Tyco Tyco HC2TCHPRO Manuel utilisateur

HS2TCHPRO/HS2TCHPROBLK Touchscreen User Manual

Ecran tactile HS2TCHPRO/HS2TCHPROBLK Manuel de

l'utilisateur

Pantella de Toque HS2TCHPRO/HS2TCHPROBLK Manual del

Usuario

Tela de Toque HS2TCHPRO/HS2TCHPROBLK Manual do Usuario

WARNING: This manual contains information on limitations regarding product use, function and information

on the limitation as to liability of the manufacturer. The entire manual should be carefully read.

MISE EN GARDE: Ce manuel contient des informations sur les limitations concernant l’utilisation et le fonc-

tionnement du produit ainsi que des informations sur les limitations et les obligations du fabricant Lisez attent-

ivement le guide complet.

AVISO: Este manual contiene información sobre limitaciones referentes a la utilización y al funcionamiento del

producto e información sobre las limitaciones de las responsabilidades del fabricante. Todo el manual debe leerse

atentamente.

ADVERTÊNCIA: Este manual contém informações sobre limitações em relação ao uso e funcionamento do

produto, bem como informações sobre as limitações de responsabilidade do fabricante. Todo o manual deve ser

lido com atenção.

Table of Contents

Table of Contents 2

Safety Notes 5

Important Safety Instructions 5

Regular Maintenance and Troubleshooting 5

Handling Precautions 5

Cleaning 5

Troubleshooting 5

Introduction 6

General System Operation 6

About Your Security System 6

Carbon Monoxide Detection (must be enabled by your Installer) 7

Fire Detection (must be enabled by your Installer) 7

Testing 7

Monitoring 7

Maintenance 7

Important Notice 7

Specifications and Features 8

Welcome Screen 8

Emergency Keys 9

Arming and Disarming the System 10

Stay Arm (Arming the Perimeter) 10

Silent Exit Delay 10

Disarm 11

Away Arm 11

Exit Delay Time Restart 11

Alarm Cancel Window 11

Bell/Siren Sounds After Away Arming 12

Audible Exit Fault 12

Arming Error 12

Remote Arming and Disarming 12

Using Your System 12

When Alarm Sounds 12

Intrusion (Burglary) Alarm Continuous Siren 12

If the Intrusion Alarm was Accidental 13

Fire Alarm Pulsed Siren 13

Wireless Carbon Monoxide Alarm 13

Troubles 14

Alarm Memory 14

Sensor Reset 15

Outputs 15

Additional Functions 16

Photos 16

Quick Exit 16

Time & Date Programming 16

Keypad Mode 16

Door Chime (Chime enable/disable) 16

Zone Bypass 16

Zone Status Indicators 17

Bypassed Zones 17

Bypassing Zones with a HS2TCHPRO/HS2TCHPROBLK 17

Options Menu 17

Access Codes 18

Assign Proximity Tags 18

Delete Proximity Tags 18

User Code Attributes 19

Inherent Attributes (all codes except installer and maintenance) 19

Programmable Attributes 19

Bell Squawk Attribute 19

Partition Assignment 19

Erasing an Access Code 19

Installer Menu 19

User Functions 20

Time and Date 20

Auto-Arm Time 20

Enable DLS/Allow System Service 20

Event Buffer 20

System Test 20

Auto-Arm/Disarm Control 21

User Call-up 21

Engineer's Reset 21

Keypad Configuration 21

Chime Enabled/Disabled 22

Arming 22

Partition Status 22

Keypad Mode 23

Managing Partitions 23

Partitions 23

Single Partition Operation 23

Loaning a Keypad to Another Partition 23

Global Keypad Operation 24

Fire and CO Zone Types 25

Testing Your System 26

Testing Your Keypad Sounder and Siren 26

Testing Your Entire System 26

Walk Test Mode 26

Allowing Computer Access To Your System 26

Reference Sheets 27

System Information Enabled? 27

For Service 27

Central Station Information: 27

Installer Information: 27

Battery Installation / Service Date: 27

Access Codes (copy as needed) 28

Sensor / Zone Information (copy as needed) 29

Guidelines for Locating Smoke Detectors and CO Detectors 30

Smoke Detectors 30

Carbon Monoxide Detectors 31

Household Fire Safety Audit 32

Fire Escape Planning 32

License Agreement 33

Safety Notes

This manual shall be used in conjunction with the PowerSeries Pro User manual for the compatible alarm control

panel: HS3032, HS3128, HS3248.

Always ensure you obtain the latest version of the User Guide. Updated versions of this User Guide are available

by contacting your distributor.

Warning: Read and save these instructions! Follow all warnings and instructions specified within this document

and/or on the equipment.

Important Safety Instructions

To reduce the risk of fire, electric shock and/or injury, observe the following:

l Do not spill any type of liquid on the equipment.

l Do not attempt to service this product yourself. Opening or removing the cover may expose you to dan-

gerous voltage or other risk. Refer servicing to qualified service personnel. Never open the device your-

self.

l Do not touch the equipment and its connected cables during an electrical storm; there may be a risk of

electric shock.

l Do not use the Alarm System to report a gas leak if the system is near a leak.

Regular Maintenance and Troubleshooting

Keep your HS2TCHPRO/HS2TCHPROBLK Touchscreen keypad in optimal condition by following all the instruc-

tions that are included within this manual and/or marked on the product.

Handling Precautions

Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to

vary.

Cleaning

l If the display surface is contaminated, breathe on the surface and gently wipe it with a soft, dry cloth. If

still not completely clean, moisten cloth with isopropyl alcohol.

l Do not use abrasives, water, thinners, solvents or aerosol cleaners (spray polish), any aromatic solvents,

ketones etc. that may enter through holes in the HS2TCHPRO/HS2TCHPROBLK Touchscreen keypad

and cause damage.

Troubleshooting

Occasionally, you may have a problem with your system. If this happens, your Alarm Controller will display an

error message. Refer to the provided list when you see an error message on the display. If additional help is

required, contact your distributor for service.

Warning: This equipment, HS2TCHPRO/HS2TCHPROBLK Touchscreen keypad shall be installed and used

within an environment that provides the pollution degree max 2 and over-voltages category II non-hazardous loc-

ations, indoor only. It is designed to be installed, serviced and/or repaired by service persons only [service person

is defined as a person having the appropriate technical training and experience necessary to be aware of hazards to

which that person may be exposed in performing a task and of measures to minimize the risks to that person or

other persons]. There are no parts replaceable by the end-user within this equipment.

Warning: Never obstruct the access to the Alarm controller to which this equipment is connected. These safety

instructions should not prevent you from contacting the distributor and/or the manufacturer to obtain any further

clarification and/or answers to your concerns.

- 5 -

Introduction

Figure 1- Controls and Indicators

The HS2TCHPRO/HS2TCHPROBLK Touchscreen is an interactive touch-sensitive color LCD that can be used on

any PowerSeries Pro control panel. Due to the custom requirements of individual installations, some of the fea-

tures described here may perform differently than described. Refer to your Installer's Instructions for the details of

your specific installation and to the User Manual for general security system information.

General System Operation

Your security system is made up of a DSC control panel, one or more keypads and various sensors and detectors.

The control panel will be mounted out of the way in a utility closet or in a basement. The metal cabinet contains

the system electronics, fuses and standby battery.

Note: Only the installer or service professional shall have access to the control panel.

All the keypads have an audible indicator and command entry keys. The keypad is used to send commands to the

system and to display the current system status. The keypad(s) will be mounted in a convenient location inside

the protected premises close to the entry/exit door(s).

The security system has several zones of protection, each connected to one or more sensors (motion detectors,

glassbreak detectors, door contacts, etc.). "Alarm Memory" on page14 for information on sensors in alarm for this

Touchscreen keypad.

About Your Security System

Your DSC Security System has been designed to provide you with the greatest possible flexibility and con-

venience. Read this manual carefully and have your installer instruct you on your system's operation and on which

features have been implemented in your system. All users of this system should be equally instructed in its use.

Fill out the “System Information” page with all of your zone information and access codes and store this manual

in a safe place for future reference.

Note: The PowerSeries security system includes specific false alarm reduction features and is classified in accord-

ance with ANSI/SIA CP-01-2010 Control Panel Standard - Features for False Alarm Reduction. Please consult your

installer for further information regarding the false alarm reduction features built into your system as all are not

covered in this manual.

- 6 -

Introduction

Carbon Monoxide Detection (must be enabled by your Installer)

This equipment is capable of monitoring carbon monoxide detectors and providing a warning if carbon monoxide

is detected. Please read the Family Escape Planning guidelines in this manual and instructions that are available

with the carbon monoxide detector.

Fire Detection (must be enabled by your Installer)

This equipment is capable of monitoring fire detection devices such as smoke detectors and providing a warning

if a fire condition is detected. Good fire detection depends on having adequate number of detectors placed in

appropriate locations. This equipment should be installed in accordance with NFPA 72 (N.F.P.A., Batterymarch

Park, Quincey MA 02269). Carefully review the Family Escape Planning guidelines in this manual.

Testing

To ensure that your system continues to function as intended, you must test it weekly. Please refer to the “Testing

your System” section in this manual. If your system does not function properly, call your installing company for

service.

Monitoring

This system is capable of transmitting alarms, troubles and emergency information to a central station. If you ini-

tiate an alarm by mistake, immediately call the central station to prevent an unnecessary response.

Note: The monitoring function must be enabled by the installer before it becomes functional.

Note: There is a communicator delay of 30 seconds in this control panel. It can be removed, or it can be increased

up to 45 seconds, at the option of the end-user by consulting with the installer.

Note: For CP-01 systems, the monitoring function must be enabled by the installer before it becomes functional.

Maintenance

With normal use, the system requires minimum maintenance. Note the following points:

l Use the system test described in “Testing Your System” to check the battery condition. We recommend,

however that the standby batteries be replaced every 3 - 5 years.

l For other system devices such as smoke detectors, passive infrared, ultrasonic or microwave motion

detectors, or glassbreak detectors, consult the manufacturer's literature for testing and maintenance

instructions.

Important Notice

A security system cannot prevent emergencies. It is only intended to alert you and, if included, your central sta-

tion of an emergency situation. Security systems are very reliable but they may not work under all conditions, and

they are not a substitute for prudent security practices or life and property insurance. Your security system should

be installed and serviced by qualified security professionals who should instruct you on the level of protection

that has been provided and on system operations.

- 7 -

Specifications and Features

Display 7" TFT (800 x 480) pixel) Color Touchscreen

Home button Home/Calibration/Reset

LED indicators 4 (Ready, Armed, Trouble, AC)

Dimensions (mounting) 8.5" x 5.1" x 0.8" [127.9 mm (L) x 195 mm (W) x 20.35 mm (D)]

Horizontal viewing angle 70°

Vertical viewing angle 70° (top), 50° (bottom)

Brightness 280 cd/m²

Operating environment

0°C to +49°C (32°F to 120°F)

93% (max) relative humidity non-condensing

SD card slot Holds any standard Secure Digital (SD) card* (32 x 24 x 2.1 mm)

*If necessary, the SD card can be formatted to file system FAT16 or 32 using a PC. The maximum size SD card

supported is 32GB.

Welcome Screen

The date and time are displayed in the upper right corner of the screen. The system status (i.e., Ready, Armed, Exit

Delay etc.) is displayed at the top of the screen.

Figure 2- Welcome Screen

- 8 -

Emergency Keys

Figure 3- Emergency Screen

When the emergency key is pressed, a new screen is displayed with:

Fire Fire Assistance Required. Press and hold for 2 seconds to activate.

Medical Medical Assistance Required. Press and hold for 2 seconds to activate.

Panic Police Assistance Required. Press and hold for 2 seconds to activate.

Important: The Medical and Panic keys are ON by default. The Fire key will not function unless programmed by

the Installer. Please ask your installer if the Fire, Medical and Panic keys are enabled.

Note: These events are recorded in the log.

- 9 -

Arming and Disarming the System

Stay Arm (Arming the Perimeter)

Ask your alarm company if this function is available on your system.

Stay arming bypasses the interior protection (i.e., motion sensors) and arms the perimeter of the system (i.e., doors

and windows). Close all sensors (i.e., stop motion and close doors). The Ready ( ) indicator should be on. Press

the Stay Arm button and/or enter your Access Code and do not leave the premises (if your installer has pro-

grammed this button). During exit delay, the Armed ( ) and Ready( )indicators turn on to visually indicate

that the system is arming.

When the exit delay expires, the Ready LED turns off, the Armed LED remains on and the keypad stops sounding

to indicate that the alarm system is armed.

Note: For SIA FAR listed panels, the Stay Arming exit delay will be twice as long as the Away Arming exit

delay.

Silent Exit Delay

If the system is armed using the Stay Arm button or using the "No Entry" Arming method ([*][9][access code], the

audible progress annunciation (keypad buzzer) is silenced and the exit time doubled for that exit period only (CP-

01 versions only).

Note: For non CP-01 versions, Standard exit time is used.

When Stay Arm is selected from the Home screen:

l The display indicates “Exit Delay in Progress,” and the pre-programmed exit delay begins.

l The Armed LED Indicator turns on.

If Quick Arm is not enabled by the installer, then a numerical keypad is displayed (see following figure). Enter a

valid access code to proceed.

Figure 4- Keypad

If Disarm is selected during the exit delay, a numeric keypad is displayed.

l Enter (tap) your access code.

l The arming sequence is aborted and the system returns to the Home screen.

l The Armed LED turns OFF.

At the end of the pre-programmed exit delay:

- 10 -

Arming and Disarming the System

l The Disarm screen is displayed.

l The Ready Indicator turns OFF.

l “Stay Armed-Bypass” is displayed in the Status Bar.

Note: This screen will go into stand-by mode after 15 minutes. Tap the screen to restore the display.

Disarm

If Disarm is selected:

l A numerical keypad is displayed.

l Enter your Access Code in the keypad.

l The system returns to the Home screen and the red Armed indicator turns OFF.

l The alarm status is momentarily displayed in the status bar, then "Ready" is displayed.

l The green Ready indicator turns ON.

Note: If your code is invalid, the system will not disarm and a 2-second error tone will sound. If this happens,

press # and try again.

Away Arm

When Away Arm is selected:

l Enter a valid access code to proceed.

l The Armed LED Indicator turns ON.

l "Exit Delay in Progress" is displayed in the Status Bar. The pre-programmed exit delay begins.

l The touchscreen "beeps" at a 1-second urgency interval during the exit delay. Then 3 beeps sound in the

last 10 seconds.

Note: If Quick Arm is not enabled by the installer, a numerical keypad is displayed.

If Disarm is selected during the exit delay:

l A numeric keypad is displayed. Tap your access code.

l The Arming sequence is aborted and the system returns to the Home screen.

l The Armed LED turns OFF.

At the end of the pre-programmed exit delay:

l The Disarm screen is displayed.

l The Ready Indicator turns OFF.

l "Away Armed" is displayed in the Status Bar.

Exit Delay Time Restart

The control panel provides an option where if an entry/exit zone is tripped, a second time prior to the end of the

exit delay, the exit delay time restarts. The exit delay timer can only be restarted once.

Alarm Cancel Window

The control panel provides a period of time in which the user can cancel the alarm transmission. The minimum dur-

ation of this time is five minutes. If the programmed alarm transmission delay has expired, canceling an alarm

sends a message to the monitoring station. Upon a successful transmission of the cancelation message, the keypad

will beep 6 times.

- 11 -

Arming and Disarming the System

Bell/Siren Sounds After Away Arming

Audible Exit Fault

In an attempt to reduce false alarms, the Audible Exit Fault is designed to notify you of an improper exit when

arming the system in the Away mode. In the event that you fail to exit the premises during the allotted exit delay

period, or if you do not securely close the Exit/Entry door, the system will notify you that it was improperly

armed in two ways: the keypad will emit one continuous beep and the bell or siren will sound.

Your installer will tell you if this feature has been enabled on your system. If this occurs:

1. Re-enter the premises.

2. Enter your access code to disarm the system. You must do this before the entry delay timer expires.

3. Follow the Away arming procedure again, making sure to close the entry/exit door properly.

Arming Error

An error tone will sound if the system is unable to arm. This will happen if the system is not ready to arm (i.e.,

sensors are open), or if an incorrect user code has been entered. If this happens, ensure all sensors are secure. Press

[#] and try again, ensuring that a valid access code is entered. Please check with your installer to determine if arm-

ing is inhibited by any other means.

Remote Arming and Disarming

The system can be armed and/or disarmed using the remote wireless key or proximity tag. When arming the sys-

tem by using the Arm button on the wireless key, the system will acknowledge the command by sounding a

single bell squawk (if bell squawk is enabled). When disarming using the Disarm button on the wireless key, the

system will acknowledge the command by sounding two bell squawks (if bell squawk is enabled) that can be

heard from the exterior of the premises.

To arm the system with a proximity tag:

l Present your proximity tag to a keypad equipped with a proximity sensor anytime the system Ready

indicator is on.

l If configured by your installer, enter your access code.

To disarm the system with a proximity tag:

l Present your proximity tag to a keypad equipped with a proximity sensor anytime the system is armed.

(Armed indicator is on) and if configured as required, enter your access code.

l If you walk through the entry door the keypad will beep. Present your Proximity tag within ____

seconds to avoid an alarm condition.

Using Your System

This section provides additional information about how to use your alarm system.

When Alarm Sounds

The system can generate 3 different alarm sounds:

l Temporal/pulsed siren = Fire Alarm

l 4 beeps, 5-second pause, 4 beeps = Carbon Monoxide Alarm

l Continuous siren = Intrusion (Burglary Alarm)

Note: The priority of signals is fire alarm, carbon monoxide alarm and medical alarm, then burglary alarm.

Note: Medical alarm is silent. It only results in an alarm transmission to the monitoring station.

Intrusion (Burglary) Alarm Continuous Siren

If you are unsure of the source of the alarm, approach with caution! If the alarm was accidental,

enter your Access Code to silence the alarm. Call your central station to avoid a dispatch.

- 12 -

Arming and Disarming the System

If the Intrusion Alarm was Accidental

1. Enter your Access Code to silence the alarm. If the code is entered within 30s (or the programmed value of

the alarm transmission delay) the transmission of the alarm to the monitoring station will be canceled.

2. Call your central station to avoid a dispatch.

Fire Alarm Pulsed Siren

Follow your emergency evacuation plan immediately!

If the fire alarm was accidental (e.g., burned toast, bathroom steam, etc.), enter your Access Code to silence the

alarm. Call your central station to avoid a dispatch. To reset the detectors, see the Sensor Reset section.

Wireless Carbon Monoxide Alarm

Activation of your CO alarm indicates the presence of carbon monoxide (CO), which can be fatal. During an alarm,

the red LED on the CO detector flashes rapidly and the buzzer sounds with a repeating cadence of: 4 quick beeps,

5-second pause, 4 quick beeps. Also, during an alarm, the siren connected to the control panel produces a repeat-

ing cadence of 4 quick beeps, 5-second pause, 4 quick beeps. The keypad will also provide audible and visual

indication of the CO alarm.

If an Alarm Sounds:

1. Operate silence button.

2. Call emergency services or your fire department.

3. Immediately move outdoors or to an open door/window.

Warning: Carefully review your Carbon Monoxide Installation/User Guide to determine the necessary actions

required to ensure your safety and ensure that the equipment is operating correctly. Incorporate the steps outlined

in the guide into your evacuation plan.

- 13 -

Troubles

When a trouble condition is detected, the Trouble (

!

) or System indicator will turn on, and the keypad will

beep every 10 seconds. Press the (

!

) key to silence the beeps. Press (

!

) to view the trouble condition. The

Trouble (

!

) or System indicator will flash. The corresponding trouble will light up.

Troubles Comments Action

Service

Required (Press

for more

details)

Low Battery General System Supervision

Bell Circuit RF Jam Detected

General System Trouble Panel Low Battery

General System Tamper Panel AC Loss

Call for

service

AC Loss

If the building and/or neighborhood has lost electrical power, the system will

continue to operate on battery for several hours.

Call for

service

Phone Trouble The system has detected that the telephone line is disconnected.

Call for

service

Communication

Failure

The system attempted to communicate with the monitoring station, but failed.

This may be due to Telephone Line Fault.

Call for

service

Zone Fault

The system is experiencing difficulties with one or more sensors on the system.

Press to display the zone.

Call for

service

Zone Tamper

The system has detected a tamper condition with one or more sensors on the sys-

tem. Press to display the zone.

Call for

service

Wireless Low

Battery

The system has detected a low battery condition with one or more mod-

ules/sensors on the system. Press to display the zone, keypad, wireless key(s) and

RF Delinquency low battery conditions. Press again to see zone troubles.

Call for

service

Loss of Clock

If complete power was lost (AC and Battery), the time and date will need to be

reprogrammed.

Reprogram

Time &

Date

Limit Exceeded

[01] Interactive zone: The number of zones configured in the panel is not sup-

ported by ADC firmware (e.g.:>220)

[02] Interactive partition: The number of partitions configured is not supported

by ADC firmware (e.g.:>8)

Alarm Memory

When an alarm occurs, the Alarm indicator flashes.

To view which sensor(s) generated the alarm, press Alarms.

The sensor number where the alarm occurred will be displayed (e.g., zone 3). Use the [<][>] scroll keys to view the

sensors in alarm memory. Press Back or Home to exit. To clear the memory, arm and disarm the system. If an alarm

sounded while armed, the keypad will automatically go to alarm memory when you disarm the system. In this

instance, you should approach with caution, as the intruder may still be within the building/premises.

- 14 -

Troubles

Figure 5- Alarms in Memory

Sensor Reset

Certain sensors, after having detected an alarm condition, require a reset to exit the alarm condition (e.g., glass

break sensors, smoke detectors, etc.). Ask your alarm company if this function is required on your system.

To reset the detectors, press the Reset (Command Output 2 if the installer did not program a label) button on the

Outputs screen. If a sensor fails to reset, it may still be detecting an alarm condition. If the sensor reset is suc-

cessful, the alarm is canceled. If unsuccessful, the alarm will reactivate or continue.

Outputs

Your installer may have programmed these keys to perform various functions (reset smoke detector after an alarm,

open your garage door, etc.) To activate these functions, press Output and then press the appropriate option. For

additional information, refer to the section: Sensor reset.

Figure 6- Outputs

- 15 -

Additional Functions

Photos

You can create a slideshow of photos to View on the keypad. Photos are added using an SD card (32x24x2.1 mm.

Not supplied).

The photos must be .jpg format and can be up to 1280 x 720 in size. For best results, use 800 x 480 resolution.

Use photo editing software to adjust the size of your photos.

To start the slideshow, set the screen saver to photo mode. The slideshow plays automatically until the timeout is

reached or the screen is touched again.

To add photos:

1. Press Options, User Functions, Keypad Config, Picture Frame, Select Photos. Thumbnail images of the photos

on your SD card are displayed.

2. Touch an image to add it to the slideshow. Touch it a second time to remove it.

Use the Transition Time slider to program the amount of time each photo is on screen, from 5 seconds to 1

minute.

Use the Photo Frame Timeout slider to control how long your slideshow plays for, from 1 minute to 2 hours.

Select Never to keep the slideshow running until the screen is touched.

Note: Maximum of 255 photos are supported.

Quick Exit

If the system is armed and you need to exit, use the quick exit function to avoid disarming and rearming the sys-

tem. To activate this function, tap the Quick Exit icon. You have 2 minutes to leave the premises through your

exit door. When the door is closed again the remaining exit time is canceled.

Time & Date Programming

Tap on Options. Select User Functions [Master Code] and then select Time & Date. Tap on the section you would

like to change and use the up/down arrows to change time/date. Once done, press Save.

Keypad Mode

This option allows the HS2TCHPRO/HS2TCHPROBLK Touchscreen to function as a traditional DSC keypad.

Door Chime (Chime enable/disable)

The keypad indicates the current state of the door chime function (Enabled or Disabled). To choose the opposite

function, tap the 'Chime' icon. Three beeps indicate that the chime is ON (Enabled). One long beep indicates that

chime is OFF (Disabled).

Note: The door chime feature should be used in Disarmed mode only.

Zone Bypass

This screen allows you to view the status of the zones on the system.

- 16 -

Options Menu

Figure 7- Zone Closed

Zone Status Indicators

Ready Zone is closed

Open The zone is open and needs to be closed

Bypassed Zones

Use the zone bypass feature when a zone is open but the system needs to be armed. Bypassed zones will not cause

an alarm when opened. Bypassing zones reduces the level of security. If you are bypassing a zone because it is not

functioning, call a service technician immediately so that the problem can be resolved and your system returned to

proper working order.

Ensure that no zones are unintentionally bypassed when arming your system. Zone bypassing can only be per-

formed while the system is disarmed. Bypassed zones are automatically canceled each time the system is disarmed

and must be bypassed again, if required, before the next arming.

Note: 24-hour zones can only be unbypassed manually.

Note: For security reasons, your installer has programmed the system to prevent certain zones from being

bypassed. (e.g., smoke detectors).

Bypassing Zones with a HS2TCHPRO/HS2TCHPROBLK

When in the Zone Status page, scroll up/down through the desired zones, and tap on the bypass icon to bypass

the zone. To unbypass a zone, tap the unbypass icon.

Note: For UL listed installations, zones can only be bypassed manually.

Options Menu

Access the following functions by pressing Options on the right side of the home page. See the online

HS2TCHPRO/HS2TCHPROBLK User Manual for more information.

l Access Codes

l Installer Menu

l User Functions

l Chime Enabled/Disabled

l Partition Status

l Keypad Mode

- 17 -

Options Menu

Figure 8- Options

Access Codes

When Access Codes is selected from the Options menu, the keypad prompts for a Master Code. When a valid

Master Code is entered, a numeric keypad is displayed with arrows to scroll through the list of users. Press the

Select button to enter the user options.

Set Access Code: adds/edits the 4-digit or 6-digit code

Set Partitions: assigns the user to partitions

User Options: enables/disables different options for the user

Delete User: deletes the user from the system

The access codes have programmable attributes which allow zone bypassing, or one-time use activation.

Master Code (Access Code 01): The master code, if programmed, can only be changed by the installer.

Supervisor Codes: These codes can be used to program additional codes which have equal or lesser attributes.

Once programmed, the supervisor codes receive the master code’s attributes. These attributes are changeable. Any

user code can be made a supervisor code by enabling User Code Attribute 1 (see the following for details).

Duress Codes: Duress codes are standard user codes that transmit the Duress Reporting Code when entered to

perform any function on the system. Any user code can be made a duress code by enabling User Code Attribute 2

(see the following for details).

Note: Duress codes are not valid when entering User Programming, Master Functions or Installer’s sections.

Note: Access codes cannot be programmed as a duplicate or as a “Code +/- 1”.

Assign Proximity Tags

Depending on how your keypad is programmed, proximity tags can be used to either arm/disarm the system or to

perform a programmed function (e.g. unlock a cabinet or storeroom door). Present the tag to the tag reader.

1. Press [*][5]Master/Supervisor Code].

2. Enter a 4-digit or 6-digit user code.

3. Press 2.

4. Pass the enrolled tag near the tag reader.

Delete Proximity Tags

To delete a proximity tag:

1. Select Options, Access Codes [enter Master code].

2. Select a user to delete.

- 18 -

Options Menu

3. Select Prox Tag Prog then delete.

User Code Attributes

1. The default attributes of a new code will be the attributes of the code used to enter User Programming

whether it is a new code or an existing code being programmed.

2. System Master Code 01 has partition access for all partitions, as well as attributes 3-4 ON by default.

Note: These attributes are not changeable.

Inherent Attributes (all codes except installer and maintenance)

Arm/Disarm: Any access code with partition access enabled will be valid for arming and disarming that par-

tition.

Command Outputs ([*][7][1], [*][7][2], [*][7][3], and [*][7][4]): If these outputs require access code

entry, any Access Code with partition access will be valid for performing the command output functions on that

partition.

Programmable Attributes

1. Supervisor Code 5. For Future Use

2. Duress Code 6. For Future Use

3. Zone Bypassing Enabled 7. Bell Squawk upon Arming/Disarming

4. Remote Access 8. One Time Use Code

Bell Squawk Attribute

This attribute is used to determine whether an access code should generate an arming/disarming Bell Squawk upon

entry of the code for Away arming. The wireless keys with access codes associated with them may generate Arm-

ing/Disarming Bell squawks. If desired, this option may be used with codes that are manually entered. Please con-

tact your installer to have this programmed.

Note: The Master Code cannot use the Bell Squawk attribute, but is required to enable it for other codes.

Note: This feature cannot prevent the Arming/Disarming squawks from being generated if an access code assigned

to a wireless key is manually entered at a keypad.

Note: This feature is used to annunciate fire trouble signals and also trouble conditions for medical applications.

Partition Assignment

1. This section is used to assign users to available partitions. To assign partitions:

2. Select Options > Access Codes.

3. Enter the master code.

4. Select a user.

5. Select Partition Attributes.

6. Select the partition(s) to assign to the user.

Notes on Access Codes and Programming

l The master code’s attributes cannot be changed.

l When a new code is programmed in User Programming it will be checked against all other codes in the

system. If a duplicate code is found, an error tone is given and the code is returned to what it was before

it was changed. This applies to both 4 and 6-digit codes.

Erasing an Access Code

To erase a code, select the code and choose Delete User. The system will delete the code immediately and the user

will be returned to select another code.

Installer Menu

These functions are for the installer’s use only.

- 19 -

Options Menu

User Functions

First disarm the system then enter Options, User Functions, then Master Code. This command is used to gain

access to the following list of master functions of the system:

Time and Date

Enter desired time and date.

Auto-Arm Time

The system can be programmed to arm at a programmed time each day, per partition. Upon entry of this section,

enter the desired Auto-Arm time for each day of the week.

At the selected Auto-Arm time, the keypad buzzers will sound for a programmed amount of time (programmable

by the installer only) to warn that an auto-arm is in progress. The bell can also be programmed to squawk once

every 10 seconds during this warning period. When the warning period is complete, the system will arm with no

exit delay and in Away mode.

Auto-Arming can be canceled or postponed by entering a valid access code only during the programmed warning

period. Auto-Arming will be attempted at the same time the next day. When the Auto-Arming process is canceled

or postponed, the Auto-arm Cancelation Reporting Code will be transmitted (if programmed).

If arming is inhibited by one of the following, the Auto-Arm Cancelation transmission will be communicated:

l AC / DC Inhibit Arm

l Latching System Tampers

l Zone Expander Supervisory Fault

Note: For UL/ULC listed installations, the auto-arm feature shall be canceled when there are zones in an off-nor-

mal condition.

Enable DLS/Allow System Service

If enabled, the installer will be able to access Installer Programming via remote (DLS). The DLS window will

remain open for 6 hrs, during which time the installer will be able to enter DLS an unlimited number of times.

After the 6-hr window has expired, Installer’s Programming will be unavailable again until the window is re-

opened.

Event Buffer

l Displays the date, time and the full description of the event

l The Log is organized from the most recent event (Top) to past events (Down)

l The Left arrow scrolls forward in time

l The Right arrow scrolls back in time

l The Back returns you to the Home screen

l This screen will time out to the Home screen after 30 seconds of inactivity

System Test

The system’s bell output, keypad lights and communicator are tested. This test will also measure the panel’s

standby battery.

Important:

l To ensure that your system continues to function as intended, you must test your system weekly.

l For UL HOME HEALTH CARE listed applications, the system shall also be tested weekly without AC

power. To remove AC from the control unit, remove the screw from the restraining tab of the plug in

adapter and remove the adapter from the AC outlet. After completing the test of the unit using only the

battery backup source, reconnect the plug in adapter and attach the screw through the restraining tab, so

that the adapter is securely attached to the outlet.

l Should your system fail to function properly, contact your installation company immediately.

- 20 -

La page charge ...

Tyco Tyco HC2TCHPRO Manuel utilisateur

Ce manuel convient également à

Tyco Tyco HC2TCHPRO Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents