GE GDT635HGJWW Manuel utilisateur

Marque: GE

Modèle: GDT635HGJWW

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

Dishwashers

Owner’s Manual

49-55097-1 07-15 GE

Safety Instructions ............. 2-3

Operating Instructions

Care and Cleaning ............... 12-13

Getting Started ..................... 4-5

Loading and Place Settings ........ 8-10

Loading the silverware baskets ...... 11

Using the Dishwasher ...............6-7

Troubleshooting Tips ......... 14-16

Consumer Support

Consumer Support ....................18

Warranty ............................17

GEAppliances.com

Write the model and serial

numbers here:

Model # _________________

Serial # __________________

You can find them on the tub wall

just inside the door.

FRONT CONTROL MODELS TOP CONTROL MODELS

Lave-vaisselle

Lavaplatos

Manuel d’utilisation

Manual del propietario

La section française commence à la page 19

La sección en español empieza en la página 39

Dishwashers

ADT521 Series

GDF500-620 Series

GDT535-635 Series

Printed in the United States

Includes GE

and GE Artistry

™

Series products

IMPORTANT SAFETY INFORMATION

5($'$//,16758&7,216%()25(86,1*³

SAVE THESE INSTRUCTIONS

For your safety, the information in this manual must be followed to minimize the risk

of fire, explosion, electric shock, and to prevent property damage, personal injury, or

death.

WARNING!

WATER HEATER SAFETY

WARNING!

Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two or more weeks.

HYDROGEN GAS IS EXPLOSIVE.

If the hot water has not been used for two or more weeks, prevent the possibility of damage or injury by turning on all hot

water faucets and allowing them to run for several minutes. Do this before using any electrical appliance connected to

the hot water system. This simple procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable,

do not smoke, use an open flame, or use the appliance during this process.

 Use this appliance only for its intended purpose as

described in this Owner’s Manual.

 Use only detergents or wetting agents

recommended for use in a dishwasher

and keep them out of reach of children.

Using a detergent that is not specifically

designed for dishwashers will cause the

dishwasher to fill with suds.



Locate sharp items so that they are not likely to damage the

door seal.

 Load sharp knives with the handles up to reduce the risk of

cut-type injuries.

 Do not wash plastic items unless marked dishwasher safe

or the equivalent. For plastic items not so marked, check the

manufacturer’s recommendations.

 Do not touch the heating element during or immediately

after use.

 Do not operate your dishwasher unless all enclosure

panels are properly in place.

 Do not tamper with controls.



Do not abuse, sit on or stand on the door or dish rack of the

dishwasher.

 To reduce the risk of injury, do not allow children to play with,

on or inside this appliance at any time.

 Do not store or use combustible materials including gasoline

or other flammable liquids or vapors in the vicinity of this or any

other appliance.

 Small parts, such as rack clips and filter retaining posts, can

be a choke hazard to small children if removed from the

dishwasher. Keep out of reach of small children.

WARNING!

When using your dishwasher, follow basic precautions, including the following:

PROPER INSTALLATION AND MAINTENANCE

This dishwasher must be properly installed and located in accordance with the Installation Instructions before it is used. If

you did not receive an Installation Instructions sheet with your dishwasher, you can receive one by visiting our Website at

GEAppliances.com. In Canada, visit www.GEAppliances.ca.

 Connect the dishwasher/appliance to a grounded metal,

permanent wiring system; or run an equipment-grounding

conductor with the circuit conductors and connect to the

equipment-grounding terminal or lead of the appliance.



Improper connection of the equipment-grounding conductor

can result in a risk of electric shock. Check with a qualified

electrician or service representative if you are in doubt

whether the appliance is properly grounded.

 Dispose of discarded appliances and shipping or packing

material properly.

 Do not attempt to repair or replace any part of your

dishwasher unless it is specifically recommended in this

manual. All other servicing should be referred to a qualified

technician.

 Use only cord kit WX09X70910 or hard-wire to building

electrical. Failure to follow this instruction, could result in risk of

fire and personal injury.

 To minimize the possibility of electric shock, disconnect this

appliance from the power supply before attempting any

maintenance.

NOTE: Turning the dishwasher off does not disconnect the

appliance from the power supply. We recommend having

a qualified technician service your appliance.

WARNING!

IMPORTANT SAFETY INFORMATION

5($'$//,16758&7,216%()25(86,1*³

SAVE THESE INSTRUCTIONS

GEAppliances.com

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE DISHWASHER

Junked or abandoned dishwashers are dangerous…even if they will sit for “just a few days.” If you

are getting rid of your dishwasher, please follow the instructions below to help prevent accidents.

 Do not allow children to play with, on, or inside this or any discarded appliance.

 Take off the door of the washing compartment or remove the latch by removing the two screws

from the latch receiver inside the tub (as shown).

WARNING!

Two screws

CAUTION:

To prevent minor injury and property damage

 During or after wash cycle, contents may be hot to the

touch. Use care before handling.

 Close supervision is necessary if this appliance is used by

or near children. Do not allow children to play around the

dishwasher when closing the door, closing the upper rack,

or while vertically adjusting the upper rack due to the

possibility of small fingers being pinched.

 Non-Dishware Items: Do not wash items such as

electronic air cleaner filters, furnace filters and paint

brushes in your dishwasher. Damage to the dishwasher

and discoloration or staining of the dishwasher may

result.

 Load light-weight, plastic items so they do not become

GLVORGJHGDQGGURSWRWKHERWWRPRIWKHGLVKZDVKHU³

they might come into contact with the heating element

and be damaged.

CAUTION:

 This appliance must be supplied with 120V, 60 Hz, and

connected to an individual, properly grounded branch

circuit, protected by a 15 or 20 amp circuit breaker or

time-delay fuse.

 If the electric supply provided does not meet the above

specifications, it is recommended that a licensed

electrician install an approved outlet.

 Your dishwasher circuit should not be used for any other

appliance while the dishwasher is in operation as the

dishwasher requires the full capacity of the circuit.

ELECTRICAL REQUIREMENTS

 If your dishwasher is connected to a wall switch,

ensure that the switch is on prior to use.

 If you choose to turn the wall switch off between

wash cycles, allow 5-10 seconds after turning the

switch on before touching Start to allow the control

to initialize.

 Use only powder, Cascade

All-in-1 ActionPacs™, liquid

detergents or rinse agents recommended for use in a

dishwasher and keep them out of the reach of children.

Cascade

All-in-1 ActionPacs™ Automatic Dishwashing

Detergent, and Cascade

Rinse Aid™ rinse agents have

been approved for use in all GE dishwashers.

NOTICE

Getting started!

Load Dishwasher

For best dishwashing results, follow the rack loading guidelines found in the Loading the dishwasher racks section. No pre-rinsing of

normal food soil is required. Scrape off hard soils, including bones, toothpicks, skins, and seeds. Remove leafy vegetables, meat trimmings,

and excessive amounts of grease or oil. Remove acidic food soils that can discolor stainless steel.

Add Detergent

Add needed amount of detergent to the detergent dispenser. Use a detergent such as Cascade Complete All-in-1 ActionPacs™. See Detergent

Dispenser in the Using the dishwasher section.

Add Rinse Agent

Add Rinse Agent to the rinse agent dispenser. See

Use a Rinse Agent such as Cascade

Rinse Aid

™ in the Using the dishwasher section.

Select Cycle

Press the Select Cycle pad for the desired wash cycle. The light next to the Select Cycle pad will be on to indicate which wash cycle has been

selected.

The cycle may be selected with the door in the open position. The cycle will not start until after the door is closed and Start selected. Cycle time

will vary based on soil in loads and cycle selected. Other options may add time to your cycle

AutoSense

This cycle automatically senses the soil level and adjusts the wash cycle accordingly.

(on some models)

Heavy This cycle is meant for heavily soiled dishes, cookware, pots, or pans with dried-on or baked-on soils.

Everyday dishes are safe to be used in this cycle.

Normal

This cycle is meant for daily, regular, or typical use to completely wash a full load of normally soiled dishes and is

designed to conserve both water and energy. NOTE: Normal was used to rate the energy efficiency of this dishwasher.

Light

This cycle is for light to medium soiled dishes. It is safe for china and crystal but because of its lower final rinse

temperature, will provide limited dry performance.

Rinse For rinsing partial loads that will be washed later. Do not use detergent. Detergent is not dispensed during the

(on some models) rinse cycle.

Select Options

The light by the selected pad will be ON to indicate which Option has been selected.

Bottle Jets

This option increases the time that the bottle jets are on and may add up to 23 minutes to the cycle

(on some models)

time. Use this to wash difficult to clean, dishwasher safe baby bottles, sport bottles, tall coffee cups, etc. See use

recommendations in the Loading the dishwasher section.

Wash Temp

This option increases the temperature to help clean heavily soiled dishes and may increase the overall cycle time.

Boost Option may be turned On or Off during the wash cycle. Wash Temp also increases the final rinse temperature which can

(on some models) improve dry performance .

Wash Temp This option raises the water temperature in the final rinse to sanitize your dishware and improve dry

Sani performance. The cycle length will vary depending on the temperature of your inlet water.

(on some models) NOTE: This option is monitored for sanitization requirements. If the cycle is interrupted during or after the main

wash portion or if the incoming water temperature is so low that adequate water heating cannot be achieved,

the sanitizing conditions may not be met. In these cases, the Sanitized light will not illuminate at the end of the

cycle. Utilizing this option will modify the cycle to meet the requirements of Section 6, NSF 184 for soil removal

and sanitization efficacy.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

Heated Dry Shuts off the heat drying option. Dishes air dry naturally and energy is saved. Open the dishwasher door to

Off

speed drying.

Heated Dry Turns on the heater for faster drying. This cycle may extend the time to your wash cycle up to 64 minutes. This

option is not available with the Rinse cycle.

Features and appearance will vary throughout this manual

GEAppliances.com

Select Options (Continued)

Steam For use with heavily soiled and/or dried-on, baked-on soils. This option MUST be selected PRIOR to

(Prewash) starting the cycle. The Steam option adds approximately 30 minutes to the cycle time. This option is

(on some models)

available with Heavy, AutoSense, and Normal cycles.

Wash Selecting either the Upper or Lower Wash Zones will target dishwashing of just one rack. This will

Zones shorten the cycle time and conserve energy. This option can be used when there is only half a

(on some models)

load of dishes.

Delay Delays the start of a wash cycle up to 12 hours, depending on model. Press Delay Hours, to select

Hours the number of hours, then press Start one time to begin countdown. The cycle will start once allotted time

(on some models) has expired.

Control You can lock the controls to prevent selections from being made. You can also lock the controls

Lock after you have started a cycle to prevent cycle changes.

For example, children cannot accidentally

start the dishwasher by pressing pads with this option selected.

To LOCK the dishwasher control, depending on the model, press and hold the Heated Dry pad for 3 seconds or

press and hold the Steam and Wash Temp pads at the same time for 3 seconds. The Control Lock light will turn

on to indicate the control is locked.

To UNLOCK the dishwasher control, depending on the model, press and hold the Heated Dry pad for 3 second

or press and hold the Steam and Wash Temp pads at the same time for 3 seconds. The Control Lock light

will turn off to indicate the control is unlocked.

Start Dishwasher

Start Door can be open to select the desired options. Press the Start pad and close the door within 10 seconds

to start the cycle or begin the Delay Hours countdown. The wash cycle will begin shortly after closing

the door. If the door is open, the illuminated lights will turn off if a pad is not pressed within two minutes.

To activate the display, close and open the door or press any pad.

Interrupt To interrupt or pause a dish cycle, slowly open the door. Opening the door will cause the wash cycle to

or Pause pause. The dishwasher will beep every minute to remind you to close the door. To restart or resume

the cycle, press Start, and close the door.

Cancel To cancel a wash cycle, press and hold the Start pad for 3 seconds and close door. The dishwasher will drain,

emit a beep sound, and the wash cycle light will turn OFF.

Cycle Completion

Sanitized Displayed at the end of the cycle when Wash Temp Sani (Sanitize) has been selected and the dishwasher has met the

requirements for sanitization. See Wash Temp Sani, for complete option description. Opening the door or pressing any

key while the door is closed will turn off the light.

Clean Displayed when a wash cycle is complete. The light stays ON as a reminder that the dishes are clean.

Opening

the door or pressing any key while the door is closed will turn the light off.

Door Wake

To turn this option ON/OFF, press and hold the START and WASH TEMP pads for 5 seconds, close the door and wait

Up Mode 3 minutes for the dishwasher to go into sleep mode. In the OFF mode, the control display, control sounds,

(on some models)

and interior lights will not respond to the door opening/closing. This mode can be used when observing certain

religious holidays such as the Sabbath. To activate the control and interior lights, press any pad.

Using the dishwasher.

Check the Water Temperature

Use a Rinse Agent such as Cascade

Rinse Aid™

Rinse agents, such as Cascade

Rinse Aid™ are designed for great drying action and protect against spots

and film build-up on your dishes, glasses, flatware, cookware, and plastic.

Filling the Dispenser

The rinse agent dispenser holds 3.5 oz. (100 ml) of rinse agent. Under normal

conditions, this will last approximately one month.

Make sure the dishwasher door is fully open.

Open the RINSE AID dispenser door.

Slowly add rinse agent until the fill cup is full. May need to pause several times to

allow rinse aid to settle.

Clean up any spilled rinse agent with a damp cloth.

Close the RINSE AID dispenser door.

Rinse Aid Setting

The amount of rinse agent released into the final wash can be adjusted. The

factory setting is at the midpoint. If hard water spots appear on dishes, try a

higher setting. If you see foam in the dishwasher, move the indicator to a lower

setting.

To adjust the setting

Open the RINSE AID dispenser door;

then turn the adjuster clockwise to

increase the amount of rinse agent,

counterclockwise to reduce the amount

of rinse agent.

The entering water should be at least 120°F (49°C) and

not more than 150°F (66°C) for effective cleaning and to

prevent dish damage. Check the water temperature with a

candy or meat thermometer. Turn on the hot water faucet

nearest the dishwasher, place the thermometer in a glass

and let the water run continuously into the glass until the

temperature stops rising.

Rinse

agent

adjuster

Indicator

window

Clockwise to reduce

water drops and

hard water spots

Counterclockwise

to reduce foaming

GEAppliances.com

The detergent dispenser is located in the center of

the dishwasher door. It has two compartments. The

main wash compartment is found inside the detergent

dispenser. To open, press the blue button on the side of

the dispenser. The pre-wash compartment is on the lid of

the detergent dispenser. Use the pre-wash compartment

only when your water is extremely hard or when you have

a heavy soiled load.

NOTE: Do not block detergent dispenser with large or tall

utensils.

You may use tablet, powder, liquid or gel automatic

dishwasher detergent. Make sure you use only detergents

specifically labeled for use in automatic dishwashers. Never

use liquid hand dish detergent in an automatic dishwasher.

Sudsing and poor wash performance will result with the use of

improper detergents.

Detergents should be stored in a dry location and in their

original container to prevent loss of effectiveness. Place

detergent in the cup just prior to starting the dishwasher and

then close the cover. The cover will open during the wash

cycle.

Filling the Detergent Dispenser

GE recommends using detergent in tablet or packet form.

Independent testing has shown this form of detergent is very

effective in the dishwasher.

Cascade

Platinum Pacs are

an example of this type of detergent.

Simply put a tablet

or packet into the main wash compartment and slide to

close the detergent cup cover. Please notice that the tablet or

packet must be placed in the main wash compartment of the

detergent cup. If the tablet or packet is tossed in the bottom of

the dishwasher, the detergent will be flushed down the drain

in a very short period of time and will thus be wasted. Wash

performance will be very poor as a result.

If you choose to use detergent in powder, liquid or gel form,

the amount of detergent you use will be determined by the

hardness of your water, the temperature of your water, and

the food soil load inside the dishwasher. Contact your water

company to get information about the hardness of the water

in your area. Water hardness is measured in grains per gallon.

Use this information and the table above to determine the

amount of detergent to use. You may purchase a hard water

test strip from GE. Call 1-877-959-8688 and ask for part

number WD01X10295. In Canada, call 1-800-661-1616

Using too much detergent with very soft and/or very

hot water may cause a condition called etching on your

glassware. Etching is a permanent cloudiness in your

glassware. This condition is irreversible. However, using too

little detergent will cause poor wash performance.

Use the table as a starting point and then adjust the amount

of detergent you use. Use just enough to get good wash

performance. Using just the right amount of detergent will

provide great wash performance without wasting detergent

or etching of glassware.

DO NOT USE HAND DISH DETERGENT

NOTE: Using a detergent that is not specifically designed

for dishwashers will cause the dishwasher to fill with suds.

During operation, these suds will spill out of the dishwasher

vents, covering the kitchen floor and making the floor wet.

Because so many detergent containers look alike, store the

dishwasher detergent in a separate space from all other

cleaners. Show anyone who may use the dishwasher the

correct detergent and where it is stored.

While there will be no lasting damage to the dishwasher, your

dishes will not get clean using a dishwashing detergent that is

not formulated to work with automatic dishwashers.

Detergent Dispenser

Number of

Grains/Gal.

Detergent Cups to Fill

Less than 4 Fill cup to 1/3 full

4 to 8 Fill cup to 2/3 full

8 to 12 Fill cup completely full

Greater than 12

Fill both main wash cup and pre

wash cup

Pre-Wash

Main

Wash

Rinse Agent

Detergent

Dispenser

Push/Slide

to Close

Loading and place settings.

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware

baskets may vary from your model.

Upper Rack

The upper rack is primarily for glasses, cups, and

saucers. However, other items such as pots, pans,

and plates may be placed in the upper rack. This is

also a secure place for dishwasher-safe plastic items.

The upper rack can be used for odd sized utensils.

Sauce pans, mixing bowls, and other similarly shaped

items should be placed face down for best wash

performance. Ensure small plastic items are secure

so that they cannot fall into the heater at the bottom

of the dishwasher, potentially damaging the item.

On some models, the upper rack may be adjusted

to accommodate larger items. To adjust the upper

rack, fully extend the upper rack and remove the two

plastic end caps on the front of the rails. Remove the

upper rack. Select the set of rollers on the side of the

rack that provides the desired height, and reinstall

the upper rack by guiding the rack rails between the

appropriate set of rollers. With the rack reinstalled,

replace the two plastic end caps, ensuring the snap

is properly engaged. Failure to properly engage

the end caps may result in the rack falling from the

dishwasher.

To add flexibility in loading, the utility

shelf (on some models) may be

placed in the up or down position.

The shelf may also be used to

secure

stemware such as wine

glasses. Because these

stemware items come

in various sizes, slowly push

the rack in to ensure

the items do not bump into the edges of the

dishwasher, which may cause damage

to the

items.

It is important to ensure that items do not protrude

through the bottom of the rack or silverware basket

(on some models) where they will block the rotation

of the middle spray arm. This could result in noise

during operation and/or poor wash performance.

Check to make sure that no items will

block rotation of the wash arms.

End

Cap

Rollers

Rail

Place the slots in the

utility shelf clips over

the vertical

rack wires

and

push down to

attach

utility shelf onto

second wire of rack

Sports bottle held in

place over a Bottle Jets

clip

Baby bottle held in place

under a Bottle Jets clip

The Bottle Jets system (on some models) is the

ideal location to position tall cups, sports bottles,

and baby bottles. The Bottle Jets clips hold

bottles with small openings in place so water jets

are directed inside to clean hard to reach areas. Clips

can be installed or removed by simply slipping the

clip opening over the top of the nozzle.

Clip

Nozzle

Bottle Jets

Upper Rack - 10 Place Settings

GDF510-610, GDT535-545, GDT625

& ADT521

Upper Rack - 12 Place Settings

GDF510-610, GDT535-545, GDT625

& ADT521

Upper Rack - 8 Place Settings

GDF510-610, GDT535-545, GDT625

& ADT521

GEAppliances.com

Upper Rack - 8 Place Settings

GDF620, GDT635

Upper Rack - 10 Place Settings

GDF620, GDT635

Upper Rack - 12 Place Settings

GDF620, GDT635

Lower Rack

The lower rack is best used for plates, saucers and

cookware items. Large items, such as broiler pans

and baking racks should go along the sides of the

rack. If necessary, oversized glasses and mugs can

be placed in the lower rack to maximize loading

flexibility. Plates, saucers and similar items should be

placed between the tines in the direction that allows

the item to remain secure in the rack.

It is important to ensure that items do not protrude

through the bottom of the rack or the silverware

basket where they will block the rotation of the lower

spray arm. This could result in noise during operation

and/or poor wash performance.

Lower Rack - 10 Place Settings

GDF510 & GDT535

Lower Rack - 8 Place Settings

GDF510 & GDT535

Lower Rack - 10 Place Settings

GDF520, GDF610, ADT521, GDT545

& GDT625

Lower Rack - 12 Place Settings

GDF520, GDF610, ADT521, GDT545

& GDT625

Lower Rack - 8 Place Settings

GDF520, GDF610, ADT521, GDT545

& GDT625

Lower

Rack - 12 Place Settings

GDF620, GDT635

Lower

Rack - 8 Place Settings

GDF620, GDT635

Lower

Rack - 10 Place Settings

GDF620, GDT635

Loading and place settings (cont.).

Lower Rack - 12 Place Settings

GDF510 & GDT535

Silverware Basket

Place flatware in the removable silverware and

accessory baskets (on some models). Sharp objects,

such as forks and knives, may be placed with the

handles facing up, in order to protect your hands.

For the best wash performance, place other items

such as spoons with the handles facing down. Avoid

allowing items to nest together, which may keep

them from being properly washed. When loading,

distribute items evenly in the basket.

The silverware and accessory baskets (on some

models) may also be used for small items, such as

measuring spoons, baby bottle nipples, plastic lids,

or corn cob holders. The silverware basket covers (on

some models) can be closed to contain small items.

The door mounted silverware basket (on some

models) may be positioned either on the door by

securing the basket to the door using the two

mounting bosses, or to the rack by securing the

basket to the rack using the wire loop on the front of

the lower rack to engage the tabs on the rear of the

basket.

The accessory basket (on some models) may be

positioned by placing the hooks on the back of the

basket over the top wire on the sides of the lower

rack.

Secure the basket to the rack using the wire loop on

the front of the upper and lower racks to engage the

tabs on the rear of the basket.

Do not load large or tall utensils where they may

block the detergent dispenser or become trapped

between the door and the gasket when the door is

closed.

Loading the silverware baskets…

Silverware

Basket

Silverware

Basket

Wire Loops

Mounting

Bosses

Silverware Basket - 8 Place Settings

GDF520, GDF610, GDT545, GDT625 & ADT521

Silverware Basket - 8 Place Settings

GDT635

Silverware Basket - 10 Place Settings

GDT635

Silverware Basket - 12 Place Settings

GDT635

Silverware Basket - 10 Place Settings

GDF520, GDF610, GDT545, GDT625 & ADT521

Silverware Basket - 12 Place Settings

GDF520, GDF610, GDT545, GDT625 & ADT521

Silverware Basket - 8 Place Settings

GDF510 & GDT535

Silverware Basket - 10 Place Settings

GDF510 & GDT535

Silverware Basket - 12 Place Settings

GDF510 & GDT535

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware

baskets may vary from your model.

Care and cleaning.

Cleaning the Control Panel

To clean the control panel, use a lightly

dampened cloth. Then dry thoroughly.

Stainless Steel Inner Door

The stainless steel used to make the dishwasher

inner door provides the highest reliability

available in a GE dishwasher.

If the dishwasher inner door should be

scratched or dented during normal use, it will

not rust or corrode. These surface blemishes

will not affect its function or durability.

Cleaning the Dishwasher Interior

Cleaning the Exterior Door Panel

Before cleaning the front panel, make sure you

know what type of panel you have. Refer to the

last two letters of your model number. You can

locate your model number on the left-hand tub

wall just inside the door. If your model number

ends with BB, CC, WW, SA or ES then you have

a painted door panel. If your model number

ends with SS, then you have a Stainless Steel

door panel. If your model number ends with II,

then you have an Integrated door panel.

Follow the instructions below for cleaning the

door panel for your specific model.

Painted Door Panel (model numbers ending in

BB–black, CC–bisque, WW–white, SA-silver or

ES-slate)

Use a clean, soft, lightly dampened cloth, then

dry thoroughly. You may also use a good

appliance wax or polish.

Do not use scouring pads or powered

cleaners because these products can scratch

the finish.

Stainless Steel Door Panel (model numbers

ending in SS)

For cleaning rust and tarnish, cleaners with

oxalic acid such as Bar Keepers Friend Soft

Cleanser™ will remove rust, tarnish and small

blemishes. Use only a liquid cleanser free

of grit and rub in the direction of the brush

lines with a damp soft sponge. Do not use

appliance wax or polish on the stainless steel.

For other blemishes and marks, use Stainless

Steel Magic or a similar product using a clean

soft cloth. Do not use appliance wax, polish,

bleach or products containing chlorine on

Stainless Steel. You can order Stainless Steel

Magic™ # WX10X29 through

GE Parts by

calling 877.959.8688. In Canada, call 1-800-

661-1616.

Integrated Door Panel (model numbers ending

in II)

This is a custom installed door panel, and you

will need to refer to the cabinet manufacturers

recommendations for proper cleaning.

* Lemi Shine® is a registered trademark of Envirocon Technologies, Inc.

To clean and de-odorize your dishwasher,

use citric acid or Lemi Shine®*, a detergent

additive. Lemi Shine will break up mineral

deposits, and remove hard water film and

stains. You can order citric acid #WD35X151

through GE Parts by calling 877-959-8688 or

visiting GEApplianceparts.com. In Canada,

call 1-800-661-1616. You can purchase

Lemi Shine at your local grocery store or by

calling GE at the numbers above and ask for

WX10X10019.

GEAppliances.com

An air gap protects your dishwasher against water

backing up into it if a drain clogs. The air gap is not

a part of the dishwasher. It is not covered by your

warranty. Not all plumbing codes require air gaps,

so you may not have one.

The air gap is easy to clean.

Turn off the dishwasher and lift off the air gap

cover.

Remove the plastic cap under the cover and

clean with a toothpick.

Replace the cap and cover when the air gap is

clean.

Does Your Dishwasher Have an Air Gap?

If your dishwasher is left in an unheated place

during the winter, ask a service technician to:

Turn off electrical power to the dishwasher.

Remove fuses or trip circuit breaker.

Turn off the water supply and disconnect the

water inlet line from the water valve.

Drain water from the water inlet line and

water valve. (Use a pan to catch the water.)

Reconnect the water inlet line to the water

valve.

Protect Against Freezing

Check the air gap any

time your dishwasher

isn’t draining well.

Air gap

Inspect and clean the filters periodically. This should be done every other month or so depending on usage. If there is a

decrease in wash performance or dishes feel gritty, this is also an indication the filters need to be cleaned.

Cleaning the Filters

Ultra-Fine Filter

To clean the Ultra-Fine Filter, remove the bottom

rack. Twist counterclockwise and remove the

Ultra-Fine Filter. Rinse filter with warm soapy

water and use a sponge to carefully remove any

stubborn particles. Scrubbing with scouring pads

or brushes can damage the filter. Once cleaned,

replace the Ultra-Fine Filter, and twist clockwise to

lock in place.

Fine Filter

To clean the Fine Filter (mesh plate), remove the

bottom rack. Remove the Ultra-Fine Filter.

Twist counterclockwise each of the two retaining

posts located toward the back bottom of the

tub, and remove the Fine Filter. Rinse filter with

warm soapy water. Scouring pads or brushes

can scratch the filter surface but a soft brush or

sponge may be needed to remove stubborn soils

or calcium deposits caused by hard water. Once

cleaned, replace the Fine Filter, the Ultra-Fine

Filter, and twist clockwise the two retaining posts

into place.

WARNING! The retaining posts

can be a choke hazard for small children if

removed from the dishwasher. Keep out of

reach of children.

Fine Filter

Spray Arm

Retaining Posts

Ultra-Fine

Filter

Before you call for service…

Troubleshooting Tips

Save time and money! Review the charts on the following pages, or visit GEAppliances.com.

In Canada visit www.GEAppliances.ca. You may not need to call for service.

Problem

Possible Causes What To Do

Start Status The door was opened or the • Press the Start pad once to start the dishwasher. Press the

indicator light flashing cycle was interrupted. Start pad a second time when the dishwasher is running only if you

wish to cancel the cycle.

Dishwasher BEEPS This is a reminder that your • Press Start and close the door.

once every minute dishwasher door has been left

(on some models) open during operation. It will

continue beeping until you press

Start and close the door.

Beeping at the end This is normal. The dishwasher • To turn off the double beep indicator (or re-activate it if it was previously

of the cycle will beep twice at the end of the turned off), press the Heated Dry pad 5 times within 3 seconds.

(on some models) cycle. A triple beep will sound to indicate the end-of-cycle beep option

has been turned on or off.

Dishes and flatware Ultra fine or fine filter is clogged • See the Care and cleaning section.

not clean Low inlet water temperature • Make sure inlet water temperature is correct (see the Using the dishwasher

section). Turn on the hot water faucet nearest the dishwasher, let run until

the water temperature stops rising. Then start the dishwasher and turn

off the faucet. This ensures the entering water is hot. Select Wash Temp Boost if

available.

Water pressure is temporarily low • Turn on a faucet. Is water coming out more slowly than usual? If so, wait

until pressure is normal before using your dishwasher.

Air gap or disposer is clogged • Clean the air gap or flush the disposer.

Improper rack loading • Make sure large dishware does not block the detergent dispenser or the

wash arms. See the Loading the dishwasher racks section.

• When large utensils are placed in the silverware basket, do not mount the basket

on the door (on some models). Instead, mount basket on the lower rack.

Poor performing detergent • Use a highly rated detergent such as Cascade Complete

All-in-1 ActionPacs™.

Spots and filming Extremely hard water • Use rinse agents such as Cascade

Rinse Aid™ to remove spots

on glasses and and prevent new film buildup.

flatware

• If water is extremely hard, a softener may be required.

Low inlet water temperature • Make sure water temperature is at least 120°F.

Overloading or improper • Load dishwasher as shown in the Loading Place Settings section.

loading of the dishwasher

Old or damp powder detergent • Make sure detergent is fresh.

Rinse agent dispenser empty • Refill with rinse agent such as Cascade

Rinse Aid™.

Too little or low performing • Make sure you use the proper amount of highly rated detergent.

detergent

Problem Possible Causes What To Do

Cloudiness on Combination of soft water and • This is called etching and is permanent. To prevent this from happening,

glassware too much detergent use less detergent if you have soft water. Wash glassware in the shortest

cycle that will get it clean.

Low performing phosphate • See A white film on glassware, dishware and the interior in this

free detergent Troubleshooting section.

Water temperature entering the • This could be etching. Lower the water heater temperature.

dishwasher exceeds 150°F (66°C)

Suds in the tub Correct detergent • Use only automatic dishwasher detergents to avoid sudsing. Cascade

wasn’t used Automatic Dishwashing Detergents have been approved for use in all

GE dishwashers.

• To remove suds from the tub, open the dishwasher and let suds dissipate.

Pump out water by pressing Start and close the door. Wait 30 seconds.

Open the door, press and hold Start for 3 seconds, and close the door.

Repeat if necessary.

Rinse agent was spilled • Always wipe up rinse agent spills immediately.

Detergent left in Dishes or utensils are blocking • Reposition the dishes, so the water from the lower spray arm can flush

dispenser cups the detergent cup the detergent cup. See the Loading the dishwasher racks section.

• Reposition the tall utensils or heavy silverware that may be keeping the

dispenser cup door from opening. See the Loading the silverware basket

section.

Black or gray Aluminum utensils have • Remove marks with a mild, abrasive cleaner.

marks on dishes rubbed against dishes

Dishes don’t dry Low inlet water temperature • Make sure inlet water temperature is at least 120°F.

• Select Heated Dry.

• Use Wash Temp Boost option.

• Select a higher cycle, such as Wash

Temp Sani (

Sanitize) or Heavy.

Rinse agent dispenser is empty • Check the rinse agent dispenser and fill as required.

Cycle selection • If using Light Cycle which uses lower water temperature and thus limited dry

performance, switch to a different cycle.

Cycle completion • Allow cycles to fully complete. See Long Cycle Times in this Troubleshooting

section

Control panel responded Door may not be completely • Make sure the door is firmly closed.

to inputs but dishwasher closed

never filled with water

Water valve may be turned off • Make sure water valve (usually located under the sink) is turned on.

Stained tub interior Some tomato-based foods can • Use of the Steam cycle (on some models) after adding the dish to the load

cause reddish stains can decrease the level of staining.

Tea or coffee stains • Remove the stain by hand, using a solution of 1/2 cup bleach and

3 cups warm water. NOTE: Do not use bleach on stainless steel

tub or inner door.

CAUTION!

Before cleaning interior, wait at least 20 minutes after a cycle for the

heating elements to cool down. Failure to do so can result in burns.

An overall yellow or brown film can

• A special filter in the water supply line is the only way to correct

be caused by iron deposits in water

this problem. Contact a water softener company.

:KLWHILOPRQLQVLGHVXUIDFH³ • GE recommends Cascade

Rinse Aid™ to help prevent hard water

hard water minerals mineral deposits from forming.

• Run dishwasher with citric acid to remove mineral deposits. Citric acid

(Part number: WD35X151) can be ordered through GE Parts. See back

cover for ordering information.

Dishwasher won’t run Fuse is blown or circuit breaker • Replace fuse or reset circuit breaker. Remove any other appliances from

is tripped the circuit.

Power is turned off • In some installations, the power to the dishwasher is provided through a

wall switch, often located next to the disposer switch. Make sure it is on.

Control panel is locked • Unlock control panel. See the Getting started section.

GEAppliances.com

Problem Possible Causes What To Do

Control panel lights Time too long between • Each pad must be touched within 30 seconds of the others.

go off when you’re touching of selected pads To relight, touch any pad again or open the door and

setting controls unlock (top control).

Water standing in Air gap is clogged • Clean the air gap. See the Care and cleaning section.

the bottom of the tub

Water won’t pump Drain is clogged • If you have an air gap, clean it. See the Care and cleaning section.

out of the tub

• If the dishwasher drains into a disposer, run disposer clear.

• Check to see if your kitchen sink is draining well. If not, you

may need a plumber.

Steam This is normal • Warm, moist air comes through the vent during drying and when

water is being pumped out. This is necessary for drying.

Sanitized light does The door was opened and the • Do not interrupt the cycle by opening the door during the wash cycle.

not illuminate at the cycle was interrupted during

end of the cycle final rinse

The incoming water • Raise the water heater temperature to between 120°F and 150°F.

temperature was too low

Noise Normal operating sounds: • These are all normal. No action is required.

Detergent cup opening

Water entering dishwasher

The motor stops and starts at

various times during the cycle

Spray arms start and stop at

various times

Drain pump sounds during

pump out

Drain pump starts and stops

several times during each drain

Rattling dishes when the spray • Make sure dishes are properly loaded. See the Loading the

arm rotates dishwasher racks section. Ensure dishes do not extend below rack, so they

do not contact the spray arm as it rotates.

Rattling silverware against door • Tall utensils may be placed in the upper rack to avoid bumping against

during wash inner door during wash cycle.

A white film on This problem caused by • To remove the white film, run your dishes through a dishwasher cycle with

glassware, dishware phosphate-free dishwasher citric acid. Use a WD35X151 citric acid kit found online.

and the interior detergent Pour the citric acid in the detergent cup and close the cover. Place the filmed

but otherwise clean glassware and dishware in the dishwasher. Leave

silverware and other metal items out of the dishwasher. Turn the dishwasher

on and let it run through a complete cycle without detergent. The glassware,

dishware, and dishwasher should come out film free. Alternatively,

a vinegar rinse may be used. Pour 1 cup of vinegar into dishwasher just after

the detergent cup opens and let the dishwasher complete its cycle.

This may be repeated several times a year as needed

The use of a rinse agent such as Cascade

Rinse Aid™ may help minimize

a repeat build up of film. Also, the use of a highly rated detergent such as

Cascade Complete

All-in-1 ActionPacs™ will help prevent film build-up.

Long cycle times Dishwasher washes by • Longer cycles are normal. For best wash and dry performance, let cycle

alternating mid and lower complete.

spray arms

Soil level • The turbidity sensor senses how much soil is on the dishes. Heavy soiled dish

loads will add more time to the cycle. This is normal function. For best wash

and dry performance, allow cycle to complete.

Before you call for service…

What Is Not Covered (for customers in Canada):

 Service trips to your home to teach you how to use

the product.

 Improper installation.

If you have an installation problem, contact your dealer

or installer. You

are responsible for providing adequate

electrical, exhausting and other connecting facilities.

 Failure of the product if it is abused, misused, or used for

other than the intended purpose or used commercially.

 Replacement of house fuses or resetting of circuit breakers.

 Damage to the product caused by accident, fire, floods

or acts of God.

 Damage caused after delivery.

For The Period Of: GE Will Replace:

One Year Any part of the dishwasher which fails due to a defect in materials or workmanship. During

From the date of the this limited one-year warranty, GE will also provide, free of charge, all labor and in-home

original purchase service to replace the defective part.

What GE Will Not Cover (for customers in the United States):

 Service trips to your home to teach you how to use

the product.

 Improper installation, delivery or maintenance.

 Failure of the product if it is abused, misused, or used for

other than the intended purpose or used commercially.

 Replacement of house fuses or resetting of circuit breakers.

 Product not accessible to provide required service.

 Damage to the product caused by accident, fire, floods

or acts of God.

 Incidental or consequential damage caused by possible

defects with this appliance.

 Cleaning or servicing of the air gap device in the drain line.

 Damage caused after delivery, including damage from

items dropped on the door.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA.

If the product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge

or you may be required to bring the product to an Authorized GE Service location for service. Proof of original purchase date is needed

to obtain service under the warranty. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal

rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or

state consumer affairs office or your state’s Attorney General.

Warrantor: General Electric Company. Louisville, KY 40225

This warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada for home use within

Canada. In home warranty service will be provided in areas where it is available and deemed reasonable by Mabe to provide.

Staple your receipt here.

Proof of the original purchase

date is needed to obtain service

under the warranty.

Dishwasher Warranty. GEAppliances.com

All warranty service provided by our Factory Service Centers, or an

authorized Customer Care

technician. To schedule service, visit us on-line

at GEAppliances.com, or call 800.GE.CARES (800.432.2737) in the United

States. In Canada, call 1.800.561.3344. Please have serial number and

model number available when calling for service.

WARRANTOR IS NOT RESPONSIBLE FOR CONSE QUEN TIAL DAMAGES.

(;&/86,212),03/,(':$55$17,(6³<RXUVROHDQGH[FOXVLYHUHPHG\LVSURGXFWUHSDLUDVSURYLGHGLQWKLV/LPLWHG

Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose,

are limited to one year or the shortest period allowed by law.

(;&/86,212),03/,(':$55$17,(6³<RXUVROHDQGH[FOXVLYHUHPHG\LVSURGXFWUHSDLUDVSURYLGHGLQWKLV/LPLWHG

Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose,

are limited to one year or the shortest period allowed by law.

Warrantor: MC Commercial, Burlington, ON, L7R 5B6

Servicing your appliance may require the use of the onboard data port for diagnostics. This gives a GE

Factory Service technician the ability to quickly diagnose any issues with your appliance and helps GE

improve its products by providing GE with information on your appliance. If you do not want your appliance

data to be sent to GE, please advise your technician NOT to submit the data to GE at the time of service.

Consumer Support.

GE Appliances Website

Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,

any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,

order parts or even schedule service on-line.

Schedule Service

Expert GE repair service is only one step away from your door. Get on-line and schedule your service at your

convenience any day of the year! Or call 800.GE.CARES (800.432.2737) during normal business hours.

In Canada, call 800.561.3344

Real Life Design Studio In the US: GEAppliances.com

*(VXSSRUWVWKH8QLYHUVDO'HVLJQFRQFHSW³SURGXFWVVHUYLFHVDQGHQYLURQPHQWVWKDWFDQEHXVHGE\SHRSOHRI

all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and mental abilities

and impairments. For details of GE’s Universal Design applications, including kitchen design ideas for people with

disabilities, check out our Website today. For the hearing impaired, please call 800.TDD.GEAC (800.833.4322).

In Canada, please write to: Director, Consumer Relations, MC Commercial

1 Factory Lane, Suite 310

Moncton, N.B. E1C 9M3

Extended Warranties

Purchase a GE extended warranty and learn about special discounts that are available while your warranty is still

in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours. GE Consumer

Home Services will still be there after your warranty expires. In Canada, please consult your local listings for your

extended warranty provider.

Parts and Accessories In the US: GEApplianceParts.com

Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes

(VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or by phone at

877.959.8688 during normal business hours.

Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally

should be referred to qualified service personnel. Caution must be exercised, since improper servicing may

cause unsafe operation.

In Canada, call 800.661.1616

If you are not satisfied with the service you receive from GE, contact us on our Website with all the details including

your phone number, or write to: General Manager, Customer Relations

GE Appliances, Appliance Park

Louisville, KY 40225

In Canada, please write to: Director, Consumer Relations, MC Commercial

1 Factory Lane, Suite 310

Moncton, N.B. E1C 9M3

5HJLVWHU\RXUQHZDSSOLDQFHRQOLQH³DW\RXUFRQYHQLHQFHTimely product registration will allow for enhanced

communication and prompt service under the terms of your warranty, should the need arise. You may also

mail in the pre-printed registration card included in the packing material.

In the US: GEAppliances.com

In Canada: GEAppliances.ca

In the US: GEAppliances.com

In Canada: GEAppliances.ca

In the US: GEAppliances.com

In Canada: GEAppliances.ca

In the US: GEAppliances.com

In Canada: GEAppliances.ca

In the US: GEAppliances.com

In Canada: GEAppliances.ca

CONSIGNES DE SÉCURITÉ .. 20-21

DIRECTIVES DE FONCTIONNEMENT

Chargement la vaisselle

.....................................................................26-28

Chargement de panier à couverts ... 29

Entretien et nettoyage .................... 30-31

Tableau de commande

et réglages ........................................... 22–23

Utilisation du lave-vaisselle ..........24–25

AVANT D’APPELER UN RÉPARATEUR

.....................................................................32-35

SERVICE À LA CLIENTÈLE

Garantie ........................................................ 37

Service à la clientèle ...................................38

Inscrivez ci-dessous les numéros

de modèle et de série :

N° de modèle _______________

N° de série __________________

Ils se trouvent sur la paroi de la cuve,

à l’intérieur de la porte.

Modèles avec commandes à l'avant

Modèles avec commandes sur le dessus

CONSIGNES DE SÉCURITÉ IMPORTANTES

VEUILLEZ LIRE TOUTES LES CONSIGNES AVANT D’UTILISER

/·$33$5(,/³&216(59(=&(6',5(&7,9(6

Dans certaines conditions, il peut se former de l’hydrogène dans un chauffe-eau qui n’a pas été utilisé pendant deux

semaines ou plus. L’HYDROGÈNE EST UN GAZ EXPLOSIF.

Si vous n’avez pas utilisé votre chauffe-eau pendant deux semaines ou plus, ouvrez tous les robinets d’eau chaude

et laissez couler l’eau pendant plusieurs minutes afin de réduire les risques de dommages matériels ou de blessures.

Prenez cette précaution avant même d’utiliser un électroménager raccordé au chauffe-eau pour éliminer l’hydrogène qui

pourrait s’y être accumuléé. Puisqu’il s’agit d’un gaz inflammable, ne fumez pas ou n’utilisez pas une flamme nue ou un

électroménager au cours de ce processus.

 N’utilisez cet appareil que pour l’usage pour lequel il a été

conçu, comme expliqué dans le présent manuel.

 Utilisez uniquement un détergent ou

un agent mouillant recommandés pour

utilisation dans un lave-vaisselle et

tenez-les à l’écart des enfants. L’utilisation

d’un détergent non conçu pour les lave-

vaisselles peut provoquer la formation de mousse.

 Placez les articles coupants de manière à ce qu’ils

n’endommagent pas le joint d’étanchéité de la porte.

 Placez dans le panie r à couverts les couteaux tranchants le

manche vers le haut afin de réduire les risques de coupures.

 Ne lavez pas les articles en plastique à moins qu’ils

ne portent la mention « Lavable au lave-vaisselle » ou

l’équivalent. Si certains articles en plastique ne portent

pas cette mention, reportez-vous aux recommandations du

fabricant.

 Ne touchez pas à l’élément chauffant pendant ou

immédiatement après le fonctionnement de l’appareil.



Ne faite pas fonctionner le lave-vaisselle si tous les panneaux

de la carrosserie n’ont pas été correctement réinstallés.

 Ne modifiez pas le fonctionnement des commandes.



Abstenez-vous de vous asseoir, de vous accrocher ou de vous

tenir sur la porte ou

le panier du lave-vaisselle, ou d’en faire un

emploi abusif de toute autre manière.

 Pour réduire le risque de blessure, ne laissez pas les enfants

jouer avec l’électroménager, grimper dessus ou s’y introduire.



Ne rangez ni n’utilisez des matières combustibles, y compris de

l’essence ou d’autres liquides ou vapeurs inflammables, à proximité

de cet appareil ou de tout autre.

 Les petites pièces, telles qu’attaches de panier et tiges de

retenue de filtre, représentent un risque d’étouffement

pour les jeunes enfants si elles sont retirées du lave-

vaisselle. Gardez-les à l’écart des jeunes enfants.

Ce lave-vaisselle doit être correctement installé, en conformité avec les directives d’installation fournies, avant d’être utilisé.

Si vous n’avez pas reçu les directives d’installation avec votre appareil, vous pouvez vous les procurer en visitant notre site

Web à l’adresse www.electromenagersge.ca.

 Cet appareil doit être relié à un système de câblage électrique

permanent en métal, mis à la terre. Sinon, un fil de mise à la

terre pour appareillage doit être installé et raccordé à la borne

ou au fil de mise à la terre de l’appareil.

 Un raccordement incorrect du fil de mise à la terre peut

présenter un risque d’électrocution. Consultez un électricien

ou un technicien qualifié si vous n’êtes pas certain que

l’appareil est correctement mis à la terre.

 Veuillez vous débarrasser de la façon appropriée de vos

vieux électroménagers et des matériaux d’emballage ou

d’expédition.

 Ne tentez pas de réparer ou de remplacer une pièce

quelconque de votre

lave-vaisselle, à moins que cela ne soit

spécifiquement recommandé dans le présent manuel. Confiez

toutes les autres réparations à un technicien qualifié.

 Utilisez uniquement un nécessaire de cordon électrique

WX09X70910 ou câblez directement sur le circuit électrique

du domicile. L’omission d’observer cette instruction peut

causer un risque d’incendie ou de blessure.



Pour réduire au minimum les risques d’électrocution, débranchez

l’appareil de sa source d’alimentation avant d’en effectuer l’entretien.

REMARQUE : Le fait d’arrêter le lave-vaisselle ne coupe l’alimentation

électrique de l’appareil. Nous vous recommandons de confier la

réparation de votre électroménager à un technicien qualifié.

Pour votre sécurité, veuillez suivre les directives données dans le présent

manuel afin de réduire au minimum les risques d’incendie, d’explosion et de

chocs électriques et prévenir tout dommage et blessure grave ou mortelle.

AVERTISSEMENT!

SÉCURITÉ DU CHAUFFE-EAU

AVERTISSEMENT!

INSTALLATION ET ENTRETIEN APPROPRIÉS

AVERTISSEMENT!

Lors du fonctionnement de votre lave-vaisselle, prenez les précautions

de base, notamment les suivantes :

La page charge ...

GE GDT635HGJWW Manuel utilisateur

Marque: GE

Modèle: GDT635HGJWW

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: GE GDT635HGJWW User manual
español: GE GDT635HGJWW Manual de usuario

Documents connexes

Autres documents

GE Appliances GDT530PSPSS Le manuel du propriétaire