MartinLogan Motion MW4-LCR Manuel utilisateur

Marque: MartinLogan

Modèle: Motion MW4-LCR

Taper: Manuel utilisateur

Ce manuel convient également à

Motion

See your local MartinLogan dealer for new construction pre-install brackets (sold separately).

M C 4 | M C 6 | M C 6 - H T

M C 8 | M W 6 | M W 4 - L C R

user’s manual

Content Check List ..................2

Safety Warnings and WEEE Recycling ....2

Square Grilles, Pre-Installation Brackets,

& Backboxes ...................3

Protect Your Investment ...............6

Break-In .........................6

General Speaker Placement ...........6

Placement Options (All Models) .........7

Placement Options (Aimable MC6-HT Speaker) 7-

Connection ......................9

In-Ceiling Mounting (pictorial) .........10

In-Wall Mounting (pictorial) ...........11

Installation ......................12

Painting the Speaker Grille ...........12

FAQ & Troubleshooting .............13

Warranty and Service ..............14

Specifications ....................16

Safety Warnings and WEEE Recycling

The lightning bolt flash with arrowhead symbol within an equilateral triangle is intended

to alert the user to the presence of uninsulated “dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the litera-

ture accompanying the appliance.

The fire within an equilateral triangle is intended to alert the user to the potential of

creating a fire hazard if they do not follow the instructions.

The dollar sign within an equilateral triangle is intended to alert the user that they run

the risk of causing damage that could be potentially expensive to repair if they don't

follow the instructions.

WARNING!

• Refer servicing to a qualified technician.

• To prevent fire or shock hazard, do not expose this module to moisture.

• Turn amplifier off should any abnormal conditions occur.

• Do not drive speaker beyond its rated power.

Content Check List

You will find the following items enclosed for your new MartinLogan loudspeaker. Should you

require assistance please call our service department at (785) 749-0133.

• Install Template • Grille Cover

In accordance with the European Union WEEE (Waste Electrical and Electronic

Equipment) directive effective August 13, 2005, we would like to notify you that this

product may contain regulated materials which upon disposal, according to the WEEE

directive, require special reuse and recycling processing.

For this reason MartinLogan has arranged with our distributors in European Union

member nations to collect and recycle this product at no cost to you. To find your local

distributor please contact the dealer from whom you purchased this product, email info@

martinlogan.com or visit the distributor locator at www.martinlogan.com.

Please note, only this product itself falls under the WEEE directive. When disposing of

packaging and other related shipping materials we encourage you to recycle these items

through the normal channels.

Square Grilles, Pre-Installation Brackets, & Backboxes

Square grilles, pre-installation brackets, and retrofit backboxes are available for certain MartinLogan

Motion Series srchitectural speakers. Contact your dealer for availability.

MC4/6/8: Multiple speakers,

distributed audio.

Fig. 1a

MC6-HT: Non-direct rear channels in

a 7.1-channel system.

Min. 12

-14

Min. 12

-14

MC6-HT: Front left, center, and

right speakers.

MC6-HT: Front left and right speakers.

MC6-HT: Non-direct surround

channels in a 5.1-channel system.

MC6-HT: Non-direct rear channel in

a 6.1-channel system.

Fig. 2a

Fig. 2b

Fig. 3b

Fig. 3a

Fig. 3c

Min. 12

MC6-HT: Direct radiating surround and

rear channels in a 7.1-channel system.

MC6-HT + MC4/6/8: Direct

radiating front, left center, surrounds

and rear channels in a 7.1.4-channel

system with Atmos height speakers.

Fig. 3d Fig. 4a

Protect Your Investment

• Use an amp that approximately matches the speaker's specified power handling.

• To avoid damage, turn down the volume if the speaker sounds like it is distorting, sounds

harsh, or the bass begins to break up.

• Tone controls and equalizers may increase the likelihood of distortion, especially at high vol-

umes. Use these settings sparingly.

Break-In

When you first begin to play your speakers, they will sound a bit bass shy. This is due to the high

quality, long-life components used in the drivers. Allow approximately 72 hours of break-in at

90dB (moderate listening levels) before any critical listening.

General Speaker Placement

Choosing a Mounting Location

Install the speakers between wall studs or ceiling joists being careful to avoid electrical wires

behind the wall's surface. Please note, MC6-HT should only be used in-ceiling.

Wall Rigidity Results in Better Sound

Increasing the rigidity of your walls may improve sonic performance. To do this consider adding

cross bracing inside of the wall approximately 12-inch (30cm) above and below the speaker.

Achieving Superior Imaging

These MartinLogan in-wall and in-ceiling speakers offer superb imaging and flexible placement in

nearly any location. However, for best performance and imaging place speakers equidistant from

the primary listening position and avoid physical obstructions between the speaker and primary

listening position.

Balancing Hard vs. Soft Surfaces Improves High- and Mid-Frequency Performance

Rooms that are “over damped” with carpeting, drapes, and other sound absorbers can cause

your system to sound dull and lifeless. On the other hand, rooms can have so many hard surfaces

that the system sounds like a gymnasium. Experiment by adding or removing soft surfaces until you

find a mix that sounds good to you.

Balancing Bass Output

Corner placement of these speakers will reinforce their bass output. If you require balanced output

across the entire audio spectrum avoid mounting these speakers in a corner.

When choosing placement follow these simple recommendations. Keep in mind these are just

recommendations and your unique installation requirements may dictate otherwise:

• Place a minimum of 12-inches (30cm) from any wall corner.

• Place fronts/centers equidistant between 10–14 feet (3–4.3m) from the listening position.

• MC4, MC6, MC6-HT, and MC8: Install in-ceiling only.

Placement Options (All Models)

The Motion series architectural speakers feature MartinLogan’s Folded Motion Tweeter or

FMT. This unique thin film tweeter features a controlled dispersion pattern of 80° by 80°. This

controlled “cone of sound” can be extremely useful in avoiding sound reflections in the room

which would otherwise result in diminished sound quality. For optimal results, attention should

be paid to the mounting location to help ensure that the primary listening area is within the dis-

persion pattern of the tweeter. Keep in mind, the farther away the listener is from the speaker,

the wider the coverage area of the tweeter becomes. Because of the uniform dispersion of

the FMT, the dispersion of Motion In-wall speakers remains the same whether the speaker is

mounted horizontally or vertically. Controlled Dispersion is a tool to help deliver better sound

quality where it actually matters, your ears! The dispersion of the FMT can be used to help

eliminate unwanted sound reflections or help reduce unwanted “sound leakage” into other

areas of the home, especially in open floor plans.

Stereo and Home Theater Applications (no illustration)

MartinLogan Motion series in-wall and in-ceiling speakers are ideal for 2-channel stereo and

multi-channel home theater installations. The guidelines from the previous section apply to both

in-wall and in-ceiling speakers.

Multiple Speakers, Distributed Audio (Fig. 1a)

In larger areas (offices, etc.) multiple speakers may be used to eliminate the sound imbalances

that occur with separate stereo speakers as people move around the room, or are seated closer

to one speaker than the other. Position speakers to achieve the broadest sound coverage in the

main listening area. The angled MC6-HT can be useful to help aim and focus sound towards an

area you are trying to cover.

Placement Options (Aimable MC6-HT Speaker)

MC6-HT speakers are optimized for use in rooms with ceiling heights ranging from 8–9 feet (2.4–

2.74m). Point the tweeter toward the primary listening position. For overall clarity and balanced

bass performance, these speakers should be mounted in the ceiling 12 inches (30 cm) or more

from the wall, as shown in Figs. 2a to 4a.

Front Channel Placement (Fig. 2a & 2b)

Follow the general guidelines for speaker placement provided at the beginning of the main section

keeping in mind the distance from the front speakers to your primary listening area should be

10–14 feet (3–4.3m), as shown. Point the drivers toward the primary listening position.

Non-Direct Radiating Surround/Rear Placement (Fig. 3a-3c)

These speakers are also ideal for use as surround or surround back channels. Aiming the speaker

so sound bounces off the walls creates an enveloping, reverberant sound field. Keep in mind that

speakers should be mounted 12 inches (30 cm) or more from the wall.

• 5.1-Channel Surround Placement (Fig. 3a): Position one speaker on either side of the listening

area, with drivers pointed toward the side walls.

• 6.1-Channel Rear Placement (Fig. 3b): Begin with ‘5.1-Channel Surround Placement’ (above).

Center one speaker behind the listening area with drivers pointed toward the back wall.

• 7.1-Channel Rear Placement (Fig. 3c): Begin with ‘5.1-Channel Surround Placement’ (above).

Position another pair of MC6-HT speakers behind the listening area, one slightly to the right,

the other slightly to the left, with drivers pointed to the back of the room as shown.

Direct Radiating Surround/Rear Center Placement (Fig. 3d & 4a)

The MC6-HT may be used as direct-radiating speakers, positioned with drivers pointed toward the

listening area. Use Fig.3d or 4a as a guide to positioning as you experiment to achieve optimal

surround sound in your room.

Motion LCR Model Placement (no illustration)

The MW4-LCR is a true Left, Center, Right (“LCR”) model that can be used for any in-wall position

in a stereo or home theater setup. This model is designed to mount either vertically or horizontally

as desired or otherwise dictated by your unique installation.

Connection

Connect the red (+) amplifier terminal to the red (+) speaker terminal. Connect the black (-)

amplifier terminal to the black (-) speaker terminal.

Installation

NOTE: These instructions assume the mounting surface is of standard wood frame and standard

sheet rock construction. If you wish to mount the speakers to another type of material, you should

contact a bonded contractor.

NOTE: See your local dealer for new construction pre-install brackets, square grilles (in-ceiling

models only) and back boxes (in-ceiling models only) (accessories sold separately).

NOTE: While it is possible to use a manual screwdriver for installation, we strongly suggest using a

power drill. To avoid damaging or breaking the clamps, set your drill to a HIGH SPEED but LOW

TORQUE setting. A high power setting is NOT necessary and may cause clamps to crack or break

from the added force.

Such damage is not covered under warranty.

WARNING! Before installing check local building codes to verify compliance

with local regulations. WARNING! Before installing check for obstructions behind

drywall. To do this make a small hole, cutting at a 45° angle (this will make the

hole easier to patch if obstructions are found). Only cut out the mounting hole after

you have verified there are no obstructions behind the dry wall. WARNING! Use

only speaker cable that is rated for in-wall use. The UL standard is CL2, CL3, and

CM. The CSA standard is FT4. WARNING! Turn your amplifier off before making

or breaking any signal connections.

NOTE: Retrofit Back Boxes are available for all in-ceiling Motion series speakers. These back

boxes reduce sound from “leaking” into the area above where the speaker is installed. For exam-

ple, if building a home theater downstairs and there are living spaces directly above where the

speakers are installed it may be desirable to use these back boxes to help contain the sound so it

does not cause any disturbance to those above the speakers.

Recommended tools:

• Stud finder

• Sharp pencil or pen

• Dry wall knife/saw

• Wire strippers

• Power drill

• Tape measure

• Low-tack tape

✔

✘

SpeakerInstallation andConnection

(pictorial)

NOTE: If the clamps are not set to the right position, useascrewdrivertoturn

the screws counter-clockwise until the clampsare in the correct position.

Fig.5c

Fig.5a

Fig.5d

Fig.5b

Fig.5e

Fig. 6e

Fig. 6c

Fig. 6a

Fig. 6f

Fig. 6b

Fig. 6d

1. If the template has a removable center, remove it at this time.

2. Using a stud finder, position the template completely between wall studs or ceiling joists.

MC4, MC6, MC6-HT, and MC8: Install in-ceiling only.

3. Hold or tape the template in place and mark cutout with a pencil. For rectangular

speakers, level the template before marking (Figs. 5a, 6a, & 6b).

4. Remove the template and cut out the opening with a drywall knife (Figs. 5b & 6c).

5. In-wall: If desired, place fiberglass insulation above and below the cut-out hole. Place

a half thick piece of fiberglass insulation behind the speaker. In-ceiling: If desired, place

fiberglass insulation 12" (30cm) or thicker between the joists directly above the speaker.

6. Connect speaker cables. Be consistent when connecting the speaker leads to the terminals.

Take great care to assign the same color to the (+) terminal on both the speaker and the

amplifier.

7. Set your power drill to the high speed but low torque setting.

8. Ensure the clamps on the lip of the speaker are positioned exactly as shown in the Warning

Diagrams.

9. Gently push the assembly into the ceiling or wall hole (Figs. 5c & 6d).

10. Supporting the assembly with one hand, tighten each screw using the electric drill and

Torx T20 bit. Stop tightening when you sense resistance (Figs. 5d & 6e). MC6-HT: Before

tightening screws orient speaker so the drivers are positioned towards the desired position.

11. Gently press the grille into place (Figs. 5e & 6f).

Painting the Speaker Grille

IMPORTANT! Before painting remove grille from speakers. Do not paint the surface of the speak-

er behind the grille. Do not use a paint roller.

1. Remove the grille from the speaker.

2. Paint the grille, being careful not to plug the holes. For best results use a spray rather than

a brush. Allow the paint to completely dry before proceeding. Do not paint the surface

behind the grille.

Frequently Asked Questions

How do I clean my speakers? Use a dust free cloth or a soft brush to remove the dust from your

speakers. Do not spray any kind of cleaning agent on or in close proximity to the drivers.

What size amplifier should I use? We recommend an amplifier rated within the suitable amplifier

range of your speaker.

Could you suggest a list of suitable electronics and cables that would be ideal for MartinLogan

speakers? The area of electronics and cable choice is probably the most common type of

question that we receive. It is also the most subjective. We have repeatedly found that brands that

work well in one setup will drive someone else nuts in another. We use many brands with great

success. Again, we have no favorites; we use electronics and cables quite interchangeably. We

would suggest listening to a number of brands—and above all else—trust your ears. Dealers are

always the best source for information when purchasing additional audio equipment or cables and

will be well versed in the subject of special safety requirements for in-wall cable.

Will exposure to sunlight affect the life or performance of my speakers? We recommend that

you not place any loudspeaker in direct sunlight. The ultraviolet (UV) rays from the sun can cause

deterioration of grille cloth, speaker cones, etc. Small exposures to UV will not cause a problem. In

general, the filtering of UV rays through glass will greatly reduce the negative effects.

Troubleshooting

No Output

• Check that all your system components are turned on, not muted, and that your balance con-

trol (if applicable) is set correctly.

• Check to make sure your power outlet at the wall is working.

• Check your power cords, speaker wires, and interconnecting cables.

• Check to make sure no headphones are plugged in.

• Swap speaker wires at your amplifier with those of a speaker that is functioning correctly. If

the lack of output moves to a different speaker the problem could be with other equipment in

your system (i.e. amp, pre-amp, processor, etc.)

• Try hooking up a different set of speakers. The lack of output could point to a problem with

other equipment in your system (i.e. amp, pre-amp, processor, etc.)

Lack of Bass or Poor Imaging

• Check your speaker wires. Is the polarity correct — (+) to (+) and (–) to (–)?

• The use of optional back boxes will reduce the bass output of the speaker as these

enclosures reduce the air space the woofer is able to utilize. This is the tradeoff of reducing

unwanted sound that is able to travel to other areas of the home.

Warranty

MartinLogan offers online warranty registration at www.martinlogan.com.

Your speaker is provided with an automatic Limited 90 Day Warranty coverage.

You have the option, at no additional charge, to receive a Limited 5 Year Warranty coverage.

To obtain the Limited 5 Year Warranty coverage register your speakers at www.martinlogan.com.

Save a copy of your dealer receipt as it may be requested if service is required.

MartinLogan may not honor warranty service claims unless we have a completed Warranty

Registration on file at www.MartinLogan.com!

Service

Should you be using your MartinLogan product in a country other than the one in which it was

originally purchased, we ask that you note the following:

1 The appointed MartinLogan distributor for any given country is responsible for warranty

servicing only on units distributed by or through it in that country in accordance with its

applicable warranty.

2 Should a MartinLogan product require servicing in a country other than the one in which it

was originally purchased, the end user may seek to have repairs performed by the nearest

MartinLogan distributor, subject to that distributor’s local servicing policies, but all cost of

repairs (parts, labor, transportation) must be borne by the owner of the MartinLogan product.

3 If, after owning your speakers for six months, you relocate to a country other than the

one in which you purchased your speakers, your warranty may be transferable. Contact

MartinLogan for details.

Specifications*

System Frequency Response ............

Aiming............................

Sensitivity..........................

Impedance .........................

Crossover Frequency..................

High-Frequency Driver ................

Low-Frequency Driver.................

Binding Post Inputs ...................

Suitable Amplifier Range ..............

Maximum Power Handling .............

Weight............................

Overall Size (dia. x depth) .............

Required opening

......................

Projection from wall surface ............

Depth required behind wall surface.......

*Specifications are subject to change

without notice.

MC4

90 - 25,000 Hz ±3dB

N/A

90dB @2.83V/ 1 meter

Compatible with 8 ohms

2,230 Hz

FMT Transducer

1” x 1.4” (2.6cm x 3.6cm) Opening

5.25” x 1.75” (13.3cm x 4.4cm) Diaphragm

4” (10.16cm) black fiberglass cone

Push style accommodates wire up to 12AWG

50–120 Watts

60 Watts

2.02 lbs. each (0.9 kg)

5.63" x 5.65" (14.3cm x 14.3cm)

4.89" (12.41cm) diameter

0.26" (0.65cm)

5.50" (13.9cm)

(12.41cm)

4.89”

System Frequency Response ............

Aiming............................

Sensitivity..........................

Impedance .........................

Crossover Frequency..................

High-Frequency Driver ................

Low-Frequency Driver.................

Binding Post Inputs ...................

Suitable Amplifier Range ..............

Maximum Power Handling .............

Weight............................

Overall Size (dia. x depth) .............

Required opening

......................

Projection from wall surface ............

Depth required behind wall surface.......

*Specifications are subject to change

without notice.

MC6

62 - 25,000 Hz ±3dB

N/A

90dB @2.83V/ 1 meter

Compatible with 8 ohms

2,570 Hz

FMT Transducer

1” x 1.4” (2.6cm x 3.6cm) Opening

5.25” x 1.75” (13.3cm x 4.4cm) Diaphragm

6.5” (16.51cm) black fiberglass cone

Push style accommodates wire up to 12AWG

50–150 Watts

75 Watts

5.1 lbs. each (2.31 kg)

8.64" x 4.57" (21.94cm x 11.61cm)

7.65" (19.43cm) diameter

0.31" (0.77cm)

4.43" (11.26cm)

Specifications*

System Frequency Response ............

Aiming............................

Sensitivity..........................

Impedance .........................

Crossover Frequency..................

High-Frequency Driver ................

Low-Frequency Driver.................

Binding Post Inputs ...................

Suitable Amplifier Range ..............

Maximum Power Handling .............

Weight............................

Overall Size (dia. x depth) .............

Required opening

......................

Projection from wall surface ............

Depth required behind wall surface.......

*Specifications are subject to change

without notice.

MC6-HT

90 - 25,000 Hz ±3dB

N/A

90dB @2.83V/ 1 meter

Compatible with 8 ohms

2,230 Hz

FMT Transducer

1” x 1.4” (2.6cm x 3.6cm) Opening

5.25” x 1.75” (13.3cm x 4.4cm) Diaphragm

4” (10.16 cm) black fiberglass cone

Push style accommodates wire up to 12AWG

50–120 Watts

60 Watts

6.08 lbs. each (2.75 kg)

11.30" x 6.88" (28.7cm x 17.48cm)

10.23" (25.9cm) diameter

0.35" (0.89cm)

6.77" (17.18cm)

System Frequency Response ............

Aiming............................

Sensitivity..........................

Impedance .........................

Crossover Frequency..................

High-Frequency Driver ................

Low-Frequency Driver.................

Binding Post Inputs ...................

Suitable Amplifier Range ..............

Maximum Power Handling .............

Weight............................

Overall Size (dia. x depth) .............

Required opening

......................

Projection from wall surface ............

Depth required behind wall surface.......

*Specifications are subject to change

without notice.

MC8

44 - 25,000 Hz ±3dB

N/A

91dB @2.83V/ 1 meter

Compatible with 8 ohms

2,220 Hz

FMT Transducer

1” x 1.4” (2.6cm x 3.6cm) Opening

5.25” x 1.75” (13.3cm x 4.4cm) Diaphragm

8” (20.32cm) black fiberglass cone

Push style accommodates wire up to 12AWG

50–200 Watts

100 Watts

6 lbs. each (2.72 kg)

10.35" x 4.95" (26.28cm x 12.57cm)

9.25" (23.5cm) diameter

0.33" (0.83cm)

4.81" (12.22cm)

(2.5cm)

1”

MAX CEILING THICKNESS

MOUNTING LOCKS

EXTEND 0.375in [9.5mm]

BEYOND EDGE

(26.28cm)

10.35”

(23.50cm)

9.25”

(12.57cm)

4.95”

(12.22cm)

4.81”

(13.06cm)

5.14”

(0.83cm)

0.33”

(26.42cm)

10.40”

Specifications*

System Frequency Response .......

Aiming.......................

Sensitivity.....................

Impedance ....................

Crossover Frequency.............

High-Frequency Driver ...........

Low-Frequency Driver............

Binding Post Inputs ..............

Suitable Amplifier Range .........

Maximum Power Handling ........

Weight.......................

Overall Size (l x w x depth)........

Required opening

................

Projection from wall surface .......

Depth required behind wall surface..

*Specifications are subject to change

without notice.

MW6

62 - 25,000 Hz ±3dB

N/A

90dB @2.83V/ 1 meter

Compatible with 8 ohms

2,920 Hz

FMT Transducer

1” x 1.4” (2.6cm x 3.6cm) Opening

5.25” x 1.75” (13.3cm x 4.4cm) Diaphragm

6.5” (16.51cm) black fiberglass cone

Push style accommodates wire up to 12AWG

50–120 Watts

60 Watts

6 lbs. each (2.72 kg)

8.04" x 11.07" x 4.16" (20.43cm x 28.13cm x 10.55cm)

6.97" x 11.07" (17.70cm x 28.13cm)

0.31" (0.79cm)

4.04" (10.25cm)

(17.70cm)

6.97”

(20.61cm)

8.12”

(20.43cm)

8.04”

(10.55cm)

4.16”

(10.25cm)

4.04”

(11.04cm)

4.35”

(0.79cm)

0.31”

(28.13cm)

11.07”

(28.13cm)

11.07”

(28.31cm)

11.15”

(2.5cm)

1”

MAX CEILING THICKNESS

MOUNTING LOCKS

EXTEND 0.375in [9.5mm]

BEYOND EDGE

La page charge ...

MartinLogan Motion MW4-LCR Manuel utilisateur

Marque: MartinLogan

Modèle: Motion MW4-LCR

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: MartinLogan Motion MW4-LCR User manual

MartinLogan Motion MW4-LCR Manuel utilisateur

Ce manuel convient également à

MartinLogan Motion MW4-LCR Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents