Lincoln Electric Red-D-Arc EX350i Mode d'emploi

Marque: Lincoln Electric

Modèle: Red-D-Arc EX350i

Catégorie: Système de soudage

Taper: Mode d'emploi

RED-D-ARC

EX350

IM764-A

November, 2007

Red-D-Arc Spec-Built Welding Equipment

This RED-D-ARC welder is built to RED-D-ARC

Extreme Duty

design specifications by Lincoln Electric.

Safety Depends on You

This welder is designed and built with safety in mind.

However, your overall safety can be increased by proper installation

... and thoughtful operation on your part.

DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT

WITHOUT READING THIS MANUAL AND THE SAFETY

PRECAUTIONS CONTAINED THROUGHOUT.

And, most importantly, think before you act and be careful.

For use with machines having Code Numbers:

10945, 11487

North Americaʼs Largest Fleet of Welding Equipment

1-800-245-3660

OPERATORʼS MANUAL

FOR ENGINE

powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance

work unless the maintenance work requires it to be running.

____________________________________________________

1.b. Operate engines in open, well-ventilated

areas or vent the engine exhaust fumes

outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame

welding arc or when the engine is running.

Stop the engine and allow it to cool before

refueling to prevent spilled fuel from vaporiz-

ing on contact with hot engine parts and

igniting. Do not spill fuel when filling tank. If

fuel is spilled, wipe it up and do not start

engine until fumes have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers and devices in

position and in good repair.Keep hands, hair, clothing and

tools away from V-belts, gears, fans and all other moving

parts when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety

guards to perform required maintenance. Remove

guards only when necessary and replace them when the

maintenance requiring their removal is complete.

Always use the greatest care when working near moving

parts.

___________________________________________________

1.f. Do not put your hands near the engine fan.

Do not attempt to override the governor or

idler by pushing on the throttle control rods

while the engine is running.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while

turning the engine or welding generator during maintenance

work, disconnect the spark plug wires, distributor cap or

magneto wire as appropriate.

SAFETY

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.

KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you

purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box

351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available

from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE

PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

WARNING

Mar ʻ95

ELECTRIC AND

MAGNETIC FIELDS

may be dangerous

2.a. Electric current flowing through any conductor causes

localized Electric and Magnetic Fields (EMF). Welding

current creates EMF fields around welding cables and

welding machines

2.b. EMF fields may interfere with some pacemakers, and

welders having a pacemaker should consult their physician

before welding.

2.c. Exposure to EMF fields in welding may have other health

effects which are now not known.

2.d. All welders should use the following procedures in order to

minimize exposure to EMF fields from the welding circuit:

2.d.1.

Route the electrode and work cables together - Secure

them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and

work cables. If the electrode cable is on your right

side, the work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as

possible to the area being welded.

2.d.5. Do not work next to welding power source.

1.h. To avoid scalding, do not remove the

radiator pressure cap when the engine is

hot.

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel engine exhaust and some of its constituents

are known to the State of California to cause can-

cer, birth defects, and other reproductive harm.

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

The Above For Diesel Engines

The Above For Gasoline Engines

SAFETY

ARC RAYS can burn.

4.a. Use a shield with the proper filter and cover

plates to protect your eyes from sparks and

the rays of the arc when welding or observing

open arc welding. Headshield and filter lens

should conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant

material to protect your skin and that of your helpers from

the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammable

screening and/or warn them not to watch the arc nor expose

themselves to the arc rays or to hot spatter or metal.

ELECTRIC SHOCK can

kill.

3.a. The electrode and work (or ground) circuits

are electrically “hot” when the welder is on.

Do not touch these “hot” parts with your bare

skin or wet clothing. Wear dry, hole-free

gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.

Make certain the insulation is large enough to cover your full

area of physical contact with work and ground.

In addition to the normal safety precautions, if welding

must be performed under electrically hazardous

conditions (in damp locations or while wearing wet

clothing; on metal structures such as floors, gratings or

scaffolds; when in cramped positions such as sitting,

kneeling or lying, if there is a high risk of unavoidable or

accidental contact with the workpiece or ground) use

the following equipment:

• Semiautomatic DC Constant Voltage (Wire) Welder.

• DC Manual (Stick) Welder.

• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,

electrode reel, welding head, nozzle or semiautomatic

welding gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electrical

connection with the metal being welded. The connection

should be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical

(earth) ground.

3.f.

Maintain the electrode holder, work clamp, welding cable and

welding machine in good, safe operating condition. Replace

damaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts of

electrode holders connected to two welders because voltage

between the two can be the total of the open circuit voltage

of both welders.

3.i. When working above floor level, use a safety belt to protect

yourself from a fall should you get a shock.

3.j. Also see Items 6.c. and 8.

FUMES AND GASES

can be dangerous.

5.a. Welding may produce fumes and gases

hazardous to health. Avoid breathing these

fumes and gases.When welding, keep

your head out of the fume. Use enough

ventilation and/or exhaust at the arc to keep

fumes and gases away from the breathing zone. When

welding with electrodes which require special

ventilation such as stainless or hard facing (see

instructions on container or MSDS) or on lead or

cadmium plated steel and other metals or coatings

which produce highly toxic fumes, keep exposure as

low as possible and below Threshold Limit Values (TLV)

using local exhaust or mechanical ventilation. In

confined spaces or in some circumstances, outdoors, a

respirator may be required. Additional precautions are

also required when welding on galvanized steel.

5. b. The operation of welding fume control equipment is affected

by various factors including proper use and positioning of

the equipment, maintenance of the equipment and the spe-

cific welding procedure and application involved. Worker

exposure level should be checked upon installation and

periodically thereafter to be certain it is within applicable

OSHA PEL and ACGIH TLV limits.

5.c.

Do not weld in locations near chlorinated hydrocarbon

vapors

coming from degreasing, cleaning or spraying operations.

The heat and rays of the arc can react with solvent vapors

form phosgene, a highly toxic gas, and other irritating prod-

ucts.

5.d. Shielding gases used for arc welding can displace air and

cause injury or death. Always use enough ventilation,

especially in confined areas, to insure breathing air is safe.

5.e. Read and understand the manufacturerʼs instructions for this

equipment and the consumables to be used, including the

material safety data sheet (MSDS) and follow your

employerʼs safety practices. MSDS forms are available from

your welding distributor or from the manufacturer.

5.f. Also see item 1.b.

AUG 06

iii

SAFETY

iii

FOR ELECTRICALLY

powered equipment.

8.a. Turn off input power using the disconnect

switch at the fuse box before working on

the equipment.

8.b. Install equipment in accordance with the U.S. National

Electrical Code, all local codes and the manufacturerʼs

recommendations.

8.c. Ground the equipment in accordance with the U.S. National

Electrical Code and the manufacturerʼs recommendations.

CYLINDER may explode

if damaged.

7.a. Use only compressed gas cylinders

containing the correct shielding gas for the

process used and properly operating

regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for

the application and maintained in good condition.

7.b. Always keep cylinders in an upright position securely

chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

• Away from areas where they may be struck or subjected to

physical damage.

• A safe distance from arc welding or cutting operations and

any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other

electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet

when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand

tight except when the cylinder is in use or connected for

use.

7.g. Read and follow the instructions on compressed gas

cylinders, associated equipment, and CGA publication P-l,

“Precautions for Safe Handling of Compressed Gases in

Cylinders,” available from the Compressed Gas Association

1235 Jefferson Davis Highway, Arlington, VA 22202.

Jan, 07

WELDING and CUTTING

SPARKS can

cause fire or explosion.

6.a.

Remove fire hazards from the welding area.

If this is not possible, cover them to prevent

the welding sparks from starting a fire.

Remember that welding sparks and hot

materials from welding can easily go through small cracks

and openings to adjacent areas. Avoid welding near

hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site,

special precautions should be used to prevent hazardous

situations. Refer to “Safety in Welding and Cutting” (ANSI

Standard Z49.1) and the operating information for the

equipment being used.

6.c. When not welding, make certain no part of the electrode

circuit is touching the work or ground. Accidental contact

can cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the

proper steps have been taken to insure that such procedures

will not cause flammable or toxic vapors from substances

inside. They can cause an explosion even

though

they have

been “cleaned”. For information, purchase “Recommended

Safe Practices for the

Preparation

for Welding and Cutting of

Containers and Piping That Have Held Hazardous

Substances”, AWS F4.1 from the American Welding Society

(see address above).

6.e. Vent hollow castings or containers before heating, cutting or

welding. They may explode.

6.f.

Sparks and spatter are thrown from the welding arc. Wear oil

free protective garments such as leather gloves, heavy shirt,

cuffless trousers, high shoes and a cap over your hair. Wear

ear plugs when welding out of position or in confined places.

Always wear safety glasses with side shields when in a

welding area.

6.g. Connect the work cable to the work as close to the welding

area as practical. Work cables connected to the building

framework or other locations away from the welding area

increase the possibility of the welding current passing

through lifting chains, crane cables or other alternate cir-

cuits. This can create fire hazards or overheat lifting chains

or cables until they fail.

6.h. Also see item 1.c.

6.I. Read and folllow NFPA 51B “ Standard for Fire Prevention

During Welding, Cutting and Other Hot Work”, available

from NFPA, 1 Batterymarch Park,PO box 9101, Quincy, Ma

022690-9101.

6.j. Do not use a welding power source for pipe thawing.

SAFETY

PRÉCAUTIONS DE SÛRETÉ

Pour votre propre protection lire et observer toutes les instruc-

tions et les précautions de sûreté specifiques qui parraissent

dans ce manuel aussi bien que les précautions de sûreté

générales suivantes:

Sûreté Pour Soudage A LʼArc

1. Protegez-vous contre la secousse électrique:

a. Les circuits à lʼélectrode et à la piéce sont sous tension

quand la machine à souder est en marche. Eviter toujours

tout contact entre les parties sous tension et la peau nue

ou les vétements mouillés. Porter des gants secs et sans

trous pour isoler les mains.

b. Faire trés attention de bien sʼisoler de la masse quand on

soude dans des endroits humides, ou sur un plancher

metallique ou des grilles metalliques, principalement dans

les positions assis ou couché pour lesquelles une

grande partie du corps peut être en contact avec la

masse.

c. Maintenir le porte-électrode, la pince de masse, le câble

de soudage et la machine à souder en bon et sûr état

defonctionnement.

d.Ne jamais plonger le porte-électrode dans lʼeau pour le

refroidir.

e. Ne jamais toucher simultanément les parties sous tension

des porte-électrodes connectés à deux machines à soud-

er parce que la tension entre les deux pinces peut être le

total de la tension à vide des deux machines.

f. Si on utilise la machine à souder comme une source de

courant pour soudage semi-automatique, ces precautions

pour le porte-électrode sʼapplicuent aussi au pistolet de

soudage.

2. Dans le cas de travail au dessus du niveau du sol, se pro-

téger contre les chutes dans le cas ou on recoit un choc. Ne

jamais enrouler le câble-électrode autour de nʼimporte quelle

partie du corps.

3. Un coup dʼarc peut être plus sévère quʼun coup de soliel,

donc:

a. Utiliser un bon masque avec un verre filtrant approprié

ainsi quʼun verre blanc afin de se protéger les yeux du

rayonnement de lʼarc et des projections quand on soude

ou quand on regarde lʼarc.

b. Porter des vêtements convenables afin de protéger la

peau de soudeur et des aides contre le rayonnement de

lʻarc.

c. Protéger lʼautre personnel travaillant à proximité au

soudage à lʼaide dʼécrans appropriés et non-inflamma-

bles.

4. Des gouttes de laitier en fusion sont émises de lʼarc de

soudage. Se protéger avec des vêtements de protection

libres de lʼhuile, tels que les gants en cuir, chemise épaisse,

pantalons sans revers, et chaussures montantes.

5. Toujours porter des lunettes de sécurité dans la zone de

soudage. Utiliser des lunettes avec écrans lateraux dans les

zones où lʼon pique le laitier.

6. Eloigner les matériaux inflammables ou les recouvrir afin de

prévenir tout risque dʼincendie dû aux étincelles.

7. Quand on ne soude pas, poser la pince à une endroit isolé de

la masse. Un court-circuit accidental peut provoquer un

échauffement et un risque dʼincendie.

8. Sʼassurer que la masse est connectée le plus prés possible

de la zone de travail quʼil est pratique de le faire. Si on place

la masse sur la charpente de la construction ou dʼautres

endroits éloignés de la zone de travail, on augmente le risque

de voir passer le courant de soudage par les chaines de lev-

age, câbles de grue, ou autres circuits. Cela peut provoquer

des risques dʼincendie ou dʼechauffement des chaines et des

câbles jusquʼà ce quʼils se rompent.

9. Assurer une ventilation suffisante dans la zone de soudage.

Ceci est particuliérement important pour le soudage de tôles

galvanisées plombées, ou cadmiées ou tout autre métal qui

produit des fumeés toxiques.

10. Ne pas souder en présence de vapeurs de chlore provenant

dʼopérations de dégraissage, nettoyage ou pistolage. La

chaleur ou les rayons de lʼarc peuvent réagir avec les

vapeurs du solvant pour produire du phosgéne (gas forte-

ment toxique) ou autres produits irritants.

11. Pour obtenir de plus amples renseignements sur la sûreté,

voir le code “Code for safety in welding and cutting” CSA

Standard W 117.2-1974.

PRÉCAUTIONS DE SÛRETÉ POUR

LES MACHINES À SOUDER À

TRANSFORMATEUR ET À

REDRESSEUR

1. Relier à la terre le chassis du poste conformement au code

de lʼélectricité et aux recommendations du fabricant. Le dis-

positif de montage ou la piece à souder doit être branché à

une bonne mise à la terre.

2. Autant que possible, Iʼinstallation et lʼentretien du poste

seront effectués par un électricien qualifié.

3. Avant de faires des travaux à lʼinterieur de poste, la

debrancher à lʼinterrupteur à la boite de fusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leur

place.

Mar. ʻ93

Thank You

for selecting a QUALITY product. We want you to take pride in

operating this product ••• as much pride as we have in bringing

this product to you!

Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it

handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.

The level of seriousness to be applied to each is explained below:

WARNING

This statement appears where the information must be followed exactly to avoid serious personal injury or loss of life.

This statement appears where the information must be followed to avoid minor personal injury or damage to this equipment.

CAUTION

Please Examine Carton and Equipment For Damage Immediately

When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims

for material damaged in shipment must be made by the purchaser against the transportation company at the

time the shipment is received.

Please record your equipment identification information below for future reference. This information can be

found on your machine nameplate.

Product _________________________________________________________________________________

Model Number ___________________________________________________________________________

Code Number or Date Code_________________________________________________________________

Serial Number____________________________________________________________________________

Date Purchased___________________________________________________________________________

Where Purchased_________________________________________________________________________

Whenever you request replacement parts or information on this equipment, always supply the information you

have recorded above. The code number is especially important when identifying the correct replacement parts.

On-Line Product Registration

- Register your machine with Lincoln Electric either via fax or over the Internet.

• For faxing: Complete the form on the back of the warranty statement included in the literature packet

accompanying this machine and fax the form per the instructions printed on it.

• For On-Line Registration: Go to our

WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then

“Product Registration”. Please complete the form and submit your registration.

CUSTOMER ASSISTANCE POLICY

The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equip-

ment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln

Electric for advice or information about their use of our products. We respond to our customers based on the best information in our posses-

sion at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such infor-

mation or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customerʼs particular purpose,

with respect to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating or

correcting any such information or advice once it has been given, nor does the provision of information or advice create, expand or alter any

warranty with respect to the sale of our products.

Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control

of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in

applying these types of fabrication methods and service requirements.

Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com

for any updated information.

TABLE OF CONTENTS

Page

Installation .......................................................................................................Section A

Technical Specifications ........................................................................................A-1

Safety Precautions ..........................................................................................A-2

Select Suitable Location..................................................................................A-2

Stacking ..........................................................................................................A-2

Tilting...............................................................................................................A-2

Input and Grounding Connections ..................................................................A-2

Power Cord Connection ..................................................................................A-2

Connection of Wire Feeders to EX350i ..........................................................A-2

Remote Control of Invertec .............................................................................A-3

Undercarriage Mountings................................................................................A-3

Parallel Operations..........................................................................................A-4

________________________________________________________________________

Operation .........................................................................................................Section B

Safety Precautions ................................................................................................B-1

General Description ..............................................................................................B-1

Duty Cycle .............................................................................................................B-1

Operational Features and Controls........................................................................B-1

Upper Control Panel.......................................................................................B-1, B-2

Hidden Middle Control Panel ...................................................................B-2 thru B-7

Lower Case Panel .................................................................................................B-8

Remote Control of the Output Control and Weld Terminals ..................................B-8

Auxiliary Power......................................................................................................B-9

Limitations..............................................................................................................B-9

Recommended Processes ....................................................................................B-9

_______________________________________________________________________

Accessories.....................................................................................................Section C

Options / Accessories............................................................................................C-1

Field Installed Options...........................................................................................C-1

Quick Disconnect Plugs.........................................................................................C-1

________________________________________________________________________

Maintenance ....................................................................................................Section D

Safety Precautions ................................................................................................D-1

APACITOR DISCHARGE PROCEDURE..........................................................................D-1

VISUAL INSPECTION...................................................................................................D-1

ROUTINE MAINTENANCE ............................................................................................D-1

ERIODIC MAINTENANCE ...........................................................................................D-1

________________________________________________________________________

Troubleshooting ..............................................................................................Section E

Safety Precautions.................................................................................................E-1

How to Use Troubleshooting Guide.......................................................................E-1

Troubleshooting Guide ...........................................................................E-2 Thru E-3

Fault Codes ...........................................................................................................E-4

Displays .................................................................................................................E-5

________________________________________________________________________

Connection , Wiring Diagrams and Dimension Prints .................................Section F

________________________________________________________________________

Parts List .....................................................................................................P-439 Series

________________________________________________________________________

EX350i

A-1

INSTALLATION

A-1

TECHNICAL SPECIFICATIONS -

RED-D-ARC EX350i

INPUT AC VOLTAGE & DC OUTPUT

* Overall Length Including Handle, 27.8” (706mm)

Voltage

200

208

230

380

400

415

460

575

200

208

230

380

400

415

460

575

Phases

300Amps @

32Volts(100%)

Not

Recommended

Not

Recommended

Not

Recommended

350Amps @

34Volts(60%)

Not

Recommended

Not

Recommended

Not

Recommended

Line Cord

AWG

---

Fuse size

---

125A

---

80A

70A

50A

80A

70A

50A

35A

EX350i INPUT CURRENT

OUTPUT CABLES, CONNECTIONS AND LIMITATIONS

Recommended Fuse Sizes Base On The U.S. National Electrical Code And Maximum Machine Outputs

Input 50/60 Hz Output Recommended

Note 1. Not rated is indicated by 4-xʼs in the box on the rating plate.

Note 2. When operating on these inputs, the line cord should be changed to an input conductor of 6 AWG or larger.

Select The output cable size based upon the following chart.

Cable sizes for Combined Length of Electrode and Work Cable (Copper) 75°C rated:

DUTY CYCLE

100%

60%

CURRENT

300

350

LENGTH UP TO 200FT.(61m)

1/0

200-250 FT. (61-76m)

1/0

2/0

Notes

Note 1

Note 2

Note 1

Note 2

Product

Name

EX350i

Output

Range

(Continuous)

AMPS

5-425

Open

Circuit

80 VDC

Ordering

Information

K1757-2

Input AC

Voltage

200

208-230/

380-400/

415-460/

575

1 & 3

PHASE

50/60Hz

Rated DC Output

Amps/Volt/

Duty Cycle

350/34/60%

300/32/100%

Height Width Depth

Weight

14.8”(373mm) 13.3”(338mm) 27.8” *(706mm*) 84.0 Lbs.(38.0 Kg)

PHYSICAL DIMENSIONS

TEMPERATURE RANGES

STORAGE TEMPERATURE RANGE

-40°C to +40°C

OPERATING TEMPERATURE RANGE

-20°C to +40°C

A-2

INSTALLATION

A-2

SELECT SUITABLE LOCATION

The EX350i will operate in harsh environments. Even

so, it is important that simple preventative measures

are followed in order to assure long life and reliable

operation.

• The machine must be located where there is free cir-

culation of clean air such that air movement in the

back, out the sides and bottom will not be restricted.

• Dirt and dust that can be drawn into the machine

should be kept to a minimum. Failure to observe

these precautions can result in excessive operating

temperatures and nuisance shutdown.

• Keep machine dry. Shelter from rain and snow. Do

not place on wet ground or in puddles.

• DO NOT MOUNT OVER COMBUSTIBLE SURFACES.

Where there is a combustible surface directly

under stationary or fixed electrical equipment,

that surface shall be covered with a steel plate at

least .06”(1.6mm) thick, which shall extend not

less than 5.90”(150mm) beyond the equipment on

all sides.

------------------------------------------------------------------------

STACKING

EX350i cannot

be stacked.

TILTING

Place the machine directly on a secure, level surface

or on a recommended undercarriage. The machine

may topple over if this procedure is not followed.

INPUT AND GROUNDING CONNECTIONS

• Only a qualified electrician should connect the

EX350i. Installation should be made in accordance

with the appropriate National Electrical Code, all

local codes and the information detailed below.

• When received directly from the factory, multiple

voltage machines are internally connected for

460VAC. If 460VAC is the desired input, then the

machine may be connected to the power system

without any setup required inside the machine.

• Initial 200VAC - 415VAC and 575VAC operation will

require an Input voltage panel setup.

SAFETY PRECAUTIONS

ELECTRIC SHOCK can kill.

• TURN THE INPUT POWER OFF AT

THE DISCONNECT SWITCH BEFORE

ATTEMPTING TO CONNECT OR DIS-

CONNECT INPUT POWER LINES, OUTPUT

CABLES, OR CONTROL CABLES.

• Only qualified personnel should perform this

installation.

• Connect the green/yellow lead of the power

cord to ground per National Electrical Code.

----------------------------------------------------------------------

WARNING

• Open the access panel on the rear of the machine.

• For 200 or 230: Position the large switch to 200-

230.

For higher voltages: Position the large switch to

380-575.

• Move the "A" lead to the appropriate terminal.

POWER CORD CONNECTION

A 25 ft. power cord is provided and wired into the

machine. Follow the power cord connection instruc-

tions.

• Incorrect connection may result in equipment

damage.

-----------------------------------------------------------------------

Single Phase Input

Connect green lead to ground per National Electrical

Code.

Connect black and white or brown leads to power.

Wrap red lead with tape to provide 600V insulation.

Three Phase Input

Connect green lead to ground per National Electric

Code.

Connect black, red and white leads to power.

CONNECTIONS OF WIRE FEEDERS TO EX350I

LN-25 Connection Instructions

-Not recommended for Pulse Welding with the

Advanced Process Kit ).

• Turn the EX350i power switch "off".

• Connect the electrode cable to the output terminal of

polarity required by electrode. Connect the work lead

to the other terminal.

• LN-25 with Remote Control options can be used with

the EX350i. The 14 pin (K444-2) remote can be con-

nected directly to the 14 pin amphenol. The 42 Volt

Remote Voltage and Output Control (K624-1) Kit can

be connected to the EX350i 24/42 VAC amphenol

using Remote Control Cable assembly K627- [ ]. LN-

25s with a K431-1 remote kit can be connected to

the 24/42 VAC amphenol using a K432 cable and a

K876 adapter. (See connection diagram S19899) to

connect it to one of the 14-pin amphenols. Or the

K432 cable could be modified with a K867 Universal

Adapter Plug (See connection diagram S19405) to

connect it to the 24/42 VAC 14-pin amphenol.

WARNING

REMOTE

OFF

AMPS

VOLTS

WELD TERMI

SELECT

LINCOLN

LECTRIC

INVERTEC V350-PRO

WARNING

AVISO DE

PRECAUCI

ATTENTION

orem

m d

t a

et c

nsectetuer adipisc

lit, ed d

mmy nibh euismod t

oreet

quam

Lor

lor

onse

tet

sci

it,

d d

num

my ni

smod

e mag

a ali

Lorem

psum

sit

met

consect

tuer

adi

sci

m n

eui

tin

cid

eet

e ma

quam

Lor

psum dolor sit

consect

tuer adi

iscin

elit, ed d

num

eui

lao

eet

agn

quam

Lor

psum dolor sit

met

consect

tuer

adi

isci

it,

d d

num

ibh

aor

uam

era

Lorem

psum

or sit

met

consect

tuer

adi

isci

nonu

cidu

aor

eet

agna

quam

Lore

m i

t c

ons

m n

eui

mod

dun

aoreet dolore

agna

Lorem

psum

or sit

met

consect

tuer

adi

isci

elit, ed

onum

nib

tinc

dunt

laoreet

ore ma

na al

quam era

Lor

ipsum dolor si

et consectetu

r adipis

ing

elit, ed

my n

ism

t ut

lore m

na ali

Lorem

psum

consecte

uer adi

iscing

m n

nib

gna

Lor

it,

d d

num

my n

oreet

aliquam

Lorem

psum

consecte

uer adi

scin

onum

mod

cid

eet

agna

quam

dolor

nsect

tuer

adi

isci

elit, ed d

num

eui

dun

aoree

agn

quam

rat

Lorem ipsum dolo

it a

t consectetue

adipis

lit, ed diam nonu

mmy

nibh

mod

tin

laoreet dolore m

na aliqu

m erat

ips

lor sit amet c

nsec

scing

nsect

non

ummy

nibh eui

mod

tin

eui

m i

um dolo

it a

sectet

ect

etu

elit,

iam nonu

nibh euismod

tin

am n

laoreet

olo

agna al

quam erat

m i

r sit

amet consec

adip

sci

sum

sci

am no

ummy n

smo

d tincidunt

mod

eet

t d

Lorem

psum

sit

nsec

tet

uer

adip

elit

onummy

eui

dun

aoree

dolore magna aliqu

m erat

Lore

sum

or s

r a

lit, ed d

mmy nibh eui

inc

laoreet dolore ma

na aliquam era

GREEN

RED

BLACK

WHITE or BROWN

EX350i

CAUTION

A-3

INSTALLATION

A-3

LN-7 Connection Instructions

• Turn the EX350i power switch “off”.

• Connect the K480 control cable from the LN-7 to

the EX350i 115 VAC control cable connector.The

control cable connector is located at the front of the

EX350i.

• Connect the electrode cable to the output terminal

of polarity required by electrode. Connect the work

lead to the other terminal

• Set the meter polarity switch on the front of the

EX350i to coincide with wire feeder polarity used.

The wire feeder will now display the welding volt-

age.

• If K480 is not available, see connection diagram

S19404 for modification of K291 or K404 LN-7 input

cable with K867 universal adapter plug.

LN-10 Connection Instructions

• Turn the EX350i power switch "off"

• Connect the K1505 control cable from the LN-10 to the

EX350i 24/42VAC 14-pin amphenol connector on the

front of the EX350i.

• Connect the electrode cable to the output terminal of

polarity required by the electrode. Connect the work lead

to the other terminal.

• Set the meter polarity switch on the front of the EX350i to

coincide with wire feeder polarity used.

• See the LN-10 manual for details on accessing Control

DIP Switch

LN-742 Connection Instructions

• Turn the

EX350i

power switch "off"

• Either a K591 or a K593 Input cable assembly is

required to connect the LN-742 to the

EX350i

• Connect the control cable from the LN-742 to the

24/42 VAC 14-pin wire feeder amphenol on the

front of the

EX350i

• Connect the electrode cable to the output terminal

of the polarity required by electrode. Connect the

work lead to the other terminal.

• Set the meter polarity switch on the front of the

EX350i

to coincide with wire feeder polarity used.

The wire feeder will now display the welding volt-

age.

• If a remote control is to be used with the LN-742,

use a K864 adapter to connect the feeder and a

K857 remote to the 14-pin wire feeder connector on

the front of the

EX350i

Cobramatic Connection Instructions

• Turn the

EX350i

power switch "off"

• Connect the control cable from the Cobramatic to

the 24/42 VAC 14-pin wire feeder amphenol on the

front of the

EX350i

• Connect the electrode cable to the output terminal

of the polarity required by electrode. Connect the

work lead to the other terminal.

• Set the meter polarity switch on the front of the

EX350i

to coincide with wire feeder polarity used.

• If a remote control is to be used with the

Cobramatic, or use a K864 adapter to connect the

cobramatic and a K857 remote to the 24/42VAC

14-pin wire feeder amphenol connector on the front

of the EX350i.

TIG Module K930-2

The TIG Module connects to the EX350i with a K936-

1 (9-14 pin) control cable. Connect the K936-1 to the

115VAC wire feeder amphenol on the front of the

EX350i.

General Instructions for Connection of Wire

Feeders to EX350i

Wire feeders other than LN-7 and LN-25 may be used

provided that the auxiliary power supply capacity of

the EX350i is not exceeded. K867 universal adapter

plug is required. See connection diagram S24985 on

page F-4.

REMOTE CONTROL OF INVERTEC

Remote Control K857, Hand Amptrol K963 and Foot

Amptrol K870.

UNDERCARRIAGE MOUNTINGS

5.50

10.00

MOUNTING HOLE LOCATIONS

1/4-20 NUT (4 PLACES)

NOTE: MOUNTING SCREWS CANNOT PROTRUDE MORE THAN 0.5 INCHES INSIDE THE MACHINE.

3.50

11.84

EX350i

A-4

INSTALLATION

A-4

EX350i

PARALLEL OPERATION

The EX350i are operable in parallel in CC mode. For

best results, the currents of each machine should be

reasonably well shared. As an example, with two

machines set up in parallel for a 400 amp procedure,

each machine should be set to deliver approximately

200 amps, not 300 amps from one and 100 amps

from the other. This will minimize nuisance shutdown

conditions. In general, more than two machines in

parallel will not be effective due to the voltage require-

ments of procedures in that power range.

To set machine outputs, start with output control pots

and arc control pots in identical positions. Use the

output control pots to balance the currents and main-

tain the desired voltage or current. The arc control

pots should be kept identical on the two machines.

B-1

OPERATION

EX350i

B-1

SAFETY PRECAUTIONS

ELECTRIC SHOCK can kill.

• Do not touch electrically live parts or

electrode with skin or wet clothing.

• Insulate yourself from work and

ground.

• Always wear dry insulating gloves.

------------------------------------------------------------------------

FUMES AND GASES can be danger-

ous.

• Keep your head out of fumes.

• Use ventilation or exhaust to remove

fumes from breathing zone.

------------------------------------------------------------------------

WELDING SPARKS can cause fire or

explosion.

• Keep flammable material away.

• Do not weld on closed containers.

------------------------------------------------------------------------

ARC RAYS can burn eyes and skin.

• Wear eye, ear and body

protection.

------------------------------------------------------------

See additional warning information at

front of this operatorʼs manual.

-----------------------------------------------------------

WARNING

GENERAL DESCRIPTION

The EX350i offers multi-process CV, CC, and DC

welding and is rated 350 amps, 34 volts at a 60% duty

cycle.

DUTY CYCLE

The EX350i is rated at 350 amps, 60% duty cycle

(based on a 10 minute cycle). It is also rated at 300

amps, 100% duty cycle.

OPERATIONAL FEATURES and CONTROLS:

UPPER CONTROL PANEL

1. AMPS Meter

• Prior to STICK or TIG operation (current flow), the

meter displays preset current value (either 2 amps

or +/- 3% (e.g. 3 amps on 100), whichever is

greater).

• Prior to CV operation, the meter displays four dash-

es indicating non-presettable AMPS.

• During welding, this meter displays actual average

amps.

• After welding, the meter holds the actual current

value for 5 seconds. Output adjustment while in the

"hold" period results in the "prior to operation" char-

acteristics stated above. The displays blink indicat-

ing that the machine is in the "Hold" period.

2. VOLT METER

• Prior to CV operation (current flow), the meter dis-

plays desired preset voltage value (+/- .5V).

• Prior to STICK or TIG operation, the meter displays

the Open Circuit Voltage of the Power Source or

four dashes if the output has not been turned on.

• During welding, this meter displays actual average

volts.

• After welding, the meter holds the actual voltage

value for 5 seconds. The displays blink indicating

that the machine is in the "Hold" period.

• Output adjustment while in the "hold" period results

in the "prior to operation" characteristics stated

above.

3. OUTPUT CONTROL

• Output control is conducted via a single turn poten-

tiometer.

• Adjustment is indicated by the meters as stated

above.

• When in TIG modes, this control sets the maximum

welding current. Full depression of a foot or hand

Amptrol results in the preset level of current.

4. WELD TERMINALS-REMOTE / ON

• Two status lights indicate the location of trigger con-

trol as determined by the "WELD TERMINALS"

push button.

• If trigger control is local "weld terminals on", the ON

display will be lit.

• If trigger control is remote "weld terminals remotely

controlled", the REMOTE display will be lit.

• The unit will power up in "pre-determined preferred"

trigger modes.

STICK = ON

CV = REMOTE

TIG = REMOTE if remote output controls are

attached to the machine.

TIG = 0N if remote output controls are not attached to

the machine.

For all versions, these trigger modes can be over-ridden

(switched) with the WELD TERMINALS push button. When

changed, the unit will power up in the configuration it was in

when it was last powered down.

B-2

OPERATION

B-2

THERMAL

• This status light indicates when the power source has

been driven into thermal overload. If the output terminals

were "ON", the "ON" light will blink indicating that the out-

put will be turned back on once the unit cools down to an

acceptable temperature level. If the unit was operating in

the "REMOTE" mode, the trigger will need to be opened

before or after the thermal has cleared and closed after

the machine has cooled down to an acceptable tempera-

ture to establish output.

CONTROL-REMOTE / LOCAL

• Two status lights indicate the location of output control as

pre-determined by the power sources auto-configure sys-

tem.

• The LOCAL display will be lit when control is at the power

source.

• The REMOTE display will be lit when a remote pot/control

is detected.

These Output Control configurations can be overridden

(switched) with the CONTROL push button. When

changed, the unit will power up in the configuration it was in

when it was last powered down.

Hidden Middle Control Panel – Process Set Up

Panel

7. WELD MODE SELECT -

The Mode Control button selects from the following

welding modes.

CC-STICK SOFT: The Stick Soft process features

continuous control ranging from 5 to 425 amps. This

mode was intended for most SMAW applications, and

Arc Gouging.

• Arc Gouging: Setting the output of the Stick Soft

mode to 425 amps will enable the arc-gouging

mode. The actual output current will depend on the

size of carbon used. The recommended maximum

size carbon is 5/16".

• The Hot Start control regulates the starting current

at arc initiation. Hot Start can be adjusted from min-

imum (0), with no additional current added at arc

start, to maximum (10), with double the preset cur-

rent or 425 amps (max of machine) added for the

first second after arc initiation.

• The Arc Control regulates the Arc Force to adjust

the short circuit current. The minimum setting (-10)

will produce a "soft" arc and will produce minimal

spatter. The maximum setting (+10) will produce a

"crisp" arc and will minimize electrode sticking.

CC-STICK CRISP: The Stick Crisp mode features

continuous control from 5 to 425 amps. This mode

was intended primarily for pipe welding applications.

• The Hot Start control regulates the starting current

at arc initiation. Hot Start can adjust starting current

up or down by 25% of the preset value. The recom-

mended setting for Hot Start is 5 where the initial

current is equal to the preset current.

• The Arc Control regulates the Arc Force to adjust

the short circuit current. The minimum setting (-10)

will produce a "soft" arc and will produce minimal

spatter. The maximum setting (+10) will produce a

"crisp" arc and will minimize electrode sticking.

EX350i

REMOTE

LOCAL

WELD TERMINALS

OUTPUT

CONTROL

SELECT

MPS

OLTS

SELECT

CC-STICK SOFT 7018

CC-STICK CRISP 6010

TIG GTAW

CV-WIRE

CV-FLUX CORED

HOT START

ARC CONTROL

-4

-2

-6

-10

SOFT

CRISP

+10

-8

FIGURE 1

B-3

OPERATION

B-3

TIG GTAW: The TIG mode features continuous con-

trol from 5 to 425 amps. The TIG mode can be run in

either the TIG touch start or high frequency (optional

equipment required) assisted start mode.

• The Hot Start control selects the starting mode

desired. A setting of less than 5, the TIG lift start

mode is selected. The OCV is controlled below 10v

and the short circuit "TIG touch" current is main-

tained at 25 amps independent of the preset cur-

rent.

When the tungsten is lifted, an arc is initiated and

the output is regulated at the preset value. Hot start

settings between 0 and 5 regulate the arc initiation

current. A setting of 5 results in the most positive

arc initiation. A setting of 0 reduces hot start.

• Hot Start settings between 5 and 10, select high

frequency assisted starting TIG mode. In this

range, the OCV of the machine is controlled

between 50 and 70 volts. If using the Lincoln K930-

1 TIG Module, set the Hot start to 10 for maximum

OCV.

• The Arc Control is not used in the TIG mode.

TIG SOLENOID OPTION

The Solenoid only operates when th V350 is in the

TIG mode. If the Weld Terminals are in “Remote” then

the solenoid will open when the arc start switch is

closed. The solenoid will close after the arc switch has

been opened and the post flow time expired.

If the Weld Terminals are turned “ON”, then the sole-

noid will open when the electrode is touch to the work.

The electrode needs to remain in contact with the

work to allow for gas coverage before attempting to

start the arc. The solenoid will close after the arc has

been broken and the post flow time expired.

CV-WIRE: The CV-WIRE mode features continuous

control from 10 to 40 volts. The mode was intended

for most GMAW, FCAW, and MCAW applications.

• The Hot Start control is not used in the CV-WIRE

mode.

• The Arc Control regulates pinch effect. At the mini-

mum setting (-10), minimizes pinch and results in a

soft arc. Low pinch settings are preferable for weld-

ing with gas mixes containing mostly inert gases. At

the maximum setting (+10), maximizes pinch effect

and results in a crisp arc. High pinch settings are

preferable for welding FCAW and GMAW with CO

CV-INNERSHIELD: The CV-INNERSHIELD mode

features continuous control from 10 to 45 volts. This

mode was designed for self-shielded flux cored wires

that require tight voltage control.

EX350i

• The Hot Start control is not used in the CV-FLUX

CORED mode.

• The Arc Control regulates pinch effect. At the mini-

mum setting (-10), minimizes pinch and results in a

soft arc. At the maximum setting (+10), maximizes

pinch effect and results in a crisp arc. Most self-

shielded wires work well at an Arc Control setting of 5.

B-4

OPERATION

B-4

7A. ADVANCED PROCESS PANEL

(See Figure 2)

To program Welding modes. Select knob is used to

Scroll through all Welding modes. The Memory button

is used to store and access Welding modes into loca-

tions M1 thru M8.

Modes:

In addition to the 5 welding modes described in SEC-

TION 7, the Advance Process Panel allows you to

select the Following additional modes.

• Constant Power mode

In the Power Mode;

The work point will be in the Volts window. The

Amp window will have CP displayed indicating

Constant Power. Once current starts flowing and

during the 5 second “Hold” feature the displays will

show Volts and Amps respectively.

• Gouge

Air Carbon Arc Cutting (CAC-A) is a physical means

of removing base metal or weld metal by using a

carbon electrode, an electric arc and compressed

air.

EX350i

• Pulsed Modes

In Pulse Modes;

The work point will be in the Amps window and

should be set close to the wire feed speed of the

wire feeder in inches per minute. The Volts window

will have SPd displayed indicating Wire Feed

Speed. Once current starts flowing and during the 5

second “Hold” feature the displays will show amps

and volts.

Pulse Mode features that are displayed while

selecting a Welding pulse mode are listed below;

Steel - .030, .035, .045, .052 – Argon Blends

Stainless Steel - .030, .035, .045 – Argon Blends &

Helium/Argon Blends

Aluminum - .035, 3/64, 1/16 – 4043 & 5356

Metal Core - .045, .052 – Argon Blends

Nickel - .035, .045 – Argon/Helium blends

MEMORY

MEMORY BUTTON

(M1 THRU M8)

OUTPUT KNOBOUTPUT KNOB

SELECT BUTTON

(HOT START OR ARC CONTR

OL)(HOT START OR ARC CONTROL)

ADJUST KNOB

(0 THRU 10-HOT START)

(-10 THRU 0 AND

0 THRU +10-ARC CONTROL)

SELECT KNOB

(

SCOLLS WELDING PROCESSES)

(SCOLLS WELDING PROCESSES)

SELECT

ADJUST

SELECT

ADVANCE PROCESS PANEL VERSION

REMOTE

LOCAL

WELD TERMINALS

OUTPUT

CONTROL

SELECT

MPS

OLTS

FIGURE 2

B-5

OPERATION

B-5

EX350i

CONTROLS: (See Figure 2)

The MEMORY button and SELECT knob are used

together to select a welding process and store it in

memory (M1 thru M8). The SELECT knob scrolls

through the, welding process modes and memory M1

thru M8. The MEMORY button stores the welding

process in memory.

• SELECT button" (The right button) selects between

the "Hot Start" or "Arc Control". The < will indicate

the active feature shown below.

Right Digital Window

"Hot Start" (-10 to 0 +10)

"Arc Control" (0 to 10) <

• The ADJUST knob adjusts the desired settings for

the Hot Start or Arc Control feature that is active.

WELDING PROCESS MODES AVAILABLE

Stick SMAW, TIG GTAW

Gouge CAG, CV MIG GMAW

CV Flux Core, Pulse MIG

ELECTRODE MATERIAL

Steel, Metal Core, Stainless, Aluminum, Nickel

EXAMPLE OF SAVING WELDING MODES TO

MEMORY

The following example is how to select Pulse MIG

using .035 steel and store it into memory.

1. Turn the Select knob until welding process is dis-

played.

RIGHT WINDOW LEFT WINDOW

Pulse MIG Argon Blends

Steel .035

2. Wait two seconds and the right window will display

Arc Control on the second line on the right side.

Pulse MIG Argon Blends

Steel .035 Arc Cntrl ### <

3. SPd is displayed in the upper right Volts window.

The left Amps window matches the desired wire

feed speed that is set on the wire feeder. Adjust the

Output knob until desired number is displayed.

4. Start welding. If the arc length is too short turn the

Output knob up. If the arc length is too long turn

the Output knob down.

The Arc Control which is displayed in the right digital

window can be used to fine-tune the arc length and

characteristics.

5. After all adjustments have been made press and

hold the Memory button until the display changes.

The right and the left window will display a memory

position, lets say M1(or turn knob to select memory

of your choice. To store in M1 push the Memory

button again to save the Pulse Mig mode to memo-

ry M1.

6. The display in the digital windows read as follows:

M1 Pulse MIG Argon Blends

Steel .035 Arc Cntrl 1.2

7. To save a second welding mode to a memory posi-

tion of your choice, turn the Select knob until the

desired welding process mode is displayed in right

digital window. Then follow steps 1 thru 6.

8. Adjust the output control to the correct wire feed

setting and the EX350i is ready to weld again.

(Note: The wire feed speed setting is not stored in

memory and will need to be reset.)

9. Adjust the Arc Control and note that the M1 goes

away indicating that the EX350i settings no longer

match what is stored in memory. Going back to the

original settings will not bring the M1 back. You will

need to push the Memory button to recall the origi-

nal settings in M1.

Note: After all memoryʼs M1 thru M8 are used and the

welder needs to store another welding process, a new

welding process will overwrite what was originally in

the memory and will read,

Save to MEM

M1 Overwrite

M1 which stored Pulse Mig is Overwritten with the

new welding process.

B-6

OPERATION

B-6

WELD MODE DETAILS:

EX350i

Mode Range Comments

Stick Soft 5 - 425 amps The stick soft mode is the best selection for general stick

applications.

Arc Control = Arc Force

Hot Start = Initial hot start current (min = start a match set amps, Max. =

greatest hot start current) During hot start, arc force is set at

high and is fast response.

For gouging applications: Turn current up to 425 amps.

Stick Crisp 5 - 425 amps The stick crisp mode features an aggressive arc force routine well suit-

ed for Exx10, Exx11 series electrodes.

Arc Control = Arc Force

Hot Start = Initial hot start current (Mid range = welding current and will

vary up and down with knob control.) During hot start, arc

force is set at high and is fast response.

For gouging applications: Turn current up to 425 amps.

GTAW (Tig mode) 5 - 425 amps The tig mode produces a soft, steady constant current waveform for

either touch start or high frequency assisted start DC GTAW applica-

tions.

Hot Start = Min to Mid range = Touch start with low OCV

Mid to Max range = High frequency assisted starting with adjustable

OCV up to 70 volts.

GMAW - CV 10 - 45 volts The GMAW - CV mode is the best selection for general MIG welding,

Metal core, and gas shielded applications.

Arc Control = Pinch (Min = min pinch, softest arc),

(Max = max pinch, crispest arc)

FCAW-SS 10 - 45 volts The FCAW-SS mode is designed for Self Shielded Innershield products

that require tight voltage control. For example; the NR 203 series or NR

207)

Arc Control = Pinch (Min = min pinch, softest arc),

(Max = max pinch, crispest arc, )

ADVANCED PULSE PANEL WELDING PROGRAMS

Gouging 60 - 425 amps The gouging mode is a low power version of other Lincoln welding

equipment gouging programs, for example a Power Wave 455.

GMAW - Power 1 - 18 (No Units) The GMAW - Power mode features good stable short arc performance

when welding small diameter (.025 and .030 steel & stainless) wires at

low procedures. This mode also performs well welding aluminum in the

spray mode.

This mode does not allow preset voltage. In the short arc GMAW mode,

the set KW will not equal the actual Volts * Amps. The set power is reg-

ulated only when an arc is present. During shorting, the output is

allowed to increase to clear the short.

B-7

OPERATION

B-7

PULSE PROGRAMS:

EX350i

MODE IMP*

.030 Steel 65 - 1200

.035 Steel 55 - 800

.045 Steel 50 - 700

.052 Steel 75 - 550

.045 Metal Core 50 - 650

.052 Metal Core 50 - 500

.030 Stainless Ar Blends 85 - 770

.030 Stainless He Ar CO2 110 - 770

.035 Stainless Ar Blends 65 - 770

.035 Stainless He Ar CO2 75 - 770

.045 Stainless Ar Blends 50 - 600

.045 Stainless He Ar CO2 50 - 600

.035 Aluminum 4043 100 - 700

.035 Aluminum 5356 115 - 740

3/64 Aluminum 4043 80 - 550

3/64 Aluminum 5356 85 - 700

1/16 Aluminum 4043 75 - 325

1/16 Aluminum 5356 75 - 450

.035 Nickel Alloys

(Non Adaptive)

80 - 700

.045 Nickel Alloys

(Non Adaptive)

75 - 550

COMMENTS

The EX350i pulse programs are non-synergic and allow indepen-

dent control of the wire feed speed and the arc length. The Output

Control Knob on the EX350i, adjusts an "SPD" value. Similar to

trim, the "SPD" value indicates the relative arc length setting. The

value of "SPD" is meant to be a starting point at which to set the

arc length relative to the wire feed speed. Depending on the appli-

cation, the "SPD" value can be adjusted to obtain the desired arc

length.

The "SPD" value displayed on the EX350i may not match the

actual wire feed speed!

The operation of the Arc Control knob on the EX350i is similar to

the Power Wave series. As Arc Control is increased, the frequency

is increased and the background reduced. Decreasing Arc Control

will reduce frequency and increase background current. Arc

Control acts to fine tune the arc plasma to the specific application.

Preferred gas selections:

Steel Argon Blends = Argon with CO2 additions from 2 to 20

% or Oxygen additions from 2 to 5%.

Stainless Argon Blends = Argon with Oxygen additions up to 2%

Stainless Argon Blends = Argon with Oxygen additions up to 2%.

Stainless He Ar CO2 = ~ 90% Helium, 7 1/2 % Argon 2 1/2

CO2

Aluminum 100% Argon

The Nickel Alloy pulse programs are non adaptive. The operator

sets the output control knob to deliver the correct arc length at

desired wire feed speed and stick out. While welding, the operator

manipulates the stick out to maintain the correct arc length. This

method of operation produces very stable arc performance consid-

ering the nature of nickel alloys.

Preferred gas: Argon/Helium Blends = for the best results add

helium to the argon base from 0-25%.

.035 4043 (4x Pulse on Pulse) 120 - 600

3/64 4043 (4x Pulse on Pulse) 85 - 400

.035 5356 (5x Pulse on Pulse) 130 - 700

3/64 5356 (5x Pulse on Pulse) 100 - 550

Arc Control = Pulse on Pulse frequency. For faster travel

speed welds, the arc control should be increased.

For larger puddle, slower travel speeds, the arc control

should be decreased.

PULSE ON PULSE

*IPM (INCHES PER MINUTE)

B-8

OPERATION

B-8

EX350i

LN-10/DH-10 Wire Feeder Compatibility Note:

The LN-10 and DH-10 feeders can be used to pulse

weld and in the power mode with the panel. The dis-

plays on the LN-10 & DH-10 do not show the wire

feed speed or power.

8. HOT START and ARC CONTROL features have

different functions depending on the welding Mode

that is active. Each feature is described under the

welding mode heading. (See Item 7 or 7.A for speci-

fied Mode Operations) (See Figure 1 or 2)

LOWER CASE PANEL (See Figure 1)

The output studs, line switch and remote connector

are located on the lower case front.

9. Both STUDS contain "Twist-Mate" connector

inserts.

• The Negative stud is configured to accept the

pass through gas system.

10. The ON-OFF switch is a 3-phase circuit breaker

rated at 100 amps per leg.

11. The METER POLARITY switch is located above

the output connectors. The switch provides a work

connection for wire feeder voltmeters. Place the

switch in the position of the electrode polarity indi-

cated by the decal. The switch does not change

the welding polarity.

12. 3-PIN AMPENOL for remote control.

REMOTE CONTROL of the OUTPUT CONTROL and

WELD TERMINALS

The EX350i has auto sensing of remote output con-

trols.If after connecting or removing a remote, the

EX350i is not configured the way you would like the

local or remote control settings can be changed by

pushing the OUTPUT CONTROL or WELD TERMI-

NAL button. (A user cannot select between the 3 and

14 pin amphenols.)

CV modes

• The remote will default to the 14-pin amphenol

remote if a remote is connected to either of the 14-

pin amphenols and the 3-pin amphenol. Note: Only

one of the 14-pin amphenols can have a remote

control connected at a time. If no remote is connect-

ed to either of the 14-pin amphenols then the

remote will default to the 3-pin amphenol if a remote

is connected to it.

• If a remote control is connected or is not connect-

ed to any of the amphenols the WELD TERMINAL

control will default to REMOTE.

TIG mode

• The remote will default to the 3-pin amphenol if a

remote control is connected to the 3-pin amphenol

and one of the 14-pin amphenols. If a remote is not

connected to the 3-pin amphenol then the remote

will default to the 14-pin amphenols if a remote is

connected to one of the 14-pin amphenols.

• If a remote control is connected to any of the

amphenols the WELD TERMINAL control will

default to REMOTE. If there are not any remote

control devices attached the WELD TERMINAL con-

trol will default to ON.

CC-Stick modes

• The remote will default to only the 3-pin amphenol if

a remote is connected to it.

• The WELD TERMINAL control will default to ON

with or without a remote connected.

Types of Remote OUTPUT CONTROL

• The EX350iʼs Output Control can be controlled by

either a potentiometer connected between 77 & 75

with the wiper connected to 76 or a 0V to 10V DC

supply connected between 76 & 75. (76 needs to

be positive)

• 14-Pin Amphenol lead 75 is pin G, lead 76 is pin F

and lead 77 is pin E.

• 3-pin Amphenol lead 75 is pin A, lead 76 is pin B

and lead 77 is pin C.

Potentiometer Control

• The total resistance should be between 2000 ohms

(2K) and 10,000 ohms (10K)

• The machine output will be at minimum when lead

76 (wiper) is at the end of the potentiometer that is

connected to 75. The machineʼs output will increase

as the wiper of the potentiometer is moved to the

end that is connected to 77. (Note: In TIG mode,

moving the lead 76 (wiper) to lead 77 would pro-

duce the current that has been set by the EX350iʼs

front panel Output Control.)

Voltage Control

• The supply should be an isolated supply. (Not refer-

enced to earth ground, any auxiliary power from the

EX350i or the welding output) The supply should be

capable of supplying at least 20mA.

• 0 volts supplied to 76 will set the EX350i to mini-

mum output for the mode that has been selected

while 10 volts supplied to 76 will set the EX350i to

the maximum output for the mode. (Note: In TIG

mode, 10 volts supplied to lead 76 would produce

the current that has been set by the EX350iʼs front

panel Output Control.)

Types of Remote WELD TERMINAL Control

• The EX350iʼs Weld Terminals can be controlled

from each of the 14 pin amphenol connectors. The

circuit has a nominal OCV of 15VDC and requires a

dry contact closure (less than 100 ohms) to activate

the output of the EX350i.

• 14 Pin Amphenols the Weld Terminals are controlled

from pins C (lead 2) and pin D (lead 4). Pin C is posi-

tive.

B-9

OPERATION

B-9

EX350i

AUXILIARY POWER

• 115VAC, 42VAC and 24VAC power is available

from the two 14-pin amphenols on the rear of the

unit. These supplies are intended to supply power

for auxiliary equipment like wire feeders and the TIG

Module.

• 115VAC supply is rated at 2 amps and is protected

by a 2.5 amp breaker located by the amphenol.

• 42 VAC supply is rated at 5.5 amps and is protected

by a 10 amp breaker located by the amphenol.

• 24 VAC supply is rated at 5.5 amps and is protected

by a 10 amp breaker located by the amphenol.

LIMITATIONS

• The EX350i is not recommended for processes

other than those listed.

• The EX350i can only be used with the recommend-

ed equipment and options.

RECOMMENDED PROCESSES

Properly equipped, the EX350i supports GMAW,

FCAW, SMAW, GMAW-P, GTAW and CAC-A

processes for a variety of materials, including mild

steel, stainless steel, cored wires, and aluminum.

La page charge ...

Lincoln Electric Red-D-Arc EX350i Mode d'emploi

Marque: Lincoln Electric

Modèle: Red-D-Arc EX350i

Catégorie: Système de soudage

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Lincoln Electric Red-D-Arc EX350i Operating instructions

Lincoln Electric Red-D-Arc EX350i Mode d'emploi

Lincoln Electric Red-D-Arc EX350i Mode d'emploi

dans d''autres langues

Documents connexes