LG OLED65G3PUA Le manuel du propriétaire

Marque: LG

Modèle: OLED65G3PUA

Catégorie: Téléviseurs LCD

Taper: Le manuel du propriétaire

Ce manuel convient également à

ENGLISH_index

Safety and Reference

OWNER’S MANUAL

Please read this manual carefully

before operating your set and retain

it for future reference.

Printed in Korea

www.lg.com

The model and serial number of the product are

located on the back and on one side of the product.

Record them below in case you ever need service.

Model

Serial No.

OLED55G3PUA

OLED65G3PUA

OLED77G3PUA

OLED83G3PUA

OLED77Z3PUA

*MFL719463332301REV00*

Supplier`s Declaration of

Conformity

Trade Name LG

Responsible

Party

LG Electronics USA,

Inc.

Address 111 Sylvan Avenue,

North Building,

Englewood Cliffs,

NJ07632

E-mail lg.environmental@

lge.com

LG Customer Information Center

For inquires or comments, visit www.

lg.com or call;

1-888-542-2623 CANADA

1-800-243-0000 USA, Consumer

User

1-888-865-3026 USA, Commercial

User

www.lg.com

Important Safety Instruction

•Read these instructions.

•Keep these instructions.

•Heed all warnings.

•Follow all instructions.

•Do not use this apparatus near water.

•Clean only with dry cloth.

•Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

•Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

•Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

•Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

•Only use attachments/accessories specified by the manufacturer.

•Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid injury from tip-over.

•Unplug this apparatus during lightning storms or when unused for long periods of time.

•Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate

normally, or has been dropped.

Before reading this manual

•Read this manual thoroughly before operating your TV, and keep it for future reference.

•On the website you can download the manual including installation, using, troubleshooting, specifications, license etc and view its contents on your PC or

mobile device.

•User Guide: For more information about this TV, read the USER GUIDE embedded in the product. (Depending upon model)

-To open the USER GUIDE → [ ] → [Support] → [User Guide]

Optional Extras

•Optional extras can be changed or modified for quality improvement without any notification. Contact your dealer for buying these items. These devices

work only with certain models. The model name or design may be changed due to the manufacturer’s circumstances or policies.

•A cable to connect antennas and external devices must be purchased separately.

Note

•Product specifications or contents of this manual may be changed without prior notice due to upgrade of product functions.

•The items supplied with your product may vary depending upon the model.

•Image shown may differ from your TV.

By using this product, you agree that all disputes between you and LG arising out of or relating in any way to this product (including but not limited to warranty

disputes) shall be resolved exclusively through binding arbitration on an individual basis. The terms of the arbitration agreement (including details on the

procedure for resolving disputes) is available at www.lg.com/us/arbitration (USA) or www.lg.com/ca_en/arbitration (Canada).

Warning! Safety instructions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE

PERSONNEL.

The symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to persons.

The symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature

accompanying the device.

WARNING: TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

•TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITEMS WITH

OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.

•Do not place the TV and/or remote control in the following

environments:

-Keep the product away from direct sunlight.

-An area with high humidity such as a bathroom.

-Near any heat source such as stoves and other devices that produce

heat.

-Near kitchen counters or humidifiers where they can easily be exposed

to steam or oil.

-An area exposed to rain or wind.

-Do not expose to dripping or splashing and do not place objects filled

with liquids, such as vases, cups, etc. on or over the apparatus (e.g., on

shelves above the unit).

-Near flammable objects such as gasoline or candles, or expose the TV

to direct air conditioning.

-Do not install in excessively dusty places.

Otherwise, this may result in fire, electric shock, combustion/explosion,

malfunction or product deformation.

•Ventilation

-Install your TV where there is proper ventilation. Do not install in a

confined space such as a bookcase.

-Do not install the product on a carpet or cushion.

-Do not block or cover the product with cloth or other materials while

unit is plugged in.

•Take care not to touch the ventilation openings. When watching the TV

for a long period, the ventilation openings may become hot.

•Protect the power cord from physical or mechanical abuse, such as being

twisted, kinked, pinched, closed in a door, or walked upon. Pay particular

attention to plugs, wall outlets, and the point where the cord exits the

device.

•Do not move the TV whilst the Power cord is plugged in.

•Do not use a damaged or loosely fitting power cord.

•Be sure to grasp the plug when unplugging the power cord. Do not pull

on the power cord to unplug the TV.

•Do not connect too many devices to the same AC power outlet as this

could result in fire or electric shock.

•Disconnecting the Device from the Main Power

-The power plug is the disconnecting device. In case of an emergency,

the power plug must remain readily accessible.

•Do not let your children climb or cling onto the TV. Otherwise, the TV

may fall over, which may cause serious injury.

•Outdoor Antenna Grounding (Can differ by country):

-If an outdoor antenna is installed, follow the precautions below.

An outdoor antenna system should not be located in the vicinity of

overhead power lines or other electric light or power circuits, or where

it can come in contact with such power lines or circuits as death or

serious injury can occur.

Be sure the antenna system is grounded to provide some protection

against voltage surges and built-up static charges.

Section 810 of the National Electrical Code (NEC) in the U.S.A. provides

information with respect to proper grounding of the mast and

supporting structure, grounding of the lead-in wire to an antenna

discharge unit, size of grounding conductors, location of antenna

discharge unit, connection to grounding electrodes and requirements

for the grounding electrode.

Antenna grounding according to the National Electrical Code, ANSI/

NFPA 70

•Never touch this apparatus or antenna during a lightning storm. You may

be electrocuted.

•Make sure the power cord is connected securely to the TV and wall socket

if not secured damage to the Plug and socket may occur and in extreme

cases a fire may break out.

•Do not insert metallic or inflammable objects into the product. If a

foreign object is dropped into the product, unplug the power cord and

contact the customer service.

•Do not touch the end of the power cord while it is plugged in. You may

be electrocuted.

•If any of the following occur, unplug the product immediately

and contact your local customer service.

-The product has been damaged.

-If water or another substance enters the product (like an AC adapter,

power cord, or TV).

-If you smell smoke or other odors coming from the TV

-When lightning storms or when unused for long periods of time.

Even the TV is turned off by remote control or button, AC power source is

connected to the unit if not unplugged in.

•Do not use high voltage electrical equipment near the TV (e.g., a bug

zapper). This may result in product malfunction.

•Do not attempt to modify this product in any way without written

authorization from LG Electronics. Accidental fire or electric shock

can occur. Contact your local customer service for service or repair.

Unauthorized modification could void the user’s authority to operate

this product.

•Use only an authorized attachments / accessories approved by LG

Electronics. Otherwise, this may result in fire, electric shock, malfunction,

or product damage.

•Never disassemble the AC adapter or power cord. This may result in fire

or electric shock.

•Handle the adapter carefully to avoid dropping or striking it. An impact

could damage the adapter.

•To reduce the risk of fire or electrical shock, do not touch the TV with wet

hands. If the power cord prongs are wet or covered with dust, dry the

power plug completely or wipe dust off.

•Batteries

-Store the accessories (battery, etc.) in a safe location out of the reach

of children.

-Do not short circuit, disassemble, or allow the batteries to overheat.

Do not dispose of batteries in a fire. Batteries should not be exposed

to excessive heat.

-Caution: Risk of fire or explosion if the battery is replaced by an

incorrect type.

•Moving

-When moving, make sure the product is turned off, unplugged, and

all cables have been removed. It may take 2 or more people to carry

larger TVs. Do not press or put stress on the front panel of the TV.

Otherwise, this may result in product damage, fire hazard or injury.

•Keep the packing anti-moisture material or vinyl packing out of the

reach of children.

•Do not allow an impact shock, any objects to fall into the product, and do

not drop anything onto the screen.

•Do not press strongly upon the panel with a hand or a sharp object such

as a nail, pencil, or pen, or make a scratch on it. It may causedamage

to screen.

•Cleaning

-When cleaning, unplug the power cord and wipe gently with a soft/

dry cloth. Do not spray water or other liquids directly on the TV. Do

not clean your TV with chemicals including glass cleaner, any type of

air freshener, insecticide, lubricants, wax (car, industrial), abrasive,

thinner, benzene, alcohol etc., which can damage the product and/

or its panel. Otherwise, this may result in electric shock or product

damage.

Installation

Lifting and moving the TV

When moving or lifting the TV, read the following to prevent the TV from

being scratched or damaged and for safe transportation regardless of its type

and size.

•It is recommended to move the TV in the box or packing material that

the TV originally came in.

•Before moving or lifting the TV, disconnect the power cord and all cables.

•When holding the TV, the screen should face away from you to avoid

damage.

•Hold the side and bottom of the TV frame firmly. Make sure not to hold

the transparent part, speaker, or speaker grille area.

•Use at least two people to move a large TV.

•When transporting the TV, do not expose the TV to jolts or excessive

vibration.

•When transporting the TV, keep the TV upright; never turn the TV on its

side or tilt towards the left or right.

•When handling the TV, be careful not to damage the protruding buttons.

•Avoid touching the screen at all times, as this may result in damage to

the screen.

•Do not place the product on the floor with its front facing down without

padding. Failure to do so may result in damage to the screen.

•When attaching the stand to the TV set, place the screen facing down on

a cushioned table or flat surface to protect the screen from scratches.

Mounting on the Table

1 Lift and tilt the TV into its upright position on a table.

• Leave a minimum of 10 cm (4 inches) space from the wall for proper

ventilation, (Depending upon model).

2 Connect the power cord to a wall outlet.

•Do not apply foreign substances (oils, lubricants, etc.) to the screw parts

when assembling the product. (Doing so may damage the product.)

•Do not use any unapproved items to ensure the safety and lifespan of

the product.

•Any damages or injuries by using unapproved items are not covered by

the warranty.

•If you install the TV on a stand, you need to take actions to prevent the

product from overturning. Otherwise, the product may fall over, which

may cause injury.

•When assembling the stand, ensure that all of the provided screws are

attached. If the screws are not fully tightened, the product may tilt or

tip over, resulting in damage. Tightening the screws with excessive force

may cause them to come off due to abrasion of the screw joint.

•When installing on a cabinet or a shelf using a stand, make sure its width

is greater than that of the TV, (Depending upon model).

•If the TV is placed on the stand, its screen may be tilted back slightly. If

the stand is not level because an object is placed under the stand or it

is not on a flat surface, the product may fall and cause injury or product

damage, (Depending upon model).

Securing TV to the Wall

1 Insert and tighten the eye-bolts or TV brackets and bolts on the back of

the TV.

• If there are bolts inserted at the eye-bolts position, remove the bolts

first.

2 Mount the wall brackets with the bolts to the wall. Match the location of

the wall bracket and the eye-bolts on the rear of the TV.

3 Connect the eye-bolts and wall brackets tightly with a sturdy rope or

cable. Make sure to keep the rope parallel to the flat surface.

•Use a platform or cabinet that is strong and large enough to support the

TV securely.

•Brackets, bolts, and ropes are optional. You can obtain additional

accessories from your local dealer.

Stand (Optional Extras)

(Depending upon model)

Stand Model

SR-G3WU55 OLED55G3*

SR-G3WU65 OLED65G3*

SR-G3WU8377 OLED77/83G3*

Mounting to the Wall

An optional wall mount can be used with your LG Television. Consult with

your local dealer for a wall mount that supports the VESA standard used by

your TV model. Carefully attach the wall mount bracket at the rear of the TV.

Install the wall mount bracket on a solid wall perpendicular to the floor. If

you are attaching the TV to other building materials, please contact qualified

personnel to install the wall mount. Detailed instructions will be included

with the wall mount. We recommend that you use an LG brand wall mount.

The LG wall mount is easy to adjust or to connect the cables. When you do

not use LG’s wall mount bracket, use a wall mount bracket where the device

is adequately secured to the wall with enough space to allow connectivity to

external devices. If you are using a non-adjustable mount, attach the mount

to the wall. Attach the cables to the TV first, then attach the TV to the mount.

•Remove the stand before installing the TV on a wall mount by

performing the stand attachment in reverse.

•For more information of screws and wall mount bracket, refer to the

Separate purchase.

•If you intend to mount the product to a wall, attach VESA standard

mounting interface (optional parts) to the back of the product. When you

install the set to use the wall mounting bracket (optional parts), fix it

carefully so as not to drop.

•When mounting a TV on the wall, make sure not to install the TV by

hanging the power and signal cables on the back of the TV.

•Do not install this product on a wall if it could be exposed to oil or oil

mist. This may damage the product and cause it to fall.

•When installing the Full Contact Wall Mount, the TV may not be

contacted firmly against the wall due to some wall conditions.

Precautions for Safety

(Except for OLW480B, LSW440B)

•Professional installers should read this manual carefully to ensure proper

installation.

•Professional installers should forward this manual to customers after

installation and encourage them to read and store it in a convenient

place for future reference.

After reading the installation manual, keep it in a convenient place for

future reference.

•Ask a professional installer appointed by the store for installation of the

product.

Installation by someone other than a professional installer is extremely

dangerous and may result in personal injury.

•Do not install the product in an unstable site that cannot withstand its

weight.

If the installation site lacks sufficient rigidity, the product may fall and

cause personal injury.

•Contact a professional installer appointed by the store prior to moving or

replacing the product after installation.

Installation is a technical task and safety issues may arise if an individual

attempts to install or move the product personally.

•Do not hang on the product or subject it to severe impact after

installation.

Doing so may cause the product to fall and cause personal injury.

•When installing the product on a wall, do not hang the power line or

signal cables from the back of the TV.

This can damage the cords, resulting in a fire, electrical shock or

malfunction of the product.

•Be sure to wear work gloves when installing the product.

-Installing with unprotected hands may result in injury.

•Install the product according to the instructions in the installation

manual.

Failure to install the product according to the instructions in the

installation manual can result in serious personal injury or product

damage.

•Be sure to have at least two people when installing the product or

adjusting the product’s height.

Attempting to perform installation or adjustments personally may result

in personal injury or damage to the product.

•Make sure a wall is available prior to proceeding with installation. Make

use of the anchors and screws provided with the product.

Use of any unauthorized anchors or screws may not support the

product’s weight, which poses safety risks.

•When drilling in the wall for installation, be sure to use drill bits and

drills of the specified diameter. Follow the instructions for the hole

depth.

Drilling and installing the product in ways other than specified in the

installation manual may result in an unstable installation and potential

safety issues.

•Do not wipe the product with a wet towel or use any heating equipment

or humidifier under the place where the product is installed.

Liquid water or vapor may enter the product and excessive heat may

cause fire, electric shock, or malfunction.

•Do not install the product near a fire sprinkler or detector, a place where

vibration or shock may occur or near a high-voltage wire or power

source.

•Unplug the product’s power cord from the wall outlet before installing.

Installing the product while the power cord is plugged in may result in

electric shock or fire.

•Do not install the product with bare hands. Be sure to wear work gloves.

Attempting installation without work gloves may cause personal injury.

•Connect the product with the supplied cable. Use of an unauthorized

cable may result in damage by friction with the wall. Make sure to use

the supplied cable gender. (This may vary by model.)

Before Installation

(Except for OLW480B, LSW440B)

•Do not use the product for any purpose other than installing the TV on

a wall.

•Avoid product damage and safety accidents caused by careless installing

or use of improper or unauthorized wall mount.

•Follow the instructions in the installation manual for a convenient

installation of the wall mount.

•Immediately discontinue installation and contact the service center if

you cannot fully understand the installation process.

Use a professional installer if any installation issues remain after the

inquiry.

•Installation of this product on a concrete wall or wood stud is

recommended. Installation of this product on other surfaces (Dry wall,

plywood, bricks, etc.) is not recommended. Improper installation may

result in the product falling.

•Install the product only on a vertical wall.

Do not install on a tilted wall that exceeds building standards or on the

heavily titled wall or ceiling.

LG is not responsible for problems caused by improper installation of the

product, e.g., heavily tilted walls and ceilings.

•Check the enclosed accessories before installation. We are not

responsible for any lost or damaged accessories after the inner

packaging is opened.

•When an infant or small child swallows the enclosed accessories,

various safety accidents such as choking may occur. Keep the enclosed

accessories out of the reach of infants and children.

•When tightening screws, tighten until fully snug.

Avoid using excessive force when tightening the screws. Doing so may

damage the wall and product or reduce the rigidity or performance of

the product.

•Avoid installing a TV that exceeds the specified tensile load, and do not

allow any external force to be applied to the product.

•Avoid accidents by using work tools with care during installation.

Tools for Installation

•“+” shaped screwdriver (manual or electric) / level / drill / Ø 8 mm drill

bit for concrete or Ø 4 mm drill bit for steel

Securing TV to the Wall

(Except for OLW480B, LSW440B)

•Please use the TV close to the wall after installation.

How to fix anchors and screws

(Except for OLW480B, LSW440B)

Please make sure that:

•Check that the material and thickness of the wall and finishing material

comply with the installation manual. Before beginning the mounting

process, you must be sure the wall is able to support the weight of the

TV.

•Should use the enclosed anchors and screws on crack-free concrete walls.

•Never install the product on a plasterboard or wall made of paper or

medium-density fiberboard (MDF). When it is necessary to install the

product on such wall, anchor screws must be fastened to retaining walls

(concrete) or wood Stud inside the finishing material.

•The wall mount should be attached to a stud.This usually will not be a

problem, but depending upon individual circumstances, there may be

cases when the ability to mount into a studis not possible. In this case,

there are a variety of drywall anchors, such as toggle bolts, which may

provide a solution.If using drywall anchors, please be sure the anchors

and the wall have the ability to support the weight of your TV. Please

note that the supplied anchors may not be the correct ones for your

individual situation, so you should check with a local professional.

•Other unspecified walls must be capable of supporting pullout loads of

over 70kgf (154lbf) (686N) and shear loads of over 100kgf (220lbf)

(980N) per fastener.

•Use an Ø 8mm drill bit for concrete and a hammer (impact) drill or Ø

4mm drill bit for wood stud to drill holes.

For installation on concrete wall

Wall mounting anchor

Wall mounting screw

1 Drill holes in anchor locations with a drill bit of Ø 8 mm to a depth of

80mm (3.14inches) to 100mm (3.93inches).

2 Clean the drilled holes.

3 Insert the enclosed anchors for fixing the wall mount into the holes. (Use

a hammer when inserting anchors.)

4 Push the wall mount support closely toward the wall to match the hole

locations.

5 Tighten screws for fixing the wall mount to the holes. At this time, tighten

the screws to a torque of between 45 kgf/cm (39.06lbf/in) to 60kgf/cm

(52.07lbf/in).

For installation on wood stud

Drywall

Wood stud

76 mm (2.9 inches)

Use the Ø4mm drill bit for wood to drill holes with the depth of 76mm (2.9

Inches). (Clean the drilled hole.)

Without using the wall mounting anchor, fasten the wall mounting screw

directly to the wood stud.

After Installation

•When connecting additional cables from the sides, we recommend

holding the center of the TV horizontally or vertically and pulling the

product to make sure there is sufficient distance from the wall before

connecting.

•When connecting additional cables from the bottom, we recommend

releasing the TV from the wall mount before connecting.

(For example)

•Use cable management systems to arrange the cables at the bottom of

the TV as shown below. Cable managements are not provided with the

product, so purchase them separately.

•After installing the product, be sure to use it adhered to the wall.

-Using the product while it is not adhered to the wall may damage or

shake the product.

Antenna/Cable

Connect an antenna, cable, or cable box to watch TV while referring to the

following. The illustrations may differ from the actual items and an RF cable

is optional.

Copper wire

•Make sure not to bend the copper wire of the RF cable.

•Complete all connections between devices, and then connect the power

cord to the power outlet to prevent damage to your TV.

•Use a signal splitter to use 2 TVs or more.

•DTV Audio Supported Codec: MPEG, Dolby Digital

•This TV cannot receive Ultra HD (3840 x 2160 pixels) broadcasts directly

because the related standards have not been confirmed (Depending

upon country).

Starting TV

Turning on the TV

You can simply operate the TV functions, using the button.

Power On (Press)

Power Off1) (Press and Hold)

Menu Control (Press2))

Menu Selection (Press and Hold3))

1) All running apps will close.

2) You can access and adjust the menu by pressing the button when TV is on.

3) You can use the function when you access menu control.

Note

•When the TV is turned on for the first time after being shipped from the

factory, initialization of the TV may take approximately one minute.

•Your TV’s OSD (On Screen Display) may differ slightly from that shown

in this manual.

•The device must be easily accessed to a location outlet near the access.

Some devices are not made by turning on / off button, turning off the

device and unplugging the power cord.

Connections

You can connect various external devices to the TV. For more information on

external device’s connection, refer to the manual provided with each device.

HDMI

•When connecting the HDMI cable, the product and external devices

should be turned off and unplugged.

•Supported HDMI Audio format (Depending upon model):

True HD (48 kHz),

Dolby Digital / Dolby Digital Plus (32 kHz / 44.1 kHz / 48 kHz),

PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz / 192 kHz)

DTS (44.1kHz / 48kHz / 88.2kHz / 96kHz)

DTS-HD (44.1kHz / 48kHz / 88.2kHz / 96kHz / 176.4kHz / 192kHz)

Note

•If the device connected to Input Port also supports HDMI Deep Color,

your picture may be clearer. However, if the device doesn’t support it, it

may not work properly. In that case, change the TV’s [HDMI Deep Color]

setting to off.

• → [ ] → [General] → [External Devices] → [HDMI Settings]

→ [HDMI Deep Color]

•Use a certified cable with the HDMI logo attached. If you do not use a

certified HDMI cable, the screen may not display or a connection error

may occur.

•Recommended HDMI cable types

-Ultra High Speed HDMI®/™ cable (3m (9.84feet) or less)

USB

Some USB Hubs may not work. If a USB device connected through a USB Hub

is not detected, connect it directly to the USB port on the TV.

Note

•For an optimal connection, HDMI cables and USB devices should have

bezels less than 10mm (0.39inches) thick and 18mm (0.7inches)

width. (Depending upon model)

•Use an extension cable that supports if the USB cable or USB

flash drive does not fit into your TV’s USB port.

IR Blaster

Control the set-top box (cable/satellite/IP/OTT), Blu-ray/DVD player,

soundbar, game consoles, etc., using the IR Blaster. (Depending upon country)

•Connect the IR Blaster cable to the TV’s IR Blaster port.

•Use universal control settings to control the device.

•Secure the IR Blaster with the 3M tape provided.

•In order to control external devices through "Room to Room Share" and

"Hands-free Voice Control", an IR blaster connection is required.

External Devices

Supported external devices are: Blu-ray player, HD receivers, DVD players,

VCRs, audio systems, USB storage devices, PC, gaming devices, and other

external devices.

Note

•The external device connections shown may differ slightly from

illustrations in a manual.

•In PC mode, there may be noise associated with the resolution, vertical

pattern, contrast or brightness. If noise is present, change the PC output

to another resolution, change the refresh rate to another rate or adjust

the brightness and contrast on the [Picture] menu until the picture is

clear. Depending upon the graphics card, some resolution settings may

not allow the image to be positioned on the screen properly.

•When connecting to a wired LAN, use a CAT7 cable with high-speed

Internet transmission. (Only when port is provided.)

•The TV may be capable of operating without a set-top-box from a

multichannel video programming distributor (MVPD).

Remote RS-232C setup

To obtain the RS-232C external control setup information, please visit www.

lg.com. Download and read the manual, (Depending upon model).

•Do not drop the product or let it fall over when connecting external

devices. Otherwise, this may result in injury or damage to the product.

•When connecting external devices such as video game consoles, make

sure the connecting cables are long enough. Otherwise, the product may

fall over, which may cause injury or damage the product.

Specications

Power requirement AC 120 V~ 50/60 Hz

Product specifications may be changed without prior notice due to upgrade of product functions.

Estimated yearly energy consumption indicated on the FTC label is measured in accordance with the Test Procedures for Television Sets (USA only).

The actual energy consumption depends on the usage environment (The content watched, TV settings, etc.).

•For information of the power supply and power consumption, refer to the label attached to the product.

-The typical power consumption is measured in accordance with IEC 62087 or each country’s energy regulations.

* On some models, the label is inside the external device connection terminal cover.

* Depending upon the model or country, the typical power consumption may not be on label.

(Depending upon country)

Broadcasting Specifications

Television system ATSC, ATSC3.0 (Only USA), NTSC-M, 64 & 256 QAM

Channel coverage

(Band) VHF 2-13, UHF 14-69, DTV 2-69, CATV 1-135, CADTV 1-135

External antenna impedance 75Ω

•Certain 8K input/decoding standards may not be supported. An additional device may be necessary to support certain 8K standards. Upscaled and enhanced

8K images will vary depending upon the source content (Depending upon model).

Environment Condition

Operating Temperature 0 °C to 40 °C

(32 °F to 104 °F) Storage Temperature -20 °C to 60 °C

(-4 °F to 140 °F)

Operating Humidity Less than 80% Storage Humidity Less than 85%

Conditions for Wall Mount Installation

Tilt Angle 0° - 15°

* This specification range applies to TV wall mounts when adjusting for proper viewing angle.

Product Information

Open Source Software Notice

Information

To obtain the source code that is contained in this product, under GPL, LGPL,

MPL, and other open source licenses that have the obligation to disclose

source code, and to access all referred license terms, copyright notices and

other relevant documents please visithttps://opensource.lge.com.

LG Electronics will also provide open source code to you on CD-ROM for a

charge covering the cost of performing such distribution (such as the cost of

media, shipping, and handling) upon email request to opensource@lge.com.

This offer is valid to anyone in receipt of this information for a period of three

yearsafter our last shipment of this product.

Licenses

(Magic Remote supported models only)

Wireless module(LGSBWAX12)Specifications

Wireless LAN (IEEE 802.11a/b/g/n/ac/ax)

Frequency range Output Power (Max.)

2,400 to 2,483.5 MHz 17dBm

5,150 to 5,725MHz 15dBm

5,725 to 5,850MHz 15dBm

Bluetooth

Frequency range Output Power (Max.)

2,400 to 2,483.5MHz 9dBm

As band channels can vary per country, the user cannot change or adjust

the operating frequency. This product is configured for the regional

frequency table.

For consideration of the user, this device should be installed and operated

with a minimum distance of 20 cm (7.8 inches) between the device and

the body.

FCC ID: BEJLGSBWAX12 / IC: 2703H-LGSBWAX12

Troubleshooting

In TV / HDMI input, press the button on the remote control three times to display the model name and serial number on the screen.

Cannot control the TV with

the remote control.

•Check if anything such as tape has been placed over the receiver.

•Check if there is any obstacle between the product and the remote control.

•Replace the batteries with new fresh ones.

No image display and no

sound is produced.

•Check if the product is turned on.

•Check if the power cord is connected to a wall outlet.

•Check if there is a problem in the wall outlet by connecting other products.

The TV turns off suddenly. •Check the power control settings. The power supply may be interrupted.

•Check if the auto-off function is activated in the settings menu.

•The auto-off function may have worked. This product is equipped with an auto-off function that automatically

turns off the power if the remote control is not used for 15 minutes without an input signal.

Abnormal Display •If the product feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is

nothing wrong with product.

•This panel is an advanced product that contains millions of pixels. You may see tiny black dots and/or brightly

colored dots (white, red, blue or green) at a size of 1 ppm on the panel. This does not indicate a malfunction and

does not affect the performance and reliability of the product. This phenomenon also occurs in third-party products

and is not subject to exchange or refund.

•You may find different brightness and color of the panel depending upon your viewing position(left/right/

top/down). This phenomenon occurs due to the characteristic of the panel. It is not related with the product

performance, and it is not malfunction.

•Avoid touching the screen or holding your finger(s) against it for long periods of time. Doing so may produce some

temporary distortion effects on the screen.

Generated Sound •Cracking noise A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal

contraction due to temperature and humidity. This noise is common for products where thermal deformation is

required.

•Electrical circuit humming/panel buzzing A low level noise is generated from a high-speed switching

circuit, which supplies a large amount of current to operate a product. It varies depending upon the product. This

generated sound does not affect the performance and reliability of the product.

The TV does not turn on

continuously due to Always

Ready mode operation or

does not automatically

turn on by sensor.

•The motion sensor is located on the bottom center of the TV.

•The motion sensor is only supported by some models.

•If there is a foreign substance on the motion sensor, it may not work properly.

•If the environment around the TV is too bright or too dark, the motion sensor may not work properly.

•Obstacles in front of the TV may affect the detection function of the motion sensor.

•It can operate by recognizing changes in lighting around the TV or movement of objects (pets/robot vacuum

cleaners, etc.).

•To stop using the Always Ready mode in → [ ] → [General] → [Always Ready] → [Enable the function],

or to use only the General Always Ready mode function, you can select Enable Always Ready mode, turn off the

screen, and then stop using the motion sensor in [Always Ready Settings]. The screen-on function with the motion

sensor can be set by adjusting the performance of the sensor through the [Always Ready Settings] → [Motion

Sensor Sensitivity] setting.

•Make sure to wring any excess water or cleaner from the cloth.

•Do not spray water or cleaner directly onto the TV screen.

•Make sure to spray just enough of water or cleaner onto a dry cloth to wipe the screen.

Precautions for Protecting the OLED TV Screen

Unlike regular LED/LCDs, OLED TVs produce images that emit light for each

pixel, achieving a perfect black color and delivering clear images without

blurring.

Due to the nature of the organic materials used to achieve high-resolution

image quality, OLED displays generally experience image retention on the

screen, which can be a persistent phenomenon. This phenomenon is observed

in all OLED panels, and although recommended picture modes can minimize

image retention, current technology cannot completely prevent this from

occurring.

Displaying the same image for a long time or repeatedly displaying the

same image can cause image retention on the screen, which is a common

phenomenon in OLED panel products due to the nature of the product. This

product has a built-in screen protection feature. Avoid displaying images that

are likely to cause image retention, and follow the recommendations.

Images that are likely to cause image

retention

•Images with black areas on the top and bottom and/or the left and right

sides of the screen.

•Images whose aspect ratio is 4:3 or 21:9.

•Images that are fixed for a long time, such as channel number, station

logo, game console icon, set-top box menu, etc.

•Other fixed screen images or repeatedly displayed images.

Running [Pixel Cleaning] to Protect the

OLED TV Screen

The OLED TV is equipped with a pixel cleaning feature to check the status of

the screen by itself and prevent image retention that leaves an image on a

screen. This feature automatically calculates the optimal execution time based

on the accumulated viewing time and is automatically executed when the

TV is turned off. While this feature is running, horizontal lines may appear at

the top and bottom of the screen. The pixel cleaning feature works when the

product is connected to the power cord and main power.

•To run this function manually, press the button on the remote

control, go to [ ] → [General] → [OLED Care] → [OLED Panel Care]

and press [Pixel Cleaning].

Recommendations for Minimizing

Image Retention

When watching the TV for a long time, press the button on the remote

control, go to [ ] → [Picture] → [Select Mode] and set the mode to [Auto

Power Save], go to [Advanced Settings] → [Brightness] and set [OLED Pixel

Brightness] to a lower level. In addition, press the button on the remote

control, go to [ ] → [General] → [OLED Care] → [OLED Panel Care] and

set the [Adjust Logo Brightness] value to [High].

When showing images with black bars at the top/bottom/left/right side of

the screen, press the button on the remote control, press [ ], and go to

[Picture] → [Aspect Ratio] → [User Selection] → [Vertical Zoom] or [4-Way

Zoom] to remove the black bars.

Turn off the menus for setting up devices such as set-top boxes so that they

are not displayed on the screen for a long time.

Note

•When the screen is showing one fixed image for a long time, the screen

brightness will be automatically reduced and then restored once the

screen content changes. This is a normal function to minimize image

retention.

Regulatory

(1)

(2)

(3)

(4)

NOTE TO CABLE/TV INSTALLER

(For USA and Canada)

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for

proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable

entry as practical.

WARNING! (STABILITY HAZARD)

A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as:

-ALWAYS use cabinets or stands or mounting methods recommended by the manufacturer of the television set.

-ALWAYS use furniture that can safely support the television set.

-ALWAYS ensure the television set is not overhanging the edge of the supporting furniture.

-ALWAYS educate children about the dangers of climbing on furniture to reach the television set or its controls.

-ALWAYS route cords and cables connected to your television so they cannot be tripped over, pulled or grabbed.

-NEVER place a television set in an unstable location.

-NEVER place the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television set to a

suitable support.

-NEVER place the television set on cloth or other materials that may be located between the television set and supporting furniture.

-NEVER place items that might tempt children to climb, such as toys and remote controls, on the top of the television or furniture on which the television

is placed.

If the existing television set is going to be retained and relocated, the same considerations as above should be applied.

Symbols

Refers to alternating current (AC). Refers to stand-by.

Refers to direct current (DC). Refers to “ON” (power).

Refers to class II equipment. Refers to dangerous voltage.

FRANÇAIS

Sécurité et références

MANUEL DU PROPRIÉTAIRE

Veuillez lire ce manuel attentivement

avant d’utiliser votre appareil et

conservez-le pour pouvoir vous y

reporter ultérieurement.

www.lg.com

Les numéros de modèle et de série du produit sont

situés à l’arrière et sur l’un de ses côtés. Inscrivez-les

ci-dessous au cas où vous auriez besoin d’un service

d’entretien ou de réparation.

Modèle

Numéro de série

OLED55G3PUA

OLED65G3PUA

OLED77G3PUA

OLED83G3PUA

OLED77Z3PUA

Imprimé en Corée

Déclaration de conformité du

fournisseur

Appellation

commerciale

Partie

responsable

LG Electronics USA, inc.

Adresse 111, Sylvan Avenue, North

Building, Englewood Cliffs,

NJ07632

Courriel lg.envir[email protected]

Service à la clientèle LG

Pour toute question ou tout

commentaire, visitez le www.lg.com ou

appelez :

1-888-542-2623 CANADA

1-800-243-0000 États-Unis,

résidentiel

1-888-865-3026

ÉTATS-UNIS,

pour utilisateur

commercial

Enregistrez votre produit en ligne!

www.lg.com

Directives de sécurité importantes

•Lisez ces directives.

•Conservez ces directives.

•Soyez attentif à tous les avertissements.

•Suivez toutes les directives.

•N’utilisez pas cet appareil près de l’eau.

•Nettoyez-le uniquement avec un linge sec.

•Ne bloquez pas les ouvertures d’aération. Installez l’appareil en respectant les directives du fabricant.

•N’installez pas l’appareil près de sources de chaleur comme les radiateurs, les bouches de chaleur, les fours et tout autre appareil (y compris les

amplificateurs) produisant de la chaleur.

•Ne contournez pas la fonctionnalité sécuritaire de la fiche polarisée ou de la prise de mise à la terre. Une fiche polarisée est munie de deux lames, dont l’une

est plus large que l’autre. Une fiche de mise à la terre comporte deux lames et une broche de mise à la terre. La lame la plus large ou la broche de mise à la

terre sont fournies pour votre sécurité. Si la fiche fournie ne s’insère pas dans votre prise, consultez un électricien pour la remplacer.

•Protégez le cordon d’alimentation de manière à ce qu’il ne soit ni piétiné ni pincé, particulièrement près de la fiche, des prises de courant et du point de

sortie de l’appareil.

•N’utilisez que les articles ou les accessoires recommandés par le fabricant.

•Utilisez uniquement avec un chariot, un socle, un trépied ou une table recommandé par le fabricant ou vendu avec l’appareil. Si vous déplacez l’appareil à

l’aide d’un chariot, faites preuve de prudence afin de prévenir les blessures causées par un basculement.

•Débranchez cet appareil pendant les orages électriques ou lorsqu’il n’est pas utilisé pendant de longues périodes.

•Confiez l’ensemble des réparations à du personnel qualifié. Une intervention est nécessaire dans les cas suivants: si la prise ou le cordon d’alimentation est

endommagé, si un liquide a été renversé sur l’appareil ou si des objets sont tombés dans l’appareil, si l’appareil a été exposé à la pluie ou à l’humidité, s’il ne

fonctionne pas normalement ou s’il est tombé.

Avant de lire ce manuel

•Veuillez lire ce manuel attentivement avant d’utiliser votre téléviseur et le conserver pour pouvoir vous y reporter ultérieurement.

•Sur le site Web, vous pouvez télécharger le manuel qui comprend des renseignements sur l’installation, l’utilisation, le dépannage, les caractéristiques, la

licence,etc., et consulter son contenu sur votre ordinateur ou votre appareil mobile.

•Guide d’utilisation : Pour de plus amples renseignements sur ce téléviseur, lisez le MANUEL D’UTILISATION fourni avec le produit. (Selon le modèle)

-Pour ouvrir le GUIDE D’UTILISATION → [ ] → [Assistance] → [Guide d’utilisation].

Articles supplémentaires offerts en option

•Les articles supplémentaires offerts en option peuvent être remplacés ou modifiés à des fins d’amélioration de la qualité, sans préavis. Communiquez avec

votre détaillant pour vous procurer ces articles. Ces dispositifs ne fonctionnent qu’avec certains modèles. Le nom ou la conception du modèle peuvent être

modifiés selon les conditions ou les politiques du fabricant.

•Un câble pour connecter des antennes et des périphériques externes doit être acheté séparément.

Remarques

•Les caractéristiques du produit ou le contenu de ce manuel peuvent être modifiés sans préavis à des fins de mise à niveau des fonctionnalités du produit.

•Les articles fournis avec votre produit peuvent varier selon le modèle.

•L’image présentée peut ne pas correspondre à votre téléviseur.

En utilisant ce produit, vous acceptez que tout différend entre vous et LG relativement à ce produit ou découlant de ce dernier de quelque manière que ce soit

(y compris, sans toutefois s’y limiter, les différends concernant la garantie) se règle exclusivement par arbitrage exécutoire au cas par cas. Les modalités de

l’entente d’arbitrage (y compris les détails sur la procédure de règlement des différends) se trouvent sur les sites www.lg.com/us/arbitration (États-Unis) et

www.lg.com/ca_fr/arbitrage (Canada).

Avertissements! Directives de sécurité

MISE EN GARDE

RISQUE DE DÉCHARGE ÉLECTRIQUE

NE PAS OUVRIR

MISE EN GARDE : AFIN DE RÉDUIRE LE RISQUE DE DÉCHARGE ÉLECTRIQUE, NE RETIREZ PAS LE COUVERCLE (OU LE PANNEAU ARRIÈRE). AUCUNE PIÈCE POUVANT

ÊTRE RÉPARÉE PAR L’UTILISATEUR NE SE TROUVE À L’INTÉRIEUR DE L’APPAREIL. CONFIEZ L’ENTRETIEN DE CET APPAREIL À DU PERSONNEL QUALIFIÉ.

Ce symbole a pour fonction d’alerter l’utilisateur de la présence d’une tension dangereuse non isolée à l’intérieur du boîtier de l’appareil qui pourrait

être d’une puissance suffisante pour causer une décharge électrique.

Ce symbole vise à alerter l’utilisateur de la présence de directives d’utilisation et d’entretien importantes dans la documentation accompagnant

l’appareil.

AVERTISSEMENT: AFIN DE RÉDUIRE LE RISQUE D’INCENDIE ET DE DÉCHARGE ÉLECTRIQUE, N’EXPOSEZ PAS CE PRODUIT À LA PLUIE OU À L’HUMIDITÉ.

•POUR ÉVITER LA PROPAGATION DES FLAMMES, MAINTENEZ À TOUT

MOMENT CE PRODUIT LOIN DES BOUGIES OU D’AUTRES ÉLÉMENTS À

FLAMMES NUES.

•N’installez pas le téléviseur ni la télécommande dans les

environnements suivants:

-En exposition directe à la lumière du soleil.

-Dans une zone avec une forte humidité comme une salle de bains.

-À proximité d’une source de chaleur comme une cuisinière et tout

autre appareil produisant de la chaleur.

-À proximité des comptoirs de cuisine ou des humidificateurs où ils

peuvent facilement être exposés à de la vapeur ou à de l’huile.

-Dans une zone exposée à la pluie ou au vent.

-Dans une zone présentant un risque de ruissellement ou

d’éclaboussure. Évitez de poser des objets contenant du liquide

(p. ex. vase, tasse) sur l’appareil ou au-dessus de celui-ci(p.ex.sur

une tablette).

-À proximité d’objets inflammables comme de l’essence ou des bougies,

ou en exposition directe à un système de climatisation.

-Dans un endroit très poussiéreux.

Cela pourrait entraîner des risques d’incendie, de décharge électrique,

de combustion, d’explosion, de mauvais fonctionnement ou d’altération

du produit.

•Aération

-Installez votre téléviseur à un endroit où l’aération est suffisante. Ne

l’installez pas dans un espace restreint comme une bibliothèque.

-N’installez pas le produit sur un tapis ou un coussin.

-N’obstruez pas les ouvertures de l’appareil et ne le recouvrez pas avec

du tissu ou tout autre matériau lorsqu’il est branché.

•Prenez soin de ne pas toucher aux ouvertures d’aération. Lorsque le

téléviseur fonctionne pendant une longue période, les ouvertures

d’aération peuvent devenir chaudes.

•Protégez le cordon d’alimentation contre les dommages physiques ou

mécaniques. Veillez notamment à ce qu’il ne soit pas tordu, déformé,

pincé, coincé dans une porte ou piétiné. Soyez particulièrement attentif

aux fiches, aux prises de courant murales et à l’emplacement de sortie du

cordon sur l’appareil.

•Ne déplacez pas le téléviseur lorsque le cordon d’alimentation est

branché.

•N’utilisez pas un cordon d’alimentation endommagé ou desserré.

•Assurez-vous de bien saisir la fiche lorsque vous débranchez le

cordon d’alimentation. Ne tirez pas sur le cordon d’alimentation pour

débrancher le téléviseur.

•Ne branchez pas trop d’appareils dans une même prise de courant

alternatif, car cela pourrait causer un incendie ou une décharge

électrique.

•Débranchement de l’appareil de la source d’alimentation

principale

-La fiche d’alimentation permet de débrancher l'appareil. La fiche

d’alimentation doit rester accessible en tout temps afin de pouvoir

débrancher l’appareil en cas d’urgence.

•Ne laissez pas vos enfants grimper sur le téléviseur ou s’agripper dessus.

Autrement, le téléviseur pourrait tomber et causer des blessures graves.

•Mise à la terre d’antennes extérieures (peut varier selon le pays) :

Si une antenne extérieure est installée, prenez les précautions ci-dessous.

Un système d’antennes extérieures ne devrait pas se trouver à proximité

des lignes aériennes d’électricité, d’autres circuits électriques d’éclairage ou

d’alimentation, ou à un endroit où il peut entrer en contact avec de telles

lignes électriques ou de tels circuits d’alimentation; cela pourrait entraîner de

graves blessures ou un décès.

Assurez-vous que le système d’antennes est mis à la terre afin qu’il soit

protégé dans une certaine mesure contre les surtensions et les accumulations

d’électricité statique.

L’article810 du Code national de l’électricité (NEC) des États-Unis fournit des

renseignements relatifs à la procédure conforme de mise à la terre du mât

et de la structure d’appui ainsi que de mise à la terre du câble de connexion

au dispositif de décharge de l’antenne, en plus de renseignements relatifs au

format des conducteurs de terre, à la position du dispositif de décharge de

l’antenne, au branchement des électrodes de masse et aux exigences de mise

à la terre de l’électrode.

Mise à la terre de l’antenne selon le Code national de l’électricité, ANSI/

NFPA70.

•Ne touchez jamais cet appareil ou l’antenne en cas d’orage. Vous pourriez

recevoir une décharge électrique.

•Assurez-vous que le cordon d’alimentation est correctement branché

au téléviseur et à la prise murale. Sinon, la fiche et la prise peuvent être

endommagées, et, dans des cas extrêmes, un incendie peut se produire.

•N’insérez pas d’objets métalliques ou inflammables dans le produit.

Si un corps étranger tombe dans l’appareil, débranchez le cordon

d’alimentation et communiquez avec le service à la clientèle.

•Ne touchez pas l’extrémité du cordon d’alimentation lorsqu’il est

branché. Vous pourriez recevoir une décharge électrique.

•Si l’une des situations énoncées ci-dessous se produit,

débranchez immédiatement le produit et communiquez avec le

service à la clientèle de votre région.

-Si le produit a été endommagé.

-Si de l’eau ou une autre substance s’infiltre dans le produit (dans

l’adaptateur c.a., le cordon d’alimentation ou le téléviseur).

-Si une odeur de fumée ou une odeur étrange se dégage du téléviseur.

-En cas d’orage ou de périodes d’inutilisation prolongées.

Si elle n’est pas débranchée, la source d’alimentation électrique reste

connectée à l’appareil, même lorsque le téléviseur a été éteint au moyen

de la télécommande ou du bouton.

•N’utilisez pas d’appareils électriques à haute tension à proximité du

téléviseur (p.ex. tue-mouches électrique). Cela pourrait entraîner un

mauvais fonctionnement de l’appareil.

•

Ne tentez en aucun cas de réaliser des modifications sur cet appareil sans avoir

obtenu l’autorisation écrite de LGElectronics. Cela pourrait entraîner des risques

d’incendie ou de décharge électrique. Si vous désirez effectuer un entretien ou

une réparation, communiquez avec le service à la clientèle de votre région. Une

modification non autorisée pourrait entraîner la révocation de l’autorisation

d’utilisation de cet appareil.

•

N’utilisez que des pièces supplémentaires ou des accessoires approuvés par

LGElectronics. Sinon, cela pourrait entraîner des risques d’incendie, de décharge

électrique, de mauvais fonctionnement ou d’altération du produit.

•Ne démontez jamais l’adaptateur c.a. ou le cordon d’alimentation.

Cela peut provoquer un incendie ou une décharge électrique.

•Manipulez l’adaptateur avec soin pour éviter de l’échapper ou de le

frapper contre d’autres objets. Un impact pourrait l’endommager.

•Pour réduire les risques d’incendie ou de décharge électrique, ne touchez

pas le téléviseur si vous avez les mains mouillées. Si les broches de la

fiche du cordon d’alimentation sont mouillées ou couvertes de poussière,

séchez ou époussetez la fiche soigneusement.

•Piles

-Rangez les accessoires (piles ou autres) dans un lieu sûr et hors de la

portée des enfants.

-Ne court-circuitez pas les piles, ne les démontez pas et ne les laissez

pas surchauffer. Ne jetez pas les piles dans le feu. Les piles ne doivent

pas être exposées à une chaleur excessive.

-Mise en garde : Il existe un risque d’incendie ou d’explosion si les piles

sont remplacées par un type de pile incompatible.

•Déplacement

-Lorsque vous déplacez l'appareil, assurez-vous qu’il est éteint et

débranché et que tous les câbles ont été retirés. La présence d’au

moins deux personnes peut être requise pour déplacer un téléviseur

de grande taille. N’exercez aucune pression sur le panneau avant du

téléviseur. Cela pourrait endommager le produit ou entraîner des

risques d’incendie ou de blessures.

•Conservez le matériel d’emballage anti-humidité ou l’emballage en

vinyle hors de la portée des enfants.

•Évitez de heurter l’appareil et assurez-vous qu’aucun objet ne tombe

dans celui-ci ou n’entre en contact avec l’écran.

•N’appuyez pas fortement sur l’écran avec votre main ou un objet pointu

(p. ex. ongle, crayon, stylo) et évitez d’égratigner l’écran. Cela pourrait

l’endommager.

•Nettoyage

-Lors du nettoyage, débranchez le cordon d’alimentation et essuyez

l’appareil à l’aide d’un chiffon doux et sec. Ne vaporisez pas d’eau ou

d’autres liquides directement sur le téléviseur. Ne nettoyez pas votre

téléviseur à l’aide de produits chimiques qui peuvent l’endommager

ou endommager son panneau, y compris du nettoyant pour vitres,

tout type de purificateur d’air, de l’insecticide, du lubrifiant, de la cire

(pour voiture ou industrielle), des nettoyants abrasifs, du diluant,

du benzène, de l’alcool, etc. Cela pourrait entraîner des risques de

décharge électrique ou endommager le produit.

Installation

Soulèvement et déplacement du

téléviseur

Lorsque vous désirez déplacer ou soulever le téléviseur, lisez tout d’abord ce

qui suit pour éviter d’égratigner ou d’endommager le téléviseur ainsi que

pour effectuer un transport sécuritaire sans égard au type ni à la taille du

téléviseur.

•Il est recommandé de déplacer le téléviseur en utilisant la boîte ou le

matériel d’emballage d’origine.

•Avant de déplacer ou de soulever le téléviseur, débranchez le cordon

d’alimentation et tous les câbles.

•Lorsque vous manipulez le téléviseur, veillez à ce que l’écran ne soit pas

orienté vers vous pour éviter de l’endommager.

•Tenez fermement le haut et le bas du cadre du téléviseur. Assurez-vous

de ne pas tenir la partie transparente, le haut-parleur ou la grille du

haut-parleur.

•La présence d’au moins deux personnes est requise pour déplacer un

téléviseur de grande taille.

•Lorsque vous transportez le téléviseur, évitez de l’exposer à des chocs ou

à des vibrations excessives.

•Lorsque vous transportez le téléviseur, maintenez-le à la verticale; ne le

tournez jamais sur le côté et ne le penchez ni à gauche ni à droite.

•Lors de la manipulation du téléviseur, veillez à ne pas endommager les

boutons en saillie.

•Évitez de toucher l’écran, car cela pourrait l’endommager.

•Ne déposez pas le produit sur le plancher si la partie avant n’est pas

posée sur une surface coussinée. Cela pourrait endommager l’écran.

•Pour fixer le socle au téléviseur, placez l’écran face contre une table ou

une surface plane matelassée afin de le protéger contre les rayures.

Installation sur une table

1 Soulevez et placez le téléviseur en position verticale sur une table.

• Laissez un espace d’au moins 10cm (4po) entre le mur et le téléviseur

pour assurer une aération adéquate (selon le modèle).

2 Branchez le cordon d’alimentation à une prise murale.

La page charge ...

LG OLED65G3PUA Le manuel du propriétaire

Marque: LG

Modèle: OLED65G3PUA

Catégorie: Téléviseurs LCD

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: LG OLED65G3PUA Owner's manual

LG OLED65G3PUA Le manuel du propriétaire

Ce manuel convient également à

LG OLED65G3PUA Le manuel du propriétaire

dans d''autres langues

Documents connexes