Dell E13S Series Manuel utilisateur

Dell™ PowerEdge™

R510 Systems

Getting Started

With Your System

Guide de mise en route

Primeiros passos com o sistema

Procedimientos iniciales con el sistema

Dell™ PowerEdge™

R510 Systems

Getting Started

With Your System

Regulatory Model E12S Series and E13S Series

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use

of your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data

if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.;

Intel and Xeon are registered trademarks of Intel Corporation in the U.S. and other countries;

Microsoft, Hyper-V, Windows, and Windows Server are either trademarks or registered trademarks

of Microsoft Corporation in the United States and/or other countries; Red Hat and Red Hat Enterprise

Linux are registered trademarks of Red Hat, Inc. in the United States and other countries; SUSE is a

registered trademark of Novell, Inc., in the United States and other countries; VMware and vSphere

are registered trademarks or trademarks (the "Marks") of VMware, Inc. in the United States and/or

other jurisdictions; Citrix and XenServer are trademarks of Citrix Systems, Inc. and/or more of its

subsidiaries, and may be registered in the United States Patent and Trademark Office and in

other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks

and trade names other than its own.

Regulatory Model E12S Series and E13S Series

October 2009 P/N 3YPMN Rev. A00

Getting Started With Your System 3

Installation and Configuration

WARNING: Before performing the following procedure, review the safety

instructions that came with the system.

Unpacking the System

Unpack your system and identify each item.

Assemble the rails and install the system in the rack following the safety

instructions and the rack installation instructions provided with your system.

4 Getting Started With Your System

Optional – Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable

to plug into each connector. Be sure to tighten the screws (if any) on the

monitor's cable connector.

Connecting the Power Cable(s)

Connect the system’s power cable(s) to the system and, if a monitor is used,

connect the monitor’s power cable to the monitor.

Getting Started With Your System 5

Securing the Power Cable(s)

Bend the system power cable into a loop as shown in the illustration and secure

the cable to the bracket using the provided strap. Plug the other end of the

power cable into a grounded electrical outlet or a separate power source such

as an uninterrupted power supply (UPS) or a power distribution unit (PDU).

Turning On the System

Press the power button on the system and the monitor. The power indicators

should light.

6 Getting Started With Your System

Installing the Optional Bezel

Install the bezel (optional).

Complete the Operating System Setup

If you purchased a preinstalled operating system, see the operating system

documentation that ships with your system. To install an operating system

for the first time, see the installation and configuration documentation

for your operating system. Be sure the operating system is installed before

installing hardware or software not purchased with the system.

Supported Operating Systems

NOTE: For twelve–hard-drive systems with additional internal hard drives,

it is recommended that you install the operating system on the internal hard drives

in a RAID 1 configuration.

• Microsoft

®

Windows Server

®

2008 Hyper-V™ Standard (x64) Edition

• Microsoft Windows

®

Small Business Server 2008 Standard

and Premium (x64) Editions

• Microsoft Windows Essential Business Server 2008

Premium (x86) Edition

• Microsoft Windows Essential Business Server 2008 Standard

and Premium (x64) Editions

body.fm Page 6 Tuesday, October 20, 2009 10:43 AM

Getting Started With Your System 7

body.fm Page 7 Tuesday, October 20, 2009 10:44 AM

• Microsoft Windows Server 2008 Standard, Enterprise, and

Datacenter (x64) Editions with SP2 with Hyper-V role enabled

• Microsoft Windows Web Server 2008 with SP2 with Hyper-V role enabled

• Microsoft Windows Server 2008 Standard and Enterprise (x86) Editions

with SP2

• Microsoft Windows Web Server 2008 with SP2

• Microsoft Windows Server 2008 R2 Standard, Enterprise,

and Datacenter (x64) Editions with Hyper-V role enabled

• Microsoft Windows Web Server 2008 R2 with Hyper-V role enabled

• Microsoft Windows HPC Server 2008 R2 (x64) Edition

• Microsoft Windows Server 2003 R2 Standard and Enterprise (x86)

Editions with SP2

• Microsoft Windows HPC Server 2008 (x64) Edition

NOTE: Not supported on twelve–hard-drive systems.

• Microsoft Windows Server 2003 R2 Standard, Enterprise,

and Datacenter (x64) Editions with SP2

•Red Hat

®

Enterprise Linux

®

AS and ES (Version 4.8) (x86_64)

•Red Hat

Enterprise Linux AS and ES (Version 4.8) (x86)

• Red Hat Enterprise Linux Server 5.3 (x86_64)

• Red Hat Enterprise Linux Server 5.3 (x86)

•SUSE

®

Linux Enterprise Server 10 (x86_64) with SP3

• SUSE Linux Enterprise Server 11 (x86_64)

•VMware

®

vSphere™ ESXi Version 4.0

8 Getting Started With Your System

• VMware Virtual Infrastructure 3 ESXi Version 3.5 Update 4

NOTE: VMware Virtual Infrastructure 3 ESXi Version 3.5 Update 4

is not supported on twelve–hard-drive systems.

• Citrix

®

XenServer™ Enterprise (Version 5.5)

NOTE: Twelve–hard-drive systems support Citrix XenServer Enterprise

(Version 6.0).

• Citrix Essentials for XenServer Enterprise (Version 5.5)

NOTE: For the latest information on supported operating systems,

see support.dell.com.

Other Information You May Need

WARNING: See the safety and regulatory information that shipped with

your system. Warranty information may be included within this document

or as a separate document.

• The rack documentation included with your rack solution describes

how to install your system into a rack.

•The

Hardware Owner’s Manual

provides information about system

features and describes how to troubleshoot the system and install or

replace system components. This document is available online at

support.dell.com/manuals

.

• Any media that ships with your system that provides documentation

and tools for configuring and managing your system, including those

pertaining to the operating system, system management software,

system updates, and system components that you purchased

with your system.

NOTE: Always check for updates on support.dell.com/manuals and read the

updates first because they often supersede information in other documents.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does

not perform as expected, see your Hardware Owner’s Manual. Dell™ offers

comprehensive hardware training and certification. See www.dell.com/training

for more information. This service may not be offered in all locations.

Getting Started With Your System 9

Technical Specifications

Processor

Processor type Two Intel

®

Xeon

®

processors 5500 series

Expansion Bus

Bus type PCI Express Generation 2

Expansion slots using riser cards

NOTE: Depending on the configuration, your system may have either riser 1 or riser 2.

Riser 1

OR

Riser 2

Slot 1: PCIe x4, half-length, full-height

Slot 2: PCIe x4, full-length, full-height

Slot 3: PCIe x8, half-length, full-height

Slot 4: PCIe x4, internal slot for integrated card

NOTE: All four slots are x8 connectors.

Slot 1: PCIe x16, full-length, full-height

Slot 2: PCIe x4, internal for integrated card

NOTE: A General Purpose Computation on

Graphics Processing Units (GPGPU) optimized

configuration is available on riser 2.

Memory

Architecture 1066 or 1333 MHz DDR3 registered or

unbuffered Error Correcting Code (ECC)

DIMMs

Memory module sockets Eight 240-pin

Memory module capacities

Four–hard-drive systems

Eight–hard-drive systems

Twelve–hard-drive systems

1 GB, 2 GB, or 4 GB

1 GB, 2 GB, 4 GB, or 8 GB

Minimum RAM 1 GB with a single processor

(1 DIMM per processor)

Maximum RAM

Four–hard-drive systems

Eight–hard-drive systems

Twelve–hard-drive systems

32 GB

64 GB (8 GB dual- and quad-rank DIMMs)

10 Getting Started With Your System

Drives

Hard drives

Four–hard-drive systems

Eight–hard-drive systems

Twelve–hard-drive systems

Up to four 3.5-inch, cabled SAS, SATA,

or SSD drives

Up to eight 3.5-inch or 2.5-inch,

hot-swappable SAS, SATA, or SSD drives

Up to twelve 3.5-inch or 2.5-inch,

hot-swappable SAS, SATA, or SSD drives and

up to two cabled 2.5-inch SAS or SSD drives

NOTE: For twelve–hard-drive systems

with additional internal hard drives, it is

recommended that you install the operating

system on the internal hard drives in a RAID 1

configuration.

Optical drive Optional internal slim-line SATA DVD-ROM

or DVD+/-RW

Optional external USB DVD-ROM

NOTE: Twelve–hard-drive systems support

only an external USB DVD-ROM.

Diskette drive Optional external USB 1.44-MB

Connectors

Back

NIC

Two RJ-45 (for integrated 1-GB NICs)

Serial

9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0-compliant

Video

15-pin VGA

Front

Video

15-pin VGA

USB

Two 4-pin, USB 2.0-compliant

Internal

USB

Two 4-pin, USB 2.0-compliant

body.fm Page 10 Tuesday, October 20, 2009 10:46 AM

Getting Started With Your System 11

Video

Video type Matrox G200, integrated in the BMC

Video memory 8 MB

Power

AC power supply (per power supply)

Wattage

Four–hard-drive systems

Eight–hard-drive systems

Twelve–hard-drive systems

480 W (non-redundant power supply)

750 W/1100 W (optional redundant

power supply)

750 W (optional redundant power supply)

Voltage

100–240 VAC, autoranging, 50–60 Hz

Heat dissipation

Four–hard-drive systems

Eight–hard-drive systems

Twelve–hard-drive systems

1840 BTU/hr maximum

2200 BTU/hr maximum

2450 BTU/hr maximum

Maximum inrush current

Under typical line conditions and over

the entire system ambient operating range,

the inrush current may reach 55 A per

power supply for 10 ms or less.

Batteries

System battery

CR 2032 3.0-V lithium ion coin cell

Physical

Height

Four– and eight– hard-drive

systems

Twelve–hard-drive systems

8.64 cm (3.4 in)

8.67 cm (3.42 in)

Width

Four– and eight–hard-drive

systems

Twelve–hard-drive systems

43.66 cm (17.19 in)

44.52 cm (17.53 in)

12 Getting Started With Your System

Depth

Four– and eight–hard-drive

systems

Twelve–hard-drive systems

61.02 cm (24.09 in)

66.46 cm (26.17 in)

Weight (maximum configuration)

Four–hard-drive systems

Eight–hard-drive systems

Twelve–hard-drive systems

16 kg (35.2 lbs)

22.5 kg (49.5 lbs)

29.0 kg (63.8 lbs)

Weight (empty)

Four–hard-drive systems

Eight–hard-drive systems

Twelve–hard-drive systems

13.6 kg (29.92 lbs)

13.5 kg (29.7 lbs)

15.85 kg (34.87 lbs)

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see www.dell.com/environmental_datasheets.

Temperature

Operating

10° to 35°C (50° to 95°F) with a maximum

temperature gradation of 10°C per hour

NOTE: For altitudes above 2950 feet,

the maximum operating temperature

is derated 1ºF/550 ft.

Storage

–40° to 65°C (–40° to 149°F) with

a maximum temperature gradation

of 20°C per hour

Relative humidity

Operating

20% to 80% (noncondensing) with

a maximum humidity gradation

of 10% per hour

Storage

5% to 95% (noncondensing)

Physical (continued)

Getting Started With Your System 13

Maximum vibration

Operating

0.26 G at 5–350 Hz for 15 min

Storage

1.54 G at 10–250 Hz for 15 min

Maximum shock

Operating

One shock pulse in the positive z axis

(one pulse on each side of the system) of

31 G for 2.6 ms in the operational orientation

Storage

Six consecutively executed shock pulses

in the positive and negative x, y, and z axes

(one pulse on each side of the system)

of 71 G for up to 2 ms

Altitude

Operating

–16 to 3.048 m (–50 to 10,000 ft)

NOTE: For altitudes above 2950 feet,

the maximum operating temperature

is derated 1ºF/550 ft.

Storage

–16 to 10,600 m (–50 to 35,000 ft)

Airborne Contaminant Level

Class

G2 or lower as defined by ISA-S71.04-1985

Environmental (continued)

14 Getting Started With Your System

Systèmes Dell™

PowerEdge™ R510

Guide de mise en route

Modèle réglementaire séries E12S et E13S

Remarques, précautions et avertissements

REMARQUE : Une REMARQUE indique des informations importantes qui peuvent

vous aider à mieux utiliser votre ordinateur.

PRÉCAUTION : Une PRÉCAUTION vous avertit d'un risque de dommage matériel

ou de perte de données en cas de non-respect des instructions données.

AVERTISSEMENT : Un AVERTISSEMENT vous avertit d'un risque d'endom-

magement du matériel, de blessure corporelle ou de mort.

____________________

Les informations contenues dans ce document sont sujettes à modification sans préavis.

La reproduction de ce document de quelque manière que ce soit sans l'autorisation écrite de Dell Inc.

est strictement interdite.

Marques mentionnées dans ce document :

Dell

, le

logo DELL

et

PowerEdge

sont des marques de

Dell Inc. ;

Intel

et

Xeon

sont des marques déposées d'Intel Corporation aux États-Unis et dans d'autres

pays ;

Microsoft, Hyper-V

,

Windows

et

Windows Server

sont des marques ou des marques déposées de

Microsoft Corporation aux États-Unis et/ou d'autres pays ;

Red Hat

et

Red Hat

Enterprise Linux

sont

des marques déposées de Red Hat, Inc. aux États-Unis et dans d'autres pays ;

SUSE

est une marque

déposée de Novell, Inc. aux États-Unis et dans d'autres pays ;

VMware

et

vSphere

sont des marques ou

des marques déposées (les “marques”) de VMware, Inc. aux États-Unis et/ou dans d'autres juridictions ;

Citrix

et

XenServer

sont des marques de Citrix Systems, Inc. et/ou de ses filiales et peuvent être déposées

auprès de l'organisme United States Patent and Trademark Office aux États-Unis et dans d'autres pays.

D'autres marques commerciales et noms de marque peuvent être utilisés dans ce document pour faire

référence aux entités se réclamant de ces marques et de ces noms ou de leurs produits. Dell Inc. dénie

tout intérêt propriétaire vis-à-vis des marques commerciales et des noms de marques autres que les siens.

Modèle réglementaire séries E12S et E13S

Octobre 2009 N/P 3YPMN Rév. A00

Guide de mise en route 17

Installation et configuration

AVERTISSEMENT : Avant de commencer cette procédure, lisez les consignes

de sécurité fournies avec le système.

Déballage du système

Sortez le système de son emballage et identifiez chaque élément.

Assemblez les rails et installez le système dans le rack en suivant les consignes

de sécurité et les instructions d'installation du rack fournies avec votre

système.

18 Guide de mise en route

Facultatif – Connexion du clavier, de la souris et du moniteur

Connectez le clavier, la souris et le moniteur (en option).

Les icônes des connecteurs situées à l'arrière du système indiquent où insérer

chaque câble. N'oubliez pas de serrer les vis situées sur le connecteur du câble

du moniteur, s'il en est équipé.

Branchement du ou des câbles d'alimentation

Branchez le ou les câbles d'alimentation au système et, si vous utilisez

un moniteur, connectez son câble d'alimentation à celui-ci.

La page charge ...

Dell E13S Series Manuel utilisateur

Dell E13S Series Manuel utilisateur

dans d''autres langues

Documents connexes