LG WT1001CW Le manuel du propriétaire

OWNER’S MANUAL

WASHING MACHINE

www.lg.com

Before beginning installation, read these instructions carefully. This will simplify

installation and ensure that the washer is installed correctly and safely.

Leave these instructions near the washer after installation for future reference.

ENGLISH

FRANÇAIS

WT1001CW

P/No.: MFL68019706

2

PRODUCT FEATURES

TABLE OF CONTENTS

3 IMPORTANT SAFETY INSTRUCTIONS

3 Basic Safety Precautions

4 Grounding Requirements

5 Safety Instructions For Installation

6 Safety Instructions For Use, Care, Cleaning And

Disposal

7 FEATURES AND BENEFITS

7 Key Parts and Components

7 Included Accessories

8 INSTALLATION INSTRUCTIONS

8 Choose the Proper Location

8 Power Outlet

8 Flooring

9 Unpacking and Removing Shipping Material

1 0 Connecting the Water Lines

11 Connecting the Drain Hose

12 Leveling the Washer

13 Connect to The Power Supply

14 Sorting Wash Loads

15 About the Dispensers

15 Detergent and Dispenser Use

17 HOW TO USE

17 Control Panel Features

1 8 Time and Status Display

19 Operating the Washer

2 0 Cycle Guide

21 Main Cycle

22 Cycle Modifier Buttons

23 Option Buttons

23 Cold Wash™

23 Delay Wash

23 Fabric Softener

23 Extra Rinse

23 Water Plus

23 Signal On/Off

23 Child Lock

23 Add Garments

24 CARE AND CLEANING

24 Regular Cleaning

24 Cleaning the Exterior

24 Care and Cleaning of the Interior

24 Tub Clean Cycle

24 Removing Mineral Buildup

24 Leave the Lid Open

25 Maintenance

26 Cleaning the Washer

27 SPECIFICATIONS

27 SMART DIAGNOSIS™ SYSTEM

28 TROUBLESHOOTING

28 Normal Sounds You May Hear

28 Before Calling for Service

32 Error Codes

34 WARRANTY

3

ENGLISH

SAFETY MESSAGES

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,

electric shock, or to prevent property damage, injury to persons, or death. Your safety and the safety of

others is very important. There are many important safety messages in this manual and on your appliance.

Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can result in prop-

erty damage and/or serious bodily harm or death.

All safety messages will follow the safety alert symbol and either the word DANGER, WARNING

or CAUTION. These words mean:

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,

and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

You will be killed or seriously injured if you don’t immediately follow instructions.

You can be killed or seriously injured if you don’t follow instructions.

You may be slightly injured or cause damage to the product if you do not follow

instructions.

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic pre-

cautions, including the following.

y Use this appliance only for its intended purpose as described in this owner’s Manual.

y Before use, the washer must be properly installed as described in this manual.

y Do not wash articles that have been previously cleaned in, washed in, soaked in, or spotted with gaso-

line, dry cleaning solvents, or other flammable or explosive substances, as they give off vapors that

could ignite or explode.

y Do not add gasoline, dry cleaning solvents, or other flammable or explosive substances to the wash

water. These substances give off vapors that could ignite or explode.

y Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for

such a period, before using the washer, turn on all hot water faucets and let the water flow from each

for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not

smoke or use an open flame during this time.

y Do not allow children to play on or in the washer. Close supervision of children is necessary when the

washer is used near children.

y Before the washer is removed from service or discarded, remove the lid to prevent children from

climbing inside.

y Do not install or store the washer where it will be exposed to the weather or freezing temperatures.

y Do not tamper with controls.

y Keep the area underneath and around your appliances free of combustible materials (lint, paper, rags,

etc.), gasoline, chemicals and other flammable vapors and liquids.

y Service must be performed by a qualified service technician. Do not disassemble the washer.

y See Installation Instructions for grounding requirements.

y WARNING : This product contains chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm. Wash hands after handling.

BASIC SAFETY PRECAUTIONS

WARNING

CAUTION

DANGER

4

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,

electric shock, or to prevent property damage, injury to persons, or death.

GROUNDING REQUIREMENTS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk

of electric shock by providing a path of least resistance for electric current. This appliance is equipped with

a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an

appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Improper connection of the equipment-grounding conductor can result in risk of electric shock. Check with

a qualified electrician or servicer if you are in doubt as to whether the appliance is properly grounded. Do

not modify the plug provided with the

appliance. If it does not fit the outlet, have a proper outlet installed by a qualified electrician. Failure to fol-

low these warnings can cause serious injury, fire, electric shock, or death.

y ALWAYS follow the fabric care instructions supplied by the garment manufacturer.

y Do not place items exposed to cooking oil in your washer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause a load to catch fire.

y Use fabric softeners or products to eliminate static only as recommended by the manufacturer.

y This washer is not designed for maritime use or for mobile installations such as in RVs, aircraft, etc.

y Turn off the water faucets and unplug the washer if the machine is to be left for an extended period of

time, such as during vacations.

y Do not use to dry articles containing foam rubber or similarly textured rubber-like materials.

y Packaging material can be dangerous for children. There is a risk of suffocation! Keep all packaging from

children.

y Always check the inside of the washer for foreign objects before loading laundry. Keep the lid closed

when not in use.

y Do not reach into the appliance if the tub or agitator is moving.

WARNING

5

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electric shock or injury to persons when using this appliance, follow basic precautions,

including the following:

y Refer to INSTALLATION INSTRUCTIONS for detailed grounding procedures. Installation instructions are

packed with the washer for installer’s reference. If the washer is moved to a new location, have it checked

and reinstalled by a qualified service technician. Failure to follow this warning can cause serious injury, fire,

electric shock, or death.

y Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Failure to

follow this warning can cause serious injury, fire, electric shock, or death.

y For personal safety, this appliance must be properly grounded. Failure to follow this warning can cause seri-

ous injury, fire, electric shock, or death.

y The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall outlet to minimize the possibility of electric shock from this appliance.

y This washer must be plugged into a 120 VAC, 60 Hz grounded outlet. Failure to follow this warning can cause

serious injury, fire, electric shock, or death.

y Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Failure to follow this warning can cause serious injury, fire, electric shock, or death.

y Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have

it replaced with a properly grounded 3-prong wall outlet. Failure to follow this warning can cause serious

injury, fire, electric shock, or death.

y Do not install on carpet. Install washer on a solid floor. Failure to follow this warning can cause serious leak

damage.

y Do not remove ground prong. Do not use an adapter or extension cord. Plug into a grounded 3-prong outlet.

Failure to follow these warnings can cause serious injury, fire, electric shock, or death.

y The washer should always be plugged into its own individual electrical outlet which has a voltage rating that

matches the rating plate. This provides the best performance and also prevents overloading house wiring

circuits which could cause a fire hazard from overheated wires.

y Never unplug your washer by pulling on the power cord. Always grip plug firmly and pull straight out from the

outlet. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

y Repair or immediately replace all power cords that have become frayed or otherwise damaged. Do not use

a cord that shows cracks or abrasion damage along its length or at either end. Failure to follow this warning

can cause serious injury, fire, electric shock, or death.

y When installing or moving the washer, be careful not to pinch, crush, or damage the power cord. Failure to

follow this warning can cause serious injury, fire, electric shock, or death.

y The washer must be installed and electrically grounded by a qualified service person in accordance with local

codes to prevent shock hazard and assure stability during operation.

y The washer is heavy. Two or more people may be needed to install and move the appliance. Failure to do so

can result in back or other injury.

y Store and install the washer where it will not be exposed to temperatures below freezing or exposed to

outdoor weather conditions. Failure to follow this warning can cause serious leak damage.

y Do not install the washer in humid spaces to reduce the risk of electric shock. Failure to follow this warning

can cause serious injury, fire, electric shock, or death.

y To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the

use of long sleeved gloves and safety glasses. Failure to follow all of the safety warnings in this manual could

result in property damage, injury to persons or death.

y Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has miss-

ing or broken parts, including a damaged cord or plug.

y To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the

washer at the household distribution panel by removing the fuse or switching off the circuit breaker before

attempting any maintenance or cleaning.

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,

electric shock, or to prevent property damage, injury to persons, or death.

SAFETY INSTRUCTIONS FOR INSTALLATION

WARNING

6

IMPORTANT SAFETY INSTRUCTIONS

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,

electric shock, or to prevent property damage, injury to persons, or death.

SAVE THESE INSTRUCTIONS

SAFETY INSTRUCTIONS FOR USE, CARE, CLEANING AND DISPOSAL

To reduce the risk of fire, electric shock or injury to persons when using this appliance, follow basic precau-

tions, including the following:

y Unplug the washer before cleaning to avoid the risk of electric shock.

y Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer. They will damage the

finish.

y Do not put oily or greasy rags or clothing on top of the washer. These substances give off vapors that

could ignite the materials.

y Do not wash items that are soiled with vegetable or cooking oil. These items may contain some oil after

laundering. Due to the remaining oil, the fabric may smoke or catch fire by itself.

y Disconnect this appliance from the power supply before attempting any user maintenance. Turning the

controls to the OFF position does not disconnect this appliance from the power supply. Failure to follow

this warning can cause serious injury, fire, electric shock, or death.

y Do not combine laundry products for use in one load unless specified on the label.

y Do not mix chlorine bleach with ammonia or acids such as vinegar. Follow package directions when us-

ing laundry products. Incorrect usage can produce poisonous gas, resulting in serious injury or death.

y Do not reach into the washer while parts are moving. Before loading, unloading, or adding items, press

the START/PAUSE button and allow the drum to coast to a complete stop before reaching inside. Failure

to follow this warning can cause serious injury, fire, electric shock, or death.

y Do not allow children to play on or in the washer. Close supervision of children is necessary when the

washer is used near children. As children grow, teach them the proper, safe use of all appliances. Fail-

ure to comply with these warnings could result in serious injury to persons or death.

y Destroy the carton, plastic bag, and other packing materials after the washer is unpacked. Children

might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight

chambers. Failure to comply with these warnings could result in serious injury to persons or death.

y Keep laundry products out of children’s reach. To prevent injury to persons, observe all warnings on

product labels. Failure to comply with these warnings could result in serious injury to persons or death.

y Remove the lid to the washing compartment to avoid the danger of children or small animals getting

trapped inside before your washer is removed from service or discarded. Failure to do so can result in

serious injury to persons or death.

y Keep hands and foreign objects clear of the lid and latch area when closing the lid. Failure to keep hands

clear can result in personal injury.

y Do not insert hands or arms between the tub and the top cover or cabinet of the washer while cleaning.

Doing so may result in personal injury.

WARNING

7

ENGLISH

FEATURES AND BENEFITS

KEY PARTS AND COMPONENTS

A

INVERTER DIRECT DRIVE MOTOR

The inverter motor, which is directly con-

nected to the tub, produces little noise and

vibration and offers great durability and

long lifespan.

B

NEVERUST™ STAINLESS STEEL

TUB

The full stainless steel tub provides ex-

treme durability and hygienic benefits.

C

CHILD LOCK

Use this option to disable the controls dur-

ing a wash cycle. This option can prevent

children from changing cycles or operating

the machine.

D

SMARTRINSE™ JET SPRAY

This washer is designed to save rinse

water by using SMARTRINSE™ jet spray

in NORMAL, HEAVY DUTY and SPEED

WASH cycles.

E

SLAM PROOF™LID

The Slam Proof™ lid is a safety device that

closes the lid slowly. The Slam Proof™

hinges allow the lid to close gently and qui-

etly, helping prevent injuries.

F

SMART DIAGNOSIS™

If you ever experience an issue with your

LG washer, you don’t have to worry. The

SmartDiagnosis™ feature helps the ser-

vice center diagnose problems over the

phone, or with a simple app on your smart

phone, helping you minimize costly, incon-

venient service calls.

INCLUDED ACCESSORIES

y Tie Strap (for securing drain hose)

y Height adjustment plate

NOTE: Contact LG Customer Service at 1-800-243-

0000 (1-888-542-2623 in Canada) if any accessories

are missing or to purchase accessories.

Drain

Hose

Power

Cord

Dispenser box

(See page 15)

Lid

Control panel

(See page 17)

Bleach

dispenser

Tub

Leveling feet

Cold Water

Inlet valve

Hot Water

Inlet valve

8

INSTALLATION INSTRUCTIONS

CHOOSE THE PROPER LOCATION

POWER OUTLET

y The power outlet must be within 60 in. (1.5 m) of

either side of the washer.

y The appliance and outlet must be positioned so

that the plug is easily accessible.

y Do not overload the outlet with more than one ap-

pliance.

y The outlet must be grounded in accordance with

current wiring electric codes and regulations.

y Time-delay fuse or circuit breaker is recommend-

ed.

NOTE: It is the personal responsibility and obligation

of the product owner to have a proper outlet installed

by a qualified service technician.

FLOORING

y To minimize noise and vibration, the washer MUST

be installed on a solidly constructed floor.

y Allowable slope under the entire washer is a maxi-

mum 1 in. difference from side to side or from

front to back.

y Installing on carpeting and soft tile surfaces is not

recommended.

y Never install the washer on a platform or weakly sup-

ported structure.

To ensure sufficient clearance for water lines and

airflow, allow minimum clearances of at least 1 in.

(2.5 cm) at the sides and 4 in. (10 cm) behind the

unit. Be sure to allow for wall, door, or floor mold-

ings that may increase the required clearances.

Minimum vertical space from floor to overhead

shelves, cabinets, ceilings, etc., is 56 in.

1”

(2.5cm)

24

7

/8”

(63.2 cm)

1”

(2.5cm)

40

1

/8”

(102 cm)

54

3

/4”

(139 cm)

(with open lid)

25 ”

(63.4 cm)

y The washer is heavy. Two or more people

are required when moving and unpacking the

washer. Failure to do so may result in damage

to property or serious bodily harm.

y Store and install the washer where it will not

be exposed to temperatures below freezing

or exposed to outdoor weather conditions.

Failure to follow this warning can cause seri-

ous injury, fire, electric shock, or death.

y Properly ground washer to conform with all

electric governing codes and ordinances. Fail-

ure to follow this warning can cause serious

injury, fire, electric shock, or death.

y To reduce the risk of electric shock, do not

install the washer in humid spaces. Failure to

follow this warning can cause serious injury,

fire, electric shock, or death.

y To ensure proper air flow, do not block the

large opening on the bottom of the washer

with carpeting or other materials.

y Do not remove ground prong. Do not use

an adapter or extension cord. Plug into a

grounded 3-prong outlet. Failure to follow this

warning can cause serious injury, fire, electric

shock, or death.

NOTE: The washer must be installed on firm flooring

to minimize vibration during the spin cycle. Concrete

flooring is best, but a wood floor is sufficient, pro-

vided it is built to FHA standards. The washer should

not be installed on rugs or exposed to weather.

WARNING

3

2

/4”

(9 cm)

26

3

/8”

(67 cm)

30 ”

(76 cm)

9

ENGLISH

INSTALLATION INSTRUCTIONS

UNPACKING AND REMOVING SHIP-

PING MATERIAL

1. After removing the carton and shipping material,

lift the washer off the foam base. Make sure the

plastic tub support comes off with the base and is

not stuck to the bottom of the washer.

If you must lay the washer down to remove the base

packaging materials, always protect the side of the

washer and lay it carefully on its side. DO NOT lay

the washer on its front or back.

2. Save the foam block (that contains the Own-

er’s Manual, parts and laundry product sam-

ples) for future use. If the washer must be

moved in the future, this will help prevent

damage to the washer during transportation.

NOTE: To prevent damage, do not remove the

foam block until the washer is at the final location.

3. Unfasten the power cord from the back of the

washer.

TOOLS YOU WILL NEED

y Adjustable Pliers

y Carpenter's Level

Plastic Tub Support

Carton Base

10

INSTALLATION INSTRUCTIONS

CONNECTING THE WATER LINES

y LG recommends the use of LG hoses. Any leak-

ing, property damage, or damage to the washing

machine caused by an improper installation or by

the use of Non-LG hoses is not covered under the

terms of the LG warranty and is the sole responsi-

bility of the customer and/or an installer.

y Water supply pressure must be between 14.5 psi

and 116 psi (100~800 kPa). If the water supply pressure

is more than 116 psi, a pressure reducing valve must

be installed.

y Periodically check the hose for cracks, leaks, and

wear, and replace the hose if necessary.

y Make sure that the water lines are not stretched,

pinched, crushed, or kinked.

y The washer should never be installed or stored in a

location subject to freezing temperatures. Damage to

the water lines and internal mechanisms of the washer

can result. If the washer was exposed to freezing tem-

peratures prior to installation, allow it to stand at room

temperature for several hours before use and check for

leaks prior to operation.

1. Inspect the threaded fitting on each hose and

make sure there is a rubber seal in place in both

ends.

2. Connect the water supply hoses to the HOT and

COLD water faucets tightly by hand and then tight-

en another 2/3 turn with pliers.

Water Faucet

3. Always run a gallon or two of water through each

inlet hose to flush dirt, scale and other debris out

of the water lines. Doing so will help prevent future

problems with clogged filter screens, and will also

allow you to verify which hose is hot and which

is cold.

4. Attach the hot water line to the hot water inlet on

the back of the washer. Attach the cold water line

to the cold water inlet on the back of the washer.

Tighten the fittings securely. Turn ON both fau-

cets all the way and check for leaks at both ends

of the hoses.

NOTE: Be careful not to cross-thread the hose fit-

tings. This will damage the valve and could result in

property damage from leaks.

Rubber Seal

Water Hose

(to tap)

Water Hose

(to water inlet

on washer)

Rubber Seal

y

Do not reuse old hoses.

Only use new hoses

when you install the washing machine. Old

hoses could leak or burst causing flooding and

property damage.

y

Do not overtighten the hoses.

Overtightening

can damage the valves resulting in leaking and

property damage.

y

Do not overtighten.

Damage to the coupling

can result.

Cold water inlet

Hot water inlet

WARNING

11

ENGLISH

INSTALLATION INSTRUCTIONS

CONNECTING THE DRAIN HOSE

y The drain hose should always be properly secured.

Failure to properly secure the drain hose can result in

flooding and property damage.

y The drain must be installed in accordance with any

applicable local codes and regulations.

y Make sure that the drain hose is not stretched,

pinched, crushed, or kinked.

OPTION 1: STANDPIPE

Bend the outlet end of the drain hose to form a U

shape. Insert the end of the drain hose into the drain.

If the drain is large enough for the flange on the hose

to fit inside, then do not insert the flange more than

1-2 inches into the drain. Use the tie strap included

with the installation materials in the foam block in

the tub to secure the drain hose to the drain.

If the water valves and drain are built into the wall,

fasten the drain hose to one of the water hoses with

the tie strap (ribbed side on inside).

If your drain is a standpipe, fasten the drain hose to

the standpipe with the tie strap provided.

NOTE:

y Normal height of the end of the hose should be ap-

proximately 35”~47” (0.9~1.2 m) from the floor.

y Do not install the end of the drain hose higher

than 96 in. (243.8 cm) above the bottom of the

washer or more than 60 in. (152.4 cm) away from

the washer.

y Never seal the drain hose to the drain such as

with tape. If no air gap is present, water can be

siphoned out of the tub resulting in poor wash/

rinse performance or clothing damage.

OPTION 2: LAUNDRY TUB

Bend the end of the drain hose to the desired shape

and support it on the edge of the laundry tub. Use

the tie strap to secure the drain hose in place.

Drain Hose

Tie Strap

39”

(99 cm)

39”

(99 cm)

Tie Strap

Drain Hose

12

INSTALLATION INSTRUCTIONS

LEVELING THE WASHER

The tub of your new washer spins at very high

speeds. To minimize vibration, noise, and unwanted

movement, the floor must be a level, solid surface.

NOTE:

• Adjust the leveling feet only as far as necessary

to level the washer. Extending the leveling feet

more than necessary can cause the washer to

vibrate.

• Before installing the washer, make sure that the

floor is clean, dry and free of dust, dirt, water

and oils so the washer feet cannot slide easily.

Leveling feet that move or slide on the floor can

contribute to excessive vibration and noise due

to poor contact with the floor.

All four leveling feet must rest solidly on the floor.

Attempt to rock the washer from corner to corner

to make sure that all four leveling feet are in firm

contact with the floor.

1. Position the washer in its final location, taking spe-

cial care not to pinch, strain, or crush the water

and drain lines. Place a level across the top of the

washer.

2. Adjust the leveling feet. Turn clockwise to raise

the washer or counterclockwise to lower it.

3. To make sure that the washer is properly level,

open the lid and look from above to see if the tub

is centered. If the tub is NOT centered (as shown

in the drawing with the X through it), readjust the

front feet. If you have a level, check your washer

with the level.

y To check if the washer is level from side to side,

place a level on the back edge of the lid.

y To check if the washer is level front to back, place

a level at the side of the washer on the edge where

Side to Side

Front to Back

Raise

Lower

y

Using the washing machine without leveling,

it may result in malfunction caused by the

production of excess vibration and noise.

y

Use the leveling feet only when you level the

washing machine.

If you raise the leveling feet

unnecessarily, it may cause abnormal vibration

of the washing machine.

the cabinet side meets the top cover. Do not place

the level on the top of the lid. Using these sur-

faces will result in the washer being unlevel.

y If the leveling feet have been adjusted as much as

possible and the washer is still not level, use the

risers to lift the back leg(s) of the washer to help

level it. To use, press the riser onto the leg. You

can stack up to three risers under one leg.

WARNING

13

ENGLISH

INSTALLATION INSTRUCTIONS

CONNECT TO THE POWER SUPPLY

Washer should be plugged into a 120-VAC, 60-Hz

grounded 3-prong outlet. Plug in the washer.

Improper connection of the equipment-grounding

conductor can result in risk of electric shock. Check

with a qualified electrician or service technician

if you are in doubt as to whether the appliance is

properly grounded. Do not modify the plug pro-

vided with the appliance. If it does not fit the outlet,

have a proper outlet installed by a qualified electri-

cian. Failure to follow these warnings can cause

serious injury, fire, electrical shock, or death.

y

The power outlet must be within 60 inches (1.5

m) of either side of the washer.

y

The appliance and outlet must be positioned so

that the plug is easily accessible.

y

Do not overload the outlet with more than one

appliance.

y

The outlet must be grounded in accordance

with current wiring codes and regulations.

y

Time-delay fuse or circuit breaker is

recommended.

y

It is the personal responsibility and obligation

of the product owner to have a proper outlet

installed by a qualified electrician.

y

Do not use a worn or damaged power cord or

power plug. Replace or repair it immediately.

Failure to do so may result in death, fire, electric

shock, or malfunction.

y

Do not modify the power cord and take care

not to damage it when installing or moving the

washing machine.

Failure to do so may result in

death, fire, electric shock, or malfunction.

y

Make sure that the washing machine is

grounded.

y

Connect this washing machine to a grounded

outlet conforming to the rating prior to use.

Failure to do so may result in fire, electric

shock, or malfunction.

y

Do not use adaptors or extension cords.

The

washing machine should always be plugged

into its own individual electrical outlet which has

a voltage rating that matches the rating plate.

Failure to do so may result in fire, electric shock

or disorder.

y

Do not damage or cut off the ground prong of

the power cord.

Doing so may cause death,

fire, electric shock, or product malfunction.

WARNING

14

INSTALLATION INSTRUCTIONS

FABRIC CARE LABELS

Many articles of clothing include a fabric care label.

Using the chart below, adjust the cycle and option

selections to care for your clothing according to the

manufacturer’s recommendations.

Fabric Care Labels

LOADING THE WASHER

y Check all pockets to make sure that they are empty.

Items such as clips, matches, pens, coins, and keys

can damage both your washer and your clothes.

y Close zippers, hooks, and drawstrings to prevent

these items from snagging or tangling on other

clothes.

y Pretreat heavily stained areas for best results.

y Combine large and small items in a load. Load large

items first.

y Large items should not be more than half of the

total wash load.

y The washer can be fully loaded, but the tub should

not be tightly packed with items. The lid of the

washer should close easily.

y To prevent an out-of-balance load, do not wash sin-

gle items. Add one or two similar items to the load.

Large, bulky items, such as a blanket, comforter, or

bedspread, should be washed individually.

y Do not wash or spin waterproof items, such as rain

coats, sleeping bags, etc.

y The washer will not fill or operate with the lid open.

NOTE: Use the BULKY cycle for large or bulky items

such as poly-filled jackets, comforters, pillows, etc.

These items may not be as absorbent as other laundry

items and should be sorted into a separate wash load

for optimal results.

Bulky items should be placed as far down in the tub

as possible for optimal results. Always place buoy-

ant items at the bottom of the tub. The washer will

automatically detect the load size. Because of the

high-efficiency wash system, the water level may not

completely cover the load.

SORTING WASH LOADS

GROUPING SIMILAR ITEMS

For the best washing results, and to reduce the pos-

sibility of damage to clothing, care should be taken

to sort the clothing into loads that are made up of

similar items.

Mixing different fabric types and/or soil levels can

result in poor wash performance, color transfer, dis-

coloration, fabric damage or linting. Fabrics should

be sorted into groups as described below.

COLORS

Sort articles by color. Wash dark clothes together

in a separate load from light colors or whites. Mix-

ing dark clothes with light clothes can result in dye

transfer or discoloration of the lighter clothes.

SOIL LEVEL

Wash heavily soiled clothing together. Washing

lightly soiled clothing in the same load with heav-

ily soiled clothing could result in poor wash perfor-

mance for the lightly soiled clothing.

FABRIC TYPE

Delicate articles should not be mixed with heavier

or sturdier fabric types. Washing heavier fabrics in

a delicate load can result in poor wash performance

for the heavier fabrics and possible damage to the

delicates.

LINT TYPE

Some fabrics attract and bind lint to them while oth-

ers give off lint in the laundry process. Avoid mixing

these lint collectors and lint producers in the same

load. Mixing these fabrics will result in pilling and

linting on the lint collectors. (For example, lint collec-

tor – knit sweater; lint producer – terry cloth towels.)

SORT LAUNDRY…

By Colors By Soil By Fabric By Lint

White Heavy Delicates Lint Producer

Lights Normal Easy Care Line Collector

Darks Light Sturdy

y Do not load items higher than the top edge of

the tub. Failure to follow this caution can result

in leakage or damage to fabrics.

y Use the BULKY cycle for buoyant or nonabsor-

bent items such as pillows or comforters. Fail-

ure to follow this caution can result in leakage.

y If possible, do not wash any water-resistant

items. If you must, please select the BULKY

cycle.

CAUTION

15

ENGLISH

INSTALLATION INSTRUCTIONS

ABOUT THE DISPENSERS

The automatic dispenser consists of two compart-

ments which hold:

y Liquid fabric softener.

y Liquid or powdered detergent for main wash.

MAIN WASH DETERGENT COMPARTMENT

This compartment holds laundry detergent for the

main wash cycle. The detergent is added to the load

at the beginning of the cycle. Always use High-Effi-

ciency (HE) detergent with your washing machine.

Either powdered or liquid detergent may be used.

Never exceed the manufacturer’s recommendations

when adding detergent. Using too much detergent can

result in detergent buildup in clothing and the washer.

FABRIC SOFTENER COMPARTMENT

This compartment holds liquid fabric softener, which

is automatically dispensed during the final rinse cycle.

Never exceed the manufacturer’s recommendations

when adding softener. Using too much fabric soft-

ener can result in buildup in clothing and the washer.

Either powdered or liquid fabric softener may be

used.

y Always follow the manufacturer’s recommenda-

tions when adding fabric softener. Do not exceed

the maximum fill line. Using too much fabric soft-

ener may stain clothes.

y Dilute concentrated fabric softeners with warm

water. Do not exceed the maximum fill line.

y Never pour fabric softener directly onto the load

or into the tub.

DETERGENT AND DISPENSER USE

A WORD ABOUT DETERGENTS

High-Efficiency (HE) detergents produce fewer suds,

dissolve more efficiently to improve washing and

rinsing performance, and help to keep the interior of

your washer clean. Using detergent that is not HE may

cause oversudsing and unsatisfactory performance

which could result in error codes, cycle failure, and

machine damage.

Maximum

Normal Load Amount

Liquid

Detergent

Powder

Detergent

For proper wash performance, always measure the

detergent using the measurements provided by the

detergent manufacturer.

The normal amount of HE detergent needed, for aver-

age loads, is less than ½ of the recommended maxi-

mum. Use less detergent for soft water, light soil or

smaller loads. Never use more than the maximum

amount recommended by the detergent manufacturer.

DESIGNED TO USE ONLY

HIGH-EFFICIENCY (HE)

DETERGENT

IMPORTANT: Your washing machine is designed for

use with only High-Efficiency (HE) detergents. HE de-

tergents are formulated specifically for High-Efficiency

washers and contain suds-reducing agents. Always

look for the HE symbol when purchasing detergent.

IMPORTANT: Not all detergents are the same. Pay

careful attention to the amount of detergent used

to avoid oversudsing, poor rinsing and detergent

buildup in clothing, and residue buildup that can

contribute to odors in the machine. NEVER use a

cup or scoop other than the one supplied by the

manufacturer of the detergent you are using. Never

use more than the maximum amount of detergent

recommended by the manufacturer. A full scoop or

measure of detergent should only be used for very

large and heavily soiled loads. Using too much de-

tergent can result in detergent buildup in the washer

and in your clothes.

Always measure the detergent amount. While HE

detergents are designed for this type of washing

machine, be careful when measuring the detergent.

For most normal loads, no more than 1/4 to 1/2 of

cap or scoop of HE detergent should be used.

NOTE:

y Extra care must be exercised when using 2X and 3X

concentrated detergents because even a little bit ex-

tra can contribute to the problems mentioned above.

y Detergents designated as HE compatible may not

provide optimal results.

Main wash

Detergent

Compartment

Liquid Fabric

Softener

Compartment

16

INSTALLATION INSTRUCTIONS

USING THE SOFTENER AND DETERGENT

DISPENSER

To add detergent, bleach, and fabric softener to the

automatic dispenser:

1. Open the dispenser drawer.

2. Load the laundry products into the appropriate

compartments.

3. Close the drawer before starting the cycle.

4. If using fabric softener on NORMAL or HEAVY

DUTY cycles, press the FABRIC SOFTENER but-

ton or select the EXTRA RINSE option.

NOTE: It is normal for a small amount of water to

remain in the bleach and softener compartments at

the end of the cycle.

IMPORTANT: Do not place or store laundry prod-

ucts, such as detergent, bleach, or liquid fabric soft-

ener, on top of your washer or dryer. Wipe up any

spills immediately. These products can damage the

finish and controls.

USING THE LIQUID BLEACH DISPENSER

Bleach dispenser

1. Check clothing care labels for special instructions.

2. Measure liquid bleach carefully, following instruc-

tions on the bottle. High-efficiency washers use

less water, so less bleach is needed. One half cup is

enough for most loads.

3. Carefully pour the pre-measured amount of bleach

directly into the bleach dispenser. If you are using

powdered bleach of any kind, pour it directly into the

tub before adding the laundry. Never add powdered

bleach to the liquid bleach dispenser.

y Never pour undiluted liquid chlorine bleach directly

onto clothes or into the tub.

y Do not pour powdered bleach into bleach dispenser.

y Do not place laundry items on top of the bleach dis-

penser when loading and unloading the washer.

y Always measure and pour bleach carefully. Avoid

overfilling or splashing when adding bleach to the

dispenser. The maximum capacity of the bleach dis-

penser is one cup of bleach per wash cycle. Overfill-

ing could result in bleach being dispensed immedi-

ately, which can result in damage to the clothes in the

washer.

17

ENGLISH

HOW TO USE

CONTROL PANEL FEATURES

A

POWER (ON/OFF) BUTTON

Press to turn the washer ON. Press

again to turn the washer OFF. Pressing

the POWER button during a cycle will

cancel that cycle and any load settings

will be lost. The lid will unlock after a

brief pause.

NOTE: If there is any water remaining

in the tub after the washer shuts off, it

will drain following a five minute delay.

The washer can be restarted any time

before the drain begins. However, once

the water begins to drain, all functions

will be suspended until the water has

been completely drained and the washer

shuts off.

B

CYCLE SELECTOR BUTTON

Press the Cycle Button repeatedly until

the desired cycle is selected. Once the

desired cycle has been selected, the

standard presets will appear in the dis-

play. These settings can be adjusted

using the cycle setting buttons anytime

before starting the cycle.

NOTE: To protect your clothing, not all

settings are available on all cycle selec-

tions.

C

START/PAUSE BUTTON

Press this button to start the selected

cycle. If the washer is running, use this

button to pause the cycle without losing

the current settings.

NOTE: If you do not press the START/

PAUSE button within five minutes of se-

lecting a cycle, the washer automatically

turns OFF and all cycle settings are lost.

Any water remaining in the tub will drain

after a five minute delay.

D

CYCLE MODIFIER BUTTONS

Use these buttons to adjust the settings

for the selected cycle. The setting lights

above the buttons illuminate to show the

current selection.

E

SPECIAL CYCLE AND OPTION BUTTONS

These buttons allow you to select special

cycles or options.

F

TIME AND STATUS DISPLAY

The display shows the cycle status and

estimated time remaining.

HOW TO USE

D E

CB

F

A

18

HOW TO USE

TIME AND STATUS DISPLAY

The time and status display shows the estimated time remaining and cycle progress.

A

CYCLE STATUS INDICATOR

These LEDs will illuminate when a cycle

is selected to indicate which stages will

run. When a cycle is running, the LED for

the active stage will blink, and the LEDs

for the remaining stages will remain

steady. Once a stage is complete, the

LED will turn off. If a cycle is paused, the

active stage LED will stop blinking.

B

DELAY WASH INDICATOR

The Delay Wash Indicator will illuminate

when a delay wash is set. The indica-

tor light will turn off once the cycle has

started.

C

ESTIMATED TIME REMAINING

When a cycle is selected, the default

time for that cycle is displayed. This time

will change as modifiers or options are

selected. Once the START/PAUSE but-

ton is pressed, the washer will measure

the size of the load. The estimated time

may change once the load size has been

measured. If Delay Wash is set, the re-

maining delay time counts down until the

cycle begins.

NOTE: The time shown is only an esti-

mate. This time is based on normal oper-

ating conditions. Several external factors

(load size, room temperature, incoming

water temperature, etc.) can affect the

actual time.

D

LID LOCK INDICATOR

The Lid lock indicator will illuminate once

a cycle has started. The indicator light

will stay on until the cycle is paused,

stopped or has finished.

B

D

C

A

19

ENGLISH

HOW TO USE

OPERATING THE WASHER

1

SORT LAUNDRY AND LOAD THE WASHER

Sort laundry by fabric type, soil level, color and

load size, as needed. Open the lid and load items

into the washer.

Bleach dispenser

2

CLEANING PRODUCT

Add High-Efficiency (HE) detergent to the deter-

gent dispenser. If bleach or fabric softener is to

be used, add these to the appropriate dispenser.

3

TURN ON THE WASHER

Press the POWER button to turn ON the washer.

The lights above the cycle buttons will illuminate

and a chime will sound.

4

CYCLE SELECTOR BUTTON

Press the Cycle Button repeatedly until the desired

cycle is selected. The preset Wash Temp., Spin

Speed, Soil Level and option settings for that cycle

will be shown. Pressing the Start Pause button with-

out selecting a cycle will cause the NORMAL cycle

to begin immediately.

5

ADJUST SETTINGS

Default settings for the selected cycle can now

be changed, if desired, using the cycle modifier

and option buttons.

NOTE: Not all modifiers and options are available

on all cycles. A different chime will sound and the

LED will not come on if the selection is not allowed.

6

BEGIN CYCLE

Press the START/PAUSE button to begin the

cycle. The lid will lock, and the washer will agi-

tate briefly without water to measure the weight

of the load. If the START/PAUSE button is not

pressed within 5 minutes, the washer will shut

off and all settings will be lost.

7

ADD GARMENTS LIGHT

The ADD GARMENTS light will illuminate near

the beginning of the wash cycle to indicate when

it is safe to add items to the load. Press the

START/PAUSE button to pause the cycle and add

garments to the load. Press the START/PAUSE

button to resume the cycle.

NOTE: It is not recommended to add items un-

less the ADD GARMENTS light is illuminated, as

this could result in poor performance.

8

END OF CYCLE

When the cycle is finished, a melody will sound.

Immediately remove your clothing from the

washer to reduce wrinkling.

y

To reduce the risk of fire, electric shock, or injury to persons,

read the IMPORTANT SAFETY

INSTRUCTIONS before operating this appliance.

WARNING

Main Wash

Detergent

Fabric Softener

20

HOW TO USE

CYCLE GUIDE

The cycle guide below shows the default settings, available options

and recommended fabric types for each cycle. Allowable modifier ad-

justments are shown below the default setting for each cycle.

=

AVAILABLE OPTION

= Default Setting

Cycle

Fabric or

Load Type

Wash

Temp.

Spin

Speed

Soil Level

Cold

Wash™

Extra

Rinse

Fabric

Softener

Water

Plus

Normal

Cotton, linen,

towels, shirts,

sheets, jeans,

mixed loads

Warm High Normal

Hot Medium Heavy

Eco Warm No Spin Light

Cold

Tap Cold

Heavy Duty

Heavy soiled

cotton fabrics

Warm High Heavy

Hot Medium Normal

Eco Warm Low Light

Cold No Spin

Tap Cold

Bulky

Large items such

as blankets and

comforters

Warm High Normal

Hot Medium Heavy

Eco Warm Low Light

Cold No Spin

Tap Cold

* Use the BULKY cycle for items such as pillows, comforters, pet bedding and other articles which have

difficultly absorbing water. DO NOT WASH EXCESSIVELY LARGE ITEMS. If large/bulky items do not

fit easily into the tub, there may not be enough room for them to move during washing. Keep like items

together; do not mix large bulky items with smaller clothing items. Failure to follow these instructions

may result in damage to the clothing or to the washer.

Tub Clean Refer to page 24.

Hot High Light

Speed

Wash

Lightly soiled and

small loads

Warm High Light

Eco Warm Medium Heavy

Cold Low Normal

Tap Cold No Spin

Delicates

Dress shirts/

blouses, nylons,

sheer or lacy

garments (less

than 8 lbs.)

Tap Cold Low Light

Warm High Heavy

Eco Warm Medium Normal

Cold No Spin

Rinse+Spin

Tap Cold High

Medium

Low

No Spin

Spin Only

High

NOTE:

To protect your garments, not every wash/rinse temperature, spin speed, soil level, or option is available with

every cycle. A chime will sound and the LED will not light if the selection is not allowed.

*When a cycle is selected, the default time for that cycle is displayed. This time will change as modifiers or

options are selected. Once the START/PAUSE button is pressed, the washer will measure the size of the

load. The estimated time may change once the load size has been measured. The washer automatically

adjusts the wash time for the amount of laundry, water pressure, water and other operating conditions.

La page charge ...

LG WT1001CW Le manuel du propriétaire

LG WT1001CW Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents