Simplicity 09P70B-0273-H5 Manuel utilisateur
- Catégorie
- Accessoires pour véhicules automobiles
- Taper
- Manuel utilisateur
Ce manuel convient également à
Not for
Reproduction
Copyright © Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
80084670
Revision: A
Not for
Reproduction
3
11
12
13
14
15
16
17
18
Not for
Reproduction
5
Copyright © Briggs & Stratton Corporation, Milwaukee, WI, USA. All rights reserved.
This manual contains safety information to make you aware of the hazards and risks
associated with engines and how to avoid them. It also contains instructions for the
proper use and care of the engine. Because Briggs & Stratton Corporation does not
necessarily know what equipment this engine will power, it is important that you read
and understand these instructions and the instructions for the equipment.Save these
original instructions for future reference.
Note:The figures and illustrations in this manual are provided for reference only and
may differ from your specific model. Contact your dealer if you have questions.
For replacement parts or technical assistance, record below the engine model, type,
and code numbers along with the date of purchase. These numbers are located on your
engine (see theFeatures and Controlssection).
Date of Purchase
Engine Model - Type - Trim
Engine Serial Number
Recycling Information
Recycle all packaging, used oil, and batteries according to
applicable government regulations.
Operator Safety
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS for future use.
Safety Alert Symbol and Signal Words
The safety alert symbol ( ) is used to identify safety information about hazards that
can result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used
with the alert symbol to indicate the likelihood and the potential severity of injury. In
addition, a hazard symbol may be used to represent the type of hazard.
DANGERindicates a hazard which, if not avoided,will result in death or
serious injury.
WARNINGindicates a hazard which, if not avoided,could result in death or
serious injury.
CAUTIONindicates a hazard which, if not avoided,could result in minor or
moderate injury.
NOTICEindicates a situation thatcould result in damage to the product.
Hazard Symbols and Meanings
Safety information about
hazards that can result in
personal injury.
Read and understand the
Operator's Manual before
operating or servicing the
unit.
Fire hazard Explosion hazard
Shock hazard Toxic fume hazard
Hot surface hazard Noise hazard - Ear protection
recommended for extended
use.
Thrown object hazard -
Wear eye protection.
Explosion hazard
Frostbite hazard Kickback hazard
Amputation hazard -
moving parts
Chemical hazard
Thermal heat hazard Corrosive
Safety Messages
WARNING
This product can expose you to chemicals including gasoline engine exhaust, which
is known to the State of California to cause cancer, and carbon monoxide, which is
known to the State of California to cause birth defects or other reproductive harm. For
more information go to www.P65Warnings.ca.gov.
WARNING
Briggs & Stratton® Engines are not designed for and are not to be used to power:
fun-karts; go-karts; children's, recreational, or sport all-terrain vehicles (ATVs);
motorbikes; hovercraft; aircraft products; or vehicles used in competitive events not
sanctioned by Briggs & Stratton. For information about competitive racing products,
see www.briggsracing.com. For use with utility and side-by-side ATVs, please contact
Briggs & Stratton Power Application Center, 1-866-927-3349. Improper engine
application may result in serious injury or death.
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Adding Fuel
• Turn engine off and let engine cool at least 2 minutes before removing the fuel
cap.
• Fill fuel tank outdoors or in well-ventilated area.
• Do not overfill fuel tank. To allow for expansion of the fuel, do not fill above the
bottom of the fuel tank neck.
• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if
necessary.
• If fuel spills, wait until it evaporates before starting engine.
When Starting Engine
• Make sure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in
place and secured.
• Do not crank engine with spark plug removed.
• If engine floods, set choke (if equipped) to OPEN / RUN position, move throttle (if
equipped) to FAST position and crank until engine starts.
When Operating Equipment
• Do not tip engine or equipment at angle which causes fuel to spill.
• Do not choke the carburetor to stop engine.
• Never start or run the engine with the air cleaner assembly (if equipped) or the air
filter (if equipped) removed.
When Changing Oil
• If you drain the oil from the top oil fill tube, the fuel tank must be empty or fuel can
leak out and result in a fire or explosion.
When Tipping Unit for Maintenance
Not for
Reproduction
6 BRIGGSandSTRATTON.com
• When performing maintenance that requires the unit to be tipped, the fuel tank, if
mounted on the engine, must be empty or fuel can leak out and result in a fire or
explosion.
When Transporting Equipment
• Transport with fuel tank EMPTY or with fuel shut-off valve in the CLOSED
position.
When Storing Fuel Or Equipment With Fuel In Tank
• Store away from furnaces, stoves, water heaters or other appliances that have
pilot lights or other ignition sources because they can ignite fuel vapors.
WARNING
Starting engine creates sparking.
Sparking can ignite nearby flammable gases.
Explosion and fire could result.
• If there is natural or LP gas leakage in area, do not start engine.
• Do not use pressurized starting fluids because vapors are flammable.
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. You CANNOT see it, smell it, or
taste it. Even if you do not smell exhaust fumes, you could still be exposed
to carbon monoxide gas. If you start to feel sick, dizzy, or weak while using
this product, get to fresh air RIGHT AWAY. See a doctor. You may have carbon
monoxide poisoning.
• Operate this product ONLY outside far away from windows, doors and vents to
reduce the risk of carbon monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide
alarms with battery back-up according to the manufacturer's instructions. Smoke
alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages, basements, crawlspaces,
sheds, or other partially-enclosed spaces even if using fans or opening doors and
windows for ventilation. Carbon monoxide can quickly build up in these spaces
and can linger for hours, even after this product has shut off.
• ALWAYS place this product downwind and point the engine exhaust away from
occupied spaces.
WARNING
Rotating parts can contact or entangle hands, feet, hair, clothing, or
accessories.
Traumatic amputation or severe laceration can result.
• Operate equipment with guards in place.
• Keep hands and feet away from rotating parts.
• Tie up long hair and remove jewelry.
• Do not wear loose-fitting clothing, dangling drawstrings or items that could become
caught.
WARNING
Running engines produce heat. Engine parts, especially muffler, become
extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch fire.
• Allow muffler, engine cylinder and fins to cool before touching.
• Remove accumulated debris from muffler area and cylinder area.
• It is a violation of California Public Resource Code, Section 4442, to use or
operate the engine on any forest-covered, brush-covered, or grass-covered land
unless the exhaust system is equipped with a spark arrester, as defined in Section
4442, maintained in effective working order. Other states or federal jurisdictions
may have similar laws. Contact the original equipment manufacturer, retailer, or
dealer to obtain a spark arrester designed for the exhaust system installed on this
engine.
WARNING
Unintentional sparking can result in fire or electric shock.
Unintentional start-up can result in entanglement, traumatic amputation, or
laceration.
Fire hazard
Before performing adjustments or repairs:
• Disconnect the spark plug wire and keep it away from the spark plug.
• Models with portable battery pack:Remove battery pack from engine battery
tray. Battery pack may represent equipment key in some instances.
• Models with integrated battery pack:Disconnect wire harness from starter
motor.
• Use only correct tools.
• Do not tamper with governor spring, links or other parts to increase engine speed.
• Replacement parts must be of the same design and installed in the same position
as the original parts. Other parts may not perform as well, may damage the unit,
and may result in injury.
• Do not strike the flywheel with a hammer or hard object because the flywheel may
later shatter during operation.
When testing for spark:
• Use approved spark plug tester.
• Do not check for spark with spark plug removed.
WARNING
Improper use of the battery and charger can result in an electrical shock or
fire.
When Operating
• Keep the battery charger dry. Avoid exposing the battery pack to rain or wet
conditions.
• To reduce the risk of electrical shock, do not allow water to flow into AC plug.
• Do not short circuit; never place any object into the battery contacts.
When Charging The Battery Pack
• Charge the Briggs and Stratton battery pack only with the Briggs and Stratton
battery charger.
• Do not use the Briggs and Stratton battery charger to charge any other types of
batteries.
• Keep the battery charger dry. Avoid exposing the battery pack to rain or wet
conditions.
• To reduce risk of damage to the electric plug and cord, pull by the plug rather than
the cord when disconnecting the charger.
• Do not operate the charger with a damaged plug or cord. The supply cord cannot
be replaced. If the cord is damaged, the charger should be replaced immediately.
• Do not operate the charger if it has received a sharp blow, been dropped, or
otherwise damaged in any way. If the charger is damaged it must be replaced.
The charger is not serviceable.
• Do not disassemble or attempt to service the charger.
• To reduce risk of electric shock, unplug the charger from outlet before cleaning.
• Do not short circuit; never place any object into the battery contacts.
• The charger is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Children should be supervised to make sure that they do not play with the
charger.
Extension Cord
• An extension cord should not be used unless absolutely necessary. Use of
improper extension cord could result in a risk of fire and electric shock. If an
extension cord must be used, make sure:
1. That the pins on the plug of the extension cord are the same number, size,
and shape as those of the plug on the charger;
2. That the extension cord is properly wired and in good electrical condition;
and
3. That the wire size is a minimum of 16 AWG to allow for AC ampere rating of
the charger.
When Storing Battery Pack
• Keep the battery charger dry. Avoid exposing the battery pack to rain or wet
conditions.
Before Performing Adjustments Or Repairs
Not for
Reproduction
7
• Models with portable battery pack:Remove the battery pack from the engine
battery tray.
• Models with integrated battery pack:Disconnect the wire harness from the
starter motor.
WARNING
Battery chemicals are toxic and corrosive.
Fire or explosion can cause severe burns or death.
• Never burn or incinerate discarded or used battery packs as they may explode.
Toxic fumes and materials are created when battery packs are burned.
• Do not use a battery that has been crushed, dropped, or damaged.
Features and Controls
Engine Controls
Compare the illustration (Figure:1,2,3) with your engine to familiarize yourself with the
location of various features and controls.
A. Engine Identification NumbersModel - Type - Code
B. Spark Plug
C. Muffler, Muffler Guard (if equipped), Spark Arrester (if equipped)
D. Electric Starter
E. Dipstick
F. Lithium-Ion Portable Battery Pack
G. Air Intake Grille
H. Fuel Tank and Cap
I. Air Cleaner
J. Throttle Control (if equipped)
K. Battery Charger - Portable Battery Pack
L. Fuel Shut-off (if equipped)
M. Lithium-Ion Integrated Battery Pack
N. Cable and Charger - Integrated Battery Pack
Engine Control Symbols and Meanings
Engine speed - FAST Engine speed - SLOW
Engine speed - STOP ON - OFF
Engine start - Choke
CLOSED
Engine start - Choke OPEN
Fuel Cap
Fuel Shut-off - OPEN
Fuel Shut-off - CLOSED
Fuel level - Maximum
Do not overfill
Battery Control Symbols and Meanings
Volt Ampere
Double Insulated Alternating Current
Direct Current Underwriters Laboratories,
Inc. US & Canada Listed
Product
Underwriters Laboratories,
Inc. Registered Product
Hertz
Properly Recycle Battery
Charge Battery Pack
Remove Key / Battery Pack
Operation
Oil Recommendations
Oil Capacity:See theSpecificationssection.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers
or dealers may have added oil to the engine. Before you start the engine for the first
time, make sure to check the oil level and add oil as specified by the instructions in
this manual. If you start the engine without oil, it will be damaged beyond repair and
will not be covered under warranty.
We recommend the use of Briggs & Stratton
®
Warranty Certified oils for best
performance. Other high-quality detergent oils are permitted if classified for service SF,
SG, SH, SJ or higher. Do not use special additives.
Outdoor temperatures determine the correct oil viscosity for the engine. Use the chart
to select the best viscosity for the outdoor temperature range expected. Engines on
most outdoor power equipment operate well with 5W-30 Synthetic oil. For equipment
operated in hot temperatures, Vanguard
®
15W-50 Synthetic oil gives the best
protection.
Not for
Reproduction
8 BRIGGSandSTRATTON.com
A SAE 30 -Below 40 °F (4 °C) the use of SAE 30 will result in hard starting.
B 10W-30 -Above 80 °F (27 °C) the use of 10W-30 may cause increased oil
consumption. Checkthe oil level frequently.
C 5W-30
D Synthetic 5W-30
E
Vanguard
®
Synthetic 15W-50
Check and Add Oil
See Figure: 4
Before checking or adding oil
• Make sure the engine is level.
• Clean the oil fill area of any debris.
• See the Specifications section for oil capacity.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers
or dealers may have added oil to the engine. Before you start the engine for the first
time, make sure to check the oil level and add oil according to the instructions in this
manual. If you start the engine without oil, it will be damaged beyond repair and will
not be covered under warranty.
Check Oil Level
1. Remove the dipstick (A, Figure 4) and wipe with a clean cloth.
2. Install and tighten the dipstick (A, Figure 4).
3. Remove the dipstick and check the oil level. Correct oil level is at the top of the full
indicator (B, Figure 4) on the dipstick.
Add Oil
1. If the oil level is low, slowly add oil into the engine oil fill (C, Figure 4). Do not
overfill. After adding oil, wait one minute and then check the oil level.
2. Reinstall and tighten the dipstick (A, Figure 4).
Fuel Recommendations
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.
• Gasoline with up to 10% ethanol (gasohol) is acceptable.
NOTICE Do not use unapproved gasolines, such as E15 and E85. Do not mix oil in
gasoline or modify the engine to run on alternate fuels. Use of unapproved fuels will
damage the engine components, which will not be covered under warranty.
To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel.
SeeStorage.All fuel is not the same. If starting or performance problems occur,
change fuel providers or change brands. This engine is certified to operate on gasoline.
The emissions control system for this engine is EM (Engine Modifications).
High Altitude
At altitudes over 5,000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON)
gasoline is acceptable.
For carbureted engines, high altitude adjustment is required to maintain performance.
Operation without this adjustment will cause decreased performance, increased fuel
consumption, and increased emissions. Contact a Briggs & Stratton Authorized Service
Dealer for high altitude adjustment information. Operation of the engine at altitudes
below 2,500 feet (762 meters) with the high altitude adjustment is not recommended.
For Electronic Fuel Injection (EFI) engines, no high altitude adjustment is necessary.
Add Fuel
See Figure: 5
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When adding fuel
• Turn engine off and let engine cool at least 2 minutes before removing the fuel
cap.
• Fill fuel tank outdoors or in well-ventilated area.
• Do not overfill fuel tank. To allow for expansion of the fuel, do not fill above the
bottom of the fuel tank neck.
• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if
necessary.
• If fuel spills, wait until it evaporates before starting engine.
1. Clean the fuel cap area of dirt and debris. Remove the fuel cap.
2. Fill the fuel tank (A, Figure 5) with fuel. To allow for expansion of the fuel, do not
fill above the bottom of the fuel tank neck (B). Some models have a fuel level
indicator (C). Do not fill the tank above the bottom of the fuel level indicator (D).
3. Reinstall the fuel cap.
Charge The Battery Pack
See Figure :6789
WARNING
Improper use of the battery or the charger can result in an electrical shock or
fire.
When Charging Battery Pack
• Charge the Briggs & Stratton battery pack only with the Briggs & Stratton battery
charger.
• Do not use the Briggs & Stratton battery charger to charge any other types of
batteries.
• Keep the battery charger dry. Avoid exposing the battery pack to rain or wet
conditions.
• To reduce risk of damage to the electric plug and cord, pull by the plug rather than
the cord when disconnecting the charger.
• An extension cord should not be used unless absolutely necessary. Use of
improper extension cord could result in a risk of fire and electric shock. If an
extension cord must be used, make sure:
1. That the pins on the plug of the extension cord are the same number, size,
and shape as those of the plug on the charger;
2. That the extension cord is properly wired and in good electrical condition;
and
3. That the wire size is a minimum of 16 AWG to allow for AC ampere rating of
the charger.
• Do not operate the charger with a damaged plug or cord. The supply cord cannot
be replaced. If the cord is damaged, the charger should be replaced immediately.
• Do not operate the charger if it has received a sharp blow, been dropped, or
otherwise damaged in any way. If the charger is damaged it must be replaced.
The charger is not serviceable.
• Do not disassemble the charger; or attempt to service.
• To reduce risk of electric shock, unplug the charger from outlet before cleaning.
• Do not short circuit; never place any object into the battery contacts.
• The charger is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Children should be supervised to make sure that they do not play with the
charger.
When To Charge The Battery Pack
First Time Portable Battery Pack- The Lithium‐Ion portable battery pack was partially
charged before shipment. To maintain charge and to prevent damage while in storage,
the battery pack is programed to enter a “sleep mode”. A quick charge of approximately
ten (10) seconds is required to wake up the battery. Leave battery pack in charger
until fully charged. To charge the battery pack, see theHow To Charge The Battery
Packsection below.
As Required- To check available charge, push the Battery Fuel Gauge button (E,
Figure67) and charge if required. See theBattery Fuel Gaugesection.
How To Charge The Battery Pack
WARNING
Keep the battery charger dry. Avoid exposing the battery pack to rain or wet
conditions.
1. Connect the battery charger (F, Figure89) to an electrical outlet.
2. Portable Battery Pack:Slide the battery pack (G, Figure8) firmly into the battery
charging bay (F). If the red charging light does not illuminate, remove the battery
Not for
Reproduction
9
pack and reinstall. Make sure the battery pack is firmly seated in the battery
charging bay.
• Red light (A, Figure6) indicates the battery pack is charging normally.
• Green light (B) indicates the battery pack is fully charged.
• Red light (C) flashes indicates that the battery pack is either too hot or
too cold and will not accept a charge. Leave the battery pack connected
and when normal operating temperature is reached it will automatically
start charging. See theSpecificationssection for normal operating
temperature.
• Red/green lights (D) flashes indicate that the battery pack will not charge
and must be replaced.
3. Portable Battery Pack:From “sleep mode”, the battery will wake up in
approximately ten (10) seconds.
4. Portable Battery Pack:A completely discharged battery pack will fully charge in
approximately one (1) hour. The battery pack will stay fully charged if left on the
charger.
5. Portable Battery Pack:When the green light indicates that the battery pack is
fully charged, remove the battery pack from the charger.
6. Integrated Battery Pack:Connect the charger plug (G, Figure9) to the engine.
7. Integrated Battery Pack:A completely discharged battery pack will fully charge in
approximately four (4) hours.
8. Integrated Battery Pack:When the green light indicates that the battery pack is
fully charged, remove from the charger.
9. To check available charge, push the Battery Fuel Gauge button (E, Figure67).
10. When not in use, disconnect the battery charger from the electrical outlet.
Battery Fuel Gauge
To check available charge, push the Battery Fuel Gauge button (E, Figure67). The
display lights (H) will indicate the approximate amount of available charge remaining in
the battery pack.
Display Lights Available Charge
Four lights 75% to 100%
Three lights 50% to 75%
Two lights 25% to 50%
One light 10% to 25%
Light flashes Low
Integrated Battery Pack:When connected to the charger, if all display lights are off
then the battery is fully charged. Disconnect the charger.
Start and Stop Engine
See Figure:10,11,12,13
Start Engine
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Starting Engine
• Make surethat spark plug, muffler, fuel cap and air cleaner (if equipped) are in
place and secured.
• Do not crank engine with spark plug removed.
• If engine floods, set choke (if equipped) to OPEN or RUN position, move throttle (if
equipped) to FAST position and crank until engine starts.
WARNING
Improper use of battery and charger can result in an electrical shock or fire.
When Operating
• Keep battery charger dry. Avoid exposing battery pack to rain or wet conditions.
• To reduce the risk of electrical shock, do not allow water to flow into AC plug.
• Do not short circuit; never place any object into the battery contacts.
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. You CANNOT see it, smell it, or
taste it. Even if you do not smell exhaust fumes, you could still be exposed to
carbon monoxide gas. If you start to feel sick, dizzy, or weak while using this
product, shut it off and get to fresh air RIGHT AWAY. See a doctor. You may
have carbon monoxide poisoning.
• Operate this product ONLY outside far away from windows, doors and vents to
reduce the risk of carbon monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide
alarms with battery back-up according to the manufacturer's instructions. Smoke
alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages, basements, crawlspaces,
sheds, or other partially-enclosed spaces even if using fans or opening doors and
windows for ventilation. Carbon monoxide can quickly build up in these spaces
and can linger for hours, even after this product has shut off.
• ALWAYS place this product downwind and point the engine exhaust away from
occupied spaces.
NOTICE This engine was shipped from Briggs & Stratton without oil. Before you
start the engine, make sure you add oil according to the instructions in this manual.
If you start the engine without oil, it will be damaged beyond repair and will not be
covered under warranty.
Note:Equipment may have remote controls. See the equipment manual for location and
operation of remote controls.
1. Check the engine oil. See theCheck Oil Levelsection.
2. Modelswithportable battery pack:Mount the battery pack (A, Figure10) in
the engine battery tray on top of the engine. Make sure battery pack is securely
installed. Battery pack may represent equipment key in some instances.
Note:Modelswithportable battery pack:To wake up a new battery, aFirst
Timequick charge of approximately ten (10) seconds is required. See theWhen To
Charge Battery Packsection.
3. Make sure equipment drive controls, if equipped, are disengaged.
4. Move the fuel shut-off (D, Figure11), if equipped, to the OPEN position.
5. Move the throttle control (B, Figure11), if equipped, to the FAST position. Operate
the engine in the FAST position.
6. Modelswithelectric start switch:Hold the engine stop lever (C, Figure12)
against the handle. Move the electric start switch to the START position. See the
equipment manual for the location and operation of the electric start switch.
7. Modelswithoutelectric start switch:Hold the engine stop lever (C, Figure12)
against the handle. Engine will automatically start. See the equipment manual for
operation of the engine stop lever.
NOTICE To extend the life of the starter, use short starting cycles (five seconds
maximum). Wait one minute between starting cycles.
Modelswithportable battery pack:If the engine will not crank and the battery pack
display lights are flashing, then the battery pack temperature is too hot or current draw is
too high. All four battery display lights (H, Figure13) will flash a warning for 10 seconds.
The battery pack does not have a fuse, but will automatically reset after 10 seconds. If
battery pack temperature is too hot (over 140 F, 60 C), remove the battery and allow it
to cool. To avoid excess current draw on lawnmowers, keep the mower housing clean of
grass build-up and debris.
Note:If the engine does not start after repeated attempts, contact a local dealer or go
toBRIGGSandSTRATTON.comor call1-800-233-3723(in USA).
Stop Engine
1. Engine Stop Lever:Release the engine stop lever (E, Figure12).
Throttle Control, if equipped with stop feature:Move the throttle control (B,
Figure11) to the STOP position.
Electric Start Switch, if equipped:Move the electric start switch to the OFF /
STOP position. See the equipment manual for the location and operation of the
switch. Remove the key and keep in a safe place out of the reach of children.
2. After the engine stops, move the fuel shut-off (D, Figure11), if equipped, to the
CLOSED position.
3. Modelswithportable battery pack:Remove the battery pack. The battery pack
may represent equipment key in some instances.
Maintenance
Not for
Reproduction
10 BRIGGSandSTRATTON.com
NOTICE If the engine is tipped during maintenance, the fuel tank, if mounted on
engine, must be empty and the spark plug side must be up. If the fuel tank is not
empty and if the engine is tipped in any other direction, it may be difficult to start due
to oil or gasoline contaminating the air filter and/or the spark plug.
WARNING
When performing maintenance that requires the unit to be tipped, the fuel tank, if
mounted on the engine, must be empty or fuel can leak out and result in a fire or
explosion.
We recommend that you see any Briggs & Stratton Authorized Dealer for all
maintenance and service of the engine and engine parts.
NOTICE All the components used to build this engine must remain in place for
proper operation.
WARNING
Unintentional sparking can result in fire or electric shock.
Unintentional start-up can result in entanglement, traumatic amputation, or
laceration.
Fire hazard
Before performing adjustments or repairs:
• Disconnect the spark plug wire and keep it away from the spark plug.
• Models with portable battery pack:Remove the battery pack from the engine
battery tray. The battery pack may represent equipment key in some instances.
• Models with integrated battery pack:Disconnect the wire harness from the
starter motor.
• Use only correct tools.
• Do not tamper with governor spring, links or other parts to increase engine speed.
• Replacement parts must be of the same design and installed in the same position
as the original parts. Other parts may not perform as well, may damage the unit,
and may result in injury.
• Do not strike the flywheel with a hammer or hard object because the flywheel may
later shatter during operation.
When testing for spark:
• Use approved spark plug tester.
• Do not check for spark with spark plug removed.
Emissions Control Service
Maintenance, replacement, or repair of the emissions control devices and
systems may be performed by any off-road engine repair establishment or
individual. However, to obtain "no charge" emissions control service, the work must be
performed by a factory authorized dealer. See the Emissions Control Statements.
Maintenance Schedule
First 5 Hours
• Change oil (Not required on Just Check & Add™ models)
Every 8 Hours or Daily
• Check engine oil level
• Clean area around muffler and controls
• Clean air intake grille
Every 25 Hours or Annually
•
Clean air filter
1
• Clean pre-cleaner (if equipped)
Every 50 Hours or Annually
• Change engine oil (Not required on Just Check & Add™ models)
• Service exhaust system
Annually
• Replace spark plug
• Replace air filter
• Replace pre-cleaner (if equipped)
•
Service cooling system
1
•
Check valve clearance
2
1
In dusty conditions or when airborne debris is present, clean more often.
2
Not required unless engine performance problems are noted.
Carburetor and Engine Speed
Never make adjustments to the carburetor or engine speed. The carburetor was set at
the factory to operate efficiently under most conditions. Do not tamper with the governor
spring, linkages, or other parts to change the engine speed. If any adjustments are
required contact a Briggs & Stratton Authorized Service Dealer for service.
NOTICE The equipment manufacturer specifies the maximum speed for the engine
as installed on the equipment.Do not exceedthis speed. If you are not sure what the
equipment maximum speed is, or what the engine speed is set to from the factory,
contact a Briggs & Stratton Authorized Service Dealer for assistance. For safe and
proper operation of the equipment, the engine speed should be adjusted only by a
qualified service technician.
Service Spark Plug
See Figure:14
Check the gap (A, Figure14) with a wire gauge (B). If necessary, reset the gap. Install
and tighten the spark plug to the recommended torque. For gap setting or torque, see
theSpecificationssection.
Note:In some areas, local law requires using a resistor spark plug to suppress ignition
signals. If this engine was originally equipped with a resistor spark plug, use the same
type for replacement.
Service Exhaust System
WARNING
Running engines produce heat. Engine parts, especially muffler, become
extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch fire.
• Allow muffler, engine cylinder and fins to cool before touching.
• Remove accumulated debris from muffler area and cylinder area.
• It is a violation of California Public Resource Code, Section 4442, to use or
operate the engine on any forest-covered, brush-covered, or grass-covered land
unless the exhaust system is equipped with a spark arrester, as defined in Section
4442, maintained in effective working order. Other states or federal jurisdictions
may have similar laws. Contact the original equipment manufacturer, retailer, or
dealer to obtain a spark arrester designed for the exhaust system installed on this
engine.
Remove accumulated debris from muffler and cylinder area. Inspect the muffler for
cracks, corrosion, or other damage. Remove the deflector or the spark arrester, if
equipped, and inspect for damage or carbon blockage. If damage is found, install
replacement parts before operating.
WARNING
Replacement parts must be of the same design and installed in the same position
as the original parts. Other parts may not perform as well, may damage the unit, and
may result in injury.
Change Engine Oil
See Figure:15,16,17,18
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
Running engines produce heat. Engine parts, especially muffler, become
extremely hot.
Severe thermal burns can occur on contact.
• When you drain the oil from the top oil fill tube, the fuel tank must be empty or fuel
can leak out and result in a fire or explosion.
• Allow muffler, engine cylinder and fins to cool before touching.
Check and add oil as required. See theCheck Oil Levelsection. An oil change is not
required but if you desire to change the oil follow the procedure below.
Not for
Reproduction
11
Used oil is a hazardous waste product and must be disposed of properly. Do not discard
with household waste. Check with your local authorities, service center, or dealer for
safe disposal/recycling facilities.
Remove Oil
The oil must be drained from the top oil fill tube.
1. With engine off but still warm, disconnect the spark plug wire (D, Figure15) and
keep it away from the spark plug (E).
2. Models with integrated battery:Disconnect the wire harness (F, Figure16) from
the electric starter.
3. Remove the dipstick (A, Figure17).
4. When you drain the oil from the top oil fill tube (C, Figure18), keep the spark plug
(E) end of the engine up. Drain the oil into an approved container.
WARNING
When you drain the oil from the top oil fill tube, the fuel tank must be empty or fuel
can leak out and result in a fire or explosion. To empty the fuel tank, run the engine
until it stops from lack of fuel.
Add Oil
• Make sure the engine is level.
• Clean the oil fill area of any debris.
• See the Specifications section for oil capacity.
1. Remove the dipstick (A, Figure 17) and wipe with a clean cloth.
2. Slowly pour oil into the engine oil fill (C, Figure 17). Do not overfill. After adding
oil, wait one minute and then check the oil level.
3. Install and tighten the dipstick (A, Figure 17).
4. Remove the dipstick and check the oil level. Correct oil level is at the top of the full
indicator (B, Figure 17) on the dipstick.
5. Reinstall and tighten the dipstick (A, Figure 17).
6. Connect the spark plug wire (D, Figure 15) to the spark plug (E).
Service Air Filter
See Figure: 19
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
• Never start and run the engine with the air cleaner assembly (if equipped) or the
air filter (if equipped) removed.
NOTICE Do not use pressurized air or solvents to clean the filter. Pressurized air
can damage the filter and solvents will dissolve the filter.
See the Maintenance Schedule for service requirements.
Paper Air Filter
1. Open the cover (B, Figure 19).
2. Remove the filter (C, Figure 19).
3. Remove the pre-cleaner (E, Figure 19), if equipped, from the filter. To loosen
debris, gently tap the filter on a hard surface. If the filter is excessively dirty,
replace with a new filter.
4. Wash the pre-cleaner in liquid detergent and water. Then allow it to thoroughly air
dry. Do not oil the pre-cleaner.
5. Assemble the dry pre-cleaner, if equipped, to the filter.
6. Install the filter (C, Figure 19).
7. Close the cover (B, Figure 19).
Service Cooling System
WARNING
Running engines produce heat. Engine parts, especially muffler, become
extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc., can catch fire.
• Allow muffler, engine cylinder and fins to cool before touching.
• Remove accumulated debris from muffler area and cylinder area.
NOTICE Do not use water to clean the engine. Water could contaminate the fuel
system. Use a brush or dry cloth to clean the engine.
This is an air cooled engine. Dirt or debris can restrict air flow and cause the engine to
overheat, resulting in poor performance and reduced engine life.
1. Use a brush or dry cloth to remove debris from the air intake grille.
2. Keep linkage, springs and controls clean.
3. Keep the area around and behind the muffler, if equipped, free of any combustible
debris.
4. Make sure the oil cooler fins, if equipped, are free of dirt and debris.
After a period of time, debris can accumulate in the cylinder cooling fins and cause the
engine to overheat. This debris cannot be removed without partial disassembly of the
engine. Have a Briggs & Stratton Authorized Service Dealer inspect and clean the air
cooling system as recommended in the Maintenance Schedule.
Lithium-Ion Battery Pack Disposal
WARNING
Battery chemicals are toxic and corrosive.
Fire or explosion can cause severe burns or death.
Electrical Shock
• Never burn or incinerate discarded or used battery packs as they may explode.
Toxic fumes and materials are created when battery packs are burned.
• Do not use a battery that has been crushed, dropped, or damaged.
Used and discarded battery packs will likely still carry a small electrical charge and
should be handled with care. Always dispose of discarded or used battery packs
according to federal, state and local regulations.
RBRC (Rechargeable Battery Recycling Corporation) Seal
RBRC is a non-profit public service organization dedicated to recycling
used rechargeable batteries. To find a battery collection site near
you, call toll free 1-800-8-BATTERY or 1-877-2-RECYCLE. For more
information and a listing of Recycling Locations, visit RBRC online at
www.call2recycle.org.
Storage
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
Electrical Shock
When Storing Fuel Or Equipment With Fuel In Tank
• Store away from furnaces, stoves, water heaters or other appliances that have
pilot lights or other ignition sources because they can ignite fuel vapors.
When Storing Battery Pack
• Keep battery charger dry. Avoid exposing battery pack to rain or wet conditions.
Fuel System
See Figure:20,21
Note:Some models have a fuel tank for vertical storage that will let the engine tilt for
maintenance or storage (C, Figure20). Do not store in vertical position with fuel tank
filled above the bottom of the fuel level indicator (D), if equipped. For further instructions,
see the equipment manual.
Store the engine level (normal operating position). Fill fuel tank (A, Figure21) with fuel.
To allow for expansion of fuel, do not overfill above the fuel tank neck (B).
Fuel can become stale when kept in a storage container for more than 30 days. Each
time you fill the container with fuel, addSTA-BIL 360°
®
PROTECTION™to the fuel as
specified by the manufacturer’s instructions. This keeps fuel fresh and decreases fuel-
related problems or contamination in the fuel system.
It is not necessary to drain fuel from the engine whenSTA-BIL
360°
®
PROTECTION™is added as instructed. Before storage, turn the engine ON for 2
minutes to move the fuel and stabilizer through the fuel system.
Not for
Reproduction
12 BRIGGSandSTRATTON.com
Engine Oil
While the engine is still warm, change the engine oil. See the Change Oil section. For
Just Check & Add™ models, an oil change is not required.
Battery Pack and Charger
See Figure:2223
Portable battery pack:When not in use, disconnect charger and store in a cool, dry
area. Wet, damp areas can cause corrosion of terminals and electrical contacts. If stored
for long periods in high temperatures (120° F / 49° C), permanent damage to the battery
pack can result. Check electrical terminals and contacts on battery packs and charger.
Wipe with clean cloth or blow clean with compressed air.
After storage, a normal charge may be required. To check available charge, press the
Battery Fuel Gauge button (E, Figure2223) and charge if required. See theBattery
Fuel Gaugesection.
Troubleshooting
For assistance, contact your local dealer or go to BRIGGSandSTRATTON.com or call
1-800-233-3723 (in USA).
Specifications
Model:090000
Displacement 8.64ci (140cc)
Bore 2.495in (63,4mm)
Stroke 1.75in (44,45mm)
Oil Capacity 15oz (,44L)
Spark Plug Gap .020in (,51mm)
Spark Plug Torque 180lb-in (20Nm)
Armature Air Gap .006 - .014in (,15 - ,36mm)
Intake Valve Clearance .004 - .008in (,10 - ,20mm)
Exhaust Valve Clearance .004 - .008in (,10 - ,20mm)
Model:093J00
Displacement 9.15ci (150cc)
Bore 2.583in (65,60mm)
Stroke 1.75in (44,45mm)
Oil Capacity 15oz (,44L)
Spark Plug Gap .020in (,51mm)
Spark Plug Torque 180lb-in (20Nm)
Armature Air Gap .006 - .014in (,15 - ,36mm)
Intake Valve Clearance .004 - .008in (,10 - ,20mm)
Exhaust Valve Clearance .004 - .008in (,10 - ,20mm)
Model:100000
Displacement 9.93ci (163cc)
Bore 2.668in (68,28mm)
Stroke 1.75in (44,45mm)
Oil Capacity 15oz (,44L)
Spark Plug Gap .030in (,76mm)
Spark Plug Torque 180lb-in (20Nm)
Armature Air Gap .006 - .014in (,15 - ,36mm)
Intake Valve Clearance .004 - .008in (,10 - ,20mm)
Exhaust Valve Clearance .004 - .008in (,10 - ,20mm)
Lithium-Ion Battery (Portable)
Lithium-Ion Battery Pack 10.8V (10,8V)
Charge Minutes 60
Charging Current 2AMP (2AMP)
Charger AC Input (Variable) 100 - 240V
Operating Temperature 32 - 113° F (0 - 45° C)
Lithium-Ion Battery (Integrated)
Lithium-Ion Battery Pack 10.8V (10,8V)
Charge Minutes 240
Charging Current .5AMP (.5AMP)
Charger AC Input (Variable) 100 - 240V
Operating Temperature 32 - 104° F (0 - 44° C)
Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and
1% for each 10° F (5.6° C) above 77° F (25° C). The engine will operate satisfactorily
at an angle up to 15°. Refer to the equipment operator's manual for safe allowable
operating limits on slopes.
Service Parts - Models:090000,093J00,100000
Service Part Part Number
Air Filter (see Figure19) 593260
Air Filter, Pre-cleaner (see Figure19) 594055
Oil - SAE 30 100005
Resistor Spark Plug (Model090000,093J00) 692051
Resistor Spark Plug (Model100000) 594056
Spark Plug Wrench 19576
Spark Tester 19368
Portable Lithium-Ion Battery Pack (US / Canada) 593559
Portable Lithium-Ion Battery Pack (EU / UK / AU) 593560
Portable Lithium-Ion Battery Charger (US / Canada) 593561
Portable Lithium-Ion Battery Charger (EU) 593562
Portable Lithium-Ion Battery Charger (UK) 593576
Portable Lithium-Ion Battery Charger (AU) 594501
Integrated Lithium-Ion Battery Pack 84002154
IntegratedLithium-Ion Battery Charger(US / Canada) 84002790
IntegratedLithium-Ion Battery Charger(UK) 84002791
IntegratedLithium-Ion Battery Charger(EU) 84002792
IntegratedLithium-Ion Battery Charger(AU) 84002793
We recommend that you see any Briggs & Stratton Authorized Dealer for all
maintenance and service of the engine and engine parts.
Power Ratings:The gross power rating for individual gasoline engine models is
labeled in accordance with SAE (Society of Automotive Engineers) code J1940 Small
Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995.
Torque values are derived at 2600 RPM for those engines with “rpm” called out on the
label and 3060 RPM for all others; horsepower values are derived at 3600 RPM. The
gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power
values are taken with exhaust and air cleaner installed whereas gross power values
are collected without these attachments. Actual gross engine power will be higher than
net engine power and is affected by, among other things, ambient operating conditions
and engine-to-engine variability. Given the wide array of products on which engines
are placed, the gasoline engine may not develop the rated gross power when used in a
given piece of power equipment. This difference is due to a variety of factors including,
but not limited to, the variety of engine components (air cleaner, exhaust, charging,
cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions
(temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing
and capacity limitations, Briggs & Stratton may substitute an engine of higher rated
power for this engine.
Warranty
Briggs & Stratton Engine Warranty
Effective January 2019
Limited Warranty
Briggs & Stratton warrants that, during the warranty period specified below, it will repair
or replace, free of charge, any part that is defective in material or workmanship or
both. Transportation charges on product submitted for repair or replacement under this
warranty must be borne by purchaser. This warranty is effective for and is subject to
the time periods and conditions stated below. For warranty service, find the nearest
Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM.
The purchaser must contact the Authorized Service Dealer, and then make the product
available to the Authorized Service Dealer for inspection and testing.
Not for
Reproduction
13
There is no other express warranty. Implied warranties, including those of
merchantability and fitness for a particular purpose, are limited to the warranty
period listed below, or to the extent permitted by law.Liability for incidental or
consequential damages are excluded to the extent exclusion is permitted by law. Some
states or countries do not allow limitations on how long an implied warranty lasts,
and some states or countries do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation and exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state and country to country
4
.
Standard Warranty Terms
1, 2, 3
Vanguard®; Commercial Series
3
Consumer Use - 36 months
Commercial Use - 36 months
XR Series
Consumer Use - 24 months
Commercial Use - 24 months
All Other Engines Featuring Dura-Bore™ Cast Iron Sleeve
Consumer Use - 24 months
Commercial Use - 12 months
All Other Engines
Consumer Use - 24 months
Commercial Use - 3 months
1
These are our standard warranty terms, but occasionally there may
be additional warranty coverage that was not determined at time of
publication. For a listing of current warranty terms for your engine, go to
BRIGGSandSTRATTON.com or contact your Briggs & Stratton Authorized Service
Dealer.
2
There is no warranty for engines on equipment used for prime power in place
of a utility; standby generators used for commercial purposes, utility vehicles
exceeding 25 MPH, or engines used in competitive racing or on commercial or
rental tracks.
3
Vanguard installed on standby generators: 24 months consumer use, no
warranty commercial use. Commercial Series with manufacturing date before July
2017: 24 months consumer use, 24 months commercial use.
4
In Australia - Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.
For warranty service, find the nearest Authorized Service Dealer in our dealer
locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by
emailing or writing to [email protected], Briggs & Stratton
Australia Pty Ltd, 1 Moorebank Avenue, Moorebank, NSW , Australia, 2170.
The warranty period begins on the original date of purchase by the first retail or
commercial consumer. "Consumer use" means personal residential household use by a
retail consumer. "Commercial use" means all other uses, including use for commercial,
income producing or rental purposes. Once an engine has experienced commercial
use, it shall thereafter be considered as a commercial use engine for purposes of this
warranty.
Save your proof of purchase receipt. If you do not provide proof of the initial
purchase date at the time warranty service is requested, the manufacturing date
of the product will be used to determine the warranty period. Product registration
is not required to obtain warranty service on Briggs & Stratton products.
About Your Warranty
This limited warranty covers engine-related material and/or workmanship issues only,
and not replacement or refund of the equipment to which the engine may be mounted.
Routine maintenance, tune-ups, adjustments, or normal wear and tear are not covered
under this warranty. Similarly, warranty is not applicable if the engine has been altered
or modified or if the engine serial number has been defaced or removed. This warranty
does not cover engine damage or performance problems caused by:
1. The use of parts that are not original Briggs & Stratton parts;
2. Operating the engine with insufficient, contaminated, or an incorrect grade of
lubricating oil;
3. The use of contaminated or stale fuel, gasoline formulated with ethanol greater
than 10%, or the use of alternative fuels such as liquefied petroleum or natural gas
on engines not originally designed/manufactured by Briggs & Stratton to operate
on such fuels;
4. Dirt which entered the engine because of improper air cleaner maintenance or re-
assembly;
5. Striking an object with the cutter blade of a rotary lawn mower, loose or improperly
installed blade adapters, impellers, or other crankshaft coupled devices, or
excessive v-belt tightness;
6. Associated parts or assemblies such as clutches, transmissions, equipment
controls, etc., which are not supplied by Briggs & Stratton;
7. Overheating due to grass clippings, dirt and debris, or rodent nests which plug or
clog the cooling fins or flywheel area, or by operating the engine without sufficient
ventilation;
8. Excessive vibration due to over-speeding, loose engine mounting, loose or
unbalanced cutter blades or impellers, or improper coupling of equipment
components to the crankshaft;
9. Misuse, lack of routine maintenance, shipping, handling, or warehousing of
equipment, or improper engine installation.
Warranty service is available only through Briggs & Stratton Authorized Service
Dealers. Locate your nearest Authorized Service Dealer in our dealer locator map
at BRIGGSandSTRATTON.COM or by calling 1-800-233-3723 (in USA).
80004537 (Rev. F)
Briggs & Stratton Emissions Warranty
California, U.S. EPA, and Briggs & Stratton Corporation Emissions Control
Warranty - Your Warranty Rights and Obligations
For Briggs & Stratton Engine Models with "B" or "G" Trim Designation (Model-
Type-Trim Representation xxxxxx xxxx Bx or xxxxxx xxxx Gx)
The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are
pleased to explain the exhaust emissions (“emissions”) control system warranty on
your 2019-2021 engine. In California, new small off-road engines and large spark
ignited engines less than or equal to 1.0 liter must be designed, built, and equipped
to meet the State’s stringent anti-smog standards. B&S must warrant the emissions
control system on your engine for the periods of time listed below provided there has
been no abuse, neglect or improper maintenance of your small off-road engine or
equipment leading to the failure of the emissions control system.
Your emissions control system may include parts such as the carburetor or fuel-
injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid
fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated
components. Also included may be hoses, belts, connectors, and other emission-
related assemblies.
Where a warrantable condition exists, B&S will repair your engine at no cost to you
including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
The exhaust emissions control system on your engine is warranted for two years.
If any emissions-related part on your engine is defective, the part will be repaired or
replaced by B&S.
Owner’s Warranty Responsibilities:
• As the engine owner, you are responsible for the performance of the required
maintenance listed in your owner’s manual. B&S recommends that you retain
all receipts covering maintenance on your engine, but B&S cannot deny
warranty coverage solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
• As the engine owner, you should however be aware that B&S may deny you
warranty coverage if your engine or a part has failed due to abuse, neglect, or
improper maintenance or unapproved modifications.
• You are responsible for presenting your engine to a B&S distribution center
or service center as soon as the problem exists. The warranty repairs shall be
completed in a reasonable amount of time, not to exceed 30 days. If you have a
question regarding your warranty rights and responsibilities, you should contact
B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.COM.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty
Coverage. It is in addition to the B&S engine warranty for non-regulated engines found
in the Operator’s Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed below (the
emissions control systems parts) to the extent these parts were present on the
B&S engine.
a. Fuel Metering System
• Cold start enrichment system (soft choke)
• Carburetor or fuel injection system
• Oxygen sensor
• Electronic control unit
• Fuel pump module
b. Air Induction System
• Air cleaner
• Intake manifold
c. Ignition System
Not for
Reproduction
14 BRIGGSandSTRATTON.com
• Spark plug(s)
• Magneto ignition system
d. Catalyst System
• Catalytic converter
• Exhaust manifold
• Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
• Vacuum, temperature, position, time sensitive valves and switches
• Connectors and assemblies
• Electronic controls
2. Length of Coverage
Coverage is for a period of two years from the date of delivery to an ultimate
purchaser, or for the time period listed in the respective engine or product
warranty statement, whichever is greater. B&S warrants to the original purchaser
and each subsequent purchaser that the engine is designed, built, and equipped
so as to conform with all applicable regulations adopted by the Air Resources
Board; that it is free from defects in material and workmanship that could cause
the failure of a warranted part; and that it is identical in allmaterial respects to the
engine described in the manufacturer’s application for certification. The warranty
period begins on the date the engine or equipment is delivered to an ultimate
purchaser.
The warranty on emissions-related parts is as follows:
• Any warranted part that is not scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the
warranty period stated above. If any such part fails during the period of
warranty coverage, the part will be repaired or replaced by B&S at no
charge to the owner. Any such part repaired or replaced under the warranty
will be warranted for the remaining warranty period.
• Any warranted part that is scheduled only for regular inspection in the
Operator’s Manual supplied, is warranted for the warranty period stated
above. Any such part repaired or replaced under warranty will be warranted
for the remaining warranty period.
• Any warranted part that is scheduled for replacement as required
maintenance in the Operators’s Manual supplied, is warranted for the
period of time prior to the first scheduled replacement point for that part.
If the part fails prior to the first scheduled replacement, the part will be
repaired or replaced by B&S at no charge to the owner. Any such part
repaired or replaced under warranty will be warranted for the remainder of
the period prior to the first scheduled replacement point for the part.
• Add-on or modified parts that are not exempted by the Air Resources
Board may not be used. The use of any non-exempted add-on or modified
parts by the owner will be grounds for disallowing a warranty claim. The
manufacturer will not be liable to warrant failures of warranted parts caused
by the use of a non-exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the
failure of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine
warranty policy. Warranty coverage does not apply to failures of emissions
parts that are not original equipment B&S parts or to parts that fail due to abuse,
neglect, or improper maintenance as set forth in the B&S engine warranty policy.
B&S is not liable for warranty coverage of failures of emissions parts caused by
the use of add-on or modified parts.
Look For Relevant Emissions Durability Period and Air Index Information On
Your Small Off-Road Engine Emissions Label
Engines that are certified to meet the California Air Resources Board (CARB) small off-
road Emissions Standard must display information regarding the Emissions Durability
Period and the Air Index. Briggs & Stratton makes this information available to the
consumer on our emissions labels. The engine emissions label will indicate certification
information.
TheEmissions Durability Perioddescribes the number of hours of actual running
time for which the engine is certified to be emissions compliant, assuming proper
maintenance in accordance with the Operator’s Manual. The following categories are
used:
Moderate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
50 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 125 hours of actual engine running time.
Intermediate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
125 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 250 hours of actual engine running time.
Extended:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
300 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 500 hours of actual engine running time.
For example, a typical walk-behind lawn mower is used 20 to 25 hours per year.
Therefore, theEmissions Durability Periodof an engine with anintermediaterating
would equate to 10 to 12 years.
Briggs & Stratton engines are certified to meet the United States Environmental
Protection Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions
Compliance Period referred to on the Emissions Compliance label indicates the
number of operating hours for which the engine has been shown to meet Federal
emissions requirements.
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
80084161_A
Briggs & Stratton Emissions Warranty
California, U.S. EPA, and Briggs & Stratton Corporation Emissions Control
Warranty - Your Warranty Rights and Obligations
For Briggs & Stratton Engine Models with "F" Trim Designation (Model-Type-
Trim Representation xxxxxx xxxx Fx)
The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are
pleased to explain the exhaust and evaporative emissions (“emissions”) control system
warranty on your 2019-2021 engine/equipment. In California, new equipment that
use small off-road engines must be designed, built, and equipped to meet the State’s
stringent anti-smog standards. B&S must warrant the emissions control system on
your engine/equipment for the periods of time listed below provided there has been no
abuse, neglect or improper maintenance of your small off-road engine or equipment
leading to the failure of the emissions control system.
Your emissions control system may include parts such as the carburetor or fuel-
injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid
fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated
components. Also included may be hoses, belts, connectors, and other emission-
related assemblies.
Where a warrantable condition exists, B&S will repair your engine/equipment at no cost
to you including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
The exhaust and evaporative emissions control system on your engine/equipment is
warranted for two years. If any emissions-related part on your engine/equipment is
defective, the part will be repaired or replaced by B&S.
Owner’s Warranty Responsibilities:
• As the engine/equipment owner, you are responsible for the performance of the
required maintenance listed in your owner’s manual. B&S recommends that you
retain all receipts covering maintenance on your engine/equipment, but B&S
cannot deny warranty coverage solely for the lack of receipts or for your failure to
ensure the performance of all scheduled maintenance.
• As the engine/equipment owner, you should however be aware that B&S may
deny you warranty coverage if your engine/equipment or a part has failed due to
abuse, neglect, or improper maintenance or unapproved modifications.
• You are responsible for presenting your engine/equipment to a B&S distribution
center or service center as soon as the problem exists. The warranty repairs shall
be completed in a reasonable amount of time, not to exceed 30 days. If you have
a question regarding your warranty rights and responsibilities you should contact
B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.COM.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty
Coverage. It is in addition to the B&S engine warranty for non-regulated engines found
in the Operator’s Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed below (the
emissions control systems parts) to the extent these parts were present on the
B&S engine and/or B&S supplied fuel system.
a. Fuel Metering System
• Cold start enrichment system (soft choke)
• Carburetor or fuel injection system
Not for
Reproduction
15
• Oxygen sensor
• Electronic control unit
• Fuel pump module
• Fuel line (for liquid fuel and fuel vapors), fuel line fittings, clamps
• Fuel tank, cap and tether
• Carbon canister and mounting bracket
• Pressure relief valves
• Liquid/Vapor separator
b. Air Induction System
• Air cleaner
• Intake manifold
• Purge and vent line
c. Ignition System
• Spark plug(s)
• Magneto ignition system
d. Catalyst System
• Catalytic converter
• Exhaust manifold
• Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
• Vacuum, temperature, position, time sensitive valves and switches
• Connectors and assemblies
• Electronic controls
2. Length of Coverage
Coverage is for a period of two years from the date of delivery to an ultimate
purchaser, or for the time period listed in the respective engine or product
warranty statement, whichever is greater. B&S warrants to the original purchaser
and each subsequent purchaser that the engine is designed, built, and equipped
so as to conform with all applicable regulations adopted by the Air Resources
Board; that it is free from defects in material and workmanship that could cause
the failure of a warranted part; and that it is identical in all material respects to the
engine described in the manufacturer’s application for certification. The warranty
period begins on the date the engine or equipment is delivered to an ultimate
purchaser.
The warranty on emissions-related parts is as follows:
• Any warranted part that is not scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the
warranty period stated above. If any such part fails during the period of
warranty coverage, the part will be repaired or replaced by B&S at no
charge to the owner. Any such part repaired or replaced under the warranty
will be warranted for the remaining warranty period.
• Any warranted part that is scheduled only for regular inspection in the
Operator’s Manual supplied, is warranted for the warranty period stated
above. Any such part repaired or replaced under warranty will be warranted
for the remaining warranty period.
• Any warranted part that is scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the period
of time prior to the first scheduled replacement point for that part. If the
part fails prior to the first scheduled replacement, the part will be repaired
or replaced by B&S at no charge to the owner. Any such part repaired or
replaced under warranty will be warranted for the remainder of the period
prior to the first scheduled replacement point for the part.
• Add-on or modified parts that are not exempted by the Air Resources
Board may not be used. The use of any non-exempted add-on or modified
parts by the owner will be grounds for disallowing a warranty claim. The
manufacturer will not be liable to warrant failures of warranted parts caused
by the use of a non-exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the
failure of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine
warranty policy. Warranty coverage does not apply to failures of emissions
parts that are not original equipment B&S parts or to parts that fail due to abuse,
neglect, or improper maintenance as set forth in the B&S engine warranty policy.
B&S is not liable for warranty coverage of failures of emissions parts caused by
the use of add-on or modified parts.
Look For Relevant Emissions Durability Period and Air Index Information On
Your Small Off-Road Engine Emissions Label
Engines that are certified to meet the California Air Resources Board (CARB) small off-
road Emissions Standard must display information regarding the Emissions Durability
Period and the Air Index. Briggs & Stratton makes this information available to the
consumer on our emissions labels. The engine emissions label will indicate certification
information.
TheEmissions Durability Perioddescribes the number of hours of actual running
time for which the engine is certified to be emissions compliant, assuming proper
maintenance in accordance with the Operator’s Manual. The following categories are
used:
Moderate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
50 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 125 hours of actual engine running time.
Intermediate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
125 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 250 hours of actual engine running time.
Extended:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
300 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 500 hours of actual engine running time.
For example, a typical walk-behind lawn mower is used 20 to 25 hours per year.
Therefore, theEmissions Durability Periodof an engine with anintermediaterating
would equate to 10 to 12 years.
Briggs & Stratton engines are certified to meet the United States Environmental
Protection Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions
Compliance Period referred to on the Emissions Compliance label indicates the
number of operating hours for which the engine has been shown to meet Federal
emissions requirements.
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
80084158_A
Not for
Reproduction
16 BRIGGSandSTRATTON.com
Copyright © Briggs & Stratton Corporation, Milwaukee, WI, EE.UU. Todos los derechos
reservados.
Este manual contiene información de seguridad para que usted tome conciencia
de los peligros y riesgos asociados con los motores, y cómo evitarlos. También
contiene instrucciones para el uso y cuidado apropiados del motor. Ya que
Briggs&StrattonCorporation no conoce necesariamente el equipo donde se usará este
motor, es importante que usted lea y entienda estas instrucciones y las instrucciones
del equipo.Conserve estas instrucciones originales para futuras consultas.
Nota:Las figuras e ilustraciones de este manual solo se proporcionan como referencia
y pueden diferir de su modelo específico. Comuníquese con su distribuidor si tiene
preguntas.
Para conseguir repuestos o asistencia técnica, registre a continuación los números
de modelo, tipo y código de su motor junto con la fecha de compra. Estos números se
encuentran localizados en su motor (consulte la secciónCaracterísticas y controles).
Fecha de compra
Modelo del motor - Tipo - Reglaje
Número de Serie del motor
Información de reciclaje
Todos los envases, el aceite usado y las baterías
deben reciclarse de acuerdo con las regulaciones
gubernamentales aplicables.
Seguridad del operador
INSTRUCCIONES DE SEGURIDAD
IMPORTANTES
GUARDE ESTAS INSTRUCCIONES para usarlas en un futuro.
Símbolo de alerta de seguridad y
palabras de señalización
El símbolo de aviso de seguridad ( ) se usa para identificar información de seguridad
acerca de los riesgos que pueden producir lesiones corporales. Se señaliza con una
palabra (PELIGRO, ADVERTENCIA o PRECAUCIÓN) con el símbolo de aviso para
indicar la probabilidad de una lesión y su potencial gravedad. Además, se puede usar
un símbolo de peligro para representar el tipo de riesgo.
PELIGROindica un riesgo que, si no se evita,ocasionará la muerte o lesiones
graves.
ADVERTENCIAindica un riesgo que, si no se evita,podría ocasionar la muerte
o lesiones graves.
PRECAUCIÓNindica un riesgo que, si no se evita,podría ocasionar lesiones
leves o moderadas.
AVISO indica una situación que podría provocar daños al producto.
Símbolos de peligro y significados
Información de seguridad
sobre peligros que pueden
conllevar a lesiones
personales.
Lea y entienda el Manual del
Operario antes de operar y
realizar mantenimientos a la
unidad.
Peligro de incendio Peligro de explosión
Peligro de descarga
eléctrica
Peligro de vapores tóxicos
Peligro de superficie
caliente
Peligro de ruido: Protección
auditiva recomendada para
uso extendido.
Peligro de elemento
lanzado: utilizar protección
para los ojos.
Peligro de explosión
Peligro de congelación Peligro de retroceso
Peligro de amputación:
piezas móviles
Peligro químico
Peligro de calor térmico Corrosivo
Mensajes de seguridad
ADVERTENCIA
Este producto puede exponerlo a sustancias químicas, entre las que se incluyen
emisiones de escape de motor de gasolina, reconocidas por el Estado de California
como causantes de cáncer, y monóxido de carbono, reconocido por el Estado
de California como causante de defectos de nacimiento u otros problemas
reproductivos. Para obtener más información, visite www.P65Warnings.ca.gov.
ADVERTENCIA
Los motores Briggs & Stratton® no están diseñados para y no deben utilizarse
para impulsar "karts" recreativos o deportivos; vehículos recreativos para niños
o deportivos todo terreno; motos; aerodeslizadores; productos de aeronaves o
vehículos utilizados en eventos competitivos no sancionados por Briggs & Stratton.
Para obtener información sobre productos para carreras competitivas, vaya a
www.briggsracing.com. Para uso con vehículos utilitarios y side-by-side todo terreno,
contáctese con el Centro de Aplicación de Potencia de Motores Briggs & Stratton
al 1-866-927-3349. El uso del motor para aplicaciones inadecuadas puede generar
lesiones graves o la muerte.
ADVERTENCIA
El combustible y sus vapores son extremamente inflamables y explosivos.
El fuego o la explosión pueden causar quemaduras graves o la muerte.
Cuando agregue combustible
• Apague el motor y deje que se enfríe por lo menos 2 minutos antes de remover la
tapa del combustible.
• Llene el tanque de combustible en exteriores o en un área bien ventilada.
• No llene excesivamente el tanque de combustible. Para permitir la expansión del
combustible, no llene el tanque por arriba de la parte inferior del cuello.
• Mantenga el combustible alejado de chispas, llamas abiertas, testigos piloto,
fuentes de calor y otras fuentes de encendido.
• Compruebe con frecuencia si existen grietas o fugas en las mangueras de
combustible, el tanque, la tapa y los accesorios. Reemplace las piezas, si es
necesario.
• Si se derramó combustible, espere hasta que se haya evaporado antes arrancar
el motor.
Cuando encienda el motor
• Asegúrese de que la bujía, el silenciador, la tapa del combustible y el filtro de aire
(si está equipado) estén colocados y fijos en su lugar.
• No haga girar el motor si retiró la bujía.
• Si el motor se ahoga, coloque el estrangulador (si está equipado) en la posición
de apertura/funcionamiento (OPEN/RUN), coloque el acelerador (si está
equipado) en la posición de velocidad (FAST) y arranque el motor hasta que se
encienda.
Cuando opere el equipo
Not for
Reproduction
17
• No incline el motor ni el equipo de forma que pueda derramarse el combustible.
• No estrangule el carburador para detener el motor.
• Nunca encienda o haga funcionar el motor sin el conjunto del purificador de aire
(si tiene) o el filtro de aire (si tiene).
Cuando cambie el aceite
• Si drena el aceite desde el tubo superior de llenado de aceite, el tanque de
combustible debe estar vacío o de lo contrario podría presentarse una fuga de
combustible que podría ocasionar un incendio o una explosión.
Cuando incline la unidad para trabajos de mantenimiento
• Al realizar trabajos de mantenimiento que requieran inclinar la unidad, el tanque
de combustible, si está montado en el motor, debe estar vacío o podría haber una
fuga de combustible y generar un incendio o una explosión.
Cuando transporte el equipo
• Transporte con el tanque de combustible VACÍO o con la válvula de cierre de
combustible en la posición CLOSED.
Cuando almacene el combustible o el equipo con combustible en el tanque
• Almacene lejos de hornos, estufas, calentadores de agua u otros aparatos
que utilicen testigos piloto u otras fuentes de encendido ya que estos pueden
encender los vapores combustibles.
ADVERTENCIA
Dar arranque al motor crea chispeo.
El chispeo puede encender los gases inflamables cercanos.
podría ocasionar una explosión o un incendio.
• Si hay una fuga de gas natural o gas propano LP en el área, no le de arranque al
motor.
• No use líquidos de arranque presurizados ya que los vapores son inflamables.
ADVERTENCIA
PELIGRO DE GAS TÓXICO. La descarga de escape del motor contiene
monóxido de carbono, un gas tóxico que puede matar en minutos. NO puede
verlo, es inodoro e insípido. Incluso si no huele los gases del escape, puede
estar expuesto al monóxido de carbono. Si comienza a sentirse mareado o
débil cuando utiliza el producto, tome aire fresco INMEDIATAMENTE . consulte
a un médico, Puede haberse intoxicado con monóxido de carbono.
• Opere este producto SOLAMENTE al aire libre, lejos de ventanas, puertas y
ventilaciones, para reducir el riesgo de que el monóxido de carbono se acumule y
pueda circular a espacios habitados.
• Instale alarmas de monóxido de carbono con baterías o enchufe (batería de
respaldo) siguiendo las instrucciones del fabricante. Las alarmas de humo no
pueden detectar el monóxido de carbono.
• NO opere este producto dentro de hogares, garajes, sótanos, espacios reducidos,
cobertizos u otros espacios parcialmente cerrados, incluso si usa ventiladores o
deja las puertas y ventanas abiertas. El monóxido de carbono se puede acumular
rápidamente en estos espacios y puede permanecer durante horas, incluso
después de que se apaga este producto.
• SIEMPRE coloque este producto en la dirección del viento y apunte el escape del
motor lejos de espacios habitados.
ADVERTENCIA
Las piezas giratorias pueden tener contacto o atrapar las manos, los pies, el
cabello, la ropa o los accesorios.
podría ocasionar una amputación traumática o una laceración grave.
• Opere el equipo con los protectores en su lugar.
• Mantenga las manos y los pies a distancia de las partes rotantes.
• Recoja el pelo largo y quítese cualquier joya.
• No use ropa floja, tiras que cuelguen o artículos que puedan ser agarrados.
ADVERTENCIA
El funcionamiento de los motores produce calor. Las piezas de los motores,
especialmente el silenciador, se calientan demasiado.
Pueden ocurrir graves quemaduras al tocarlas.
Los desechos combustibles, tal como hojas, grama, maleza, etc. pueden
prenderse fuego.
• Deje que el silenciador, el cilindro y las aletas del motor se enfríen antes de
tocarlos.
• Extraiga los desechos acumulados en el área del silenciador y en el área del
cilindro.
• Es una violación del Código de Recursos Públicos de California, Sección 4442,
utilizar u operar el motor en cualquier espacio con árboles, maleza o grama a
menos que el sistema de escape esté equipado con un extintor de chispas, como
lo define la Sección 4442, mantenido en correcto funcionamiento. Otros estados o
jurisdicciones federales pueden tener leyes similares. Póngase en contacto con el
vendedor, el distribuidor o el fabricante del equipo original para obtener un extintor
de chispas diseñado para el sistema de escape instalado en este motor.
ADVERTENCIA
Cualquier chispa generada involuntariamente podría causar incendio o
descarga eléctrica.
Cualquier arranque involuntariamente podría causar enredo, amputacione
traumática o laceracione.
Peligro de incendio
Antes de realizar ajustes o reparaciones:
• Desconecte el cable de la bujía y manténgalo lejos de la bujía.
• Modeloscon paquete de batería portátil:Retire el paquete de batería de la
bandeja de baterías del motor. En algunos casos, es posible que el paquete de
batería represente la llave del equipo.
• Modelos con paquete de batería integrado:Desconecte el arnés de cables del
motor de arranque.
• Use solamente las herramientas correctas.
• No manipule el resorte del regulador, las conexiones u otras piezas para
aumentar la velocidad del motor.
• Las piezas de repuesto deben ser del mismo diseño y deben ser instaladas en la
misma posición que las piezas originales. Otras piezas pueden no funcionar de la
misma manera, pueden dañar la unidad y pueden causar lesiones.
• No golpee el volante con un martillo o un objeto duro, ya que el volante puede
eventualmente romperse durante la operación.
Al probar si hay chispas:
• Use un probador de bujías aprobado.
• No revise si hay chispas con la bujía removida.
ADVERTENCIA
El uso inadecuado de la batería y del cargador puede provocar una descarga
eléctrica o un incendio.
Cuando opere el equipo
• Mantenga seco el cargador de batería. Evite exponer el paquete de baterías a la
lluvia o a condiciones de humedad.
• Para reducir el riesgo de una descarga eléctrica, no permita que ingrese agua en
el enchufe de CA.
• No provoque un cortocircuito; no coloque objetos en los contactos de la batería.
Al cargar el paquete de batería
• Cargue el paquete de batería Briggs & Stratton solo con el cargador de batería
Briggs & Stratton.
• No use el cargador de batería Briggs & Stratton para cargar otro tipo de baterías.
• Mantenga seco el cargador de batería. Evite exponer el paquete de baterías a la
lluvia o a condiciones de humedad.
• Para reducir el riesgo de daño al enchufe y el cable, tire del enchufe y no del
cable al desconectar el cargador.
• No opere el cargador con un enchufe o cable dañado. El cabe alimentador
no puede reemplazarse. Si el cable está dañado, el cargador deberá ser
reemplazado de inmediato.
• No opere el cargador si ha recibido un golpe seco, ha sufrido una caída, u otro
tipo de daño. Si el cargador está dañado, debe reemplazarse. El cargador no es
reparable.
• No desmonte ni intente reparar el cargador.
Not for
Reproduction
18 BRIGGSandSTRATTON.com
• Para reducir el riesgo de descarga eléctrica, desconecte el cargador del
tomacorriente antes de limpiarlo.
• No provoque un cortocircuito; no coloque objetos en los contactos de la batería.
• El cargador no está diseñado para el uso de personas (incluidos niños) con
capacidades físicas, sensoriales o mentales reducidas, sin experiencia y
conocimiento, a menos que se les esté proporcionando supervisión o instrucción
respecto al uso del aparato por parte de una persona responsable de su
seguridad.
• Los niños deben estar supervisados para asegurarse de que no jueguen con el
cargador.
Cable de extensión
• Un cable de extensión no debe ser usado a menos que sea absolutamente
necesario. El uso inadecuado de un cable de extensión puede dar lugar a un
riesgo de incendio y descarga eléctrica. Si se debe usar un cable de extensión,
asegúrese de lo siguiente:
1. Que las clavijas del enchufe del cable de extensión sean del mismo número
y forma que las del enchufe del cargador;
2. Que el cable de extensión esté conectado adecuadamente y en buena
condición eléctrica; y
3. Que la dimensión del cable sea como mínimo de 16 AWG para permitir la
clasificación de amperios de CA del cargador.
Al guardar el paquete de batería
• Mantenga seco el cargador de batería. Evite exponer el paquete de baterías a la
lluvia o a condiciones de humedad.
Antes de realizar ajustes o reparaciones
• Modeloscon paquete de batería portátil:Retire el paquete de batería de la
fuente de baterías del motor.
• Modelos con paquete de batería integrado:Desconecte el arnés de cables del
motor de arranque.
ADVERTENCIA
Los químicos de las baterías son tóxicos y corrosivos.
El fuego o la explosión pueden causar quemaduras graves o la muerte.
• Nunca queme o incinere paquetes de baterías desechados o usados, ya
que pueden explotar. Al quemar paquetes de baterías, se generan vapores y
materiales tóxicos.
• No use una batería que haya sido aplastada, dejada caer o dañada.
Características y controles
Controles del motor
Compare la ilustración (Figura: 1, 2, 3) con su motor para familiarizarse con la ubicación
de varias funciones y controles.
A. Números de identificación del motorModelo - Tipo - Código
B. Bujía
C. Silenciador, protección del silenciador (de estar equipado), supresor de chispas
(de estar equipado)
D. Arrancador eléctrico
E. Tapones de la varilla
F. Paquete de batería portátil de ion de litio
G. Rejilla de toma de aire
H. Tanque de combustible y tapa
I. Filtro de aire
J. Control de aceleración(si está equipado)
K. Cargador de batería - paquete de batería portátil
L. Cierre de combustible(si está equipado)
M. Paquete de batería integrado de ion de litio
N. Cable y cargador - paquete de batería integrado
Símbolos de control del motor y
significados
Velocidad del motor -
RÁPIDA
Velocidad del motor - LENTA
Velocidad del motor -
PARADA
ENCENDIDO/APAGADO
Arranque del motor -
Estrangulador CERRADO
Arranque del motor -
Estrangulador ABIERTO
Tapa del combustible
Apagado del combustible -
ABIERTO
Apagado del combustible -
CERRADO
Nivel de combustible -
Máximo
No lo llene en exceso
Símbolos de control de batería y
significados
Voltio Amperio
Aislamiento doble Corriente alterna
Corriente directa Producto listado en
Underwriters Laboratories,
Inc. de EE. UU. y Canadá
Producto registrado por
Underwriters Laboratories,
Inc.
Hercio
Recicle adecuadamente la
batería
Cargue el paquete de batería
Retire la llave/paquete de
batería
Operación
Recomendaciones sobre el aceite
Capacidad de aceite:vea la sección deEspecificaciones.
Not for
Reproduction
19
AVISO
Este motor fue enviado desde Briggs&Stratton sin aceite. Los fabricantes o
distribuidores de equipos pueden haber añadido aceite al motor. Antes de arrancar
el motor por primera vez, asegúrese de comprobar el nivel de aceite y agregar aceite
según las instrucciones de este manual. Si arranca el motor sin aceite, sufrirá daños
irreparables que la garantía no cubrirá.
Recomendamos el uso de aceites Briggs&Stratton
®
con garantía certificada para un
mejor rendimiento. Otros aceites detergentes de alta calidad son aceptables si están
clasificados para servicio SF, SG, SH, SJ o superior. No use aditivos especiales.
Las temperaturas exteriores determinarán la viscosidad correcta del aceite para el
motor. Use la tabla para seleccionar la mejor viscosidad para el margen de temperatura
exterior que se espera. Los motores en la mayoría de equipos de energía al aire
libre funcionan bien con aceite sintético 5W-30. Para equipos que funcionan a altas
temperaturas, el aceite sintético Vanguard
®
15W-50 proporciona la mejor protección.
A SAE30:El uso de SAE30 a temperaturas inferiores a 40°F (4°C) provocará
dificultades de arranque.
B 10W-30:El uso de 10W-30 a temperaturas mayores a 80°F (27°C) puede
provocar un aumento en el consumo de aceite. Revise el nivel de aceite con
mayor frecuencia.
C 5W-30
D 5W-30 sintético
E
Aceite sintético Vanguard
®
15W-50
Cómo revisar o agregar aceite
Consulte la figura: 4
Antes de la comprobación o aprovisionamiento de aceite
• Asegúrese de que el motor esté nivelado.
• Limpie el área de llenado de aceite y retire la suciedad.
• Consulte la sección Especificaciones para ver la capacidad del aceite.
AVISO
Este motor fue enviado desde Briggs & Stratton sin aceite. Los fabricantes o
distribuidores de equipos pueden haber añadido aceite al motor. Antes de arrancar
el motor, asegúrese de agregar aceite según las instrucciones de este manual. Si
arranca el motor sin aceite, sufrirá daños irreparables que la garantía no cubrirá.
Comprobación del nivel de aceite
1. Retire la varilla indicadora de nivel de aceite (A, Figura 4) y limpie con un paño
limpio.
2. Instale y ajuste la varilla indicadora de nivel de aceite (A, Figura 4).
3. Retire la varilla y revise el nivel de aceite. El nivel de aceite debe estar en la parte
superior del indicador de lleno (B, Figura 4) de la varilla.
Agregue aceite
1. Si el nivel es bajo, agregue aceite lentamente en el llenado de aceite del motor
(C, Figura 4). No llene en exceso. Después de añadir aceite, espere un minuto y
compruebe el nivel de aceite.
2. Vuelva a colocar la varilla y ajústela (A, Figura 4).
Recomendaciones de combustible
El combustible debe cumplir con los siguientes requisitos:
• Gasolina limpia y nueva, sin plomo.
• Un mínimo de 87 octanos/87 AKI (91 RON). Para uso en lugares elevados, ver a
continuación.
• Gasolina con hasta un 10% de etanol (gasohol) es aceptable.
AVISO No use gasolinas no aprobadas, tales como E15 y E85. No mezcle aceite
en la gasolina ni modifique el motor para que funcione con combustibles alternativos.
El uso de combustibles no aprobados dañará a los componentes del motor, los que
no estarán cubiertos bajo la garantía.
Para proteger el sistema de combustible contra la formación de goma, mézclele un
estabilizador de combustible al combustible. Vea Almacenaje. Todos los combustibles
no son iguales. Si ocurren problemas de desempeño o en el arranque, cambie
de proveedor de combustible o de marca. El funcionamiento de este motor con
gasolina está certificado. El sistema de control de emisiones de este motor es EM
(Modificaciones del Motor).
Gran altitud
En alturas de más de 5.000 pies (1524 metros), una gasolina con un mínimo de 85
octano/85 AKI(89 RON) es aceptable.
Para motores carburados es necesario el ajuste para gran altitud a fin de conservar el
rendimiento. El funcionamiento sin este ajuste genera una disminución del rendimiento,
un aumento del consumo de combustible y un incremento en las emisiones. Para
obtener información sobre el ajuste de alta altitud, póngase en contacto con un
distribuidor de servicio autorizado de Briggs & Stratton. No se recomienda operar el
motor a alturas inferiores a los 762 metros (2500 pies) con el ajuste para gran altura.
Para los motores de con inyección electrónica de combustible (EFI), no es necesario
ningún ajuste para gran altitud.
Cómo agregar combustible
Consulte la figura: 5
ADVERTENCIA
El combustible y sus vapores son extremadamente inflamables y explosivos.
El fuego y las explosiones pueden causar quemaduras graves o incluso la
muerte.
Cuando agregue combustible
• Apague el motor y deje que se enfríe por lo menos 2 minutos antes de remover la
tapa del combustible.
• Llene el tanque de combustible en exteriores o en un área bien ventilada.
• No llene excesivamente el tanque de combustible. Para permitir la expansión del
combustible, no llene el tanque por arriba de la parte inferior del cuello.
• Mantenga el combustible alejado de chispas, llamas abiertas, testigos piloto,
fuentes de calor y otras fuentes de encendido.
• Compruebe con frecuencia si existen grietas o fugas en las mangueras de
combustible, el tanque, la tapa y en los accesorios. Reemplace las piezas, si es
necesario.
• Si se derramó combustible, espere hasta que se haya evaporado antes arrancar
el motor.
1. Limpie la suciedad y los desechos en el área de la tapa de llenado de
combustible. Retire la tapa de llenado de combustible.
2. Llene el tanque de combustible (A, Figura 5) con combustible. Para permitir la
expansión del combustible, no llene el tanque por arriba de la parte inferior del
cuello (B). Algunos modelos tienen un indicador de nivel de combustible (C). No
llene el tanque por encima del indicador de nivel de combustible (D).
3. Vuelva a colocar la tapa del combustible.
Cargue el paquete de batería
Vea la figura:6789
ADVERTENCIA
El uso inadecuado de la batería o del cargador puede provocar una descarga
eléctrica o un incendio.
Al cargar el paquete de batería
• Cargue el paquete de batería Briggs & Stratton solo con el cargador de batería
Briggs & Stratton.
• No use el cargador de batería Briggs & Stratton para cargar otro tipo de baterías.
• Mantenga seco el cargador de batería. Evite exponer el paquete de baterías a la
lluvia o a condiciones de humedad.
• Para reducir el riesgo de daño al enchufe y el cable, tire del enchufe y no del
cable al desconectar el cargador.
• Un cable de extensión no debe ser usado a menos que sea absolutamente
necesario. El uso inadecuado de un cable de extensión puede dar lugar a un
riesgo de incendio y descarga eléctrica. Si se debe usar un cable de extensión,
asegúrese de lo siguiente:
Not for
Reproduction
20 BRIGGSandSTRATTON.com
1. Que las clavijas del enchufe del cable de extensión sean del mismo número
y forma que las del enchufe del cargador;
2. Que el cable de extensión esté conectado adecuadamente y en buena
condición eléctrica; y
3. Que la dimensión del cable sea como mínimo de 16 AWG para permitir la
clasificación de amperios de CA del cargador.
• No opere el cargador con un enchufe o cable dañado. El cabe alimentador
no puede reemplazarse. Si el cable está dañado, el cargador deberá ser
reemplazado de inmediato.
• No opere el cargador si ha recibido un golpe seco, ha sufrido una caída, u otro
tipo de daño. Si el cargador está dañado, debe reemplazarse. El cargador no es
reparable.
• No desmonte el cargador, ni intente poner en servicio.
• Para reducir el riesgo de descarga eléctrica, desconecte el cargador del
tomacorriente antes de limpiarlo.
• No provoque un cortocircuito; no coloque objetos en los contactos de la batería.
• El cargador no está diseñado para el uso de personas (incluidos niños) con
capacidades físicas, sensoriales o mentales reducidas, sin experiencia y
conocimiento, a menos que se les esté proporcionando supervisión o instrucción
respecto al uso del aparato por parte de una persona responsable de su
seguridad.
• Los niños deben estar supervisados para asegurarse de que no jueguen con el
cargador.
Cuándo cargar el paquete de batería
Paquete de batería portátil nuevo- El paquete de batería portátil de ion de litio se
cargó parcialmente antes del envío. Para mantener la carga y prevenir el daño durante
el almacenamiento, el paquete de batería está programado para entrar en “modo
de suspensión”. Se requiere una primera carga rápida de aproximadamente diez
(10)segundos para activar la batería. Deje el paquete de batería en el cargador hasta
que esté cargado por completo. Para cargar el paquete de batería, vea la siguiente
sección deCómo cargar el paquete de batería.
Según sea necesario: Para verificar la carga disponible, presione el botón de Indicador
de combustible de la batería (E, Figura67) y cargue si es necesario. Vea la sección
deIndicador de combustible de la batería.
Cómo cargar el paquete de batería
ADVERTENCIA
Mantenga seco el cargador de batería. Evite exponer el paquete de baterías a la
lluvia o a condiciones de humedad.
1. Conecte el cargador de batería (F, Figura89) a un tomacorriente eléctrico.
2. Paquete de batería portátil:Deslice el paquete de batería (G, Figura8) con
firmeza en el compartimento de carga de la batería (F). Si la luz de carga roja no
se enciende, retire el paquete de batería e instale nuevamente. Asegúrese de que
el paquete de batería esté fijado en el compartimento de carga de la batería.
• La luz roja (A, Figura6) indica que el paquete de batería carga con
normalidad.
• La luz verde (B) indica que le carga del paquete de batería está completa.
• La luz roja (C) que parpadea indica que el paquete de batería está
o muy caliente o muy frío y no acepta la carga. Deje conectado el
paquete de batería y cuando se alcance la temperatura normal de
funcionamiento, comenzará a cargarse automáticamente. Vea la sección
deEspecificacionespara la temperatura normal de funcionamiento.
• Las luces rojas/verdes (D) que parpadean indican que el paquete de batería
no puede cargarse y debe ser reemplazado.
3. Paquete de batería portátil:De “modo de suspensión”, la batería estará activa
en aproximadamente diez (10) segundos.
4. Paquete de batería portátil:Un paquete de batería completamente descargado
se cargará por completo en aproximadamente una (1) hora. El paquete de batería
se mantendrá completamente cargado si se deja en el cargador.
5. Paquete de batería portátil:Cuando la luz verde indique que el paquete de
batería está completamente cargado, retire el paquete de batería del cargador.
6. Paquete de batería integrado:Conecte el enchufe del cargador (G, Figura9) al
motor.
7. Paquete de batería integrado:Un paquete de batería completamente
descargado se cargará por completo en aproximadamente cuatro (4) horas.
8. Paquete de batería integrado:Cuando esté conectado al cargador, si todas
las luces de la pantalla están apagadas, la batería está completamente cargada.
Desconecte el cargador.
9. Para verificar la carga disponible, presione el botón de Indicador de combustible
de la batería (E, Figura67).
10. Cuando no esté en uso, desconecte el cargador de la batería del tomacorriente
eléctrico.
Indicador de combustible de la batería
Para verificar la carga disponible, presione el botón de Indicador de combustible de la
batería (E, Figura67). Las luces de la pantalla (H) indicarán la cantidad aproximada de
carga disponible restante en la batería.
Luces de la pantalla Carga disponible
Cuatro luces De 75% a 100%
Tres luces De 50% a 75%
Dos luces De 25% a 50%
Una luz De 10% a 25%
Luces que parpadean Baja
Paquete de batería integrado:Cuando esté conectado al cargador, si todas las luces
de la pantalla están apagadas, la batería está completamente cargada. Desconecte el
cargador.
la sección
Vea la figura:10,11,12,13
Arranque del motor
ADVERTENCIA
El combustible y sus vapores son extremamente inflamables y explosivos.
El fuego o la explosión pueden causar quemaduras graves o la muerte.
Cuando arranque el motor
• Asegúrese de que la bujía, el silenciador, la tapa del combustible y el filtro de aire
(si está equipado) estén colocados y fijos en su lugar.
• No arranque el motor sin la bujía.
• Si el motor se ahoga, ajuste el estrangulador (si está equipado) en la posición
ABIERTO o MARCHA, mueva el acelerador (si está equipado) a la posición
RÁPIDO y arranque el motor hasta que encienda.
ADVERTENCIA
El uso inadecuado de la batería y del cargador puede provocar una descarga
eléctrica o un incendio.
Cuando opere el equipo
• Mantenga el cargador de batería seco. Evite exponer el paquete de baterías a la
lluvia o a condiciones de humedad.
• Para reducir el riesgo de una descarga eléctrica, no permita que ingrese agua en
el enchufe de CA.
• No provoque un cortocircuito; no coloque objetos en los contactos de la batería.
ADVERTENCIA
PELIGRO DE GAS NOCIVO Las emisiones del motor contienen monóxido
de carbono, un gas nocivo que podría causar la muerte en minutos. NO es
posible verlo, olerlo, o saborearlo. Incluso si no huele los gases del escape,
puede estar expuesto al monóxido de carbono. Si comienza a sentirse
mareado o débil cuando utiliza este producto, apáguelo y tome aire fresco
INMEDIATAMENTE. Consulte a un médico. Es probable que se haya intoxicado
con monóxido de carbono.
• Opere este producto ÚNICAMENTE en lugares abiertos, alejado de ventanas,
puertas y ductos de ventilación para reducir el riesgo de contaminación por
monóxido de carbono el cual se acumula en espacios confinados.
• Instale alarmas de monóxido de carbono operadas por baterías o alarmas
de monóxido de carbono para enchufar con batería de seguridad según las
instrucciones del fabricante. Los detectores de humo no detecta el gas de
monóxido de carbono.
• NO opere este producto al interior de casas, estacionamientos, sótanos,
deprimidos, cobertizos, u otros espacios parcialmente cerrados incluso si utilice
ventiladores o abre puertas y ventanas para ventilación. El monóxido de carbono
puede acumularse rápidamente en estos espacios y puede prolongarse por horas,
incluso después de que el equipo ha sido apagado.
• SIEMPRE ubique este producto a favor del viento y mantenga el escape del motor
alejado de los espacios confinados.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Simplicity 09P70B-0273-H5 Manuel utilisateur
- Catégorie
- Accessoires pour véhicules automobiles
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Simplicity 100602-0161-H8 Manuel utilisateur
-
Simplicity 100605-0046-H8 Manuel utilisateur
-
Simplicity MANUAL, OPERATOR'S Manuel utilisateur
-
-
-
-
Simplicity ENGINE, MODELS 11000B 120000B Manuel utilisateur
-