Best CP57E362SB Guide d'installation

Marque: Best

Modèle: CP57E362SB

Catégorie: Hottes

Taper: Guide d'installation

CP55IQ, CP57IQT AND CP57E SERIES

HB0132

INSTALLATION INSTRUCTIONS

INTENDED FOR DOMESTIC COOKING ONLY

INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.

HOMEOWNER: USE AND CARE INFORMATION ON PAGES 12

TO 14.

READ AND SAVE THESE INSTRUCTIONS

BEST; Hartford, Wisconsin www.BestRangeHoods.com 800-558-1711

BEST; Drummondville, QC, Canada www.BestRangeHoods.com 866-737-7770

To register your product online or for additional information visit www.BestRangeHoods.com

SV21422 rev. 03

! !

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If

you have questions, contact the manufacturer at the address or

telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel

and lock service disconnecting means to prevent power from

being switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by qualified

personnel in accordance with all applicable codes and standards,

including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of

gases through the flue (chimney) of fuel burning equipment to

prevent backdrafting. Follow the heating equipment manufacturer’s

guidelines and safety standards such as those published by the

National Fire Protection Association (NFPA) and the American

Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE) and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any solid-state speed control device.

8. To reduce the risk of fire, use only metal ductwork.

9. This unit must be grounded.

10. When applicable local regulations comprise more restrictive

installation and/or certification requirements, the aforementioned

requirements prevail on those of this document and the installer

agrees to conform to these at his own expenses.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers

cause smoking and greasy spillovers that may ignite. Heat oils

slowly on low or medium settings.

b) Always turn power pack ON when cooking at high heat or when

flambeing food (i.e.: Crêpes Suzette, Cherries Jubilee, Peppercorn

Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed to

accumulate on fan, filters or in exhaust ducts.

d) Use proper pan size. Always use cookware appropriate for the

size of the surface element.

1. For indoor use only.

2. For general ventilating use only. Do not use to exhaust hazardous

or explosive materials and vapors.

3. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

4. Your power pack motor has a thermal overload which will

automatically shut off the motor if it becomes overheated. The

motor will restart when it cools down. If the motor continues to

shut off and restart, have the power pack serviced.

5. The minimum hood distance above cooktop must not be less than

24”. A maximum of 30” above cooktop is recommended for best

capture of cooking impurities.

6. Two installers are recommended because of the large size and

weight of this unit.

7. To reduce the risk of fire and to properly exhaust air, be sure to

duct air outside — Do not exhaust air into spaces within walls or

ceiling or into attics, crawl space or garage.

8. This product is equipped with a thermostat which may start blower

automatically. To reduce the risk of injury and to prevent power

from being switched on accidentally, switch power off at service

panel and lock or tag service panel.

9. Because of the high exhausting capacity of this unit, you should

make sure enough air is entering the house to replace exhausted

air by opening a window close to or in the kitchen.

10. To reduce the risk of fire and electrical shock, the Best CP55IQ

& CP57IQT Series models should only be installed with their own

built-in blowers, and the Best CP57E Series models must only

be installed with Best exterior blower models EB6, EB9, EB12

or EB15; or Best in-line blowers models ILB3, ILB6, ILB9, ILB11.

Other blowers cannot be substituted.

11. Please read specification label on product for further information

and requirements.

12. This power pack is equipped with a RF receiver (optional remote

control sold separately). Changes or modifications not expressly

approved by the party responsible for compliance could void the

user’s authority to operate this product. The remote control has

been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules and the Canadian

ICES-003. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

The remote control generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected

WARNING

CAUTION

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE

THE FOLLOWING*:

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal

tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.

IF THE FLAMES DO NOT GO OUT IMMEDIATELY, EVACUATE

AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN — You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels — This

could cause a violent steam explosion.

4. Use an extinguisher ONLY if:

A. You own a Class ABC extinguisher and you know how to

operate it.

B. The fire is small and contained in the area where it started.

C. The fire department has been called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

WARNING

HL0207

- CP55IQ AND CP57IQT POWER PACK SYSTEMS -

MODEL 634 OR 644

(ROOF CAP)

MODEL 643

(8” ROUND WALL CAP)

ODEL 418

(10” ROUND

ADJUSTABLE ELBOW)

ODEL 410

(10” ROUND DUCT

— 2 FT. SECTIONS)

10” R

OUND VERTICAL

IN-LINE DAMPER (SUPPLIED WITH

DUAL BLOWER POWER PACK )

MODEL 437

(HIGH CAPACITY ROOF CAP)

MODEL 441

(10’’ ROUND WALL CAP)

10” R

OUND ADAPTER

(SUPPLIED WITH DUAL BLOWER

POWER PACK )

CP57IQT

POWER PACK

CP55IQ

POWER PACK

ADAPTER/DAMPER

8” ROUND (SUPPLIED WITH

SINGLE

BLOWER POWER PACK)

8” R

OUND

STANDARD

DUCT

8” ROUND

ADJUSTABLE ELBOW

INGLE INTERIOR BLOWER DUAL INTERIOR BLOWER

ACR2 REMOTE CONTROL KIT

(SOLD SEPARATELY)

HL0208

- CP57E POWER PACK SYSTEM -

MODEL 441

(10” ROUND

WALL

CAP)

MODEL 437

(HIGH CAPACITY ROOF CAP)

ODEL ILB9 (800 CFM)

OR ILB11 (1100 CFM)

IN-LINE BLOWER

(INCLUDES TWO 8” X 12” TO

10’’ ROUND TRANSITIONS)

ODEL 418

(10” ROUND

ADJUSTABLE ELBOW)—

OPTIONAL

MODEL EB6 (600 CFM)

OR EB9 (900 CFM)

EXTERIOR BLOWER

MODEL EB12 (1200 CFM)

OR EB15 (1500 CFM)

EXTERIOR BLOWER

MODEL 410

(10” ROUND DUCT

—2FT. SECTIONS)

IN-LINE AND EXTERIOR BLOWER ROUGH-IN KIT

(INCLUDED WITH EB6, EB9, EB12, EB15,

ILB3, ILB6, ILB9 AND ILB11 BLOWERS.)

CP57E

POWER PACK

MODEL ILB3 (280 CFM)

IN-LINE BLOWER

(INCLUDES ONE 8” TO 10”

ROUND TRANSITION)

MODEL ILB6 (600 CFM)

IN-LINE BLOWER

(INCLUDES TWO 4½” X 18½”

TO 10’’ ROUND TRANSITIONS)

MODEL 643

(8” ROUND

WALL

CAP)

ACR2 R

EMOTE CONTROL KIT

(SOLD SEPARATELY)

1. INSTALL DUCTWORK AND ELECTRICAL WIRING

1.1 NON-DUCTED INSTALLATION (CP55IQ SERIES POWER PACKS ONLY)

CP55IQ Series power packs may be non-ducted. ANKCP55 non-duct kit must be installed (sold separately).

1.2 DUCTED INSTALLATION (ALL POWER PACKS)

For a CP57E Series power pack, either an exterior blower or in-line blower must be used. The CP57E Series power pack must be

installed with blower models ILB3, ILB6, ILB9, ILB11, EB6, EB9, EB12 or EB15 only. Other blowers cannot be substituted (blowers

sold separately.) Plan where and how the ductwork will be installed.

If installing exterior or in-line blower, refer to instructions packed with blower and follow steps 1 up to 7, 11, 13 and up of

this manual.

Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you are installing. If installing CP55IQ Series power

pack, use 8” round ductwork and if installing CP57IQT or CP57E Series power pack, use 10” round ductwork. Use metal foil duct

tape to seal duct joints.

NOTE: It is recommended that there be a minimum of 6" of straight duct from the hood to an elbow for 8" duct and 12" for 10" duct.

1.3 ALL INSTALLATIONS

The minimum power pack distance above cooktop must not be less than 24’’. A maximum of 30” above cooktop is

recommended for best capture of cooking impurities.

Distances over 30” are at the installer and users discretion.

Run 3-wire power supply cable to installation location. Its length should extend at least 4 feet below the bottom of the custom hood.

HH0201A

POWER PACK

ROOF CAP

WALL

CAP

8” ROUND DUCT FOR CP55IQ OR

10” ROUND DUCT FOR CP57IQT

8” ROUND ADAPTER & DAMPER

FOR CP55IQ OR

10” ROUND ADAPTER FOR CP57IQT

24” TO 30”

ABOVE COOKING SURFACE

8” ROUND ELBOW FOR CP55IQ OR

10” ROUND ELBOW FOR CP57IQT

10” IN LINE

VERTICAL DAMPER FOR CP57IQT

IN-LINE BLOWER

10” ROUND DUCT

(except ILB3, 8’’ ROUND DUCT)

HH0114A

24” TO 30” ABOVE

COOKING SURFACE

ROOF CAP

WALL

CAP

POWER PACK

HH0115A

POWER PACK

EXTERIOR BLOWER

10” ROUND DUCT

24” TO 30”

ABOVE

COOKING SURFACE

10” ROUND ELBOW

EXTERIOR

BLOWER

CP55IQ (SINGLE INTERNAL BLOWER)

OR CP57IQT (DUAL INTERNAL BLOWER)

TYPICAL DUCTWORK

CP57E WITH MODEL ILB3, ILB6, ILB9

OR ILB11 IN-LINE BLOWER TYPICAL DUCTWORK

(BLOWER LOCATION IS SHOWN FOR REFERENCE ONLY)

CP57E E

XTERIOR BLOWER TYPICAL DUCTWORK

2. PREPARE INSTALLATION

WARNING

When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.

NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer.

Make sure that the following items are included:

- Power Pack

- Accessories • Hybrid baffle filters with handles (3 for 36’’ width power pack, 4 for 42’’ width power pack and 5 for 48” to 66” width power

packs)

• 8” round adapter and damper (included with CP55IQ power pack series)

• 10” round in-line vertical damper (included with CP57IQT power pack series)

• 10” round adapter (included with CP57IQT power pack series)

• Bag of parts including: 1 wire clamp, 2 wire connectors, 4 no. 8 x 3/8” screws, 9 no. 8 x 1/2” chrome plated screws,

10 no. 8-32 x 1/4” screws (not used with this product, please discard).

Parts sold separately:

• ACR2 remote control kit

• In-line blower assembly model ILB3, ILB6, ILB9 or ILB11.

• Exterior blower assembly model EB6, EB9, EB12 or EB15.

• Ducts, elbows, wall and roof caps. Refer to page 3 and 4 for a complete list of venting options and model numbers.

• Non-duct kit ANKCP55 Series, mandatory for non-ducted installation.

NOTE: During installation, protect countertop and/or cooktop.

3. CUSTOM HOOD PREPARATION

WARNING

When building a custom hood, always follow all applicable construction codes and standards.

The custom hood must be constructed to fit the size and shape of the CP55IQ, CP57IQT or the CP57E power pack.

See chart and illustration for details.

POWER PACK TOTAL

WEIGHT

POWER PACK DIMENSIONS

MODEL WIDTH A* B* C

CP55IQ

36” 52 LB.19

⁄16”34

⁄16” 4¼”

42” 62 LB.19

⁄16”40

⁄16”4

⁄8”

CP57IQT

36” 62 LB.19

⁄16”34

⁄16”5

⁄8”

36” 62 LB.22

⁄16”34

⁄16”5

⁄8”

48” 72 LB.19

⁄16”46

⁄16”5

⁄8”

48” 72 LB.22

⁄16”46

⁄16”5

⁄8”

54” 82 LB.22

⁄16”52

⁄16”5

⁄8”

60” 85 LB.22

⁄16”58

⁄16”5

⁄8”

66” 88 LB.22

⁄16”64

⁄16”5

⁄8”

CP57E

36” 40

LB.22

⁄16”34

⁄16”6”

48” 53 LB.22

⁄16”46

⁄16”6”

60” 66

LB.22

⁄16”58

⁄16”6”

7/8

”

4½”

HD0296A

12”

3”

REAR

FRONT

* Dimensions A and B include rivets head.

To minimize the gap around the power pack, take actual width and depth measurements of power pack and add 1/16” to get D and E

measurements. Cut the hole in the bottom of the cabinet according to dimensions. See chart and illustration for details.

POWER PACK CUTOUT DIMENSIONS

MODEL WIDTH DE

CP55IQ

36” 19

⁄8” 34½”

42” 19

⁄8” 40½”

CP57IQT

36” 19

⁄8” 34½”

36” 22

⁄8” 34½”

48” 19

⁄8”” 46½”

48” 22

⁄8” 46½”

54” 22

⁄8” 52½”

60” 22

⁄8” 58½”

66” 22

⁄8” 64½”

CP57E

36” 22

⁄8” 34½”

48” 22

⁄8” 46½”

60” 22

⁄8” 58½”

HD0367

4. MOUNT CUSTOM HOOD INTERNAL FRAMEWORK

5. REMOVE HYBRID BAFFLE FILTERS

Remove tape on filters. Remove filters from power pack and set aside.

It is recommended to start with the center one(s).

HH0102A

HD0521

WARNING

The wood hood must be positively secured to wall studs or other wooden framework behind the drywall. Make

sure it is capable of supporting its own weight and the weight of the CP55IQ, CP57IQT or CP57E. Failure to do so

may cause personal injury or damage to countertop or cooktop.

The CP55IQ, CP57IQT and CP57E power pack is supported by the custom hood internal framework with screws provided in parts bag.

Since the CP55IQ, CP57IQT and CP57E power pack mounting holes are located in

front and rear sides (see illustration at right), plan to install wood frame at front and

sides for support.

6. REMOVE GREASE DRIP RAIL

A. Lift grease drip rail to disengage it from the bottom

panel.

B. Slide grease rail all the way to the left or right () and

lift the opposite end to disengage the other end from

the bottom panel (). Remove it from the power pack

and set aside for later use.

7. REMOVE BOTTOM PANEL

Using a Phillips screwdriver, remove both bottom panel retaining

screws and set aside.

Disassemble bottom panel from power pack and set aside.

HO0224

RETAINING SCREW LOCATIONS

HO0120

SIDE VIEW

HD0524

HD0525





8. REMOVE KNOCK-OUT OPENING (CP55IQ AND CP57IQT SERIES ONLY)

From inside the power pack, remove the wiring box cover by removing 2 retaining screws and

set aside. Punch out the electrical knockout hole on top of the power pack. Install the wire clamp

(included in parts bag).

9. INSTALL THE 8” ADAPTER/DAMPER (CP55IQ SERIES ONLY)

Using 4 no. 8 x 3/8” screws from parts bag, assemble the adapter/damper on the top of the power

pack. To ensure proper opening of the dampers, remove shipping tape if present. Seal all joints

with metal foil duct tape to eliminate air leaks.

HR0027

HJ0016

MOUNTING SCREW LOCATIONS

10. INSTALL THE 10” ADAPTER (CP57IQT SERIES ONLY)

Using 2 no. 8 x 3/8” screws from parts bag, assemble the adapter on the top of the power pack.

Seal all joints with metal foil duct tape to eliminate air leaks.

NOTE: For a non-ducted installation, do not install the 10” in-line damper.

Install 10” in-line damper inside the vertical ductwork that will be attached to power pack. Do not

install in a horizontal ductwork or it will not open and close properly. Remove shipping tape if

present. Secure the damper to the duct with 3 no. 8 sheet metal screws (not provided). Ensure

damper opens and closes freely. Seal all joints with metal foil duct tape to eliminate air leaks.

10" min.

recommended

HJ0073A

11. INSTALL THE 10” IN-LINE DAMPER (CP57IQT AND CP57E SERIES, DUCTED INSTALLATION ONLY)

HJ0026

MOUNTING SCREW LOCATIONS

13. CONNECT WIRING (ALL BLOWERS)

Position the power pack below the installed custom hood.

WARNING

Risk of electric shock. Electrical wiring must be done by qualified personnel in accordance with all applicable

codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting

means to prevent power from being switched on accidentally.

INTERNAL BLOWERS: Insert the house wiring cable through the wire clamp

previously installed in step 8. Tighten the wire clamp to

secure the cable. Connect cable into wiring box using

wire connectors. Connect BLACK to BLACK, WHITE to

WHITE and GREEN or bare wire under GREEN ground

screw. DO NOT FORGET TO CONNECT THE GROUND.

Reinstall wiring box cover.

IN-LINE OR EXTERIOR BLOWERS: See instructions included with blower.

HE0059

Refer to the instructions included with the selected blower/rough-in kit (sold

separately) for details on installing the rough-in plate. Install the rough-in plate so

that the wiring box is located on the right side when facing the hood, as specified

on the blower housing label.

12. INSTALL THE ROUGH-IN PLATE FOR EXTERNAL BLOWER (CP57E SERIES ONLY)

HD0522

WIRING BOX

COVER

LOCK NUTS

14. INSTALL POWER PACK

CAUTION

Take care not to kink ducting when installing the power pack.

Using provided no. 8 x 1/2” chrome plated screws, install the power pack inside the

custom hood. Start with 2 screws on front corners, then use 4 screws for sides and use

the remaining screws to finalize securing the front power pack. (See figure at right for

mounting screw specific locations.)

Make sure the adapter/damper (or the adapter) enters the ducting. When there is

access to the top of the power pack, seal connections with metal foil duct tape.

HH0102A

MODEL CP55IQ ONLY: If the model CP55IQ is to be installed with a non-duct kit, install a 8” to 7” reducer (included in non-duct kit) prior

to install the power pack in its custom hood.

16. REINSTALL BOTTOM PANEL

Lift the bottom panel and engage the power pack metal tabs in

bottom panel slots, as shown in details A and B below.

Secure the bottom panel to the power pack using its screws

previously removed in step 7.

HO0224

RETAINING SCREW LOCATIONS

HO0121

SIDE VIEW

17. REINSTALL GREASE DRIP RAIL

A. Insert one end of grease rail in power pack side ()

while lifting the other end over the bottom panel

edge ().

B. Center the grease drip rail over the bottom panel

edge and flip it to snap in place.

15. PERFORM THE EXTERNAL BLOWER CONNECTIONS (CP57E SERIES ONLY)

To install the blower see instructions included with the blower.

Plug the 3-prong plug cord from rough-in plate to the 3-prong male connector

inside the power pack (A) and the 2-prong male connector cord from rough-in

plate to the 2-prong plug inside the power pack (B).

WARNING

Do not plug the two cords together.

HE0078

HD0524

HD0525





18. REINSTALL HYBRID BAFFLE FILTERS

CAUTION

Remove protective plastic film covering hybrid baffle filters before installing them.

It is recommended to install side filters first and finish with center one(s).

1. Insert one end of hybrid baffle filter into the front

channel of the power pack.

2. Raise the other end toward the inside of power

pack and insert in the grease drip rail of the

power pack.

HD0526

19. CALIBRATE IQ BLOWER SYSTEM™ (CP55IQ & CP57IQT SERIES ONLY)

NOTE: Calibration is for ducted installations only. Do not calibrate non-ducted installations.

After the power pack is installed and wired, engage the calibration process (our

Guaranteed Performance System Technology to ensure full-rated airflow is being

delivered). Prior to calibration, ensure that all filters and duct system are installed.

CALIBRATION PROCESS

Hold the calibration button for 3 seconds; calibration button will light up and stay on

for up to 13 minutes. The blower will start and begin the calibration process. When

calibration is complete, one of two things will occur:

A. The blower turns off and calibration button light turns off = Successful calibration.

B. The blower turns off and calibration button light blinks continuously = Too much

restriction in the ductwork is preventing the IQ Blower System™ from achieving the

rated airflow. The blower is automatically set to maximum intensity.

NOTE: Common items that cause restrictions: restricted damper flap (backdraft

damper, wall cap, roof cap), too many elbows, duct size less than 80% of hood

outlet, poor transition, use of flex ducting and/or crushed ducting.

Two options are available:

1. Press the calibration button to accept airflow as is. The IQ Blower System™ is now configured to its highest possible setting. The blinking

calibration light goes out.

2. Correct duct restriction and repeat the calibration process.

a. To clear the original calibration data, hold calibration button for 10 seconds. The light will blink 3 times to confirm and the blower

configuration will go back to default settings.

b. Repeat calibration process.

HC0071

CALIBRATION BUTTON

CALIBRATION LIGHT

21. USE AND CARE

Hybrid Baffle Filters

The hybrid baffle filters should be cleaned frequently. Use a warm detergent solution. Wash more often if your cooking style generates

greater grease — like frying foods or wok cooking.

Remove hybrid baffle filters by pushing them towards the back of power pack and rotating filters downward. Baffle filters are dishwasher

safe. Allow filters to dry completely before reinstalling them in the power pack.

Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of the filter may occur if using phosphate detergent

or as a result of local water conditions — but this will not affect filter performance. This discoloration is not covered by the warranty.

Grease Drip Rail

The grease drip rail should be cleaned frequently. Remove it from the power pack (see step 6 on page 7) and use a warm detergent

solution. As with the baffle filters, wash more often if your cooking style generates greater grease — like frying foods or wok cooking. Allow

grease drip rail to dry completely before reinstalling it in the power pack.

Interior Blower(s) Cleaning

Remove the filters in order to access the blower(s). Vacuum blower(s) to clean. Do not immerse in water.

Power pack cleaning

Stainless steel cleaning:

Avoid when choosing a detergent:

- Any cleaners that contain bleach will attack stainless steel.

- Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.

- Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive and should never be

used close to a range.

Do:

• Regularly wash with clean cloth or rag soaked with warm water

and mild soap or liquid dish detergent.

• Always clean in the direction of original polish lines.

• Always rinse well with clear water (2 or 3 times) after cleaning.

Wipe dry completely.

• You may also use a specialized household stainless steel

cleaner.

Don’t:

• Use any steel or stainless steel wool or any other scrapers to

remove stubborn dirt.

• Use any harsh or abrasive cleansers.

• Allow dirt to accumulate.

• Let plaster dust or any other construction residues reach the

power pack. During construction/renovation, cover the power

pack to make sure no dust sticks to stainless steel surface.

20. LIGHTING

This power pack is equipped with LED lamps which require no maintenance.

WARNING

Do not touch lamps during or soon after operation. Burns may occur.

22. OPERATION

Always turn your blower on before you begin cooking to establish an airflow in the kitchen. Let the blower run for a few minutes to clear

the air after you turn off the range.

HC0016

SPEED 1 2 3 4

BA C D E

A. BLOWER DELAY-OFF BUTTON:

When blower is on, press the delay-off button to activate the delay-off function. The corresponding speed indicator LED will start flashing to

indicate this function is activated. The fan will continue to operate for 10 minutes and will stop automatically. To cancel the delay-off function,

press the blower delay-off button once again; the blower will then work in normal mode.

NOTE: The blower speed can be increased—or decreased—during delay-off mode without starting another 10-minute cycle.

B. ON

BLOWER/SPEED CONTROL BUTTON:

Press this button to turn on the blower at the last selected speed. To change the blower speed, press the button again until the desired

speed is obtained. Press and hold this button for 2 seconds to decrease the speed level down by one increment. Possible decreases are

then: 4 to 3; 3 to 2; 2 to 1 and 1 to OFF.

NOTES: 1. Each time you press the speed control button, the speed changes by increments of 1 (e.g.: speed 1 to speed 2, to speed 3,

and then speed 4). From the fourth speed, the speed goes down to level 1.

2. The last speed used is kept in memory so that when the unit is turned on, it will return to the last setting except the fourth, the

next time the blower will be turned on, it will return to speed 3. The memorized speed level is also synced with the optional

remote control.

HEAT SENTRY™

The power pack is equipped with a protective device that activates when excessive heat is detected inside the power pack. During the Heat

Sentry activation, this device takes control of the blower and set it on speed 4; the speed 4 button LED will flash. The blower will remain

on speed 4 until the heat is back to normal, it then returns to the speed previously selected.

C. OFF

BLOWER/FILTER MAINTENANCE BUTTON:

Press this button to turn off the blower. Pressing this button also cancels the delay-off function (if activated).

NOTE: After 30 hours of operation, the 4 blower speed lights will flash 30 seconds to indicate the filters need to be cleaned in order to

maintain efficient power pack operation. Pressing this button will reset the code to indicate that maintenance has been completed.

D. OFF

LIGHTING:

Press this button to turn the lamps off.

E. ON

LIGHTING:

Press this button to turn the lamps on; all 3 control LED will light on.

NOTE: There is only one light setting.

WARNING

The HEAT SENTRY can start the blower during a range top fire or other excessive heat situations even if the power

pack is turned off. In this case, it is impossible to turn the blower OFF with blower button. If you must stop the blower

on CP55IQ/CP57IQT series models: set the main power switch located behind the baffle filters in OFF position, if

it is possible to do safely (see illustration below). For CP57E series models: do it from the main electrical panel.

A) Blower delay-off button

B) ON blower/Speed control button

C) OFF blower/

Filter maintenance button

D) OFF lighting

E) ON lighting

MAIN

POWER

SWITCH

CP55IQ AND

CP57IQT

SERIES ONLY

22. OPERATION (CONT’D)

REMOTE CONTROL:

The power pack can also be operated using the optional ACR2 remote control.

When a button is pressed on the remote control, it sends a coded signal to the receiver (factory installed on the

power pack), indicating which function to activate.

¤ : Activates/deactivates delay-off.

- : Decreases blower motor speed until turned OFF (4 to 3, 3 to 2, 2 to 1 and 1 to OFF).

+ : Turns blower motor ON and increases speed (OFF to 1, 1 to 2, 2 to 3, 3 to 4).

 : Turns ON/OFF the lamps.

1 : LED indicator (lights up blue when signal is transmitted to power pack).

NOTE: For more information, refer to the instructions included with the remote control.

Install the battery.

Before it can be used, the remote control has to be linked to the power pack following the procedure below.

INKING PROCEDURE (to a specific power pack):

1- Turn lights and blower off.

2- Press and hold the remote control

button for 3 seconds (the LED indicator lights up).

3- Press and hold power pack button A for 3 seconds to confirm link. Lighting LED indicators 1 and 3 will then blink 3 times as a completion

feedback. Linking procedure needs to be confirmed within 30 seconds, otherwise it will be cancelled.

NOTES: 1. Pressing power pack button A for 3 seconds will not enter the linking mode. The linking mode can only be activated from the

remote control

button.

2. Since the code is randomly assigned, it may be necessary to repeat the procedure in apartments or condos where many

products controlled by a remote control are close to each other.

NLINKING PROCEDURE:

1- Turn lights and blower off.

2- Press and hold power pack button E for 10 seconds. Lighting LED indicator 2 will then blink 3 times as a completion feedback.

HC0070

23. WIRING DIAGRAMS

BLDCHALL

THERMAL

PROTECTION

TRA1PRA1

WHT

LINE

NEUTRAL

GROUND

120 V AC

WHT

COLOR CODE

BLK BLACK

BLU BLUE

ORG ORANGE

RF RECEIVER

HE0168A

K1 K2 K3 K4

MOTOR

HIGH

MED HIGH

MED LOW

LOW

LAMP

LOW VAC

RED

BLK

WHT

MAIN SWITCH

WHT

BLK

BLU

ORG

NEUTRAL

SPEED 1

SPEED 2

SPEED 3

SPEED 4

AL. SWITCH

POWER CALIBRATIONRELAY INTERFACE

RED RED

WHT WHITE

YEL YELLOW

LED DRIVER

INPUT OUTPUT

LED

WHT

YEL

WARNING

Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable

codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting

means to prevent power from being switched on accidentally.

Best CP55IQ Series (single blower)

23. WIRING DIAGRAMS (CONT'D)

LINE

NEUTRAL

ROUND

120 V AC

WHT

COLOR CODE

BLK BLACK

BLU BLUE

ORG ORANGE

RF RECEIVER

HE0172A

K1 K2 K3 K4

MOTOR

IGH

MED

HIGH

MED LOW

LOW

LAMP

LOVAC

RED

BLK

WHT

MAIN SWITCH

WHT

BLK

BLU

ORG

EUTRAL

SPEED

SPEED 2

SPEED 3

SPEED 4

AL.

SWITCH

POWER CALIBRATIONRELAY INTERFACE

2CDLB1CDLBH

ALL

_1 H

ALL

WHT

MT_T

HM1

MT_THM2

BLK BLK

RED RED

WHT WHITE

YEL YELLOW

YEL

LED DRIVER

INPUT OUTPUT

LED

WHT

LED DRIVER

INPUT OUTPUT

LED

WHT

YEL

WARNING

Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable

codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting

means to prevent power from being switched on accidentally.

Best CP57IQT Series (dual blower)

23. WIRING DIAGRAMS (CONT'D)

RF RECEIVER

K1 K2 K3 K4

MOTOR

HIGH

MED HIGH

MED LOW

LOW

LAMP

LOVAC

LINE

NEUTRAL

GROUND

120 V AC

HE0169A

YEL

RED

WHT

BLK

ORG

BLU

WHT

BLU

ORG

BLK

WHT

BLU

ORG

BLK

WHT

BLU

ORG

BLK

FUSE 8 A

BLK 120

ORG 120

BLU 88

PPL 60

PNK 45

YEL 10

WHT 0

BLK 120

ORG 120

BLU 88

PPL 60

PNK 45

YEL 10

WHT 0

BLK 120

ORG 120

BLU 88

PPL 60

PNK 45

YEL 10

WHT 0

BLK

WHT

BLK

BRN

GRY

ROUGH-IN PLATE

BLK

WHT

GRN

BLK

WHT

BLK

WHT

GRN

LED DRIVER

INPUT OUTPUT

LED

COLOR CODE

BLK BLACK

BLU BLUE

BRN BROWN

GRY GREY

GRN GREEN

ORG ORANGE

PNK PINK

PPL PURPLE

RED RED

WHT WHITE

YEL YELLOW

LED DRIVER

INPUT OUTPUT

LED

YEL

BLK

WARNING

Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable

codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting

means to prevent power from being switched on accidentally.

Best CP57E Series

24. SERVICE PARTS

Best CP55IQ & CP57IQT Series

HL0211

REPLACEMENT PARTS AND REPAIRS

In order to ensure your unit remains in

good working condition, you must use

Broan-NuTone genuine replacement

parts only. Broan-NuTone genuine

replacement parts are specially

designed for each unit and are

manufactured to comply with all the

applicable certification standards and

maintain a high standard of safety.

Any third party replacement part

used may cause serious damage and

drastically reduce the performance

level of your unit, which will result

in premature failing. Broan-NuTone

recommends to contact a certified

service depot for all replacement

parts and repairs.

KEY

NO.

ART NO.DESCRIPTION

QTY. (POWER PACK WIDTH)

36" 42" 48" 54" 60" 66"

1 SV08541 ADAPTER 10” ROUND (FOR CP57IQT SERIES) 1-1111

2 SV08543 ADAPTER/DAMPER 8” ROUND (FOR CP55IQ SERIES) 11----

3 SV05869 B

EST LOGO 111111

SV17871 GREASE RAIL 36” 1-----

SV17872 GREASE RAIL 42” -1----

SV17873 GREASE RAIL 48” - - 1 - - -

SV17874 GREASE RAIL 54” - - - 1 - -

SV17875 GREASE RAIL 60” - - - - 1 -

SV17876 GREASE RAIL 66” -----1

5 SV20817 CALIBRATION BUTTON 111111

S97019432 BLDC BLOWER (FOR CP55IQ SERIES) 11----

S97019434 BLDC BLOWER (FOR CP57IQT SERIES) 2-2222

7 SV21414 LED D

RIVER AND LED LIGHT HARNESS EXTENSION 111222

8 SV21413 LED MODULE 222444

9 SV61691 F

ILTER FILLER (PAIR) -1---1

SV61639 H

YBRID BAFFLE FILTER WITH MICROMESH + HANDLE 8.84” X 8.61” X 1” 14531-

SV61640 HYBRID BAFFLE FILTER WITH MICROMESH + HANDLE 11.84” X 8.61” X 1” 2 - - 2 4 5

11 SV21411 CONTROL INTERFACE PCB FOR INTERNAL BLOWER 111111

12 SV20816 REMOTE CONTROL PCB 111111

SV21416 ELECTRONIC DRIVE (FOR CP55IQ SERIES) 11----

SV20818 ELECTRONIC DRIVE (FOR CP57IQT SERIES) 1-1111

14 SV08548 B

LACK ROCKER SWITCH 111111

* SV21418 ELECTRICAL HARNESS (FOR CP55IQ SERIES) 11----

* SV20824 ELECTRICAL HARNESS (FOR CP57IQT SERIES) 1-1111

* SV09022 TRANSFORMER 120 VAC, 9 VOLTS DC 111111

* SV08542 10” ROUND VERTICAL IN-LINE DAMPER (FOR CP57IQT SERIES) 1-1111

* SV21422 INSTALLATION GUIDE 111111

* SV08545

ARTS BAG: 2 WIRE CONNECTORS, 1 WIRE CLAMP, 4 SCREWS NO. 8 X 3/8”,

9 CHROME PLATED SCREWS NO. 8 X 1/2”, 10 MECHANICAL SCREWS NO. 8-32 X 1/4”

111111

* NOT SHOWN.

24. SERVICE PARTS (CONT'D)

Best CP57E Series

HL0212

REPLACEMENT PARTS AND REPAIRS

In order to ensure your unit remains in

good working condition, you must use

Broan-NuTone genuine replacement

parts only. Broan-NuTone genuine

replacement parts are specially

designed for each unit and are

manufactured to comply with all the

applicable certification standards and

maintain a high standard of safety.

Any third party replacement part

used may cause serious damage and

drastically reduce the performance

level of your unit, which will result

in premature failing. Broan-NuTone

recommends to contact a certified

service depot for all replacement

parts and repairs.

KEY

NO.

ART NO.DESCRIPTION

QTY. (POWER PACK WIDTH)

36" 48" 60"

1 SV05869 BEST LOGO 111

SV17871 GREASE RAIL 36” 1 - -

SV17873 GREASE RAIL 48” -1-

SV17875 G

REASE RAIL 60” --1

3 SV61659 A

UTOTRANSFORMER AND FUSE KIT (INCLUDING METAL SUPPORT) 111

4 SV21414 LED DRIVER AND LED LIGHT HARNESS EXTENSION 112

5 SV21413 LED MODULE 224

SV61639 HYBRID BAFFLE FILTER WITH MICROMESH + HANDLE 8.84” X 8.61” X 1” 1 5 1

SV61640 HYBRID BAFFLE FILTER WITH MICROMESH + HANDLE 11.84” X 8.61” X 1” 2 - 4

7 SV21412 CONTROL INTERFACE PCB FOR EXTERNAL BLOWER 111

8 SV20816 REMOTE CONTROL PCB 1 1 1

9 SV13923 FEMALE CONNECTOR 111

10 SV13924 MALE CONNECTOR 111

* SV20825 ELECTRICAL HARNESS (FOR CP57E SERIES) 111

* SV21422 I

NSTALLATION GUIDE 111

* SV08545

PARTS BAG: 2 WIRE CONNECTORS, 1 WIRE CLAMP, 4 SCREWS NO. 8 X 3/8”,

9 CHROME PLATED SCREWS NO. 8 X 1/2”, 10 MECHANICAL SCREWS NO. 8-32 X 1/4”

111

* NOT SHOWN.

25. WARRANTY

ONE-YEAR LIMITED WARRANTY

Broan-NuTone LLC (“Broan-NuTone”) warrants to the original consumer purchaser of its products that such products will be free

from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE.

During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be

defective under normal use and service.

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES AND BULBS, FUSES, FILTERS, DUCTS,

ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and

service or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other

than by Broan-NuTone), faulty installation or installation contrary to recommended installation instructions.

The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states or provinces

do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE’S OPTION, SHALL BE THE PURCHASER’S

SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL,

CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE.

Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to another.

Any modification performed on this product without the authorization of Broan-NuTone will void this warranty. This warranty supersedes

all prior warranties.

To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone number stated below, (b) give the model

number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service,

you must present evidence of the original purchase date.

Best

, 926 W. State Street, Hartford, WI 53027 (1-800-637-1453)

Best

, 550 Lemire Blvd., Drummondville, QC, Canada (1-866-737-7770)

www.bestrangehoods.com

La page charge ...

Best CP57E362SB Guide d'installation

Marque: Best

Modèle: CP57E362SB

Catégorie: Hottes

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Best CP57E362SB Installation guide
español: Best CP57E362SB Guía de instalación

Best CP57E362SB Guide d'installation

Best CP57E362SB Guide d'installation

dans d''autres langues

Documents connexes