Hestan KRD364GD-NG Guide d'installation

Marque: Hestan

Modèle: KRD364GD-NG

Catégorie: Cuisinières

Taper: Guide d'installation

Ce manuel convient également à

INDOOR COOKING

Dual-Fuel Range

KRD

Installation Manual

SAFETY DEFINITIONS

THIS INDICATES THAT DEATH OR SERIOUS INJURY MAY OCCUR

AS A RESULT OF NOT OBSERVING THIS WARNING.

THIS INDICATES THAT MINOR OR MODERATE INJURY MAY

OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING.

THIS INDICATES THAT DAMAGE TO THE APPLIANCE OR

PROPERTY MAY OCCUR AS A RESULT OF NOT OBSERVING THIS

WARNING.

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE

INSTALLING OR USING YOUR APPLIANCE TO REDUCE THE RISK OF FIRE,

BURN HAZARD, OR OTHER INJURY. KEEP THIS MANUAL FOR FUTURE

REFERENCE.

CAUTION

NOTICE

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of

this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

1. Do not try and light any appliance.

2. Do not touch any electrical switch.

3. Do not use any phone in your building.

4. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

5. If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas

supplier.

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY,

A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE,

PERSONAL INJURY, OR DEATH.

INSTALLER: LEAVE THIS MANUAL WITH THE OWNER OF THE APPLIANCE.

HOMEOWNER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

TIP OVER HAZARD

A child or adult can tip over a range and be killed.

Check installation of the anti-tip device per the Installation Manual.

Do not operate the range without this device in place.

Check engagement of anti-tip device if range is moved, such as when cleaning behind the unit.

To check engagement, carefully tip the range forward while pulling from the rear of the unit. The

range should not move more that 1 inch [2.5cm].

Failure to follow these instructions can result in death or serious burns to children and adults.

To reduce the risk of burns, do not move this appliance while hot.

When properly cared for, your Hestan appliance will provide safe, reliable service for many years.

When using this appliance, basic safety practices must be followed as outlined below.

IMPORTANT: Save these instructions for the local Gas or Utility Inspector’s use.

INSTALLER: Please leave these Installation Instructions with the owner.

OWNER: Please retain these Installation Instructions for future reference.

This range is NOT designed for installation in manufactured (mobile) homes or recreational park

trailers. Do NOT install this range outdoors.

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

ELECTRICAL SHOCK HAZARD

Disconnect power before installing or servicing appliance. Before turning

power ON, be sure all controls are in the OFF position. Failure to do so can

result in electrical shock or death.

ELECTRICAL GROUNDING

This appliance must be grounded. Grounding reduces the risk of electric shock

in the event of a short circuit. Read the ELECTRICAL CONNECTIONS section of this manual for

complete instructions.

This appliance is equipped with a 4-prong grounding plug for your protection against shock hazard

and should be directly plugged into a properly grounded receptacle. Do not cut or remove the

grounding prong from this plug.

ELECTRICAL SUPPLY

The appliance must be on its own dedicated circuit - 240 VAC, Single Phase, 60 Hz, with a current

rating as shown in the model number listing on pg. 2. Have the installer show you where the

electric circuit breaker is located so you know how to shut off the power to this appliance. It is the

responsibility of the user to have the appliance connected by a licensed electrician in accordance

with all local codes, or in the absence of local codes, in accordance with the National Electrical

Code. Read the ELECTRICAL CONNECTIONS section of this manual for complete details.

TABLE OF CONTENTS

1 SAFETY PRECAUTIONS - BEFORE YOU BEGIN

2 MODEL NUMBERS

3 RATING LABEL

3 REGULATORY / CODE REQUIREMENTS

3 LOCATION AND INSTALLATION / VENTILATION

14 BACKGUARD AND ACCESSORIES

15 INSTALLATION OF ANTI-TIP DEVICE

16 ELECTRICAL CONNECTIONS

18 GAS CONNECTION

20 FINAL SETUP

21 SERVICE

22 APPENDIX

MODEL NUMBERS

RANGE MODELS

MODEL NO. DESCRIPTION

CIRCUIT BREAKER

REQUIRED

KRD304-NG / -LP 30” DUAL-FUEL RANGE WITH 4 BURNERS 40 Amp

KRD365-NG / -LP 36” DUAL-FUEL RANGE WITH 5 BURNERS 40 Amp

KRD364GD-NG / -LP 36” DUAL-FUEL RANGE WITH 4 BURNERS & 12” GRIDDLE 40 Amp

KRD485GD-NG / -LP 48” DUAL-FUEL RANGE WITH 5 BURNERS, 2 OVENS, & 12”GRIDDLE 50 Amp

KRD484GD-NG / -LP 48” DUAL-FUEL RANGE WITH 4 BURNERS, 2 OVENS, & 24”GRIDDLE 50 Amp

KRD485GDKRD365

KRD364GD

KRD484GD

KRD304

REGULATORY / CODE REQUIREMENTS

Installation of this cooking appliance must be made in accordance

with local codes. In the absence of local codes, this unit should

be installed in accordance with the National Fuel Gas Code

ANSI

Z223.1/NFPA 54

, Natural Gas and Propane Installation code

CSA

B149.1

, or Propane Storage and Handling Code

B149.2

All Electrical Components must be electrically grounded in

accordance with local codes or in the absence of local codes with

the National Electrical Code

ANSI/NFPA 70

, or Canadian Electrical

code

CSA C22.1

STATE OF MASSACHUSETTS

Massachusetts requires all gas be installed using a plumber or gas fitter carrying the appropriate

Massachusetts license. All permanently installed natural gas or propane installations require a

T handle type manual gas valve be installed in the gas supply line to this appliance. Flexible gas

connector must not be longer than 48” [1.2 m].

CALIFORNIA PROPOSITION 65 - WARNING

WARNING This product can expose you to chemicals including carbon monoxide, which is

known to the State of California to cause birth defects or other reproductive harm.

For more information, go to www.P65Warnings.ca.gov.

RATING

LABEL

RATING LABEL

The rating label contains important information about your

Hestan appliance such as the model and serial number,

gas type and manifold pressure, electrical rating, the BTU

rating for each burner type, and the minimum installation

clearances.

The rating label is located in one of two places, as shown in

the figures on this page.

If service is necessary, contact Hestan Customer Care with

the model and serial number information shown on the label.

RATING LABEL

LOCATION AND INSTALLATION / VENTILATION

UNPACKING AND PLACEMENT

Remove the outer carton and packing materials from the shipping pallet. Do not remove the plastic

film covering the stainless-steel surfaces. This film protects the finish from scratches until the

appliance is installed in its final position.

The unit is very heavy and should be handled with care. Use proper safety equipment, such as gloves,

and at least 2 persons to move the appliance into position to avoid injury and to avoid damage to the

floor or the appliance itself.

DO NOT USE A HAND TRUCK OR DOLLY ON THE FRONT OR REAR OF THE

RANGE. HANDLE AND MOVE FROM THE SIDES ONLY.

Do not lift or carry the appliance by the oven door or handle. This could damage

the door hinges.

NOTICE

LOCATION AND INSTALLATION / VENTILATION

(CONTINUED)

The range is held onto the pallet with 4 large shipping bolts on both sides. Remove these bolts and

then move the range to the floor with the help of 2 persons.

PREPARATION

Before moving the range, protect any finished flooring and

secure the oven door(s) closed to prevent damage.

GAS AND ELECTRICAL SUPPLY CLEARANCES

If not already in place, install a gas shut-off valve in an

easily accessible location for servicing of the range. Make

sure all users of the range know where this shut-off is

located, and how to shut off the gas. Any openings in the

wall or floor behind the appliance must be sealed. The

Installation Clearances on the following pages show where

the “G” and “E” zones should be located.

The range is designed to be installed nearly flush to the rear

wall*. It may be necessary to reposition the gas supply and

power receptacle / junction box in order to accommodate the range when pushed back against the

wall.

Wall-mounted junction box may protrude no more than 2-3/8” [6.1 cm] from wall and still allow the

back of the range to be nearly flush to rear wall.

* Unless installed in an island with no rear wall.

GAS

SUPPLY

APPLIANCE

SHUTOFF VALVE

IN OPEN POSITION

1-5/16"

[3.3 cm]

POWER

CORD

JUNCTION BOX

INSIDE WALL

CABINETRY

To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space

located above the surface units should be avoided. If cabinet storage is to be provided, the risk can

be reduced by installing the required vent hood that projects horizontally a minimum of 5” [12.7 cm]

beyond the bottom of the cabinets.

[5.1 cm]

RECEPTACLE

NEMA 14-50

JUNCTION

BOX

CONDUIT

OVEN DOOR REMOVAL

If you have a very narrow door opening to your kitchen, the oven door(s) can be removed.

REMOVE ONLY IF ABSOLUTELY NECESSARY. Door removal should only be done by a certified

installer or service technician. Be sure the oven has completely cooled and the electrical power is

off. Failure to do so may result in electric shock or burn injury. Use caution when removing the

door, it is very heavy. Be careful to disconnect the wire inside the door.

1. Open oven door completely.

2. Locate cover near hinge to access wire connector inside. Using small needle-nose pliers and a

small flat-blade screwdriver, disconnect the wires inside the door. [ A ]

3. At each hinge location, swing the hinge clip forward until it stops. A screwdriver may be

needed to do this. [ B ]

4. Gently close the oven door until it stops against the hinge clips, or approximately 30° from the

closed position. Hold on firmly to both sides of the door (not the handle) and pull the door

straight up off the hinges. Ask an assistant to help direct the wires out of the bottom of the

door so it does not hang up on anything. Place the oven door in a safe location until needed.

NEVER release the hinge clips and try to close the hinges. Doing so will snap the hinges closed

with great force which could cause injury. [ C & D ]

COVER PLATE

AND SCREW

HINGE CLIP

Hinge

clip

LOCATION AND INSTALLATION/VENTILATION

(CONTINUED)

RE-INSTALL OVEN DOOR

1. Hold the door firmly on both sides (NOT FROM THE HANDLE) at approximately 30° from the

closed position and insert the hinges into the slots in the oven. The bottom edge of each hinge

has a notch which must seat inside the slot opening. DO NOT FORCE OR BEND OR TWIST

THE DOOR! [ E & F ]

2. Slowly open the door all the way. Swing the hinge clips away from you until completely inside

the slot opening and fully seated. A screwdriver may help you do this. [ G ]

3. Re-attach the wire connector and assure it is securely inside the door. Re-install the cover. [ H ]

4. Gently close the oven door to check for smooth operation.

LOCATION AND INSTALLATION/VENTILATION

(CONTINUED)

LEVELING

The range must be level, especially those models featuring a griddle. Raise or lower the range to the

desired height by adjusting the leveling legs under the range. The legs can be turned by hand. It may

be necessary to use a lever or other lifting device to assist in temporarily raising the unit to turn the

legs. Do not lift or lever from the front or back, only from the sides.

Leveling 48” models: The 48” ranges have 6 legs. They should be adjusted so that all six share the

weight of the range.

The appliance top must be

level with or higher than

the adjacent countertop

surfaces. Failure to adjust

the height may expose the

adjacent cabinets to excessive

heat which may damage the

cabinets or countertop.

CAUTION

INSTALLATION CLEARANCES WITH LOW BACKGUARD

SIDE VIEW

38-3/8 - 36-7/8”

[97.5 - 93.7]

TO COOKING

SURFACE

APPLIANCE

TOP

HANDLE

END CAP

COOKING

SURFACE

COMBUSTIBLE

MATERIALS

30-13/16”

[78.3]

24-11/16”

[62.7]

13” [33]

7” [17.7]

2-5/8”

[6.7]

MAX.

LOW

BACKGUARD

MAX.

RECESS

DEPTH

FINISHED

FLOOR

48-5/16”

[122.7]

3”

[7.6]

DIMENSIONS IN BRACKETS [ ] ARE IN CM.

LOCATION OF GAS AND

ELECTRICAL ON FLOOR

REF 1.12”

[2.84 cm]

LOCATION AND INSTALLATION/VENTILATION

(CONTINUED)

RECOMMENDED

GAS SHUT-OFF

VALVE LOCATION

ELECTRICAL

SUPPLY

LOCATION

FINISHED

FLOOR

VENT HOOD

COMBUSTIBLE

MATERIALS

MIN. CLEARANCE

TO NEAREST

COMBUSTIBLE

SIDE SURFACE

DIMENSIONS IN

BRACKETS [ ] ARE

IN CM.

COUNTERTOP

FULL OVERLAY

DRAWER FACE

FULL OVERLAY

CABINET DOOR FACE

[3.2 mm]

INSTALLATION CLEARANCES 30” WITH LOW BACKGUARD

FRONT VIEW

18" [45.7]

MIN.

18"

[45.7]

[17.8]

12"

[30.5]

1-1/2"

[3.8]

[10.2]

11"

[27.9]

2-1/2"

[6.4]

RANGE MODEL

V (MIN)

KRD304 30” [76.2] 30” [76.2]

NOTES:

• SHADED AREAS INDICATE WHERE COMBUSTIBLE MATERIALS ARE NOT ALLOWED.

• APPLIANCE TOP MUST BE LEVEL OR HIGHER THAN THE ADJACENT COUNTERTOP SURFACES.

• “G” IS GAS CONNECTION ZONE ON REAR WALL. MOUNT SHUT-OFF VALVE AS HIGH AS POSSIBLE IN THIS

ZONE FOR EASY ACCESS WHEN RANGE IS INSTALLED.

• “E” IS ELECTRICAL SUPPLY ZONE.

• “W” IS APPLIANCE OPENING.

NOTE: HANDLE END CAPS PROTRUDE 1/8” BEYOND EACH SIDE OF THE RANGE. ALLOWANCE MAY BE

NEEDED FOR ADJACENT DRAWERS OR CABINETRY.

• “V” IS MIN. CLEARANCE TO REQUIRED VENTILATION HOOD.

LOCATION AND INSTALLATION/VENTILATION

(CONTINUED)

INSTALLATION CLEARANCES 36” WITH LOW BACKGUARD

FRONT VIEW

VALVE LOCATION

VENT HOOD

MIN. CLEARANCE

TO NEAREST

COMBUSTIBLE

SIDE SURFACE

COMBUSTIBLE

MATERIALS

12”

[30.5]

2-1/2”

[6.4]

6”

[15.2]

5”

[12.7]

FINISHED

FLOOR

DIMENSIONS IN

BRACKETS [ ] ARE

IN CM.

3”

[7.6]

5”

[12.7]

19”

[48.3]

[24.1]

ELECTRICAL

SUPPLY

LOCATION

18” [45.7]

MIN.

9-1/2”

RECOMMENDED

GAS SHUT-OFF

[45.7]

18”

COUNTERTOP

FULL OVERLAY

DRAWER FACE

FULL OVERLAY

CABINET DOOR FACE

[3.2 mm]

RANGE MODEL

V (MIN)

KRD365 36” [91.4] 30” [76.2]

KRD364GD 36” [91.4] 30” [76.2]

NOTES:

• SHADED AREAS INDICATE WHERE COMBUSTIBLE MATERIALS ARE

NOT ALLOWED.

• APPLIANCE TOP MUST BE LEVEL OR HIGHER THAN THE ADJACENT COUNTERTOP SURFACES.

• “G” IS GAS CONNECTION ZONE ON REAR WALL. MOUNT SHUT-OFF VALVE AS HIGH AS POSSIBLE IN THIS

ZONE FOR EASY ACCESS WHEN RANGE IS INSTALLED.

• “E” IS ELECTRICAL SUPPLY ZONE.

• “W” IS APPLIANCE OPENING.

NOTE: HANDLE END CAPS PROTRUDE 1/8” BEYOND EACH SIDE OF THE RANGE. ALLOWANCE MAY BE

NEEDED FOR ADJACENT DRAWERS OR CABINETRY.

• “V” IS MIN. CLEARANCE TO REQUIRED VENTILATION HOOD.

LOCATION AND INSTALLATION/VENTILATION

(CONTINUED)

DIMENSIONS IN BRACKETS [ ] ARE IN CM.

18” [45.7]

MIN.

RECOMMENDED

GAS SHUT-OFF

VALVE LOCATION

VENT HOOD

COMBUSTIBLE

MATERIALS

4”

[10.2]

11”

[27.9]

23”

[58.4]

7”

[17.8]

ELECTRICAL

SUPPLY

LOCATION

1-1/2”

[3.8]

12”

[30.5]

MIN. CLEARANCE

TO NEAREST

COMBUSTIBLE

SIDE SURFACE

FINISHED

FLOOR

[45.7]

18”

INSTALLATION CLEARANCES WITH LOW BACKGUARD

FRONT VIEW

48"

COUNTERTOP

FULL OVERLAY

DRAWER FACE

FULL OVERLAY

CABINET DOOR FACE

[3.2 mm]

RANGE MODEL

V (MIN)

KRD485GD 48” [121.9] 30” [76.2]

KRD484GD 48” [121.9] 30” [76.2]

NOTES:

• SHADED AREAS INDICATE WHERE COMBUSTIBLE MATERIALS

ARE NOT ALLOWED.

• APPLIANCE TOP MUST BE LEVEL OR HIGHER THAN THE

ADJACENT COUNTERTOP SURFACES.

• “G” IS GAS CONNECTION ZONE ON REAR WALL. MOUNT SHUT-OFF VALVE AS HIGH AS POSSIBLE IN THIS

ZONE FOR EASY ACCESS WHEN RANGE IS INSTALLED.

• “E” IS ELECTRICAL SUPPLY ZONE.

• “W” IS APPLIANCE OPENING.

NOTE: HANDLE END CAPS PROTRUDE 1/8” BEYOND EACH SIDE OF THE RANGE. ALLOWANCE MAY BE

NEEDED FOR ADJACENT DRAWERS OR CABINETRY.

• “V” IS MIN. CLEARANCE TO REQUIRED VENTILATION HOOD.

LOCATION AND INSTALLATION/VENTILATION

(CONTINUED)

INSTALLATION CLEARANCES WITH ISLAND TRIM

SIDE VIEW

FINISHED

FLOOR

38-3/8 - 36-7/8”

[97.5 - 93.7]

TO COOKING

SURFACE

48-5/16”

[122.7]

DIMENSIONS IN BRACKETS [ ] ARE IN CM.

LOCATION OF GAS

AND ELECTRICAL

ON FLOOR

ISLAND

TRIM

For Island Trim installations,

counter surface should

have a cantilever surface

meeting the rear of

the Island Trim

MIN. CLEARANCE

TO COMBUSTIBLE

SURFACES WITH

ISLAND TRIM

COMBUSTIBLE

MATERIALS

30-13/16”

[78.3]

24-11/16”

[62.7]

12”

[30.5]

3”

[7.6]

MAX.

RECESS

DEPTH

APPLIANCE

TOP

COOKING

SURFACE

7” [17.7]

2-5/8”

[6.7]

HANDLE

END CAP

REF 1.12”

[2.84 cm]

LOCATION AND INSTALLATION/VENTILATION

(CONTINUED)

RECOMMENDED

GAS SHUT-OFF

VALVE LOCATION

ELECTRICAL

SUPPLY

LOCATION

FINISHED

FLOOR

COMBUSTIBLE

MATERIALS

MIN. CLEARANCE

TO NEAREST

COMBUSTIBLE

SIDE SURFACE

DIMENSIONS IN

BRACKETS [ ] ARE

IN CM.

COUNTERTOP

FULL OVERLAY

DRAWER FACE

FULL OVERLAY

CABINET DOOR FACE

[3.2 mm]

INSTALLATION CLEARANCES 30” WITH ISLAND TRIM

FRONT VIEW

1-1/2"

[3.8]

[10.2]

11"

[27.9]

2-1/2"

[6.4]

[17.8]

18"

[45.7]

12"

[30.5]

NOTES:

• SHADED AREAS INDICATE WHERE COMBUSTIBLE MATERIALS ARE NOT ALLOWED.

• APPLIANCE TOP MUST BE LEVEL OR HIGHER THAN THE ADJACENT COUNTERTOP SURFACES.

• “G” IS GAS CONNECTION ZONE ON REAR WALL. MOUNT SHUT-OFF VALVE AS HIGH AS POSSIBLE IN THIS

ZONE FOR EASY ACCESS WHEN RANGE IS INSTALLED.

• “E” IS ELECTRICAL SUPPLY ZONE.

• “W” IS APPLIANCE OPENING.

NOTE: HANDLE END CAPS PROTRUDE 1/8” BEYOND EACH SIDE OF THE RANGE. ALLOWANCE MAY BE

NEEDED FOR ADJACENT DRAWERS OR CABINETRY.

• “V” IS MIN. CLEARANCE TO REQUIRED VENTILATION HOOD.

RANGE MODEL

V (MIN)

KRD304 30” [76.2] 30” [76.2]

LOCATION AND INSTALLATION/VENTILATION

(CONTINUED)

COUNTERTOP

FULL OVERLAY

DRAWER FACE

FULL OVERLAY

CABINET DOOR FACE

[3.2 mm]

12”

[30.5]

RECOMMENDED

GAS SHUT-OFF

VALVE LOCATION

FINISHED

FLOOR

MIN. CLEARANCE

TO NEAREST

COMBUSTIBLE

SIDE SURFACE

COMBUSTIBLE

MATERIALS

DIMENSIONS IN

BRACKETS [ ]

ARE IN CM.

3”

[7.6]

5”

[12.7]

6”

[15.2]

5”

[12.7]

2-1/2”

[6.4]

19”

9-1/2”

[24.1]

ELECTRICAL

SUPPLY

LOCATION

[48.3]

[45.7]

18”

INSTALLATION CLEARANCES 36” WITH ISLAND TRIM

FRONT VIEW

RANGE MODEL

V (MIN)

KRD365 36” [91.4] 30” [76.2]

KRD364GD 36” [91.4] 30” [76.2]

NOTES:

• SHADED AREAS INDICATE WHERE COMBUSTIBLE MATERIALS ARE NOT ALLOWED.

• APPLIANCE TOP MUST BE LEVEL OR HIGHER THAN THE ADJACENT COUNTERTOP SURFACES.

• “G” IS GAS CONNECTION ZONE ON REAR WALL. MOUNT SHUT-OFF VALVE AS HIGH AS POSSIBLE IN THIS

ZONE FOR EASY ACCESS WHEN RANGE IS INSTALLED.

• “E” IS ELECTRICAL SUPPLY ZONE.

• “W” IS APPLIANCE OPENING.

NOTE: HANDLE END CAPS PROTRUDE 1/8” BEYOND EACH SIDE OF THE RANGE. ALLOWANCE MAY BE

NEEDED FOR ADJACENT DRAWERS OR CABINETRY.

• “V” IS MIN. CLEARANCE TO REQUIRED VENTILATION HOOD.

LOCATION AND INSTALLATION/VENTILATION

(CONTINUED)

INSTALLATION CLEARANCES 48" WITH ISLAND TRIM

FRONT VIEW

RECOMMENDED

GAS SHUT-OFF

VALVE LOCATION

ELECTRICAL

SUPPLY

LOCATION

FINISHED

FLOOR

COMBUSTIBLE

MATERIALS

MIN. CLEARANCE

TO NEAREST

COMBUSTIBLE

SIDE SURFACE

7”

[17.8]

12”

[30.5]

4”

[10.2]

1-1/2”

[3.8]

11”

[27.9]

23”

[58.4]

[45.7]

18”

COUNTERTOP

FULL OVERLAY

DRAWER FACE

FULL OVERLAY

CABINET DOOR FACE

[3.2 mm]

DIMENSIONS IN

BRACKETS [ ] ARE

IN CM.

RANGE MODEL

V (MIN)

KRD485GD 48” [121.9] 30” [76.2]

KRD484GD 48” [121.9] 30” [76.2]

NOTES:

• SHADED AREAS INDICATE WHERE COMBUSTIBLE MATERIALS ARE NOT ALLOWED.

• APPLIANCE TOP MUST BE LEVEL OR HIGHER THAN THE ADJACENT COUNTERTOP SURFACES.

• “G” IS GAS CONNECTION ZONE ON REAR WALL. MOUNT SHUT-OFF VALVE AS HIGH AS POSSIBLE IN THIS

ZONE FOR EASY ACCESS WHEN RANGE IS INSTALLED.

• “E” IS ELECTRICAL SUPPLY ZONE.

• “W” IS APPLIANCE OPENING.

NOTE: HANDLE END CAPS PROTRUDE 1/8” BEYOND EACH SIDE OF THE RANGE. ALLOWANCE MAY BE

NEEDED FOR ADJACENT DRAWERS OR CABINETRY.

• “V” IS MIN. CLEARANCE TO REQUIRED VENTILATION HOOD.

LOCATION AND INSTALLATION/VENTILATION

(CONTINUED)

BACKGUARD AND ACCESSORIES

Sheetmetal accessories such as the backguard, and areas at the rear of the range may have sharp

edges. Wear work gloves while handling and installing these items.

BACKGUARD

Your Hestan range is supplied at the factory with an Island Trim backguard. See Table 1 in the

APPENDIX section of this manual for other backguard options available from your Hestan dealer.

Selection of the appropriate backguard depends on the installation location and adjacent materials,

and the type of vent hood to be used. Installation instructions are included with the backguard

kit. A LOW OR TALL BACKGUARD IS REQUIRED WHEN INSTALLING THE RANGE AGAINST A

COMBUSTIBLE SURFACE - THE ISLAND TRIM IS NOT SUITABLE.

The top of the backguard serves as an exhaust for the oven when in operation, and as an exhaust vent

to remove heat from under the cooktop section of the range as well. DO NOT BLOCK or obstruct

the top of the backguard. DO NOT touch the top of the backguard during appliance operation as it

may get hot. Allow sufficient time to cool before touching or cleaning this area.

DO NOT position plastic or other heat-sensitive items nearby which could melt or burn.

Griddle Vent - Units with gas griddle have a vent at the rear which must not be obstructed. Do not

attempt to operate the griddle with anything covering or obstructing the griddle vent.

CAUTION

VENTILATION REQUIREMENTS

It is strongly recommended that this appliance be installed with a Hestan vent hood. Due to the high

heat output of this range, it is very important that the hood and ductwork installation meets local

building codes and is installed by a qualified technician.

Do not use a down-draft style ventilation system.

Do not mount a microwave oven/ventilator combination above the range. These type of units do not

have sufficient airflow to remove the high heat output of this range and were not tested with this

type of appliance.

For non-Hestan approved vent hoods, the vent hood and/or blower unit must be rated for 1 CFM

[1.7 m³/hr] for every 100 BTU [.03 kW].

• If the range has a 12” Griddle, add an additional 200 CFM [340 m³/hr] to the blower capacity.

• If the range has a 24” Griddle, add an additional 400 CFM [680 m³/hr] to the blower capacity.

For island applications, it is recommended to use a vent hood that is 6” [15.2 cm] wider than the

appliance, to allow for 3” [7.6 cm] of overlap on the left and right of the appliance.

Keep duct runs as short and straight as possible. Elbows and transition fittings reduce airflow

efficiency. Hestan recommends keeping the duct run under 50 ft. [15.2 m].

CONSULT WITH YOUR HESTAN DEALER ON SELECTING THE APPROPRIATE

VENT HOOD FOR YOUR HESTAN APPLIANCE.

CAUTION

INSTALLATION OF ANTI-TIP DEVICE

THE ANTI-TIP DEVICE PROVIDED WITH THIS RANGE

MUST BE INSTALLED.

PREPARATION

POSSIBLE PROPERTY DAMAGE - Use a qualified installer or contractor to

determine the proper method of attaching the anti-tip bracket to the rear wall

or floor behind your range. Special drills or tools may be needed to drill holes in the wall or floor

(ceramic tile, hardwood flooring, etc.).

ELECTRICAL SHOCK HAZARD - Use extreme caution when drilling holes

into the wall or floor as there may be hidden wires. Identify the electrical

circuits that could be affected by the installation of the anti-tip bracket.

Shut off the power to these circuits. Failure to follow these instructions may result in death or

electrical shock.

HOLE PREPARATION

The anti-tip bracket must be installed in sound materials, such as wood studs in the wall AND floor

joists under the finished floor. They must be able to withstand the forces exerted on the bracket by

the range should it tip-over. If wood studs or other suitable materials are not in the designated area

behind the range, you must attach the bracket using appropriate drywall anchors or similar fasteners.

DRYWALL INSTALLATION: After positioning the bracket as per the diagram below, mark the holes

and drill the appropriate holes as per the instructions supplied with the wall anchors. For hardboard

or solid plaster walls, you may need different wall anchors, available at your local hardware store or

home center.

WOOD FLOOR INSTALLATION: After positioning the bracket as per the diagram below, mark the

holes and drill the appropriate holes for #12 or similar, large wood screws, at least 1.5” [3.8 cm] in

length. Use washers as well. All hardware is available at your local hardware store or home center.

CONCRETE FLOOR INSTALLATION: After positioning the bracket as per the diagram below, mark

the holes and drill the appropriate holes for #12 or similar large masonry anchors, at least 1.5” [3.8 cm]

in length. Use washers as well. All hardware is available at your local hardware store or home center.

NOTICE

RANGE MODEL

30”, 36” 1-1/16” [2.7]

48” 3-1/4” [8.3]

INSTALLATION OF ANTI-TIP DEVICE

(CONTINUED)

ANTI-TIP BOLT ADJUSTMENT

After leveling the range, and after the bracket has been attached, adjust the anti-tip bolt and large

washer under the range so the top of the washer is 1-1/4” [3.2 cm] maximum from the floor. Slide

the range into the opening of the bracket and verify the bolt is engaged in the bracket as seen

below. Carefully tip the range forward to check. The range should not move more than 1” [2.5 cm].

ELECTRICAL CONNECTIONS

ELECTRICAL SHOCK HAZARD

Disconnect power before installing or servicing appliance. Before turning

power ON, be sure all controls are in the OFF position. Failure to do so can

result in electrical shock or death.

ELECTRICAL GROUNDING

This appliance must be grounded. Grounding reduces the risk of electric

shock in the event of a short circuit. Grounding through the neutral conductor is prohibited for

new branch circuit installations (1996 NEC), mobile homes, and recreational vehicles, or in an area

where local codes prohibit it. This range has been setup at the factory for a 4-wire connection.

CAUTION

Improper grounding will cause malfunctions in the unit, such as

continuous sparking of the igniters. This can damage the appliance and

create a shock hazard condition.

ELECTRICAL CONNECTION

The appliance may be connected using the cordset provided, or may be hard-wired. The appliance

must be on its own dedicated circuit - 240 VAC, Single Phase, 60 Hz, with a current rating as shown

in the model number listing on pg. 2. The installation must be done in accordance with local codes,

or in the absence of local codes, it must be installed in accordance with the National Electrical

Code, ANSI/NFPA 70.

For both US and CANADA installations: This appliance is equipped with

copper lead wires and must be connected to copper wires only. Improper

connection of aluminum house wiring can result in a fire or shock hazard.

Use only connectors designed and certified for connecting to aluminum

wire, and installed by a qualified electrician.

4-WIRE CONNECTION

For installations where grounding through the neutral

conductor is prohibited. Use only 4-conductor cord

kits rated 125/250 Volts (min), 50 Amps, and labeled

“For Use with Ranges”. Your Hestan range is pre-wired

at the factory for a 4-wire connection and includes this

cordset.

1. Make sure power is off at the supply panel /

breaker.

2. Remove the narrow access panel at the rear of

the range and locate the chassis ground terminal.

Attach GREEN ground appliance wire of supply

circuit or cord to chassis using ground screw.

3. Connect WHITE neutral appliance wire to WHITE

neutral wire in electrical box.

4. Connect RED (L1) appliance wire to RED power

wire in electrical box.

5. Connect BLACK (L2) appliance wire to BLACK

power wire in electrical box.

6. Tighten all connections. Strain relief must be

installed.

STRAIN RELIEF /

BRIDE DE CORDON

POWER CORD /

CORDON D’ALIMENTATION

GROUND TERMINAL /

BLOC DE MISE

À LA TERRE

3-WIRE CONNECTION

For installations where grounding through the neutral

conductor is allowed. Use only 3-conductor cord kits

rated 125/250 Volts (min), 50 Amps, and labeled “For

Use with Ranges”. This cordset is available at hardware

stores and home centers.

1. Make sure power is off at the supply panel / breaker

off.

2. Attach WHITE neutral appliance wire to WHITE

neutral wire in electrical box and use GREEN

ground jumper wire to connect to neutral as shown

here.

3. Connect RED (L1) appliance wire to RED power

wire in electrical box.

4. Connect BLACK (L2) appliance wire to BLACK

power wire in electrical box.

5. Tighten all connections. Strain relief must be

installed.

STRAIN RELIEF /

BRIDE DE CORDON

POWER CORD /

CORDON D’ALIMNENTATION

GROUND TERMINAL /

BLOC DE MISE

À LA TERRE

JUMPER WIRE /

FIL CONNECTEUR

ELECTRICAL CONNECTIONS

(CONTINUED)

GAS SUPPLY

The local gas authority or supplier should be consulted at the installation planning stage in order to

establish the availability of an adequate supply of gas (NG or LP). If it is a new installation, have the

gas authorities or supplier check the meter size and piping to assure that the unit is supplied with the

necessary amount of gas supply and pressure to operate the unit(s).

Gas connections should be made by a qualified plumber, or your professional appliance installer.

All appliances must be fitted with an accessible upstream gas shutoff valve as a means of isolating the

appliance for emergency shut off and for servicing.

Make certain new piping and connections have been made in a clean manner and have been purged

so that piping compound, chips, etc. will not clog regulators, valves, orifices, or burners. Use pipe

joint compound / thread sealant approved for natural and LP gases.

The appliance and its individual manual shutoff valve must be disconnected from the gas supply

piping system during any pressure testing of that system at test pressures in excess of 1/2 psi [3.5

kPa].

The appliance must be isolated from the gas supply piping system by closing its individual manual

shutoff valve during any pressure testing of that system at test pressures equal to or less than 1/2 psi

[3.5 kPa].

NEVER CONNECT THE APPLIANCE TO AN UNREGULATED GAS SUPPLY. Before proceeding,

ensure the appliance is fitted for Natural or Liquid Propane gas. Connecting to an improper gas type

will result in poor performance and increased risk of damage or injury. Gas type and gas consumption

(BTU per hour) for each burner type is shown on the rating label.

Installation of this cooking appliance must be made in accordance with local codes. In the absence of

local codes, this unit should be installed in accordance with the National Fuel Gas Code No.

Z223.1/

NFPA 54

, Natural Gas and Propane Installation code

CSA B149-1

, or Propane Storage and Handling

Code B149.2.

NOTE: See rating label for manifold pressure for the type of gas of your appliance.

REGULATOR LOCATION

Some range units may have the regulator mounted

internally as seen in Figure A. There is a short flex

hose which ends at a small bracket at the rear of the

range. This short flex hose has a connection end

with 1/2”NPT internal thread AND 3/4”NPT external

threads. The installer must connect a gas supply

hose at this location.

Other units have the regulator located externally

with a short flex hose and mounted to the rear of

the range with a bracket as shown in Figure B. The

regulator is shipped loose in the accessory box with

other items. The regulator must be connected to the

provided short flex hose by the installer, and then

the gas supply hose to the inlet side of the regulator.

Make a note of the flow arrow embossed on the

regulator itself. The arrow points toward the range.

The gas inlet of the regulator is 1/2”NPT thread.

Connect to the gas supply using a mininum 3/4” inside diameter (1” OD) flexible (semi-rigid) stainless

steel gas hose (not included) with appropriate fittings to prevent gas starvation. This hose should be

no more that 48” [1.2m] in length. Use the appropriate thread sealant on all connections, except flare

fittings.

The gas hose must not interfere with the rear of the range. Use caution when pushing the range

against the back wall, so that you do not kink or crimp the hose as this could result in a gas leak.

1/2”NPT

INTERNAL THREAD

FIGURE A: INTERNAL REGULATOR

3/4”NPT

EXTERNAL THREAD

GAS CONNECTION

La page charge ...

Hestan KRD364GD-NG Guide d'installation

Marque: Hestan

Modèle: KRD364GD-NG

Catégorie: Cuisinières

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Hestan KRD364GD-NG Installation guide

Documents connexes

Autres documents

Fulgor Milano F6PDF304S1 Guide d'installation