Campbell Hausfeld CHN71500 Manuel utilisateur

Marque: Campbell Hausfeld

Modèle: CHN71500

Catégorie: Cloueuse

Taper: Manuel utilisateur

Ce manuel convient également à

Pin Nailer

FRANÇAISE: Page 17

ESPAÑOL: Página 33

MAKES IT EASY TO DO IT LIKE A PRO chpower.com

Operating Instructions and Parts Manual

CHN71500

IN730100AV 2/10

Description . . . . . . . . . . . . . . . . . . . . . . . . . 3

Specifications . . . . . . . . . . . . . . . . . . . . . . . 3

Safety Guidelines. . . . . . . . . . . . . . . . . . . . 4

Safety Symbols . . . . . . . . . . . . . . . . . . . . . . 4

Important Safety Information . . . . . . . . 4

Instructions Pertaining to a Risk

of Fire, Electric Shock, or Injury

to Persons. . . . . . . . . . . . . . . . . . . . . . . . . 4

California Proposition 65 . . . . . . . . . . . 4

General . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Work Area. . . . . . . . . . . . . . . . . . . . . . . . . 4

Personal Safety . . . . . . . . . . . . . . . . . . . . 5

Electrical Safety. . . . . . . . . . . . . . . . . . . . 5

Tool Use and Care . . . . . . . . . . . . . . . . . 5

Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Air Source. . . . . . . . . . . . . . . . . . . . . . . . . 6

Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . 6

Contents. . . . . . . . . . . . . . . . . . . . . . . . . . 6

Additional Items Not Included . . . . . . 6

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Getting To Know Your

Pin Nailer Like A Pro. . . . . . . . . . . . . . . . . 8

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Adjustable Exhaust Deflector . . . . . . . 8

No-mar Tip . . . . . . . . . . . . . . . . . . . . . . . 8

Rubber Comfort Grip . . . . . . . . . . . . . . 8

Self-adjusting Pin Length

Mechanism . . . . . . . . . . . . . . . . . . . . . . . 8

Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Lubrication . . . . . . . . . . . . . . . . . . . . . . . 9

Minimum Components Required

for Hook-up. . . . . . . . . . . . . . . . . . . . . . . 9

Hook-up Instructions For Nailer

to Air Supply . . . . . . . . . . . . . . . . . . . . . . 9

Air Hose Requirements. . . . . . . . . . . . . 9

Loading / Unloading The Nailer . . . . 10

Loading the Nailer . . . . . . . . . . . . . . 10

Unloading the Nailer . . . . . . . . . . . . 10

Installing No-Mar Tip . . . . . . . . . . . . . 10

Removing No-Mar Tip . . . . . . . . . . . . 10

Pre-Operation. . . . . . . . . . . . . . . . . . . . . . 11

Operational Modes . . . . . . . . . . . . . . . 11

Sequential Mode. . . . . . . . . . . . . . . . 11

Work Contact Element (WCE). . . . . . 11

Adjusting the Direction of the

Exhaust . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Operation . . . . . . . . . . . . . . . . . . . . . . . . . 12

Firing the Nailer . . . . . . . . . . . . . . . . . . 12

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Maintenance. . . . . . . . . . . . . . . . . . . . . . . 12

Clearing a Jam from the Nailer . . . . . 12

Nailer Repair . . . . . . . . . . . . . . . . . . . . . 12

Replacement Parts. . . . . . . . . . . . . . . . 12

Assembly Procedure for Seals . . . . . . 12

Technical Service . . . . . . . . . . . . . . . . . 12

Fastener Interchange Information. . 13

Troubleshooting Guide . . . . . . . . . . . . . 13

Replacement Parts List

for Brad Nailer . . . . . . . . . . . . . . . . . 14 - 15

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Table of Contents

For parts, product and service information

Visit: www.chpower.com

Call : Customer Service at 1-800-543-6400

Address any correspondence to: Campbell Hausfeld

Attn: Customer Service

100 Production Drive

Harrison, OH 45030 U.S.A.

Operating Instructions and Parts Manual

Pin Nailer

www.chpower.com

Description

This pin nailer is designed for tacking decorative trim, glazing strips, and picture frame

assembly. Features include: convenient side loading magazine which holds up to

135 pins, no-mar tip, oil free, rubber comfort grip, swivel plug, work contact element,

self-adjusting pin length mechanism, and adjustable exhaust.

Figure 1 - CHN71500 Pin Nailer

Specifications

Model CHN71500

Requires: 0.15 Avg SCFM using 10

fasteners per minute at 90 psi

Air Inlet: 1/4 inch NPT

Fastener Size Range:

23g micropins - 3/8 inch to 7/8 inch

Magazine Capacity: 135 fasteners per

load

Weight: 2 lbs.

Length: 9-1/4 inches

Height: 7-1/4 inches

Maximum Pressure: 100 psi

Pressure Range: 60 psi to 100 psi

Locate model number and date code on

magazine and / or tool body. Record below:

Model #: _____________________________

Date Code: ___________________________

Retain these numbers for future reference.

Safety Guidelines

This manual contains

information that is very

important to know and

understand. This information

is provided for SAFETY and

to PREVENT EQUIPMENT

PROBLEMS. To help recognize

this information, observe the

following symbols.

Danger

indicates an

imminently hazardous situation

which, if not avoided, WILL result

in death or serious injury.

Warning

indicates a

potentially hazardous situation

which, if not avoided, COULD

result in death or serious injury.

Caution

indicates a

potentially hazardous situation

which, if not avoided, MAY result in

minor or moderate injury.

Notice

indicates

important information, that if not

followed, may cause damage to

equipment.

NOTE: Information that

requires special attention.

Safety Symbols

The following Safety Symbols

appear throughout this manual

to alert you to important safety

hazards and precautions.

Important Safety Information

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS

This manual contains important safety, operational and maintenance information. If

you have any questions, please call 1-800-543-6400 for customer assistance.

When using tools, basic precautions should always be followed,

including the following:

CALIFORNIA PROPOSITION 65

This product or its power cord may contain chemicals known to the State

of California to cause cancer and birth defects or other reproductive

harm. Wash hands after handling.

You can create dust when you cut, sand, drill or grind

materials such as wood, paint, metal, concrete, cement, or

other masonry. This dust often contains chemicals known to cause cancer, birth

defects, or other reproductive harm. Wear protective gear.

GENERAL

a. To reduce the risks of electric shock, fire, and injury to persons, read

all the instructions before using the tool. Failure to follow warnings,

dangers, and cautions could result in DEATH or SERIOUS INJURY.

b. Be thoroughly familiar with the controls and the proper use of the

equipment. Follow all instructions. Contact your Campbell Hausfeld representative

if you have any questions.

c. Only persons well acquainted with these rules of safe operation should be allowed

to use the unit.

Do not operate or allow anyone else to operate the nailer if any warnings

or warning labels are not legible. Warnings or warning labels are located

on the nailer magazine and body.

Always assume the nailer contains nails. Respect the tool as a working

implement; no horseplay. Always keep others at a safe distance from

the work area in case of accidental discharge of nails. Do not point the tool toward yourself or

anyone whether it contains fasteners or not. Accidental triggering of the nailer could result in

death or serious personal injury.

Do not make any modiﬁcations to the tool without ﬁrst obtaining

written approval from Campbell Hausfeld. Do not use the nailer if any

shields or guards are removed or altered. Do not use the nailer as a hammer. Personal injury or

tool damage may occur.

Clean and check all air supply hoses and ﬁttings before connecting the

nailer to an air supply. Replace any damaged or worn hoses or ﬁttings.

Tool performance or durability may be reduced.

WORK AREA

a. Keep the work area clean and well lighted. Cluttered benches and dark areas

increase the risks of electric shock, fire, and injury to persons.

b. Do not operate the tool in explosive atmospheres, such as in the

presence of flammable liquids, gases, or dust. The tool is able to create

sparks resulting in the ignition of the dust or fumes.

c. Keep bystanders, children, and visitors away while operating the tool.

Distractions are able to result in the loss of control of the tool.

Operating Instructions and Parts Manual

www.chpower.com

Risk of

Personal

Injury

Risk of Fire

Wear Eye

and Mask

Protection

Read Manual

First

Risk of

Explosion

Risk of Falling Wear Eye

Protection

Wear Hearing

Protection

Risk of Shock

CHN71500

ELECTRICAL SAFETY

The front end of the tool may be

made “live” if the tool comes

into contact with live wiring in the wall. TO PREVENT

ACCIDENTAL ELECTRICAL SHOCK, HOLD TOOL ONLY BY

THE SOFT GRIP HANDLE.

TOOL USE AND CARE

a. Do not force the tool. Use the correct tool for the application.

The correct tool will do the job better and safer at the rate for

which the tool is designed.

Disconnect the tool from the air source before

making adjustments, doing tool maintenance,

clearing jams, touching the safety yoke, leaving work area, loading,

or unloading the tool. Such precautionary measures reduce the risk of

injury to persons.

b. Store the tool when it is idle out of reach of children and

other untrained persons. A tool is dangerous in the hands of

untrained users.

c. Maintain the tool with care. A properly maintained tool

reduces the risk of problems and is easier to control.

d. Use only those fasteners listed in the “Fastener Interchange

Information” section on page 12 of this manual. Fasteners

not identified for use with this tool by the tool manufacturer

are able to result in a risk of injury to persons or tool damage

when used in this tool.

e. Always work in a well-ventilated area. Wear OSHA-

approved dust mask.

Always disconnect the tool from the power

source when unattended, performing any

maintenance or repair, clearing a jam, loading, unloading , or moving

the tool to a new location.

Always ﬁt tool with a ﬁtting or hose coupling

on or near the tool in such a manner that all

compressed air in the tool is discharged at the time the ﬁtting or hose

coupling is disconnected. Do not use a check valve or any other ﬁtting

which allows air to remain in the nailer. Death or serious personal

injury could occur.

Never carry the nailer by the air hose or pull

the hose to move the nailer or a compressor.

Keep hoses away from heat, oil and sharp edges. Replace any hose

that is damaged, weak or worn. Personal injury or tool damage could

occur.

Do not drive a nail on top of other nails. The

nail could glance and cause death or a serious

puncture wound.

f. Do not remove any labels from the tool.

g. Do not modify or alter the nailer or any nailer parts. Do

not use the nailer if any shields or guards are removed or

altered. Do not use the nailer as a hammer. Personal injury or

tool damage may occur.

Do not use any type of ﬂammable gases or

oxygen as a power source for the nailer.

Use ﬁltered, lubricated, regulated compressed air only. Use of a

compressed gas instead of compressed air may cause the nailer to

explode which will cause death or serious personal injury.

PERSONAL SAFETY

a. Stay alert. Watch what you are doing and use common

sense when operating the tool. Do not use the tool

while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating the

tool increases the risk of injury to persons.

b. Dress properly. Do not wear loose clothing or jewelry.

Contain long hair. Keep hair, clothing, and gloves away

from moving parts. Loose clothes, jewelry, or long hair

increases the risk of injury to persons as a result of being

caught in moving parts.

c. Do not overreach. Keep proper footing and

balance at all times. Proper footing and balance

enables better control of the tool in unexpected

situations.

d. Use safety equipment. A dust mask, non-skid safety shoes

and a hard hat must be used for the applicable conditions.

Ensuring that the tool is used

only when the operator and all

other personnel in the work area are wearing ANSI Z87

eye protection equipment, and when required, other

appropriate protection equipment such as head, hearing

and foot protection equipment. Serious eye or permanent hearing

loss could result.

e. Always wear hearing protection when using the

tool. Prolonged exposure to high intensity noise

is able to cause hearing loss.

f. Do not attach the hose or tool to your body. Attach the

hose to the structure to reduce the risk of loss of balance if

the hose shifts.

g. Always assume that the tool contains fasteners.

Do not point the tool toward yourself or anyone

whether it contains fasteners or not.

Do not drop or throw the tool. Dropping

or throwing the tool can result in damage that

will make the tool unusable or unsafe. If the tool has been dropped

or thrown, examine the tool closely for bent, cracked or broken parts

and air leaks. STOP and repair before using or serious injury could

occur.

Avoid long extended periods of work with the

nailer. Stop using the nailer if you feel pain in

hands or arms.

Hold tool by insulated gripping surface when

performing an operation where the tool or

fastener may contact hidden wiring. Contacting a “live” wire will

make exposed metal parts of the tool “live” and shock the operator.

Never place hands or any other

body parts in the nail discharge

area of the nailer. The nailer might eject a fastener and

could result in death or serious personal injury.

CHN71500

www.chpower.com

Important Safety Information (Continued)

Operating Instructions and Parts Manual

Important Safety Information (Continued)

Never use gasoline or other ﬂammable liquids

to clean the nailer. Never use the nailer in

the presence of ﬂammable liquids or gases. Vapors could ignite by a

spark and cause an explosion which will result in death or serious

personal injury.

h. Avoid using the nailer when the magazine is empty.

Accelerated wear on the nailer may occur.

Do not modify or disable the Work Contact

Element (WCE). Do not tie or tape the WCE

or trigger in a depressed position. Death or serious personal injury

could result.

Always check that the Work Contact Element

(WCE) is operating properly. A nail could

accidentally be driven if the WCE is not working properly. Personal

injury may occur.

Do not touch the trigger unless driving nails.

Never attach air line to nailer or carry nailer

while touching the trigger. The tool could eject a fastener which will

result in death or serious personal injury.

SERVICE

a. Tool service must be performed only by qualified repair

personnel.

b. When servicing a tool, use only identical replacement

parts. Use only authorized parts.

c. Use only the lubricants supplied with the tool or specified

by the manufacturer.

Disconnect air supply and release tension

from the pusher before attempting to clear

jams because fasteners can be ejected from the front of the nailer.

Personal injury may occur.

AIR SOURCE

a. Never connect to an air source that is capable of exceeding

200 psi. Over pressurizing the tool is able to result in

bursting, abnormal operation, breakage of the tool or

serious injury to persons. Use only clean, dry, regulated

compressed air at the rated pressure or within the rated

pressure range as marked on the tool. Always verify prior to

using the tool that the air source has been adjusted to the

rated air pressure or within the rated air-pressure range.

b. Never use oxygen, carbon dioxide, combustible gases or

any bottled gas as an air source for the tool. Such gases are

capable of explosion and serious injury to persons.

Air compressors providing air to the nailer

should follow the requirements established

by the American National Standards Institute Standard B19.3-1991;

Safety Standard for Compressors for Process Industries. Contact your

air compressor manufacturer for information.

SAVE THESE INSTRUCTIONS

DO NOT DISCARD

Unpacking

After unpacking the unit, inspect carefully for any damage that

may have occurred during transit. Check for loose, missing

or damaged parts. Make sure to tighten fittings, bolts, etc.,

before putting unit into service. Check to be sure all supplied

accessories are enclosed with the unit. In case of questions,

damaged or missing parts, please call 1-800-543-6400 for

customer assistance.

CONTENTS

u Pin Nailer

u 3/4 inch, 23 gauge headless micropins

u Operating Instructions

u Warranty Card

u Carry Bag

u Wrenches

ADDITIONAL ITEMS NOT INCLUDED

u Compressor (must be able to maintain a minimum of 60 psi

when the nailer is being used)

u Air hose

u Small tool for clearing jams

u Threadlock glue

u ANSI Z87 eye protection

u Hearing protection and other personal protective

equipment as required

Assembly

This tool comes fully assembled.

The DANGER, WARNING, CAUTION, and NOTICE

notifications and instructions in this manual cannot

cover all possible conditions and situations that may

occur. It must be understood by the operator that

common sense and caution are factors which cannot

be built into this product, but must be supplied by the

operator.

CHN71500

www.chpower.com

Operating Instructions and Parts Manual

www.chpower.com

CHN71500

Glossary

Become familiar with these terms before operating the unit.

ACTUATE (TOOL) — To cause movement to the tool’s component(s) intended to

drive the fastener.

ACTUATION SYSTEM — The use of a trigger, work contact element (WCE) and/

or other operating control, separately or in combination or sequence, to actuate

the tool.

AIR INLET — The opening in which the compressed air supply is connected,

usually by means of a threaded fitting.

FASTENERS — This pin nailer uses 23g Pin Nails ranging in size from 3/8 inch to

7/8 inch.

MAGAZINE — The part of the nailer that holds the Fasteners.

MAXIMUM AIR PRESSURE — The maximum allowable pressure of compressed

air, as specified by the manufacture, for operating the tool.

NO-MAR TIP — The no-mar tip is designed to eliminate marks caused by the

Work Contact Element (WCE) (see Figure 4). The no-mar tip may be removed

if not required (See REMOVING NO-MAR TIP) or when a slightly deeper

countersink is preferred. Simply slide the no-mar off the WCE.

psi (POUNDS PER SQUARE INCH) —Measurement of the pressure exerted by

the force of the air. The actual psi output is measured by a pressure gauge on the

compressor.

QUICK COUPLER — A quick coupler is designed to work in combination with a

quick plug to quickly and easily join a pneumatic tool to an air hose (see Figure 2).

QUICK PLUG — A quick plug is designed to work in combination with a quick

coupler to quickly and easily join a pneumatic tool to an air hose (see Figure 3).

REGULATOR — A device used to control air pressure to an air operated tool

THREAD LOCK GLUE — A locking glue that is applied to the screw threads

before installing. Prevents the screws from working loose during tool operation.

Figure 2 - Quick Coupler

Figure 3 - Quick Plug

Figure 4

No-mar

Tip

ADJUSTABLE EXHAUST

DEFLECTOR

This tool is equipped with an adjustable

exhaust deflector feature. This allows

for the tool exhaust to be redirected in

any position that is convenient for the

user. Turn the deflector to any direction

desired.

NO-MAR TIP

The tool is fitted with a no-mar tip. To

utilize the no-mar tip, simply slide it over

the tool’s WCE.

RUBBER COMFORT GRIP

The tool is fitted with a rubber comfort

grip. This helps to maintain a steady grip

and prevents fatigue.

SELF-ADJUSTING PIN LENGTH

MECHANISM

The tool is equipped with a convenient

self-adjusting pin length mechanism.

Simply load the desired pins in the

magazine and let the tool self-adjust.

Getting To Know Your Pin Nailer Like A Pro

Figure 5 - Components of the Pin Nailer

CHN71500

www.chpower.com

Operating Instructions and Parts Manual

No-mar

Tip

Trigger

Work Contact

Element (WCE)

Pull-out

Warning

Decal

Swivel Plug

Magazine

Latch

Nail Loading

Area

Adjustable

Exhaust

Deflector

Magazine

Rubber

Comfort

Grip

Operating Instructions and Parts Manual

www.chpower.com

CHN71500

Set-Up

LUBRICATION

This nailer requires NO lubrication for normal operation. However, lubrication will

NOT harm the tool.

The work surface can become damaged by excessive lubrication.

MINIMUM COMPONENTS REQUIRED FOR HOOK-UP

AIR COMPRESSOR: The air compressor must be able to maintain a minimum of 60 psi

when the nailer is being used. An inadequate air supply can cause a loss of power and

inconsistent driving (see Chart 1).

PRESSURE REGULATOR: A pressure regulator is required to control the operating

pressure of the nailer between 60 psi and 100 psi.

AIR SUPPLY HOSE: ALWAYS use air supply hoses with a minimum working pressure

rating equal to or greater than the pressure from the power source, or 150 psi,

whichever is greater. Use 1/4 inch air hose for runs up to 50 feet. Use 3/8 inch air hoses

for 50 ft. run or longer (see Figure 6 and Chart 2).

HOOK-UP INSTRUCTIONS FOR NAILER TO AIR SUPPLY

Figure 8 shows the recommended hookup for the nailer.

NOTE: For better performance, install a 3/8 inch quick plug (1/4 inch NPT threads) with

an inside diameter of 0.315 inch (8 mm) on the nailer and a 3/8 inch quick coupler on

the air hose.

1. With ON/OFF switch in OFF position, plug compressor into electrical outlet.

2. Close pressure regulator by turning all the way to the left. Turn compressor ON and

let it pump all the way up to automatic shut-off pressure.

3. Attach air hose to regulator outlet. Adjust pressure regulator by turning to the right

so that outlet pressure is between 60 psi to 100 psi.

4. Load fasteners into nailer (See Loading/Unloading the Nailer section on page 10).

5. Point the nailer in a safe direction while attaching to air hose.

6. Nailer is ready for use. You may need to adjust outlet pressure to achieve proper

fastener depth.

60 psi Minimum

100 psi Maximum

Chart 1

AIR HOSE REQUIREMENTS

DIAMETER LENGTH OF RUN

1/4 inch Less than 50 feet

3/8 inch Greater than or equal

to 50 feet

Chart 2

Figure 6 - Air Hose Requirements

Interior Diameter

Rated 150 psi or greater

Figure 7 - Recommended Hookup

Tank

Pressure

Gauge

Outlet

Pressure

Gauge

Regulator

Outlet

Regulator

Quick

Coupler

Quick

Plug

Swivel

Plug

Quick

Coupler

Air

Hose

CHN71500

www.chpower.com

Operating Instructions and Parts Manual

LOADING / UNLOADING THE TOOL

Always disconnect the tool from the air supply before loading / unloading fasteners.

Choose which type of fastener you want to use for you project. Additional fasteners can

be found at major home centers.

Loading the Tool

1. Push the latch button. Pull back on the magazine cover fully.

2. Insert a stick of pins into the magazine under the automatic nail length plate. Make

sure pointed ends of pins are resting on bottom ledge of magazine when loading.

Make sure pins are not dirty or damaged. Pins are marked for direction of loading.

3. Push the magazine cover forward until latch engages.

Unloading the Tool

1. Push the latch button. Pull back on the magazine cover fully.

2. Remove the pins from the magazine.

3. Push the magazine cover forward until latch engages.

4. Always unload all fasteners before removing tool from service. Unloading is the

reverse of loading, except always disconnect the air supply before unloading.

INSTALLING NO-MAR TIP

1. Disconnect air supply from nailer.

2. Carefully place no-mar tip over the end of work contact element.

3. Check that the WCE and trigger move up and down freely without sticking or

binding.

REMOVING NO-MAR TIP

1. Disconnect air supply from nailer.

2. Pry no-mar tip away from the work contact element.

Set-Up (Continued)

Figure 8 - Loading the Nailer

Figure 9 - No-mar Tip

No-mar Tip

Work Contact

Element

Operating Instructions and Parts Manual

www.chpower.com

CHN71500

Pre-Operation

OPERATIONAL MODE

Always know the operational mode of the nailer before using. Failure to

know the operational mode could result in death or serious injury.

Sequential Mode

This method is recommended when precise nail placement is required. Operation in

this mode requires trigger to be pulled each time a nail is driven. Nailer can be actuated

by depressing the Work Contact Element (WCE) against work surface followed by

pulling the trigger. The trigger must be released after each fastener is driven to allow

tool to reset.

WORK CONTACT ELEMENT (WCE)

Check the operation of the Work Contact Element (WCE) trip mechanism

before each use. The WCE must move freely without binding through its

entire travel distance. The WCE spring must return the WCE to its fully extended position after

being depressed. Do not operate the nailer if the WCE trip mechanism is not operating properly.

Personal injury may occur.

1. Disconnect the air supply from the nailer.

2. Make sure the trigger and Work Contact Element (WCE) move freely up and down

without sticking or binding.

3. Reconnect air supply to the nailer.

4. Use a scrap piece of wood as a work surface.

5. Depress the WCE against the work surface without pulling the trigger (See

Figure 11). The nailer MUST NOT OPERATE. Do not use the tool if it operates

without pulling the trigger. Personal injury may result.

6. Remove nailer from work surface. The WCE must return to its original down

position. Pull the trigger (See Figure 12). The nailer MUST NOT OPERATE. Do not

use the tool if it operates while lifted from the work surface. Personal injury may

result.

7. Pull the trigger and depress the WCE against the work surface. The nailer MUST

NOT OPERATE.

8. Depress the WCE against work surface. Pull the trigger. The nailer MUST OPERATE.

ADJUSTING THE DIRECTION OF THE EXHAUST

The tool is equipped with an adjustable direction exhaust deflector. This is intended to

allow the user to change the direction of the exhaust. Simply twist the deflector to any

direction desired (See Figure 13).

Figure 10 - Sequential Mode

Then pull trigger.

Work Surface

Depress WCE first...

Work Surface

Figure 12

Work Surface

Figure 11

FIRING THE NAILER

1. Load fasteners (see Loading / Unloading the Nailer section).

2. Connect the air supply to the nailer.

An improperly functioning tool must not be used. Do not actuate

the tool unless the tool is placed ﬁrmly against the work piece.

In Sequential Mode

1. Fully depress WCE.

2. Pull trigger. Fastener will be driven into workpiece.

Storage

The nailer should be stored in a cool dry location.

Operation

Figure 15

CHN71500

www.chpower.com

Operating Instructions and Parts Manual

Figure 14

Then pull trigger.

Work Surface

Depress WCE first...

Work Surface

Maintenance

CLEARING A JAM FROM THE NAILER

1. Disconnect nailer from air supply.

2. Remove all nails from the magazine (see Loading/ Unloading). Failure to do so may

cause the nails to eject from the front of the nailer.

3. Completely remove the three (3) small nose screws and the top nose plate to reveal

the jammed fastener.

4. Using caution not to bend or damage the driver blade, use a pick or some other

pointed object to pry free and clear the jammed fastener.

NAILER REPAIR

Only qualified personnel should repair the tool and they should use genuine Campbell

Hausfeld replacement parts and accessories, or parts and accessories which perform

equivalently.

REPLACEMENT PARTS

Use only genuine Campbell Hausfeld service parts. Tool performance,

safety and durability could be reduced if improper parts are used. When

ordering replacement parts, specify by part number.

ASSEMBLY PROCEDURE FOR SEALS

When repairing a nailer, the internal parts must be cleaned and lubricated. Parker

O-lube or equivalent must be used on all o-rings. Each o-ring must be coated with

O-lube before assembling. A small amount of oil must be used on all moving surfaces

and pivots.

TECHNICAL SERVICE

For information regarding the operation or repair of this product, please call

1-800-543-6400.

Operating Instructions and Parts Manual

FASTENER INTERCHANGE INFORMATION

Can use 3/8 inch to 7/8 inch pins from the following branded 23 g micropinners:

• Senco FP10

• Air Locker P630

• Porter Cable PIN100

• Grex P635

• Max NF235A

Maintenance (Continued)

www.chpower.com

CHN71500

Troubleshooting Guide

Stop using nailer immediately if any of the following problems occur. Serious personal injury could result.

Any repairs or replacements must be done by a Qualiﬁed Service Person or Authorized Service Center.

SYMPTOM CAUSE SOLUTION

Air leaking at trigger valve

area.

O-Rings in trigger valve housing are

damaged

Replace o-rings

Air leaking between housing

and nose.

1. Damaged o-rings 1. Replace o-rings

2. Damage to bumper 2. Replace bumper

Air leaking between housing

and cap.

1. Loose screws 1. Tighten screws

2. Damaged seal 2. Replace seal

Tool skips driving fastener 1. Worn bumper 1. Replace bumper

2. Dirt in nose piece 2. Clean drive channel

3. Dirt or damage prevent fasteners

or pusher from moving freely in

magazine

3. Clean magazine

4. Damaged pusher spring 4. Replace spring

5. Inadequate air flow to tool 5. Check fitting, hose, or compressor

6. Worn o-rings on piston or lack of

lubrication

6. Replace and lubricate o-rings

7. Damaged o-rings on trigger valve 7. Replace o-rings

8. Air leaks 8. Tighten screws and fittings

9. Cap seal leaking 9. Replace seal

10. Defect in automatic nail length plate 10. Clear problem with plate

Tool runs slow or has loss of

power

1. Tool not lubricated sufficiently 1. Lubricate nailer

2. Broken spring in cylinder cap 2. Replace spring

3. Exhaust port in cap is blocked 3. Replace damaged internal parts

Fasteners are jammed in tool 1. Guide on driver is worn 1. Replace guide

2. Fasteners are not correct size 2. Use only recommended fasteners

3. Fasteners are bent 3. Replace with undamaged fasteners

4. Magazine or nose screws are loose 4. Tighten screws

5. Driver is damaged 5. Replace driver

Operating Instructions and Parts Manual

For Replacement Parts or Technical Assistance, Call 1-800-543-6400

Please provide following information: Address any correspondence to:

- Model number Campbell Hausfeld

- Serial number (if any) Attn: Customer Service

- Part description and number as shown in parts list 100 Production Drive

Harrison, OH 45030 U.S.A.

Figure 16 – Repair Parts Illustration for Air Powered Pin Nailer, model CHN71500AV

CHN71500

www.chpower.com

CHN71500

Replacement Parts List for Brad Nailer

1 Exhaust deflector — 1

2 Socket head cap

screw - M4 x 16 k 4

3 Cylinder head cap — 1

4 Gasket n 1

5 Exhaust seal n 1

6 Spring n 1

7 O-ring n 1

8 Head valve — 1

9 O-ring n 1

10 O-ring n 1

11 O-ring n 1

12 Collar — 1

13 Piston ring s 1

14 O-ring s 1

15 Piston s 1

16 Driver blade s 1

17 O-ring n 1

18 Cylinder — 1

19 O-ring n 1

20 Restrictor plate — 1

21 Bumper n 1

22 Body — 1

23 Nozzle n 1

24 Spring pin n 2

25 Work contact element (WCE)

bracket — 1

26 WCE spring n 1

27 WCE — 1

28 No-mar tip n 1

29 Trigger valve head — 1

30 Valve seal n 1

31 Trigger valve — 1

32 O-ring n 1

33 Trigger valve stem spring n 1

34 Upper drive guide — 1

35 Drive guide cover — 1

36 Socket head cap

screw - M4 x 8 k 5

37 Trigger valve stem — 1

38 O-ring n 2

39 Trigger spring n 1

40 Trigger assembly — 1

41 Retaining o-ring — 2

42 Pin — 1

43 Socket head cap

screw - M4 x 14 k 2

44 Socket head cap

screw - M4 x 14 k 2

45 Lower driver guide — 1

46 Recoil decal housing — 1

47 Straight pin — 2

48 Magazine — 1

49 Screw - M4 x 10 k 2

50 Magazine slide plate — 1

Ref. Part

No. Description Number Qty.

Ref. Part

No. Description Number Qty.

51 Magazine plate — 1

52 Spring pin — 2

53 Limiter assembly — 1

54 Pusher — 1

55 Pusher seat — 1

56 Spring pin k 1

57 Magazine door — 1

58 Shoulder pins — 2

59 Pusher spring n 1

60 Spring n 1

61 Socket head cap

screw - M4 x 10 k 2

62 Magazine end cap — 1

63 Magazine cap spring n 1

64 Magazine thumb latch — 1

65 Pin — 1

66 Socket head cap

screw - M4 x 18 k 1

67 Washer — 1

68 Washer — 1

69 Magazine bracket — 1

70 Hand grip — 1

71 Nut - M4 k 1

72 O-ring n 1

73 Inlet end cap — 1

74 1/4 - 18 I/M (M) Swivel plug SV567600AV 1

REPLACEMENT PARTS KITS

s Drive blade assembly SKN19900AV

n Complete rebuild kit SKN23900AV

— Not Available

k Standard hardware item - available at your local

hardware store

Operating Instructions and Parts Manual

www.chpower.com

Operating Instructions and Parts Manual

Reminder: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.

Warranty

1. DURATION: From the date of purchase by the original purchaser as follows: One (1) Year.

2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison,

Ohio, 45030, Telephone: (800) 543-6400

3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell

Hausfeld product.

4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: This Campbell Hausfeld nailer or stapler.

5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the

duration of the warranty period with the exceptions below.

6. WHAT IS NOT COVERED UNDER THIS WARRANTY:

A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM

THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this product is used for commercial, industrial or

rental purposes, the warranty will apply for ninety (90) days from the date of purchase. Some States do not allow limitation

on how long an implied warranty lasts, so the above limitations may not apply to you.

B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY

DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the

exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with

instructions provided in the owner’s manual(s) supplied with product. Accident, purchaser’s abuse, neglect or failure to

operate products in accordance with instructions shall also include the removal or alteration of any safety devices. If such

safety devices are removed or altered, this warranty is void.

D. Normal adjustments which are explained in the owner’s manual(s) provided with the product.

E. Items or service that are normally required to maintain the product, e.g. o-rings, springs, bumpers, debris shield, driver

blades, gaskets, packings or seals, lubricants, or any other expendable part not specifically listed. These items will only be

covered for ninety (90) days from date of original purchase. Underlined items are warranted for defects in material and

workmanship only.

7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or

components which are defective, have malfunctioned and/or failed to conform within the duration of the specific warranty

period.

8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A. Provide dated proof of purchase and maintenance records.

B. Call Campbell Hausfeld (800) 543-6400 to obtain your warranty service options. Freight costs must be borne by the

purchaser.

C. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).

9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will

be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of

replacement parts.

This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal rights. You may also have

other rights which vary from state to state or country to country.

CHN71500

www.chpower.com

Cloueuse de pointes

ENGLISH: Page 1

ESPAÑOL: Página 33

VOUS PERMET DE LE FAIRE COMME UN PROFESSIONNEL

Instructions d’Utilisation et Manual de Pièces

CHN71500

IN730100AV 2/10

Description . . . . . . . . . . . . . . . . . . . . . . F-19

Spécifications . . . . . . . . . . . . . . . . . . . . F-19

Directives de sécurité . . . . . . . . . . . . . F-20

Symboles de sécurité . . . . . . . . . . . . . F-20

Information importante

sur la sécurité . . . . . . . . . . . . . . . . . . . . F-20

Instructions portant sur un risque

d’incendie, un choc électrique ou

des blessures aux personnes . . . . . F-20

Proposition 65 de Californie . . . . . F-20

Généralités. . . . . . . . . . . . . . . . . . . . . F-20

Aire de travail . . . . . . . . . . . . . . . . . . F-20

Sécurité personnelle . . . . . . . . . . . . F-21

Sécurité électrique . . . . . . . . . . . . . . F-21

Utilisation et entretien de l’outil. . F-21

Service. . . . . . . . . . . . . . . . . . . . . . . . . F-22

Source d’air . . . . . . . . . . . . . . . . . . . . F-22

Déballage. . . . . . . . . . . . . . . . . . . . . . . . F-22

Contenu . . . . . . . . . . . . . . . . . . . . . . . F-22

Autres articles non inclus. . . . . . . . F-22

Assemblage . . . . . . . . . . . . . . . . . . . . . . F-22

Glossaire . . . . . . . . . . . . . . . . . . . . . . . . F-23

Apprendre à connaître sa cloueuse de

pointes comme un professionnel . . F-24

Caractéristiques. . . . . . . . . . . . . . . . . . F-24

Déflecteur d’échappement

ajustable . . . . . . . . . . . . . . . . . . . . . . . F-24

Embout anti-marques. . . . . . . . . . . F-24

Prise confortable de caoutchouc . .F-24

Mécanisme auto-ajustable

de longueur de pointes . . . . . . . . . . F-24

Installation . . . . . . . . . . . . . . . . . . . . . . F-25

Lubrification . . . . . . . . . . . . . . . . . . . F-25

Composants minimaux requis

pour le raccord . . . . . . . . . . . . . . . . . F-25

Instructions de branchement de la

cloueuse à l’alimentation d’air . . . F-25

Exigences du tuyau à air . . . . . . . . . F-25

Charger/décharger de l’outil. . . . . F-26

Charger de l’outil . . . . . . . . . . . . . F-26

Décharger de l’outil . . . . . . . . . . . F-26

Installer l’embout anti-marques. . F-26

Retirer l’embout anti-marques. . . F-26

Pré-opération . . . . . . . . . . . . . . . . . . . . F-27

Modes d’opération. . . . . . . . . . . . . . F-27

Mode séquentiel . . . . . . . . . . . . . . F-27

Pointe de contact (PC) . . . . . . . . . . F-27

Ajuster la direction

de l’échappement . . . . . . . . . . . . . . F-27

Fonctionnement . . . . . . . . . . . . . . . . . F-28

Utiliser la cloueuse. . . . . . . . . . . . . . F-28

Rangement . . . . . . . . . . . . . . . . . . . . . . F-28

Entretien . . . . . . . . . . . . . . . . . . . . . . . . F-28

Débloquer la cloueuse . . . . . . . . . . F-28

Réparation de la cloueuse . . . . . . . F-28

Pièces de rechange. . . . . . . . . . . . . . F-28

Procédure d’assemblage pour

les joints . . . . . . . . . . . . . . . . . . . . . . . F-28

Service technique. . . . . . . . . . . . . . . F-28

Information sur les attaches

interchangeables . . . . . . . . . . . . . . . F-29

Guide de dépannage. . . . . . . . . . . . . . F-29

Liste de pièces de rechange pour

la cloueuse de pointes

de vitrier. . . . . . . . . . . . . . . . . . F-30 - F-31

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . F-32

Table des Matières

Pour l’information sur les pièces, produits et services

Appeler:

Service à la clientèle au 1-800-543-6400

Adresser toute correspondAnce à : Campbell Hausfeld

Attn: Customer Service

100 Production Drive

Harrison, OH 45030 U.S.A.

Spécifications

Modèle CHN71500

Exigences : 0,004 m³/min (0,3 PCNM)

utilisant 10 attaches à la minute à

621 kPa (90 lb/po²)

Prise d’air : 1/4 po NPT

Plage de tailles d’attaches :

micro pointes de 23 g - 9,5 mm à 22,2

mm (3/8 po à 7/8 po)

Capacité du chargeur : 135 attaches

par charge

Poids : 0,91 kg (2 lbs)

Longueur : 23,50 cm (9-1/4 po)

Hauteur : 18,42 cm (7-1/4 po)

Pression Maximale : 690 kPa

Gamme de Pression : 414 kPa -

690 kPa

Trouver le numéro de modèle et le code de

date sur le chargeur et/ou le corps de l’outil.

Inscrire plus bas :

Nº du Modèle : ________________________

Code Date : ___________________________

Conserver ces numéros comme référence.

Instructions d’Utilisation et Manual de Pièces

Cloueuse de pointes

F-19

Description

Cette cloueuse de pointes est conçue pour l’assemblage de garnitures décoratives,

bandes de vitrage et petits cadres. Caractéristiques: pratique chargeur à chargement

latéral convenant pour 135 pointes, embout anti-marques, sans huile, prise confortable

de caoutchouc, fiche pivotante, pointe de contact, mécanisme auto-ajustable de

longueur de pointes et échappement ajustable.

Figure 1 - CHN71500 Cloueuse de pointes

Importantes Instructions De Sécurité

Instructions Portant Sur Un Risque d’Incendie, Un Choc Électrique Ou Des

Blessures Aux Personnes

Ce manuel contient des informations concernant la sécurité, le fonctionnement et

l’entretien. Si vous avez des questions, appeler le 1-800-543-6400 pour le service à la

clientèle.

En utilisant les outils, il faut suivre les précautions de base, y compris ce

qui suit :

PROPOSITION 65 DE CALIFORNIE

Ce produit ou son cordon peuvent contenir des produits chimiques

qui, de l’avis de l’État de Californie, causent le cancer et des anomalies

congénitales ou autres problèmes de reproduction. Lavez-vous les mains après la manipulation.

Vous pouvez créer de la poussière en coupant, ponçant,

perçant ou meulant les matériaux tels que le bois, la

peinture, le métal, le béton, le ciment ou autre maçonnerie. Cette poussière contient

souvent des produits chimiques reconnus pour causer le cancer, les déformations

congénitales

GÉNÉRALITÉ :

a. Pour réduire les risques de chocs électriques, d’incendie ou de

blessures aux personnes, lire toutes les instructions avant d’utiliser

l’outil. Ne pas suivre les avertissements, les dangers et les mises en

garde pourrait causer la MORT ou de GRAVES BLESSURES.

b. Se familiariser avec ce produit, ses commandes et son utilisation.

Suivez toutes les instructions. Contacter votre représentant Campbell Hausfeld si

vous avez des questions.

c. Seules les personnes familières avec ces règles d’utilisation sans danger devraient

utiliser cette unité.

Ne pas utiliser la cloueuse ni permettre qu’une autre personne l’utilise

si les avertissements ou les étiquettes d’avertissement situés sur le

chargeur et corps de la cloueuse ne sont pas lisibles.

Toujours prendre pour acquis que la cloueuse contient des clous.

Respecter l’outil comme accessoire de travail non pas un jouet. Donc

aucun jeu brutal. Toujours garder les autres personnes à une distance de sécurité de l’aire

de travail en cas de décharge accidentelle des clous. Ne pas pointer l’outil vers vous ou vers

quelqu’un d’autre qu’il y ait ou non des attaches dans la cloueuse. Le déclenchement accidentel

de la cloueuse pourrait causer la mort ou de graves blessures.

Ne pas apporter de modiﬁcations à l’outil sans d’abord obtenir

une approbation écrite de Campbell Hausfeld. N’utilisez pas une

cloueuse si les écrans ou protecteurs ont été enlevés ou altérés. Ne pas utiliser la cloueuse comme

un marteau. Cela peut entraîner des blessures ou endommager l’appareil.

Nettoyer et vériﬁer tous les tuyaux et raccords avant de brancher la

cloueuse au compresseur d’air. Remplacer les tuyaux ou les raccords

endommagés ou usés, sinon, le rendement et la durabilité de l’outil seront affectés.

AIRE DE TRAVAIL

a. Garder l’aire de travail propre et bien éclairée. Les établis encombrés et les coins

sombres augmentent les risques de chocs électriques, d’incendie et de blessures

aux personnes.

b. Ne pas faire fonctionner l’outil dans une atmosphère explosive comme

en présence de liquides, gaz ou poussières inflammables. L’outil peut

produire des étincelles menant à une inflammation de poussières ou de

fumées.

c. Garder les spectateurs, les enfants et les visiteurs loin en utilisant

l’outil. Les distractions peuvent faire perdre le contrôle de l’outil.

Instructions d’Utilisation et Manual de Pièces

Directives de Sécurité

Ce manuel contient de

l’information très importante qui

est fournie pour la SÉCURITÉ et

pour ÉVITER LES PROBLÈMES

D’ÉQUIPEMENT. Rechercher

les symboles suivants pour cette

information.

Danger indique

une situation

dangereuse imminente qui MÈNERA à

la mort ou à des blessures graves si elle

n’est pas évitée.

Avertissement

indique une

situation potentiellement dangereuse

qui, si elle n’est pas évitée, POURRAIT

mener à la mort ou à de graves

blessures.

Attention

indique une

situation potentiellement dangereuse

qui, si elle n’est pas évitée, PEUT mener

à des blessures mineures ou modérées.

Avis indique

de l’information

importante qui pourrait endommager

l’équipement si elle n’est pas respectée.

REMARQUE : Information qui exige

une attention spéciale.

Symboles de sécurité

Les symboles de sécurité suivants

apparaissent dans l’ensemble de

ce manuel pour vous aviser des

dangers et précautions importants

de sécurité.

Risque de

tomber

Porter une

protection

oculaire et un

masque.

Risque

d’explosion

Porter une

protection

auditive

Porter une

protection

oculaire.

Risque de

blessure

Lire le manuel

d’abord

Risque

d’incendie

Risque de choc

CHN71500

F-20

La page charge ...

Campbell Hausfeld CHN71500 Manuel utilisateur

Marque: Campbell Hausfeld

Modèle: CHN71500

Catégorie: Cloueuse

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Campbell Hausfeld CHN71500 User manual
español: Campbell Hausfeld CHN71500 Manual de usuario

Campbell Hausfeld CHN71500 Manuel utilisateur

Ce manuel convient également à

Campbell Hausfeld CHN71500 Manuel utilisateur

dans d''autres langues

Documents connexes