This laser product is a consumer laser product according to

EN50689:2021 and complies with all consumer laser product require-

ments except child appealing products.

This product contains a laser system and is classified as a CLASS 1

LASER PRODUCT according to IEC60825-1:2014. This class does not

require special attention in normal use. Do not take apart to prevent

being exposed to the laser beam.

Laser:

Type: RLD2WMFR1

Manufacturer: ROHM Co.,Ltd.

Laser output: Less than 0.7mW on the objective lens

Wavelength: 790 ±15nm (CD)

650 ±10nm (Super Audio CD)

Model for USA

This product has been designed and manufactured according to

FDA regulations “title 21, CFR, chapter 1, subchapter J, based on the

Radiation Control for Health and Safety Act of 1968”, and is classified

as class ! laser product. There is not hazardous invisible laser radiation

during operation because invisible laser radiation emitted inside of

this product is completely confined in the protective housings.

The label required in this regulation is as follows:

Supplier’s Declaration of Conformity

Model number: K-05XD

Trade name: ESOTERIC

Responsible party: 11 Trading Company, LLC

Address: 3502 Woodview Trace #200 Indianapolis, IN 46268 U.S.A.

URL: https://11tradingcompany.com/contact-us/

This device complies with Part.15 of FCC Rules.

Operation is subject to the following two conditions:

1) This device may not cause harmful interference

2) This device must accept any interference received, including

interference that may cause undesired operation.

Information

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equip-

ment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the equipment and/or the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

Model for Canada

Innovation, Science and Economic Development Canada’s

Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-003.

Model for Europe

This product complies with the European

Directives request, and the other Commission

Regulations.

Model for UK

This product complies with the applicable UK

regulations.

English

For European Customers

Disposal of electrical and electronic equipment and

batteries and/or accumulators

a) All electrical/electronic equipment and waste batteries/accu-

mulators should be disposed of separately from the municipal

waste stream via collection facilities designated by the govern-

ment or local authorities.

b) By disposing of electrical/electronic equipment and waste

batteries/accumulators correctly, you will help save valu-

able resources and prevent any potential negative effects on

human health and the environment.

c) Improper disposal of waste electrical/electronic equipment

and batteries/accumulators can have serious effects on the

environment and human health because of the presence of

hazardous substances in the equipment.

d) The Waste Electrical and Electronic Equipment (WEEE)

symbols, which show wheeled bins that have been

crossed out, indicate that electrical/electronic equip-

ment and batteries/accumulators must be collected

and disposed of separately from household waste.

If a battery or accumulator contains more than the

specified values of lead (Pb), mercury (Hg), and/or

cadmium (Cd) as defined in the Battery Directive

(2006/66/EC, 2013/56/EU), then the chemical symbols

for those elements will be indicated beneath the WEEE symbol.

e) Return and collection systems are available to end users. For

more detailed information about the disposal of old electri-

cal/electronic equipment and waste batteries/accumulators,

please contact your city office, waste disposal service or the

shop where you purchased the equipment.

Pb, Hg, Cd

“DSD” is a registered trademark.

“Super Audio CD” is a registered trademark.

This product incorporates copy protection technology that is protected

by U.S. patents and other intellectual property rights of Rovi Corporation.

The use of Rovi Corporation’s copy protection technology in the product

must be authorized by Rovi Corporation.

Reverse engineering and disassembly are prohibited.

Microsoft and Windows are either registered trademarks or trade-

marks of Microsoft Corporation in the United States and/or other

countries.

Apple, Mac, OS X and macOS are trademarks of Apple Inc., registered

in the U.S. and other countries.

Bulk Pet is a registered trademark of INTERFACE CO., LTD.

ESOTERIC is a trademark of TEAC CORPORATION, registered in the U.S.

and other countries.

Other company names, product names and logos in this document

are the trademarks or registered trademarks of their respective owners.

Contents

IMPORTANT SAFETY INSTRUCTIONS ...............................3

Before use .........................................................6

Precautions for use ................................................7

Notes about discs .................................................8

Connections ....................................................... 9

Notes about the remote control ..................................12

Remote control parts and functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Main unit parts and functions .....................................14

Display parts and functions .......................................15

Playback ..........................................................16

Selecting tracks ...................................................18

Playback modes ..................................................19

Repeat playback ..................................................20

Display ...........................................................20

Dimmer ..........................................................21

Changing the input source .......................................21

Connecting with a computer and playing back audio files ........22

Setting mode .....................................................24

MENU1 ..........................................................25

MENU2 ..........................................................27

MQA (Master Quality Authenticated) ..............................28

Troubleshooting ..................................................28

Specifications .....................................................31

Dimensional drawings ............................................32

Thank you for purchasing this ESOTERIC product.

Read this manual carefully to get the best performance from this

product. After reading it, keep it in a safe place with the warranty card

for future reference.

ATTENTION

This unit outputs analog and digital signals only from the

currently selected analog and digital connector types.

Before use, make the analog and digital output settings.

See “Setting mode” on page24 and “Analog output set-

ting” and “Digital output setting” on page25.

Before use

Included accessories

Check to be sure the box includes all the supplied accessories shown

below. Please contact the store where you purchased this product if

any of these accessories are missing or have been damaged during

transportation.

Power cord × 1

Remote control (RC-1333) × 1

Batteries for remote control (AA) × 2

Felt pads × 3

Owner’s manual (this document) × 1

Warranty card × 1

Note about pinpoint feet

High-precision metal pinpoint feet are attached to the bottom plate

of this unit.

The pinpoint feet and their stands are loose, but when the unit is

placed in position, it is supported by these pinpoint feet, which effec-

tively disperse vibrations.

Chassis

Pinpoint foot (metal)

Foot-stand (metal)

After

placement

oIf there is a gap between a chassis and a pinpoint foot after place-

ment, turn the pinpoint foot in the direction that tightens the

screw to eliminate the gap.

oApply the included felt pads to the bottoms of the foot-stands to

avoid scratching the surface where the unit is placed.

oThis unit is very heavy, so take care to avoid injury during installation.

English

oThis unit is very heavy, so take care to avoid injury during installation.

oDo not install this unit in a location that could become hot. This

includes places that are exposed to direct sunlight or near a radia-

tor, heater, stove or other heating equipment. Moreover, do not

place it on top of an amplifier or other equipment that gener-

ates heat. Doing so could cause discoloration, deformation or

malfunction.

oIn order to enable good heat dissipation, leave at least 20cm (8")

between this unit and walls and other equipment when installing

it. If you put it in a rack, take precautions to prevent overheating by

leaving at least 5cm (2") open above and 10cm (4") open behind it.

Failure to provide these gaps could cause heat to build up inside

and result in fire.

oIf installing in a rack with a glass door, do not use the remote con-

trol tray open/close (-) button to open the disc tray when the

door is closed. If the disc tray is forcibly prevented from moving,

damage could result.

oPlace the unit in a stable location.

oDo not place anything on top of the unit.

oDo not lift or move the unit during playback because the disc

rotates at high speed. Doing so could damage the disc.

oAlways remove any loaded disc before moving this unit or pack-

ing it for installation in a different location, for example. Moving

the unit with a disc inside could cause damage.

oThe voltage supplied to the unit should match the voltage as

printed on its back. If you are in any doubt regarding this matter,

consult an electrician.

oDo not open the body of the unit as this might result in damage

to the circuitry or cause electric shock. If a foreign object should

get into the unit, contact your dealer.

oWhen removing the power plug from an outlet, always pull

directly on the plug. Never pull on the cord itself.

Precautions for use

Precaution when recording with a connected

device

Some discs include signals to prevent copying. You cannot record the

digital audio signal as is from a disc that has such copy-protection.

(You can record the audio as an analog signal.)

Maintenance

Use a soft dry cloth to wipe the surface of the unit clean.

For stubborn smudges, use a damp cloth that has been thoroughly

wrung out to remove excess moisture.

oNever spray liquid directly on this unit.

oDo not wipe with chemical cleaning cloths, thinner or other

chemical agents. Doing so could damage the surface.

oAvoid allowing rubber or plastic materials to touch the unit for

long periods of time because they could damage the cabinet.

For your safety, disconnect the power cord from

the outlet before cleaning.

Handling discs

oLoad discs with their labeled sides up.

(CDs only have one playable side.)

oTo remove a disc from its case, always press down on the center of

the case first and then hold the disc by its edges.

Removal from case Holding by edges

oBe careful when handling discs. If the side that contains the data

(unlabeled side) is scratched, smudged with fingerprints or other-

wise dirty or marred, errors could occur during playback.

oIf the side of the disc that has the data encoded on it (unlabeled

side) becomes dirty with fingerprints or dust, use a soft cloth to

wipe the surface from the center directly toward the edge.

Always clean discs before storing them. Leaving a disc in an

unclean state might degrade its sound quality.

oNever use record cleaners, antistatic treatments, thinners or similar

chemicals to clean discs. Such chemicals could harm the surface

of the disc.

oDo not leave discs in places that are exposed to direct sunlight or

that are very humid or hot.

oWhen writing something on the label side of a disc, use a felt-tip

permanent marker. The use of a ballpoint pen or other pen with a

hard tip could damage the disc, making it unplayable.

oAfter you finish playing a disc, always put it back into its case for

storage. Failure to do so could result in warping or scratches.

oDo not apply labels or other materials to discs. Do not use a disc

that has sticky residue left on its surface after removing tape or a

sticker, for example. If such a disc is loaded, it might become stuck

in the unit or damage the unit.

Notes about discs

The following marks appear on disc labels and disc cases. This unit

can play discs that have these marks without using an adapter.

This unit cannot play discs that do not have these marks.

Types of discs that can be played on this unit and

their marks

Super Audio CD

Audio CD

If you try to play any other type of disc with this unit, loud

noises that could damage speakers or harm hearing might

occur. Never try to play any type of disc other than those

shown above.

oThis unit cannot play DVD video, DVD audio, video CD, DVD-ROM

and CD-ROM discs, for example.

oThis unit might not be able to properly play Dual Discs, Copy

Control CDs or other special CDs that do not conform to the

Red Book CD standard. Operation and sound quality cannot be

guaranteed when special discs are used in this unit. If playback of

a special disc should cause trouble, contact the seller of the disc.

CD-R/CD-RW discs

This unit can play CD-R/CD-RW discs that are in audio CD format.

oBe sure to finalize discs created by CD recorders.

Depending on the quality of the disc and the condition of the

recording, playback might not be possible. For details, see the

operation manual for the device you are using.

English

oNever use commercially-available CD stabilizers. Doing so could

make the disc unplayable or damage the unit.

oDo not use cracked discs because they could damage the unit.

oNever use discs with irregular shapes, including heart-shaped and

octagonal discs, because they could damage the unit.

oDo not use printable discs, which allow printing on the label

side. Since the surface of such a disc has been specially treated, if

loaded, it might become stuck in the unit or damage the unit.

If you have any questions about how to handle a CD-R or CD-RW

disc, contact the manufacturer of the disc directly.

Connections

Connecting using ES-LINK Analog

ESL-A

Amplifier with ES-LINK

Analog (ESL-A) connectors

XLR cables

ES-LINK Analog

(ESL-A) connectors

Use XLR cables to connect the analog audio output (XLR/ESL-A) con-

nectors on this unit to an amplifier that has ES-LINK Analog (ESL-A)

connectors.

oSet this unit’s analog output (AOUT>) to ESLA.

oNormal XLR and RCA connections are also possible. Select the

connection type that provides the audio quality you prefer.

ES-LINK Analog overview

The current transmission method utilizes the performance of HCLD

buffer circuits that feature the ability to supply strong current at high

speed. This suppresses the impact of impedance on signal paths,

enabling pure and powerful transmission of signals.

oUse connection cables that are shielded and balanced.

oOrdinary balanced cables (with XLR connectors) are used for

connection. These connectors can only be used with compatible

devices, however, because the transmission format is unique.

Connections (continued)

V Precautions when making connections

oComplete all other connections before connecting the power plug to a power outlet.

oRead the owner’s manuals of all devices that will be connected, and follow their instructions.

Digital output can be set to XLR or

COAX (page25).

The polarity of the XLR connectors

can be set so that either 2 or 3 is

HOT (page25).

RCA cables

XLR cables

USB cable

Connect using a set of

only one type.

Set the analog output

setting (AOUT>) to the

connector type being

used (page25).

RCA coaxial digital

cable

Optical digital

cable

Included power cord

RCA coaxial digital

cable

BNC coaxial cable

Stereo amplifier

ComputerOther digital devices

(DA converter, AV amplifier,

recorder, etc.)

Equipment with

digital audio

output

Equipment with

digital audio

output

Device that outputs

clock signal (G-01X, etc.)

DIGITAL IN

(COAXIAL)

DIGITAL IN

(XLR)

DIGITAL OUT

(COAXIAL)

DIGITAL OUT

(OPTICAL)

10MHz OUT

Audio input

(LINE IN, etc.)

XLR digital cable

Wall outlet

English

A Analog audio output (LINE OUT) connectors

These output 2-channel analog audio. Connect the XLR or RCA

connectors to an amplifier.

Use commercially-available cables for connections.

XLR/ESL-A: XLR cables

RCA: RCA cables

Connect an R connector on this unit to an R connector on the

amplifier, and connect the corresponding unit L connector to

the corresponding amp L connector.

oSet the analog output to ESLA, XLR2, XLR3, RCA or OFF

(page25).

oWhen connecting this unit with an amplifier that has ES-LINK

Analog (ESL-A) connectors, we recommend connecting the

XLR connectors on this unit to the ES-LINK Analog (ESL-A)

connectors on the amplifier (page9).

B Digital audio input (DIGITAL IN) connectors

Use these to input digital audio. They can be connected to the

digital output connectors of audio devices.

Use commercially-available cables for connections.

COAXIAL: RCA coaxial digital cable

OPTICAL: optical digital cable (TOS)

C Digital audio output (DIGITAL OUT) connectors

These output digital audio signals from CDs played on this unit

and signals input through this unit’s digital audio input (DIGITAL

IN) connectors.

Connect the digital audio output (DIGITAL OUT) connectors on

this unit to the digital audio input connectors of other digital

devices, such as a DA converter, AV amplifier or recorder.

Use commercially-available cables for connections.

XLR: XLR digital cable

COAXIAL: RCA coaxial digital cable

oThese connectors cannot output Super Audio CD digital

audio.

oDigital output can be set to OFF, XLR or COAX (page25).

D SIGNAL GND grounding terminal

The audio quality might be improved by connecting this ground-

ing terminal to an amplifier or other device that is connected to

this unit.

oThis is not a safety grounding terminal.

E AC power inlet (~IN)

Connect the included AC power cord to this AC inlet.

After completing all other connections, plug the power plug

into a power outlet.

Use only a genuine ESOTERIC power cord. Use of

other power cords could result in fire or electric

shock.

Disconnect the power plug from the outlet if you

will not use the unit for a long time.

F 10MHz IN CLOCK connector

Use the 10MHz IN CLOCK connector to input 10MHz clock syn-

chronization signals.

When using clock synchronization, connect the clock output

connector of the device outputting the clock signal to the clock

input connector on this unit. Then, set the external clock (CLK>)

setting to ON (page25).

Use a commercially-available BNC coaxial cable for

connection.

oBNC coaxial cables with 50Ω or 75Ω impedance can be used.

G USB port

Use this to input digital audio from a computer. Connect it to a

computer’s USB port.

Use a commercially-available USB cable for connection.

oBefore connecting, read pages22 and 23.

H SOFTWARE maintenance port

This is used for maintenance. Do not connect anything to this

port unless instructed to do so by our service department.

I Remote control input (RS-232C) connector

This control connector is for use by professionals (custom

installers).

J TRIGGER IN connector

Use this connector to control power from an external source.

Do not connect anything to this connector when not using it.

Notes about the remote control

Precautions when using the remote control

oWhen using the remote control, point it toward the remote con-

trol signal receiver on the main unit from a distance of 7m (23ft)

or less. Do not place obstructions between the main unit and the

remote control.

oThe remote control might not work if the remote control signal

receiver is exposed to direct sunlight or bright light.

oBeware that use of this remote control could cause the unin-

tentional operation of other devices that can be controlled by

infrared rays.

Installing batteries

1 Slide the bottom end of the remote control as

shown in the illustration, and pull out the battery

holder.

2 Insert two AA batteries with ¥ and ^ oriented

as shown in the holder, and put the holder in

again.

3 Slide the bottom end of the remote control as

shown in the illustration to close the battery

holder.

When to replace batteries

If the distance required between the remote and the main unit

decreases or if the main unit stops responding to the remote buttons,

replace both batteries with new ones.

Dispose of the used batteries according to the instructions on them

or requirements set by your local municipality.

Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak, which

might result in fire, injury or the staining of nearby materials.

Please read and observe the precautions on page4 carefully.

English

Remote control parts and functions

When the main unit and the remote control both have buttons

with the same functions, this manual explains how to use one

of the buttons. The other corresponding button can be used in

the same manner.

a DISPLAY button

During playback or when paused, press this button to change

what is shown on the display (page20).

b Skip (.//) buttons

Use these to skip to the previous or next track.

Press and hold these during playback to search backward/for-

ward. Repeatedly press and hold these to change the backward/

forward search speed (page18).

Use these to change parameters when in setting mode.

c Stop (8) button

Press this to stop playback.

Press this when in setting mode to complete changing settings

and return the display to normal (page17).

d PLAY AREA button

When stopped, press this to change the playback area of a Super

Audio CD (page17).

e REPEAT button

Use this for repeat playback (page20).

f MODE button

Press this to change the input source (page21).

Press and hold this to enter setting mode (page24).

g Tray open/close (-) button

Press this to open and close the disc tray.

h Play (7) button

Press this to start disc playback.

i Pause (9) button

Press this to pause playback.

Press this when paused to start playback.

j AMP buttons

These buttons are not used with this unit. They can be used with

ESOTERIC amplifiers.

k ON/STANDBY buttons

Use these to turn the unit on or put it into standby mode.

l Number buttons

Use these for track selection and program playback (pages18

and 19).

m DIMMER button

Use this to adjust the brightness of the main unit’s display

(page21).

n PLAY MODE button

Press this to switch between program and shuffle playback

modes (page19).

Main unit parts and functions

A STANDBY/ON button

Press this to turn the unit on or put it into standby mode.

When the unit is on, the ring around the button lights.

When the unit is off, it is unlit.

When not using the unit, put it into standby mode.

B CLOCK indicator

This shows the clock synchronization status.

This indicator blinks during clock synchronization and lights

when synchronization completes.

C MODE button

When stopped, press this button to change the input source.

When set to external input, the unit can be used as a D/A con-

verter (page21).

Press and hold this to enter setting mode (page24).

D Remote control signal receiver

This receives signals from the remote control. When using the

remote control, point the end of it toward this receiver panel

(page12).

E Disc tray

Load a disc for playback here (page16).

F Display

This shows the playback time, the number of tracks and other

information (page20).

G Tray open/close (-) button

Press this to open and close the disc tray.

H Stop (8) button

Press this to stop playback (page17).

When stopped, press and hold this to change the playback area

of a Super Audio CD (page17).

Press this when in setting mode to complete changing settings

and return the display to normal (page24).

I Play (7) button

Press this to start disc playback (page16).

During playback, the indicator next to this button lights.

J Pause (9) button

Press this to pause playback (page17).

When paused, the indicator next to the play button blinks.

K Skip (.//) buttons

Use these to skip to the previous or next track.

Press and hold these during playback to search backward/for-

ward. Repeatedly press and hold these to change the backward/

forward search speed (page18).

Use these to change parameters when in setting mode

(page24).

C D E JK

BH I

English

Display parts and functions

a Input source

When the input source is CD/SACD

This shows the type of disc that is currently loaded.

SACD: Super Audio CD

CD: Audio CD

oWhen a hybrid Super Audio CD is loaded, the playback area

type is shown (page17).

When the input source is COAXin/OPTin/USBin

This shows the input source name.

When the menu is open

This shows “MENU1” or “MENU2” according to the menu item

being set.

b Playback mode

When the input source is CD/SACD

This shows the playback/repeat playback mode (pages19 and

20).

When the input source is USBin

“Bulk Pet” will be shown when it is in use.

c Information

During Super Audio CD playback or DSD signal input

“DoP” will be shown during DoP playback when a DSD signal is

being input.

Then, the DSD filter setting will be shown (page27).

During CD playback or PCM signal input

This shows the digital filter setting (PCMF>) during PCM play-

back (page25).

During MQA-CD playback

This shows MQA information.

d Clock mode

This shows the external clock setting (page25).

No indicator:

When CLK is set to OFF

CLK10M:

Shown when CLK is set to ON

e Analog output setting

This shows the analog output setting (page25).

Nothing appears when set to OFF.

f Message area

The playback time and various messages appear here.

SACD

ESLA

DSD FLT OFFClock

10M

Playback

1 3 4

1 Press the STANDBY/ON button to turn the unit

on.

Keep pressing and holding until the ring around the STANDBY/

ON button lights.

oAutomatic power saving (APS>) is set to OFF when shipped

new from the factory (page26).

2 Press the tray open/close (-) button.

The disc tray comes forward.

3 Place a disc centered on the tray with the labeled

side up.

oIf the tray is closed while a disc is outside the center guides,

the disc might become stuck inside and the tray might not

open. Be sure to always place discs within the guides at the

center of the tray.

4 Press the tray open/close (-) button.

The disc tray closes. Be careful not to let your fingers be pinched

when the tray closes.

oThe unit takes some time to load the disc.

oThe disc playback area can be changed (page17).

5 Press the play (7) button.

Playback starts.

During playback, the indicator near this button lights.

English

Pausing playback

During playback, press the pause (9) button to pause playback.

When paused, the indicator next to the play (7) button blinks.

Press the play (7) or pause (9) button to restart playback.

Stopping playback

Press the stop (8) button to stop playback.

Opening and closing the disc tray

Press the tray open/close (-) button once to open the tray, and

press it again to close the tray.

oIf you press the tray open/close (-) button during disc playback,

several seconds will pass before the tray opens.

Changing the playback area

Press and hold

Some Super Audio CDs have multiple areas, including stereo (2-chan-

nel) and multichannel. Hybrid Super Audio CDs have two layers with

one containing ordinary CD-quality audio.

When stopped, press and hold the stop (8) button to change the

playback area.

oTo change the playback area using the remote control, press the

PLAY AREA button when the unit is stopped.

oThis unit does not support the playback of multichannel areas on

Super Audio CDs.

Selecting tracks

Searching backward/forward

Press and hold

During playback, press and hold a skip (.//) button until

searching backward/forward starts. When you find the point where

you want to listen, press the play (7) button.

You can change the backward/forward search speed by repeatedly

pressing and holding the skip (.//) button.

The speed that the < or > blinks on the display also changes.

/ button

Normal

speed

dSpeed (1) e

Speed (2)

Speed (3)

Speed (4)

. button

Skipping tracks

During playback, press a skip (.//) button to skip to the previ-

ous or next track and start playback.

oPress the . button once to return to the beginning of the current

track. Press the . button repeatedly to return to an earlier track.

If the playback position is less than one second from the begin-

ning of the current track, however, pressing the . button will

skip to the beginning of the previous track.

oWhen stopped or paused, use the skip .// buttons to select

a track and pause at its beginning.

Using the number buttons to select a

track for playback

When playing or stopped, you can press number buttons to select a

track and start playing it back.

To play a track with a single-digit number, press that number button.

To play a double-digit track number, press the +10 button as many

times as necessary, and then press the corresponding number button

for the second digit. After the track number is input, playback starts.

Examples:

Track 7:

Track 23:

English

Changing playback modes

When stopped, press the PLAY MODE button

repeatedly to cycle through the playback modes.

Program playback Shuffle playback

Ordinary playback

oPressing the tray open/close (-) button or main unit STANDBY/

ON button will reset the mode to ordinary playback.

Program playback

You can program up to 24tracks in the order that you want to listen

to them.

1 Set the playback mode to program playback.

2 Use number buttons to select tracks you want

to program.

Examples:

Track 3:

Track 12:

Track 20:

2PGM

Programmed track number Program playback order

Playback modes

To program multiple tracks, continue pressing the number buttons.

oTrack numbers that do not exist on the currently loaded disc

cannot be added to the program.

3 When you are done adding tracks to the pro-

gram, press the play (7) button.

Program playback starts.

oChanging the playback mode will clear the contents of the

program.

Shuffle playback

When the playback mode is set to shuffle, pressing the play (y) button

will play the tracks on the disc in shuffle order.

Repeat playback

During ordinary playback, press the REPEAT button to cycle through

the following repeat playback modes.

REPEAT TRK

(repeat track)

REPEAT DISC

(repeat disc)

REPEAT OFF

(ordinary playback)

During program playback, press the REPEAT button to cycle through

the following repeat playback modes.

REPEAT PGM (repeat program)

3 c

REPEAT OFF (ordinary program playback)

During shuffle playback, press the REPEAT button to cycle through the

following repeat playback modes.

REPEAT SHF (repeat shuffle)

3 c

REPEAT OFF (ordinary shuffle playback)

oStopping playback ends repeat playback mode.

REPEAT TRK

The current track is played back repeatedly. During repeat playback,

select a different track to repeat playback of that track.

REPEAT DISC

All tracks on the current disc are played back repeatedly.

REPEAT PGM

The programmed tracks are played back repeatedly.

REPEAT SHF

Shuffle playback is repeated.

oEvery time all tracks have played back once, their order will be

reshuffled.

Display

During disc playback and when paused, each time the DISPLAY button

is pressed, the information shown on the display changes as follows.

Examples:

Currently playing track Elapsed time of currently

playing track

−2

Remaining time of currently

playing track

Disc elapsed time

−54

Disc remaining time

oWhen stopped, the total number of tracks and total playback time

of the disc are shown.

Example:

:11

Total number of tracks Total disc playback time

La page charge ...

Esoteric K-05XD Le manuel du propriétaire

Marque: Esoteric

Modèle: K-05XD

Catégorie: Lecteur CD

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Esoteric K-05XD Owner's manual
español: Esoteric K-05XD El manual del propietario