CARLO GAVAZZI PD30CTBI20BPM5IO Le manuel du propriétaire

IO-Link

photoelectric sensor

Carlo Gavazzi Industri Over Hadstenvej 40, 8370 Hadsten, Denmark

Instruction manual

Manuel d’instructions

Manuale d’istruzione

Betriebsanleitung

Manual de instrucciones

Brugervejledning

使用手册

PD30CTBxxxBPxxIO

ENGLISH .............................. 3

DEUTSCH ............................ 45

FRANÇAIS ........................... 88

ESPAÑOL ........................... 129

ITALIANO ........................... 170

DANSK ............................. 211

中文第页 ............................ 252

3

EN

Table of contents

1. Introduction ...................................................5

1.1. Description ............................................................. 5

1.2. Validity of documentation ................................................. 5

1.3. Who should use this documentation .......................................... 5

1.4. Use of the product ....................................................... 5

1.5. Safety precautions ....................................................... 5

1.7. Acronyms ............................................................. 6

2. Product ......................................................7

2.1. Main features .......................................................... 7

2.2. Identiﬁcation number ..................................................... 7

2.3. Operating modes ........................................................ 8

2.3.1. SIO mode ....................................................................8

2.3.2. IO-Link mode .................................................................. 8

2.3.3. Process data ..................................................................9

2.4. Output Parameters ..................................................... 10

2.4.1. Sensor front .................................................................11

2.4.1.1. SSC (Switching Signal Channel) ................................................11

2.4.1.2. Switchpoint mode: ..........................................................11

2.4.1.3. Hysteresis Settings ..........................................................13

2.4.1.4. Dust alarm 1 and Dust alarm 2 .................................................13

2.4.1.5. Temperature alarm (TA) ....................................................... 13

2.4.1.6. External input .............................................................13

2.4.2. Input selector ................................................................. 13

2.4.3. Logic function block ............................................................13

2.4.4. Timer (Can be set individually for Out1 and Out2) .......................................15

2.4.4.1. Timer mode ...............................................................15

2.4.4.1.1. Disabled .............................................................15

2.4.4.1.2. Turn On delay (T-on) .....................................................15

2.4.4.1.3. Turn Off delay (T-off) .....................................................16

2.4.4.1.4. Turn ON and Turn Off delay (T-on and T-off) .....................................16

2.4.4.1.5. One shot leading edge ...................................................16

2.4.4.1.6. One shot trailing edge ....................................................17

2.4.4.2. Timer scale ...............................................................17

2.4.4.3. Timer Value ...............................................................17

2.4.5. Output Inverter ...............................................................17

2.4.6. Output stage mode ............................................................17

2.4.7. Application functions ...........................................................18

2.4.7.1. Speed and Length ..........................................................18

2.4.7.1.1. Conditions ............................................................18

2.4.7.1.2. Speed and Length – Setup procedure ..........................................18

2.4.7.2. Pattern Recognition .........................................................19

2.4.7.2.1. Conditions ......................................................19

2.4.7.2.2. Pattern recognition – Setup procedure .........................................19

2.4.7.3. Divider function ............................................................21

2.4.7.3.1. Conditions ............................................................21

2.4.7.3.2. Divider function – Setup procedure ...........................................21

2.4.7.4. Object and Gap Monitoring ...................................................22

2.4.7.4.1. Conditions ............................................................22

2.4.7.4.2. Object and Gap Monitoring – Setup procedure ..................................22

2.5. Sensor Speciﬁc adjustable parameters ....................................... 24

2.5.1. Selection of local or remote adjustment ...............................................24

2.5.2. Trimmer data .................................................................24

2.5.3. Process data conﬁguration .......................................................24

2.5.4. Sensor Measurement Selection ....................................................24

2.5.5. Temperature alarm threshold ......................................................24

2.5.6. Safe limits ...................................................................24

2.5.6.1. Stable ON ...............................................................24

ENGLISH

4

EN

2.5.6.2. Stable OFF ............................................................... 24

2.5.7. Event conﬁguration ............................................................25

2.5.8. Quality of run QoR ............................................................25

2.5.9. Quality of Teach QoT ...........................................................26

2.5.10. Excess Gain ................................................................26

2.5.11. Filter Scaler ................................................................. 26

2.5.12. Mutual interference ...........................................................26

2.5.13. LED indication ...............................................................27

2.5.14. Hysteresis mode .............................................................27

2.5.15. Auto hysteresis value ..........................................................27

2.5.16. Cutoff distance ..............................................................27

2.6. Teach procedure by use of SCTL55 or an IO-Link master .......................... 28

2.6.1. External Teach (Teach-by-wire) .....................................................28

2.6.2. Teach from IO-Link Master or Smart conﬁgurator (SCTL55) .................................28

2.6.2.1. Single point mode procedure ..................................................28

2.6.2.2. Two point mode procedure ....................................................30

2.6.2.3. Windows mode procedure ....................................................31

2.6.2.4. Foreground suppression mode ..................................................32

2.7. Diagnostic parameters ................................................... 33

2.7.1. Operating hours ..............................................................33

2.7.2. Number of power cycles [cycles] ...................................................33

2.7.3. Maximum temperature – all time high [°C] ............................................33

2.7.4. Minimum temperature – all time low [°C] .............................................33

2.7.5. Maximum temperature since last power-up [°C] .........................................33

2.7.6. Minimum temperature since last power-up [°C] .........................................33

2.7.7. Current temperature [°C] ........................................................33

2.7.8. Detection counter [cycles] ........................................................33

2.7.9. Minutes above maximum temperature [min] ...........................................33

2.7.10. Minutes below minimum temperature [min] ...........................................33

2.7.11. Download counter ............................................................33

3. Wiring diagrams ..............................................34

4. Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

5. Operation ...................................................35

5.1. User interface of PD30CTBxxxBPxxIO ....................................... 35

6. IODD ﬁle and factory setting .....................................36

6.1. IODD ﬁle of an IO-Link device ............................................. 36

6.2. Factory settings ........................................................ 36

7. Appendix ....................................................36

7.1. Acronyms ............................................................ 36

7.2. IO-Link Device Parameters for PD30CTB IO-Link ................................ 37

7.2.1. Device Identiﬁcation ............................................................ 37

7.2.2. Observation .................................................................37

7.2.3. SSC parameters ..............................................................38

7.2.4. Output Parameters .............................................................39

7.2.5. Sensor speciﬁc adjustable parameters ...............................................40

7.2.6. Application Function ...........................................................41

7.2.6.1. Speed and Length ..........................................................41

7.2.6.2. Pattern Recognition .........................................................41

7.2.6.3. Divider ..................................................................42

7.2.6.4. Object and Gap Monitoring ...................................................42

7.2.7. Diagnostic parameters ..........................................................43

Dimensions ....................................................291

Detection diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .291

Sensing Condition ...............................................292

Installation Hints ................................................293

5

EN

1. Introduction

This manual is a reference guide for Carlo Gavazzi IO-Link photoelectric sensors PD30CTBxxxBPxxIO. It

describes how to install, setup and use the product for its intended use.

1.2. Validity of documentation

This manual is valid only for PD30CTBxxxBPxxIO photoelectric sensors with IO-Link and until new documentation

is published.

1.3. Who should use this documentation

This instruction manual describes the function, operation and installation of the product for its intended use.

This manual contains important information regarding installation and must be read and completely understood

by specialized personnel dealing with these photoelectric sensors.

We highly recommend that you read the manual carefully before installing the sensor. Save the manual for future

use. The Installation manual is intended for qualified technical personnel.

1.4. Use of the product

These photoelectric diffuse reflective sensors are designed with Background Suppression, meaning it is

detecting the object via triangulation. The reciver is a detector array that performs precise detection independent

of the colour of the object and allows elimination of a background.

The received signal level can be read via the Process data in IO-Link mode.

The PD30CTBxxxBPxxIO sensors can operate with or without IO-Link communication. By means of an IO-Link

master it is possible to operate and configure these devices.

1.6. Other documents

It is possible to find the datasheet, the IODD file and the IO-Link parameter manual on the Internet at

http://gavazziautomation.com

1.5. Safety precautions

This sensor must not be used in applications where personal safety depends on the function of the sensor (The

sensor is not designed according to the EU Machinery Directive).

Installation and use must be carried out by trained technical personnel with basic electrical installation knowledge.

The installer is responsible for correct installation according to local safety regulations and must ensure that

a defective sensor will not result in any hazard to people or equipment. If the sensor is defective, it must be

replaced and secured against unauthorised use.

1.1. Description

Carlo Gavazzi photoelectric sensors are devices designed and manufactured in accordance with IEC international

standards and are subject to the Low Voltage (2014/35/EU) and Electromagnetic Compatibility (2014/30/

EU) EC directives.

All rights to this document are reserved by Carlo Gavazzi Industri, copies may be made for internal use only.

Please do not hesitate to make any suggestions for improving this document.

6

EN

1.7. Acronyms

I/O Input/Output

PD Process Data

PLC Programmable Logic Controller

SIO Standard Input Output

SP Setpoints

IODD I/O Device Description

IEC International Electrotechnical Commission

NO Normally Open contact

NC Normally Closed contact

NPN Pull load to ground

PNP Pull load to V+

Push-Pull Pull load to ground or V+

QoR Quality of Run

QoT Quality of Teach

UART Universal Asynchronous Receiver-Transmitter

SO Switching Output

SSC Switching Signal Channel

DA Dust alarm

AFO Application function output

TA Temperatur alarm

BGS Background Suppression

FGS Foreground Suppression

7

EN

2. Product

2.1. Main features

IO-Link Carlo Gavazzi 4-wire DC photoelectric Background Suppression sensors, built to the highest quality

standards, are available in Plastic (PBT) IP67 approved housing material.

They can operate in standard I/O mode (SIO), which is the default operation mode. When connected to

an SCTL55 or an IO-Link master, they automatically switch to IO-Link mode and can be operated and easily

configured remotely.

Thanks to their IO-Link interface, these devices are much more intelligent and feature many additional configuration

options, such as the settable sensing distance and hysteresis, also timer functions of the output. Advanced

functionalities such as the Logic function block and the possibility to convert one output into an external input

makes the sensor highly flexible.

Application functions such as; Pattern recognition, Speed and Length monitoring, Divider function and Object

and Gap detection are de-central functions dedicated to solve specific sensing tasks.

2.2. Identification number

Additional characters can be used for customized versions.

Code Option Description

P-Photoelectric Sensor

D-Rectangular housing

30 -Housing size

C-Plastic housing - PBT

T-Top trimmer

B-Background Suppression

IInfrared light

RRed light

SPointSpot light source

20 200 mm sensing distance

25 250 mm sensing distance

35 350 mm sensing distance

B-Selectable functions: NPN, PNP, Push-Pull, External Input (only pin 2), External teach

input (only pin 2)

P-Selectable: NO or NC

A2 2 metre PVC cable

M5 M8, 4-pole connector

IO -IO-Link version

8

EN

2.3. Operating modes

IO-Link photoelectric sensors are provided with two switching outputs (SO) and can operate in two different

modes: SIO mode (standard I/O mode) or IO-Link mode (pin 4).

2.3.1. SIO mode

When the sensor operates in SIO mode (default), a SCTL55 or an O-Link master is not required. The device

works as a standard photoelectric sensor, and it can be operated via a fieldbus device or a controller (e.g. a

PLC) when connected to its PNP, NPN or push-pull digital inputs (standard I/O port). One of the greatest benefits

of these photoelectric sensors is the possibility to configure them via a SCTL55 or an O-Link master and then,

once disconnected from the master, they will keep the last parameter and configuration settings. In this way

it is possible, for example, to configure the outputs of the sensor individually as a PNP, NPN or push-pull, or

to add timer functions such as T-on and T-off delays or logic functions and thereby satisfy several application

requirements with the same sensor.

2.3.2. IO-Link mode

IO-Link is a standardized IO technology that is recognized worldwide as an international standard (IEC 61131-9).

It is today considered to be the “USB interface” for sensors and actuators in the industrial automation environment.

When the sensor is connected to one IO-Link port, the SCTL55 or IO-Link master sends a wakeup request (wake up

pulse) to the sensor, which automatically switches to IO-Link mode: point-to-point bidirectional communication then

starts automatically between the master and the sensor.

IO-Link communication requires only standard 3-wire unshielded cable with a maximum length of 20 m.

1

2 4

3

L+

C/Q

L-

IO-Link

SIO

IO-Link communication takes place with a 24 V pulse modulation, standard UART protocol via the switching and

communication cable (combined switching status and data channel C/Q) PIN 4 or black wire.

For instance, an M8 4-pin male connector has:

• Positive power supply: pin 1, brown

• Negative power supply: pin 3, blue

• Digital output 1: pin 4, black

• Digital output 2: pin 2, white

The transmission rate of PD30CTBxxxBPxxIO sensors is 38.4 kBaud (COM2).

Once connected to the IO-Link port, the master has remote access to all the parameters of the sensor and to

advanced functionalities, allowing the settings and configuration to be changed during operation, and enabling

diagnostic functions, such as temperature warnings, temperature alarms and process data.

Thanks to IO-Link it is possible to see the manufacturer information and part number (Service Data) of the

device connected, starting from V1.1. Thanks to the data storage feature it is possible to replace the device and

automatically have all the information stored in the old device transferred into the replacement unit.

9

EN

Access to internal parameters allows the user to see how the sensor is performing, for example by reading the

internal temperature.

Event Data allows the user to get diagnostic information such as an error, an alarm, a warning or a communication

problem.

There are two different communication types between the sensor and the master and they are independent of

each other:

• Cyclical for process data and value status – this data is exchanged cyclically.

• Acyclical for parameter configuration, identification data, diagnostic information and events

(e.g. error messages or warnings) – this data can be exchanged on request.

2.3.3. Process data

By default the process data shows the following parameters as active: 16 bit Analogue value, Switching

Output1 (SO1) and Switching Output 2 (SO2).

The following parameters are set as Inactive: SSC1, SSC2, TA, SC, DA1, DA2, AFO1.

However by changing the Process Data Configuration parameter, the user can decide to also enable the status

of the inactive parameters. This way several states can be observed in the sensor at the same time.

Process data can be configured. See 2.5.3. Process data configuration.

Byte 0 31 30 29 28 27 26 25 24

MSB

Byte 1 23 22 21 20 19 18 17 16

LSB

Byte 2 15 14 13 12 11 10 9 8

SC TA DA2 DA1 SSC2 SSC1

Byte 3 76543210

AFO1 SO2 SO1

4 Bytes

Analogue value 16 … 31 (16 BIT)

10

EN

2.4. Output Parameters

Seven sensing functions and 4 application functions can be selected. These values can be independently adjusted

and used as source for the Switching Output 1 or 2; in addition to those, an external input can be selected for

SO2. After selecting one of these sources, it is possible to configure the output of the sensor with a SCTL55 or

an IO-Link master, following the seven steps shown in the Switching Output setup below.

Once the sensor has been disconnected from the master, it will switch to the SIO mode and keep the last

configuration setting.

S.P.1 (trimmer/IO-Link)

S.P.2

Hysteresis (man./auto)

Logic

Single point

Two point

Windows

FGS

S.P.1

S.P.2

Hysteresis

Logic

Single point

Two point

Windows

FGS

3. Temperature

4. Dust 1

5. Dust 2

6. EXT-Input

Selector

ALogic

A - B Time

delay Output

inverter Sensor

output

One of

1 to 7 AND, OR,

XOR, S-R ON, OFF

One-shot N.O., N.C. NPN, PNP,

Push-Pull

Selector

BLogic

A - B Time

delay Output

inverter Sensor

output

One of

1 to 7 AND, OR,

XOR, S-R ON, OFF

One-shot N.O., N.C. NPN, PNP,

Push-Pull

EXT-Input

A

B

A

B

SO1

SO2

EXT-

Input

1. SSC1

2. SSC2

Sensor front

SSC1

SSC2

Pattern

Recognition Object & Gap

Monitoring

Speed &

Length Divider

function

or or

or

7. Aplication functions

1 2 3 4 5

7

6

11

EN

2.4.1.2. Switchpoint mode:

Each SSC channel can be set operate in 4 modes or be disabled. The Switchpoint mode setting can be

used to create more advanced output behaviour. The following switchpoint modes can be selected for the

switching behaviour of SSC1 and SSC2

Disabled

SSC1 or SSC2 can be disabled individually.

Single point mode

The switching information changes, when the distance passes the threshold defined in setpoint SP1, with

rising or falling distances, taking into consideration the hysteresis settings stored in the sensor.

Sensor

Sensing distance

ON OFF

SP1

Hysteresis

Example of presence detection - with non-inverted logic

2.4.1. Sensor front

The Background Suppression sensor emits light towards a target and measure the position of the light reflected

from the target. If the measured position value is equal to or less than a predefined position for the target, the

sensor changes the output state. The measured sensing distance is almost independent of the target colour.

2.4.1.1. SSC (Switching Signal Channel)

For presence (or absence) detection of an object in front of the face of the sensor, the following settings are

available: SSC1 or SSC2. Setpoints can be set from 20 ... 225 mm for PD30CTB.20..., 20 ... 275 mm for

PD30CTBS25... and 20 ... 375 mm for the PD30CTBR35... sensor *.

1

* It is not recommended to use settings higher than maximum 200, 250 and 350 mm depending on the sensor

type however under optimal conditions (ambient light environment and EMC noise etc.) the distance can be set

at higher value.

12

EN

Window mode

The switching information changes, when the distance measured passes the thresholds defined in setpoint

SP1 and setpoint SP2, with increasing or decreasing distance measured, taking into consideration the

hysteresis settings stored in the sensor.

Sensor

Sensing distance

SP2

Hyst

OFF OFF

ON

SP1

Hyst

window

Example of presence detection - with non-inverted logic

Two point mode

The switching information changes when the distance measured passes the threshold defined in setpoint

SP1. This change occurs only with decreasing distance measured. The switching information also changes

when the distance measured passes the threshold defined in setpoint SP2. This change occurs only with

increasing distance measured. Hysteresis settings stored in the sensor are not applied in this case. The

hysteresis results from the difference between SP1 and SP2.

Sensor

Sensing distance

ON OFF

SP2

Hysteresis

SP1

Example of presence detection - with non-inverted logic

Sensor

Sensing distance

SP2

Hyst

ON ON

OFF

SP1

Hyst

FGS

Background

Foreground suppression Mode

In foreground suppression mode, the sensor is set to detect a background in a predefined distance. If the

background is no longer detected in this predefined distance, e.g. because the reflected light from the

background is blocked by an object, the sensor changes the output state.

Example of presence detection - with non-inverted logic

13

EN

2

2.4.2. Input selector

This function block allows the user to select any of the signals from the “sensor front” to the Channel A or B.

Channels A and B: can select from SSC1, SSC2, Dust alarm 1, Dust alarm 2, Water drop alarm 1, Water drop

alarm 2, Temperature alarm and External input.

3

2.4.3. Logic function block

In the logic function block a logic function can be added directly to the selected signals from the input selector

without using a PLC – making decentralised decisions possible.

The logic functions available are: AND, OR, XOR, SR-FF.

2.4.1.6. External input

The output 2 (SO2) can be configured as an external input allowing external signals to be fed into the

sensor, e.g. from a second sensor or from a PLC or directly from machine output.

2.4.1.4. Dust alarm 1 and Dust alarm 2

Minimum Excess Gain is used for dust alarm levels and is set as a common value for both SSC1

and SSC2. The dust alarm will be active after a preset time, if the measured Excess Gain value is

below the Minimum Excess gain.

See 2.5.10 Excess Gain.

2.4.1.5. Temperature alarm (TA)

The sensor monitors constantly the internal temperature. Using the temperature alarm setting it is possible to

get an alarm from the sensor if temperature thresholds are exceeded. See §2.5.5.

Two independent temperature alarm settings can be set. One for the maximum temperature alarm and one

for the minimum temperature alarm.

It is possible to read the temperature of the sensor via the acyclic IO-Link parameter data.

NOTE!

The temperature measured by the sensor will always be higher than the ambient temperature, due to internal

heating.

The difference between ambient temperature and internal temperature is influenced by how the sensor is

installed in the application.

2.4.1.3. Hysteresis Settings

The hysteresis can be set automatically or manually for SSC1 and manually only for SSC2. The hysteresis is

set in mm for SP1 and SP2.

Note: When trimmer is selected, the default hysteresis is Automatic.

Automatic hysteresis:

Automatic hysteresis will guarantee stable operation for most applications.

Hysteresis is calculated with reference to SP1/SP2 and the actual values can be read via parameter “SSC1

Auto hysteresis”, typically 14 mm for PD30CTB.20.., 17 mm for PD30CTBS25... and 24 mm for

PD30CTBR35... for SP1 and SP2.

Manual hysteresis:

When manual hysteresis is selected the hysteresis can be changed between 2 ... 225 mm for PD30CTB.20...,

2 ... 275 mm for PD30CTBS25 and 2 ... 375 mm for PD30CTBR...

For application that require a hysteresis other than the automatic, the hysteresis can be configured manually.

This feature makes the sensor more versatile.

Note: Special attention to the application must be considered when choosing a hysteresis lower than the

automatic hysteresis.

14

EN

OR function

Symbol Truth table

A B Q

0 0 0

0 1 1

1 0 1

1 1 1

Boolean Expression Q = A + B Read as A OR B gives Q

2-input OR Gate

XOR function

Symbol Truth table

A B Q

0 0 0

0 1 1

1 0 1

1 1 0

Boolean Expression Q = A + B A OR B but NOT BOTH gives Q

2-input XOR Gate

+

AND function

Symbol Truth table

A B Q

0 0 0

0 1 0

1 0 0

1 1 1

Boolean Expression Q = A.B Read as A AND B gives Q

2-input AND Gate

15

EN

“Gated SR-FF” function

The function is designed to: e.g. start or stop signal for a buffer conveyor dependent on the ﬁll status of the

adjacent feeder or receiver conveyor using only two interconnected sensors.

Symbol Truth table

A B Q

0 0 0

0 1 X

1 0 X

1 1 1

X – no changes to the output.

2.4.4. Timer (Can be set individually for Out1 and Out2)

The Timer allows the user to introduce different timer functions by editing the 3 timer parameters:

• Timer mode

• Timer scale

• Timer value

4

2.4.4.1. Timer mode

This selects which type of timer function is introduced on the Switching Output. Any one of the following is

possible:

2.4.4.1.1. Disabled

This option disables the timer function no matter how the timer scale and timer delay is set up.

2.4.4.1.2. Turn On delay (T-on)

The activation of the switching output is generated after the actual sensor actuation as shown in the figure

below.

Presence of

target

N.O. Ton Ton Ton

Presence of target

Example with normally open output

16

EN

2.4.4.1.5. One shot leading edge

Each time a target is detected in front of the sensor the switching output generates a pulse of constant

length on the leading edge of the detection. This function is not retriggerable. See figure below.

N.O. ∆t ∆t ∆t∆t

Presence of target

Example with normally open output

2.4.4.1.3. Turn Off delay (T-off)

The deactivation of the switching output is delayed until after to the time of removal of the target in the front

of the sensor, as like shown in the figure below.

Presence of

target

N.O. Toff Toff Toff Toff

Presence of target

2.4.4.1.4. Turn ON and Turn Off delay (T-on and T-off)

When selected, both the Ton and the Toff delays are applied to the generation of the switching output.

N.O. Ton Ton Ton

Toff Toff

Presence of target

Example with normally open output

17

EN

2.4.4.1.6. One shot trailing edge

Similar in function to the one shot leading edge mode, but in this mode the switching output is changed on

the trailing edge of the activation as shown in the figure below. This function is not retriggerable.

N.O. ∆t ∆t ∆t∆t

Presence of target

Example with normally open output

2.4.4.2. Timer scale

The parameter defines if the delay specified in the Timer delay should be in milliseconds, seconds or minutes

2.4.4.3. Timer Value

The parameter defines the actual duration of the delay. The delay can be set to any integer value between

1 and 32 767.

2.4.5. Output Inverter

This function allows the user to invert the operation of the switching output between Normally Open and

Normally Closed.

5

RECOMMENDED FUNCTION

The recommended function is found in the parameters under 64 (0x40) sub index 8 (0x08) for SO1 and 65

(0x41) sub index 8 (0x08) for SO2. It has no negative influence on the Logic functions or the timer functions of

the sensor as it is added after those functions.

CAUTION!

The Switching logic function found under 61 (0x3D) sub index 1 (0x01) for SSC1 and 63 (0x3F) sub index

1 (0x01) for SSC2 are not recommended for use as they will have a negative influence on the logic or timer

functions. Using this function will turn an ON delay into an Off delay if it is added for the SSC1 and SSC2. It

is only for the SO1 and SO2.

2.4.6. Output stage mode

In this function block the user can select if the switching outputs should operate as:

SO1: Disabled, NPN, PNP or Push-Pull configuration.

SO2: Disabled, NPN, PNP, Push-Pull , External input (Active high/Pull-down), External input

(Active low/pull up) or External Teach input.

6

18

EN

2.4.7. Application functions

4 unique application functions can be selected via IO-Link only.

• Speed and Length.

• Pattern Recognition.

• Divider.

• Object and Gap Monitoring.

All application functions are disabled as factory setting.

7

2.4.7.1. Speed and Length

This function is designed to monitor the length of an object as well as the speed of a conveyor belt by

means of only two interconnected sensors. The actual value if the length in [mm] and the speed in [mm/s]

are directly available on the IO-Link master.

Either the length or the speed can be set as process data.

2.4.7.1.1. Conditions

Two sensors are needed for this function: a Trigger sensor and a Main sensor.

2.4.7.1.2. Speed and Length – Setup procedure

Sensor preparation

1) Mount two sensors at the conveyor with an individual distance of e.g. 100 mm

2) Connect the two sensors to an SCTL55 or IO-Link master

3) Upload the IODD files in the SCTL55 or IO-Link Master

4) Switch on the power to the sensors

5) Restore the sensors to factory settings using the SCTL55 or IO-Link master.

6) Align the two sensors so the light beams are parallel to each other and aimed at the target.

7) Adjust the sensitivity on the sensors to get a reliable detection on the object.

(The yellow LED is ON, and the green LED is ON indicating stable ON and IO-Link Mode)

IO-Link parameter settings (see Data Range options in § 7.2.6.1.)

8) Trigger sensor: (The object passes the Trigger Sensor first)

a) Select “Speed and Length” in the SCTL55 or IO-Link master; Menu “Parameter” -> “Application

Functions”

Alignment of Trigger and Main Sensor

19

EN

b) Select “Sensor role” -> “Trigger Sensor”

c) IO-Link Parameter Set-up is finished for the Trigger Sensor

9) Main sensor: (calculates Speed and Length and makes data available via IO-Link)

a) Reset the sensor using “Restore factory Settings”

(if already performed in point 5 then this can be skipped).

b) Select “Speed and Length” in the SCTL55 or IO-Link master; Menu “Parameter” -> “Application

Functions”

c) Select “Sensor role” -> “Main Sensor”.

d) Enter the distance in between the two sensors in [mm] in the menu “Speed and Length Measurement

Main Sensor” -> “Distance between sensors”

e) Select “Object Length” or “Object Speed” if required in “Process Data” in the “Observation menu”

under “Process data configuration” -> “Analogue value”

i. Object Length will be shown in [mm]

ii. Object Speed will be shown in [mm/s]

10) Connect sensor output Pin 2 of the Trigger Sensor to Input Pin 2 of the Main Sensor

11) The Speed and length function is now ready for use.

NB! During the measurement variations in the conveyor speed may impact the result.

2.4.7.2. Pattern Recognition

The pattern recognition function is used to verify if a manufactured part has all the e.g. holes or taps as

expected and that the parts are made according to the specification.

A pattern of a part can be recorded into the sensor and the following parts then compared to the pre-

recorded pattern.

If pattern match, the sensor will respond with a positive signal or command either as standalone operation

or via an IO-Link master

The pattern can max. contain 20 edges eg. 10 holes or 10 taps.

If multiple pattern are to be detected then several Main sensors can be connected to a single Trigger sensor.

2.4.7.2.1. Conditions

Two sensors are needed for this function a Trigger Sensor and a Main Sensor, however several Main

sensors can be connected to the Trigger Sensor if more than one pattern must be examined simultaneously.

2.4.7.2.2. Pattern recognition – Setup procedure

Sensor preparation

1) Mount two sensors at the conveyor in line so the object will reach the two sensors at the same time.

2) Connect the two sensors to an SCTL55 or IO-Link master

3) Upload the IODD files in the SCTL55 or IO-Link Master

Alignment of Trigger and Main Sensor

20

EN

4) Switch on the power to the sensors

5) Restore the sensors to factory settings using the SCTL55 or IO-Link master.

6) Align the two sensors so the light beams will be detecting the edge of the target at the same time.

7) The trigger sensor must be mounted in a position where it will continuously detect the object without

any holes or taps.

8) The Main sensor must be mounted so it detects the taps or holes that contain the pattern to be

examined

9) Adjust the sensitivity on the sensors to get a reliable detection on the target.

(The yellow LED are ON, and the green LED are ON indicating Stable ON and IO-Link Mode)

IO-Link parameter settings (see Data Range options in § 7.2.6.2.)

10) Trigger sensor:

a) Select “Pattern Recognition” in the SCTL55 or IO-Link master; Menu “Parameter” -> “Application

Functions”

b) Select “Sensor role” -> “Trigger Sensor”

c) IO-Link Parameter Set-up is finished for the Trigger Sensor

11) Main sensor:

a) Select “Pattern Recognition” in the SCTL55 or IO-Link master; Menu “Parameter” -> “Application

Functions”

b) Select “Sensor role” -> “Main Sensor”.

c) Enter the Timeout value used for maximum evaluation time between 1 … 60 sec, in the menu

“Pattern Recognition Setup” -> “Timeout” (default value is 60 sec.)

d) Enter the Tolerance of the Pattern in ‰ (Parts per thousand), between 1 and 200 ‰ in the menu

“Pattern Recognition Setup” -> “Tolerance”, default value is 50 ‰

12) Connect sensor output Pin 2 of the Trigger Sensor to Input Pin 2 of the Main Sensor(s)

Teach the Pattern

13) Activate the “Teach Pattern” command to start learning the pattern

14) Move the target at a steady speed passing fully by the two sensors

NB! During the measurement variations in the conveyor speed may impact the result.

15) The sensor responds with:

a) “Saved” in “Pattern Recognition Result” -> “Reference Pattern”

b) “E.g. 12” in “Pattern Recognition Result” -> “Reference Pattern No Of Edges” (counts both the

leading and trailing edges of the measurement targets).

c) Each edge is saved in ms from the leading edge of the complete measurement target and can be

found in the Observation menu. When compared to the reference pattern the edges are normalized

as a percentage value of the complete measurement target.

This ensures that the pattern can be recognized at various constant speeds.

16) The Pattern can be saved as a project in the SCTL55 or IO-Link master and at a later point send back

to the sensor in order to use this specific saved pattern as a reference pattern.

17) The Pattern Recognition function is now ready for use.

18) Move the target again at a steady speed passing fully by the two sensors

19) The Sensor responds with the text

a) “E.g. 12” in “Pattern Recognition Result” -> “Number of Edges Last Pattern”

20) “Patterns Match” in “Pattern Recognition Result” -> “Pattern Recognition Status”

Standalone operation in SIO Mode

21) Disconnect the sensor from the SCTL55 or IO-Link master and connect the Pin 4 to your e.g. decentral

Tower light or good/bad conveyor belt

22) Once a valid pattern is detected the Pin 4 output responds with a 1 second pulse.

Multiple patterns

Multiple patterns can be detected simultaneously on the same target using only one Trigger sensor and

multiple Main sensors, each Main sensor responds to a specific Pattern.

La page charge ...

CARLO GAVAZZI PD30CTBI20BPM5IO Le manuel du propriétaire

Ce manuel convient également à

CARLO GAVAZZI PD30CTBI20BPM5IO Le manuel du propriétaire